TY - THES A1 - Zühlke, Martin T1 - Elektrosprayionisation Ionenmobilitätsspektrometrie T1 - Electrospray ionization Ion mobility spectrometry BT - Entwicklung, Charakterisierung und Anwendung zur HPLC-Detektion und zum Reaktionsmonitoring BT - development, characterization and application for HPLC detection and reaction monitoring N2 - Die Elektrosprayionisation (ESI) ist eine der weitverbreitetsten Ionisationstechniken für flüssige Pro-ben in der Massen- und Ionenmobilitäts(IM)-Spektrometrie. Aufgrund ihrer schonenden Ionisierung wird ESI vorwiegend für empfindliche, komplexe Moleküle in der Biologie und Medizin eingesetzt. Überdies ist sie allerdings für ein sehr breites Spektrum an Substanzklassen anwendbar. Die IM-Spektrometrie wurde ursprünglich zur Detektion gasförmiger Proben entwickelt, die hauptsächlich durch radioaktive Quellen ionisiert werden. Sie ist die einzige analytische Methode, bei der Isomere in Echtzeit getrennt und über ihre charakteristische IM direkt identifiziert werden können. ESI wurde in den 90ger Jahren durch die Hill Gruppe in die IM-Spektrometrie eingeführt. Die Kombination wird bisher jedoch nur von wenigen Gruppen verwendet und hat deshalb noch ein hohes Entwick-lungspotential. Ein vielversprechendes Anwendungsfeld ist der Einsatz in der Hochleistungs-flüssigkeitschromatographie (HPLC) zur mehrdimensionalen Trennung. Heutzutage ist die HPLC die Standardmethode zur Trennung komplexer Proben in der Routineanalytik. HPLC-Trennungsgänge sind jedoch häufig langwierig und der Einsatz verschiedener Laufmittel, hoher Flussraten, von Puffern, sowie Laufmittelgradienten stellt hohe Anforderungen an die Detektoren. Die ESI-IM-Spektrometrie wurde in einigen Studien bereits als HPLC-Detektor eingesetzt, war dort bisher jedoch auf Flussratensplitting oder geringe Flussraten des Laufmittels beschränkt. In dieser kumulativen Doktorarbeit konnte daher erstmals ein ESI IM-Spektrometer als HPLC-Detektor für den Flussratenbereich von 200-1500 μl/min entwickelt werden. Anhand von fünf Publi-kationen wurden (1) über eine umfassende Charakterisierung die Eignung des Spektrometers als HPLC-Detektor festgestellt, (2) ausgewählte komplexe Trenngänge präsentiert und (3) die Anwen-dung zum Reaktionsmonitoring und (4, 5) mögliche Weiterentwicklungen gezeigt. Erfolgreich konnten mit dem selbst-entwickelten ESI IM-Spektrometer typische HPLC-Bedingungen wie Wassergehalte im Laufmittel von bis zu 90%, Pufferkonzentrationen von bis zu 10 mM, sowie Nachweisgrenzen von bis zu 50 nM erreicht werden. Weiterhin wurde anhand der komplexen Trennungsgänge (24 Pestizide/18 Aminosäuren) gezeigt, dass die HPLC und die IM-Spektrometrie eine hohe Orthogonalität besitzen. Eine effektive Peakkapazität von 240 wurde so realisiert. Auf der HPLC-Säule koeluierende Substanzen konnten über die Driftzeit getrennt und über ihre IM identifi-ziert werden, sodass die Gesamttrennzeiten erheblich minimiert werden konnten. Die Anwend-barkeit des ESI IM-Spektrometers zur Überwachung chemischer Synthesen wurde anhand einer dreistufigen Reaktion demonstriert. Es konnten die wichtigsten Edukte, Zwischenprodukte und Produkte aller Stufen identifiziert werden. Eine quantitative Auswertung war sowohl über eine kurze HPLC-Vortrennung als auch durch die Entwicklung eines eigenen Kalibrierverfahrens, welches die Ladungskonkurrenz bei ESI berücksichtigt, ohne HPLC möglich. Im zweiten Teil der Arbeit werden zwei Weiterentwicklungen des Spektrometers präsentiert. Eine Möglichkeit ist die Reduzierung des Drucks in den intermediären Bereich (300 - 1000 mbar) mit dem Ziel der Verringerung der benötigten Spannungen. Mithilfe von Streulichtbildern und Strom-Spannungs-Kurven wurden für geringe Drücke eine verminderte Freisetzung der Analyt-Ionen aus den Tropfen festgestellt. Die Verluste konnten jedoch über höhere elektrische Feldstärken ausgeglichen werden, sodass gleiche Nachweisgrenzen bei 500 mbar und bei 1 bar erreicht wurden. Die zweite Weiterentwicklung ist ein neuartiges Ionentors mit Pulsschaltung, welches eine Verdopplung der Auflösung auf bis zu R > 100 bei gleicher Sensitivität ermöglichte. Eine denkbare Anwendung im Bereich der Peptidanalytik wurde mit beachtlichen Auflösungen der Peptide von R = 90 gezeigt. N2 - Electrospray ionization (ESI) is one of the most widespread ionization techniques for liquid samples in mass and ion mobility (IM) spectrometry. Due to its gentle ionization, ESI is often used for sensitive, complex molecules in biology and medicine. However, it is also applicable to a wide range of substance classes. IM spectrometry was originally developed for the detection of gaseous samples, which are mainly ionized by radioactive sources. It is the only analytical method in which isomers can be separated in real time and directly identified by their characteristic IM. ESI was introduced to IM spectrometry by the Hill Group in the 90s. So far, the combination was only used by a limited number of groups and therefore there is still a large development potential. A highly promising field of application is highperformance liquid chromatography (HPLC) for multidimensional separations. At present, HPLC is the standard method for the separation of complex samples in routine analysis. However, HPLC separations are often time-consuming and the use of different solvents, high flow rates, buffers, as well as solvent gradients impose high demands on the detectors. ESI IM spectrometry was already used as an HPLC detector in a number of studies. However, these studies were restricted to splitting or low flow rates of the mobile phase. In this cumulative thesis, an ESI IM spectrometer was developed as an HPLC detector for the flow rate range of 200-1500 μl/min for the first time. Based on five publications, (1) the suitability of the spectrometer as an HPLC detector was comprehensively characterized, (2) selected complex separations are presented, and (3) the application to the reaction monitoring as well as (4, 5) possible further developments are shown. With the in-house developed ESI IM spectrometer, typical HPLC conditions such as water contents in the mobile phase of up to 90%, buffer concentrations of up to 10 mM, as well as detection limits of up to 50 nM, were achieved successfully. Furthermore, on the basis of a complex separation (24 pesticides/18 amino acids), it could be demonstrated that HPLC and IM spectrometry possess a high degree of orthogonality. An effective peak capacity of 240 was thus realized. Substances coeulating on the HPLC column could be separated in the drift time and were identified by their IM. Thus, the overall separation times could be significantly reduced. The applicability of the ESI IM spectrometer for the monitoring of chemical syntheses was demonstrated for a three-stage reaction. The main starting materials, intermediates and products of all stages could be identified. A quantitative evaluation was possible both by means of a short HPLC pre-separation as well as by a newly developed calibration procedure, which takes charge competition during ESI into account, without HPLC. In the second part of the thesis, two further developments of the spectrometer are presented. One possibility is a reduction of the pressure to the intermediate range (300 - 1000 mbar) with the aim of reducing the required voltages. With the help of scattered light images and current-voltage curves, a reduced release of analyte ions from the droplets was determined at low pressures. However, these losses could be compensated for by higher electric field strengths. Therefore, the same detection limits were achieved at 500 mbar and at 1 bar. The second development is a novel ion gate with pulse switching, which allows a doubling of the resolution up to R > 100 with equal sensitivity. A possible application in the field of peptide analysis was demonstrated, achieving a considerable resolutions of R = 90 for the peptides. KW - HPLC KW - HPLC KW - Ionenmobilitätsspektrometrie KW - Elektrosprayionisation KW - ion mobility spectrometry KW - electrospray ionization (ESI) Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-407452 ER - TY - THES A1 - Zintchenko, Arkadi T1 - Polyelektrolythkomplexbildung mit doppelhydrophilen Blockcopolymeren Y1 - 2002 ER - TY - THES A1 - Zimmermann, Marc T1 - Multifunctional patchy silica particles via microcontact printing T1 - Multifunktionale Patchy Silika Partikel mithilfe des Mikrokontaktdruckverfahrens N2 - This research addressed the question, if it is possible to simplify current microcontact printing systems for the production of anisotropic building blocks or patchy particles, by using common chemicals while still maintaining reproducibility, high precision and tunability of the Janus-balance Chapter 2 introduced the microcontact printing materials as well as their defined electrostatic interactions. In particular polydimethylsiloxane stamps, silica particles and high molecular weight polyethylenimine ink were mainly used in this research. All of these components are commercially available in large quantities and affordable, which gives this approach a huge potential for further up-scaling developments. The benefits of polymeric over molecular inks was described including its flexible influence on the printing pressure. With this alteration of the µCP concept, a new method of solvent assisted particle release mechanism enabled the switch from two-dimensional surface modification to three-dimensional structure printing on colloidal silica particles, without changing printing parameters or starting materials. This effect opened the way to use the internal volume of the achieved patches for incorporation of nano additives, introducing additional physical properties into the patches without alteration of the surface chemistry. The success of this system and its achievable range was further investigated in chapter 3 by giving detailed information about patch geometry parameters including diameter, thickness and yield. For this purpose, silica particles in a size range between 1µm and 5µm were printed with different ink concentrations to change the Janus-balance of these single patched particles. A necessary intermediate step, consisting of air-plasma treatment, for the production of trivalent particles using "sandwich" printing was discovered and comparative studies concerning the patch geometry of single and double patched particles were conducted. Additionally, the usage of structured PDMS stamps during printing was described. These results demonstrate the excellent precision of this approach and opens the pathway for even greater accuracy as further parameters can be finely tuned and investigated, e.g. humidity and temperature during stamp loading. The performance of these synthesized anisotropic colloids was further investigated in chapter 4, starting with behaviour studies in alcoholic and aqueous dispersions. Here, the stability of the applied patches was studied in a broad pH range, discovering a release mechanism by disabling the electrostatic bonding between particle surface and polyelectrolyte ink. Furthermore, the absence of strong attractive forces between divalent particles in water was investigated using XPS measurements. These results lead to the conclusion that the transfer of small PDMS oligomers onto the patch surface is shielding charges, preventing colloidal agglomeration. However, based on this knowledge, further patch modifications for particle self-assembly were introduced including physical approaches using magnetic nano additives, chemical patch functionalization with avidin-biotin or the light responsive cyclodextrin-arylazopyrazoles coupling as well as particle surface modification for the synthesis of highly amphiphilic colloids. The successful coupling, its efficiency, stability and behaviour in different solvents were evaluated to find a suitable coupling system for future assembly experiments. Based on these results the possibility of more sophisticated structures by colloidal self-assembly is given. Certain findings needed further analysis to understand their underlying mechanics, including the relatively broad patch diameter distribution and the decreasing patch thickness for smaller silica particles. Mathematical assumptions for both effects are introduced in chapter 5. First, they demonstrate the connection between the naturally occurring particle size distribution and the broadening of the patch diameter, indicating an even higher precision for this µCP approach. Second, explaining the increase of contact area between particle and ink surface due to higher particle packaging, leading to a decrease in printing pressure for smaller particles. These calculations ultimately lead to the development of a new mechanical microcontact printing approach, using centrifugal forces for high pressure control and excellent parallel alignment of printing substrates. First results with this device and the comparison with previously conducted by-hand experiments conclude this research. It furthermore displays the advantages of such a device for future applications using a mechanical printing approach, especially for accessing even smaller nano particles with great precision and excellent yield. In conclusion, this work demonstrates the successful adjustment of the µCP approach using commercially available and affordable silica particles and polyelectrolytes for high flexibility, reduced costs and higher scale-up value. Furthermore, its was possible to increase the modification potential by introducing three-dimensional patches for additional functionalization volume. While keeping a high colloidal stability, different coupling systems showed the self-assembly capabilities of this toolbox for anisotropic particles. N2 - Diese Forschungsarbeit befasste sich mit der Frage, ob es möglich ist, bekannte Mikrokontaktdruckverfahren, zur Herstellung von anisotropen Bausteinen (Patchy Partikel), weiter zu vereinfachen. Dabei sollten gängige Chemikalien verwendet werden ohne einen Verlust in Reproduzierbarkeit, hoher Präzision und Feineinstellung der Janus-Balance zu erleiden. In Kapitel 2 wurden die verwendeten Mikrokontaktdruckmaterialien sowie deren elektrostatische Wechselwirkungen vorgestellt. Insbesondere handelte es sich dabei um Polydimethylsiloxan Stempel, Silikapartikel und hoch molekulare Polyethylenimin Tinte. All diese Produkte sind kommerziel in großen und bezahlbaren Mengen erhältlich. Nicht nur die Vorteile von polymeren Tinten im Gegensatz zu molekularen Tinten wurde beschrieben, sondern auch die hohe Flexibilität dieses Verfahrens bezüglich der verwendeten Druckkraft. Mit dieser Anpassung des Mikrokontaktdrucks, wurde eine neue Methode der Lösungsmittel unterstützten Partikelablösung ermöglicht, mit deren Hilfe ein einfaches Schalten zwischen zwei dimensionaler Oberflächenfunktionalisierung und drei dimensionalem Strukturdrucks möglich war, ohne Druckparameter oder Startchemikalien zu verändern. Dadurch konnte neu erschaffenes internes Volumen verwendet werden um Nanoadditive einzuführen und so zusätzliche physikalische Eigenschaften zu integrieren, ohne die Oberflächenchemie der Patches verändert wurde. Der Erfolg dieses Systems und seine erreichbaren Grenzen wurde gründlichst in Kapitel 3 erforscht, indem detaillierte Geometrieparameter der Patches einschließlich Durchmesser, Dicke und Ausbeute, erworben wurden. Hierfür wurden Silikapartikel in einem Größenbereich von 1µm bis 5µm mit unterschiedlichen Tintenkonzentrationen bedruckt, um Veränderungen erforschen zu können. Ein notwendiger Luftplasma Ätzschritt für die Produktion von trivalenten Partikeln, mit Hilfe des sogenannten ,,Sandwich‘‘-Drucks, wurde erläutert und vergleichende Untersuchen von einfach und zweifach modifizierten Bausteinen wurden durchgeführt. Zusätzlich dazu, wurde die Verwendung von strukturierten Stempel beschrieben. Die Ergebnisse verdeutlichen die exzellente Genauigkeit dieser Methode und öffnet den Weg um eine hoch höhere Präzision zu erreichen da weitere Parametere genau eingestellt und untersucht werden können, z.B. Luftfeuchtigkeit und Temperature während der Stempelbeladung. Die Performance der herstellten anisotropen Partikel wurde in Kapitel 4 mit Verhaltensstudien in alkoholischen und wässrigen Dispersionen getestet. Dabei wurde die Stabilität der Oberflächenfunktionalisierungen in einem breiten pH Bereich untersucht. Dadurch wurde ein Ablösungsmechanismus bei sehr hohen bzw. niedrigen pH-Werten entdeckt, der zur Deaktivierung elektrostatischer Wechselwirkungen zwischen Partikeloberfläche und Polyelektrolyte Tinte führte. Desweitern wurden die Abwesenheit starker Wechselwirkung der divalenten Partikel in Wasser mit Hilfe von XPS untersucht. Das Resultat zeigte, dass der Transfer kleinster PDMS Oligomere auf die Patchoberfläche zu einer Ladungsabschirmung führte. Dadurch konnte Agglomeration verhindert werden. Aufgrund dieser Ergebnisse wurden weitere Modifikationen für Partikelassemblierung durchgeführt. Hierfür wurde die Einführung von magnetischen Nanoadditiven, die Funktionalisierung mit Avidin-Biotin sowie dem Lichtschaltbaren Cyclodextrin-Arylazopyrazol Komplexen und die Partikeloberflächenfunktionalisierung zur Herstellung amphiphiler Teilchen untersucht. Die Effizienz der Kopplung, deren Stabilität sowie das Verhalten in unterschiedlichen Lösungsmittel wurde beschrieben. Basierend auf diesen Ergebnissen können noch anspruchsvollere Strukturen durch kolloidale Selbstassemblierung erzeugt werden. Einige Ergebnisse dieser Arbeit benötigten zusätzlicher Analyse um die zugrundeliegenden Mechaniken verstehen zu können. Dazu gehörte die relative hohe Streuung des Durchmessers für unterschiedliche Partikelsysteme, sowie das Ausdünnen des Patches mit kleineren Silikapartikeln. Mathematische Modelle in Kapitel 5 beschreiben beide Effekte. Dadurch war es möglich einen Zusammenhang zwischen der natürlichen Partikelgrößenverteilung sowie der Verbreitung des Patchdurchmessers festzustellen. Des Weiteren konnte eine Verkleinerung der Druckkraft durch eine Erhöhung der Packungsdichte für kleine Partikel beschrieben werden, wodurch eine Erklärung der Ausdünnung möglich war. All diese Berechnung führten schlussendlich zur Entwicklung eines neuen mechanischen Mikrokontaktdruckverfahrens, welches mit Hilfe von Zentrifugalkräften eine hohe Druckkontrolle und eine exzellente parallele Ausrichtung zwischen den Substraten ermöglicht. Erste Ergebnisse, sowie deren Vergleich mit bisher erhaltenen Resultaten schließen diese Forschung ab. Des Weiteren zeigt es die Vorteile einer solchen Vorrichtung für kommende Applikationen, besonders um noch kleinere Nanopartikel mit einer hohen Präzision modifizieren zu können. Zusammenfassend ist zu sagen, dass diese Forschung die erfolgreiche Anpassung des Mikrokontaktdruckverfahrens mit kommerziell erhältlichen und bezahlbaren Silikapartikeln und Polyelektrolyten demonstriert, um hohe Flexibilität, reduzierte Kosten und ein erweitertes Skalierungspotential zu bieten. Zusätzlich ist es gelungen, die Funktionalisierungsdichte zu erhöhen, indem drei dimensionaler Strukturdruck bisher ungenutztes Volumen schaffen konnte. Während eine hohe kolloidale Stabilität erhalten blieb, ist es gelungen unterschiedliche Kopplungssysteme zu nutzen, um das Selbstorganisationspotential dieser Toolbox für anisotrope Partikel aufzuzeigen. KW - patchy particles KW - microcontact printing KW - silica particles KW - anisotropic colloids KW - polyelectrolytes KW - Patchy Partikel KW - Mikrokontaktdruck KW - Silika Partikel KW - Anisotrope Kolloide KW - Polyelektrolyte Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-427731 ER - TY - THES A1 - Zimmermann, Diana T1 - Direkte Arylierung BT - eine alternative Synthesemethode zur Herstellung von Absorberpolymeren für die organische Photovoltaik Y1 - 2018 ER - TY - THES A1 - Zhou, Shuo T1 - Biological evaluation and sulfation of polymer networks from glycerol glycidyl ether N2 - Cardiovascular diseases are the main cause of death worldwide, and their prevalence is expected to rise in the coming years. Polymer-based artificial replacements have been widely used for the treatment of cardiovascular diseases. Coagulation and thrombus formation on the interfaces between the materials and the human physiological environment are key issues leading to the failure of the medical device in clinical implantation. The surface properties of the materials have a strong influence on the protein adsorption and can direct the blood cell adhesion behavior on the interfaces. Furthermore, implant-associated infections will be induced by bacterial adhesion and subsequent biofilm formation at the implantation site. Thus, it is important to improve the hemocompatibility of an implant by altering the surface properties. One of the effective strategies is surface passivation to achieve protein/cell repelling ability to reduce the risk of thrombosis. This thesis consists of synthesis, functionalization, sterilization, and biological evaluation of bulk poly(glycerol glycidyl ether) (polyGGE), which is a highly crosslinked polyether-based polymer synthesized by cationic ring-opening polymerization. PolyGGE is hypothesized to be able to resist plasma protein adsorption and bacterial adhesion due to analogous chemical structure as polyethylene glycol and hyperbranched polyglycerol. Hydroxyl end groups of polyGGE provide possibilities to be functionalized with sulfates to mimic the anti-thrombogenic function of the endothelial glycocalyx. PolyGGE was synthesized by polymerization of the commercially available monomer glycerol glycidyl ether, which was characterized as a mixture of mono-, di- and tri-glycidyl ether. Cationic ring opening-polymerization of this monomer was carried out by ultraviolet (UV) initiation of the photo-initiator diphenyliodonium hexafluorophosphate. With the increased UV curing time, more epoxides in the side chains of the monomers participated in chemical crosslinking, resulting in an increase of Young’s modulus, while the value of elongation at break of polyGGE first increased due to the propagation of the polymer chains then decreased with the increase of crosslinking density. Eventually, the chain propagation can be effectively terminated by potassium hydroxide aqueous solution. PolyGGE exhibited different tensile properties in hydrated conditions at body temperature compared to the values in the dry state at room temperature. Both Young’s modulus and values of elongation at break were remarkably reduced when tested in water at 37 °C, which was above the glass transition temperature of polyGGE. At physiological conditions, entanglements of the ployGGE networks unfolded and the free volume of networks were replaced by water molecules as softener, which increased the mobility of the polymer chains, resulting in a lower Young’s modulus. Protein adsorption analysis was performed on polyGGE films with 30 min UV curing using an enzyme-linked immunosorbent assay. PolyGGE could effectively prevent the adsorption of human plasma fibrinogen, albumin, and fibronectin at the interface of human plasma and polyGGE films. The protein resistance of polyGGE was comparable to the negative controls: the hemocompatible polydimethylsiloxane (PDMS), showing its potential as a coating material for cardiovascular implants. Moreover, antimicrobial tests of bacterial activity using isothermal microcalorimetry and the microscopic image of direct bacteria culturing demonstrated that polyGGE could directly interfere biofilm formation and growth of both Gram-negative and antibiotic-resistant Gram-positive bacteria, indicating the potential application of polyGGE for combating the risk of hospital-acquired infections and preventing drug-resistant superbug spreading. To investigate its cell compatibility, polyGGE films were extracted by different solvents (ethanol, chloroform, acetone) and cell culture medium. Indirect cytotoxicity tests showed extracted polyGGE films still had toxic effects on L929 fibroblast cells. High-performance liquid chromatography/electrospray ionization mass spectrometry revealed the occurrence of organochlorine-containing compounds released during the polymer-cell culture medium interaction. A constant level of those organochlorine-containing compounds was confirmed from GGE monomer by a specific peak of C-Cl stretching in infrared spectra of GGE. This is assumed to be the main reason causing the increased cell membrane permeability and decreased metabolic activity, leading to cell death. Attempts as changing solvents were made to remove toxic substances, however, the release of these small molecules seems to be sluggish. The densely crosslinked polyGGE networks can possibly contribute to the trapping of organochlorine-containing compounds. These results provide valuable information for exploring the potentially toxic substances, leaching from polyGGE networks, and propose a feasible strategy for minimizing the cytotoxicity via reducing their crosslinking density. Sulfamic acid/ N-Methyl-2-pyrrolidone (NMP) were selected as the reagents for the sulfation of polyGGE surfaces. Fourier transform attenuated total reflection infrared spectroscopy (ATR-FT-IR) was used to monitor the functionalization kinetics and the results confirmed the successful sulfate grafting on the surface of polyGGE with the covalent bond -C-O-S-. X-ray photoelectron spectroscopy was used to determine the element composition on the surface and the cross-section of the functionalized polyGGE and sulfation within 15 min guarantees the sulfation only takes place on the surface while not occurring in the bulk of the polymer. The concentration of grafted sulfates increased with the increasing reaction time. The hydrophilicity of the surface of polyGGE was highly increased due to the increase of negatively charged end groups. Three sterilization techniques including autoclaving, gamma irradiation, and ethylene oxide (EtO) sterilization were used for polyGGE sulfates. Results from ATR-FT-IR and Toluidine Blue O quantitative assay demonstrated the total loss of the sulfates after autoclave sterilization, which was also confirmed by the increased water contact angle. Little influence on the concentration of sulfates was found for gamma-irradiated and autoclaving sterilized polyGGE sulfates. To investigate the thermal influence on polyGGE sulfates, one strategy was to use poly(hydroxyethyl acrylate) sulfates (PHEAS) for modeling. The thermogravimetric analysis profile of PHEAS demonstrated that sulfates are not thermally stable independent of the substrate materials and decomposition of sulfates occurs at around 100 °C. Although gamma irradiation also showed little negative effect on the sulfate content, the color change in the polyGGE sulfates indicates chemical or physical change might occur in the polymer. EtO sterilization was validated as the most suitable sterilization technique to maintain the chemical structure of polyGGE sulfates. In conclusion, the conducted work proved that bulk polyGGE can be used as an antifouling coating material and shows its antimicrobial potential. Sulfates functionalization can be effectively realized using sulfamic acid/NMP. EtO sterilization is the most suitable sterilization technique for grafted sulfates. Besides, this thesis also offers a good strategy for the analysis of toxic leachable substances using suitable physicochemical characterization techniques. Future work will focus on minimizing/eliminating the release of toxic substances via reducing the crosslinking density. Another interesting aspect is to study whether grafted sulfates can meet the need for anti-thrombogenicity. N2 - Herz-Kreislauf-Erkrankungen sind weltweit die Haupttodesursache, und es wird erwartet, dass ihre Prävalenz in den kommenden Jahren zunehmen wird. Künstlicher Ersatz auf Polymerbasis wird in großem Umfang für die Behandlung von Herz-Kreislauf-Erkrankungen eingesetzt. Gerinnung und Thrombenbildung an den Grenzflächen zwischen den Materialien und der menschlichen physiologischen Umgebung sind ein Hauptproblem, das zum Versagen des Medizinprodukts bei der klinischen Implantation führt. Die Oberflächeneigenschaften der Materialien haben einen starken Einfluss auf die Proteinadsorption und können das Adhäsionsverhalten von Blutzellen an den Grenzflächen steuern. Darüber hinaus werden Implantat-assoziierte Infektionen durch bakterielle Adhäsion und anschließende Biofilmbildung an der Implantationsstelle ausgelöst. Daher ist es wichtig, die Hämokompatibilität eines Implantats durch Veränderung der Oberflächeneigenschaften zu verbessern. Eine der wirksamen Strategien ist die Oberflächenpassivierung, um die Fähigkeit zur Protein-/Zellabweisung zu erreichen und so das Thromboserisiko zu verringern. Diese Arbeit befasst sich mit der Synthese, Funktionalisierung, Sterilisation und biologischen Bewertung von Poly(glycerin glycidyl ether) (polyGGE), einem stark vernetzten Polymer auf Polyetherbasis, das durch kationische Ringöffnungspolymerisation hergestellt wird. Es wird angenommen, dass PolyGGE aufgrund seiner ähnlichen chemischen Struktur wie Polyethylenglykol und hyperverzweigtes Polyglycerin der Adsorption von Plasmaproteinen und der Anhaftung von Bakterien widerstehen kann. Die Hydroxyl-Endgruppen von PolyGGE können mit Sulfaten funktionalisiert werden, um die antithrombogene Funktion der endothelialen Glykokalyx zu imitieren. PolyGGE wurde durch Polymerisation des kommerziell erhältlichen Monomers Glycerin Glycidyl ether synthetisiert, das als Mischung aus Mono-, Di- und Triglycidylether charakterisiert wurde. Die kationische Ringöffnungspolymerisation dieses Monomers wurde mit Hilfe des Photoinitiators Diphenyliodoniumhexafluorophosphat durch Ultraviolett (UV) ausgelöst. Mit zunehmender UV-Härtungszeit nahmen mehr Epoxide in den Seitenketten der Monomere an der chemischen Vernetzung teil, was zu einem Anstieg des Elastizitätsmoduls führte, während der Wert der Bruchdehnung von polyGGE zunächst aufgrund der Ausbreitung der Polymerketten anstieg und dann mit zunehmender Vernetzungsdichte abnahm. Schließlich kann die Kettenausbreitung durch wässrige Kaliumhydroxidlösung wirksam gestoppt werden. PolyGGE wies im hydratisierten Zustand bei Körpertemperatur andere Zugeigenschaften auf als im trockenen Zustand bei Raumtemperatur. Sowohl der Elastizitätsmodul als auch die Werte der Bruchdehnung waren deutlich reduziert, wenn sie in Wasser bei 37 °C getestet wurden, was oberhalb der Glasübergangstemperatur von PolyGGE lag. Unter physiologischen Bedingungen entfalteten sich die Verflechtungen der PolyGGE-Netzwerke und das freie Volumen der Netzwerke wurde durch Wassermoleküle als Weichmacher ersetzt, was die Mobilität der Polymerketten erhöhte und zu einem niedrigeren Elastizitätsmodul führte. Die Proteinadsorptionsanalyse wurde an PolyGGE-Filmen mit 30-minütiger UV-Härtung unter Verwendung eines Enzymimmunoassays durchgeführt. PolyGGE konnte die Adsorption von Fibrinogen, Albumin und Fibronektin aus menschlichem Plasma an der Grenzfläche zwischen menschlichem Plasma und PolyGGE-Filmen wirksam verhindern. Die Proteinresistenz von PolyGGE war vergleichbar mit den Negativkontrollen: dem hämokompatiblen Polydimethylsiloxan, was sein Potenzial als Beschichtungsmaterial für kardiovaskuläre Implantate zeigt. Darüber hinaus zeigten antimikrobielle Tests der bakteriellen Aktivität mittels isothermischer Mikrokalorimetrie und das mikroskopische Bild der direkten Bakterienkultur, dass PolyGGE die Biofilmbildung und das Wachstum sowohl von gramnegativen als auch von antibiotikaresistenten grampositiven Bakterien direkt stören kann, was auf die potenzielle Anwendung von PolyGGE zur Bekämpfung des Risikos von Krankenhausinfektionen und zur Verhinderung der Ausbreitung arzneimittelresistenter Superbugs hinweist. Um die Zellkompatibilität zu untersuchen, wurden polyGGE-Folien mit verschiedenen Lösungsmitteln (Ethanol, Chloroform, Aceton) und Zellkulturmedium extrahiert. Indirekte Zytotoxizitätstests zeigten, dass die extrahierten polyGGE-Filme immer noch eine toxische Wirkung auf L929-Fibroblastenzellen hatten. Die Hochleistungsflüssigkeitschromatographie/Elektrospray-Ionisations-Massenspektrometrie zeigte das Auftreten von chlororganischen Derivaten, die während der Interaktion zwischen Polymer und Zellkulturmedium freigesetzt wurden. Ein konstantes Niveau dieser chlororganischen Derivate wurde vom GGE-Monomer durch einen spezifischen C-Cl-Streckungspeak im Infrarotspektrum von GGE bestätigt. Es wird angenommen, dass dies der Hauptgrund für die erhöhte Permeabilität der Zellmembran und die verringerte Stoffwechselaktivität ist, was zum Zelltod führt. Es wurden Versuche unternommen, die Lösungsmittel zu wechseln, um die toxischen Substanzen zu entfernen, aber die Freisetzung dieser kleinen Moleküle scheint nur langsam zu erfolgen. Die dicht vernetzten polyGGE-Netzwerke können möglicherweise zum Einschluss chloridhaltiger Verbindungen beitragen. Diese Ergebnisse liefern wertvolle Informationen für die Erforschung potenzieller toxischer Substanzen, die aus PolyGGE-Netzwerken ausgewaschen werden, und schlagen eine praktikable Strategie zur Minimierung der Zytotoxizität durch Verringerung der Vernetzungsdichte vor. Als Reagenzien für die Sulfatierung von PolyGGE-Oberflächen wurden Sulfaminsäure und N-Methyl-2-Pyrrolidon (NMP) gewählt. Die Fourier-Transformations-Infrarotspektroskopie mit abgeschwächter Totalreflexion (ATR-FT-IR) wurde zur Überwachung der Funktionalisierungskinetik eingesetzt, und die Ergebnisse bestätigten die erfolgreiche Sulfatpfropfung auf der Oberfläche von PolyGGE mit der kovalenten Bindung -C-O-S-. Mit Hilfe der Röntgen-Photoelektronenspektroskopie wurde die Elementzusammensetzung auf der Oberfläche und der Querschnitt des funktionalisierten PolyGGE bestimmt, und die Sulfatierung innerhalb von 15 Minuten garantiert, dass die Sulfatierung nur auf der Oberfläche stattfindet, während sie in der Masse des Polymers nicht vorkommt. Die Konzentration der gepfropften Sulfate nahm mit zunehmender Reaktionszeit zu. Die Hydrophilie der Oberfläche von polyGGE wurde durch die Zunahme negativ geladener Endgruppen stark erhöht. Für die PolyGGE-Sulfate wurden drei Sterilisationstechniken verwendet: Autoklavieren, Gammastrahlenbestrahlung und Ethylenoxid (EtO)-Sterilisation. Die Ergebnisse der quantitativen ATR-FT-IR und Toluidinblau O-Untersuchung zeigten den vollständigen Verlust der Sulfate nach der Sterilisation im Autoklaven, was auch durch den erhöhten Wasserkontaktwinkel bestätigt wurde. Bei den mit Gammastrahlen und im Autoklaven sterilisierten PolyGGE-Sulfaten wurde nur ein geringer Einfluss auf die Sulfatkonzentration festgestellt. Um den thermischen Einfluss auf PolyGGE-Sulfate zu untersuchen, bestand eine Strategie darin, ein Poly(hydroxyethylacrylat)-Sulfat (PHEAS) für die Modellierung zu verwenden. Das Profil der thermogravimetrischen Analyse von PHEAS zeigte, dass Sulfate unabhängig von den Substratmaterialien thermisch nicht stabil sind und die Zersetzung der Sulfate bei etwa 100 °C stattfindet. Obwohl die Gammasterilisation ebenfalls kaum negative Auswirkungen auf den Sulfatgehalt hat, deutet die Farbveränderung der PolyGGE-Sulfate darauf hin, dass chemische oder physikalische Veränderungen im Polymer auftreten könnten. Die EtO-Sterilisation erwies sich als die am besten geeignete Sterilisationstechnik, um die chemische Struktur der PolyGGE-Sulfate zu erhalten. Zusammenfassend lässt sich sagen, dass die durchgeführte Arbeit bewiesen hat, dass PolyGGE als Antifouling-Beschichtungsmaterial verwendet werden kann und sein antimikrobielles Potenzial zeigt. Die Funktionalisierung der Sulfate kann mit Sulfaminsäure/NMP effektiv durchgeführt werden. Die EtO-Sterilisation ist die am besten geeignete Sterilisationstechnik für gepfropfte Sulfate. Darüber hinaus bietet diese Arbeit auch eine gute Strategie für die Analyse toxischer auslaugbarer Substanzen mit Hilfe geeigneter physikalisch-chemischer Charakterisierungstechniken. Zukünftige Arbeiten werden sich darauf konzentrieren, die Freisetzung toxischer Substanzen durch Verringerung der Vernetzungsdichte zu minimieren bzw. zu eliminieren. Ein weiterer interessanter Aspekt ist die Untersuchung, ob gepfropfte Sulfate den Anforderungen an die Anti-Thrombogenität gerecht werden können. KW - Sulfation KW - Antifouling KW - antimicrobial KW - Polyether Y1 - 2022 ER - TY - THES A1 - Zhao, Yuhang T1 - Synthesis and surface functionalization on plasmonic nanoparticles for optical applications N2 - This thesis focuses on the synthesis of novel functional materials based on plasmonic nanoparticles. Three systems with targeted surface modification and functionalization have been designed and synthesized, involving modified perylenediimide doped silica-coated silver nanowires, polydopamine or TiO2 coated gold-palladium nanorods and thiolated poly(ethylene glycol) (PEG-SH)/dodecanethiol (DDT) modified silver nanospheres. Their possible applications as plasmonic resonators, chiral sensors as well as photo-catalysts have been studied. In addition, the interaction between silver nanospheres and 2,3,5,6-Tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) molecules has also been investigated in detail. In the first part of the thesis, surface modification on Ag nanowires (NWs) with optimized silica coating through a modified Stöber method has been firstly conducted, employing sodium hydroxide (NaOH) to replace ammonia solution (NH4OH). The coated silver nanowires with a smooth silica shell have been investigated by single-particle dark-field scattering spectroscopy, transmission electron microscopy and electron-energy loss spectroscopy to characterize the morphologies and structural components. The silica-coated silver nanowires can be further functionalized with fluorescent molecules in the silica shell via a facile one-step coating method. The as-synthesized nanowire is further coupled with a gold nanosphere by spin-coating for the application of the sub-diffractional chiral sensor for the first time. The exciton-plasmon-photon interconversion in the system eases the signal detection in the perfectly matched 1D nanostructure and contributes to the high contrast of the subwavelength chiral sensing for the polarized light. In the second part of the thesis, dumbbell-shaped Au-Pd nanorods coated with a layer of polydopamine (PDA) or titanium dioxide (TiO2) have been constructed. The PDA- and TiO2- coated Au-Pd nanorods show a strong photothermal conversion performance under NIR illumination. Moreover, the catalytic performance of the particles has been investigated using the reduction of 4-nitrophenol (4-NP) as the model reaction. Under light irradiation, the PDA-coated Au-Pd nanorods exhibit a superior catalytic activity by increasing the reaction rate constant of 3 times. The Arrhenius-like behavior of the reaction with similar activation energies in the presence and absence of light irradiation indicates the photoheating effect to be the dominant mechanism of the reaction acceleration. Thus, we attribute the enhanced performance of the catalysis to the strong photothermal effect that is driven by the optical excitation of the gold surface plasmon as well as the synergy with the PDA layer. In the third part, the kinetic study on the adsorption of 2,3,5,6-Tetrafluoro-7,7,8,8-tetracyanoquino-dimethane (F4TCNQ) on the surface of Ag nanoparticles (Ag NPs) in chloroform has been reported in detail. Based on the results obtained from the UV-vis-NIR absorption spectroscopy, cryogenic transmission electron microscopy (cryo-TEM), scanning nano-beam electron diffraction (NBED) and electron energy loss spectroscopy (EELS), a two-step interaction kinetics has been proposed for the Ag NPs and F4TCNQ molecules. It includes the first step of electron transfer from Ag NPs to F4TCNQ indicated by the ionization of F4TCNQ, and the second step of the formation of Ag-F4TCNQ complex. The whole process has been followed via UV-vis-NIR absorption spectroscopy, which reveals distinct kinetics at two stages: the instantaneous ionization and the long-term complex formation. The kinetics and the influence of the molar ratio of Ag NPs/F4TCNQ molecules on the interaction between Ag NPs and F4TCNQ molecules in the organic solution are reported herein for the first time. Furthermore, the control experiment with silica-coated Ag NPs indicates that the charge transfer at the surface between Ag NPs and F4TCNQ molecules has been prohibited by a silica layer of 18 nm. KW - plasmonic nanoparticles KW - silica KW - polydopamine KW - TiO2 KW - chiral sensing KW - catalysis KW - surface interaction Y1 - 2021 ER - TY - THES A1 - Zhao, Li T1 - Sustainable approaches towards novel nitrogen-doped carbonaceous structures Y1 - 2010 CY - Potsdam ER - TY - THES A1 - Zhang, Weiyi T1 - Functional Poly(ionic liquid) Materials based on Poly(1,2,4-triazolium)s Y1 - 2017 ER - TY - THES A1 - Zhang, Shuhao T1 - Synthesis and self-assembly of protein-polymer conjugates for the preparation of biocatalytically active membranes T1 - Synthese und Selbstassemblierung von Protein/Polymer-Konjugaten für die Herstellung einer biokatalytisch aktiven Membran N2 - This thesis covers the synthesis of conjugates of 2-Deoxy-D-ribose-5-phosphate aldolase (DERA) with suitable polymers and the subsequent immobilization of these conjugates in thin films via two different approaches. 2-Deoxy-D-ribose-5-phosphate aldolase (DERA) is a biocatalyst that is capable of converting acetaldehyde and a second aldehyde as acceptor into enantiomerically pure mono- and diyhydroxyaldehydes, which are important structural motifs in a number of pharmaceutically active compounds. Conjugation and immobilization renders the enzyme applicable for utilization in a continuously run biocatalytic process which avoids the common problem of product inhibition. Within this thesis, conjugates of DERA and poly(N-isopropylacrylamide) (PNIPAm) for immobilization via a self-assembly approach were synthesized and isolated, as well as conjugates with poly(N,N-dimethylacrylamide) (PDMAA) for a simplified and scalable spray-coating approach. For the DERA/PNIPAm-conjugates different synthesis routes were tested, including grafting-from and grafting-to, both being common methods for the conjugation. Furthermore, both lysines and cysteines were addressed for the conjugation in order to find optimum conjugation conditions. It turned out that conjugation via lysine causes severe activity loss as one lysine plays a key role in the catalyzing mechanism. The conjugation via the cysteines by a grafting-to approach using pyridyl disulfide (PDS) end-group functionalized polymers led to high conjugation efficiencies in the presence of polymer solubilizing NaSCN. The resulting conjugates maintained enzymatic activity and also gained high acetaldehyde tolerance which is necessary for their use later on in an industrial relevant process after their immobilization. The resulting DERA/PNIPAm conjugates exhibited enhanced interfacial activity at the air/water interface compared to the single components, which is an important pre-requisite for the immobilization via the self-assembly approach. Conjugates with longer polymer chains formed homogeneous films on silicon wafers and glass slides while the ones with short chains could only form isolated aggregates. On top of that, long chain conjugates showed better activity maintenance upon the immobilization. The crosslinking of conjugates, as well as their fixation on the support materials, are important for the mechanical stability of the films obtained from the self-assembly process. Therefore, in a second step, we introduced the UV-crosslinkable monomer DMMIBA to the PNIPAm polymers to be used for conjugation. The introduction of DMMIBA reduced the lower critical solution temperature (LCST) of the polymer and thus the water solubility at ambient conditions, resulting in lower conjugation efficiencies and in turn slightly poorer acetaldehyde tolerance of the resulting conjugates. Unlike the DERA/PNIPAm, the conjugates from the copolymer P(NIPAM-co-DMMIBA) formed continuous, homogenous films only after the crosslinking step via UV-treatment. For a firm binding of the crosslinked films, a functionalization protocol for the model support material cyclic olefin copolymer (COC) and the final target support, PAN based membranes, was developed that introduces analogue UV-reactive groups to the support surface. The conjugates immobilized on the modified COC films maintained enzymatic activity and showed good mechanical stability after several cycles of activity assessment. Conjugates with longer polymer chains, however, showed a higher degree of crosslinking after the UV-treatment leading to a pronounced loss of activity. A porous PAN membrane onto which the conjugates were immobilized as well, was finally transferred to a dead end filtration membrane module to catalyze the aldol reaction of the industrially relevant mixture of acetaldehyde and hexanal in a continuous mode. Mono aldol product was detectable, but yields were comparably low and the operational stability needs to be further improved Another approach towards immobilization of DERA conjugates that was followed, was to generate the conjugates in situ by simply mixing enzyme and polymer and spray coat the mixture onto the membrane support. Compared to the previous approach, the focus was more put on simplicity and a possible scalability of the immobilization. Conjugates were thus only generated in-situ and not further isolated and characterized. For the conjugation, PDMAA equipped with N-2-thiolactone acrylamide (TlaAm) side chains was used, an amine-reactive comonomer that can react with the lysine residues of DERA, as well as with amino groups introduced to a desired support surface. Furthermore disulfide formation after hydrolysis of the Tla groups causes a crosslinking effect. The synthesized copolymer poly(N,N-Dimethylacrylamide-co-N-2-thiolactone acrylamide) (P(DMAA-co-TlaAm)) thus serves a multiple purpose including protein binding, crosslinking and binding to support materials. The mixture of DERA and polymer could be immobilized on the PAN support by spray-coating under partial maintenance of enzymatic activity. To improve the acetaldehyde tolerance, the polymer in used was further equipped with cysteine reactive PDS end-groups that had been used for the conjugation as described in the first part of the thesis. The generated conjugates indeed showed good acetaldehyde tolerance and were thus used to be coated onto PAN membrane supports. Post treatment with a basic aqueous solution of H2O2 was supposed to further crosslink the spray-coated film hydrolysis and oxidation of the thiolactone groups. However, a washing off of the material was observed. Optimization is thus still necessary. N2 - Die vorliegende Arbeit beschreibt die Synthese von Konjugaten aus 2-Deoxy-D-ribose-5-phosphat aldolase (DERA) und geeigneten Polymeren sowie deren nachfolgende Immobilisierung in dünnen Filmen mittels zwei verschiedener Herangehensweisen. DERA ist ein Biokatalysator, der in der Lage ist, Acetaldehyd mit einem weiteren Aldehyd zu enantiomerenreinen Mono- und Dihydroxyaldehyden zu verknüpfen. Diese Verbindungen sind wichtige Strukturmotive für eine Reihe von pharmazeutisch aktiven Verbindungen. Konjugation und Immobilisierung machen das Enzym nutzbar für den Einsatz in einem kontinuierlich betriebenen, biokatalytischen Prozess, welcher das bekannte Problem der Produktinhibierung umgeht. In der vorliegenden Arbeit wurden einerseits Konjugate aus DERA und Poly(N-isopropylacrylamid) (PNIPAm) für die Immobilisierung mittels eines Selbstassemblierungsverfahrens synthetisiert und isoliert, sowie andererseits entsprechende Konjugate mit Poly(N,N-dimethylacrylamid) (PDMAA) für ein vereinfachtes und skalierbares Immobilisierungsverfahren mittels Sprühauftrag hergestellt. Für die DERA/PNIPAm-Konjugate wurden verschiedene Syntheserouten getestet, einschließlich grafting-from und grafting-to. Beide Methoden werden standardmäßig für entsprechende Konjugationen eingesetzt. Weiterhin wurden sowohl die Lysine als auch die Cysteine des Enzyms für die Konjugation herangezogen, um optimale Konjugationsbedingungen zu finden. Konjugation über die Lysine verursachte deutliche Aktivitätsverluste, da ein Lysin auch die Schlüsselrolle im katalytischen Mechanismus des Enzyms spielt. Die Konjugation über die Cysteine sowie einen grafting-to-Ansatz unter Nutzung eines entsprechenden Polymers mit cysteinreaktiver Pyridyldisulfid-Endgruppe (PDS) führte zu einer hohen Konjugationseffizienz, sofern polymersolubilisierendes NaSCN eingesetzt wurde. Die resultierenden Konjugate behielten ihre enzymatische Aktivität bei deutlich gesteigerter Toleranz gegenüber Acetaldehyd. Beide Aspekte sind wichtig für den Einsatz des Enzyms in einem industriell relevanten Prozess nach dem Immobilisierungsschritt. Die DERA/PNIPAm-Konjugate zeigten eine erhöhte Oberflächenaktivität im Vergleich zu den Einzelkomponenten, was eine wichtige Voraussetzung für die Immobilisierung über eine Selbstassemblierung darstellt. Konjugate mit relativ langen Polymerketten bildeten nach dem Selbstassemblierungsschritt homogene Filme auf Silizium-Wafern und Glass-Objektträgern während Konjugate mit kurzen Ketten nur isolierte Aggregate bildeten. Darüber hinaus zeigten die Konjugate mit längeren Ketten einen besseren Erhalt der Enzymaktivität im Zuge der Immobilisierung. Die nachträgliche Vernetzung der Konjugate, sowie ihre feste Anbindung an die Trägermaterialien sind wichtige Voraussetzungen für die mechanische Stabilität des aus dem Selbstassemblierungsschritt erhaltenen Films. Aus diesem Grund wurde in einem zweiten Schritt das UV-vernetzbare Monomer DMMIBA in das für die Konjugation vorgesehene, PNIPAm-basierte Polymer eingeführt. Die Einbindung von DMMIBA setzte die untere kritische Lösungstemperatur (LCST) und damit die Löslichkeit des Polymers in Wasser bei Raumtemperatur herab. Dies führte zu niedrigeren Konjugationseffizienzen und damit zu einer etwas schlechteren Acetaldehydtoleranz der resultierenden Konjugate. Anders als im Fall von DERA/PNIPAm, bildeten die mit P(NIPAM-co-DMMIBA) synthetisierten Konjugate einen homogenen Film nur nach Vernetzung mittels UV-Behandlung aus. Für eine feste Anbindung des vernetzten Films wurde ein Funktionalisierungsprotokoll für das Modell-Trägermaterial aus cycloolefinischem Copolymer (COC) und das letztliche Zielmaterial, PAN-basierte Membranen, entwickelt, welches analoge UV-reaktive Gruppen auf der Trägeroberfläche erzeugt. Die auf COC immobilisierten Konjugate bewahrten ihre Enzymaktivität und zeigten eine gute mechanische Stabilität nach mehreren Aktivitäts-Messzyklen. Der Einsatz von Konjugaten mit längeren Polymerketten führte jedoch zu Filmen mit zu hohem Vernetzungsgrad was einen deutlichen Aktivitätsverlust bedingte. Eine poröse, PAN-basierte Membran, auf welcher die Konjugate ebenso immobilisiert wurden, wurde schlussendlich in ein Dead-End-Filtrationsmodul überführt, um die Aldolreaktion eines industriell relevanten Gemisches aus Acetaldehyd und Hexanal in einem kontinuierlich betriebenen Verfahren durchzuführen. Es konnte Monoaldolprodukt detektiert werden, jedoch waren die Ausbeuten vergleichsweise niedrig, während sich die operative Stabilität als verbesserungswürdig erwies. Ein weiterer Immobilisierungsansatz für DERA-Konjugate, beinhaltete die in-situ-Generierung der Konjugate durch einfaches Vermischen von Enzym und Polymer gefolgt von unmittelbaren Auftrag des Materials auf ein Membranträgermaterial mittels Sprühen. Im Vergleich zum ersten Ansatz lag der Fokus hier mehr auf der Einfachheit und prinzipiellen Skalierbarkeit der Immobilisierung. Daher wurden die Konjugate hier nur in-situ erzeugt und nicht weiter isoliert sowie charakterisiert. Für die Konjugation wurde PDMAA herangezogen, welches mit Thiolactongruppen entlang der Seitenkette ausgerüstet ist. Die Thiolactongruppen sind reaktiv gegenüber Aminen und können daher sowohl mit den Lysineinheiten der DERA reagieren als auch mit Aminogruppen, die im Vorfeld auf dem Trägermaterial erzeugt wurden. Darüber hinaus können durch Hydrolyse der Thiolactoneinheiten sowie anschließender Ausbildung von Disulfidbrücken Vernetzungspunkte erzeugt werden. Das hergestellte Copolymer poly(N,N-Dimethylacrylamide-co-N-2-thiolactone acrylamide) (P(DMAA-co-TlaAm) übernimmt daher mehrere Aufgaben einschließlich Proteinbindung, Vernetzung und Anbindung an das Trägermaterial. Mischungen aus DERA und Polymer konnten durch Sprühauftrag auf funktionalisierten PAN-Trägermaterialien unter teilweisem Erhalt der Enzymaktivität immobilisiert werden. Um auch hier die Acetaldehydtoleranz zu verbessern, wurde das Polymer in einem zweiten Schritt wieder mit PDS-Endgruppen ausgerüstet, die schon zuvor im ersten Teil der Arbeit für die Konjugatsynthese mittels grafting-to herangezogen wurden. Die hergestellten Konjugate zeigten eine gute Acetaldehydtoleranz und wurden daher verwendet, um PAN-Membranen zu beschichten. Eine Nachbehandlung mittels einer basischen Wasserstoffperoxidlösung sollte den aufgesprühten Film vernetzen. Im Ergebnis wurde jedoch ein großer Teil des aufgebrachten Materials im Zuge dieses Schritts heruntergewaschen. Eine weitere Optimierung dieses Schritts ist daher noch notwendig. KW - 2-deoxy-D-ribose-5-phoshphate aldolase KW - enzyme immobilization KW - enzymatically active membrane KW - enzyme/polymer conjugate KW - self-assembly Y1 - 2019 ER - TY - THES A1 - Zhang, Quanchao T1 - Shape-memory properties of polymeric micro-scale objects prepared by electrospinning and electrospraying N2 - The ongoing trend of miniaturizing multifunctional devices, especially for minimally-invasive medical or sensor applications demands new strategies for designing the required functional polymeric micro-components or micro-devices. Here, polymers, which are capable of active movement, when an external stimulus is applied (e.g. shape-memory polymers), are intensively discussed as promising material candidates for realization of multifunctional micro-components. In this context further research activities are needed to gain a better knowledge about the underlying working principles for functionalization of polymeric micro-scale objects with a shape-memory effect. First reports about electrospun solid microfiber scaffolds, demonstrated a much more pronounced shape-memory effect than their bulk counterparts, indicating the high potential of electrospun micro-objects. Based on these initial findings this thesis was aimed at exploring whether the alteration of the geometry of micro-scale electrospun polymeric objects can serve as suitable parameter to tailor their shape-memory properties. The central hypothesis was that different geometries should result in different degrees of macromolecular chain orientation in the polymeric micro-scale objects, which will influence their mechanical properties as well as thermally-induced shape-memory function. As electrospun micro-scale objects, microfiber scaffolds composed of hollow microfibers with different wall thickness and electrosprayed microparticles as well as their magneto-sensitive nanocomposites all prepared from the same polymer exhibiting pronounced bulk shape-memory properties were investigated. For this work a thermoplastic multiblock copolymer, named PDC, with excellent bulk shape-memory properties, associated with crystallizable oligo(ε-caprolactone) (OCL) switching domains, was chosen for the preparation of electrospun micro-scale objects, while crystallizable oligo(p-dioxanone) (OPDO) segments serve as hard domains in PDC. In the first part of the thesis microfiber scaffolds with different microfiber geometries (solid or hollow with different wall thickness) were discussed. Hollow microfiber based PDC scaffolds were prepared by coaxial electrospinning from a 1, 1, 1, 3, 3, 3 hexafluoro-2-propanol (HFP) solution with a polymer concentration of 13% w·v-1. Here as a first step core-shell fiber scaffolds consisting of microfibers with a PDC shell and sacrificial poly(ethylene glycol) (PEG) core are generated. The hollow PDC microfibers were achieved after dissolving the PEG core with water. The utilization of a fixed electrospinning setup and the same polymer concentration of the PDC spinning solution could ensure the fabrication of microfibers with almost identical outer diameters of 1.4 ± 0.3 µm as determined by scanning electron microscopy (SEM). Different hollow microfiber wall thicknesses of 0.5 ± 0.2 and 0.3 ± 0.2 µm (analyzed by SEM) have been realized by variation of the mass flow rate, while solid microfibers were obtained by coaxial electrospinning without supplying any core solution. Differential scanning calorimetry experiments and tensile tests at ambient temperature revealed an increase in degree of OCL crystallinity form χc,OCL = 34 ± 1% to 43 ± 1% and a decrease in elongation of break from 800 ± 40% to 200 ± 50% associated with an increase in Young´s modulus and failture stress for PDC hollow microfiber scaffolds when compared with soild fibers. The observed effects were enhanced with decreasing wall thickness of the single hollow fibers. The shape-memory properties of the electrospun PDC scaffolds were quantified by cyclic, thermomechanical tensile tests. Here, scaffolds comprising hollow microfibers exhibited lower shape fixity ratios around Rf = 82 ± 1% and higher shape recovery ratios of Rr = 67 ± 1% associated to more pronounced relaxation at constant strain during the first test cycle and a lower switching temperature of Tsw = 33 ± 1 °C than the fibrous meshes consisting of solid microfibers. These findings strongly support the central hypothesis that different fiber geometries (solid or hollow with different wall thickness) in electrospun scaffolds result in different degrees of macromolecular chain orientation in the polymeric micro-scale objects, which can be applied as design parameter for tailoring their mechanical and shape-memory properties. The second part of the thesis deals with electrosprayed particulate PDC micro-scale objects. Almost spherical PDC microparticles with diameters of 3.9 ± 0.9 μm (as determined by SEM) were achieved by electrospraying of HFP solution with a polymer concentration of 2% w·v-1. In contrast, smaller particles with sizes of 400 ± 100 nm or 1.2 ± 0.3 μm were obtained for the magneto-sensitive composite PDC microparticles containing 23 ± 0.5 wt% superparamagnetic magnetite nanoparticles (mNPs). All prepared PDC microparticles exhibited a similar overall crystallinity like the PDC bulk material as analyzed by DSC. AFM nanoindentation results revealed no influence of the nanofiller incorporation on the local mechanical properties represented by the reduced modulus determined for pure PDC microparticles and magneto-sensitive composite PDC microparticles with similar diameters around 1.3 µm. It was found that the reduced modulus of the nanocomposite microparticles increased substantially with decreasing particles size from 2.4 ± 0.9 GPa (1.2 µm) to 11.9 ± 3.1 GPa (0.4 µm), which can be related to a higher orientation of the macromolecules at the surface of smaller sized microparticles. The magneto-sensitivity of such nanocomposite microparticles could be demonstrated in two aspects. One was by attracting/collecting the composite micro-objects with an external permanent magnet. The other one was by a inductive heating to 44 ± 1 °C, which is well above the melting transition of the OCL switching domains, when compacted to a 10 x 10 mm2 film with a thickness of 10 µm and exposed to an alternating magnet field with an magnetic field strength of 30 kA·m-1. Both functions are of great relevance for designing next generation drug delivery systems combining targeting and on demand release. By a compression approach shape-memory functionalization of individual microparticles could be realized. Here different programming pressures and compression temperatures were applied. The shape-recovery capability of the programmed PDC microparticles was quantified by online and off-line heating experiments analyzed via microscopy measurement. The obtained shape-memory properties were found to be strongly depending on the applied programming pressure and temperature. The best shape-memory performance with a high shape recovery rate of about Rr = 80±1% was obtained when a low pressure of 0.2 MPa was applied at 55 °C. Finally, it was demonstrated that PDC microparticles can be utilized as micro building parts for preparation of a macroscopic film with temporary stability by compression of a densely packed array of PDC microparticles at 60 °C followed by subsequent cooling to ambient temperature. This film disintegrates into individual microparticles upon heating to 60 °C. Based on this technology the design of stable macroscopic release systems can be envisioned, which can be easily fixed at the site of treatment (i.e. by suturing) and disintegrate on demand to microparticles facilitating the drug release. In summary, the results of this thesis could confirm the central hypothesis that the variation of the geometry of polymeric micro-objects is a suitable parameter to adjust their shape-memory performance by changing the degree of macromolecular chain orientation in the specimens or by enabling new functions like on demand disintegration. These fundamental findings might be relevant for designing novel miniaturized multifunctional polymer-based devices. KW - shape-memory effect KW - microparticles KW - hollow microfibers KW - geometry Y1 - 2018 ER - TY - THES A1 - Zenichowski, Karl T1 - Quantum dynamical study of Si(100) surface-mounted, STM-driven switches at the atomic and molecular scale T1 - Quantendynamische Untersuchung von Si(100) Oberflächen-gebundenen, STM-gesteuerten atomaren und molekularen Schaltern N2 - The aim of this thesis is the quantum dynamical study of two examples of scanning tunneling microscope (STM)-controllable, Si(100)(2x1) surface-mounted switches of atomic and molecular scale. The first example considers the switching of single H-atoms between two dangling-bond chemisorption sites on a Si-dimer of the Si(100) surface (Grey et al., 1996). The second system examines the conformational switching of single 1,5-cyclooctadiene molecules chemisorbed on the Si(100) surface (Nacci et al., 2008). The temporal dynamics are provided by the propagation of the density matrix in time via an according set of equations of motion (EQM). The latter are based on the open-system density matrix theory in Lindblad form. First order perturbation theory is used to evaluate those transition rates between vibrational levels of the system part. In order to account for interactions with the surface phonons, two different dissipative models are used, namely the bilinear, harmonic and the Ohmic bath model. IET-induced vibrational transitions in the system are due to the dipole- and the resonance-mechanism. A single surface approach is used to study the influence of dipole scattering and resonance scattering in the below-threshold regime. Further, a second electronic surface was included to study the resonance-induced switching in the above-threshold regime. Static properties of the adsorbate, e.g., potentials and dipole function and potentials, are obtained from quantum chemistry and used within the established quantum dynamical models. N2 - Die vorliegende Doktorarbeit befasst sich mit kleinsten schaltbaren Einheiten in Form des Moleküls Cyclooctadien (COD) und dem Wasserstoff-Atom, die chemisch fest mit einer Oberfläche aus kristallinem Silizium verbunden sind. Jeder dieser Schalter kann mittels einer winzigen Spitze, eines so genannten Rastertunnelmikroskops (RTM), von atomarem Durchmesser in zwei unterscheidbare und stabile Schaltpositionen gebracht werden. Dabei besteht das Schalten entweder in einer Änderung der Geometrie des molekularen Schalters oder im Brechen und Neu-knüpfen chemischer Bindungen. Dabei ist es entscheidend, dass durch die geringe Grösse dieser Schalter eine hohe Anzahl dieser Schalter auf einer Oberfläche deponiert werden können. Mit der in den Schaltern speicherbaren Informationen an oder aus, 0 oder 1 ließen sich sehr hohe Speicherkapazitäten erreichen. Vor einer Anwendung dieser Art ist es wichtig zunächst ein grundlegendes Verständnis der Schaltprozesse auf der Oberfläche zu gewinnen. Wenn alle wesentlichen Faktoren berücksichtigt wurden und der Mechanismus des Schaltens verstanden ist, kann das Ergebnis des Experiments mit Hilfe eines theoretischen Modells vorhergesagt werden. Für die Handhabbarkeit muss sich das theoretisches Modell auf wesentliche Einflüsse beschränken und diese so einfach wie möglich beschreiben. So wurde die simultane Bewegung der 12 Atome des COD in die Bewegung eines gemittelten Massenpunktes entlang von einer oder von zwei räumlichen Freiheitsgraden übersetzt. Dabei kann der Massenpunkt im klassischen Bild anschaulich als eine rollende Kugel beschrieben werden, die in einer Seite einer Doppelmulde gefangen ist. Die Kugel kann durch äußere Anregung zum Schwingen gebracht werden und schließlich über eine Barriere in die benachbarte Mulde schalten. Nun muss die Schwingung der Kugel gebremst werden, um ein Zurück-Schwingen der Kugel zu verhindern. Die Anregung erfolgt durch elektrische Ladungen die von der Spitze des RTM zur Oberfläche wandern oder durch eine schwingende, d.h. warme Oberfläche. Das Bremsen wird über die elastische Bindung zu einer kalten Oberfläche vermittelt. Um Quanteneffekte wie das Tunneln der Kugel durch die Barriere zu beschreiben wurde die Kugel durch ein Wellenpaket beschrieben und dessen Aufenthaltswahrscheinlichkeit in der Doppelmulde untersucht. Im Fall des Wasserstoffatoms war die experimentelle Prüfung des entworfenen Modells für ein Schalten bei starkem Strom leider nicht möglich. Für das COD Molekül konnte jedoch nicht nur die Übereinstimmung mit den experimentellen Befunden, sondern im Fall des Schaltens in Abhängigkeit der Oberflächentemperatur auch die Vorhersagefähigkeit des Modells unter Beweis gestellt werden. KW - Kerndynamik KW - molekulare Schalter KW - Nanotechnologie KW - STM KW - Oberflächen KW - Quantum dynamics KW - molecular switches KW - nanotechnology KW - STM KW - surfaces Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-62156 ER - TY - THES A1 - Zehm, Daniel T1 - Amphiphile Block-Bürstenpolymere : ihre Synthese durch sequentielle Anwendung von CRP-Methoden und ihre Selbstorganisation in ausgewählten Lösungsmitteln Y1 - 2010 CY - Potsdam ER - TY - THES A1 - Zarafshani, Zoya T1 - Chain-end functionalization and modification of polymers using modular chemical reactions T1 - Ketten-Ende Funktionalisierung und Modifikation von Polymeren mittels modulare chemischen Reaktionen N2 - Taking advantage of ATRP and using functionalized initiators, different functionalities were introduced in both α and ω chain-ends of synthetic polymers. These functionalized polymers could then go through modular synthetic pathways such as click cycloaddition (copper-catalyzed or copper-free) or amidation to couple synthetic polymers to other synthetic polymers, biomolecules or silica monoliths. Using this general strategy and designing these co/polymers so that they are thermoresponsive, yet bioinert and biocompatible with adjustable cloud point values (as it is the case in the present thesis), the whole generated system becomes "smart" and potentially applicable in different branches. The applications which were considered in the present thesis were in polymer post-functionalization (in situ functionalization of micellar aggregates with low and high molecular weight molecules), hydrophilic/hydrophobic tuning, chromatography and bioconjugation (enzyme thermoprecipitation and recovery, improvement of enzyme activity). Different α-functionalized co/polymers containing cholesterol moiety, aldehyde, t-Boc protected amine, TMS-protected alkyne and NHS-activated ester were designed and synthesized in this work. N2 - In dieser Arbeit wurden mittels der ATRP Methode sowie durch Benutzung funktioneller Initiatoren verschiedene Funktionalitäten an der α- und ω-Position der synthetischen Polymere (Kettenenden) eingeführt. Diese funktionalisierten Polymere können durch modulare synthetische Methoden wie z.B. die “Klick-Zykloaddition” (kupferkatalysiert oder auch kupferfreie Methoden möglich), Amidierung mit anderen synthetischen Polymeren oder Biomolekülen, oder auch mit Silikatmonolithen gekuppelt werden. Den beschriebenen Strategien folgend und unter Benutzung von thermoresponsiven, bioinerten und biokompartiblen (Co-) Polymeren mit einstellbaren Trübungspunkten können mittels Temperaturänderungen leicht steuerbare, „smarte“ Polymersysteme für verschiedene Anwendungen hergestellt werden. Im Rahmen dieser Arbeit wurden speziell Anwendungen wie die Postfunktionalisierung (in situ Funktionalisierung mizellarer Aggregate mit Molekülen, die sowohl niedrige als auch höhere Molekulargewichte aufweisen), hydrophiles/hydrophobes Tuning von Polymeren, Chromatographie an Polymeren sowie Biokonjugation von Polymeren (Enzymthermoprezipitation und -Gewinnung, Enzymaktivitätsmodifizierung) genauer untersucht. Es wurden verschiedene α-funktionalisierte (Co-)Polymere, die Cholesterol, Aldehyde, t-Boc geschützte Amine, TMS-geschützte Alkine und NHS-aktivierte Ester entwickelt und hergestellt und mittels passender ATRP Initiatoren eingeführt. KW - Atom Transfer Radical Polymerization KW - Klick-Chemie KW - Biokonjugation KW - Funktionalisierung KW - Modifizierung von Polymeren KW - ATRP KW - Click chemistry KW - Bioconjugation KW - Functionalization KW - Polymer Modification Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-59723 ER - TY - THES A1 - Zabel, Andre T1 - Halidometallate - Struktur und Eigenschaften Y1 - 2016 ER - TY - THES A1 - Yue, Xiuli T1 - Monolayer phase behavior of bipolar amphiphiles and their coupling with DNA Y1 - 2004 CY - Golm ER - TY - THES A1 - Yu, Linghui T1 - Hydrothermal synthesis of carbon and carbon nanocomposite materials for environmental and energy applications Y1 - 2013 CY - Potsdam ER - TY - THES A1 - Youk, Sol T1 - Molecular design of heteroatom-doped nanoporous carbons with controlled porosity and surface polarity for gas physisorption and energy storage N2 - The world energy consumption has constantly increased every year due to economic development and population growth. This inevitably caused vast amount of CO2 emission, and the CO2 concentration in the atmosphere keeps increasing with economic growth. To reduce CO2 emission, various methods have been developed but there are still many bottlenecks to be solved. Solvents easily absorbing CO2 such as monoethanol-amine (MEA) and diethanolamine, for example, have limitations of solvent loss, amine degradation, vulnerability to heat and toxicity, and the high cost of regeneration which is especially caused due to chemisorption process. Though some of these drawbacks can be compensated through physisorption with zeolites and metal-organic frameworks (MOFs) by displaying significant adsorption selectivity and capacity even in ambient conditions, limitations for these materials still exist. Zeolites demand relatively high regeneration energy and have limited adsorption kinetics due to the exceptionally narrow pore structure. MOFs have low stability against heat and moisture and high manufacturing cost. Nanoporous carbons have recently received attention as an attractive functional porous material due to their unique properties. These materials are crucial in many applications of modern science and industry such as water and air purification, catalysis, gas separation, and energy storage/conversion due to their high chemical and thermal stability, and in particular electronic conductivity in combination with high specific surface areas. Nanoporous carbons can be used to adsorb environmental pollutants or small gas molecules such as CO2 and to power electrochemical energy storage devices such as batteries and fuel cells. In all fields, their pore structure or electrical properties can be modified depending on their purposes. This thesis provides an in-depth look at novel nanoporous carbons from the synthetic and the application point of view. The interplay between pore structure, atomic construction, and the adsorption properties of nanoporous carbon materials are investigated. Novel nanoporous carbon materials are synthesized by using simple precursor molecules containing heteroatoms through a facile templating method. The affinity, and in turn the adsorption capacity, of carbon materials toward polar gas molecules (CO2 and H2O) is enhanced by the modification of their chemical construction. It is also shown that these properties are important in electrochemical energy storage, here especially for supercapacitors with aqueous electrolytes which are basically based on the physisorption of ions on carbon surfaces. This shows that nanoporous carbons can be a “functional” material with specific physical or chemical interactions with guest species just like zeolites and MOFs. The synthesis of sp2-conjugated materials with high heteroatom content from a mixture of citrazinic acid and melamine in which heteroatoms are already bonded in specific motives is illustrated. By controlling the removal procedure of the salt-template and the condensation temperature, the role of salts in the formation of porosity and as coordination sites for the stabilization of heteroatoms is proven. A high amount of nitrogen of up to 20 wt. %, oxygen contents of up to 19 wt.%, and a high CO2/N2 selectivity with maximum CO2 uptake at 273 K of 5.31 mmol g–1 are achieved. Besides, the further controlled thermal condensation of precursor molecules and advanced functional properties on applications of the synthesized porous carbons are described. The materials have different porosity and atomic construction exhibiting a high nitrogen content up to 25 wt. % as well as a high porosity with a specific surface area of more than 1800 m2 g−1, and a high performance in selective CO2 gas adsorption of 62.7. These pore structure as well as properties of surface affect to water adsorption with a remarkably high Qst of over 100 kJ mol−1 even higher than that of zeolites or CaCl2 well known as adsorbents. In addition to that, the pore structure of HAT-CN-derived carbon materials during condensation in vacuum is fundamentally understood which is essential to maximize the utilization of porous system in materials showing significant difference in their pore volume of 0.5 cm3 g−1 and 0.25 cm3 g−1 without and with vacuum, respectively. The molecular designs of heteroatom containing porous carbon derived from abundant and simple molecules are introduced in the presented thesis. Abundant precursors that already containing high amount of nitrogen or oxygen are beneficial to achieve enhanced interaction with adsorptives. The physical and chemical properties of these heteroatom-doped porous carbons are affected by mainly two parameters, that is, the porosity from the pore structure and the polarity from the atomic composition on the surface. In other words, controlling the porosity as well as the polarity of the carbon materials is studied to understand interactions with different guest species which is a fundamental knowledge for the utilization on various applications. N2 - Nanoporöse Kohlenstoffe haben in letzter Zeit aufgrund ihrer einzigartigen Eigenschaften als ein attraktives funktionelles poröses Material Aufmerksamkeit erregt. Diese Materialien sind aufgrund ihrer hohen chemischen und thermischen Stabilität und insbesondere aufgrund ihrer elektronischen Leitfähigkeit in Kombination mit hohen spezifischen Oberflächen von entscheidender Bedeutung für viele Anwendungen der modernen Wissenschaft und Industrie wie Wasser- und Luftreinigung, Katalyse, Gastrennung und Energiespeicherung/-umwandlung. Nanoporöse Kohlenstoffe können verwendet werden, um Umweltschadstoffe oder kleine Gasmoleküle wie CO2 zu adsorbieren und elektrochemische Energiespeicher wie Batterien und Brennstoffzellen anzutreiben. Ihre Porenstruktur oder ihre elektrischen Eigenschaften je nach Einsatzzweck modifiziert werden. Diese Arbeit bietet einen eingehenden Blick auf neuartige nanoporöse Kohlenstoffe aus synthetischer und anwendungstechnischer Sicht. Das Zusammenspiel zwischen Porenstruktur, atomarem Aufbau und den Adsorptionseigenschaften von nanoporösen Kohlenstoffmaterialien wird untersucht. Neuartige nanoporöse Kohlenstoffmaterialien werden unter Verwendung einfacher Vorläufermoleküle, die Heteroatome enthalten, durch ein einfaches Templatverfahren synthetisiert. Die Affinität und damit die Adsorptionskapazität von Kohlenstoffmaterialien gegenüber polaren Gasmolekülen (CO2 und H2O) wird durch die Modifikation ihres chemischen Aufbaus erhöht. Es wird auch gezeigt, dass diese Eigenschaften bei der elektrochemischen Energiespeicherung wichtig sind. Hier insbesondere für Superkondensatoren mit wässrigen Elektrolyten, die grundsätzlich auf der Physisorption von Ionen an Kohlenstoffoberflächen beruhen. Dies zeigt, dass nanoporöse Kohlenstoffe, genauso wie Zeolithen und MOFs, ein „funktionelles“ Material mit spezifischen physikalischen oder chemischen Wechselwirkungen mit Gastspezien sein können. Mit den Vorteilen einer hohen elektrischen Leitfähigkeit, einer gut entwickelten Porenstruktur und einer stark hydrophilen Oberflächenstruktur sind nanoporöse Kohlenstoffe vielversprechende Materialien, die weitreichende Auswirkungen auf verschiedene Bereiche des zukünftigen Energiebedarfs haben. KW - porous carbon KW - gas adsorption KW - energy storage KW - N-doped carbon KW - poröser Kohlenstoff KW - Gasadsorption KW - Energiespeicher KW - N-dotierter Kohlenstoff Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-539098 ER - TY - THES A1 - You, Zewang T1 - Conformational transition of peptide-functionalized cryogels enabling shape-memory capability Y1 - 2017 ER - TY - THES A1 - You, Liangchen T1 - Synthesis and characterization of novel glycopolymers Y1 - 2007 CY - Potsdam ER - TY - THES A1 - Yin, Jian T1 - Syntheses and transformations of 2-C-Malonyl substituted carbohydrates Y1 - 2009 CY - Potsdam ER - TY - THES A1 - Yan, Wan T1 - Shape-Memory effects of thermoplatic multiblock copolymers with overlapping thermal transitions Y1 - 2021 ER - TY - THES A1 - Yan, Runyu T1 - Nitrogen-doped and porous carbons towards new energy storage mechanisms for supercapacitors with high energy density T1 - Neuartige Energiespeichermechanismen in porösen und stickstoffdotierten Kohlenstoffen für die Anwendung in Superkondensatoren mit hoher Energiedichte N2 - Supercapacitors are electrochemical energy storage devices with rapid charge/discharge rate and long cycle life. Their biggest challenge is the inferior energy density compared to other electrochemical energy storage devices such as batteries. Being the most widely spread type of supercapacitors, electrochemical double-layer capacitors (EDLCs) store energy by electrosorption of electrolyte ions on the surface of charged electrodes. As a more recent development, Na-ion capacitors (NICs) are expected to be a more promising tactic to tackle the inferior energy density due to their higher-capacity electrodes and larger operating voltage. The charges are simultaneously stored by ion adsorption on the capacitive-type cathode surface and via faradic process in the battery-type anode, respectively. Porous carbon electrodes are of great importance in these devices, but the paramount problems are the facile synthetic routes for high-performance carbons and the lack of fundamental understanding of the energy storage mechanisms. Therefore, the aim of the present dissertation is to develop novel synthetic methods for (nitrogen-doped) porous carbon materials with superior performance, and to reveal a deeper understanding energy storage mechanisms of EDLCs and NICs. The first part introduces a novel synthetic method towards hierarchical ordered meso-microporous carbon electrode materials for EDLCs. The large amount of micropores and highly ordered mesopores endow abundant sites for charge storage and efficient electrolyte transport, respectively, giving rise to superior EDLC performance in different electrolytes. More importantly, the controversial energy storage mechanism of EDLCs employing ionic liquid (IL) electrolytes is investigated by employing a series of porous model carbons as electrodes. The results not only allow to conclude on the relations between the porosity and ion transport dynamics, but also deliver deeper insights into the energy storage mechanism of IL-based EDLCs which is different from the one usually dominating in solvent-based electrolytes leading to compression double-layers. The other part focuses on anodes of NICs, where novel synthesis of nitrogen-rich porous carbon electrodes and their sodium storage mechanism are investigated. Free-standing fibrous nitrogen-doped carbon materials are synthesized by electrospinning using the nitrogen-rich monomer (hexaazatriphenylene-hexacarbonitrile, C18N12) as the precursor followed by condensation at high temperature. These fibers provide superior capacity and desirable charge/discharge rate for sodium storage. This work also allows insights into the sodium storage mechanism in nitrogen-doped carbons. Based on this mechanism, further optimization is done by designing a composite material composed of nitrogen-rich carbon nanoparticles embedded in conductive carbon matrix for a better charge/discharge rate. The energy density of the assembled NICs significantly prevails that of common EDLCs while maintaining the high power density and long cycle life. N2 - Superkondensatoren sind elektrochemische Energiespeicher, die eine hohe Lade-/Entladerate und Zyklensta-bilität aufweisen, deren größte Einschränkung derzeit jedoch bei ihrer im Vergleich zu anderen Speicherlösungen, wie etwa Batterien, geringen Energiedichte liegt. Im am weitesten verbreiteten Superkondensatortyp, dem elektrochemischen Doppelschichtkondensator (engl. electrochemical double-layer capacitor, EDLC), wird die Energie durch Elektrosorption der Elektrolytionen an die geladene Elektrodenoberfläche gespeichert. Der Natrium-Ionen-Kondensator (engl. Na-ion capacitor, NIC) ist eine neuere Entwicklung und löst das Problem der geringen Energiedichte durch Verwendung von Elektroden mit einer höheren Kapazität und Betriebsspannung. Dies wird dadurch erreicht, dass simultan anodenseitig ein faradayscher Prozess und kathodenseitig der Aufbau einer elektrochemischen Doppelschicht genutzt werden. Somit kommen die Vorteile beider Phänomene zum Tragen. Poröse Kohlenstoffelektroden sind wichtig für beide Speichersysteme, wobei die Entwicklung einfacher Syn-theserouten für die Herstellung von Hochleistungskohlenstoffen und der Aufbau eines grundlegenden Ver-ständnisses der dem Energiespeicher zugrunde liegenden Mechanismen die vordergründigen Herausforde-rungen sind. Daher ist es das Ziel der vorliegenden Dissertation, neue Methoden zur Synthese (stickstoffdo-tierter) Kohlenstoffmaterialien mit überlegener Leistung zu erschließen und eine tiefere Einsicht in die me-chanistischen Aspekte der Funktionsweise der eingangs vorgestellten Superkondensatorsysteme zu erhalten. Im ersten Teil der Arbeit wird eine neuartige Synthese von Kohlenstoff-Elektrodenmaterialien für EDLCs vor-gestellt, welche ein hohes Volumen an Mikroporen und hochgeordneten Mesoporen aufweisen. Durch deren Einsatz kann in verschiedenen Elektrolytsystemen eine herausragende Energiedichte erzielt werden. Umso bedeutender sind die Ergebnisse der Untersuchung des kontrovers diskutierten Energiespeichermechanismus in EDLCs mit Elektrolyten auf Basis ionischer Flüssigkeiten (engl. ionic liquids, ILs) und Elektroden aus porösen Modellkohlenstoffen. Aus diesen können nicht nur Rückschlüsse auf den Zusammenhang zwischen Porosität und Ionentransportdynamik gezogen werden, sondern sie lassen auch wichtige Erkenntnisse auf die Mechanismen des Ladungsspeichers in IL-basierten EDLCs zu, welche sich grundlegend von dem in lösungsmittelbasierten Elektrolyten vorherrschenden Mechanismus, der Bildung einer Kompressionsdoppelschicht, unterscheiden. Im zweiten Teil des Werks liegt der Fokus auf der Synthese stickstoffreicher poröser Kohlenstoffelektroden als Anoden für NICs und der Untersuchung der Vorgänge während der Natriumeinlagerung in solchen Syste-men. Freistehende, faserartige und stickstoffdotierte Kohlenstoffmaterialien wurden durch Elektrospinnen des stickstoffreichen Monomers Hexaazatriphenylen-hexacarbonitril (C18N12) gefolgt von dessen Kondensati-on bei hoher Temperatur erhalten. Diese Fasern überzeugen durch überragende Kapazität und eine hohe Lade-/Entladerate beim Natriumspei-chervorgang. In diesem Rahmen wurde auch der Mechanismus der Natriumeinlagerung in stickstoffdotierten Kohlenstoffen beleuchtet und auf Basis dieser Erkenntnisse wurde eine weitere Optimierung vorgenommen. Indem ein Kompositmaterial aus stickstoffreichen Kohlenstoffnanopartikeln in einer leitfähigen Kohlenstoffmatrix erzeugt wurde, konnte die Lade-/Entladerate abermals verbessert werden. Somit übertrifft die Energiedichte der so konstruierten NICs die gewöhnlicher EDLCs, während deren hohe Leistungsdichte und Lebensdauer erhalten bleibt. KW - porous carbons KW - supercapacitors KW - high energy density KW - energy storage mechanism KW - poröse Kohlenstoffe KW - Superkondensatoren KW - hohe Energiedichte KW - Energiespeichermechanismus Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-431413 ER - TY - THES A1 - Yagci, Yavuz Emre T1 - Synthesis of poly(tartar amide)s and poly-(gluco amide)s as antifreeze additives Y1 - 2008 CY - Potsdam ER - TY - THES A1 - Yagci, Yavuz Emre T1 - Synthesis of poly(tartar amide)s and poly-(gluco amide)s as antifreeze additives Y1 - 2008 CY - Potsdam ER - TY - THES A1 - Xiong, Tao T1 - Vibrationally resolved absorption, emission, resonance Raman and photoelectron spectra of selected organic molecules, associated radicals and cations T1 - Schwingungsaufgelöste Absorptions-, Emissions-, Resonanz-Raman- und Photoelektronenspektren ausgewählter organischer Moleküle, assoziierter Radikale und Kationen BT - a time-dependent approach BT - ein zeitabhängiger Ansatz N2 - Time-dependent correlation function based methods to study optical spectroscopy involving electronic transitions can be traced back to the work of Heller and coworkers. This intuitive methodology can be expected to be computationally efficient and is applied in the current work to study the vibronic absorption, emission, and resonance Raman spectra of selected organic molecules. Besides, the "non-standard" application of this approach to photoionization processes is also explored. The application section consists of four chapters as described below. In Chapter 4, the molar absorptivities and vibronic absorption/emission spectra of perylene and several of its N-substituted derivatives are investigated. By systematically varying the number and position of N atoms, it is shown that the presence of nitrogen heteroatoms has a negligible effect on the molecular structure and geometric distortions upon electronic transitions, while spectral properties are more sensitive: In particular the number of N atoms is important while their position is less decisive. Thus, N-substitution can be used to fine-tune the optical properties of perylene-based molecules. In Chapter 5, the same methods are applied to study the vibronic absorption/emission and resonance Raman spectra of a newly synthesized donor-acceptor type molecule. The simulated absorption/emission spectra agree fairly well with experimental data, with discrepancies being attributed to solvent effects. Possible modes which may dominate the fine-structure in the vibronic spectra are proposed by analyzing the correlation function with the aid of Raman and resonance Raman spectra. In the next two chapters, besides the above types of spectra, the methods are extended to study photoelectron spectra of several small diamondoid-related systems (molecules, radicals, and cations). Comparison of the photoelectron spectra with available experimental data suggests that the correlation function based approach can describe ionization processes reasonably well. Some of these systems, cationic species in particular, exhibit somewhat peculiar optical behavior, which presents them as possible candidates for functional devices. Correlation function based methods in a more general sense can be very versatile. In fact, besides the above radiative processes, formulas for non-radiative processes such as internal conversion have been derived in literature. Further implementation of the available methods is among our next goals. N2 - Molekülsysteme bestehen aus Kernen und Elektronen, deren viel kleinere Masse sie in die Lage versetzten, sich der Bewegung des ersteren augenblicklich anzupassen. Daher ist die Bewegung der Elektronen und Kerne in einer guten ersten Annäherung "unabhängig", und die Energie der Elektronen kann zuerst berechnet werden, vorausgesetzt, die Kerne sind stationär. Die so gewonnene elektronische Energie wird zur Abstoßungsenergie zwischen den Kernen addiert, um ein Potential zu erhalten, das die Bewegung der Kerne bestimmt. Quantenmechanisch können sowohl die Elektronen als auch die Kerne nur bestimmte Energieniveaus haben. Die molekulare vibronische (= Schwingung + Elektronik) Absorptionsspektroskopie beinhaltet den Übergang der Elektronen und Kerne von ihrem Anfangs- in ihren Endzustand durch Photonenabsorption. Die größere elektronische Übergangsenergie bestimmt die Position des Absorptionsmaximums, während die kleinere nukleare Schwingungsübergangsenergie (ohne Berücksichtigung von Translation und Rotation) die Position der Teilmaxima innerhalb des Absorptionsbereichs bestimmt, wodurch die vibronische Feinstruktur entsteht. Ähnliche Ideen gelten auch für die vibronische Emissionsspektroskopie. Die Resonanz-Raman-Spektroskopie untersucht die Energieänderung des einfallenden Photons (dessen Energie ausreichend ist, um die Elektronen in einen höheren elektronischen Zustand anzuregen), nachdem es mit dem Molekül wechselwirkt. Der Energiegewinn oder -verlust des einfallenden Photons bewirkt eine Änderung des Schwingungszustandes. Die Photoelektronenspektroskopie ist ähnlich wie die vibronische Absorption, benötigt aber in der Regel mehr Energie des einfallenden Photons, da neben der Anregung des Moleküls in einen höheren vibronischen Zustand zusätzliche Energie benötigt wird, um ein Elektron aus dem Molekül zu entfernen. Diese spektroskopischen Techniken liefern wertvolle Informationen über die elektronische und nukleare Bewegung des Moleküls. Theoretisch können wir eine zeitabhängige Korrelationsfunktion verwenden, um die Spektren zu simulieren. Die Korrelationsfunktion für die Absorption ist beispielsweise eine Funktion der Zeit, deren Entwicklung Informationen über die elektronischen Energien und die nukleare Bewegung enthält. Um das Absorptionsspektrum in Form von Energie zu erhalten, wird ein mathematisches Verfahren, die so genannte Fourier-Transformation, auf die zeitabhängige Korrelationsfunktion angewendet, um ein energieabhängiges Spektrum zu erhalten. Diese Methode wird auf ausgewählte organische Moleküle, darunter einige Radikale und Kationen, angewandt, um deren elektronisches und optisches Verhalten unter dem Einfluss von einfallendem Licht zu untersuchen und Einblicke in das Design neuer optoelektronischer Bauelemente zu gewinnen. Bei einigen Molekülen/Systemen wird die vibronische Feinstruktur durch Faktoren wie molekulare Zusammensetzung und Umgebung wie Lösungsmittel beeinflusst, was darauf hindeutet, dass diese Systeme zur Feinabstimmung der gewünschten Eigenschaften verwendet werden können. Für andere Systeme gibt es fast keine sichtbare vibronische Feinstruktur, was bedeutet, dass sich die nukleare Bewegung solcher Systeme im Allgemeinen von derjenigen der vorherigen Kategorie unterscheidet. KW - vibrationally resolved electronic spectroscopy KW - photoelectron spectroscopy KW - resonance Raman spectroscopy KW - correlation function KW - ionization potential KW - time-dependent density functional theory KW - perylene KW - diamondoid KW - Schwingungsaufgelöste UV/VIS-Spektroskopie KW - Photoelektronenspektroskopie KW - Resonanz-Raman-Spektroskopie KW - Korrelationsfunktion KW - Ionisationspotential KW - Zeitabhängige Dichtefunktionaltheorie KW - Perylen KW - Diamondoide Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-418105 ER - TY - THES A1 - Xie, Zai-Lai T1 - Functional materials in metal-containing ionic liquids Y1 - 2012 CY - Potsdam ER - TY - THES A1 - Xie, Dongjiu T1 - Nanostructured Iron-based compounds as sulfur host material for lithium-sulfur batteries T1 - Nanostrukturierte Eisenverbindungen als Schwefel-Wirtsmaterial für Lithium-Schwefel-Batterien N2 - The present thesis focuses on the synthesis of nanostructured iron-based compounds by using β-FeOOH nanospindles and poly(ionic liquid)s (PILs) vesicles as hard and soft templates, respectively, to suppress the shuttle effect of lithium polysulfides (LiPSs) in Li-S batteries. Three types of composites with different nanostructures (mesoporous nanospindle, yolk-shell nanospindle, and nanocapsule) have been synthesized and applied as sulfur host material for Li-S batteries. Their interactions with LiPSs and effects on the electrochemical performance of Li-S batteries have been systematically studied. In the first part of the thesis, carbon-coated mesoporous Fe3O4 (C@M-Fe3O4) nanospindles have been synthesized to suppress the shuttle effect of LiPSs. First, β-FeOOH nanospindles have been synthesized via the hydrolysis of iron (III) chloride in aqueous solution and after silica coating and subsequent calcination, mesoporous Fe2O3 (M-Fe2O3) have been obtained inside the confined silica layer through pyrolysis of β-FeOOH. After the removal of the silica layer, electron tomography (ET) has been applied to rebuild the 3D structure of the M-Fe2O3 nanospindles. After coating a thin layer of polydopamine (PDA) as carbon source, the PDA-coated M-Fe2O3 particles have been calcinated to synthesize C@M-Fe3O4 nanospindles. With the chemisorption of Fe3O4 and confinement of mesoporous structure to anchor LiPSs, the composite C@M-Fe3O4/S electrode delivers a remaining capacity of 507.7 mAh g-1 at 1 C after 600 cycles. In the second part of the thesis, a series of iron-based compounds (Fe3O4, FeS2, and FeS) with the same yolk-shell nanospindle morphology have been synthesized, which allows for the direct comparison of the effects of compositions on the electrochemical performance of Li-S batteries. The Fe3O4-carbon yolk-shell nanospindles have been synthesized by using the β-FeOOH nanospindles as hard template. Afterwards, Fe3O4-carbon yolk-shell nanospindles have been used as precursors to obtain iron sulfides (FeS and FeS2)-carbon yolk-shell nanospindles through sulfidation at different temperatures. Using the three types of yolk-shell nanospindles as sulfur host, the effects of compositions on interactions with LiPSs and electrochemical performance in Li-S batteries have been systematically investigated and compared. Benefiting from the chemisorption and catalytic effect of FeS2 particles and the physical confinement of the carbon shell, the FeS2-C/S electrode exhibits the best electrochemical performance with an initial specific discharge capacity of 877.6 mAh g-1 at 0.5 C and a retention ratio of 86.7% after 350 cycles. In the third part, PILs vesicles have been used as soft template to synthesize carbon nanocapsules embedded with iron nitride particles to immobilize and catalyze LiPSs in Li-S batteries. First, 3-n-decyl-1-vinylimidazolium bromide has been used as monomer to synthesize PILs nanovesicles by free radical polymerization. Assisted by PDA coating route and ion exchange, PIL nanovesicles have been successfully applied as soft template in morphology-maintaining carbonization to prepare carbon nanocapsules embedded with iron nitride nanoparticles (FexN@C). The well-dispersed iron nitride nanoparticles effectively catalyze the conversion of LiPSs to Li2S, owing to their high electrical conductivity and strong chemical binding to LiPSs. The constructed FexN@C/S cathode demonstrates a high initial discharge capacity of 1085.0 mAh g-1 at 0.5 C with a remaining value of 930.0 mAh g-1 after 200 cycles. The results in the present thesis demonstrate the facile synthetic routes of nanostructured iron-based compounds with controllable morphologies and compositions using soft and hard colloidal templates, which can be applied as sulfur host to suppress the shuttle behavior of LiPSs. The synthesis approaches developed in this thesis are also applicable to fabricating other transition metal-based compounds with porous nanostructures for other applications. N2 - Die vorliegende Arbeit beschreibt die Synthese von nanostrukturierten Verbindungen auf Eisenbasis unter Verwendung von β-FeOOH-Nanospindeln und Vesikeln aus Poly(ionischen Flüssigkeiten) (PILs) als harte bzw. weiche Vorlagen, um den Shuttle-Effekt von Lithiumpolysulfiden (LiPSs) in Li-S-Batterien zu unterdrücken. Drei Arten von Verbundstoffen mit unterschiedlichen Nanostrukturen (mesoporöse Nanospindel, Dotterschalen-Nanospindel und Nanokapsel) wurden synthetisiert und als Schwefel-Wirtsmaterial für Li-S-Batterien eingesetzt. Ihre Wechselwirkungen mit LiPS und ihre Auswirkungen auf die elektrochemische Leistung von Li-S-Batterien wurden systematisch untersucht. Im ersten Teil der Arbeit wurden kohlenstoffbeschichtete mesoporöse Fe3O4 (C@M-Fe3O4) Nanospindeln synthetisiert, um den Shuttle-Effekt von LiPSs zu unterdrücken. Zunächst wurden β-FeOOH-Nanospindeln durch Hydrolyse von Eisen(III)-chlorid in wässriger Lösung synthetisiert. Nach der Beschichtung mit Siliziumdioxid und anschließender Kalzinierung wurde mesoporöses Fe2O3 (M-Fe2O3) innerhalb der begrenzten Siliziumdioxidschicht durch Pyrolyse von β-FeOOH erhalten. Nach der Entfernung der Siliziumdioxidschicht wurde Elektronentomographie (ET) eingesetzt, um die 3D-Struktur der M-Fe2O3-Nanospindeln zu rekonstruieren. Nach der Beschichtung mit einer dünnen Schicht Polydopamin (PDA) als Kohlenstoffquelle wurden die PDA-beschichteten M-Fe2O3-Partikel kalziniert, um C@M-Fe3O4-Nanospindeln zu synthetisieren. Durch die Chemisorption von Fe3O4 und die Einschließung der mesoporösen Struktur zur Verankerung der LiPSs liefert die zusammengesetzte C@M-Fe3O4/S-Elektrode nach 600 Zyklen eine Restkapazität von 507,7 mAh g-1 bei 1 C. Im zweiten Teil der Arbeit wurde eine Reihe von eisenbasierten Verbindungen (Fe3O4, FeS2, und FeS) mit der gleichen Dotterschalen-Nanospindel-Morphologie synthetisiert, was einen direkten Vergleich der Auswirkungen der Zusammensetzungen auf die elektrochemische Leistung von Li S-Batterien ermöglicht. Die Fe3O4-Kohlenstoff-Dotterschalen-Nanospindeln wurden unter Verwendung der β-FeOOH-Nanospindeln als harte Vorlage synthetisiert. Anschließend wurden Fe3O4-Kohlenstoff-Dotterschalen-Nanospindeln als Vorläufer verwendet, um Eisensulfide (FeS und FeS2) - Kohlenstoff-Dotterschalen-Nanospindeln durch Sulfidierung bei verschiedenen Temperaturen zu erhalten. Durch Verwendung der drei Arten von Dotterschalen-Nanospindeln als Schwefelwirt wurden die Auswirkungen der Zusammensetzungen auf die Wechselwirkungen mit LiPS und die elektrochemische Leistung in Li-S-Batterien systematisch untersucht und verglichen. Die FeS2-C/S-Elektrode, die von der Chemisorption und der katalytischen Wirkung der FeS2-Teilchen und dem physikalischen Einschluss der Kohlenstoffschale profitiert, zeigt die beste elektrochemische Leistung mit einer anfänglichen spezifischen Entladekapazität von 877,6 mAh g-1 bei 0,5 C und einem Kapazitätserhalt von 86,7 % nach 350 Zyklen. Im dritten Teil wurden PILs-Vesikel als weiche Vorlage verwendet, um Kohlenstoff-Nanokapseln zu synthetisieren, die mit Eisennitridpartikeln durchsetzt sind, um LiPSs in Li-S-Batterien zu immobilisieren und deren Umwandlung zu katalysieren. Zunächst wurde 3-n-Decyl-1-Vinylimidazoliumbromid als Monomer für die Synthese von PIL-Nanovesikeln durch radikalische Polymerisation verwendet. Mit Hilfe der PDA-Beschichtung und des Ionenaustauschs wurden die PIL-Nanomoleküle erfolgreich als weiche Vorlage bei der morphologieerhaltenden Karbonisierung eingesetzt, um Kohlenstoff-Nanokapseln mit eingebetteten Eisennitrid-Nanopartikeln (FexN@C) herzustellen. Die gut dispergierten Eisennitrid-Nanopartikel katalysieren die Umwandlung von LiPS in Li2S aufgrund ihrer hohen elektrischen Leitfähigkeit und starken chemischen Bindung an LiPS effektiv. Die konstruierte FexN@C/S-Kathode zeigt eine hohe anfängliche Entladekapazität von 1085,0 mAh g-1 bei 0,5 C mit einer verbleibenden Kapazität von 930,0 mAh g-1 nach 200 Zyklen. Die Ergebnisse dieser Arbeit zeigen, dass sich nanostrukturierte eisenbasierte Verbindungen mit kontrollierbarer Morphologie und Zusammensetzung leicht synthetisieren lassen, indem weiche und harte kolloidale Template verwendet werden, die als Schwefelwirt eingesetzt werden können, um das Shuttle-Verhalten von LiPS zu unterdrücken. Die in dieser Arbeit entwickelten Syntheseansätze sind auch für die Herstellung anderer Verbindungen auf Übergangsmetallbasis mit porösen Nanostrukturen für andere Anwendungen einsetzbar. KW - sulfur host KW - Schwefelwirt KW - Li-S batteries KW - Li-S-Batterien KW - iron-based compounds KW - Verbindungen auf Eisenbasis KW - nanospindles KW - Nanospindeln KW - vesicles KW - Vesikel KW - nanocapsules KW - Nanokapseln KW - poly(ionic liquid)s KW - poly(ionische Flüssigkeiten) KW - electron tomography KW - Elektronentomographie KW - cryo-electron microscopy KW - Kryo-Elektronenmikroskopie Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-610369 ER - TY - THES A1 - Wünsche, Matthias T1 - Die Gewinnung von Nickel und Vanadium aus Rückständen der petrolchemischen Industrie Y1 - 1993 ER - TY - THES A1 - Wu, Yuling T1 - Syntheses of defined carbohydrate surfactants and determination of their wetting behaviour under equilibrium and dynamic conditions Y1 - 1998 ER - TY - THES A1 - Won, Jooyoung T1 - Dynamic and equilibrium adsorption behaviour of ß-lactoglobulin at the solution/tetradecane interface: Effect of solution concentration, pH and ionic strength T1 - Dynamik und Gleichgewicht der Adsorption von ß-Lactoglobulin an der Grenzfläche Lösung / Tetradecan (W/TD) N2 - Proteins are amphiphilic and adsorb at liquid interfaces. Therefore, they can be efficient stabilizers of foams and emulsions. β-lactoglobulin (BLG) is one of the most widely studied proteins due to its major industrial applications, in particular in food technology. In the present work, the influence of different bulk concentration, solution pH and ionic strength on the dynamic and equilibrium pressures of BLG adsorbed layers at the solution/tetradecane (W/TD) interface has been investigated. Dynamic interfacial pressure (Π) and interfacial dilational elastic modulus (E’) of BLG solutions for various concentrations at three different pH values of 3, 5 and 7 at a fixed ionic strength of 10 mM and for a selected fixed concentration at three different ionic strengths of 1 mM, 10 mM and 100 mM are measured by Profile Analysis Tensiometer PAT-1 (SINTERFACE Technologies, Germany). A quantitative data analysis requires additional consideration of depletion due to BLG adsorption at the interface at low protein bulk concentrations. This fact makes experiments more efficient when oil drops are studied in the aqueous protein solutions rather than solution drops formed in oil. On the basis of obtained experimental data, concentration dependencies and the effect of solution pH on the protein surface activity was qualitatively analysed. In the presence of 10 mM buffer, we observed that generally the adsorbed amount is increasing with increasing BLG bulk concentration for all three pH values. The adsorption kinetics at pH 5 result in the highest Π values at any time of adsorption while it exhibits a less active behaviour at pH 3. Since the experimental data have not been in a good agreement with the classical diffusion controlled model due to the conformational changes which occur when the protein molecules get in contact with the hydrophobic oil phase in order to adapt to the interfacial environment, a new theoretical model is proposed here. The adsorption kinetics data were analysed with the newly proposed model, which is the classical diffusion model but modified by assuming an additional change in the surface activity of BLG molecules when adsorbing at the interface. This effect can be expressed through the adsorption activity constant in the corresponding equation of state. The dilational visco-elasticity of the BLG adsorbed interfacial layers is determined from measured dynamic interfacial tensions during sinusoidal drop area variations. The interfacial tension responses to these harmonic drop oscillations are interpreted with the same thermodynamic model which is used for the corresponding adsorption isotherm. At a selected BLG concentration of 2×10-6 mol/l, the influence of the ionic strength using different buffer concentration of 1, 10 and 100 mM on the interfacial pressure was studied. It is affected weakly at pH 5, whereas it has a strong impact by increasing buffer concentration at pH 3 and 7. In conclusion, the structure formation of BLG adsorbed layer in the early stage of adsorption at the W/TD interface is similar to those of the solution/air (W/A) surface. However, the equation of state at the W/TD interface provides an adsorption activity constant which is almost two orders of magnitude higher than that for the solution/air surface. At the end of this work, a new experimental tool called Drop and Bubble Micro Manipulator DBMM (SINTERFACE Technologies, Germany) has been introduced to study the stability of protein covered bubbles against coalescence. Among the available protocols the lifetime between the moment of contact and coalescence of two contacting bubble is determined for different BLG concentrations. The adsorbed amount of BLG is determined as a function of time and concentration and correlates with the observed coalescence behaviour of the contacting bubbles. N2 - Die vorliegende Arbeit ist ein Beitrag zum Verständnis des Überganges von der qualitativen zur quantitativen Beschreibung der Adsorption von Proteinen an der Wasser/Öl- Grenzfläche. Dabei wird die Adsorption des Molkeproteins ß-Lactoglobulin (BLG) an der Wasser/Tetradekan (W/TD) Grenzfläche untersucht. Die Proteinadsorption an Grenzflächen zwischen zwei nicht mischbaren Flüssigkeiten ist ein Zeitprozess. Die Tropfenprofil-Analysen-Tensiometrie (PAT) hat sich als optimale Methode erwiesen, um den Prozess der Bildung von Proteinadsorptionsschichten an Flüssig-/flüssig-Grenzflächen quantitativ zu untersuchen. Die gemessenen dynamischen Grenzflächenspannungen können genutzt werden, um die adsorbierte Menge von Protein an Grenzflächen zu bestimmen. Zusätzlich erlaubt die Methode, durch periodische Tropfenoszillationen, die Messung der Dilatations-Viskoelastizität. Die experimentellen Ergebnisse zeigen deutlich, dass die Adsorption von Proteinen mit der Konzentration ansteigt. Der Adsorptionsprozess von Proteinen ist ähnlich dem von Tensiden, allerdings wird seine Beschreibung wesentlich komplizierter, durch die zusätzliche Möglichkeit der Konformationsänderungen der Proteinmoleküle an der Grenzfläche. Ein kürzlich im Rahmen dieser Dissertation entwickeltes Modell zur Adsorptionskinetik von Proteinen wurde genutzt, um experimentelle Daten für BLG zu interpretieren. Dieses kinetische Modell erlaubt es, den Mechanismus der Proteinadsorption an der Wasser/Öl-Grenzfläche zu beschreiben, was durch ältere Modelle bisher nicht möglich war. Im neu entwickelten Modell wurde die klassische Diffusionstheorie so modifiziert, dass eine Änderung der Adsorptionsaktivität der adsorbierenden Proteinmoleküle berücksichtigt wird. Die Änderung der Adsorptionsaktivität geschieht durch den Kontakt adsorbierter BLG-Moleküle an der Wasser/Öl-Grenzfläche. Es wird nach diesem neuen Modell angenommen, dass die Adsorptionsaktivität eine Funktion der Adsorptionszeit ist. Die ansteigende Adsorptionaktivität ist erforderlich, um den Adsorptionsprozess von BLG über den gesamten Zeitbereich quantitativ zu beschrieben. Mit diesem neuen Modell wurde es möglich, die experimentellen Daten zur Adsorptionskinetik sowie zur Dilatationsrheologie von Adsorptionsschichten bei unterschiedlichen BLG-Konzentrationen, pH-Werten und Ionenstärken an der Grenzfläche Lösung/Tetradekan quantitativ zu beschreiben. Die Ergebnisse dienen als Ausgangspunkt für weitere Entwicklungen zur Verbesserung des Verständnisses der Stabilität von Schäumen und Emulsionen, die durch die Dynamik der Adsorption von Molekülen wie BLG signifikant beeinflusst wird. KW - beta-lactoglobulin KW - water/tetradecane interface KW - drop profile analysis tensiometry KW - dynamic interfacial tensions KW - protein adsorption KW - pH effect KW - ionic strength effect KW - protein stabilized foams KW - drop and bubble coalescence KW - interfacial dynamics KW - capillary pressure tensiometry KW - drop-drop interaction KW - bubble-bubble interaction KW - ß-Lactoglobulin KW - Flüssig-/flüssig-Grenzflächen KW - Wasser/Öl-Grenzfläche KW - Grenzfläche Lösung/Tetradecan KW - Dynamik der Adsorption KW - Gleichgewicht der Adsorption KW - Proteinadsorption KW - Tropfenprofil-Analysen-Tensiometrie KW - Tropfenoszillationen KW - Dilatations-Viskoelastizität KW - klassische Diffusionstheorie KW - Konformationsänderungen KW - Adsorptionsaktivität KW - Wirkung des pH-Werten KW - Wirkung des Ionenstärken KW - Stabilität von Schäumen KW - Stabilität von Emulsionen Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-99167 ER - TY - THES A1 - Woller, Jochen T1 - Synthesen und Reaktionen von Cycloalkylidenmalonsäurederivaten Y1 - 1995 ER - TY - THES A1 - Wolf, Gunter T1 - Diffusionsuntersuchungen an (polymer-modifizierten) Mikroemulsionen mittels Feldgradientenimpuls-NMR-Spektroskopie T1 - Diffusion studies in (polymer-modified) microemulsions using pulsed field gradient NMR spectroscopy N2 - Aufgrund des großen Verhältnisses von Oberfläche zu Volumen zeigen Nanopartikel interessante, größenabhängige Eigenschaften, die man im ausgedehnten Festkörper nicht beobachtet. Sie sind daher von großem wissenschaftlichem und technologischem Interesse. Die Herstellung kleinster Partikel ist aus diesem Grund überaus wünschenswert. Dieses Ziel kann mit Hilfe von Mikroemulsionen als Templatphasen bei der Herstellung von Nanopartikeln erreicht werden. Mikroemulsionen sind thermodynamisch stabile, transparente und isotrope Mischungen von Wasser und Öl, die durch einen Emulgator stabilisiert sind. Sie können eine Vielzahl verschiedener Mikrostrukturen bilden. Die Kenntnis der einer Mikroemulsion zugrunde liegenden Struktur und Dynamik ist daher von außerordentlicher Bedeutung, um ein gewähltes System potentiell als Templatphase zur Nanopartikelherstellung einsetzen zu können. In der vorliegenden Arbeit wurden komplexe Mehrkomponentensysteme auf der Basis einer natürlich vorkommenden Sojabohnenlecithin-Mischung, eines gereinigten Lecithins und eines Sulfobetains als Emulgatoren mit Hilfe der diffusionsgewichteten 1H-NMR-Spektroskopie unter Verwendung gepulster Feldgradienten (PFG) in Abhängigkeit des Zusatzes des Polykations Poly-(diallyl-dimethyl-ammoniumchlorid) (PDADMAC) untersucht. Der zentrale Gegenstand dieser Untersuchungen war die strukturelle und dynamische Charakterisierung der verwendeten Mikroemulsionen hinsichtlich ihrer potentiellen Anwendbarkeit als Templatphasen für die Herstellung möglichst kleiner Nanopartikel. Die konzentrations- und zeit-abhängige NMR-Diffusionsmessung stellte sich dabei als hervorragend geeignete und genaue Methode zur Untersuchung der Mikrostruktur und Dynamik in den vorliegenden Systemen heraus. Die beobachtete geschlossene Wasser-in-Öl- (W/O-) Mikrostruktur der Mikroemulsionen zeigt deutlich deren potentielle Anwendbarkeit in der Nanopartikelsynthese. Das Gesamtdiffusionsverhalten des Tensides wird durch variierende Anteile aus der Verschiebung gesamter Aggregate, der Monomerdiffusion im Medium bzw. der medium-vermittelten Oberflächendiffusion bestimmt. Dies resultierte in einigen Fällen in einer anormalen Diffusionscharakteristik. In allen Systemen liegen hydrodynamische und direkte Wechselwirkungen zwischen den Tensidaggregaten vor. Der Zusatz von PDADMAC zu den Mikroemulsionen resultiert in einer Stabilisierung der flüssigen Grenzfläche der Tensidaggregate aufgrund der Adsorption des Polykations auf den entgegengesetzt geladenen Tensidfilm und kann potentiell zu Nanopartikeln mit kleineren Dimensionen und schmaleren Größenverteilungen führen. N2 - Owing to their large surface-to-volume ratio nanoparticles show interesting size-dependent properties that are not observable in bulk materials. Thus, they are of great scientific and technological interest. Thereby, the highly desirable preparation of as small particles as possible might be easily achieved using microemulsions as template phases. Microemulsions are thermodynamically stable, transparent and isotropic mixtures of water and oil stabilized by an emulsifying agent. However, microemulsions may form a great variety of different microstructures. Thus, it is of utmost importance to know the underlying microstructure and microdynamics of a chosen microemulsion system in order to use it as a template phase for nanoparticle formation. In the present study complex multi-component microemulsion systems based on a naturally occurring soybean lecithin mixture, purified lecithin and sulfobetaine as emulsifiers were investigated by diffusion-weighted pulsed field gradient (PFG) 1H NMR spectroscopy in the presence and absence of the polycation poly-(diallyldimethylammonium chloride) (PDADMAC). The central topic of this study was to structurally and dynamically characterize the present microemulsions with respect to their potential use in nanoparticle formation. The concentration- and time-dependent NMR diffusion measurements turned out to be a suitable and accurate tool to investigate the microstructure and microdynamics of the systems under investigation. They reveal closed water-in-oil (W/O) microemulsion microstructures which prove the potential suitability of the respective systems as template phases for the preparation of nano-sized particles. The overall diffusion behavior of surfactants were found to be governed by varying contributions from displacements of entire aggregates, monomer diffusion in the medium and bulk-mediated surface diffusion, respectively. In some cases this led to a marked anomalous diffusion characteristics. In all systems interactions between aggregates are dominated by hydrodynamic and direct forces. The addition of PDADMAC to the microemulsion systems results in a stabilization of the liquid interface of surfactant aggregates due to the adsorption of the polycation at the oppositely charged surfactant film and may potentially lead to nanoparticles of smaller dimensions and narrower size distributions. KW - Mikroemulsion KW - Mikrostruktur KW - Magnetische Kernresonanz KW - PFG-NMR-Spektroskopie KW - Selbstdiffusion KW - Anomale Diffusion KW - Polykation KW - Inverse Micelle KW - Wasser-in-Öl-Mikroemulsion KW - Tensiddynamik KW - medium-vermittelte Oberflächendiffusion KW - Levy-Bewegung KW - water-in-oil microemulsion KW - surfactant dynamics KW - bulk-mediated surface diffusion KW - Levy walk Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-6259 ER - TY - THES A1 - Wolf, Felix T1 - Neuartige Olefine und Aryldiazoniumtetrafluoroborate für die MATSUDA-HECK-Reaktion Y1 - 2016 ER - TY - THES A1 - Wohlrab, Erdmann Sebastian T1 - Polymerinduzierte Morphogenese bei der Kristalisation von Aminosäuren Y1 - 2003 ER - TY - THES A1 - Wohlgemuth, Stephanie-Angelika T1 - Functional nanostructured hydrothermal carbons for sustainable technologies : heteroatom doping and superheated vapor T1 - Funktionelle, Nanostrukturierte Hydrothermal-Kohlenstoffe für Nachhaltige Technnologien: Heteroatom-Dotierung und Überkritischer Dampf N2 - The underlying motivation for the work carried out for this thesis was the growing need for more sustainable technologies. The aim was to synthesize a “palette” of functional nanomaterials using the established technique of hydrothermal carbonization (HTC). The incredible diversity of HTC was demonstrated together with small but steady advances in how HTC can be manipulated to tailor material properties for specific applications. Two main strategies were used to modify the materials obtained by HTC of glucose, a model precursor representing biomass. The first approach was the introduction of heteroatoms, or “doping” of the carbon framework. Sulfur was for the first time introduced as a dopant in hydrothermal carbon. The synthesis of sulfur and sulfur/nitrogen doped microspheres was presented whereby it was shown that the binding state of sulfur could be influenced by varying the type of sulfur source. Pyrolysis may additionally be used to tune the heteroatom binding states which move to more stable motifs with increasing pyrolysis temperature. Importantly, the presence of aromatic binding states in the as synthesized hydrothermal carbon allows for higher heteroatom retention levels after pyrolysis and hence more efficient use of dopant sources. In this regard, HTC may be considered as an “intermediate” step in the formation of conductive heteroatom doped carbon. To assess the novel hydrothermal carbons in terms of their potential for electrochemical applications, materials with defined nano-architectures and high surface areas were synthesized via templated, as well as template-free routes. Sulfur and/or nitrogen doped carbon hollow spheres (CHS) were synthesized using a polystyrene hard templating approach and doped carbon aerogels (CA) were synthesized using either the albumin directed or borax-mediated hydrothermal carbonization of glucose. Electrochemical testing showed that S/N dual doped CHS and aerogels derived via the albumin approach exhibited superior catalytic performance compared to solely nitrogen or sulfur doped counterparts in the oxygen reduction reaction (ORR) relevant to fuel cells. Using the borax mediated aerogel formation, nitrogen content and surface area could be tuned and a carbon aerogel was engineered to maximize electrochemical performance. The obtained sample exhibited drastically improved current densities compared to a platinum catalyst (but lower onset potential), as well as excellent long term stability. In the second approach HTC was carried out at elevated temperatures (550 °C) and pressure (50 bar), corresponding to the superheated vapor regime (htHTC). It was demonstrated that the carbon materials obtained via htHTC are distinct from those obtained via ltHTC and subsequent pyrolysis at 550 °C. No difference in htHTC-derived material properties could be observed between pentoses and hexoses. The material obtained from a polysaccharide exhibited a slightly lower degree of carbonization but was otherwise similar to the monosaccharide derived samples. It was shown that in addition to thermally induced carbonization at 550 °C, the SHV environment exhibits a catalytic effect on the carbonization process. The resulting materials are chemically inert (i.e. they contain a negligible amount of reactive functional groups) and possess low surface area and electronic conductivity which distinguishes them from carbon obtained from pyrolysis. Compared to the materials presented in the previous chapters on chemical modifications of hydrothermal carbon, this makes them ill-suited candidates for electronic applications like lithium ion batteries or electrocatalysts. However, htHTC derived materials could be interesting for applications that require chemical inertness but do not require specific electronic properties. The final section of this thesis therefore revisited the latex hard templating approach to synthesize carbon hollow spheres using htHTC. However, by using htHTC it was possible to carry out template removal in situ because the second heating step at 550 °C was above the polystyrene latex decomposition temperature. Preliminary tests showed that the CHS could be dispersed in an aqueous polystyrene latex without monomer penetrating into the hollow sphere voids. This leaves the stagnant air inside the CHS intact which in turn is promising for their application in heat and sound insulating coatings. Overall the work carried out in this thesis represents a noteworthy development in demonstrating the great potential of sustainable carbon materials. N2 - Das Ziel der vorgelegten Arbeit war es, mit Hilfe der Hydrothermalen Carbonisierung (HTC) eine Palette an verschiedenen Materialien herzustellen, deren physikalische und chemische Eigenschaften auf spezifische Anwendungen zugeschnitten werden können. Die Motivation hierfür stellt die Notwendigkeit, Alternativen zu Materialien zu finden, die auf fossilen Brennstoffen basieren. Dabei stellen vor allem nachhaltige Energien eine der größten Herausforderungen der Zukunft dar. HTC ist ein mildes, nachhaltiges Syntheseverfahren welches prinzipiell die Nutzung von biologischen Rohstoffen (z. B. landwirtschaftlichen Abfallprodukten) für die Herstellung von wertvollen, Kohlenstoff-basierten Materialien erlaubt. Es wurden zwei verschiedene Ansätze verwendet, um hydrothermalen Kohlenstoff zu modifizieren. Zum einen wurde HTC unter „normalen“ Bedingungen ausgeführt, d. h. bei 180 °C und einem Druck von etwa 10 bar. Der Zucker Glukose diente in allen Fällen als Kohlenstoff Vorläufer. Durch Zugabe von stickstoff und /oder schwefelhaltigen Additiven konnte dotierte Hydrothermalkohle hergestellt werden. Dotierte Kohlenstoffe sind bereits für ihre positiven Eigenschaften, wie verbesserte Leitfähigkeit oder erhöhte Stabilität, bekannt. Zusätzlich zu Stickstoff dotierter Hydrothermalkohle, die bereits von anderen Gruppen hergestellt werden konnte, wurde in dieser Arbeit zum ersten Mal Schwefel in Hydrothermalkohle eingebaut. Außerdem wurden verschiedene Ansätze verwendet, um Oberfläche und definierte Morphologie der dotierten Materialien zu erzeugen, welche wichtig für elektrochemische Anwendungen sind. Schwefel- und/oder stickstoffdotierte Kohlenstoff Nanohohlkugeln sowie Kohlenstoff Aerogele konnten hergestellt werden. Mit Hilfe von einem zusätzlichen Pyrolyseschritt (d. h. Erhitzen unter Schutzgas) konnte die Leitfähigkeit der Materialien hergestellt werden, die daraufhin als Nichtmetall-Katalysatoren für Wasserstoff-Brennstoffzellen getestet wurden. Im zweiten Ansatz wurde HTC unter extremen Bedingungen ausgeführt, d. h. bei 550 °C und einem Druck von ca. 50 bar, welches im Wasser Phasendiagram dem Bereich des Heißdampfes entspricht. Es konnte gezeigt werden, dass die so erhaltene Hydrothermalkohle ungewöhnliche Eigenschaften besitzt. So hat die Hochtemperatur-Hydrothermalkohle zwar einen hohen Kohlenstoffgehalt (mehr als 90 Massenprozent), enthält aber auch viele Wasserstoffatome und ist dadurch schlecht leitfähig. Da damit elektrochemische Anwendungen so gut wie ausgeschlossen sind, wurde die Hochtemperatur-Hydrothermalkohle für Anwendungen vorgesehen, welche chemische Stabilität aber keine Leitfähigkeit voraussetzen. So wurden beispielsweise Hochtemperatur-Kohlenstoff-Nanohohlkugeln synthetisiert, die großes Potential als schall- und wärmeisolierende Additive für Beschichtungen darstellen. Insgesamt konnten erfolgreich verschiedenste Materialien mit Hilfe von HTC hergestellt werden. Es ist zu erwarten, dass sie in Zukunft zu nachhaltigen Technologien und damit zu einem weiteren Schritt weg von fossilen Brennstoffen beitragen werden. KW - Hydrothermale Karbonisierung KW - Heteroatom-Dotierung KW - Aerogele KW - Hohlkugeln KW - Elektrokatalyse KW - Hydrothermal Carbonization KW - Heteroatom Doping KW - Aerogels KW - Hollow Spheres KW - Electrocatalysis Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-60120 ER - TY - THES A1 - Witt, Barbara T1 - Toxicological characterization of lipid-soluble arsenic species in human brain cells Y1 - 2017 ER - TY - THES A1 - Wirth, Jonas A. T1 - Chemische Reaktionen in Substrat-Adsorbat-Systemen BT - eine kinetische Perspektive Y1 - 2014 ER - TY - THES A1 - Winter, Alette T1 - Tetrahalidocuprat(II)-komplexe : Untersuchungen zur Relation von Struktur- und EPR-Parametern Y1 - 2013 CY - Potsdam ER - TY - THES A1 - Winkler, Henning T1 - Synthese von thermoplastisch verarbeitbaren Fettsäure-Acylderivaten der Stärke und Proteine T1 - Synthesis of thermoplastic processable fatty acid acyl derivatives of starch and proteins N2 - In den vergangenen Jahren wurden stetig wachsende Produktionskapazitäten von Biokunststoffen aus nachwachsenden Rohstoffe nverzeichnet. Trotz großer Produktionskapazitäten und einem geeigneten Eigenschaftsprofil findet Stärke nur als hydrophile, mit Weichmachern verarbeitete thermoplastische Stärke (TPS) in Form von Blends mit z. B. Polyestern Anwendung. Gleiches gilt für Kunststoffe auf Proteinbasis. Die vorliegende Arbeit hat die Entwicklung von Biokunststoffen auf Stärkebasis zum Ziel, welche ohne externe Weichmacher thermoplastisch verarbeitbar und hydrophob sind sowie ein mechanisches Eigenschaftsprofil aufweisen, welches ein Potenzial zur Herstellung von Materialien für eine Anwendung als Verpackungsmittel bietet. Um die Rohstoffbasis für Biokunststoffe zu erweitern, soll das erarbeitete Konzept auf zwei industriell verfügbare Proteintypen, Zein und Molkenproteinisolat (WPI), übertragen werden. Als geeignete Materialklasse wurden Fettsäureester der Stärke herausgearbeitet. Zunächst fand ein Vergleich der Säurechlorid-Veresterung und der Umesterung von Fettsäurevinylestern statt, woraus letztere als geeignetere Methode hervorging. Durch Variation der Reaktionsparameter konnte diese optimiert und auf eine Serie der Fettsäurevinylester von Butanoat bis Stearat für DS-Werte bis zu 2,2-2,6 angewandt werden. Möglich war somit eine systematische Studie unter Variation der veresterten Fettsäure sowie des Substitutionsgrades (DS). Sämtliche Produkte mit einem DS ab 1,5 wiesen eine ausgprägte Löslichkeit in organischen Lösungsmitteln auf wodurch sowohl die Aufnahme von NMR-Spektren als auch Molmassenbestimmung mittels Größenausschlusschromatographie mit gekoppelter Mehrwinkel-Laserlichtstreuung (GPC-MALLS) möglich waren. Durch dynamische Lichtstreuung (DLS) wurde das Löslichkeitsverhalten veranschaulicht. Sämtliche Produkte konnten zu Filmen verarbeitet werden, wobei Materialien mit DS 1,5-1,7 hohe Zugfestigkeiten (bis zu 42 MPa) und Elastizitätsmodule (bis 1390 MPa) aufwiesen. Insbesondere Stärkehexanoat mit DS <2 sowie Stärkebutanoat mit DS >2 hatten ein mechanisches Eigenschaftsprofil, welches insbesondere in Bezug auf die Festigkeit/Steifigkeit vergleichbar mit Verpackungsmaterialien wie Polyethylen war (Zugfestigkeit: 15-32 MPa, E-Modul: 300-1300 MPa). Zugfestigkeit und Elastizitätsmodul nahmen mit steigender Kettenlänge der veresterten Fettsäure ab. Ester längerkettiger Fettsäuren (C16-C18) waren spröde. Über Weitwinkel-Röntgenstreuung (WAXS) und Infrarotspektroskopie (ATR-FTIR) konnte der Verlauf der Festigkeiten mit einer zunehmenden Distanz der Stärke im Material begründet werden. Es konnten von DS und Kettenlänge abhängige Glasübergänge detektiert werden, die kristallinen Strukturen der langkettigen Fettsäuren zeigten einen Schmelzpeak. Die Hydrophobie der Filme wurde anhand von Kontaktwinkeln >95° gegen Wasser dargestellt. Blends mit biobasierten Polyterpenen sowie den in der Arbeit hergestellten Zein-Acylderivaten ermöglichten eine weitere Verbesserung der Zugfestigkeit bzw. des Elastizitätsmoduls hochsubstituierter Produkte. Eine thermoplastische Verarbeitung mittels Spritzgießen war sowohl für Produkte mit hohem als auch mittlerem DS-Wert ohne jeglichen Zusatz von Weichmachern möglich. Es entstanden homogene, transparente Prüfstäbe. Untersuchungen der Härte ergaben auch hier für Stärkehexanoat und –butanoat mit Polyethylen vergleichbare Werte. Ausgewählte Produkte wurden zu Fasern nach dem Schmelzspinnverfahren verarbeitet. Hierbei wurden insbesondere für hochsubstituierte Derivate homogenen Fasern erstellt, welche im Vergleich zur Gießfolie signifikant höhere Zugfestigkeiten aufwiesen. Stärkeester mit mittlerem DS ließen sich ebenfalls verarbeiten. Zunächst wurden für eine Übertragung des Konzeptes auf die Proteine Zein und WPI verschiedene Synthesemethoden verglichen. Die Veresterung mit Säurechloriden ergab hierbei die höchsten Werte. Im Hinblick auf eine gute Löslichkeit in organischen Lösungsmitteln wurde für WPI die Veresterung mit carbonyldiimidazol (CDI)-aktivierten Fettsäuren in DMSO und für Zein die Veresterung mit Säu-rechloriden in Pyridin bevorzugt. Es stellte sich heraus, dass acyliertes WPI zwar hydrophob, jedoch ohne Weichmacher nicht thermoplastisch verarbeitet werden konnte. Die Erstellung von Gießfolien führte zu Sprödbruchverhalten. Unter Zugabe der biobasierten Ölsäure wurde die Anwendung von acyliertem WPI als thermoplastischer Filler z. B. in Blends mit Stärkeestern dargestellt. Im Gegensatz hierzu zeigte acyliertes Zein Glasübergänge <100 °C bei ausreichender Stabilität (150-200 °C). Zeinoleat konnte ohne Weichmacher zu einer transparenten Gießfolie verarbeitet werden. Sämtliche Derivate erwiesen sich als ausgeprägt hydrophob. Zeinoleat konnte über das Schmelzspinnverfahren zu thermoplastischen Fasern verarbeitet werden. N2 - In recent years, a steadily growing production capacity of bioplastic based on renewable resources was noticed. Despite its huge production capacities and an appropriate property profile (ubiquitous occurrence, easy extraction), starch is only applied in addition of plasticizers in a hydrophilic, thermoplastic form in blends with e. g. polyesters. The same applies to bioplastics based on proteins. The actual study has the aim to develop starch-based bioplastics, which are hydrophobic, thermoplastic without the addition of any plasticizer and have mechanical properties to be a suitable alternative material in the area of food packaging. To obtain a variation of the raw materials for bioplastics, the concept shall be applied to two types of industrial available proteins, whey protein isolate (WPI) and Zein. Fatty acid esters of starch came out to be a suitable class of materials. Initially, the methods of esterifying acid chlorides and the transesterification of fatty acid vinyl esters were compared with the latter being more appropriate. Reaction parameters of this method were optimized and it was applied to a complete series of vinyl ester reagents (butanoate to stearate), leading to degree of substitution (DS)-values up to 2.2-2.6. With that, a systematic study of the variation of the fatty acid ester chain as well as the DS became possible. It came out that all products with a DS >1.5 showed a well-marked solubility in organic solvents, whereby solution NMR-studies as well as measurements of the molecular weight distributions by using size exclusion chroma-tography with multi-angle laser light scattering (SEC-MALLS) were possible. The different solution behavior was studied by dynamic light scattering (DLS). All soluble products could be formed into films via casting, where materials with a DS of 1.5-1.7 showed the highest values concerning tensile strength (up to 42 MPa) and Youngs modulus (up to 1390 MPa). Especially starch hexanoate with DS <2 and starch butanoate with a DS >2 revealed mechanical properties which are comparable to usually applied polymers for food packaging, e. g. polyethylene (tensile strength: 15-20 MPa, E-Mod: 300-1300 MPa). Tensile strength and Youngs modulus were reduced with increasing length of the esterified fatty acid. Wide-angle X-Ray scattering (WAXS) and infrared spectroscopy (ATR-FTIR) explained this tendency by an increasing intermolecular distance of the starch in the material. Glassy transitions of the materials were detected and showed a dependency on the type of esterified fatty acid and the DS. The crystalline structures of the esterified long-chain fatty acids revealed a melting peak. All films came out to be hydrophobic with contact angles against water >95°. The tensile strength and the Youngs modulus of the highly substituted products could be further improved by blending them with biobased polyterpenes as well as the acylated Zein. A thermoplastic processing without the use of any plasticizer additives was possible for products with a medium and high DS. Homogeneous, transparent testing specimens were obtained. The specific mechanical values were comparable with the casted films, although the highest values for the tensile strength and the elongation were lower. Investigations of the hardness showed comparable values to polyethylene. Selected samples were further processed to fibers by melt spinning. Especially starch esters with high DS revealed homogeneous fibers with a significant increase in the tensile strength compared to the film or testing specimen. Even fatty acid starch esters with a medium DS were processed by the melt-spinning, but their higher glassy transition lead to a reduced softening behavior. To transfer this concept to the class of proteins, different methods of synthesis were studied in the first step, which differed in their amount of acylation. The acylation using fatty acid chlorides lead to highest values. With regard to a well-marked organic solvent solubility, in the case of WPI the acylation with carbonyldiimidazol (CDI)-activated fatty acid was established. For Zein, the acid chloride acylation in pyridine gave the desired results. It came out the fatty acid acylated soluble WPI could not be thermoplastic processed without additional plasticizers. By using biobased oleic acid as additive, the potential of acylated WPI as a thermoplastic filler in blends with e. g. fatty acid esters of starch was shown. In contrast, fatty acid acyl derivatives of Zein revealed well marked glassy transitions <100 °C with an adequate thermal stability. While Zeinoleate could be formed into transparent films via solvent casting without any plasticizer additives, low amounts of tall oil enabled film-forming in the case of acyl derivatives with shorter fatty acids as well. All derivatives revealed a well-marked hydrophobicity. Finally, Zeinoleate was thermoplastically processed into fibers by melt-spinning without any further additives. KW - Stärke KW - Proteine KW - thermoplastisch KW - Gießfolien KW - Fasern KW - starch KW - proteins KW - thermoplastic KW - films KW - casted-films KW - fibres Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-71089 ER - TY - THES A1 - Willert, Mirjam A. T1 - Prinzipien und Anwendungsmöglichkeiten nichtwäßriger und inverser Miniemulsionen Y1 - 2001 SN - 3-89873-329-7 PB - Cuvillier CY - Göttingen ER - TY - THES A1 - Willersinn, Jochen T1 - Self-Assembly of double hydrophilic block copolymers T1 - Selbstorganisation Doppelt Hydrophiler Blockcopolymere BT - organized particles and vesicles beyond amphiphiles BT - organisierte Partikel und Vesikel jenseits von Amphiphilen N2 - The motivation of this work was to investigate the self-assembly of a block copolymer species that attended little attraction before, double hydrophilic block copolymers (DHBCs). DHBCs consist of two linear hydrophilic polymer blocks. The self-assembly of DHBCs towards suprastructures such as particles and vesicles is determined via a strong difference in hydrophilicity between the corresponding blocks leading to a microphase separation due to immiscibility. The benefits of DHBCs and the corresponding particles and vesicles, such as biocompatibility, high permeability towards water and hydrophilic compounds as well as the large amount of possible functionalizations that can be addressed to the block copolymers make the application of DHBC based structures a viable choice in biomedicine. In order to assess a route towards self-assembled structures from DHBCs that display the potential to act as cargos for future applications, several block copolymers containing two hydrophilic polymer blocks were synthesized. Poly(ethylene oxide)-b-poly(N-vinylpyrrolidone) (PEO-b-PVP) and Poly(ethylene oxide)-b-poly(N-vinylpyrrolidone-co-N-vinylimidazole) (PEO-b-P(VP-co-VIm) block copolymers were synthesized via reversible deactivation radical polymerization (RDRP) techniques starting from a PEO-macro chain transfer agent. The block copolymers displayed a concentration dependent self-assembly behavior in water which was determined via dynamic light scattering (DLS). It was possible to observe spherical particles via laser scanning confocal microscopy (LSCM) and cryogenic scanning electron microscopy (cryo SEM) at highly concentrated solutions of PEO-b-PVP. Furthermore, a crosslinking strategy with (PEO-b-P(VP-co-VIm) was developed applying a diiodo derived crosslinker diethylene glycol bis(2-iodoethyl) ether to form quaternary amines at the VIm units. The formed crosslinked structures proved stability upon dilution and transfer into organic solvents. Moreover, self-assembly and crosslinking in DMF proved to be more advantageous and the crosslinked structures could be successfully transferred to aqueous solution. The afforded spherical submicron particles could be visualized via LSCM, cryo SEM and Cryo TEM. Double hydrophilic pullulan-b-poly(acrylamide) block copolymers were synthesized via copper catalyzed alkyne azide cycloaddition (CuAAC) starting from suitable pullulan alkyne and azide functionalized poly(N,N-dimethylacrylamide) (PDMA) and poly(N-ethylacrylamide) (PEA) homopolymers. The conjugation reaction was confirmed via SEC and 1H-NMR measurements. The self-assembly of the block copolymers was monitored with DLS and static light scattering (SLS) measurements indicating the presence of hollow spherical structures. Cryo SEM measurements could confirm the presence of vesicular structures for Pull-b-PEA block copolymers. Solutions of Pull-b-PDMA displayed particles in cryo SEM. Moreover, an end group functionalization of Pull-b-PDMA with Rhodamine B allowed assessing the structure via LSCM and hollow spherical structures were observed indicating the presence of vesicles, too. An exemplified pathway towards a DHBC based drug delivery vehicle was demonstrated with the block copolymer Pull-b-PVP. The block copolymer was synthesized via RAFT/MADIX techniques starting from a pullulan chain transfer agent. Pull-b-PVP displayed a concentration dependent self-assembly in water with an efficiency superior to the PEO-b-PVP system, which could be observed via DLS. Cryo SEM and LSCM microscopy displayed the presence of spherical structures. In order to apply a reversible crosslinking strategy on the synthesized block copolymer, the pullulan block was selectively oxidized to dialdehydes with NaIO4. The oxidation of the block copolymer was confirmed via SEC and 1H-NMR measurements. The self-assembled and oxidized structures were subsequently crosslinked with cystamine dihiydrochloride, a pH and redox responsive crosslinker resulting in crosslinked vesicles which were observed via cryo SEM. The vesicular structures of crosslinked Pull-b-PVP could be disassembled by acid treatment or the application of the redox agent tris(2-carboxyethyl)-phosphin-hydrochloride. The successful disassembly was monitored with DLS measurements. To conclude, self-assembled structures from DHBCs such as particles and vesicles display a strong potential to generate an impact on biomedicine and nanotechnologies. The variety of DHBC compositions and functionalities are very promising features for future applications. N2 - Die Selbstanordnung von amphiphilen Blockcopolymeren in Wasser zu Strukturen höherer Ordnung, wie Partikel oder Vesikel, ist seit vielen Jahren bekannt und findet Anwendung in vielen Aspekten der Medizin und Materialwissenschaft. Allerdings ist die treibende Kraft dieser Selbstanordnung zu Vesikeln, die Hydrophobie des wasserunlöslichen Polmyerblocks, auch ein Hindernis für den gezielten Transport von neuen Medikamenten und Wirkstoffen, da die Membran dieser Vesikel aufgrund des hydrophoben Anteils sehr dicht gepackt ist und eine Diffusion der Wirkstoffe durch diese Membran häufig nur durch hohen synthetischen Aufwand gewährleistet werden kann. Einen möglichen Ausweg bietet die Anwendung von doppelt hydrophilen Blockcopolymeren (DHBCs), respektive Blockcopolymere die aus zwei Polymerblöcken mit unterschiedlicher Hydrophilie bestehen. Ist dieser Unterschied groß genug, können DHBCs Partikel- und Vesikelstrukturen ausbilden, die denen der amphiphilen Blockcopolymere ähnlich sind. Um das Potential von DHBC Strukturen zu untersuchen und einen tieferen Einblick in die fundamentalen Prinzipien dieser Selbstanordnung zu erhalten, wurden in dieser Arbeit fünf verschiedene Blockcopolymere hergestellt. Poly(Ethylenoxid)-b-Poly(N-Vinylpyrrolidon) und Poly(Ethylenoxid)-b-Poly(N-Vinylpyrrolidon-co-N-Vinylimidazol) Blockcopolymere wurden über eine kontrollierte radikalische Polymerisation hergestellt und zeigten eine konzentrationsabhängige Selbstanordnung zu Partikeln mit Größen unter einem Mikrometer. Diese Partikel konnten vernetzt werden, sodass sie auch bei starker Verdünnung nicht zerfallen. Zwei Pullulan-b-Poly(Acrylamid) Blockcopolymere wurden über eine Konjugationsreaktion hergestellt, die die beiden separaten Polymerblöcke miteinander verbindet. Diese Blockcopolymere ordneten sich in Wasser zu Vesikulären Strukturen mit Größen zwischen 250 nm und 500 nm. Des Weiteren war es möglich, einen Farbstoff an ein Blockcopolymer anzubringen und den vesikulären Charakter mit konfokaler Mikroskopie zu untersuchen. Ein Ausblick auf mögliche medizinische Anwendung von DHBCs wurde mit dem letzten Blockcopolymer Pullulan-b-Poly(N-Vinylpyrrolidon) gegeben. Vesikel aus diesem Blockcopolymer wurden mit einem pH- und Redox-responsivem Vernetzer vernetzt und es wurde gezeigt, dass sich die vesikulären Strukturen durch Säurebehandlung zersetzen lassen. Dieses System veranschaulicht die theoretische Anwendungsmöglichkeit von DHBCs im gezielten Medikamententransport. KW - self-assembly KW - double hydrophilic block copolymers KW - polymer chemistry KW - RAFT/MADIX polymerization KW - block copolymer vesicles KW - Selbstorganisation KW - Doppelt hydrophile Blockcopolymere KW - Polymerchemie KW - RAFT/MADIX Polymerisation KW - Blockcopolymervesikel Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-408578 ER - TY - THES A1 - Wilken, Ralph T1 - Untersuchungen zur Oberflächenmodifizierung ausgewählter Modellpolymere durch VUV-Photolyse Y1 - 1998 ER - TY - THES A1 - Wilke, Antje T1 - Synthese und Charakterisierung von mesoporösen Polymernetzwerken Y1 - 2012 CY - Potsdam ER - TY - THES A1 - Werner, Peter T1 - Untersuchung stark-streuender Polymersuspensionen mittels optischer Methoden Y1 - 2018 ER - TY - THES A1 - Weißenberger, Markus Christian T1 - Nanocasting : eine Methode zum gezielten Aufbau strukturierter Materie Y1 - 1997 CY - Teltow ER - TY - THES A1 - Weiß, Jan T1 - Synthesis and self-assembly of multiple thermoresponsive amphiphilic block copolymers T1 - Synthese und Selbstorganisation von mehrfach thermisch schaltbaren amphiphilen Blockcopolymeren N2 - In the present thesis, the self-assembly of multi thermoresponsive block copolymers in dilute aqueous solution was investigated by a combination of turbidimetry, dynamic light scattering, TEM measurements, NMR as well as fluorescence spectroscopy. The successive conversion of such block copolymers from a hydrophilic into a hydrophobic state includes intermediate amphiphilic states with a variable hydrophilic-to-lipophilic balance. As a result, the self-organization is not following an all-or-none principle but a multistep aggregation in dilute solution was observed. The synthesis of double thermoresponsive diblock copolymers as well as triple thermoresponsive triblock copolymers was realized using twofold-TMS labeled RAFT agents which provide direct information about the average molar mass as well as residual end group functionality from a routine proton NMR spectrum. First a set of double thermosensitive diblock copolymers poly(N-n-propylacrylamide)-b-poly(N-ethylacrylamide) was synthesized which differed only in the relative size of the two blocks. Depending on the relative block lengths, different aggregation pathways were found. Furthermore, the complementary TMS-labeled end groups served as NMR-probes for the self-assembly of these diblock copolymers in dilute solution. Reversible, temperature sensitive peak splitting of the TMS-signals in NMR spectroscopy was indicative for the formation of mixed star-/flower-like micelles in some cases. Moreover, triple thermoresponsive triblock copolymers from poly(N-n-propylacrylamide) (A), poly(methoxydiethylene glycol acrylate) (B) and poly(N-ethylacrylamide) (C) were obtained from sequential RAFT polymerization in all possible block sequences (ABC, BAC, ACB). Their self-organization behavior in dilute aqueous solution was found to be rather complex and dependent on the positioning of the different blocks within the terpolymers. Especially the localization of the low-LCST block (A) had a large influence on the aggregation behavior. Above the first cloud point, aggregates were only observed when the A block was located at one terminus. Once placed in the middle, unimolecular micelles were observed which showed aggregation only above the second phase transition temperature of the B block. Carrier abilities of such triple thermosensitive triblock copolymers tested in fluorescence spectroscopy, using the solvatochromic dye Nile Red, suggested that the hydrophobic probe is less efficiently incorporated by the polymer with the BAC sequence as compared to ABC or ACB polymers above the first phase transition temperature. In addition, due to the problem of increasing loss of end group functionality during the subsequent polymerization steps, a novel concept for the one-step synthesis of multi thermoresponsive block copolymers was developed. This allowed to synthesize double thermoresponsive di- and triblock copolymers in a single polymerization step. The copolymerization of different N-substituted maleimides with a thermosensitive styrene derivative (4-vinylbenzyl methoxytetrakis(oxyethylene) ether) led to alternating copolymers with variable LCST. Consequently, an excess of this styrene-based monomer allowed the synthesis of double thermoresponsive tapered block copolymers in a single polymerization step. N2 - Die Selbstorganisation von mehrfach thermisch schaltbaren Blockcopolymeren in verdünnter wässriger Lösung wurde mittels Trübungsphotometer, dynamischer Lichtstreuung, TEM Messungen, NMR sowie Fluoreszenzspektroskopie untersucht. Die schrittweise Überführung eines hydrophilen in ein hydrophobes Blockcopolymer beinhaltet ein oder mehr amphiphile Zwischenstufen mit einstellbarem hydrophilen zu lipophilen Anteil (HLB). Dies führt dazu, dass die Selbstorganisation solcher Polymere in Lösung nicht nur einem Alles-oder-nichts-Prinzip folgt sondern ein mehrstufiges Aggregationsverhalten beobachtet wird. Die Synthese von doppelt thermisch schaltbaren Diblockcopolymeren und dreifach thermisch schaltbaren Triblockcopolymeren wurde durch sequenzielle RAFT Polymerisation realisiert. Dazu wurden zweifach TMS-markierte RAFT Agentien verwendet, welche die Bestimmung der molaren Masse sowie der verbliebenen Endgruppenfunktionalität direkt aus einem Protonen NMR Spektrum erlauben. Mit diesen RAFT Agentien wurde zunächst eine Serie von doppelt thermisch schaltbaren Diblockcopolymeren aus Poly(N-n-propylacrylamid)-b-Poly(N-ethylacrylamid), welche sich lediglich durch die relativen Blocklängen unterscheiden, hergestellt. In Abhängigkeit von der relativen Blocklänge wurde ein unterschiedliches Aggregationsverhalten der Diblockcopolymere in verdünnter wässriger Lösung beobachtet. Des Weiteren wirken die komplementär TMS-markierten Endgruppen als NMR-Sonden während der schrittweisen Aggregation dieser Polymere. Reversible, temperaturabhängige Peakaufspaltung der TMS-Signale in der NMR Spektroskopie spricht für eine Aggregation in gemischte stern-/blumenartige Mizellen, in denen ein Teil der hydrophoben Endgruppen in den hyrophoben Kern zurückfaltet. Obendrein wurden dreifach thermisch schaltbare Triblockcopolymere aus Poly(N-n-propylacrylamid) (A), Poly(methoxydiethylen glycol acrylat) (B) und Poly(N-ethylacrylamid) (C) in allen möglichen Blocksequenzen (ABC, BAC, ACB) durch schrittweisen Aufbau mittels RAFT Polymerisation erhalten. Das Aggregationsverhalten dieser Polymere in verdünnter wässriger Lösung war relativ komplex und hing stark von der Position der einzelnen Blöcke in den Triblockcopolymeren ab. Besonders die Position des Blocks mit der niedrigsten LCST (A) war ausschlaggebend für die resultierenden Aggregate. So wurde oberhalb der ersten Phasenübergangstemperatur nur Aggregation der Triblockcopolymere beobachtet, wenn der A Block an einem der beiden Enden der Polymere lokalisiert war. Wurde der A Block hingegen in der Mitte der Polymere positioniert, entstanden unimere Mizellen zwischen der ersten und zweiten Phasenübergangstemperatur, welche erst aggregierten, nachdem der zweite Block (B) seinen Phasenübergang durchlief. Die Transportereigenschaften dieser Triblockcopolymere wurden mittels Fluoreszenzspektroskopie getestet. Dazu wurde die Einlagerung eines hydrophoben, solvatochromen Fluoreszenzfarbstoffes, Nilrot, in Abhängigkeit der Temperatur untersucht. Im Gegensatz zu den Polymeren mit der Blocksequenz ABC oder ACB, zeigten die Polymere mit der Sequenz BAC eine verminderte Aufnahmefähigkeit des hydrophoben Farbstoffes oberhalb des ersten Phasenübergangs, was auf die fehlende Aggregation und die damit verbundenen relativ kleinen hydrophoben Domänen der unimolekularen Mizellen zwischen der ersten und zweiten Phasenübergangstemperatur zurückzuführen ist. Aufgrund des zunehmenden Verlustes von funktionellen Endgruppen während der RAFT Synthese von Triblockcopolymeren wurde ein neuartiges Konzept zur Einschrittsynthese von mehrfach schaltbaren Blockcopolymeren entwickelt. Dieses erlaubt die Synthese von mehrfach schaltbaren Diblock- und Triblockcopoylmeren in einem einzelnen Reaktionsschritt. Die Copolymeriation von verschiedenen N-substituierten Maleimiden mit einem thermisch schaltbaren Styrolderivat (4-Vinylbenzylmethoxytetrakis(oxyethylene) ether) ergab alternierende Copolymere mit variabler LCST. Die Verwendung eines Überschusses dieses styrolbasierten Monomers erlaubt ferner die Synthese von Gradientenblockcopolymeren in einem einzelnen Polymerisationsschritt. KW - Selbstorganisation KW - Blockcopolymer KW - RAFT KW - temperaturschaltbar KW - Mizelle KW - self-assembly KW - block copolymer KW - RAFT KW - thermoresponsive KW - micelle Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-53360 ER - TY - THES A1 - Wei, Chunxiang T1 - On the role of monomer drops and swelling in aqueous heterophase polymerization Y1 - 2016 ER - TY - THES A1 - Weber, Nancy T1 - Die Synthese "schizomorpher" Copolymer - Latexteilchen Y1 - 2011 CY - Potsdam ER - TY - THES A1 - Weber, Jens T1 - Meso- und mikroporöse Hochleistungspolymere : Synthese, Analytik und Anwendungen T1 - Meso- and microporous high performance polymers : synthesis, characterisation and application N2 - Die Arbeit beschreibt die Synthese, Charakterisierung und Anwendung von meso- und mikroporösen Hochleistungspolymeren. Im ersten Teil wird die Synthese von mesoporösen Polybenzimidazol (PBI) auf der Basis einer Templatierungsmethode vorgestellt. Auf der Grundlage kommerzieller Monomere und Silikatnanopartikel sowie eines neuen Vernetzers wurde ein Polymer-Silikat-Hybridmaterial aufgebaut. Das Herauslösen des Silikats mit Ammoniumhydrogendifluorid führt zu mesoporösen Polybenzimidazolen mit spherischen Poren von 9 bis 11 nm Durchmesser. Die Abhängigkeit der beobachteten Porosität vom Massenverhältnis Silikat zu Polymer wurde ebenso untersucht wie die Abhängigkeit der Porosität vom Vernetzergehalt. Die Porosität vollvernetzter Proben zeigt eine lineare Abhängigkeit vom Verhältnis Silikat zu Polymer bis zu einem Grenzwert von 1. Wird der Grenzwert überschritten, ist teilweiser Porenkollaps zu beobachten. Die Abhängigkeit der Porosität vom Vernetzergehalt bei festem Silikatgehalt ist nichtlinear. Oberhalb einer kritischen Vernetzerkonzentration wird eine komplette Replikation der Nanopartikel gefunden. Ist die Vernetzerkonzentration dagegen kleiner als der kritische Wert, so ist der völlige Kollaps einiger Poren bei Stabilität der verbleibenden Poren zu beobachten. Ein komplett unporöses PBI resultiert bei Abwesenheit des Vernetzers. Die mesoporösen PBI-Netzwerke konnten kontrolliert mit Phosphorsäure beladen werden. Die erhaltenen Addukte wurden auf ihre Protonenleitfähigkeit untersucht. Es kann gezeigt werden, dass die Nutzung der vordefinierten Morphologie im Vergleich zu einem unstrukturierten PBI in höheren Leitfähigkeiten resultiert. Durch die vernetzte Struktur war des Weiteren genügend mechanische Stabilität gegeben, um die Addukte reversibel und bei sehr guten Leitfähigkeiten bis zu Temperaturen von 190°C bei 0% relativer Feuchtigkeit zu untersuchen. Dies ist für unstrukturierte Phosphorsäure/PBI - Addukte aus linearem PBI nicht möglich. Im zweiten Teil der Arbeit wird die Synthese intrinsisch mikroporöser Polyamide und Polyimide vorgestellt. Das Konzept intrinsisch mikroporöser Polymere konnte damit auf weitere Polymerklassen ausgeweitet werden. Als zentrales, strukturinduzierendes Motiv wurde 9,9'-Spirobifluoren gewählt. Dieses Molekül ist leicht und vielfältig zu di- bzw. tetrafunktionellen Monomeren modifizierbar. Dabei wurden bestehende Synthesevorschriften modifiziert bzw. neue Vorschriften entwickelt. Ein erster Schwerpunkt innerhalb des Kapitels lag in der Synthese und Charakterisierung von löslichen, intrinsisch mikroporösen, aromatischen Polyamid und Polyimid. Es konnte gezeigt werden, dass das Beobachten von Mikroporosität stark von der molekularen Architektur und der Verarbeitung der Polymere abhängig ist. Die Charakterisierung der Porosität erfolgte unter Nutzung von Stickstoffsorption, Kleinwinkelröntgenstreuung und Molecular Modeling. Es konnte gezeigt werden, dass die Proben stark vom Umgebungsdruck abhängigen Deformationen unterliegen. Die starke Quellung der Proben während des Sorptionsvorgangs konnte durch Anwendung des "dual sorption" Modells, also dem Auftreten von Porenfüllung und dadurch induzierter Henry-Sorption, erklärt werden. Der zweite Schwerpunkt des Kapitels beschreibt die Synthese und Charakterisierung mikroporöser Polyamid- und Polyimidnetzwerke. Während Polyimidnetzwerke auf Spirobifluorenbasis ausgeprägte Mikroporosität und spezifische Oberflächen von ca. 1100 m²/g aufwiesen, war die Situation für entsprechende Polyamidnetzwerke abweichend. Mittels Stickstoffsorption konnte keine Mikroporosität nachgewiesen werden, jedoch konnte mittels SAXS eine innere Grenzfläche von ca. 300 m²/g nachgewiesen werden. Durch die in dieser Arbeit gezeigten Experimente kann die Grenze zwischen Polymeren mit hohem freien Volumen und mikroporösen Polymeren somit etwas genauer gezogen werden. ausgeprägte Mikroporosität kann nur in extrem steifen Strukturen nachgewiesen werden. Die Kombination der Konzepte "Mesoporosität durch Templatierung" und "Mikroporosität durch strukturierte Monomere" hatte ein hierarchisch strukturiertes Polybenzimidazol zum Ergebnis. Die Präsenz einer Strukturierung im molekularen Maßstab konnte SAXS bewiesen werden. Das so strukturierte Polybenzimidazol zeichnete sich durch eine höhere Protonenleitfähigkeit im Vergleich zu einem rein mesoporösen PBI aus. Der letzte Teil der Arbeit beschäftigte sich mit der Entwicklung einer neuen Synthesemethode zur Herstellung von Polybenzimidazol. Es konnte gezeigt werden, dass lineares PBI in einer eutektischen Salzschmelze aus Lithium- und Kaliumchlorid synthetisiert werden kann. Die Umsetzung der spirobifluorenbasierten Monomere zu löslichem oder vernetztem PBI ist in der Salzschmelze möglich. N2 - The first part of the thesis describes the synthesis and characterisation of cross linked, mesoporous poly(benzimidazole) (PBI) prepared by a hard templating approach. Silica nanoparticles were used as template and removed after the polycondensation by immersing the hybrid material in aqueous NH4HF2 solution. The resulting mesoporous PBI showed surface areas up to 200 m²/g as established by N2 BET and porosities up to 37 vol.-%. The influence of the template and cross linker content on the observable porosity was investigated. Nitrogen sorption and small angle x-ray scattering (SAXS) were employed as analytical techniques. The template morphology was reproduced almost perfectly, yielding spherical pores of 11 nm in diameter if the samples were fully cross linked. It was shown that there is a linear dependence of the porosity on the template content up to a critical weight ratio of silica/polymer. If the silica content is raised above 50 wt.-% partial collapse of pores is observed. The dependence of the porosity on the cross linker content at constant amount of template was found to be non-linear. At the absence of any cross linker, no porosity was observed after template removal. At 10 mol-% cross linker the onset of porosity could be observed. At higher cross linker contents, the porosity was nearly the same as for the fully cross linked PBI. The mesoporous PBI could be loaded with crystalline phosphoric acid to yield highly proton conductive materials. It was shown that the material retains its nanostructure when loaded with phosphoric acid even after annealing at 180_C for 12 h. The conductivity of the nanostructured samples was one to two orders of magnitude higher than the conductivity of a nonstructured sample. The impact of the cross linking density on the conductivity was also investigated. The second part of the work describes the synthesis and characterisation of microporous poly(amide)s and poly(imide)s. 9,9'-spirobifluorene derivatives were used to introduce a rigid, structure-directing motif which prevents the polymer chains from close packing. Firstly, the synthesis of soluble poly(amide)s and poly(imide) is described. It was observed that the microporosity is strongly dependent on the processing of the soluble polymers. In the case when polymers were precipitated from solvents of high polarity no microporosity was observed, while polymers prone to solvation in solvents of lower polarity exhibited microporosity as observed in nitrogen sorption measurements. Wide angle x-ray scattering (WAXS) showed that the microstructure was indeed dependent on the processing conditions. SAXS measurements of the polymers revealed that nitrogen sorption alone is not sufficient for the analysis of the porosity. A significant mismatch between the results obtained by the two methods indicated that only a fraction of the pore volume of the polymers was accessible for nitrogen molecules. The second part of the chapter describes the synthesis, characterisation and application of spirobifluorene based, cross linked poly(amide)s and poly(imide)s. The poly(amide) networks did not show any microporosity when analysed by nitrogen sorption. This led to the conclusion that the amide bond is too weak to withstand the interfacial forces. In contrast, poly(imide) networks exhibited pronounced microporosity with surface areas of around 1000 m2/g. The analysis of these networks was again done by nitrogen sorption and SAXS. Furthermore, molecular modelling was used to calculate the true and apparent densities of the networks. In case of the poly(imide) networks, the results of the various measurement techniques were in reasonable agreement. This indicates that the pore volume was nearly completely accessible. Finally it was established that the structure directing motif is necessary to obtain microporous polymers, as a poly(imide) prepared from a spatially undefined monomer did not feature microporosity. Pressure dependent SAXS measurements showed that the polymer networks undergo significant elastic deformations upon evacuation. This behavior complicates the analysis of the nitrogen sorption data, making it impossible to extract reliable pore size distributions. The third and last part of the thesis deals with the development of a new reaction medium for the synthesis of poly(benzimidazole). An eutectic salt melt, composed of lithium chloride and potassium chloride was used in an ionothermal synthesis of linear PBI, opening a green chemistry route towards PBI. The influence of the reaction conditions on the properties of the resulting polymers was investigated. The new reaction medium allowed furthermore the synthesis of linear and cross linked spirobifluorene based PBIs. This is not easily possible by using the classical synthetic pathways towards PBI. The spirobifluorene based PBIs synthesized in this work did, however not feature intrinsic microporosity. KW - poröse Polymere KW - Röntgenkleinwinkelstreuung KW - Gassorption KW - Protonenleitfähigkeit KW - porous polymers KW - small-angle x-ray scattering KW - gas sorption KW - proton conductivity Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-15994 ER - TY - THES A1 - Wawrzinek, Robert C. W. T1 - Fluoreszenzfarbstoffe mit Dioxolobenzodioxol-Grundgerüst: Synthese, Untersuchungen und Anwendungen Y1 - 2013 CY - Potsdam ER -