TY - THES A1 - Jelken, Joachim T1 - Surface relief and bulk birefringence gratings in photo-sensitive polymer films T1 - Realzeit Observierung der Entstehung von Volumen- und Oberflächengittern in photosensitiven Polymerfilmen mittels der Rasterkraftmikroskopie und Messung der Beugungseffizienz BT - in-situ probing and manipulation in real time N2 - This thesis is focused on a better understanding of the formation mechanism of bulk birefringence gratings (BBG) and a surface relief gratings (SRG) in photo-sensitive polymer films. A new set-up is developed enabling the in situ investigation how the polymer film is being structured during irradiation with modulated light. The new aspect of the equipment is that it combines several techniques such as a diffraction efficiency (DE) set-up, an atomic force microscope (AFM) and an optical set-up for controlled illumination of the sample. This enables the simultaneous acquiring and differentiation of both gratings (BBG and SRG), while changing the irradiation conditions in desired way. The dissertation is based on five publications. The first publication (I) is focused on the description of the set-up and interpretation of the measured data. A fine structure within the 1st-order diffraction spot is observed, which is a result of the inhomogeneity of the inscribed gratings. In the second publication (II) the interplay of BBG and SRG in the DE is discussed. It has been found, that, dependent on the polarization of a weak probe beam, the diffraction components of the SRG and BBG either interfere constructively or destructively in the DE, altering the appearance of the intensity distribution within the diffracted spot. The third (III) and fourth (IV) publications describe the light-induced reconfiguration of surface structures. Special attention is payed to conditions influencing the erasure of topography and bulk gratings. This can be achieved via thermal treatment or illumination of the polymer film. Using the translation of the interference pattern (IP) in a controlled way, the optical erase speed is significantly increased. Additionally, a dynamic reconfigurable surface is generated, which could move surface attached objects by the continuous translation of the interference pattern during irradiation of the polymer films. The fifth publication (V) deals with the understanding of polymer deformation under irradiation with SP-IP, which is the only IP generating a half-period topography grating (compared to the period of the IP) on the photo-sensitive polymer film. This mechanism is used, e.g. to generate a SRG below the diffraction limit of light. It also represents an easy way of changing the period of the surface grating just by a small change in polarization angle of the interfering beams without adjusting the optical pass of the two beams. Additionally, complex surface gratings formed in mixed polarization- and intensity interference patterns are shown. I J. Jelken, C. Henkel and S. Santer, Applied Physics B, 125 (2019), 218 II J. Jelken, C. Henkel and S. Santer, Appl. Phys. Lett., 116 (2020), 051601 III J. Jelken and S. Santer, RSC Advances, 9 (2019), 20295 IV J. Jelken, M. Brinkjans, C. Henkel and S. Santer, SPIE Proceedings, 11367 (2020), 1136710 V J. Jelken, C. Henkel and S. Santer, Formation of Half-Period Surface Relief Gratings in Azobenzene Containing Polymer Films (submitted to Applied Physics B) N2 - In dieser kumulativen Dissertation, basierend auf fünf Publikationen, geht es darum ein Verständnis über die grundlegenden Mechanismen zu entwickeln, welche hinter der Entstehung von Oberflächen- und Volumengittern in amorphen photo-sensitiven Polymerfilmen stehen. Hierzu wurde ein neuer Versuchsaufbau entwickelt, welcher in situ (d.h. während der Belichtung mit einem Interferenzgitter) Messungen der zeitlichen Entwicklung (Entstehung oder Löschung) von Volumen- als auch Oberflächengittern unabhängig voneinander ermöglicht. Dies stellt einen erheblichen Vorteil gegenüber dem gängigen Verfahren der Beugungseffizienzmessung dar, weil dort die Anteile der beiden Gitter durch aufwendige mathematische Behandlung voneinander getrennt werden müssen. Hierzu wurde ein Rasterkraftmikroskop (AFM, atomic force microscope) in einen optischen Aufbau zur Erzeugung eines Interferenzgitters, welches zur Belichtung des Polymerfilms benutzt wird, integriert. Zusätzlich wurde außerdem die Beugung eines Sondenstrahls an den entstehenden Gittern detektiert. Die erste Publikation (I) beschäftigt sich mit der grundsätzlichen Interpretation der mit diesem neuen Messaufbau erzielten Ergebnisse. Es wurde eine Feinstruktur in dem räumlichen Profil der ersten Beugungsordnung gemessen, deren Ursprung aus der Inhomogenität der erzeugten Gitter herrührt. In der zweiten Publikation (II) wird die Kopplung von Oberflächen- und Volumengitter in der aufgezeichneten Beugungseffizienz untersucht. Es wird gezeigt, dass, abhängig von der Polarisation des Sondierungsstrahls, diese Kopplung sowohl konstruktiv als auch destruktiv sein kann, was auch die in der ersten Publikation beschriebene Feinstruktur beeinflusst. Die dritte (III) und vierte (IV) Publikation beschäftigen sich mit dem dynamischen Umbau von Oberflächenstrukturen. Hierzu muss das erzeugte Oberflächengitter möglichst schnell wieder gelöscht werden können. Dies kann sowohl thermisch, als auch optisch erfolgen. Durch eine definierte Translation des Interferenzgitters konnte hier die optische Löschgeschwindigkeit signifikant gesteigert werden. Zum anderen wird auch die Möglichkeit des Transports oberflächenadsorbierter Objekte durch die Erzeugung einer dynamisch modulierten Oberfläche (mittels einer kontinuierlichen Translation des Interferenz- und dadurch des Oberflächengitters) aufgezeigt. Die Hypothese des Massentransports wird hierbei kritisch untersucht. Die fünften Publikation (V) widmet sich dem SP-Interferenzgitter, welches als einziges Gitter eine Periode der Oberflächenstruktur ausbildet, die der Hälfte der Periode des optischen Interferenzgitters entspricht. Diese Eigenschaft kann zum einen für die Erzeugung von Oberflächengittern unterhalb der optischen Auflösungsgrenze benutzt werden, zum anderen erlaubt sie die Periode der Oberflächenstruktur einfach zu ändern, indem die Beleuchtung zu einem anderen Interferenzgitter geschaltet wird. Zusätzlich wird auch die Erzeugung von komplexen Oberflächengittern durch Misch-Interferenzgitter (Mischung aus Polarisations- und Intensitäts-Interferenzgitter) diskutiert. I J. Jelken, C. Henkel and S. Santer, Applied Physics B, 125 (2019), 218 II J. Jelken, C. Henkel and S. Santer, Appl. Phys. Lett., 116 (2020), 051601 III J. Jelken and S. Santer, RSC Advances, 9 (2019), 20295 IV J. Jelken, M. Brinkjans, C. Henkel and S. Santer, SPIE Proceedings, 11367 (2020), 1136710 V J. Jelken, C. Henkel and S. Santer, Formation of Half-Period Surface Relief Gratings in Azobenzene Containing Polymer Films (eingereicht bei Applied Physics B) KW - photosensitive Polymer KW - Surface Relief Grating (SRG) KW - sub-diffraction gratings KW - azobenzene containing molecules KW - Atomic Force Microscope KW - diffraction efficiency KW - photo-structuring of polymer films KW - Rasterkraftmikroskopie KW - Beugungseffizienz KW - Oberflächengitter KW - Azobenzol enthaltende Moleküle KW - Photostrukturierung von Polymerfilmen KW - Photopolymer Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-483988 ER - TY - THES A1 - Yadavalli, Nataraja Sekhar T1 - Advances in experimental methods to probe surface relief grating formation mechanism in photosensitive materials T1 - Entstehung von Oberflächengittern in lichtempfindlichen Materialien N2 - When azobenzene-modified photosensitive polymer films are irradiated with light interference patterns, topographic variations in the film develop that follow the electric field vector distribution resulting in the formation of surface relief grating (SRG). The exact correspondence of the electric field vector orientation in interference pattern in relation to the presence of local topographic minima or maxima of SRG is in general difficult to determine. In my thesis, we have established a systematic procedure to accomplish the correlation between different interference patterns and the topography of SRG. For this, we devise a new setup combining an atomic force microscope and a two-beam interferometer (IIAFM). With this set-up, it is possible to track the topography change in-situ, while at the same time changing polarization and phase of the impinging interference pattern. To validate our results, we have compared two photosensitive materials named in short as PAZO and trimer. This is the first time that an absolute correspondence between the local distribution of electric field vectors of interference pattern and the local topography of the relief grating could be established exhaustively. In addition, using our IIAFM we found that for a certain polarization combination of two orthogonally polarized interfering beams namely SP (↕, ↔) interference pattern, the topography forms SRG with only half the period of the interference patterns. Exploiting this phenomenon we are able to fabricate surface relief structures below diffraction limit with characteristic features measuring only 140 nm, by using far field optics with a wavelength of 491 nm. We have also probed for the stresses induced during the polymer mass transport by placing an ultra-thin gold film on top (5–30 nm). During irradiation, the metal film not only deforms along with the SRG formation, but ruptures in regular and complex manner. The morphology of the cracks differs strongly depending on the electric field distribution in the interference pattern even when the magnitude and the kinetic of the strain are kept constant. This implies a complex local distribution of the opto-mechanical stress along the topography grating. The neutron reflectivity measurements of the metal/polymer interface indicate the penetration of metal layer within the polymer resulting in the formation of bonding layer that confirms the transduction of light induced stresses in the polymer layer to a metal film. N2 - Azobenzolhaltige Polymere gehören zu einer Klasse funktionaler Materialien, bei denen durch ein äußeres Strahlungsfeld eine starke mechanische Reaktion ausgelöst werden kann. Durch die Bindung an das Polymerrückgrat können die Azobenzole, die unter UV-Belichtung eine Photoisomerisierung ausführen, was zum Teil drastische Effekte zur Folge hat. Unter Belichtung mit Intensitätsmustern, d.h. mit räumlich variierender Verteilung der Polarisation oder der Intensität des einfallenden Lichts verändert sich die Topographie der azobenzolhaltigen Filme, was zur Bildung von Oberflächengittern (engl. Surface Relief Gratings, SRG) führt. In dieser Arbeit wurde eine neue Methode vorgeschlagen, bei der das Verhalten elastischer/morphologischer Eigenschaften unter verschiedenen Belichtungsbedingungen, d.h. mit unterschiedlicher Verteilung der Polarisation und der Intensität in situ lokal als Funktion der Position entlang der SRG aufgenommen werden kann. Außerdem wurde hier vorgeschlagen, opto-mechanische Spannungen, die innerhalb der photosensitiven Polymerfilme während der Belichtung entstehen, mit Hilfe dünner aufgebrachter metallischen Schichten abzubilden und zu analysieren. KW - Azobenzolhaltige Polymerfilme KW - Oberflächengitter KW - In-situ Rasterkraftmikroskopie KW - Opto-mechanische Spannungen KW - Metall/Graphen/Polymer Grenzfläch KW - azobenzene polymer films KW - surface relief grating KW - in-situ atomic force microscopy KW - opto-mechanical stresses KW - metal/polymer interfaces Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-71213 ER -