TY - THES A1 - Abouserie, Ahed T1 - Ionic liquid precursors for multicomponent inorganic nanomaterials T1 - Ionische Flüssigkeiten als Vorstufe für anorganische Mehrkomponenten-Nanomaterialien N2 - Health effects, attributed to the environmental pollution resulted from using solvents such as benzene, are relatively unexplored among petroleum workers, personal use, and laboratory researchers. Solvents can cause various health problems, such as neurotoxicity, immunotoxicity, and carcinogenicity. As such it can be absorbed via epidermal or respiratory into the human body resulting in interacting with molecules that are responsible for biochemical and physiological processes of the brain. Owing to the ever-growing demand for finding a solution, an Ionic liquid can use as an alternative solvent. Ionic liquids are salts in a liquid state at low temperature (below 100 C), or even at room temperature. Ionic liquids impart a unique architectural platform, which has been interesting because of their unusual properties that can be tuned by simple ways such as mixing two ionic liquids. Ionic liquids not only used as reaction solvents but they became a key developing for novel applications based on their thermal stability, electric conductivity with very low vapor pressure in contrast to the conventional solvents. In this study, ionic liquids were used as a solvent and reactant at the same time for the novel nanomaterials synthesis for different applications including solar cells, gas sensors, and water splitting. The field of ionic liquids continues to grow, and become one of the most important branches of science. It appears to be at a point where research and industry can work together in a new way of thinking for green chemistry and sustainable production. N2 - Der Einfluss von kommerziellen organischen Lösungsmitteln auf den menschlichen Körper ist bekannt, jedoch nicht ausreichend untersucht worden. Spezielle Lösungsmittel wie Benzol, welche auch vermehrt in der Petrolchemie genutzt werden, zeigen akute Toxizität auf den biologischen Organismus. Daher ist der Bedarf der Verwendung eines alternativen Lösungsmittel groß. Ionische Flüssigkeiten können hier potentiell eine Alternative sein. Als Ionische Flüssigkeiten (ILs) werden Salze in flüssigem Zustand bei niedriger Temperatur (unter 100 °C) oder sogar bei Raumtemperatur definiert. Aufgrund ihrer Variabilität in der Zusammensetzung der strukturellen ionischen Moleküle ergeben sich ungewöhnliche Eigenschaften, welche auf einfachste Weise durch Mischen zweier ionischer Flüssigkeiten beliebig angepasst werden können. ILs werden sowohl als gewöhnliche Lösungsmittel verwendet, jedoch entwickelten sie sich aufgrund ihrer besonderen Eigenschaften vermehrt zu Reaktionsagenzien. Dies ist zurückzuführen auf ihre gute thermische Stabilität, elektrische Leitfähigkeit und ihrem geringen Dampfdruck. In dieser Arbeit wurden nun spezielle Ionische Flüssigkeiten speziell auf ihr Verhalten in chemischen Reaktionen als Reagenz untersucht. Als Ausgangsreaktion diente hierbei eine neuartige Synthese von Nanomaterialen, welche speziell in Solarzellen, Gassensoren und auch in der katalytischen Wasserspaltung genutzt werden. Das Anwendungspotenzial der ILs gewinnt immer mehr an Bedeutung und führt in der Forschung sowie auch in der Industrie zu neuen Denkweisen für nachhaltige Produktionen und auch Entwicklungen. KW - ionic liquids KW - Alkylpyridinium salts KW - Structure elucidation KW - Phase transitions KW - Nanoparticles KW - Metal Chalcogenides KW - Organic photovoltaic Cell KW - Ionische Flüssigkeiten KW - Alkylpyridinium-Salze KW - Strukturaufklärung KW - Phasenübergänge KW - Nanopartikel KW - Metallchalkogenide KW - Organische Photovoltaikzelle Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-418950 ER - TY - THES A1 - Adelhelm, Philipp T1 - Novel carbon materials with hierarchical porosity : templating strategies and advanced characterization T1 - Neue Kohlenstoffmaterialien mit hierarchischer Porosität : Strategien der Templatierung und erweiterte Charakterisierung N2 - The aim of this work was the generation of carbon materials with high surface area, exhibiting a hierarchical pore system in the macro- and mesorange. Such a pore system facilitates the transport through the material and enhances the interaction with the carbon matrix (macropores are pores with diameters > 50 nm, mesopores between 2 – 50 nm). Thereto, new strategies for the synthesis of novel carbon materials with designed porosity were developed that are in particular useful for the storage of energy. Besides the porosity, it is the graphene structure itself that determines the properties of a carbon material. Non-graphitic carbon materials usually exhibit a quite large degree of disorder with many defects in the graphene structure, and thus exhibit inherent microporosity (d < 2nm). These pores are traps and oppose reversible interaction with the carbon matrix. Furthermore they reduce the stability and conductivity of the carbon material, which was undesired for the proposed applications. As one part of this work, the graphene structures of different non-graphitic carbon materials were studied in detail using a novel wide-angle x-ray scattering model that allowed precise information about the nature of the carbon building units (graphene stacks). Different carbon precursors were evaluated regarding their potential use for the synthesis shown in this work, whereas mesophase pitch proved to be advantageous when a less disordered carbon microstructure is desired. By using mesophase pitch as carbon precursor, two templating strategies were developed using the nanocasting approach. The synthesized (monolithic) materials combined for the first time the advantages of a hierarchical interconnected pore system in the macro- and mesorange with the advantages of mesophase pitch as carbon precursor. In the first case, hierarchical macro- / mesoporous carbon monoliths were synthesized by replication of hard (silica) templates. Thus, a suitable synthesis procedure was developed that allowed the infiltration of the template with the hardly soluble carbon precursor. In the second case, hierarchical macro- / mesoporous carbon materials were synthesized by a novel soft-templating technique, taking advantage of the phase separation (spinodal decomposition) between mesophase pitch and polystyrene. The synthesis also allowed the generation of monolithic samples and incorporation of functional nanoparticles into the material. The synthesized materials showed excellent properties as an anode material in lithium batteries and support material for supercapacitors. N2 - Kohlenstoffmaterialien finden aufgrund ihrer Vielseitigkeit heute in den unterschiedlichsten Bereichen des täglichen Lebens ihren Einsatz. Bekannte Beispiele sind Kohlenstofffasern in Verbundwerkstoffen, Graphit als trockenes Schmiermittel, oder Aktivkohlen in Filtersystemen. Ferner wird Graphit als Elektrodenmaterial auch in Lithium-Ionen-Batterien verwendet. Wegen knapper werdender Ressourcen von Öl und Gas wurde in den letzten Jahren verstärkt an der Entwicklung neuer Materialien für die Speicherung von Wasserstoff und elektrischer Energie gearbeitet. Die Nanotechnologie ist dabei auch für neue Kohlenstoffmaterialien zukunftsweisend, denn sie stellt weitere Anwendungsmöglichkeiten in Aussicht. In dieser Arbeit wurden hierzu mittels des sogenannten Nanocastings neue Kohlenstoffmaterialien für Energieanwendungen, insbesondere zur Speicherung von elektrischer Energie entwickelt. Die Eigenschaften eines Kohlenstoffmaterials beruhen im Wesentlichen auf der Struktur des Kohlenstoffs im molekularen Bereich. Die in dieser Arbeit hergestellten Materialen bestehen aus nichtgraphitischem Kohlenstoff und wurden im ersten Teil der Arbeit mit den Methoden der Röntgenstreuung genau untersucht. Eine speziell für diese Art von Kohlenstoffen kürzlich entwickelte Modellfunktion wurde dazu an die experimentellen Streubilder angepasst. Das verwendete Modell basiert dabei auf den wesentlichen Strukturmerkmalen von nichtgraphitischem Kohlenstoff und ermöglichte von daher eine detaillierte Beschreibung der Materialien. Im Gegensatz zu den meisten nichtgraphitischen Kohlenstoffen konnte gezeigt werden, dass die Verwendung von Mesophasen-Pech als Vorläufersubstanz (Precursor) ein Material mit vergleichsweise geringem Grad an Unordnung ermöglicht. Solch ein Material erlaubt eine ähnlich reversible Einlagerung von Lithium-Ionen wie Graphit, weist aber gleichzeitig wegen des nichtgraphitischen Charakters eine deutlich höhere Speicherfähigkeit auf. Zur Beschreibung der Porosität eines Materials verwendet man die Begriffe der Makro-, Meso-, und Mikroporen. Die Aktivität eines Materials kann durch die Erhöhung der Oberfläche noch erheblich gesteigert werden. Hohe Oberflächen können insbesondere durch die Schaffung von Poren im Nanometerbereich erzielt werden. Um die Zugänglichkeit zu diesen Poren zu steigern, weist ein Material idealerweise zusätzlich ein kontinuierliches makroporöses Transportsystem (Porendurchmesser d > 50 nm) auf. Solch eine Art von Porosität über mehrere Größenordnungen wird allgemein als „hierarchische Porosität“ bezeichnet. Für elektrochemische Anwendungen sind sogenannte Mesoporen (d = 2 – 50 nm) relevant, da noch kleinere Poren (Mikroporen, d < 2 nm) z.B. zu einer irreversiblen Bindung von Lithium- Ionen führen können. Wird Mesophasen-Pech als Kohlenstoffprekursor verwendet, kann die Entstehung dieser Mikroporen verhindert werden. Im zweiten und dritten Teil der Arbeit konnte mit den Methoden des „Nanocastings“ zum ersten Mal die spezielle Struktur des Mesophasen-Pech basierenden Kohlenstoffmaterials mit den Vorteilen einer hierarchischen (makro- / meso-) Porosität kombiniert werden. Im ersten Syntheseverfahren wurde dazu ein sogenanntes „hartes Templat“ mit entsprechender Porosität aus Siliziumdioxid repliziert. Aufgrund der hohen Viskosität des Pechs und der geringen Löslichkeit wurde dazu ein Verfahren entwickelt, das die Infiltration des Templates auch auf der Nanometerebene ermöglicht. Das Material konnte in Form größerer Körper (Monolithen) hergestellt werden, die im Vergleich zu Pulvern eine bessere technische Verwendung ermöglichen. Im zweiten Syntheseverfahren konnte die Herstellung eines hierarchisch makro- / mesoporösen Kohlenstoffmaterials erstmals mittels eines weichen Templates (organisches Polymer) erreicht werden. Die einfache Entfernung von weichen Templaten durch eine geeignete Temperaturbehandlung, macht dieses Verfahren im Vergleich zu hart templatierten Materialien kostengünstiger und stellt eine technische Umsetzung in Aussicht. Desweiteren erlaubt das Syntheseverfahren die Herstellung von monolithischen Körpern und die Einbindung funktionaler Nanopartikel. Die hergestellten Materialien zeigen exzellente Eigenschaften als Elektrodenmaterial in Lithium-Ionen-Batterien und als Trägermaterial für Superkondensatoren. KW - Mesoporosität KW - hierarchische Porosität KW - weiche und harte Templatierung KW - Kohlenstoffmaterialien KW - Weitwinkelröntgenstreuung KW - Mesoporosity KW - hierarchical porosity KW - soft and hard templating KW - carbon materials KW - wide-angle x-ray scattering Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-15053 ER - TY - THES A1 - Akdemir, Özgür T1 - Synthesis of novel non-viral gene carriers via atom transfer radical polymerization and click chemistry Y1 - 2009 CY - Potsdam ER - TY - THES A1 - Al Nakeeb, Noah T1 - Self-assembly and crosslinking approaches of double hydrophilic linear-brush block copolymers BT - a biocompatible platform for the next generation of nanoreactors Y1 - 2019 ER - TY - THES A1 - Alahverdjieva, Veneta T1 - Experimental study of mixed protein/surfactant systems at the aqueous solution/air interface Y1 - 2007 CY - Potsdam ER - TY - THES A1 - Ali, Abu Md. Imroz T1 - Morphology control in nanoscopic composite polymer particles Y1 - 2005 CY - Potsdam ER - TY - THES A1 - Altabal, Osamah T1 - Design and fabrication of geometry-assisted on-demand dosing systems N2 - The controlled dosage of substances from a device to its environment, such as a tissue or an organ in medical applications or a reactor, room, machinery or ecosystem in technical, should ideally match the requirements of the applications, e.g. in terms of the time point at which the cargo is released. On-demand dosage systems may enable such a desired release pattern, if the device contain suitable features that can translate external signals into a release function. This study is motivated by the opportunities arising from microsystems capable of an on-demand release and the contributions that geometrical design may have in realizing such features. The goals of this work included the design, fabrication, characterization and experimental proof-of-concept of geometry-assisted triggerable dosing effect (a) with a sequential dosing release and (b) in a self-sufficient dosage system. Structure-function relationships were addressed on the molecular, morphological and, with a particular attention, the device design level, which is on the micrometer scale. Models and/or computational tools were used to screen the parameter space and provide guidance for experiments. N2 - Die kontrollierte Freisetzung von Substanzen aus einem Device in seine Umgebung, wie ein Gewebe oder Organ in medizinischen Anwendungen oder ein Reaktor, ein Raum, ein Gerät oder ein Ökosystem in technischer Nutzung sollte idealerweise den Anforderungen des Einsatzzweckes entsprechen, beispielsweise hinsichtlich des Zeitpunktes an dem die Freisetzung erfolgt. On-demand Freisetzungssysteme könnten eine derartiges gewünschtes Verhalten zeigen, wenn das System die Befähigung besitzt, externe Signale in eine Freisetzungsfunktion zu überführen. Diese Arbeit greift die Möglichkeiten auf, die sich durch den Einsatz und ein gezieltes Design von mikrostrukturierten Systemen für die Realisierung einer on-demand Freisetzung ergeben könnten. Die Ziele der Arbeit umfassen die Konzeptionierung, Herstellung, Charakterisierung sowie den grundsätzlichen Nachweis durch Stimuli induzierten on-demand Freisetzungsfunktion einerseits in Form eines sequentiellen Freigabeverhaltens und anderseits in Form eines autarken (kontaktfrei ausgelösten) Dosiersystems. Struktur-Eigenschafts-Beziehungen wurden auf molekularer, morphologischer und - mit besonderen Augenmerk - auf der Ebene des Device-Designs untersucht. Modelle und/oder Computer-gestützte Verfahren wurden verwendet um geeignete Materialparameter zu identifizieren und einen Leitfaden für die Experimente bereitzustellen. KW - Stress concentration KW - Negative Poisson’s ratio KW - On-demand release KW - Spannungskonzentrationen KW - Negatives Poisson-Verhältnis KW - On-demand Freisetzung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-532441 ER - TY - THES A1 - Ambrogi, Martina T1 - Application of Poly(Ionic Liquid)s for the synthesis of functional carbons Y1 - 2015 ER - TY - THES A1 - Andersen, Audrée T1 - Surfactant dynamics at interfaces : a series of second harmonic generation experiments T1 - Surfactant Dynamik an Grenzflächen : eine Studie über SHG-Experimente N2 - Adsorption layers of soluble surfactants enable and govern a variety of phenomena in surface and colloidal sciences, such as foams. The ability of a surfactant solution to form wet foam lamellae is governed by the surface dilatational rheology. Only systems having a non-vanishing imaginary part in their surface dilatational modulus, E, are able to form wet foams. The aim of this thesis is to illuminate the dissipative processes that give rise to the imaginary part of the modulus. There are two controversial models discussed in the literature. The reorientation model assumes that the surfactants adsorb in two distinct states, differing in their orientation. This model is able to describe the frequency dependence of the modulus E. However, it assumes reorientation dynamics in the millisecond time regime. In order to assess this model, we designed a SHG pump-probe experiment that addresses the orientation dynamics. Results obtained reveal that the orientation dynamics occur in the picosecond time regime, being in strong contradiction with the two states model. The second model regards the interface as an interphase. The adsorption layer consists of a topmost monolayer and an adjacent sublayer. The dissipative process is due to the molecular exchange between both layers. The assessment of this model required the design of an experiment that discriminates between the surface compositional term and the sublayer contribution. Such an experiment has been successfully designed and results on elastic and viscoelastic surfactant provided evidence for the correctness of the model. Because of its inherent surface specificity, surface SHG is a powerful analytical tool that can be used to gain information on molecular dynamics and reorganization of soluble surfactants. They are central elements of both experiments. However, they impose several structural elements of the model system. During the course of this thesis, a proper model system has been identified and characterized. The combination of several linear and nonlinear optical techniques, allowed for a detailed picture of the interfacial architecture of these surfactants. N2 - Amphiphile vereinen zwei gegensätzliche Strukturelemente in einem Molekül, eine hydrophile Kopfgruppe und ein hydrophobe, meist aliphatische Kette. Aufgrund der molekularen Asymmetrie erfolgt eine spontane Adsorption an der Wasser-Luft Grenzfläche. Die Adsorptionsschicht verändert die makroskopischen Eigenschaften des Materials, z.B. die Grenzflächenspannung wird erniedrigt. Amphiphile sind zentrale Bauelemente der Kolloid- und Grenzflächenforschung, die Phänomene, wie Schäume ermöglichen. Eine Schaumlamelle besteht aus einem dünnen Wasserfilm, der durch zwei Adsorptionsschichten stabilisiert wird. Die Stabilität der Lamelle wird durch die Grenzflächenrheologie entscheidend geprägt. Die wesentliche makroskopische Größe in diesem Zusammenhang ist das so genannte Grenzflächendilatationsmodul E. Es beschreibt die Fähigkeit des Systems die Gleichgewichtsgrenzflächenspannung nach einer Expansion oder Dilatation der Adsorptionschicht wieder herzustellen. Das Modul E ist eine komplexe Größe, in dem der Imaginärteil direkt mit der Schaumstabilität korreliert. Diese Arbeit widmet sich der Grenzflächenrheologie. In der Literatur werden zwei kontroverse Modelle zur Interpretation dieser Größe diskutiert. Diese Modelle werden experimentell in dieser Arbeit überprüft. Dies erfordert die Entwicklung neuer experimenteller Aufbauten basierend auf nichtlinearen, optischen Techniken. Mit diesen Experimenten konnte eines der Modelle bestätigt werden. KW - Tensid KW - Grenzflächenchemie KW - Nichtlineare Spektroskopie KW - Oscillating Bubble KW - surfactants KW - nonlinear optics KW - surface rheology KW - air-water interface KW - oscillating bubble Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-6553 ER - TY - THES A1 - Antipov, Alexei T1 - Polyelectrolyte multilayer capsules as controlled permeability vehicles and catalyst carriers Y1 - 2003 ER - TY - THES A1 - Appajaiah, Anilkumar T1 - Climatic stability of polymer optical fibers (POF) N2 - Optische Polymerfasern stellen ein relativ neues Medium zur Hochgeschwindigkeitsdatenübertragung mittels moduliertem Licht dar. Sie gestatten die Verbreitung großer Datenmengen über Entfernungen bis zu ca. 100 m, ohne eine Beeinflussung durch externe elektromagnetischen Feldern. Jedoch reagieren die Fasern und somit auch ihre optischen Eigenschaften aufgrund des organischchemischen Faseraufbaus empfindlich auf das Klima ihrer Umgebung. Die Ursachen für die Abnahme der optischen Transmission aufgrund von klimatischen Einflüssen (Alterung, Degradation) werden mittels chemisch analytischer Verfahren wie Chemilumineszenz (CL) und Fourier Transform Infrarot (FTIR) Spektroskopie untersucht. Dabei kommen fünf, von verschiedenen Herstellern bezogene, Multimode- POFs aus PMMA in sieben verschiedenen Klimaten zum Einsatz. Drei dieser fünf POFs werden genauer untersucht, um den Einfluss einzelner Parameter festzustellen und optische Langzeitstabilität aufgrund von Kurzzeittests vorherzusagen. Als erstes erfolgt eine Kennzeichnung unbeanspruchter POF Komponenten (Kern, Mantel und nackte POF als Kombination von Kern und Mantel) über ihre physikalischen und chemischen Eigenschaften. Die Glas- und die Schmelztemperaturen liegen im Bereich von 120 °C bis 140 °C, das Molekulargewicht des Kerns bei größenordnungsmäßig 105 g mol-1 ;. FTIR-Messungen zeigen zwar Unterschiede in der chemischen Zusammensetzung der Mäntel aber keine Unterschiede bei den Kernen. Bei zwei der POF Proben , die als Kabel (Kern, Mantel und Schutzhülle) für 3300 Stunden einem Klima aus 92 °C und 95 % relativer Feuchte (r.F.) ausgesetzt waren, verringern sich daraufhin die optische Transmissionen in unterschiedlicher Weise. Die Untersuchung der zugehörigen nackten POFs mittels CL, FTIR, Thermogravimetrie (TG), UV/VIS und Gel Permeation Chromatographie (GPC) lässt eine stärkere Schädigung der Mäntel als der Kerne vermuten. Wahrscheinlich führt eine starke Manteldegradation zu einer erhöhten Absorption und Fehlstellen im Mantel und damit zu einer Transmissionsabnahme. Daher scheint die optische Stabilität der POF stärker durch die thermo-oxidative Stabilität des Mantels bestimmt zu sein als durch die des Kernes. Drei nackte POFs (Kern und Mantel) sind unterschiedlich lang (30 Stunden bis 3000 Stunden) folgenden Klimaten ausgesetzt: 92 °C / 95 % r.F., 92 °C / 50 % r.F., 50 °C / 95 % r.F., 90 °C / geringe Feuchte, 100 °C / geringe Feuchte, 110 °C / geringe Feuchte and 120 °C / geringe Feuchte. Auch in diesen Klimaten ergaben sich probenbedingte unterschiedliche Transmissionsänderungen. Die Ergebnisse deuten stark darauf hin, dass bei gleichzeitig hoher Temperatur und hoher Feuchte physikalische Änderungen wie die Volumenausdehnung die Hauptursachen für die Abnahme der optischen Transmission bilden. Ein weiterer Einflussfaktor ist die chemische Zusammensetzung der Mäntel. Bei Kombination von hoher Temperatur und geringer Feuchte erzeugen in den Anfangsstadien der Alterung physikalische Änderungen Transmissionsabnahmen, vermutlich entstehen Fehlstellen in der Kern-Mantel-Grenzschicht. Hinzukommen in den späteren Stadien wahrscheinlich zunehmende Lichtabsorption in Kern und Mantel. L. Jankowski (Doktorand in der BAM) bestätigt diese Annahme durch parallel ausgeführte optische Simulationsrechnungen. Auch für nackte POFs scheint also die thermo-oxidative Stabilität die optische Stabilität zu bestimmen. Kurzzeitalterungstests sollen Aufschluss über den Einfluss individueller Klimaparameter auf die POF Eigenschaften geben. Es zeigt sich bei dauerhaft hoher Temperatur und variabler Feuchte aufgrund des physikalisch absorbierten Wassers bis zu einem gewissen Grad ein reversibles Verhalten des Transmissionsverlustes. Dieses Verhalten tritt aber nur kaum merkbar auf, wenn bei konstanter hoher Feuchte die Temperatur variiert wird. Bei Raumtemperatur und variabler Feuchte stellt sich jedoch ein voll reversibles Verhalten des Transmissionsverlustes ein. Die hier beschriebenen Untersuchungen sind als Ausgangspunkt für weitergehende Forschungen zu verstehen. Die begrenzte Zurverfügungstellung von POF Basisdaten durch die Hersteller und der zeitaufwendige klimabedingte Alterungsprozess beschränken die Ergebnisse mehr oder weniger auf die untersuchten Proben. Signifikante allgemeine Aussagen erfordern aber beispielsweise zusätzliche statistische Daten der Produktionsschwankungen von POF Eigenschaften. Dennoch besitzen die hier beschriebenen Tests das Potential für eine Annäherung an die optische Langzeitstabilität und deren Vorhersage. N2 - Polymer optical fibers (POFs) are a rather new tool for high-speed data transfer by modulated light. They allow the transport of high amounts of data over distances up to about 100 m without be influenced by external electromagnetic fields. Due to organic chemical nature of POFs, they are sensitive to the climate of their environment and therefore the optical fiber properties are as well. Hence, the optical stability is a key issue for long-term applications of POFs. The causes for a loss of optical transmission due to climatic exposures (aging/degradation) are researched by means of chemical analytical tools such as chemiluminescence (CL) and Fourier transform infrared (FTIR) spectroscopy for five different (with respect to manufacturers) step-index multimode PMMA based POFs and for seven different climatic conditions. Three of the five POF samples are studied more in detail to realize the effects of individual parameters and for forecasting longterm optical stability by short-term exposure tests. At first, the unexposed POF components (core, cladding, and bare POF as combination of core and cladding) are characterized with respect to important physical and chemical properties. The glass transition temperature Tg, and the melting temperature Tm are in the region of 120 °C to 140 °C, the molecular weight (Mw) of cores is in the order of 105 g mol-1. POFs are found to have different chemical compositions of their claddings as could be detected by FTIR, but identical compositions of their cores. Two of the POFs are exposed as cables (core, cladding and jacket) for about 3300 hours to the climate 92 °C / 95 % relative humidity (RH) resulting in a different transmission decrease. Investigating the related unexposed and exposed bare POFs for degradation using CL, FTIR, thermogravimetry (TG), UV/visible transmittance and gel permeation chromatography (GPC) suggest that claddings of POFs are more affected than cores. Probably the observed loss of transmission is mainly due to increased light absorption and imperfections at the core-cladding boundary caused by a large degradation of claddings. Hence, it is highly possible that the optical transmission stability of POFs is governed mainly by the thermo-oxidative stability of the cladding and minor of the core. Three bare POFs (core and cladding only) are exposed for different duration of exposure time (30 hours to 4500 hours) to 92 °C / 95 %RH, 92 °C / 50 %RH, 50 °C / 95 %RH, 90 °C / low humidity, 100 °C / low humidity, 110 °C / low humidity and 120 °C / low humidity. In these climates their transmission variations are found to be different from each other, too. The outcomes strongly inform that under high temperature and high humid climates physical changes such as volume expansion, are the main sources for the loss of optical transmission. Also, the optical transmission stability of POFs is found to be dependent on chemical compositions of claddings. Under high temperature and low humid conditions, a loss of transmission at the early stages of the exposure is mainly caused by physical changes, presumable by corecladding interface imperfections. For the later stages of exposures it is proposed to an additional increase of light absorption by core and cladding owes to degradation. Optical simulation results obtained parallel by Mr. L. Jankowski (a PhD student of BAM) are found to confirm these results. For bare POFs, too, the optical stability of POFs seems to depend on their thermo-oxidative stability. Some short-term exposure tests are conducted to realize influences of individual climatic parameters on the transmission property of POFs. It is found that at stationary high temperature and variable humidity conditions POFs display to a certain amount a reversible transmission loss due to physically absorbed water. But in the case of varying temperature and constant high humidity such reversibility is hardly noticeable. However, at room temperature and varying humidity, POFs display fully reversible transmission loss. The whole research described above has to be regarded as a starting point for further investigations. The restricted distribution of fundamental POF data by the manufacturers and the time consuming aging by climatic exposures restrict the results more or less to the samples, investigated here. Significant general statements require for example additional information concerning the variation of POF properties due to production. Nevertheless the tests, described here, have the capability for approximating and forecasting the long-term optical transmission stability of POFs. -------------- Auch im Druck erschienen: Appajaiah, Anilkumar: Climatic stability of polymer optical fibers (POF) / Anilkumar Appajaiah. - Bremerhaven : Wirtschaftsverl. NW, Verl. für neue Wiss., 2005. - Getr. Zählung [ca. 175 S.]. : Ill., graph. Darst. - (BAM-Dissertationsreihe ; 9) ISBN 3-86509-302-7 T2 - Climatic stability of polymer optical fibers (POF) KW - POF; Reliabilität; Abbau; Chemilumineszenz KW - POF; reliability; degradation; chemiluminescence Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0001661 ER - TY - THES A1 - Asfaw, Mesfin T1 - Adhesion of multi-component membbranes and strings Y1 - 2005 CY - Potsdam ER - TY - THES A1 - Ast, Cindy T1 - Design and photophysical characterization of single fluorophore-based ammonium sensors Y1 - 2013 CY - Potsdam ER - TY - THES A1 - Ast, Sandra T1 - Integration of the 1,2,3-Triazole "Click" motif as a potent signalling element into metal ion responsive fluorescent probes for physiological cations Y1 - 2012 CY - Potsdam ER - TY - THES A1 - Award, Duhan Jawad T1 - Mixed 1,2-Dümine-1,2-Dithiolate Ligand Complexes : Structure, Proberties and EPR Spectroscopy Y1 - 2009 CY - Potsdam ER - TY - THES A1 - Ba, Jianhua T1 - Nonaqueous synthesis of metal oxide nanoparticles and their assembly into mesoporous materials T1 - Nichtwässrige Synthese von Metalloxid-Nanopartikeln und deren Anordnung zu mesoporösen Materialien N2 - This thesis mainly consist of two parts, the synthesis of several kinds of technologically interesting crystalline metal oxide nanoparticles via nonaqueous sol-gel process and the formation of mesoporous metal oxides using some of these nanoparticles as building blocks via evaporation induced self-assembly (EISA) technique. In the first part, the experimental procedures and characterization results of successful syntheses of crystalline tin oxide and tin doped indium oxide (ITO) nanoparticles are reported. SnO2 nanoparticles exhibit monodisperse particle size (3.5 nm in average), high crystallinity and particularly high dispersibility in THF, which enable them to become the ideal particulate precursor for the formation of mesoporous SnO2. ITO nanoparticles possess uniform particle morphology, narrow particle size distribution (5-10 nm), high crystallinity as well as high electrical conductivity. The synthesis approaches and characterization of various mesoporous metal oxides, including TiO2, SnO2, mixture of CeO2 and TiO2, mixture of BaTiO3 and SnO2, are reported in the second part of this thesis. Mesoporous TiO2 and SnO2 are presented as highlights of this part. Mesoporous TiO2 was produced in the forms of both films and bulk material. In the case of mesoporous SnO2, the study was focused on the high order of the porous structure. All these mesoporous metal oxides show high crystallinity, high surface area and rather monodisperse pore sizes, which demonstrate the validity of EISA process and the usage of preformed crystalline nanoparticles as nanobuilding blocks (NBBs) to produce mesoporous metal oxides. N2 - Diese Arbeit besteht hauptsächlich aus zwei Teilen. Der erste Teil befasst sich mit der Synthese von mehreren technologisch wichtigen, kristallinen Metalloxid-Nanopartikeln mittels nichtwässriger Sol-Gel Chemie. Der zweite Teil beinhaltet die Herstellung von mesoporösen Metalloxiden. Dabei wurden ausgewählte Nanopartikel als Bausteine verwendet und durch langsames Verdampfen des Lösungsmittels in die entsprechenden porösen Strukturen überführt. Das experimentelle Vorgehen wie auch die Charakterisierung der erfolgreich hergestellten Zinnoxid- und Indiumzinnoxid-Nanopartikel sind im ersten Teil beschrieben. Die Zinnoxid-Nanpartikel zeichnen sich durch einheitliche Partikelgrösse (im Durchschnitt ca. 3.5 nm), hoher Kristallinität, und guter Dispergierbarkeit in Tetrahydrofuran aus. Diese Eigenschaften machen aus den Zinnoxid-Nanopartikeln die perfekten Bausteine für den Aufbau von mesoporösem Zinnoxid. Die Indiumzinnoxid-Nanopartikel haben eine einheitliche Partikelform, eine schmale Grösseverteilung (5-10 nm), hohe Kristallinität wie auch gute elektrische Leitfähigkeit. Die Synthese und Charakterisierung von verschiedenen mesoporösen Metalloxiden wie TiO2, SnO2, Mischungen von CeO2 und TiO2, wie auch Mischungen von BaTiO3 und SnO2 werden im zweiten Teil der Arbeit diskutiert. Mesoporöses TiO2 und SnO2 werden als besonders gelungene Beispiele herausgehoben. Mesoporöses TiO2 wurde in Form von Dünnfilmen wie auch als Bulkmaterial hergestellt. Im Falle von SnO2 galt das Augenmerk vor allem der hohen Ordnung der Mesoporen. Alle diese mesoporösen Materialien zeigen eine hohe Kristallinität, grosse Oberfläche und relativ einheitliche Porengrössen. Diese Eigenschaften unterstreichen, wie wertvoll der Ansatz ist, vorgeformte Nanopartikel als Bausteine für die Synthese von porösen Materialien zu verwenden. KW - Nanopartikel KW - transparent-leitendes Oxid KW - Selbstorganisation KW - nanoparticles KW - oxides KW - assembly KW - mesostructure Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-10173 ER - TY - THES A1 - Bahrke, Sven T1 - Mass spectrometric analysis of chitooligosaccharides and their interaction with proteins T1 - Massenspektrometrische Analyse von Chitooligosacchariden und ihre Wechselwirkungen mit Proteinen N2 - Chitooligosaccharides are composed of glycosamin and N-acetylglycisamin residues. Gel permeations chromatography is employed for the separation of oligomers, cation exchange chromatography is used for the separation of homologes and isomers. Trideuterioacetylation of the chitooligosaccharides followed by MALDI-TOF mass spectrometry allowes for the quantitation of mixtures of homologes. vMALDI LTQ multiple-stage MS is employed for quantitative sequencing of complex mixtures of heterochitooligosaccharides. Pure homologes and isomers are applied to biological assays. Chitooligosaccahrides form high-affinity non-covalent complexes with HC gp-39 (human cartilage glycoprotein of 39 kDa). The affinity of the chitooligosaccharides depends on DP, FA and the sequence of glycosamin and N-acetylglycosamin moieties. (+)nanoESI Q TOF MS/MS is used for identification of a high-affinity binding chitooligosaccharide of a non-covalent chitinase B - chitooligosaccharide complex. DADAA is identified as the heterochitoisomer binding with highest affinity and biostability to HC gp-39. Fluorescence based enzyme assays confirm the results. N2 - Chitooligosaccharide sind aus Glycosamin und N-Acetylglycosamun aufgebaut. Gelpermeationschromatographie wird für die Trennung von Oligomeren verwendet, die Kationenaustauschchromatographie wird zur Trennung von homologen- und Isomerengemischen angewendet. Trideuterioacetylierung der Chitooligosaccharide gefolgt von einer Analyse mittels MALDI-TOF MS erlaubt die quantitative Analyse von Homologengemischen. vMALDI LTQ multiple-stage MS wird angewendet zur Sequenzanalyse und Quantifizierung komplexer Gemische von Heterochitooligosacchariden. Reine Homologe und Isomere werden für biologische Assays verwendet. Dabei zeigt sich, dass Chitooligosaccharide mit HC gp-39 hochaffine Komplexe bilden. Die Affinität der Chitooligosaccharide hängt vom DP, FA und der Sequenz der Chitooligosaccharide ab. (+)nanoESI Q TOF MS/MS wird erfolgreich angewendet zur Identifizierung eines Chitooligosaccharides, das mit hoher Affinität an Chitinase B (Serratia marcescens) bindet. DADAA wurde als die Sequenz des Isomers identifiziert, das mit höchster Affinität und Biostabilität an aktive Chitinase B bindet. Fluoreszenz basierte Enzymassays konnten dieses Ergebnis bestätigen. KW - Chitooligosaccharide KW - HPLC KW - Massenspektrometrie KW - Chitolektine KW - Chitinase KW - Chitooligosaccharides KW - HPLC KW - Mass Spectrometry KW - Chitolectins KW - Chitinase Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-20179 ER - TY - THES A1 - Bahrke, Sven A1 - Einarsson, Jon M. A1 - Gislason, Johannes A1 - Haebel, Sophie A1 - Peter-Katalinic, Jasna A1 - Peter, Martin G. T1 - Characterization of chitooligosaccharides by mass spectrometry Y1 - 2003 SN - 82-47-15901-5 ER - TY - THES A1 - Bai, Shuo T1 - Active hydrogels with nanocomposites Y1 - 2010 CY - Potsdam ER - TY - THES A1 - Baryzewska, Agata W. T1 - Reconfigurable Janus emulsions as signal transducers for biosensing applications Y1 - 2023 ER - TY - THES A1 - Bastian, Philipp U. T1 - Core-shell upconversion nanoparticles - investigation of dopant intermixing and surface modification T1 - Kern-Schale Aufkonvertierende Nanopartikel — eine Untersuchung der Dotandenvermischung und Oberflächenmodifikation N2 - Frequency upconversion nanoparticles (UCNPs) are inorganic nanocrystals capable to up-convert incident photons of the near-infrared electromagnetic spectrum (NIR) into higher energy photons. These photons are re-emitted in the range of the visible (Vis) and even ultraviolet (UV) light. The frequency upconversion process (UC) is realized with nanocrystals doped with trivalent lanthanoid ions (Ln(III)). The Ln(III) ions provide the electronic (excited) states forming a ladder-like electronic structure for the Ln(III) electrons in the nanocrystals. The absorption of at least two low energy photons by the nanoparticle and the subsequent energy transfer to one Ln(III) ion leads to the promotion of one Ln(III) electron into higher excited electronic states. One high energy photon will be emitted during the radiative relaxation of the electron in the excited state back into the electronic ground state of the Ln(III) ion. The excited state electron is the result of the previous absorption of at least two low energy photons. The UC process is very interesting in the biological/medical context. Biological samples (like organic tissue, blood, urine, and stool) absorb high-energy photons (UV and blue light) more strongly than low-energy photons (red and NIR light). Thanks to a naturally occurring optical window, NIR light can penetrate deeper than UV light into biological samples. Hence, UCNPs in bio-samples can be excited by NIR light. This possibility opens a pathway for in vitro as well as in vivo applications, like optical imaging by cell labeling or staining of specific organic tissue. Furthermore, early detection and diagnosis of diseases by predictive and diagnostic biomarkers can be realized with bio-recognition elements being labeled to the UCNPs. Additionally, "theranostic" becomes possible, in which the identification and the treatment of a disease are tackled simultaneously. For this to succeed, certain parameters for the UCNPs must be met: high upconversion efficiency, high photoluminescence quantum yield, dispersibility, and dispersion stability in aqueous media, as well as availability of functional groups to introduce fast and easy bio-recognition elements. The UCNPs used in this work were prepared with a solvothermal decomposition synthesis yielding in particles with NaYF4 or NaGdF4 as host lattice. They have been doped with the Ln(III) ions Yb3+ and Er3+, which is only one possible upconversion pair. Their upconversion efficiency and photoluminescence quantum yield were improved by adding a passivating shell to reduce surface quenching. However, the brightness of core-shell UCNPs stays behind the expectations compared to their bulk material (being at least μm-sized particles). The core-shell structures are not clearly separated from each other, which is a topic in literature. Instead, there is a transition layer between the core and the shell structure, which relates to the migration of the dopants within the host lattice during the synthesis. The ion migration has been examined by time-resolved laser spectroscopy and the interlanthanoid resonance energy transfer (LRET) in the two different host lattices from above. The results are presented in two publications, which dealt with core-shell-shell structured nanoparticles. The core is doped with the LRET-acceptor (either Nd3+ or Pr3+). The intermediate shell serves as an insulation shell of pure host lattice material, whose shell thickness has been varied within one set of samples having the same composition, so that the spatial separation of LRET-acceptor and -donor changes. The outer shell with the same host lattice is doped with the LRET-donor (Eu3+). The effect of the increasing insulation shell thickness is significant, although the LRET cannot be suppressed completely. Next to the Ln(III) migration within a host lattice, various phase transfer reactions were investigated in order to subsequently perform surface modifications for bioapplications. One result out of this research has been published using a promising ligand, that equips the UCNP with bio-modifiable groups and has good potential for bio-medical applications. This particular ligand mimics natural occurring mechanisms of mussel protein adhesion and of blood coagulation, which is why the UCNPs are encapsulated very effectively. At the same time, bio-functional groups are introduced. In a proof-of-concept, the encapsulated UCNP has been coupled successfully with a dye (which is representative for a biomarker) and the system’s photoluminescence properties have been investigated. N2 - Frequenzaufkonvertierende Nanopartikel (UCNP) sind anorganische Nanokristalle. Sie können einfallende Photonen des nah-infraroten elektromagnetischen Spektrums (NIR) in höher energetische Photonen im Bereich des sichtbaren Lichtes und sogar des ultravioletten Lichtes (UV) umwandeln und wieder emittieren. Dieser Frequenzaufkonversionsprozess (UC) basiert auf Nanokristallen, die mit dreiwertigen Lanthanoid-Ionen (Ln(III)) dotiert sind. Die elektronisch angeregten Zustände der Ln(III)-Ionen stehen zur Verfügung, mit deren Hilfe Elektronen über eine leiterartige elektronische Struktur der elektronischen Zustände der Ln(III)-Ionen in höher angeregte Zustände gelangen können. Zuvor müssen mindestens zwei niederenergetische Photonen vom Nanopartikel absorbiert werden. Die absorbierte Energie muss über einen oder mehrere Energieübertragungen das gleiche Ln(III)-Ion erreichen um beim strahlenden Relaxieren des Elektrones im angeregten Zustand zurück in den elektronischen Grundzustand des Ln(III)-Ions ein höherenergetisches Photon zu emittieren. Der Frequenzaufkonversionsprozess ist sehr interessant für die Anwendung im biologisch/medizinischen Bereich. Biologische Proben (z.B. organisches Gewebe, Blut, Urin und Stuhl) absorbieren höherenergetische Photonen (UV) stärker als niederenergetische Photonen (NIR). Dank eines natürlich vorkommenden optischen Fensters in biologischen Proben kann NIR-Licht tiefer als UV-Licht eindringen, sodass die UCNPs in biologischen Proben mit NIR-Licht angeregt werden können. Dies ermöglicht in vitro als auch in vivo Anwendungen, z.B. für die optische Bildgebung durch Markieren von Zellen oder durch Einfärben von bestimmten Bereichen organischer Gewebe. Frühzeitige Erkennung von Krankheiten kann durch prädiktive und diagnostisch geeignete Biomarker, die mit Erkennungselementen an den UCNPs detektiert werden, realisiert werden. Demnach ist „Theranostic“ ein mögliches Szenario, das die Identifikation und die gleichzeitige Behandlung einer Krankheit ermöglichen könnte. Um diese Vision zu realisieren, müssen die UCNPs bestimmte Parameter erfüllen: Eine hohe Aufkonversionseffizienz, eine hohe Photolumineszenzquantenausbeute, eine gute Dispergierbarkeit und Stabilität der Dispersion in wässrigen Medien, sowie die Verfügbarkeit von funktionellen Gruppen, um schnell und einfach biologische Erkennungselemente daran zu koppeln. Die UCNPs dieser Arbeit wurden mit Hilfe einer solvothermalen Zersetzungsreaktion durchgeführt. Die Nanopartikel bestanden aus unterschiedlichen Wirtsgittern, entweder aus NaYF4 oder NaGdF4. Die Wirtsgitter wurden mit den Ln(III)-Ionen Yb3+ und Er3+ dotiert. Die Aufkonversionseffizienz, somit auch deren Quantenausbeute, konnte mit einer passivierenden Schale verbessert werden. Dennoch leuchten die Kern-Schale-UCNPs schlechter als es im Vergleich mit μm-großen Partikeln zu erwarten wäre. Die Kern-Schale-Strukturen gehen ineinander über und sind nicht klar voneinander getrennt. Zwischen dem Kern und der Schale existiert eine Übergangsregion, die mit der Wanderung der Ionen des Wirtsgitters und den dotierten Ln(III)-Ionen einhergeht. Diese Beobachtung wird auch in der Literatur diskutiert. Die Ionenwanderung wurde mit Hilfe von zeitaufgelöster Laserspektroskopie und dem Interlanthanoidenergietransfer (LRET) in den beiden erwähnten Wirtsgittern untersucht. Die Ergebnisse sind in zwei Publikationen veröffentlicht, die auf Kern-Schale-Schale-Strukturen basieren. Der Kern ist mit dem LRET-Akzeptor dotiert (Nd3+ oder Pr3+). Die Zwischenschale besteht aus dem gleichen Wirtsgitter ohne Dotierstoffe und dient als Isolationsschale, deren Schalendicke innerhalb einer Experimentierreihe variiert wurde, um eine räumliche Trennung von LRET-Akzeptor und -Donor zu schaffen. Die äußere Schale, aus dem gleichen Wirtsgitter, ist mit dem LRET-donor (Eu3+) dotiert. Der Effekt der wachsenden Isolationsschalendicke ist signifikant. Aber es ist nicht möglich gewesen, den Energietransfer vom Donor auf den Akzeptor komplett zu unterbinden. Neben der Untersuchung der Wanderung von Ln(III)-Ionen in einem Wirtsgitter wurden verschiedene Phasentransferreaktionen durchgeführt, um anschließende Oberflächenmodifikationen anzuwenden, damit die Anwendungen der UCNPs im biologischen Kontext prinzipiell demonstriert werden kann. Ein Ergebnis mit einem sehr vielversprechenden Liganden für die bio-medizinische Anwendung wurde in einer Publikation veröffentlicht. Dieser Ligand imitiert natürliche Mechanismen von Muschelproteinen und von Blutkoagulation, sodass die untersuchten Nanopartikel sehr effektiv eingekapselt werden. Gleichzeitig sind funktionelle Gruppen zur Bio-Funktionalisierung vorhanden. In einer Machbarkeitsstudie wurde der eingekapselte UCNP erfolgreich mit einem Farbstoff (der durch einen Biomarker ersetzt werden kann) gekoppelt und die Photolumineszenzeigenschaften des Systems untersucht. KW - upconversion KW - Aufkonversion KW - Nanopartikel KW - nanoparticle KW - bio-modification KW - Biomodification KW - Ionenmigration KW - ion migration KW - surface modification KW - Oberflächenmodifizierung Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-551607 ER - TY - THES A1 - Behrendt, Felix Nicolas T1 - New bio-based polymers T1 - Neue biobasierte Polymere BT - synthesis and polymerization of cystine-based macrocycles BT - Synthese und Polymerisation von cystinbasierten Makrozyklen N2 - Redox-responsive polymers, such as poly(disulfide)s, are a versatile class of polymers with potential applications including gene- and drug-carrier systems. Their degradability under reductive conditions allows for a controlled response to the different redox states that are present throughout the body. Poly(disulfide)s are typically synthesized by step growth polymerizations. Step growth polymerizations, however, may suffer from low conversions and therefore low molar masses, limiting potential applications. The purpose of this thesis was therefore to find and investigate new synthetic routes towards the synthesis of amino acid-based poly(disulfide)s. The different routes in this thesis include entropy-driven ring opening polymerizations of novel macrocyclic monomers, derived from cystine derivatives. These monomers were obtained with overall yields of up to 77% and were analyzed by mass spectrometry as well as by 1D and 2D NMR spectroscopy. The kinetics of the entropy-driven ring-opening metathesis polymerization (ED-ROMP) were thoroughly investigated in dependence of temperature, monomer concentration, and catalyst concentration. The polymerization was optimized to yield poly(disulfide)s with weight average molar masses of up to 80 kDa and conversions of ~80%, at the thermodynamic equilibrium. Additionally, an alternative metal free polymerization, namely the entropy-driven ring-opening disulfide metathesis polymerization (ED-RODiMP) was established for the polymerization of the macrocyclic monomers. The effect of different solvents, concentrations and catalyst loadings on the polymerization process and its kinetics were studied. Polymers with very high weight average molar masses of up to 177 kDa were obtained. Moreover, various post-polymerization reactions were successfully performed. This work provides the first example of the homopolymerization of endo-cyclic disulfides by ED-ROMP and the first substantial study into the kinetics of the ED-RODiMP process. N2 - Redoxresponsive Polymere, wie etwa Polydisulfide, sind eine vielseitige Klasse von Polymeren, die unter anderem als Gen- und Wirkstoffträgersysteme eingesetzt werden können. Ihre Abbaubarkeit unter reduktiven Bedingungen ermöglicht eine kontrollierte Reaktion auf die verschiedenen Redoxzustände im Körper. Polydisulfide werden jedoch häufig durch Stufenwachstums-polymerisationen synthetisiert. Diese führen oft zu niedrigen Umsätzen und daher zu niedrigen molaren Massen. Das Ziel dieser Arbeit war daher neue Synthesewege für aminosäurebasierte Polydisulfide zu finden und zu untersuchen. Diese Wege beinhalteten entropiegetriebene ringöffnende Polymerisationen von neuen makrozyklischen Monomeren, auf der Basis von Cystin-Derivaten. Diese Monomere konnten mit einer Gesamtausbeute von bis zu 77% synthetisiert werden und wurden mit Massenspektrometrie sowie mit 1D- und 2D-NMR-Spektroskopie analysiert. Die Kinetik der entropiegetriebenen ringöffnenden Metathese Polymerisation (ED-ROMP) wurde im Hinblick auf Temperatur, Monomerkonzentration und Katalysatormenge sorgfältig untersucht. Durch Optimierungen konnten Polydisulfide mit gewichtsmittleren Molmassen von bis zu 80 kDa und Umsätzen von ~80%, im thermodynamischen Gleichgewicht synthetisiert werden. Zusätzlich wurde eine alternative metallfreie Polymerisation, die entropiegetriebene ringöffnende Disulfidmetathese Polymerisation (ED-RODiMP), für die Polymerisation der makrozyklischen Monomere etabliert. Die Auswirkungen verschiedener Lösungsmittel, Konzentrationen und Katalysatorkonzentrationen auf die Kinetik dieses Polymerisationsprozesses wurden untersucht. Hierdurch wurden Polymere mit sehr hohen gewichtsmittleren Molmassen von bis zu 177 kDa erhalten. Darüber hinaus wurden verschiedene Postpolymerisationsreaktionen erfolgreich durchgeführt. Diese Arbeit liefert das erste Beispiel für die Homopolymerisation endo-zyklischer Disulfide durch ROMP und eine erste substanzielle Studie der Kinetik des ED-RODiMP-Prozesses. KW - polymers KW - ADMET KW - ROMP KW - disulfide KW - macrocycles KW - ring-opening polymerization KW - amino acids KW - Polymere KW - ADMET KW - ROMP KW - Disulfide KW - Makrozyklen KW - ringöffnende Polymerisation KW - Aminosäuren Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-418316 ER - TY - THES A1 - Bellin, Ingo T1 - Thermosensitive Polymer Networks with Two Different Shapes in Memory Y1 - 2006 CY - Potsdam ER - TY - THES A1 - Belova, Valentina T1 - Composite fabrication and surface modification via high intensity ultrasound Y1 - 2010 CY - Potsdam ER - TY - THES A1 - Berg, John K. T1 - Size-dependent wetting behavior of organic molecules on solid surfaces Y1 - 2011 CY - Potsdam ER - TY - THES A1 - Bettenbühl, Mario T1 - Microsaccades: symbols in fixational eye movements Y1 - 2012 CY - Potsdam ER - TY - THES A1 - Beyvers, Stephanie T1 - Selective excitation of adsorbate vibrations on dissipative surfaces T1 - Selektive Anregung von Adsorbatschwingungen auf dissipativen Oberflächen N2 - The selective infrared (IR) excitation of molecular vibrations is a powerful tool to control the photoreactivity prior to electronic excitation in the ultraviolet / visible (UV/Vis) light regime ("vibrationally mediated chemistry"). For adsorbates on surfaces it has been theoretically predicted that IR preexcitation will lead to higher UV/Vis photodesorption yields and larger cross sections for other photoreactions. In a recent experiment, IR-mediated desorption of molecular hydrogen from a Si(111) surface on which atomic hydrogen and deuterium were co-adsorbed was achieved, following a vibrational mechanism as indicated by the isotope-selectivity. In the present work, selective vibrational IR excitation of adsorbate molecules, treated as multi-dimensional oscillators on dissipative surfaces, has been simulated within the framework of open-system density matrix theory. Not only potential-mediated, inter-mode coupling poses an obstacle to selective excitation but also the coupling of the adsorbate ("system") modes to the electronic and phononic degrees of freedom of the surface ("bath") does. Vibrational relaxation thereby takes place, depending on the availabilty of energetically fitting electron-hole (e/h) pairs and/or phonons (lattice vibrations) in the surface, on time-scales ranging from milliseconds to several hundreds of femtoseconds. On metal surfaces, where the relaxation process of the adsorbate via the e/h pair mechanism dominates, vibrational lifetimes are usually shorter than on insulator or semiconductor surfaces, in the range of picoseconds, being also the timescale of the IR pulses used here. Further inhibiting factors for selectivity can be the harmonicity of a mode and weak dipole activities ("dark modes") rendering vibrational excitation with moderate field intensities difficult. In addition to simple analytical pulses, optimal control theory (OCT) has been employed here to generate a suitable electric field to populate the target state/mode maximally. The complex OCT fields were analyzed by Husimi transformation, resolving the control field in time and energy. The adsorbate/surface systems investigated were CO/Cu(100), H/Si(100) and 2H/Ru(0001). These systems proved to be suitable models to study the above mentioned effects. Further, effects of temperature, pure dephasing (elastic scattering processes), pulse duration and dimensionality (up to four degrees of freedom) were studied. It was possible to selectively excite single vibrational modes, often even state-selective. Special processes like hot-band excitation, vibrationally mediated desorption and the excitation of "dark modes" were simulated. Finally, a novel OCT algorithm in density matrix representation has been developed which allows for time-dependent target operators and thus enables to control the excitation mechanism instead of only the final state. The algorithm is based on a combination of global (iterative) and local (non-iterative) OCT schemes, such that short, globally controlled time-intervals are coupled locally in time. Its numerical performance and accuracy were tested and verified and it was successfully applied to stabilize a two-state linear-combination and to enforce a successive "ladder climbing" in a rather harmonic system, where monochromatic, analytical pulses simultaneously excited several states, leading to a population loss in the target state. N2 - Die selektive Anregung von Molekülschwingungen mittels Infrarotlicht (IR) ist vorteilhaft, um die Wirkungsquerschnitte nachfolgender photochemischer oder photophysikalischer Prozesse zu steigern, welche durch Elektronenanregung mittels ultraviolettem (UV) bzw. sichtbarem (Vis) Licht ausgelöst werden. Für Adsorbatmoleküle auf Oberflächen wurden theoretische Vorhersagen getroffen, dass eine kombinierte (IR plus UV)-Strategie ("schwingungsvermittelte Chemie") die Ausbeute bei Photodesorption und anderen Photoreaktionen deutlich zu erhöhen vermag. Kürzlich wurde im Experiment gezeigt, dass eine rein IR-vermittelte Desorption möglich ist, welche über einen schwingungsangeregten Mechanismus erfolgt. Hierbei wurde molekularer Wasserstoff von einer Si(111)-Oberfläche desorbiert, an der atomarer Wasserstoff und atomares Deuterium gebunden waren. Eine thermische Anregung, die zum Bindungsbruch führt, konnte hierbei wegen der Isotopenselektivität ausgeschlossen werden. In der vorliegenden Arbeit wurde die selektive IR-Schwingungsanregung von Adsorbaten, die als multidimensionale Oszillatoren auf dissipativen Oberflächen behandelt wurden, mit Hilfe der Dichtematrixtheorie für offene Systeme simuliert. Nicht nur die potentialvermittelte Kopplung zwischen den einzelnen Moden ist ein Hindernis für selektive Anregung, sondern auch die Kopplung der Moden des Adsorbats ("Systems") an elektronische und phononische Freiheitsgrade des Substrats ("Bades"). Die Schwingungsrelaxation verläuft hierbei auf Zeitskalen, die von Millisekunden bis hin zu wenigen hundert Femtosekunden reichen, je nach Verfügbarkeit energetisch geeigneter Elektron-Loch-Paar-Anregungen bzw. Phononen (Gitterschwingungen) in der Oberfläche. Auf Metalloberflächen, bei denen die Schwingungrelaxation des Adsorbats zumeist von einem Elektronen-Loch-Paar-Mechanismus dominiert wird, sind die Schwingungslebensdauern normalerweise kürzer als auf Isolator- oder Halbleiteroberflächen und betragen einige Picosekunden, ebenso wie die Zeitskala der hier gewählten IR-Pulse. Weitere Faktoren, die die selektive Anregung behindern können sind die Harmonizität einer Mode und die geringe Dipolaktivität sogenannter "dunkler Moden", die eine Anregung mit moderat intensiven Feldern erschweren. Zusätzlich zu einfachen analytischen Pulsen wurden Felder mittels Optimaler Kontrolltheorie (OCT) erzeugt, um eine(n) Zielzustand/-mode maximal zu populieren. Komplexe OCT Pulse wurden mit Hilfe der Husimi-Transformation analysiert, welche das Kontrollfeld im Zeit- und Energieraum aufzulösen vermag. Die in dieser Arbeit untersuchten Adsorbat/Oberflächen-Systeme waren CO/Cu(100), H/Si(100) und 2H/Ru(0001), die sich als passende Modelle erwiesen, um oben genannte Faktoren zu untersuchen. Desweiteren wurden die Auswirkungen von Temperatur, reiner Dephasierung (elastische Streuprozesse), Dauer des IR-Pulses und Systemdimensionalit\"at (Behandlung von bis zu vier Freiheitsgraden) studiert. Einzelne Schwingungsmoden konnten angeregt werden, in vielen Fällen sogar zustandsselektiv. Spezielle Prozesse wie die Anregung "heißer Banden", Desorption via alleiniger Schwingungsanregung und die Anregung "dunkler Moden" wurden simuliert. Schließlich wurde ein neuer OCT-Algorithmus in Dichtematrixdarstellung entwickelt, der es erlaubt, zeitabhängige Zieloperatoren einzuführen, um nicht nur Kontrolle über den Endzustand einer Anregung, sondern auch über den Anregungsmechanismus zu erlangen. Der Algorithmus basiert auf einer Kombination von globaler (iterativer) und lokaler (nicht-iterativer) optimaler Kontrollschemata in der Art, dass kurze, global kontrollierte Intervalle zeitlich lokal miteinander gekoppelt werden. Nach numerischen Tests wurde der Algorithmus erfolgreich angewandt, um eine Linearkombination aus zwei Zuständen zu stabilisieren, sowie um eine schrittweise "Leiteranregung" in einem harmonischen System zu forcieren, bei dem monochromatische, analytische Pulse mehrere Zustände zugleich anregen und somit einen Populationsverlust im angestrebten Zielzustand zur Folge haben. KW - IR-Anregung KW - Selektivität KW - Adsorbatschwingungen KW - Dichtematrixtheorie offener Systeme KW - Optimale Kontrolltheorie KW - IR excitation KW - selectivity KW - adsorbate vibrations KW - open system density matrix theory KW - optimal control theory Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-25516 ER - TY - THES A1 - Bhaskar, Thanga Bhuvanesh Vijaya T1 - Biomimetic layers of extracellular matrix glycoproteins as designed biointerfaces N2 - The goal of regenerative medicine is to guide biological systems towards natural healing outcomes using a combination of niche-specific cells, bioactive molecules and biomaterials. In this regard, mimicking the extracellular matrix (ECM) surrounding cells and tissues in vivo is an effective strategy to modulate cell behaviors. Cellular function and phenotype is directed by the biochemical and biophysical signals present in the complex 3D network of ECMs composed mainly of glycoproteins and hydrophilic proteoglycans. While cellular modulation in response to biophysical cues emulating ECM features has been investigated widely, the influence of biochemical display of ECM glycoproteins mimicking their presentation in vivo is not well characterized. It remains a significant challenge to build artificial biointerfaces using ECM glycoproteins that precisely match their presentation in nature in terms of morphology, orientation and conformation. This challenge becomes clear, when one understands how ECM glycoproteins self-assemble in the body. Glycoproteins produced inside the cell are secreted in the extra-cellular space, where they are bound to the cell membrane or other glycoproteins by specific interactions. This leads to elevated local concentration and 2Dspatial confinement, resulting in self-assembly by the reciprocal interactions arising from the molecular complementarity encoded in the glycoprotein domains. In this thesis, air-water (A-W) interface is presented as a suitable platform, where self-assembly parameters of ECM glycoproteins such as pH, temperature and ionic strength can be controlled to simulate in vivo conditions (Langmuir technique), resulting in the formation of glycoprotein layers with defined characteristics. The layer can be further compressed with surface barriers to enhance glycoprotein-glycoprotein contacts and defined layers of glycoproteins can be immobilized on substrates by horizontal lift and touch method, called Langmuir-Schäfer (LS) method. Here, the benefit of Langmuir and LS methods in achieving ECM glycoprotein biointerfaces with controlled network morphology and ligand density on substrates is highlighted and contrasted with the commonly used (glyco)protein solution deposition (SO) method on substrates. In general, the (glyco)protein layer formation by SO is rather uncontrolled, influenced strongly by (glyco)protein-substrate interactions and it results in multilayers and aggregations on substrates, while the LS method results in (glyco)proteins layers with a more homogenous presentation. To achieve the goal of realizing defined ECM layers on substrates, ECM glycoproteins having the ability to self-assemble were selected: Collagen-IV (Col-IV) and fibronectin (FN). Highly packed FN layer with uniform presentation of ligands was deposited on polydimethysiloxane VIII (PDMS) by LS method, while a heterogeneous layer was formed on PDMS by SO with prominent aggregations visible. Mesenchymal stem cells (MSC) on PDMS equipped with FN by LS exhibited more homogeneous and elevated vinculin expression and weaker stress fiber formation than on PDMS equipped with FN by SO and these divergent responses could be attributed to the differences in glycoprotein presentation at the interface. Col-IV are scaffolding components of specialized ECM called basement membranes (BM), and have the propensity to form 2D networks by self-polymerization associated with cells. Col- IV behaves as a thin-disordered network at the A-W interface. As the Col-IV layer was compressed at the A-W interface using trough barriers, there was negligible change in thickness (layer thickness ~ 50 nm) or orientation of molecules. The pre-formed organization of Col-IV was transferred by LS method in a controlled fashion onto substrates meeting the wettability criterion (CA ≤ 80°). MSC adhesion (24h) on PET substrates deposited with Col-IV LS films at 10, 15 and 20 mN·m-1 surface pressures was (12269.0 ± 5856.4) cells for LS10, (16744.2 ± 1280.1) cells for LS15 and (19688.3 ± 1934.0) cells for LS20 respectively. Remarkably, by selecting the surface areal density of Col-IV on the Langmuir trough on PET, there is a linear increase between the number of adherent MSCs and the Col-IV ligand density. Further, FN has the ability to self-stabilize and form 2D networks (even without compression) while preserving native β-sheet structure at the A-W interface on a defined subphase (pH = 2). This provides the possibility to form such layers on any vessel (even on standard six-well culture plates) and the cohesive FN layers can be deposited by LS transfer, without the need for expensive LB instrumentation. Multilayers of FN can be immobilized on substrates by this approach, as easily as Layer-by-Layer method, even without the need for secondary adlayer or activated bare substrate. Thus, this facile glycoprotein coating strategy approach is accessible to many researchers to realize defined FN films on substrates for cell culture. In conclusion, Langmuir and LS methods can create biomimetic glycoprotein biointerfaces on substrates controlling aspects of presentation such as network morphology and ligand density. These methods will be utilized to produce artificial BM mimics and interstitial ECM mimics composed of more than one ECM glycoprotein layer on substrates, serving as artificial niches instructing stem cells for cell-replacement therapies in the future. N2 - Ziel der regenerativen Medizin ist es, Regenerationsprozesse in biologischen Systemen mit Hilfe von nischenspezifischen Zellen, bioaktiven Molekülen und Biomaterialien zu modulieren. In diesem Zusammenhang ist die Nachahmung der extrazellulären Matrix (ECM), die Zellen und Gewebe in vivo umgibt, eine wirksame Strategie zur Modulation des Zellverhaltens. Die zelluläre Funktion und der Phänotyp werden durch die biochemischen und biophysikalischen Signale gesteuert, die in dem komplexen 3D-Netzwerk von ECMs vorhanden sind, welches hauptsächlich aus Glykoproteinen und hydrophilen Proteoglykanen besteht. Während die zelluläre Modulation als Reaktion auf biophysikalische Signale, die ECM-Merkmale nachahmen, umfassend untersucht wurde, ist der Einfluss der biochemischen Charakterisierung von ECM-Glykoproteinen, die deren Darstellung in vivo nachahmen, nicht gut charakterisiert. Es bleibt eine bedeutende Herausforderung, künstliche Biogrenzflächen mit ECM-Glykoproteinen zu schaffen, die in Bezug auf Morphologie, Orientierung und Konformation genau ihrer Darstellung in der Natur entsprechen. Diese Herausforderung wird deutlich, wenn man versteht, wie sich die ECM-Glykoproteine im Körper selbst zusammensetzen. Glykoproteine, die im Inneren der Zelle produziert werden, werden im extrazellulären Raum ausgeschieden, wo sie durch spezifische Interaktionen an die Zellmembran oder andere Glykoproteine gebunden werden. Dies führt zu einer erhöhten lokalen Konzentration und zweidimensionalen Raumbegrenzung, was durch die wechselseitigen Wechselwirkungen, die sich aus der in den Glykoprotein-Domänen kodierten molekularen Komplementarität ergeben, zur Selbstorganisation führt. In dieser Arbeit wird die Luft-Wasser (A-W)-Grenzfläche als eine geeignete Umgebung vorgestellt, mit der die Selbstorganisationsparameter von ECM-Glykoproteinen wie pH-Wert, Temperatur und Ionenstärke kontrolliert werden können, um in vivo-Bedingungen zu simulieren (Langmuir-Technik), was zur Bildung von Glykoproteinschichten mit definierten Eigenschaften führt. Die Schicht kann mit Oberflächenbarrieren weiter komprimiert werden, um die Glykoprotein-Glykoprotein-Kontakte zu verstärken, und definierte Schichten von Glykoproteinen können auf Substraten durch eine horizontale Hebe- und Berührungsmethode, sie sogenannte Langmuir-Schäfer (LS)-Methode, immobilisiert werden. Hier wird der Vorteil der Langmuir- und LS-Methode bei der Erzielung von ECM-Glykoprotein-Biogrenzflächen mit kontrollierter Netzwerkmorphologie und Ligandendichte auf Oberflächen hervorgehoben und mit der üblicherweise verwendeten Methode der (Glyko)Protein-Lösungsabscheidung (SO) auf Oberflächen gegenübergestellt. Im Allgemeinen ist die (Glyko)ProteinX Schichtbildung durch SO eher unkontrolliert, wird stark durch (Glyko)Protein-Substrat- Wechselwirkungen beeinflusst und führt zu Mehrfachschichten und Ansammlungen auf Oberflächen, während die LS-Methode zu (Glyko)Protein-Schichten mit einer homogeneren Darstellung führt. Um definierte ECM-Schichten auf Oberflächen zu erzeugen, wurden ECM-Glykoproteine mit der Fähigkeit zur Selbstorganisation ausgewählt: Kollagen-IV (Col-IV) und Fibronektin (FN). Eine dicht gepackte FN-Schicht mit gleichmäßiger Verteilung der Liganden wurde mit der LSMethode auf Polydimethysiloxan (PDMS) aufgetragen, während auf PDMS mit SO eine heterogene Schicht mit klar erkennbaren Verdichtungen gebildet wurde. Mesenchymale Stammzellen (MSC) auf PDMS, denen FN nach der LS-Methode hinzugefügt wurde, wiesen eine homogenere und erhöhte Vinculin-Expression und eine schwächere Stressfaserbildung auf als MSC Stammzellen auf PDMS, dem FN nach der SO-Methode hinzugefügt wurde, und diese verschiedenen Reaktionen konnten auf die Unterschiede in der Glykoprotein-Verteilung an der Grenzfläche zurückgeführt werden. Col-IV ist eine Komponente spezialisierter ECMs, die Basalmembranen (BM) genannt werden, und neigen zur Bildung von 2D-Netzwerke durch Selbstpolymerisation, die mit Zellen assoziiert sind. Col-IV verhält sich wie ein dünnes ungeordnetes Netzwerk an der A-WGrenzfläche. Während die Col-IV-Schicht an der A-W-Grenzfläche mit Hilfe von Trogbarrieren zusammengerückt wurde, gab es eine vernachlässigbare Änderung der Dicke (Schichtdicke ~ 50 nm) oder der Orientierung der Moleküle. Die vorgeformte Organisation von Col-IV wurde mit der LS-Methode kontrolliert auf Oberflächen aufgetragen, die das Kriterium der Benetzbarkeit erfüllten (CA ≤ 80°). Die MSC-Adhäsion (24h) auf Polyethylenterephthalat (PET)-Oberflächen, die mit Col-IV LS-Folien bei Oberflächendrücken von 10, 15 und 20 mN·m-1 aufgebracht wurden, waren (12269,0 ± 5856,4) Zellen für LS10, (16744,2 ± 1280,1) Zellen für LS15 (19688,3 ± 1934,0) Zellen für LS20. Bemerkenswert ist dabei, dass durch die Auswahl der Oberflächen-Flächendichte von Col-IV am Langmuir-Trog auf PET ein linearer Anstieg zwischen der Anzahl der adhärenten MSCs und der Col-IV-Ligandendichte erfolgt. Auch FN die Fähigkeit, sich selbst zu stabilisieren und 2D-Netzwerke zu bilden (sogar ohne Kompression), während die native β-Faltblattstruktur an der A-W-Grenzfläche auf einer definierten Subphase (pH = 2) erhalten bleibt. Dies bietet die Möglichkeit, solche Schichten auf jedem beliebigen Gefäß (sogar auf Platten mit Standard-Six-Well-Kulturen) zu bilden, und die kohäsiven FN-Schichten können durch LS-Transfer abgelagert werden, ohne dass eine teure LB-Instrumentierung erforderlich ist. Mehrfachschichten aus FN können auf diese Weise XI auf Oberflächen immobilisiert werden, genauso einfach wie bei der Layer-by-Layer-Methode, auch ohne die Notwendigkeit einer zweiten adsorbierenden Schicht oder einer aktivierten blanken Oberfläche. Somit ist dieser Ansatz einer einfachen Glykoprotein- Beschichtungsstrategie vielen Forschern zugänglich, um definierte FN-Filme auf Oberflächen für die Zellkultur zu realisieren. Zusammenfassend lässt sich sagen, dass Langmuir- und LSMethoden biomimetische Glykoprotein-Bioschnittstellen auf Oberflächen erzeugen können, die makroskopische Darstellungen wie Netzwerkmorphologie und Ligandendichte kontrollieren. Diese Methoden werden genutzt, um künstliche BM und ECM zu generieren, die aus mehr als einer Glykoproteinschicht bestehen. Diese können dann als künstliche Nischen für Stammzellen, die in zukünftigen Zellersatztherapien zum Einsatz kommen könnte. KW - Extracellular Matrix KW - Biomimetics KW - Glycoproteins KW - Langmuir-Schaefer method KW - Designed Biointerfaces KW - Extrazelluläre Matrix KW - Biomimetik KW - Glykoproteine KW - Langmuir-Schäfer-Methode KW - Designte Biointerface Y1 - 2020 ER - TY - THES A1 - Bhattacharryya, Saroj Kumar T1 - Development of detector for analytical ultracentrifuge. - [korr. Fassung] T1 - Detektor-Entwicklung für die analytische Ultrazentrifuge. - [korr. Fassung] N2 - In this work approaches for new detection system development for an Analytical Ultracentrifuge (AUC) were explored. Unlike its counterpart in chromatography fractionation techniques, the use of a Multidetection system for AUC has not yet been implemented to full extent despite its potential benefit. In this study we tried to couple existing fundamental spectroscopic and scattering techniques that are used in day to day science as tool for extracting analyte information. Trials were performed for adapting Raman, Light scattering and UV/Vis (with possibility to work with the whole range of wavelengths) to AUC. Conclusions were drawn for Raman and Light scattering to be a possible detection system for AUC, while the development for a fast fiber optics based multiwavelength detector was completed. The multiwavelength detector demonstrated the capability of data generation matching the literature and reference measurement data and faster data collection than that of the commercial instrument. It became obvious that with the generation of data in 3-D space in the UV/Vis detection system, the user can select the wavelength for the evaluation of experimental results as the data set contains the whole range of information from UV/Vis wavelength. The detector showed the data generation with much faster speed unlike the commercial instruments. The advantage of fast data generation was exemplified with the evaluation of data for a mixture of three colloids. These data were in conformity with measurement results from normal radial experiments and without significant diffusion broadening. Thus conclusions were drawn that with our designed Multiwavelength detector, meaningful data in 3-D space can be collected with much faster speed of data generation. N2 - In der vorliegenden Arbeit wurde die Entwicklung neuer Detektoren für die Analytische Ultrazentrifugation (AUZ) untersucht und vorangetrieben. Im Gegensatz zu chromatgraphischen. Fraktionierungsmethoden werden Multidetektionssysteme bis heute nicht in der AUZ eingesetzt. Hier wird die Möglichkeit geprüft, bekannte spektroskopische sowie Streumethoden simultan zur Probenanalyse in der AUZ einzusetzen mit dem Ziel, simultan komplimentäre Informationen über die Probe zu erhalten. So wurde versucht, Raman- und UV/VIS-Spektroskopie (letztere mit der Möglichkeit, das gesamte Wellenlängenspektrum auszunutzen) und statische Lichtstreuung zu kombinieren, um das Analytverhalten während des Ultrazentrifugationsexperimentes zu untersuchen. Es wurden zum einen die Ramanspektroskopie als Detektionssystem für chemische Funktionalität in der AUZ geprüft und zum anderen gezeigt, daß die statische Kleinwinkel Lichtstreuung als direkter Molmassendetektor für den Einsatz in der AUZ geeignet erscheint. Zum anderen wurde die Entwicklung eines Multi-Wellenlängen-UV/VIS-Detektors abgeschlossen, um seine Eignung für den Einsatz in der AUZ und die damit verbundene Möglichkeiten der schnelleren und umfassenderen Datenerzeugung gegenüber kommerziellen Geräten zu zeigen. Dieser Multiwellendetektor liefert anstelle eines Absorptionswertes für jede radiale Position in der Messzelle direkt ein ganzes UV-Vis Spektrum und erzeugt eine zusaetzliche Dimension der Messdaten, was die Möglichkeiten der Analyse von komplexen Systemen mit multiplen Chromophoren, Teilchengrößenbestimmung über Wellenlängenabhängigkeit der Trübung oder auch der Datenmittelung enorm vergrößert. Desweiteren erlaubt der Detektor die Anwendung von Geschwindigkeitsprofilen zur Analyse extrem polydisperser Systeme. Die Entwicklung des Detektors beruht auf einem auf Linsen basierenden System mit modularem Aufbau. Dabei war die sorgfältige Ausrichtung des optischen Systems ein essentieller Punkt, um seine Eignung zu überprüfen zu können. An einer Mischung von drei Kolloiden, Halbleiternanopartikeln sowie Proteinen und deren Mischungen ist es hier gelungen, die erfolgreiche Entwicklung des UV/VIS-Detektors zu demonstrieren: Die Daten konnten schneller und mit wesentlich mehr Informationsgehalt, als auf allen kommerziellen Geräten generiert werden. Die Sedimentationskoeffizientenverteilungen stimmen dabei mit denen aus herkömmlichen Sedimentationsgeschwindigkeitsexperimenten überein, unterliegen jedoch nicht einer signifikanten diffusionsbedingten Verbreiterung. Es ist in dieser Arbeit somit gelungen, zum einen die Lichtstreuung als aussichtsreiche Methode für ein Detektorsystem in der AUZ aufzuzeigen, und zum anderen einen Multi-Wellenlängen-UV/VIS-Detektor zu entwickeln, der eine Datenerzeugung von bislang noch nicht erreichter Schnelligkeit im dreidimensionalen Raum ermöglicht. KW - Ultrazentrifuge KW - Detektor KW - Detektor-Entwicklung KW - SLS KW - UV/VIS KW - Raman KW - detector development KW - SLS KW - UV/VIS KW - Raman Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-8215 ER - TY - THES A1 - Bivigou Koumba, Achille Mayelle T1 - Design, Synthesis and Characterisation of Amphiphilic Symmetrical triblock copolymers by the RAFT process : their self-organisation in dilute and concentrated aqueous solutions T1 - Design, Synthese und Charakterisierung von amphiphilen symmetrischen Triblock-Copolymeren anhand des RAFT Prozesses : ihre Selbstorganisation in wässrigen verdünnten und höher konzentrierten Lösungen N2 - This work presents the synthesis and the self-assembly of symmetrical amphiphilic ABA and BAB triblock copolymers in dilute, semi-concentrated and highly concentrated aqueous solution. A series of new bifunctional bistrithiocarbonates as RAFT agents was used to synthesise these triblock copolymers, which are characterised by a long hydrophilic middle block and relatively small, but strongly hydrophobic end blocks. As hydrophilic A blocks, poly(N-isopropylacrylamide) (PNIPAM) and poly(methoxy diethylene glycol acrylate) (PMDEGA) were employed, while as hydrophobic B blocks, poly(4-tert-butyl styrene), polystyrene, poly(3,5-dibromo benzyl acrylate), poly(2-ethylhexyl acrylate), and poly(octadecyl acrylate) were explored as building blocks with different hydrophobicities and glass transition temperatures. The five bifunctional trithiocarbonates synthesised belong to two classes: the first are RAFT agents, which position the active group of the growing polymer chain at the outer ends of the polymer (Z-C(=S)-S-R-S-C(=S)-Z, type I). The second class places the active groups in the middle of the growing polymer chain (R-S-C(=S)-Z-C(=S)-S-R, type II). These RAFT agents enable the straightforward synthesis of amphiphilic triblock copolymers in only two steps, allowing to vary the nature of the hydrophobic blocks as well as the length of the hydrophobic and hydrophilic blocks broadly with good molar mass control and narrow polydispersities. Specific side reactions were observed among some RAFT agents including the elimination of ethylenetrithiocarbonate in the early stage of the polymerisation of styrene mediated by certain agents of the type II, while the use of the RAFT agents of type I resulted in retardation of the chain extension of PNIPAM with styrene. These results underline the need of a careful choice of RAFT agents for a given task. The various copolymers self-assemble in dilute and semi-concentrated aqueous solution into small flower-like micelles. No indication for the formation of micellar clusters was found, while only at high concentration, physical hydrogels are formed. The reversible thermoresponsive behaviour of the ABA and BAB type copolymer solutions in water with A made of PNIPAM was examined by turbidimetry and dynamic light scattering (DLS). The cloud point of the copolymers was nearly identical to the cloud point of the homopolymer and varied between 28-32 °C with concentrations from 0.01 to 50 wt%. This is attributed to the formation of micelles where the hydrophobic blocks are shielded from a direct contact with water, so that the hydrophobic interactions of the copolymers are nearly the same as for pure PNIPAM. Dynamic light scattering measurements showed the presence of small micelles at ambient temperature. The aggregate size dramatically increased above the cloud point, indicating a change of aggregate morphology into clusters due to the thermosensitivity of the PNIPAM block. The rheological behaviour of the amphiphilic BAB triblock copolymers demonstrated the formation of hydrogels at high concentrations, typically above 30-35 wt%. The minimum concentration to induce hydrogels decreased with the increasing glass transition temperatures and increasing length of the end blocks. The weak tendency to form hydrogels was attributed to a small share of bridged micelles only, due to the strong segregation regime occurring. In order to learn about the role of the nature of the thermoresponsive block for the aggregation, a new BAB triblock copolymer consisting of short polystyrene end blocks and PMDEGA as stimuli-responsive middle block was prepared and investigated. Contrary to PNIPAM, dilute aqueous solutions of PMDEGA and of its block copolymers showed reversible phase transition temperatures characterised by a strong dependence on the polymer composition. Moreover, the PMDEGA block copolymer allowed the formation of physical hydrogels at lower concentration, i.e. from 20 wt%. This result suggests that PMDEGA has a higher degree of water-swellability than PNIPAM. N2 - Die Arbeit behandelt die Synthese und das Selbstorganisationsverhalten von neuen funktionellen symmetrischen "stimuli-responsiven" Triblockcopolymeren ABA und BAB in wässrigen verdünnten und höher konzentrierten Lösungen. Neue symmetrische, bifunktionelle Bistrithiocarbonate wurden als RAFT-Agentien benutzt, um Triblockcopolymere mit langen hydrophilen (A) Innen- und kurzen hydrophoben (B) Außenblöcken zu synthetisieren. Als hydrophile A Blöcke wurden Poly(N-isopropylacrylamid) PNIPAM und Poly(methoxy diethylene glykol acrylat) PMDEGA benutzt, während als hydrophobe Blöcke B Poly(4-tert-butyl styrol), Polystyrol, Poly(3,5-dibromo benzyl acrylat), Poly(2-ethylhexyl acrylat), und Poly(octadecyl acrylat) als Bausteine mit unterschiedlicher Glasübergangstemperatur untersucht wurden. Die Selbstorganisation von ABA und BAB Copolymeren in Wasser mit A Blöcken aus PNIPAM wurde anhand von Trübungsphotometrie, dynamischer Lichtstreuung (DLS) und Rheologie untersucht. Die amphiphilen Blockcopolymere sind direkt wasserlöslich. Bei Konzentrationen von 0.01 bis 50 wt% zeigen Trübungsmessungen bei den Blockcopolymeren wie bei den Homopolymeren eine Übergangstemperatur bei 28-32 °C. Zurückzuführen ist dies auf die Bildung von Mizellen, bei der die hydrophoben Blöcke von einem direkten Kontakt mit Wasser abgeschirmt werden. DLS zeigt kleine Mizellen bei niedrigen Temperaturen und Aggregate mit großem hydrodynamischem Durchmesser bei Temperaturen oberhalb der Übergangstemperatur. Die rheologische Untersuchung von BAB Polymeren zeigt die Bildung von Hydrogelen bei höheren Konzentrationen (über 30-35 wt%). Die minimal benötigte Konzentration, bei der die von Hydrogelen auftreten, nimmt mit wachsender Glasübergangstemperatur ab, und nimmt mit der Länge der hydrophoben Blöcke B zu. Im Unterschied zu PNIPAM zeigen wässrige Lösungen von PMDEGA und seinen Blockcopolymeren reversible Übergangstemperaturen abhängig von der chemischen Struktur. Außerdem bilden PMDEGA Blockcopolymere Hydrogele bei niedriger Konzentration (ab 20 wt%). Dieses Ergebnis deutet darauf hin, dass PMDEGA stärker Wasser bindet als PNIPAM. KW - Design KW - Synthese KW - Charakterisierung KW - Triblock-Copolymere KW - RAFT KW - Design KW - Synthesis KW - Characterisation KW - Triblock Copolymers KW - RAFT Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-39549 ER - TY - THES A1 - Bojdys, Michael Janus T1 - On new allotropes and nanostructures of carbon nitrides T1 - Über neue Allotrope und Nanostrukturen von Karbonitriden N2 - In the first section of the thesis graphitic carbon nitride was for the first time synthesised using the high-temperature condensation of dicyandiamide (DCDA) – a simple molecular precursor – in a eutectic salt melt of lithium chloride and potassium chloride. The extent of condensation, namely next to complete conversion of all reactive end groups, was verified by elemental microanalysis and vibrational spectroscopy. TEM- and SEM-measurements gave detailed insight into the well-defined morphology of these organic crystals, which are not based on 0D or 1D constituents like known molecular or short-chain polymeric crystals but on the packing motif of extended 2D frameworks. The proposed crystal structure of this g-C3N4 species was derived in analogy to graphite by means of extensive powder XRD studies, indexing and refinement. It is based on sheets of hexagonally arranged s-heptazine (C6N7) units that are held together by covalent bonds between C and N atoms. These sheets stack in a graphitic, staggered fashion adopting an AB-motif, as corroborated by powder X-ray diffractometry and high-resolution transmission electron microscopy. This study was contrasted with one of many popular – yet unsuccessful – approaches in the last 30 years of scientific literature to perform the condensation of an extended carbon nitride species through synthesis in the bulk. The second section expands the repertoire of available salt melts introducing the lithium bromide and potassium bromide eutectic as an excellent medium to obtain a new phase of graphitic carbon nitride. The combination of SEM, TEM, PXRD and electron diffraction reveals that the new graphitic carbon nitride phase stacks in an ABA’ motif forming unprecedentedly large crystals. This section seizes the notion of the preceding chapter, that condensation in a eutectic salt melt is the key to obtain a high degree of conversion mainly through a solvatory effect. At the close of this chapter ionothermal synthesis is seen established as a powerful tool to overcome the inherent kinetic problems of solid state reactions such as incomplete polymerisation and condensation in the bulk especially when the temperature requirement of the reaction in question falls into the proverbial “no man’s land” of classical solvents, i.e. above 250 to 300 °C. The following section puts the claim to the test, that the crystalline carbon nitrides obtained from a salt melt are indeed graphitic. A typical property of graphite – namely the accessibility of its interplanar space for guest molecules – is transferred to the graphitic carbon nitride system. Metallic potassium and graphitic carbon nitride are converted to give the potassium intercalation compound, K(C6N8)3 designated according to its stoichiometry and proposed crystal structure. Reaction of the intercalate with aqueous solvents triggers the exfoliation of the graphitic carbon nitride material and – for the first time – enables the access of singular (or multiple) carbon nitride sheets analogous to graphene as seen in the formation of sheets, bundles and scrolls of carbon nitride in TEM imaging. The thus exfoliated sheets form a stable, strongly fluorescent solution in aqueous media, which shows no sign in UV/Vis spectroscopy that the aromaticity of individual sheets was subject to degradation. The final section expands on the mechanism underlying the formation of graphitic carbon nitride by literally expanding the distance between the covalently linked heptazine units which constitute these materials. A close examination of all proposed reaction mechanisms to-date in the light of exhaustive DSC/MS experiments highlights the possibility that the heptazine unit can be formed from smaller molecules, even if some of the designated leaving groups (such as ammonia) are substituted by an element, R, which later on remains linked to the nascent heptazine. Furthermore, it is suggested that the key functional groups in the process are the triazine- (Tz) and the carbonitrile- (CN) group. On the basis of these assumptions, molecular precursors are tailored which encompass all necessary functional groups to form a central heptazine unit of threefold, planar symmetry and then still retain outward functionalities for self-propagated condensation in all three directions. Two model systems based on a para-aryl (ArCNTz) and para-biphenyl (BiPhCNTz) precursors are devised via a facile synthetic procedure and then condensed in an ionothermal process to yield the heptazine based frameworks, HBF-1 and HBF-2. Due to the structural motifs of their molecular precursors, individual sheets of HBF-1 and HBF-2 span cavities of 14.2 Å and 23.0 Å respectively which makes both materials attractive as potential organic zeolites. Crystallographic analysis confirms the formation of ABA’ layered, graphitic systems, and the extent of condensation is confirmed as next-to-perfect by elemental analysis and vibrational spectroscopy. N2 - Die vorliegende Arbeit befasst sich mit der Synthese und Charakterisierung neuer Allotropen und Nanostrukturen von Karbonitriden und berührt einige ihrer möglichen Anwendungen. Alle gezeigten, ausgedehnten, kovalent verbundenen Karbonitridgerüste wurden in einem ionothermalen Syntheseprozess – einer Hochtemperaturbehandlung in einem eutektischen Salzgemisch als ungewöhnlichem Lösungsmittel – aus einfachen Präkursormolkülen erzeugt. Der Kondensationsmechanismus folgt einer temperaturinduzierten Deaminierung und Bildung einer ausgedehnten, aromatischen Einheit; des dreifach substituierten Heptazines. Die Dissertation folgt vier übergreifenden Themen, beginnend mit der Einleitung in Karbonitridsysteme und der Suche nach einem Material, welches einzig aus Kohlenstoff und Stickstoff aufgebaut ist – einer Suche, die 1834 mit den Beobachtungen Justus von Liebigs „über einige Stickstoffverbindungen“ begann. Der erste Abschnitt zeigt die erfolgreiche Synthese von graphitischem Karbonitrid (g-C3N4); einer Spezies, welche auf Schichten hexagonal angeordneter s-Heptazineinheiten beruht, die durch kovalente Bindungen zwischen C- und N-Atomen zusammengehalten werden, und welche in einer graphitischen, verschobenen Art und Weise gestapelt sind. Der zweite Abschnitt berührt die Vielfalt von Salzschmelzensystemen, die für die Ionothermalsynthese geeignet sind und zeigt auf, dass die bloße Veränderung der Salzschmelze eine andere Kristallphase des graphitischen Karbonitrides ergibt – das g-C3N4-mod2. Im dritten Abschnitt wird vom Graphit bekannte Interkallationschemie auf das g-C3N4 angewendet, um eine Kalliuminterkallationsverbindung des graphitischen Karbonitirdes zu erhalten (K(C6N8)3). Diese Verbindung kann in Analogie zum graphitischen System leicht exfoliiert werden, um Bündel von Karbonitridnanoschichten zu erhalten, und weist darüberhinaus interessante optische Eigenschaften auf. Der vierte und letzte Abschnitt handelt von der Einführung von Aryl- und Biphenylbrücken in das Karbonitridmaterial durch rationale Synthese der Präkursormoleküle. Diese ergeben die heptazinbasierten Frameworks, HBF-1 und HBF-2 – zwei kovalente, organische Gerüste. KW - kovalente Rahmenbedingungen KW - mehrschichtige Verbindungen KW - Triazin KW - Heptazine KW - Karbonnitrid Ionothermalsynthese KW - Salzschmelze KW - covalent frameworks KW - layered compounds KW - triazine KW - heptazine KW - carbon nitride KW - ionothermal synthesis KW - salt melt Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-41236 ER - TY - THES A1 - Borisova, Dimitriya T1 - Feedback active coatings based on mesoporous silica containers T1 - Rückkopplungsaktive Beschichtungen basierend auf mesoporösen Silika-Behältern N2 - Metalle werden oft während ihrer Anwendung korrosiven Bedingungen ausgesetzt, was ihre Alterungsbeständigkeit reduziert. Deswegen werden korrosionsanfällige Metalle, wie Aluminiumlegierungen mit Schutzbeschichtungen versehen, um den Korrosionsprozess aktiv oder passiv zu verhindern. Die klassischen Schutzbeschichtungen funktionieren als physikalische Barriere zwischen Metall und korrosiver Umgebung und bieten einen passiven Korrosionsschutz nur, wenn sie unbeschädigt sind. Im Gegensatz dazu kann die Korrosion auch im Fall einer Beschädigung mittels aktiver Schutzbeschichtungen gehemmt werden. Chromathaltige Beschichtungen bieten heutzutage den besten aktiven Korrosionsschutz für Aluminiumlegierungen. Aufgrund ihrer Giftigkeit wurden diese weltweit verboten und müssen durch neue umweltfreundliche Schutzbeschichtungen ersetzt werden. Ein potentieller Ersatz sind Schutzbeschichtungen mit integrierten Nano- und Mikrobehältern, die mit ungiftigem Inhibitor gefüllt sind. In dieser Arbeit werden die Entwicklung und Optimierung solcher aktiver Schutzbeschichtungen für die industriell wichtige Aluminiumlegierung AA2024-T3 dargestellt Mesoporöse Silika-Behälter wurden mit dem ungiftigen Inhibitor (2-Mercaptobenzothiazol) beladen und dann in die Matrix anorganischer (SiOx/ZrOx) oder organischer (wasserbasiert) Schichten dispergiert. Zwei Sorten von Silika-Behältern mit unterschiedlichen Größen (d ≈ 80 and 700 nm) wurden verwendet. Diese haben eine große spezifische Oberfläche (≈ 1000 m² g-1), eine enge Porengrößenverteilung mit mittlerer Porenweite ≈ 3 nm und ein großes Porenvolumen (≈ 1 mL g-1). Dank dieser Eigenschaften können große Inhibitormengen im Behälterinneren adsorbiert und gehalten werden. Die Inhibitormoleküle werden bei korrosionsbedingter Erhöhung des pH-Wertes gelöst und freigegeben. Die Konzentration, Position und Größe der integrierten Behälter wurden variiert um die besten Bedingungen für einen optimalen Korrosionsschutz zu bestimmen. Es wurde festgestellt, dass eine gute Korrosionsschutzleistung durch einen Kompromiss zwischen ausreichender Inhibitormenge und guten Barriereeigenschaften hervorgerufen wird. Diese Studie erweitert das Wissen über die wichtigsten Faktoren, die den Korrosionsschutz beeinflussen. Somit wurde die Entwicklung effizienter, aktiver Schutzbeschichtungen ermöglicht, die auf mit Inhibitor beladenen Behältern basieren. N2 - Metals are often used in environments that are conducive to corrosion, which leads to a reduction in their mechanical properties and durability. Coatings are applied to corrosion-prone metals such as aluminum alloys to inhibit the destructive surface process of corrosion in a passive or active way. Standard anticorrosive coatings function as a physical barrier between the material and the corrosive environment and provide passive protection only when intact. In contrast, active protection prevents or slows down corrosion even when the main barrier is damaged. The most effective industrially used active corrosion inhibition for aluminum alloys is provided by chromate conversion coatings. However, their toxicity and worldwide restriction provoke an urgent need for finding environmentally friendly corrosion preventing systems. A promising approach to replace the toxic chromate coatings is to embed particles containing nontoxic inhibitor in a passive coating matrix. This work presents the development and optimization of effective anticorrosive coatings for the industrially important aluminum alloy, AA2024-T3 using this approach. The protective coatings were prepared by dispersing mesoporous silica containers, loaded with the nontoxic corrosion inhibitor 2-mercaptobenzothiazole, in a passive sol-gel (SiOx/ZrOx) or organic water-based layer. Two types of porous silica containers with different sizes (d ≈ 80 and 700 nm, respectively) were investigated. The studied robust containers exhibit high surface area (≈ 1000 m² g-1), narrow pore size distribution (dpore ≈ 3 nm) and large pore volume (≈ 1 mL g-1) as determined by N2 sorption measurements. These properties favored the subsequent adsorption and storage of a relatively large amount of inhibitor as well as its release in response to pH changes induced by the corrosion process. The concentration, position and size of the embedded containers were varied to ascertain the optimum conditions for overall anticorrosion performance. Attaining high anticorrosion efficiency was found to require a compromise between delivering an optimal amount of corrosion inhibitor and preserving the coating barrier properties. This study broadens the knowledge about the main factors influencing the coating anticorrosion efficiency and assists the development of optimum active anticorrosive coatings doped with inhibitor loaded containers. KW - Korrosion KW - Beschichtungen KW - Aluminiumlegierung KW - Silika KW - Nanopartikel KW - mesoporös KW - corrosion KW - coating KW - aluminum alloy KW - silica nanoparticles KW - mesoporous Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-63505 ER - TY - THES A1 - Brandi, Francesco T1 - Integrated biorefinery in continuous flow systems using sustainable heterogeneous catalysts T1 - Integrierte Bioraffinerie in kontinuierlichen Fließsystemen unter Verwendung nachhaltiger heterogener Katalysatoren N2 - The negative impact of crude oil on the environment has led to a necessary transition toward alternative, renewable, and sustainable resources. In this regard, lignocellulosic biomass (LCB) is a promising renewable and sustainable alternative to crude oil for the production of fine chemicals and fuels in a so-called biorefinery process. LCB is composed of polysaccharides (cellulose and hemicellulose), as well as aromatics (lignin). The development of a sustainable and economically advantageous biorefinery depends on the complete and efficient valorization of all components. Therefore, in the new generation of biorefinery, the so-called biorefinery of type III, the LCB feedstocks are selectively deconstructed and catalytically transformed into platform chemicals. For this purpose, the development of highly stable and efficient catalysts is crucial for progress toward viability in biorefinery. Furthermore, a modern and integrated biorefinery relies on process and reactor design, toward more efficient and cost-effective methodologies that minimize waste. In this context, the usage of continuous flow systems has the potential to provide safe, sustainable, and innovative transformations with simple process integration and scalability for biorefinery schemes. This thesis addresses three main challenges for future biorefinery: catalyst synthesis, waste feedstock valorization, and usage of continuous flow technology. Firstly, a cheap, scalable, and sustainable approach is presented for the synthesis of an efficient and stable 35 wt.-% Ni catalyst on highly porous nitrogen-doped carbon support (35Ni/NDC) in pellet shape. Initially, the performance of this catalyst was evaluated for the aqueous phase hydrogenation of LCB-derived compounds such as glucose, xylose, and vanillin in continuous flow systems. The 35Ni/NDC catalyst exhibited high catalytic performances in three tested hydrogenation reactions, i.e., sorbitol, xylitol, and 2-methoxy-4-methylphenol with yields of 82 mol%, 62 mol%, and 100 mol% respectively. In addition, the 35Ni/NDC catalyst exhibited remarkable stability over a long time on stream in continuous flow (40 h). Furthermore, the 35Ni/NDC catalyst was combined with commercially available Beta zeolite in a dual–column integrated process for isosorbide production from glucose (yield 83 mol%). Finally, 35Ni/NDC was applied for the valorization of industrial waste products, namely sodium lignosulfonate (LS) and beech wood sawdust (BWS) in continuous flow systems. The LS depolymerization was conducted combining solvothermal fragmentation of water/alcohol mixtures (i.e.,methanol/water and ethanol/water) with catalytic hydrogenolysis/hydrogenation (SHF). The depolymerization was found to occur thermally in absence of catalyst with a tunable molecular weight according to temperature. Furthermore, the SHF generated an optimized cumulative yield of lignin-derived phenolic monomers of 42 mg gLS-1. Similarly, a solvothermal and reductive catalytic fragmentation (SF-RCF) of BWS was conducted using MeOH and MeTHF as a solvent. In this case, the optimized total lignin-derived phenolic monomers yield was found of 247 mg gKL-1. N2 - Die negativen Auswirkungen von Rohöl auf die Umwelt haben zu einem notwendigen Übergang zu alternativen, erneuerbaren und nachhaltigen Ressourcen geführt. In dieser Hinsicht ist lignozellulosehaltige Biomasse (LCB) eine vielversprechende erneuerbare und nachhaltige Alternative zu Erdöl für die Herstellung von Feinchemikalien und Kraftstoffen in einem sogenannten Bioraffinerie-Prozess. LCB setzt sich aus Polysacchariden (Cellulose und Hemicellulose) sowie Aromaten (Lignin) zusammen. Die Entwicklung einer nachhaltigen und wirtschaftlich vorteilhaften Bioraffinerie hängt von der vollständigen und effizienten Verwertung aller Komponenten ab. Zu diesem Zweck ist die Entwicklung hochstabiler und effizienter Katalysatoren entscheidend für den Fortschritt in Richtung Bioraffinerie-Wirtschaftlichkeit. Darüber hinaus ist eine moderne und integrierte Bioraffinerie auf ein Prozess- und Reaktordesign angewiesen, das auf effizientere und kostengünstigere Methoden abzielt, die den Abfall minimieren. In diesem Zusammenhang hat die Verwendung von kontinuierlichen Durchflusssystemen das Potenzial, sichere, nachhaltige und innovative Transformationen mit einfacher Prozessintegration und Skalierbarkeit für Bioraffineriesysteme zu bieten. Diese Arbeit befasst sich mit drei wesentlichen Herausforderungen für die zukünftige Bioraffinerie: Katalysatorsynthese, Valorisierung von Abfallstoffen und Einsatz von kontinuierlicher Durchflusstechnik. Zuerst wird ein kostengünstiger, skalierbarer und nachhaltiger Ansatz für die Synthese eines effizienten und stabilen 35-Gew.-%-Ni-Katalysators auf einem hochporösen, stickstoffdotierten Kohlenstoffträger (35Ni/NDC) in Pelletform vorgestellt. Zunächst wurde die Leistung dieses Katalysators für die Hydrierung von LCB-abgeleiteten Verbindungen wie Glucose, Xylose und Vanillin in kontinuierlichen Durchflusssystemen in wässriger Phase bewertet. Der 35Ni/NDC-Katalysator zeigte hohe katalytische Leistungen in drei getesteten Hydrierungsreaktionen, d. h. Sorbit, Xylit und 2-Methoxy-4-methylphenol mit Ausbeuten von 82 mol%, 62 mol% bzw. 100 mol%. Darüber hinaus zeigte der 35Ni/NDC-Katalysator eine bemerkenswerte Stabilität über eine lange Zeit im kontinuierlichen Fluss (40 h). Auβerrdem wurde der 35Ni/NDC-Katalysator mit handelsüblichem Beta-Zeolith in einem integrierten Zweisäulenprozess für die Isosorbid-Produktion aus Glukose kombiniert (Ausbeute 83 mol%). Schließlich wurde 35Ni/NDC für die Valorisierung von industriellen Abfallprodukten, nämlich Natriumlignosulfonat (LS) und Buchenholzsägemehl (BWS) in kontinuierlichen Durchflusssystemen eingesetzt. Die Depolymerisation von LS wurde durch eine Kombination von solvothermischer Fragmentierung von Wasser/Alkohol-Gemischen (d.h. MeOH/Wasser und Ethanol/Wasser) mit katalytischer Hydrogenolyse/Hydrierung (SHF) durchgeführt. Es wurde festgestellt, dass die Depolymerisation thermisch in Abwesenheit des Katalysators mit einem abstimmbaren Molekulargewicht in Abhängigkeit von der Temperatur erfolgt. Außerdem wurde mit der SHF eine optimierte kumulative Monomerausbeute von 42 mg gLS-1 erzielt. In ähnlicher Weise wurde eine solvothermale und reduktiv-katalytische Fragmentierung (SF-RCF) von BWS mit MeOH und MeTHF als Lösungsmittel durchgeführt. In diesem Fall wurde eine optimierte Gesamtmonomerausbeute von 247 mg gKL-1 gefunden. KW - sustainable chemistry KW - green chemistry KW - biorefinery KW - flow chemistry KW - heterogeneous catalysis KW - Bioraffinerie KW - grüne Chemie KW - heterogene Katalyse KW - Strömungschemie KW - nachhaltige Chemie Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-537660 ER - TY - THES A1 - Braun, Max T1 - Heterogeneous Catalysis for the Conversion of Fructose to Chemicals and Fuel in a Continuous Flow Process T1 - Umsetzung von Fruktose zu Chemikalien und Treibstoff mittels heterogener Katalysatoren in einem kontinuierlichen Prozess N2 - Die Umsetzung von Zucker (Kohlenhydrate) in einem kontinuierlichen Prozess eröffnet Möglichkeiten der Synthese diverser Chemikalien und Treibstoff aus erneuerbaren Ressourcen, welche heute überwiegend aus fossilen Quellen stammen. Passend zum Konzept der Bioraffinerie und der „grünen Chemie“, liegt der Fokus dieser Arbeit auf der Umsetzung von in Ethanol gelöster Fruktose in einem kontinuierlichen Verfahren, mit Hilfe eigens entwickelter heterogener Katalysatoren. Die Dehydratisierung von Fruktose wird mit einem heterogenen Säurekatalysator realisiert, während die Folgeprodukte mittels einer Hydrodesoxygenierung umgesetzt werden. Für den zweiten Schritt kommen Metallkatalysatoren auf Basis von Nickel und Wolframcarbid (WC) zum Einsatz, wodurch der Einsatz teurer Edelmetalle vermieden werden kann. Hauptprodukte des zweistufigen Verfahrens sind 2,5-Dimethylfuran (DMF) und Ethyllevulinat (EL). Beide Moleküle sind vielversprechende alternative Treibstoffe, bzw. können gebräuchlichen Treibstoffen beigemischt werden, um deren Einsatz zu reduzieren und schrittweise zu substituieren. Alternativ können die Zwischenprodukte der Dehydratisierung, sowie DMF und EL weiter zu Chemikalien umgesetzt werden, welche in der Polymersynthese, als Lösungsmittel oder als Grundchemikalien eingesetzt werden können. Die Entwicklung der jeweiligen Katalysatoren für Dehydratisierungs- und Hydrodesoxygenierungsreaktionen erfolgt auf Basis von karbonisierter Biomasse, sowie Wolframcarbid. Die jeweiligen Reaktivitäten werden durch Standardreaktionen getestet, wobei sich Wolframcarbid in Nanopartikelform, in Kombination mit Wasserstoff als sehr aktiv erwiesen hat. Der selbst entwickelte aktivierte Kohlenstoff, das kommerzielle Amberlyst 15, sowie Wolframcarbid mit zusätzlichen Nickel-Nanopartikeln werden für weiterführende Reaktionen in einem kontinuierlichen Prozess herangezogen und kombiniert. Um den Umsatz von Fruktose zu DMF in einer „zwei Reaktoren Anlage“ zu ermöglichen, wird eine Erweiterung eines kommerziellen Reaktorsystems um einen weiteren Reaktor vorgenommen. Die Verweilzeit in der Reaktoranlage beträgt somit ca. 14 Minuten, wobei 11 Minuten auf die erste Säule (Dehydratisierung) und 3 Minuten auf die zweite Säule (Hydrodesoxygenierung) entfallen. In diesem kontinuierlichen und zweistufigen System lassen sich Ausbeuten von 38.5 % DMF und 47 % EL erzielen. Ein kontinuierlicher Lauf von sieben Stunden zeigt die Stabilität der eingesetzten Katalysatoren, auch wenn eine geringe Deaktivierung des Dehydratisierungskatalysators beobachtet werden kann. Der Ni@WC Katalysator zeigte hingegen keine Abnahme der Nickel Konzentration und somit kommt es zu keiner Auswaschung des Metalls. Das gebildete EL wurde hingegen nicht umgesetzt und verbleibt unverändert in Lösung. Das zweistufige System wurde schließlich in einem Mischkatalysatorsystem kombiniert, wobei auf aktivierten und sulfonierten Kohlenstoff zurückgegriffen wurde. Dieser zeigte bereits eine Transferhydrodesoxygenierungsaktivität. Diese Beobachtung ist deshalb bemerkenswert, da erst seit kurzem bekannt ist, dass Graphenstrukturen an sich katalytisch aktiv sein können. Um diese Aktivität weiter zu steigern, wurde der aktivierte Kohlenstoff mit 10 wt% Ni@WC gemischt, sodass beide Katalysatoren in einer Säule vorliegen. Die ursprünglichen 2 % DMF Ausbeute mit reinem aktivierten Kohlenstoff können somit auf 12 % gesteigert werden, da das Folgeprodukt EL hierbei vermieden wird und das Zwischenprodukt „HMF Derivat“ direkt zu DMF weiter reagieren kann. Dieses Ergebnis zeigt das Potential der „ein Reaktor Umsetzung“, weshalb eine kontinuierliche Durchflussreaktoranlage im Litermaßstab als Scale-Up des vorhergehenden Labormaßstabs realisiert wurde. Der 800 mm x 28.5 mm Reaktor bedient eine maximale Flussrate von 50 mL min-1, Drücke von 100 bar und Temperaturen bis zu 500 °C. N2 - The valorization of carbohydrates is one of the most promising fields in green chemistry, as it enables to produce bulk chemicals and fuels out of renewable and abundant resources, instead of further exploiting fossil feedstocks. The focus in this thesis is the conversion of fructose, using dehydration and hydrodeoxygenation reactions. The main goal is to find an easy continuous process, including the solubility of the sugar in a green solvent, the conversion over a solid acid as well as over a metal@tungsten carbide catalyst. At the beginning of this thesis, solid acid catalysts are synthesized by using carbohydrate material like glucose and starch at high temperatures (up to 600 °C). Additionally a third carbon is synthesized, using an activation method based on Ca(OH)2. After carbonization and further sulfonation, using fuming sulfuric acid, the three resulting catalysts are characterized together with sulfonated carbon black and Amberlyst 15 as references. In order to test all solid acid catalysts in reaction, a 250 mm x 4.6 mm stainless steel column is used as a fixed-bed continuous reactor. The temperature (110 °C to 250 °C) and residence time (2 to 30 minutes) is varied, and a direct relationship between contact time and selectivity is determined. The reaction mechanism, as well as the product distribution is showing a dehydration step of fructose towards 5-hydroxymethylfurfural (HMF). These furan-ring molecules are considered as “sleeping giants”, due to the possibility of using them as fuel, but also for upgrading them to chemicals like terephthalic acid or p-xylene. Consecutive reactions are producing levulinic acid, as well as condensation products with ethanol and formic acid. The activated carbon is additionally showing a 2 % yield of 2,5-Dimethylfuran (DMF) production, pointing towards the extraordinary properties of this catalyst. Without a metal catalyst present, what is normally necessary for hydrogenation reactions, a transferhydrogenation (with formic acid) is observed. The active catalyst was therefore carbon itself, what activated the hydrogen on its surface. This phenomenon was just very rarely observed so far. Expensive noble metals are the material of choice, when it comes to hydrogenation reactions nowadays and cheaper alternatives are necessary. By postulating a similar electronic structure of tungsten carbide (WC) to platinum by Lewy and Boudart, research is focusing on the replacement of Pt. The production of nano-sized tungsten carbide particles (7.5 ± 2.5 nm, 70 m2 g-1) is enabled by the so called “urea glass route” and its catalytic performances are compared to commercial material. It is shown, that the activity is strongly dependent on the size of the particles as well as the surface area. Nano-sized tungsten carbide is showing activity for hydrogenation reactions under mild conditions (maximum 150 °C, 30 bar). This material therefore opens up new possibilities for replacing the rare and expensive platinum with tungsten carbide based catalysts. Additionally different metal nanoparticles of palladium, copper and nickel are deposited on top of WC to further promote its reactivity. The nickel nanoparticles are strongly connected to WC and showed the best activity as well as selectivity for upgrading HMF with hydrodeoxygenation. The Ni@WC is not leaching and is showing very good hydrodeoxygenation properties with DMF yields up to 90 percent. Copper@WC is not showing good activity and palladium@WC enables undesired consecutive reactions, hydrogenating the furan ring system. In order to enable the upgrade of fructose to DMF directly in a continuous system, the current H CUBE Pro TM hydrogenation system is customized with a second reaction column. A 250 mm x 4.6 mm stainless steel reactor column is connected ahead of the hydrogen insertion, enabling the dehydration of fructose to HMF derivatives, before pumping these products into the second column for hydrogenation. The overall residence time in the two column reactor system is 14 minutes. The overall results are an almost full conversion with a yield of 38.5 % DMF and 47 % yield of EL. The main disadvantage is the formation of higher mass products, so called humins, which start depositing on top of the catalysts, blocking their active sites. In general it can be stated, that a two column system goes along with a higher investment as well as more maintenance costs, compared to a one column catalytic approach. To develop a catalyst, which is on the one hand able to dehydrate as well as hydrodeoxygenate the reactants, is aimed for at the last part of the thesis. The activated carbon however shows already activity for hydrodeoxygenation without any metal present and offers itself therefore as an alternative to overcome the temperature instability of Amberlyst 15 (max. 120 °C) for a combined DMF production directly from fructose. The activity for the upgrade to DMF is increased from 2 % to 12 % DMF yield in one mixed continuous column. In order to scale up the entire one column approach, an 800 mm x 28.5 mm inner diameter column was planned and manufactured. The system is scaled up and assembled, whereas this flow reactor system is able to be run with 50 mL min-1 maximum flow rate, to stand a pressure of maximum 100 bar and be heated to around 500 °C. The tubing and connections, as well as the used devices are planned according to be safe and easy in use. The scaled-up approach offers a reaction column 120 times bigger (510 ml) then the first extension of the commercial system. This further extension offers the possibility of ranging between 1 and 1000 mL min-1, making it possible to use the approach in pilot plant applications. KW - Biorefinery KW - Catalysis KW - Hydroxymethylfurfural KW - Upgrade of Fructose KW - Bioraffinerie KW - Katalyse KW - Hydroxymethylfurfural KW - Aufarbeitung von Fruktose Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-410370 ER - TY - THES A1 - Buha, Jelena T1 - Nonaqueous syntheses of metal oxide and metal nitride nanoparticles T1 - Nichtwässrige Synthesen von Metalloxid- und Metallnitrid-Nanopartikeln N2 - Nanostructured materials are materials consisting of nanoparticulate building blocks on the scale of nanometers (i.e. 10-9 m). Composition, crystallinity and morphology can enhance or even induce new properties of the materials, which are desirable for todays and future technological applications. In this work, we have shown new strategies to synthesise metal oxide and metal nitride nanomaterials. The first part of the work deals with the study of nonaqueous synthesis of metal oxide nanoparticles. We succeeded in the synthesis of In2O3 nanopartcles where we could clearly influence the morphology by varying the type of the precursors and the solvents; of ZnO mesocrystals by using acetonitrile as a solvent; of transition metal oxides (Nb2O5, Ta2O5 and HfO2) that are particularly hard to obtain on the nanoscale and other technologically important materials. Solvothermal synthesis however is not restricted to formation of oxide materials only. In the second part we show examples of nonaqueous, solvothermal reactions of metal nitrides, but the main focus lies on the investigation of the influence of different morphologies of metal oxide precursors on the formation of the metal nitride nanoparticles. In spite of various reports, the number and variety of nanocrystalline metal nitrides is marginally small by comparison to metal oxides; hence preformed metal oxides as precursors for the preparation of metal nitrides are a logical choice. By reacting oxide nanoparticles with cyanamide, urea or melamine, at temperatures of 800 to 900 °C under nitrogen flow metal nitrides could be obtained. We studied in detail the influence of the starting material and realized that size, crystallinity, type of nitrogen source and temperature play the most important role. We have managed to propose and verify a dissolution-recrystallisation model as the formation mechanism. Furthermore we could show that the initial morphology of the oxides could be retained when ammonia flow was used instead. N2 - Nanostrukturierte Materialien sind Materialien, die aus nanopartikulären Baueinheiten in der Größenordnung von Nanonmetern (d.h. 10-9 m) bestehen. Zusammensetzung, Kristallinität und Morphologie können die natürlichen Eigenschaften dieser Materialien verbessern oder zusätzliche Eigenschaften erzeugen, die für heutige und zukünftige Anwendungen und Verfahren wünschenswert sind. In dieser Arbeit präsentieren wir neue Strategien zur Synthese von Nanopartikeln der Metaloxide und Metalnitride. Im einführenden Teil wird die nichtwässrige Synthese von Metaloxidnanopartikeln beschrieben. Uns gelang die Darstellung von In2O3 Nanopartikeln, deren Größe und Form wir durch die Wahl des Prekursors und des Lösemittels deutlich beeinflussen konnten; von ZnO Mesokristallen durch den Einsatz von Acetonitril als Lösemittel; von Übergangsmetalloxiden (Nb2O5, Ta2O5 and HfO2), die besonders schwer im Nanomaßstab zu erhalten sind und von anderen, technisch relevanten Materialien. Die Möglichkeiten der solvothermalen Synthese sind nicht mit der Darstellung von Oxidmaterialen erschöpft. Im zweiten Teil zeigen wir einige Beispiele nichtwässriger, solvothermaler Synthese von Metalnitriden auf; das Hauptaugenmerk liegt aber auf einer Betrachtung der Einflüsse der Morphologie von Metaloxidnanopartikelprekursoren auf die Bildung der Metalnitridnanopartikel. Die Anzahl und Vielfalt bekannter nanokristalliner Metalnitride ist verschwindend klein im Vergleich zu den Metaloxiden, die in der Fachliteratur etabliert sind und demzufolge einen reichen Baukasten an Prekursoren zur Darstellung von Metalnitriden liefern. Durch die Reaktion von Metaloxidnanopartikeln mit Cyanamid, Urea oder Melamine bei Temperaturen von 800 bis 900 °C unter Stickstofffluss konnten Metalnitride erhalten werden. Eine detaillierte Studie der Reaktionsbedingungen und des Reaktionsablaufs zeigte auf, dass Größe und Kristallinität der Metaloxide, die Art der Stickstoffquelle und die Temperatur die entscheidenden Faktoren sind und legte eine Auflösungs-Rekristallisation als Modelmechanismus dieser Art Reaktion nahe. Darüber hinaus konnte gezeigt worden, dass die anfängliche Morphologie des Oxids unter einem Ammoniafluss beibehalten werden konnte. KW - Nichtwässrige Synthese KW - Nanopartikel KW - Metalloxide KW - Metallnitride KW - nonaqueous synthesis KW - nanoparticles KW - metal oxides KW - metal nitrides Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-18368 ER - TY - THES A1 - Bäckemo, Johan Dag Valentin T1 - Digital tools and bioinspiration for the implementation in science and medicine T1 - Digitale Werkzeuge und Bioinspiration für die Umsetzung in der Wissenschaft und der Medizin N2 - Diese Doktorarbeit untersucht anhand dreier Beispiele, wie digitale Werkzeuge wie Programmierung, Modellierung, 3D-Konstruktions-Werkzeuge und additive Fertigung in Verbindung mit einer auf Biomimetik basierenden Design\-strategie zu neuen Analysemethoden und Produkten führen können, die in Wissenschaft und Medizin Anwendung finden. Das Verfahren der Funkenerosion (EDM) wird häufig angewandt, um harte Metalle zu verformen oder zu formen, die mit normalen Maschinen nur schwer zu bearbeiten sind. In dieser Arbeit wird eine neuartige Krümmungsanalysemethode als Alternative zur Rauheitsanalyse vorgestellt. Um besser zu verstehen, wie sich die Oberfläche während der Bearbeitungszeit des EDM-Prozesses verändert, wurde außerdem ein digitales Schlagmodell erstellt, das auf einem ursprünglich flachen Substrat Krater auf Erhebungen erzeugte. Es wurde festgestellt, dass ein Substrat bei etwa 10.000 Stößen ein Gleichgewicht erreicht. Die vorgeschlagene Krümmungsanalysemethode hat das Potenzial, bei der Entwicklung neuer Zellkultursubstrate für die Stammzellenforschung eingesetzt zu werden. Zwei Arten, die in dieser Arbeit aufgrund ihrer interessanten Mechanismen analysiert wurden, sind die Venusfliegenfalle und der Bandwurm. Die Venusfliegenfalle kann ihr Maul mit einer erstaunlichen Geschwindigkeit schließen. Der Schließmechanismus kann für die Wissenschaft interessant sein und ist ein Beispiel für ein so genanntes mechanisch bi-stabiles System - es gibt zwei stabile Zustände. Der Bandwurm ist bei Säugetieren meist im unteren Darm zu finden und heftet sich mit seinen Saugnäpfen an die Darmwände. Wenn der Bandwurm eine geeignete Stelle gefunden hat, stößt er seine Haken aus und heftet sich dauerhaft an die Wand. Diese Funktion könnte in der minimalinvasiven Medizin genutzt werden, um eine bessere Kontrolle der Implantate während des Implantationsprozesses zu ermöglichen. Für beide Projekte wurde ein mathematisches Modell, das so genannte Chained Beam Constraint Model (CBCM), verwendet, um das nichtlineare Biegeverhalten zu modellieren und somit vorherzusagen, welche Strukturen ein mechanisch bi-stabiles Verhalten aufweisen könnten. Daraufhin konnten zwei Prototypen mit einem 3D-Drucker gedruckt und durch Experimente veranschaulicht werden, dass sie beide ein bi-stabiles Verhalten aufweisen. Diese Arbeit verdeutlicht das hohe Anwendungspotenzial für neue Analysenmethoden in der Wissenschaft und für neue Medizinprodukte in der minimalinvasiven Medizin. N2 - Biomimicry is the art of mimicking nature to overcome a particular technical or scientific challenge. The approach studies how evolution has found solutions to the most complex problems in nature. This makes it a powerful method for science. In combination with the rapid development of manufacturing and information technologies into the digital age, structures and material that were before thought to be unrealizable can now be created with simple sketch and the touch of a button. This doctoral thesis had as its primary goal to investigate how digital tools, such as programming, modelling, 3D-Design tools and 3D-Printing, with the help from biomimicry, could lead to new analysis methods in science and new medical devices in medicine. The Electrical Discharge Machining (EDM) process is applied commonly to deform or mold hard metals that are difficult to work using normal machinery. A workpiece submerged in an electrolyte is deformed while being in close vicinity to an electrode. When high voltage is put between the workpiece and the electrode it will cause sparks that create cavitations on the substrate which in turn removes material and is flushed away by the electrolyte. Usually, such surfaces are analysed based on roughness, in this work another method using a novel curvature analysis method is presented as an alternative. In addition, to better understand how the surface changes during process time of the EDM process, a digital impact model was created which created craters on ridges on an originally flat substrate. These substrates were then analysed using the curvature analysis method at different processing times of the modelling. It was found that a substrate reaches an equilibrium at around 10000 impacts. The proposed curvature analysis method has potential to be used in the design of new cell culture substrates for stem cell. The Venus flytrap can shut its jaws at an amazing speed. The shutting mechanism may be interesting to use in science and is an example of a so-called mechanical bi-stable system – there are two stable states. In this work two truncated pyramid structures were modelled using a non-linear mechanical model called the Chained Beam Constraint Model (CBCM). The structure with a slope angle of 30 degrees is not bi-stable and the structure with a slope angle of 45 degrees is bi-stable. Developing this idea further by using PEVA, which has a shape-memory effect, the structure which is not bi-stable could be programmed to be bi-stable and then turned off again. This could be used as an energy storage system. Another species which has interesting mechanism is the tapeworm. Some species of this animal has a crown of hooks and suckers located on its side. The parasite commonly is found in mammals in the lower intestine and attaches to the walls by using its suckers. When the tapeworm has found a suitable spot, it ejects its hooks and permanently attaches to the wall. This function could be used in minimally invasive medicine to have better control of implants during the implantation process. By using the CBCM model and a 3D-printer capable of tuning how hard or soft a printed part is, a design strategy was developed to investigate how one could create a device that mimics the tapeworm. In the end a prototype was created which was able attach to a pork loin at an under pressure of 20 kPa and to ejects its hooks at an under pressure of 50 kPa or above. These three projects is an exhibit of how digital tools and biomimicry can be used together to come up with applicable solutions in science and in medicine. KW - bioinspiration KW - non-linear mechanics KW - modelling KW - shape-memory KW - additive manufacturing KW - Bioinspiration KW - nichtlineare Mechanik KW - Modellierung KW - Formgedächtnis KW - additive Fertigung Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-571458 ER - TY - THES A1 - Cao, Qian T1 - Graphitic carbon nitride and polymer hybrid materials BT - a promising combination for advanced properties N2 - Advanced hybrid materials are recognized as one of the most significant enablers for new technologies, which holds true especially on the quest for sustainable energy sources and energy production schemes (e.g., semiconductor based photocatalytic materials). Usually, a single component is far from meeting all the demands needed for these advanced applications. Hybrid materials are composed of at least two components commonly an inorganic and an organic material on the molecular level, which feature novel properties exceeding the sum of the individual parts and might be the milestones of next-generation applications. This dissertation aims to provide novel combinations of the metal-free semiconductor graphitic carbon nitride (g-C3N4) with polymers to obtain materials with advanced properties and applications. Visible light constitutes the core of the present work as it is the only energy source utilized either in synthesis or in the application process. In the area of applications by combination of g-C3N4 and polymers, two different hybrids were thoroughly elucidated, i.e.. their design and construction as well as potential application in photocatalysis. Novel soft 3D liquid objects were formed via charge-interaction driven interfacial jamming between polyelectrolytes in aqueous environment and colloidal dispersions of g-C3N4 in edible sunflower oil. As such, stable liquid objects could be molded into specific shapes and utilized for photodegradation of organic dyes in water. Furthermore, the grafting of polymers onto g-C3N4 was investigated. Allyl-end functionalized polymers were grafted onto g-C3N4 by a photoinitiated process to yield g-C3N4 with versatile and improved properties, e.g. advanced dispersibility enabling processing via spin coating. As g-C3N4 produces radicals under visible light irradiation, which is of significant interest for polymer science, g-C3N4 containing polymer latex and macrogel beads (MGB) were synthesized by emulsion photopolymerization and inverse suspension photopolymerization, respectively. A well-controlled emulsion photopolymerization process via g-C3N4 initiation was designed, which features synthesis of well-defined and cross-linked polymer particles. Furthermore, the polymerization process was investigated thoroughly, indicating an ad-layer polymerization in early stages of the process. The utilization of functionalized g-C3N4 allowed the polymerization of various monomer types. Moreover, g-C3N4 was utilized as photoinitiator in hydrogel MGB formation. The formed MGB properties could be tailored via process design, e.g. stirring rate, cross-linker content and g-C3N4 content. Finally, MGBs were introduced as photocatalyst for waste water remediation, i.e. the degradation of Rhodamine B in aqueous solution was studied. The present thesis therefore builds a bridge between g-C3N4 and polymers and provides strategies for hybrid material formation. Furthermore, several potential applications are revealed with significant implications for photocatalysis, polymerization processes and polymer materials. KW - Graphitic carbon nitride KW - Hybrid materials synthesis KW - Polymers KW - Photopolymerization Y1 - 2020 ER - TY - THES A1 - Cataldo, Vincenzo Alessandro T1 - Design and synthesis of alkylating ionic liquids and their application in synthesis, materials and proteomics Y1 - 2020 ER - TY - THES A1 - Cerdá Doñate, Elisa T1 - Microfluidics for the study of magnetotactic bacteria towards single-cell analysis N2 - Magnetotactic bacteria comprise a heterogeneous group of Gram negative bacteria which share the ability to synthesise intracellular magnetic nanoparticles surrounded by a lipid bilayer, known as magnetosomes, which are arranged in linear chains. The bacteria exert a unique level of control onto the biomineralization of these nanoparticles, which is seen in the controlled size and shape they have. These characteristics have attracted great attention on understanding the process by which the bacteria synthesise the magnetosomes. Moreover, the magnetosome chain impart the bacteria with a net magnetic dipole which makes them susceptible to interact with magnetic fields and thus orient with the Earth’s magnetic field. This feature has attracted as well much interest to understand how the swimming motility of these microorganisms is affected by the presence of magnetic fields. Most of the studies performed in these bacteria so far have been conducted in the traditional manner using large populations of cells. Such studies have the disadvantage of averaging many different individuals with heterogeneous behaviours and fail to consider individual variations. In addition, in large populations each bacterium will be subjected to a different microenvironment that will influence the bacterial behaviour, but which cannot be defined using these traditional methods. In this thesis, different microfluidic platforms are proposed to overcome these limitations and to offer the possibility to study magnetotactic bacteria in defined environments and down to a single-cell resolution. First, a sediment-like microfluidic platform is presented with the purpose of mimicking the porous environment they bacteria naturally dwell in. The platform allows to observe via transmitted light microscopy that bacterial navigation in crowded environments is enhanced by the Earth’s magnetic field strengths (B = 50 μT) rather than by null (B = 0 μT) or higher magnetic fields (B = 500 μT). Second, a microfluidic system to confine single-bacterial cells in physically defined environments is presented. The system allows to study via transmitted light microscopy the interplay between wall curvature, magnetic fields and bacterial speed affect the motion of a confined bacterium, and shows how bacterial trajectories depend on those three parameters. Third, a microfluidic platform to conduct semi in vivo magnetosome nucleation with a single-cell resolution via X-ray fluorescence is fabricated. It is shown that signal arising from magnetosome full chains can be observed individually in each bacterium. Finally, the iron uptake kinetics of a single bacterium are studied via a fluorescent reporter through confocal microscopy. Two different approaches are used for this: one of the previously mentioned platforms, as well as giant lipid vesicles. It is observed how iron uptake rates vary between cells, as well as how these rates are consistent with magnetosome formation taking place within some hours. The present thesis shows therefore how microfluidic technologies can be implemented for the study of magnetotactic bacteria at different degrees, and the level of resolution that can be attained by going into the single- cell scale.
 N2 - Magnetotaktische Bakterien gehören einer heterogenen Gruppe gramnegativer Bakterien an, welche die Fähigkeit zur Synthese intrazellulärer magnetischer Nanopartikel teilen. Diese Partikel, genannt Magnetosomen, sind von einer Doppellipidschicht umgeben und ordnen sich in linearen Ketten an. Die Bakterien haben ein einzigartiges Maß an Kontrolle über die Biomineralisation dieser Nanopartikel, welche sich in der genau bestimmten Größe und Form zeigt. Diese besonderen Eigenschaften haben die Aufmerksamkeit auf ein besseres Verständnis der Magnetosomensynthese durch die Bakteriengezogen. Darüber hinaus besitzen die Bakterien durch die Magnetosomenkette ein magnetisches Dipolmoment, welches sie befähigt auf ein Magnetfeld zu reagieren, wodurch sie sich im Magnetfeld der Erde ausrichten können. Auch diese Eigenschaft hat großes Interesse geweckt, besonders um den Einfluss eines Magnetfeldes auf das Schwimmverhalten der Mikroorganismen besser zu verstehen. Die meisten bisherigen Studien an diesen Organismen wurden in klassischen Systemen mit großen Populationen durchgeführt. Solche Studien haben den Nachteil, dass das heterogene Verhalten vieler verschiedener Individuen gemittelt wird und daher individuelle Variationen nicht berücksichtigt werden. Zusätzlich ist jedes einzelne Bakterium einer großen Population einer anderen Mikroumgebung ausgesetzt, welche sein Verhalten beeinflusst, das aber durch die Verwendung traditioneller Methoden nicht erfasst werden kann. In dieser Arbeit werden verschiedene mikrofluidische Plattformen vorgestellt, um diese Einschränkungen zu überwinden und die Möglichkeit zu bieten, sogar einzelne magnetotaktische Bakterien in einer definierten Umgebung studieren zu können. Als erstes wird eine Sediment-ähnliche mikrofluidische Plattform vorgestellt, die den Zweck hat, die natürliche poröse Umgebung der Bakterien zu imitieren. Die Plattform erlaubt es mit Hilfe von Durchlichtmikroskopie zu sehen, dass Bakterien in einer gedrängten Umgebung eine verbesserte Navigation im Bereich der Erdmagnetfeldstärke (B = 50 μT) haben, im Vergleich zu keinem (B = 0 μT) oder einem höheren Magnetfeld 
 (B = 50μT). Zweitens wurde ein mikrofluidisches System zum Eingrenzen einzelner Bakterien in einer physisch definierten Umgebung entwickelt. Das System erlaubt mit Hilfe von Durchlichtmikroskopie die Untersuchung des Einflusses und des Zusammenspiels von Wandkrümmung, Magnetfeld und Bakteriengeschwindigkeit auf die Bewegung eines eingegrenzten Bakteriums und zeigt, wie die Bewegungspfade der Bakterien von diesen drei Faktoren abhängen. Drittens wurde eine mikrofluidische Plattform hergestellt, die die Durchführung von semi in-vivo Magnetosomenkeimbildung mit einer Auflösung von einzelnen Zellen mittels Röntgenfluoreszenz ermöglicht. Signale, welche von einer kompletten Magnetosomenkette herrühren, können in individuellen Bakterien beobachtet werden. Abschließend wurde die Kinetik der Eisenaufnahme eines einzelnen Bakteriums durch einen fluoreszierenden Reporter mit Hilfe von konfokaler Mikroskopie untersucht. Zwei verschiedenen Ansätze wurden dabei verwendet: eine der bereits vorgestellten Plattformen, sowie riesige Lipidvesikel. Es wurde beobachtet, dass die Eisenaufnahmerate zwischen verschiedenen Zellen variiert und wie sich damit übereinstimmend Magnetosomen innerhalb von Stunden bilden. Diese Arbeit zeigt damit wie mikrofluidische Technologien für die Untersuchung magnetotaktischer Bakterien in unterschiedlichen Bereichen eingesetzt werden können, und welches Level an Auflösung erreicht werden kann, indem mit einzelnen Zellen gearbeitet wird.
 KW - Magnetotactic bacteria KW - microfluidics KW - single-cell KW - iron KW - microscopy Y1 - 2020 ER - TY - THES A1 - Chaleawlert-Umpon, Saowaluk T1 - Sustainable electrode materials based on lignin T1 - Ligninbasierte nachhaltige Elektrodenmaterialien N2 - The utilization of lignin as renewable electrode material for electrochemical energy storage is a sustainable approach for future batteries and supercapacitors. The composite electrode was fabricated from Kraft lignin and conductive carbon and the charge storage contribution was determined in terms of electrical double layer (EDL) and redox reactions. The important factors at play for achieving high faradaic charge storage capacity contribute to high surface area, accessibility of redox sites in lignin and their interaction with conductive additives. A thinner layer of lignin covering the high surface area of carbon facilitates the electron transfer process with a shorter pathway from the active sites of nonconductive lignin to the current collector leading to the improvement of faradaic charge storage capacity. Composite electrodes from lignin and carbon would be even more sustainable if the fluorinated binder can be omitted. A new route to fabricate a binder-free composite electrode from Kraft lignin and high surface area carbon has been proposed by crosslinking lignin with glyoxal. A high molecular weight of lignin is obtained to enhance both electroactivity and binder capability in composite electrodes. The order of the processing step of crosslinking lignin on the composite electrode plays a crucial role in achieving a stable electrode and high charge storage capacity. The crosslinked lignin based electrodes are promising since they allow for more stable, sustainable, halogen-free and environmentally benign devices for energy storage applications. Furthermore, improvement of the amount of redox active groups (quinone groups) in lignin is useful to enhance the capacity in lithium battery applications. Direct oxidative demethylation by cerium ammonium nitrate has been carried out under mild conditions. This proves that an increase of quinone groups is able to enhance the performance of lithium battery. Thus, lignin is a promising material and could be a good candidate for application in sustainable energy storage devices. N2 - Die Verwendung von Lignin als erneuerbares Ausgangsmaterial für Elektroden ist ein nachhaltiger Ansatz für die Herstellung der nächsten Generation von Batterien und Superkondensatoren. In dieser Arbeit werden Verbundelektroden auf der Basis von Kraft-Lignin und leitfähigem Kohlenstoff hergestellt und getestet. Die Beiträge des Aufbaus einer elektrischen Doppelschicht (EDL) und der Redoxreaktionen zur Kapazität der Elektrode werden diskutiert. Die wichtigsten Faktoren um eine hohe faradaysche Kapazität der aktiven Gruppen in Lignin zu erreichen sind eine große Oberfläche, die Zugänglichkeit der redoxaktiven Gruppen, sowie die Wechselwirkung mit leitfähigen Additiven. Dabei verringert eine dünnere Ligninschicht auf der Oberfläche des leitfähigen Kohlenstoffs den Elektronentransportweg zwischen den redoxaktiven Gruppen und dem Stromabnehmer und wirkt sich somit positiv auf die faradaysche Kapazität aus. Traditionelle Verbundelektroden enthalten in der Regel fluorierte Bindemittel, was deren Nachhaltigkeit in Frage stellt. Die Verwendung von Glyoxal als Quervernetzer für Lignin stellt eine Alternative zur Herstellung von bindemittelfreien ligninbasierten Verbundelektroden dar. Durch die Quervernetzung wird Lignin mit hohem Molekulargewicht erhalten, was sich insbesondere vorteilhaft auf die Stabilität der Elektroden auswirkt. Für das Erreichen einer hohen Kapazität spielt allerdings die Reihenfolge der Produktionsschritte eine entscheidende Rolle, was hier auch diskutiert wird. Eine Erhöhung der Anzahl an redoxativen Gruppen, insbesondere Chinon-Funktionalitäten, im Lignin führt darüber hinaus zur Erhöhung der Kapazität in primären Lithiumbatterien. Die direkte oxidative Demethylierung von Phenylethern mit Hilfe von Cerammoniumnitrat wurde in dieser Arbeit unter milden Reaktionsbedingungen durchgeführt und die verbesserte Kapazität in Lithiumbatterien aufgrund der erhöhten Anzahl an redoxaktiven Gruppen aufgezeigt. Abschließend kann Lignin, quervernetzt oder oxidiert, als vielversprechender Wegbereiter für nachhaltige Materialen in der Energiespeicherung angesehen werden. KW - lignin KW - energy storage KW - sustainable energy storage materials KW - Lignin KW - Energiespeicher KW - nachhaltige Energiespeichermaterialien Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-411793 ER - TY - THES A1 - Chanana, Munish T1 - Synthesis of stimuli-responsive and switchable inorganic nanoparticles for biomedical applications Y1 - 2010 CY - Potsdam ER - TY - THES A1 - Chandrakanth Shetty, Sunidhi T1 - Directed chemical communication in artificial eukaryotic cells T1 - Gezielte chemische Kommunikation in künstlichen eukaryotischen Zellen N2 - Eukaryotic cells can be regarded as complex microreactors capable of performing various biochemical reactions in parallel which are necessary to sustain life. An essential prerequisite for these complex metabolic reactions to occur is the evolution of lipid membrane-bound organelles enabling compartmental- ization of reactions and biomolecules. This allows for a spatiotemporal control over the metabolic reactions within the cellular system. Intracellular organi- zation arising due to compartmentalization is a key feature of all living cells and has inspired synthetic biologists to engineer such systems with bottom-up approaches. Artificial cells provide an ideal platform to isolate and study specific re- actions without the interference from the complex network of biomolecules present in biological cells. To mimic the hierarchical architecture of eukaryotic cells, multi-compartment assemblies with nested liposomal structures also re- ferred to as multi-vesicular vesicles (MVVs) have been widely adopted. Most of the previously reported multi-compartment systems adopt bulk method- ologies which suffer from low yield and poor control over size. Microfluidic strategies help circumvent these issues and facilitate a high-throughput and robust technique to assemble MVVs of uniform size distribution. In this thesis, firstly, the bulk methodologies are explored to build MVVs and implement a synthetic signalling cascade. Next, a polydimethylsiloxane (PDMS)-based microfluidic platform is introduced to build MVVs and the significance of PEGylated lipids for the successful encapsulation of inner com- partments to generate stable multi-compartment systems is highlighted. Next, a novel two-inlet channel PDMS-based microfluidic device to create MVVs encompassing a three-step enzymatic reaction cascade is presented. A directed reaction pathway comprising of the enzymes α-glucosidase (α-Glc), glucose oxidase (GOx), and horseradish peroxidase (HRP) spanning across three compartments via reconstitution of size-selective membrane proteins is described. Furthermore, owing to the monodispersity of our MVVs due to microfluidic strategies, this platform is employed to study the effect of com- partmentalization on reaction kinetics. Further integration of cell-free expression module into the MVVs would allow for gene-mediated signal transduction within artificial eukaryotic cells. Therefore, the chemically inducible cell-free expression of a membrane protein alpha-hemolysin and its further reconstitution into liposomes is carried out. In conclusion, the present thesis aims to build artificial eukaryotic cells to achieve size-selective chemical communication that also show potential for applications as micro reactors and as vehicles for drug delivery. N2 - Eukaryontische Zellen können als komplexe Mikroreaktoren betrachtet werden, die in der Lage sind, verschiedene biochemische Reaktionen parallel durchzuführen, die für die Aufrechterhaltung des Lebens notwendig sind. Eine wesentliche Voraussetzung für die Durchführung dieser komplexen Stoffwechselreaktionen ist die Entwicklung von Organellen mit Lipidmembranen, die eine Kompartimentierung von Reaktionen und Biomolekülen ermöglichen. Dies ermöglicht eine räumlich-zeitliche Kontrolle über die Stoffwechselreaktionen innerhalb des zellulären Systems. Die durch die Kompartimentierung entstehende intrazelluläre Organisation ist ein Schlüsselmerkmal aller lebenden Zellen und hat synthetische Biologen dazu inspiriert, solche Systeme mit Bottom-up-Ansätzen zu entwickeln. Künstliche Zellen bieten eine ideale Plattform, um spezifische Reaktionen zu isolieren und zu untersuchen, ohne dass das komplexe Netzwerk von Biomolekülen, das in biologischen Zellen vorhanden ist, stört. Um die hierarchische Architektur eukaryontischer Zellen zu imitieren, haben sich Multikompartiment-Anordnungen mit verschachtelten liposomalen Strukturen, die auch als multivesikuläre Vesikel (MVV) bezeichnet werden, durchgesetzt. Die meisten der bisher vorgestellten Multikompartiment-Systeme basieren auf Bulk-Methoden, die eine geringe Ausbeute und eine schlechte Kontrolle über die Größe aufweisen. Mikrofluidische Strategien helfen, diese Probleme zu umgehen und ermöglichen eine robuste Technik mit hohem Durchsatz, um MVVs mit einheitlicher Größenverteilung herzustellen. In dieser Dissertation werden zunächst die Bulk-Methoden zum Aufbau von MVVs und zur Implementierung einer synthetischen Signalkaskade untersucht. Anschließend wird eine auf Polydimethylsiloxan (PDMS) basierende mikrofluidische Plattform zur Herstellung von MVVs vorgestellt und die Bedeutung von PEGylierten Lipiden für die erfolgreiche Verkapselung der inneren Kompartimente zur Erzeugung stabiler Multikompartiment-Systeme hervorgehoben. Es wird ein neuartiges mikrofluidisches Gerät mit zwei Einlasskanälen auf PDMS-Basis zur Herstellung von MVVs vorgestellt, das eine dreistufige enzymatische Reaktionskaskade umfasst. Es wird ein gerichteter Reaktionsweg beschrieben, der die Enzyme α-Glucosidase (α-Glc), Glucoseoxidase (GOx) und Meerrettichperoxidase (HRP) umfasst und sich über drei Kompartimente erstreckt, die durch die Rekonstitution von größenselektiven Membranproteinen entstehen. Aufgrund der Monodispersität unserer MVVs durch mikrofluidische Strategien nutze ich diese Plattform außerdem, um die Auswirkungen der Kompartimentierung auf die Reaktionskinetik zu untersuchen. Eine weitere Integration von zellfreien Expressionsmodulen in MVVs würde eine genvermittelte Signaltransduktion in künstlichen eukaryotischen Zellen ermöglichen. Daher wird die chemisch induzierbare zellfreie Expression eines Membranproteins alpha-Hämolysin und seine weitere Rekonstitution in Liposomen durchgeführt. Zusammenfassend lässt sich sagen, dass die vorliegende Arbeit darauf abzielt, künstliche eukaryotische Zellen zu bauen, um eine größenselektive chemische Kommunikation zu erreichen, und das Potenzial für Anwendungen als Mikroreaktoren und als Vehikel für die Verabreichung von Medikamenten aufweisen. KW - microfluidics KW - synthetic biology KW - Mikrofluidik KW - synthetische Biologie Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-533642 ER - TY - THES A1 - Charan, Himanshu T1 - Self assembled transmembrane protein polymer conjugates for the generation of nano thin membranes and micro compartments T1 - Selbstassemblierte Transmembranprotein-Polymer Konjugate für die Herstellung von nanodünnen Membranen und Mikrokompartimenten N2 - This project was focused on generating ultra thin stimuli responsive membranes with an embedded transmembrane protein to act as the pore. The membranes were formed by crosslinking of transmembrane protein polymer conjugates. The conjugates were self assembled on air water interface and the polymer chains crosslinked using a UV crosslinkable comonomer to engender the membrane. The protein used for the studies reported herein was one of the largest transmembrane channel proteins, ferric hydroxamate uptake protein component A (FhuA), found in the outer membrane of Escherichia coli (E. coli). The wild type protein and three genetic variants of FhuA were provided by the group of Prof. Schwaneberg in Aachen. The well known thermo responsive poly(N isopropylacrylamide) (PNIPAAm) and the pH and thermo responsive polymer poly((2-dimethylamino)ethyl methacrylate) (PDMAEMA) were conjugated to FhuA and the genetic variants via controlled radical polymerization (CRP) using grafting from technique. These polymers were chosen because they would provide stimuli handles in the resulting membranes. The reported polymerization was the first ever attempt to attach polymer chains onto a membrane protein using site specific modification. The conjugate synthesis was carried out in two steps – a) FhuA was first converted into a macroinitiator by covalently linking a water soluble functional CRP initiator to the lysine residues. b) Copper mediated CRP was then carried out in pure buffer conditions with and without sacrificial initiator to generate the conjugates. The challenge was carrying out the modifications on FhuA without denaturing it. FhuA, being a transmembrane protein, requires amphiphilic species to stabilize its highly hydrophobic transmembrane region. For the experiments reported in this thesis, the stabilizing agent was 2 methyl 2,4-pentanediol (MPD). Since the buffer containing MPD cannot be considered a purely aqueous system, and also because MPD might interfere with the polymerization procedure, the reaction conditions were first optimized using a model globular protein, bovine serum albumin (BSA). The optimum conditions were then used for the generation of conjugates with FhuA. The generated conjugates were shown to be highly interfacially active and this property was exploited to let them self assemble onto polar apolar interfaces. The emulsions stabilized by particles or conjugates are referred to as Pickering emulsions. Crosslinking conjugates with a UV crosslinkable co monomer afforded nano thin micro compartments. Interfacial self assembly at the air water interface and subsequent UV crosslinking also yielded nano thin, stimuli responsive membranes which were shown to be mechanically robust. Initial characterization of the flux and permeation of water through these membranes is also reported herein. The generated nano thin membranes with PNIPAAm showed reduced permeation at elevated temperatures owing to the resistance by the hydrophobic and thus water-impermeable polymer matrix, hence confirming the stimulus responsivity. Additionally, as a part of collaborative work with Dr. Changzhu Wu, TU Dresden, conjugates of three enzymes with current/potential industrial relevance (candida antarctica lipase B, benzaldehyde lyase and glucose oxidase) with stimuli responsive polymers were synthesized. This work aims at carrying out cascade reactions in the Pickering emulsions generated by self assembled enzyme polymer conjugate. N2 - Im Rahmen dieses Projekts wurden ultradünne Stimuli responsive Membranen hergestellt, in die ein Transmembranprotein als Pore eingebettet ist. Die Membranen wurden durch das Verlinken von Transmembranprotein-Polymer Konjugaten an Grenzflächen hergestellt. Dazu wurden Konjugate an der Luft-Wasser-Grenzfläche selbstassembliert und die Polymerketten unter Verwendung eines UV-vernetzbaren Comonomers vernetzt. Als Protein wurde einer der größten Transmembran-Proteinkanäle, welcher sich in der Natur in der äußeren Membran von Escherichia coli (E. coli) findet, verwendet, nämlich ferric hydroxamate uptake protein component A (FhuA). Das Wildtyp-Protein und drei genetische Varianten von FhuA wurden von der Gruppe von Prof. Schwaneberg in Aachen zur Verfügung gestellt. Das bekannte thermo responsive Poly(N-isopropylacrylamid) (PNIPAAm) und das pH- und thermo responsive Polymer Poly((2-dimethylamino) ethylmethacrylat) (PDMAEMA) wurden über kontrollierte radikalische Polymerisationen (CRP) via der grafting-from Technik an FhuA und die genetischen Varianten konjugiert. Diese responsiven Polymere wurden ausgewählt, weil die Eigenschaften der resultierenden Membranen folglich durch äußere Einflusse verändert werden können. Dabei handelt es sich um das erste Beispiel, Polymerketten von einem Membranprotein ortsspezifisch zu synthetisieren. Die Konjugatsynthese wurde in zwei Schritten durchgeführt - a) zuerst wurde ein FhuA Makroinitiator durch Anbinden funktioneller CRP Initiatoren an die Lysinreste des Proteins dargestellt. B) durch Kupfer-vermittelte CRP wurden dann in Pufferlösung sowohl mit als auch ohne Opferinitiator die Konjugate synthetisiert. Die Herausforderung bestand darin, FhuA zu modifizieren ohne das Protein dabei zu denaturieren. Als Transmembranprotein benötigt FhuA amphiphile Agentien, um seine hydrophobe Transmembran Region zu stabilisieren. Für die im Rahmen dieser Arbeit durchgeführten Experimente war das stabilisierende Agens 2-Methyl-2,4-pentandiol (MPD). Da der MPD-Puffer nicht als rein wässriges Medium betrachtet werden kann, und auch, weil MPD das Polymerisationsverfahren beeinflussen könnte, wurden die Reaktionsbedingungen zunächst unter Verwendung eines globulären Modellproteins, nämlich Rinderserumalbumin (BSA), optimiert. Die optimalen Bedingungen wurden dann für die Erzeugung von Konjugaten mit FhuA verwendet. Die Konjugate zeigten eine hohe Grenzflächenaktivität und diese Eigenschaft wurde für die Selbstassemblierung an polaren/apolaren Grenzflächen ausgenutzt. Wurden Emulsionen durch die Konjugate stabilisiert, so bezeichnet man dies als Pickering-Emulsionen. Das Vernetzen von Konjugaten mit einem UV-vernetzbaren Co-Monomer führt zu nano-dünnen Mikrokompartimenten. Die Selbstassemblierung an der Luft-Wasser-Grenzfläche und anschließende UV-Vernetzung ergaben nano-dünne, Stimuli-responsive Membranen, die sich als mechanisch robust erwiesen. Eine erste Charakterisierung des Flusses und der Permeation von Wasser durch die Membranen wird ebenfalls in dieser Arbeit beschrieben. Die erzeugten nano dünnen Membranen mit PNIPAAm zeigten eine verminderte Permeation bei erhöhten Temperaturen aufgrund der nun hydrophoben und damit wasserundurchlässigen Polymermatrix. Darüber hinaus wurden für eine Kooperation mit Dr. Changzhu Wu, TU Dresden, Konjugate von drei Enzymen mit industrieller Relevanz (Candida antarctica Lipase B, Benzaldehydlyase und Glucose-Oxidase) synthetisiert. Diese Arbeit zielt auf Kaskadenreaktionen in Pickering-Emulsionen, die durch selbstassemblierte Enzym-Polymer Konjugate katalysiert werden. KW - FhuA KW - transmembrane protein KW - protein-polymer conjugate KW - controlled radical polymerization KW - ultra-thin membrane KW - FhuA KW - Transmembranprotein KW - Protein-Polymer Konjugaten KW - kontrollierte radikalische Polymerisationen KW - ultradünne Membranen Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-402060 SP - xii, 138 ER - TY - THES A1 - Chea, Sany T1 - Glycomaterials: From synthesis of glycoconjugates to potential biomedical applications T1 - Glykomaterialien: Von der Synthese von Glykokonjugaten zu potenziellen biomedizinischen Anwendungen N2 - The importance of carbohydrate structures is enormous due to their ubiquitousness in our lives. The development of so-called glycomaterials is the result of this tremendous significance. These are not exclusively used for research into fundamental biological processes, but also, among other things, as inhibitors of pathogens or as drug delivery systems. This work describes the development of glycomaterials involving the synthesis of glycoderivatives, -monomers and -polymers. Glycosylamines were synthesized as precursors in a single synthesis step under microwave irradiation to significantly shorten the usual reaction time. Derivatization at the anomeric position was carried out according to the methods developed by Kochetkov and Likhorshetov, which do not require the introduction of protecting groups. Aminated saccharide structures formed the basis for the synthesis of glycomonomers in β-configuration by methacrylation. In order to obtain α-Man-based monomers for interactions with certain α-Man-binding lectins, a monomer synthesis by Staudinger ligation was developed in this work, which also does not require protective groups. Modification of the primary hydroxyl group of a saccharide was accomplished by enzyme-catalyzed synthesis. Ribose-containing cytidine was transesterified using the lipase Novozym 435 and microwave irradiation. The resulting monomer synthesis was optimized by varying the reaction partners. To create an amide bond instead of an ester bond, protected cytidine was modified by oxidation followed by amide coupling to form the monomer. This synthetic route was also used to isolate the monomer from its counterpart guanosine. After obtaining the nucleoside-based monomers, they were block copolymerized using the RAFT method. Pre-synthesized pHPMA served as macroCTA to yield cytidine- or guanosine-containing block copolymer. These isolated block copolymers were then investigated for their self-assembly behavior using UV-Vis, DLS and SEM to serve as a potential thermoresponsive drug delivery system. N2 - Die Bedeutung von Kohlenhydratstrukturen ist immens, da sie in unserem Leben allgegenwärtig sind. Die Entwicklung sogenannter Glykomaterialien ist das Ergebnis dieser großen Bedeutung. Diese werden nicht nur zur Erforschung grundlegender biologischer Prozesse eingesetzt, sondern unter anderem auch als Hemmstoffe für Krankheitserreger oder als Wirkstofftransportsysteme. Die vorliegende Arbeit beschreibt die Entwicklung von Glycomaterialien durch die Synthese von Glycoderivaten, -monomeren und -polymeren. Glycosylamine wurden als Vorstufen in einem einzigen Syntheseschritt unter Mikrowellenbestrahlung synthetisiert, um die übliche Reaktionszeit deutlich zu verkürzen. Die Derivatisierung an der anomeren Position wurde nach den von Kochetkov und Likhorshetov entwickelten Methoden durchgeführt, die keine Einführung von Schutzgruppen erfordern. Die aminierten Saccharidstrukturen bildeten die Grundlage für die Synthese von Glycomonomeren in β-Konfiguration durch Methacrylierung. Um α-Man-basierte Monomere für Interaktionen mit bestimmten α-Man-bindenden Lektinen zu erhalten, wurde in dieser Arbeit eine Monomersynthese durch Staudinger-Ligation entwickelt, die ebenfalls keine Schutzgruppen erfordert. Die Modifizierung der primären Hydroxylgruppe eines Saccharids wurde durch enzymkatalysierte Synthese erreicht. Ribosehaltiges Cytidin wurde mit Hilfe der Lipase Novozym 435 und Mikrowellenbestrahlung umgeestert. Die resultierende Monomersynthese wurde durch Variation der Reaktionspartner optimiert. Um eine Amidbindung anstelle einer Esterbindung zu erzeugen, wurde geschütztes Cytidin durch Oxidation und anschließende Amidkupplung modifiziert, um das Monomer zu bilden. Dieser Syntheseweg wurde auch zur Isolierung des Monomers aus seinem Gegenstück Guanosin verwendet. Nach der Gewinnung der nukleosidbasierten Monomere wurden diese mit Hilfe der RAFT-Methode blockcopolymerisiert. Vorsynthetisiertes pHPMA diente als MakroCTA, um Cytidin- oder Guanosin-haltige Blockcopolymere zu erhalten. Diese isolierten Blockcopolymere wurden dann mit UV-Vis, DLS und SEM auf ihr Selbstorganisationsverhalten untersucht, um als potenzielles thermoresponsives Drug-Delivery-System zu dienen. KW - polymer chemistry KW - glyco chemistry KW - glycomonomer KW - glycopolymer KW - lectin KW - drug delivery KW - thermoresponsive KW - glycoconjugate KW - Glykochemie KW - Glykokonjugat KW - Glykomonomer KW - Glykopolymer KW - Lektin KW - Polymerchemie KW - thermoresponsiv KW - Drug Delivery Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-574240 ER - TY - THES A1 - Chemura, Sitshengisiwe T1 - Optical spectroscopy on lanthanide-modified nanomaterials for performance monitoring T1 - Optische Spektroskopie an Lanthanid-modifizierten Nanomaterialien zur Leistungsüberwachung N2 - Lanthanide based ceria nanomaterials are important practical materials due to their redox properties that are useful in technology and life sciences. This PhD thesis examined various properties and potential for catalytic and bio-applications of Ln3+-doped ceria nanomaterials. Ce1-xGdxO2-y: Eu3+, gadolinium doped ceria (GDC) (0 ≤ x ≤ 0.4) nanoparticles were synthesized by flame spray pyrolysis (FSP) and studied, followed by 15 % CexZr1-xO2-y: Eu3+|YSZ (0 ≤ x ≤ 1) nanocomposites. Furthermore, Ce1-xYb xO2-y (0.004 ≤ x ≤ 0.22) nanoparticles were synthesized by thermal decomposition and characterized. Finally, CeO2-y: Eu3+ nanoparticles were synthesized by a microemulsion method, biofunctionalized and characterized. The studies undertaken presents a novel approach to structurally elucidate ceria-based nanomaterials by way of Eu3+ and Yb3+ spectroscopy and processing the spectroscopic data with the multi-way decomposition method PARAFAC. Data sets of the three variables: excitation wavelength, emission wavelength and time were used to perform the deconvolution of spectra. GDC nanoparticles from FSP are nano-sized and of roughly cubic shape and crystal structure (Fm3̅m). Raman data revealed four vibrational modes exhibited by Gd3+ containing samples whereas CeO2-y: Eu3+ displays only two. The room temperature, time-resolved emission spectra recorded at λexcitation = 464 nm show that Gd3+ doping results in significantly altered emission spectra compared to pure ceria. The PARAFAC analysis for the pure ceria samples reveals two species; a high-symmetry species and a low-symmetry species. The GDC samples yield two low-symmetry spectra in the same experiment. High-resolution emission spectra recorded at 4 K after probing the 5D0-7F0 transition revealed additional variation in the low symmetry Eu3+ sites in pure ceria and GDC. The data of the Gd3+-containing samples indicates that the average charge density around the Eu3+ ions in the lattice is inversely related to Gd3+ and oxygen vacancy concentration. The particle crystallites of the 773 K and 1273 K annealed Yb3+ -ceria nanostructure materials are nano-sized and have a cubic fluorite structure with four Raman vibrational modes. Elemental maps clearly show that cluster formation occurs for 773 K annealed with high Yb3+ ion concentration from 15 mol % in the ceria lattice. These clusters are destroyed with annealing to 1273 K. The emission spectra observed from room temperature and 4 K measurements for the Ce1-xYb xO2-y samples have a manifold that corresponds to the 2F5/2-2F7/2 transition of Yb3+ ions. Some small shifts are observed in the Stark splitting pattern and are induced by the variations of the crystal field influenced by where the Yb3+ ions are located in the crystal lattices in the samples. Upon mixing ceria with high Yb3+ concentrations, the 2F5/2-2F7/2 transition is also observed in the Stark splitting pattern, but the spectra consist of two broad high background dominated peaks. Annealing the nanomaterials at 1273 K for 2 h changes the spectral signature as new peaks emerge. The deconvolution yielded luminescence decay kinetics as well as the accompanying luminescence spectra of three species for each of the low Yb3+ doped ceria samples annealed at 773 K and one species for the 1273 K annealed samples. However, the ceria samples with high Yb3+ concentration annealed at the two temperatures yielded one species with lower decay times as compared to the Yb3+ doped ceria samples after PARAFAC analysis. Through the calcination of the nanocomposites at two high temperatures, the evolution of the emission patterns from specific Eu3+ lattice sites to indicate structural changes for the nanocomposites was followed. The spectroscopy results effectively complemented the data obtained from the conventional techniques. Annealing the samples at 773 K, resulted in amorphous, unordered domains whereas the TLS of the 1273 K nanocomposites reveal two distinct sites, with most red shifted Eu3+ species coming from pure Eu3+ doped ZrO2 on the YSZ support. Finally, for Eu3+ doped ceria, successful transfer from hydrophobic to water phase and subsequent biocompatibility was achieved using ssDNA. PARAFAC analysis for the Eu3+ in nanoparticles dispersed in toluene and water revealed one Eu3+ species, with slightly differing surface properties for the nanoparticles as far as the luminescence kinetics and solvent environments were concerned. Several functionalized nanoparticles conjugated onto origami triangles after hybridization were visualized by atomic force microscopy (AFM). Putting all into consideration, Eu3+ and Yb3+ spectroscopy was used to monitor the structural changes and determining the feasibility of the nanoparticle transfer into water. PARAFAC proves to be a powerful tool to analyze lanthanide spectra in crystalline solid materials and in solutions, which are characterized by numerous Stark transitions and where measurements usually yield a superposition of different emission contributions to any given spectrum. N2 - Ceroxid-Nanomaterialien auf Lanthanidbasis sind aufgrund ihrer Redox-Eigenschaften wichtige praktische Materialien, die in der Technik und den Biowissenschaften von Nutzen sind. In dieser Dissertation wurden verschiedene Eigenschaften und das Potenzial für katalytische und biologische Anwendungen von Ln3+-dotierten Ceroxid-Nanomaterialien untersucht. Ce1-xGdxO2-y:Eu3+, gadoliniumdotierte Ceroxid (GDC) (0.0 ≤ x ≤ 0.4) Nanopartikel wurden durch Flammenspray-Pyrolyse (FSP) synthetisiert und untersucht, gefolgt von 15 % CexZr1-xO2-y:Eu3+|YSZ (0 ≤ x ≤ 1) Nanokompositen. Außerdem wurden Ce1-xYbxO2-y (0.004 ≤ x ≤ 0.22) Nanopartikel durch thermische Zersetzung synthetisiert und charakterisiert. Schließlich wurden CeO2-y:Eu3+-Nanopartikel durch eine Mikroemulsionsmethode synthetisiert, biofunktionalisiert und charakterisiert. In den durchgeführten Studien wird ein neuartiger Ansatz zur Strukturaufklärung von Nanomaterialien auf Ceroxidbasis mittels Eu3+- und Yb3+-Spektroskopie und Verarbeitung der spektroskopischen Daten mit der Zerlegungsmethode PARAFAC vorgestellt. Für die Entfaltung der Spektren wurden Datensätze mit den drei Variablen Anregungswellenlänge, Emissionswellenlänge und Zeit verwendet. GDC-Partikel aus FSP sind Nanometer groß und besitzen eine grob kubische Form und Kristallstruktur (Fm3̅m). Raman-Daten zeigten vier Schwingungsmoden bei Gd3+-haltigen Proben, während CeO2-y:Eu3+ nur zwei aufweist. Die bei Raumtemperatur aufgezeichneten zeitaufgelösten Emissionsspektren bei λAnregung = 464 nm zeigen, dass die Gd3+-Dotierung im Vergleich zu reinem Ceroxid zu deutlich veränderten Emissionsspektren führt. Die PARAFAC-Analyse für die reinen Ceroxidproben zeigt zwei Spezies: eine hochsymmetrische Spezies und eine niedrigsymmetrische Spezies. Die GDC-Proben liefern im selben Experiment zwei niedrigsymmetrische Species. Hochauflösende Emissionsspektren, die bei 4 K nach der Untersuchung des 5D0-7F0-Übergangs aufgezeichnet wurden, ergaben zusätzliche Variationen bei den niedrigsymmetrischen Eu3+-Stellen in reinem Ceroxid und GDC. Die Daten der Gd3+-haltigen Proben deuten darauf hin, dass die durchschnittliche Ladungsdichte um die Eu3+-Ionen im Gitter in umgekehrter Beziehung zur Gd3+- und Sauerstoffleerstellen-Konzentration steht. Die Partikelkristallite der bei 773 K und 1273 K geglühten Yb3+-Ceroxid-Nanostrukturen sind nanoskalig und haben eine kubische Fluoritstruktur mit vier Raman-Schwingungsmoden. Elementverteilungen zeigen deutlich, dass sich bei 773 K, geglüht mit einer hohen Yb3+-Ionenkonzentration ab 15 Mol-% im Ceroxidgitter, Cluster bilden. Diese Cluster werden beim Glühen auf 1273 K zerstört. Die Emissionsspektren, die bei Messungen bei Raumtemperatur und 4 K für die Ce1-xYbxO2-y-Proben beobachtet wurden, weisen vielfältige Banden auf, die dem 2F5/2-2F7/2-Übergang der Yb3+-Ionen entspricht. Es werden einige kleine Verschiebungen im Stark-Aufspaltungsmuster beobachtet, die durch die Variationen des Kristallfeldes verursacht werden, in Abhängigkeit der Positionen der Yb3+-Ionen in den Kristallgittern. Beim Mischen von Ceroxid mit hohen Yb3+-Konzentrationen wird der 2F5/2-2F7/2-Übergang auch im Stark-Aufspaltungsmuster beobachtet, aber die Spektren bestehen aus zwei breiten, vom Hintergrund dominierten Peaks. Das Ausglühen der Nanomaterialien bei 1273 K für 2 Stunden verändert die spektrale Signatur, da neue Emissionsbanden entstehen. Die Entfaltung ergab die Lumineszenz-Abklingkinetik sowie die begleitenden Lumineszenzspektren von drei Spezies für jede der niedrig Yb3+-dotierten Ceroxidproben, die bei 773 K geglüht wurden, und eine Spezies für die bei 1273 K geglühten Proben. Die bei beiden Temperaturen geglühten Ceroxidproben mit hoher Yb3+-Konzentration ergaben jedoch eine Spezies mit geringeren Abklingzeiten als die Yb3+-dotierten Ceroxidproben nach der PARAFAC-Analyse. Durch die Kalzinierung der Nanokomposite bei zwei hohen Temperaturen wurde die Entwicklung der Emissionsmuster von spezifischen Eu3+-Gitterplätzen verfolgt, die auf strukturelle Veränderungen der Nanokomposite hinweisen. Die Ergebnisse der Spektroskopie ergänzten die mit den konventionellen Techniken gewonnenen Daten. Das Ausglühen der Proben bei 773 K führte zu amorphen, ungeordneten Domänen, während die totalen Lumineszenzpektren der Nanokomposite bei 1273 K zwei unterschiedliche Stellen erkennen lassen, wobei die meisten rotverschobenen Eu3+-Spezies von reinem Eu3+-dotiertem ZrO2 auf dem YSZ-Träger stammen. Schließlich wurde für Eu3+-dotiertes Ceroxid ein erfolgreicher Transfer von der hydrophoben in die Wasserphase und eine anschließende Biokompatibilität mit ssDNA erreicht. Die PARAFAC-Analyse für Eu3+ in Nanopartikeln, die in Toluol und Wasser dispergiert wurden, ergab eine Eu3+-Spezies mit leicht unterschiedlichen Oberflächeneigenschaften der Nanopartikel, was die Lumineszenzkinetik und die Lösungsmittelumgebung betraf. Mehrere funktionalisierte Nanopartikel, die nach der Hybridisierung auf Origami-Dreiecken konjugiert waren, wurden mit Hilfe der Rasterkraftmikroskopie (AFM) sichtbar gemacht. Die Eu3+- und Yb3+-Spektroskopie wurde eingesetzt, um die strukturellen Veränderungen zu überwachen und die Möglichkeit des Transfers der Nanopartikel in Wasser zu bestimmen. PARAFAC erweist sich als ein leistungsfähiges Instrument zur Analyse von Lanthanidenspektren in kristallinen Feststoffen und in Lösungen, die durch zahlreiche Stark-Übergänge gekennzeichnet sind und bei denen Messungen in der Regel eine Überlagerung verschiedener Emissionsbeiträge zu einem bestimmten Spektrum ergeben. KW - cerium oxide KW - europium KW - luminescence KW - PARAFAC KW - ytterbium KW - species KW - Ceroxid KW - Lumineszenz KW - Nanokomposite KW - Spezies Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-619443 ER - TY - THES A1 - Chen, Guoxiang T1 - Nanoparticles at solid interfaces N2 - Nanoparticles (NPs) are particles between 1 and 100 nanometers in size. They have attracted enormous research interests owing to their remarkable physicochemical properties and potential applications in the optics, catalysis, sensing, electronics, or optical devices. The thesis investigates systems of NPs attached to planar substrates. In the first part of the results section of the thesis a new method is presented to immobilize NPs. In many NP applications a strong, persistent adhesion to substrates is a key requirement. Up to now this has been achieved with various methods, which are not always the optimum regarding adhesion strength or applicability. We propose a new method which uses capillarity to enhance the binding agents in the contact area between NP and substrate. The adhesion strength resulting from the new approach is investigated in detail and it is shown that the new approach is superior to older methods in several ways. The following section presents the optical visualization of nano-sized objects through a combination of thin film surface distortion and interference enhanced optical reflection microscopy. It is a new, fast and non-destructive technique. It not only reveals the location of NPs as small as 20nm attached to planar surfaces and embedded in a molecularly thin liquid film. It also allows the measurement of the geometry of the surface distortion of the liquid film. Even for small NPs the meniscus reaches out for micrometers, which is the reason why the NPs produce such a pronounced optical footprint. The nucleation and growth of individual bubbles is presented in chapter 5. Nucleation is a ubiquitous natural phenomenon and of great importance in numerous industrial processes. Typically it occurs on very small scales (nanometers) and it is of a random nature (thermodynamics of small systems). Up to now most experimental nucleation studies deal with a large number of individual nucleation processes to cope with its inherently statistical, spatio-temporal character. In contrast, in this thesis the individual O2-bubble formation from single localized platinum NP active site is studied experimentally. The bubble formation is initiated by the catalytic reaction of H2O2 on the Pt surface. It is studied how the bubble nucleation and growth depends on the NP size, the H2O2 concentration and the substrate surface properties. It is observed that in some cases the bubbles move laterally over the substrate surface, driven by the O2-production and the film ablation. KW - Nanoparticles, Adhesion, Interfaces, Bubble, Imaging Y1 - 2018 ER - TY - THES A1 - Chen, Zupeng T1 - Novel strategies to improve (photo)catalytic performance of carbon nitride-based composites Y1 - 2015 ER - TY - THES A1 - Cheng, Xiao T1 - Controlled solvent vapor annealing of block copolymer films T1 - Kontrolliertes Lösungsmitteldampfglühen von Blockcopolymerfilmen N2 - This project was focused on exploring the phase behavior of poly(styrene)187000-block-poly(2-vinylpyridine)203000 (SV390) with high molecular weight (390 kg/mol) in thin films, in which the self-assembly of block copolymers (BCPs) was realized via thermo-solvent annealing. The advanced processing technique of solvent vapor treatment provides controlled and stable conditions. In Chapter 3, the factors to influence the annealing process and the swelling behavior of homopolymers are presented and discussed. The swelling behavior of BCP in films is controlled by the temperature of the vapor and of the substrate, on one hand, and variation of the saturation of the solvent vapor atmosphere (different solvents), on the other hand. Additional factors like the geometry and material of the chamber, the type of flow inside the chamber etc. also influence the reproducibility and stability of the processing. The slightly selective solvent vapor of chloroform gives 10% more swelling of P2VP than PS in films with thickness of ~40 nm. The tunable morphology in ultrathin films of high molecular weight BCP (SV390) was investigated in Chapter 4. First, the swelling behavior can be precisely tuned by temperature and/or vapor flow separately, which provided information for exploring the multiple-parameter-influenced segmental chain mobility of polymer films. The equilibrium state of SV390 in thin films influenced by temperature was realized at various temperatures with the same degree of swelling. Various methods including characterization with SFM, metallization and RIE were used to identify the morphology of films as porous half-layer with PS dots and P2VP matrix. The kinetic investigations demonstrate that on substrates with either weak or strong interaction the original morphology of the BCP with high molecular weight is changed very fast within 5 min, and the further annealing serves for annihilation of defects. The morphological development of symmetric BCP in films with thickness increasing from half-layer to one-layer influenced by confinement factors of gradient film thicknesses and various surface properties of substrates was studied in Chapter 5. SV390 and SV99 films show bulk lamella-forming morphology after slightly selective solvent vapor (chloroform) treatment. SV99 films show cylinder-forming morphology under strongly selective solvent vapor (toluene) treatment since the asymmetric structure (caused by toluene uptake in PS blocks only) of SV99 block copolymer during annealing. Both kinds of morphology (lamella and cylinder) are influenced by the film thickness. The annealed morphology of SV390 and SV99 influenced by the combination of confined film and substrate property is similar to the morphology on flat silicon wafers. In this chapter the gradients in the film thickness and surface properties of the substrates with regard to their influence on the morphological development in thin BCP films are presented. Directed self-assembly (graphoepitaxy) of this SV390 was also investigated to compare with systematically reported SV99. In Chapter 6 an approach to induced oriented microphase separation in thick block copolymer films via treatment with the oriented vapor flow using mini-extruder is envisaged to be an alternative to existing methodologies, e.g. via non-solvent-induced phase separation. The preliminary tests performed in this study confirm potential perspective of this method, which alters the structure through the bulk of the film (as revealed by SAXS measurements), but more detailed studies have to be conducted in order to optimize the preparation. N2 - Im Rahmen dieser Arbeit wurde das Phasenverhalten von Poly(styrol)_187000 -block-poly(2-Vinylpyridin)_203000 (SV^390 ) hohen Molekulargewichts (390 kg/mol) in dünnen Filmen untersucht, in denen die Selbstassemblierung der Block-Copolymere durch Lösungsmitteltempern erreicht wurde. Das hochentwickelte Verfahren der Behandlung mit Lösungsmitteldampf bietet kontrollierte und stabile Bedingungen. In *Kapitel 3* werden die Faktoren diskutiert, die den Prozess des Temperns und das Schwellverhalten der dünnen Block-Copolymer Filme beeinflussen. Das Schwellverhalten von Block-Copolymeren in Filmen wird einerseits durch die Temperaturen des Lösungsmitteldampfes und des Substrates sowie andererseits dem Sättigungs-Dampfdruck kontrolliert. Zusätzlich beeinflussen auch Faktoren wie die Geometrie und das Material der Kammer sowie die Art der Strömung in der Kammer die Reproduzierbarkeit und Stabilität der Messungen. Der geringfügig selektive Lösungsmitteldampf von Chloroform führt zu 10% stärkerem Schwellen des P2VP-Blocks im Vergleich zu PS in Filmen mit einer Dicke von ca. 40 nm. Die variable Morphologie ultradünner Filme eines Block-Copolymers hohen Molekulargewichts (SV^390 ) wurde in *Kapitel 4* untersucht. Das Schwellverhalten kann durch die Temperatur und den Dampffluss unabhängig voneinander präzise beeinflusst werden. Die Umgebungstemperatur stellt einen limitierenden Faktor für den Bereich der Annealing-Temperatur aufgrund der möglichen Kondensation des Lösungsmitteldampfes dar. Mehrere Methoden, wie zum Beispiel die Charakterisierung mit Rasterkraftmikroskopie, Metallisierung und reaktives Ionenätzen, wurden verwendet, um die Morphologie der Filme als perforierte Lamellen mit PS-Kugeln und P2VP-Matrix zu bestimmen. Eine Analyse der Kinetik der Strukturbildung zeigt, dass sich die ursprüngliche Morphologie von Block-Copolymeren hohen Molekulargewichts sowohl auf Substraten mit schwacher als auch starker Wechselwirkung innerhalb von 5 min ändert und das weitere Tempern zum Ausheilen von Defekten führt. Die morphologische Veränderung von symmetrischen Block-Copolymeren bei Filmdicken zwischen einer halben Domänendicke und einer ganzen Domänendicke wurde in *Kapitel 5* in Abhängigkeit von Gradienten der Filmdicke und verschiedenen Oberflächeneigenschaften der Substrate untersucht. SV^390 und SV^99 Filme zeigen eine lamellare Bulk-Morphologie nach Behandlung mit geringfügig selektivem Lösungsmitteldampf (Chloroform). SV^99 Filme bilden eine zylindrische Morphologie unter Behandlung mit stark selektivem Lösungsmitteldampf (Toluol) aus, weil das SV^99 Block-Copolymer während des Temperns eine asymmetrische Struktur aufweist (Toluol-Aufnahme ausschließlich im Polystyrol-Block). Beide Morphologien (Lamellen und Zylinder) werden durch die Filmdicke beeinflusst. Die Morphologie von SV^390 und SV^99 nach Tempern ist abhängig von der Filmdicke und den Substrat-Eigenschaften und ähnlich der Morphologie auf flachen Silicium-Wafern. In *Kapitel 6* wird ein Ansatz zur induzierten orientierten Mikrophasenseparation in dicken Block-Copolymer Filmen durch Behandlung mit orientiertem Dampffluss unter Verwendung eines Miniextruders vorgestellt, der als Alternative zu existierenden Verfahren wie Nichtlösungsmittel-induzierter Phasenseparation dienen könnte. Die ersten im Rahmen dieser Arbeit durchgeführten Untersuchungen zeigen das Potential der Methode auf, welche die Struktur im gesamten Volumen des Films durchgehend beeinflusst (durch SAXS-Messungen gezeigt). Jedoch sind detailliertere Studien notwendig, um die Prozedur zu optimieren. KW - block copolymer KW - thin films KW - solvo-thermal annealing KW - Block-copolymer KW - dünne Filme KW - Lösungsmittel-thermisches Tempern Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-424179 ER - TY - THES A1 - Choi, Youngeun T1 - DNA origami structures as versatile platforms for nanophotonics T1 - DNA Origami Struktruen als Vielseitige Plattform für Nanophotonik N2 - Nanophotonics is the field of science and engineering aimed at studying the light-matter interactions on the nanoscale. One of the key aspects in studying such optics at the nanoscale is the ability to assemble the material components in a spatially controlled manner. In this work, DNA origami nanostructures were used to self-assemble dye molecules and DNA coated plasmonic nanoparticles. Optical properties of dye nanoarrays, where the dyes were arranged at distances where they can interact by Förster resonance energy transfer (FRET), were systematically studied according to the size and arrangement of the dyes using fluorescein (FAM) as the donor and cyanine 3 (Cy 3) as the acceptor. The optimized design, based on steady-state and time-resolved fluorometry, was utilized in developing a ratiometric pH sensor with pH-inert coumarin 343 (C343) as the donor and pH-sensitive FAM as the acceptor. This design was further applied in developing a ratiometric toxin sensor, where the donor C343 is unresponsive and FAM is responsive to thioacetamide (TAA) which is a well-known hepatotoxin. The results indicate that the sensitivity of the ratiometric sensor can be improved by simply arranging the dyes into a well-defined array. The ability to assemble multiple fluorophores without dye-dye aggregation also provides a strategy to amplify the signal measured from a fluorescent reporter, and was utilized here to develop a reporter for sensing oligonucleotides. By incorporating target capturing sequences and multiple fluorophores (ATTO 647N dye molecules), a reporter for microbead-based assay for non-amplified target oligonucleotide sensing was developed. Analysis of the assay using VideoScan, a fluorescence microscope-based technology capable of conducting multiplex analysis, showed the DNA origami nanostructure based reporter to have a lower limit of detection than a single stranded DNA reporter. Lastly, plasmonic nanostructures were assembled on DNA origami nanostructures as substrates to study interesting optical behaviors of molecules in the near-field. Specifically, DNA coated gold nanoparticles, silver nanoparticles, and gold nanorods, were placed on the DNA origami nanostructure aiming to study surface-enhanced fluorescence (SEF) and surface-enhanced Raman scattering (SERS) of molecules placed in the hotspot of coupled plasmonic structures. N2 - Nanophotonik bezeichnet die Untersuchung von Licht in Wechselwirkung mit Materie im Nanometermaßstab. Die exakte Kontrolle über den Aufbau und die räumliche Anordnung der beteiligten Komponenten ist ein entscheidender Faktor für die Erforschung der Optik nanoskalierter Systeme. Eine mögliche Lösung bietet die selbstorganisatorische Eigenschaft von DNA-Origami-Nanostrukturen, die im Rahmen dieser Dissertation, insbesondere zur Kopplung verschiedener Farbstoffe bzw. plasmonisch aktiver Nanopartikel, verwendet wurden. Im ersten Teil dieser Dissertation wurden unterschiedliche Förster-Resonanzenergietransfer- (FRET) Farbstoff-Matrizen, bestehend aus Fluorescein (FAM) als FRET-Donor und Cyanine 3 (Cy 3) als FRET-Akzeptor, hergestellt und nachfolgend hinsichtlich des Einflusses ihrer Gesamtgröße und ihrer Anordnung via statischer und zeitaufgelöster Fluoreszenzspektroskopie untersucht. Daraufhin erfolgte die Weiterentwicklung der ermittelten optimalen Anordnung der Farbstoffe in einen ratiometrischen pH-Sensor, bestehend aus dem pH stabilen Coumarin 343 (C343) als FRET-Donor und dem pH sensitiven FAM als FRET-Akzeptor. Die erhaltenen Ergebnisse zeigten, dass sich die Sensitivität ratiometrischer Sensoren, insbesondere durch die wohldefinierte Anordnung der beteiligten Farbstoffe in der Matrize, deutlich steigern lassen. Selbige Anordnung konnte auch erfolgreich zur Entwicklung eines Giftstoffsensors, zum Nachweis des Hepatoxins Thioacetamid (TAA), verwendet werden. Die Möglichkeit der Anordnung mehrerer Farbstoffe, unter Vermeidung ungewollter Farbstoff-Aggregation, ermöglicht außerdem die Verstärkung der Signale sogenannter Fluoreszenzreporter. Dies führte, im Rahmen dieser Arbeit, zur erfolgreichen Entwicklung eines auf Mikroperlen basierenden Oligonukleotid-Sensors, welcher ohne die Notwendigkeit einer vorherigen Zielverstärkung (z.B. durch Polymerase-Kettenreaktion) auskommt. Die anschließende Analyse mittels VideoScan, einer Multiplex-Analyse-Technik basierend auf der Fluoreszenzmikroskopie, ergab deutlich niedrigere Nachweisgrenzen für auf DNA-Origami basierende Reporter im Vergleich zu DNA-Einzelstrang basierenden Reportern. Abschließend erfolgte die Verwendung der DNA-Origamis als Substrat für die präzise räumliche Anordnung verschiedener plasmonisch aktiver Nanopartikel zur Untersuchung des optischen Verhaltens von Zielmolekülen im plasmonischen Nahfeld. Die Untersuchung der oberflächenverstärkten Fluoreszenz (SEF) und oberflächenverstärkten Raman-Streuung (SERS) von Molekülen im plasmonischer Hotspots erfolgte insbesondere mit Fokus auf den Einfluss der unterschiedlichen Anordnung von Gold-Nanostäbchen, Gold-Nanopartikel, und Silber-Nanopartikel. KW - DNA origami KW - Förster resonance energy transfer KW - plasmonics KW - DNA Origami KW - Förster-Resonanzenergietransfer KW - Plasmonik Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-421483 ER - TY - THES A1 - Chung, Kang Ko T1 - Heteroatom-containing carbons for high energy density supercapacitor T1 - Heteroatomhaltige Kohlenstoffe für Superkondensatoren mit hohen Energiedichten N2 - The supercapacitor is one of the most important energy storage devices as its construction allows for addressing many of the drawbacks related to batteries, but the low energy density of current systems is a major issue. In this doctoral dissertation, with a view to attaining high energy density supercapacitor systems that can be comparable to those for batteries, new heteroatom-containing carbons in the form of particles and three-dimensional films were investigated. A nitrogen-containing material, acrodam, was chosen as the carbon precursor due to the inexpensiveness, high carbonization yield, oligomerizability, etc. The carbon particles were prepared from acrodam together with caesium acetate as a meltable flux agent, and disclosed excellent properties in hydroquinone-loaded sulphuric acid electrolyte with high energy densities (up to 133.0 Wh kg–1) and sufficient cycle stabilities. These properties are already now comparable to those of batteries. Besides, conductive carbon three-dimensional films were fabricated using acrodam oligomer as the precursor by the inexpensive spin coating method. The films were found to be homogeneous, flat, void- and crack-free, and high conductivities (up to 334 S cm–1) could be obtained at the carbonization temperature of 1000 ºC. Furthermore, a porous carbon three-dimensional film could be formed using an organic template at the first attempt. This finding demonstrates the film’s potentiality for various applications such as supercapacitor electrode; the essential absence of contact resistance within the network should contribute to effective transportation of electron within the electrode. The progress made in this dissertation will open a new way to further enhancement of energy density for supercapacitor as well as other applications that exceeds the current properties. N2 - Der Superkondensator ist einer der wichtigsten Energiespeicher da seine Konstruktion die Lösung vieler Nachteile von Batterien erlaubt. Allerdings weisen derzeitige Systeme noch zu geringe Energiedichten auf. Um Superkondensatoren mit Energiedichten vergleichbar zu Batterien zu ermöglichen, wurden in der vorliegenden Dissertation neue, heteroatomhaltige Kohlenstoffe in Form von Partikeln und Filmen untersucht. Aufgrund geringer Kosten, hohen Ausbeuten, Polymerisierbarkeit usw. wurde die stickstoffhaltige Substanz Acrodam als Kohlenstoffvorstufe verwendet. Die Kohlenstoffpartikel wurden ausgehend von Acrodam zusammen mit Cäsiumacetat als schmelzbares Flussmittel hergestellt und wiesen ausgezeichnete Eigenschaften in Hydrochinon geladenen Schwefelsäure-Elektrolyten mit hohen Energiedichten (bis zu 133,0 Wh kg–1) und guten Zyklusstabilitäten auf. Diese Eigenschaften sind bereits jetzt vergleichbar mit denen von Batterien. Weiterhin wurden unter Verwendung von Acrodamoligomeren als Vorstufe und mit Hilfe der kostengünstigen Rotationsbeschichtung leitfähige, dreidimensionale Kohlenstofffilme hergestellt. Bei einer Karbonisierungstemperatur von 1000 °C konnten die Materialien als homogene, flache, Hohlraum-und Riss-freie Filme erhalten werden, die eine hohe Leitfähigkeit (bis zu 334 S cm–1) aufwiesen. Darüber hinaus konnte mit einem organischen Templat ein dreidimensionaler, poröser Kohlenstoff geformt werden. Dies zeigt das Potential der Filme für verschiedene Anwendungen wie Superkondensatorelektroden; die Abwesenheit von Übergangswiderständen im Netzwerk sollte zu einem effizienten Transport von Elektronen in der Elektrode beitragen. Die Ergebnisse dieser Dissertation werden neue Wege zur Verbesserung der Energiedichte von Superkondensatoren sowie weiteren Anwendungen eröffnen. KW - supercapacitor KW - carbon KW - heteroatom KW - energy density Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-69826 ER -