TY - THES A1 - Won, Jooyoung T1 - Dynamic and equilibrium adsorption behaviour of ß-lactoglobulin at the solution/tetradecane interface: Effect of solution concentration, pH and ionic strength T1 - Dynamik und Gleichgewicht der Adsorption von ß-Lactoglobulin an der Grenzfläche Lösung / Tetradecan (W/TD) N2 - Proteins are amphiphilic and adsorb at liquid interfaces. Therefore, they can be efficient stabilizers of foams and emulsions. β-lactoglobulin (BLG) is one of the most widely studied proteins due to its major industrial applications, in particular in food technology. In the present work, the influence of different bulk concentration, solution pH and ionic strength on the dynamic and equilibrium pressures of BLG adsorbed layers at the solution/tetradecane (W/TD) interface has been investigated. Dynamic interfacial pressure (Π) and interfacial dilational elastic modulus (E’) of BLG solutions for various concentrations at three different pH values of 3, 5 and 7 at a fixed ionic strength of 10 mM and for a selected fixed concentration at three different ionic strengths of 1 mM, 10 mM and 100 mM are measured by Profile Analysis Tensiometer PAT-1 (SINTERFACE Technologies, Germany). A quantitative data analysis requires additional consideration of depletion due to BLG adsorption at the interface at low protein bulk concentrations. This fact makes experiments more efficient when oil drops are studied in the aqueous protein solutions rather than solution drops formed in oil. On the basis of obtained experimental data, concentration dependencies and the effect of solution pH on the protein surface activity was qualitatively analysed. In the presence of 10 mM buffer, we observed that generally the adsorbed amount is increasing with increasing BLG bulk concentration for all three pH values. The adsorption kinetics at pH 5 result in the highest Π values at any time of adsorption while it exhibits a less active behaviour at pH 3. Since the experimental data have not been in a good agreement with the classical diffusion controlled model due to the conformational changes which occur when the protein molecules get in contact with the hydrophobic oil phase in order to adapt to the interfacial environment, a new theoretical model is proposed here. The adsorption kinetics data were analysed with the newly proposed model, which is the classical diffusion model but modified by assuming an additional change in the surface activity of BLG molecules when adsorbing at the interface. This effect can be expressed through the adsorption activity constant in the corresponding equation of state. The dilational visco-elasticity of the BLG adsorbed interfacial layers is determined from measured dynamic interfacial tensions during sinusoidal drop area variations. The interfacial tension responses to these harmonic drop oscillations are interpreted with the same thermodynamic model which is used for the corresponding adsorption isotherm. At a selected BLG concentration of 2×10-6 mol/l, the influence of the ionic strength using different buffer concentration of 1, 10 and 100 mM on the interfacial pressure was studied. It is affected weakly at pH 5, whereas it has a strong impact by increasing buffer concentration at pH 3 and 7. In conclusion, the structure formation of BLG adsorbed layer in the early stage of adsorption at the W/TD interface is similar to those of the solution/air (W/A) surface. However, the equation of state at the W/TD interface provides an adsorption activity constant which is almost two orders of magnitude higher than that for the solution/air surface. At the end of this work, a new experimental tool called Drop and Bubble Micro Manipulator DBMM (SINTERFACE Technologies, Germany) has been introduced to study the stability of protein covered bubbles against coalescence. Among the available protocols the lifetime between the moment of contact and coalescence of two contacting bubble is determined for different BLG concentrations. The adsorbed amount of BLG is determined as a function of time and concentration and correlates with the observed coalescence behaviour of the contacting bubbles. N2 - Die vorliegende Arbeit ist ein Beitrag zum Verständnis des Überganges von der qualitativen zur quantitativen Beschreibung der Adsorption von Proteinen an der Wasser/Öl- Grenzfläche. Dabei wird die Adsorption des Molkeproteins ß-Lactoglobulin (BLG) an der Wasser/Tetradekan (W/TD) Grenzfläche untersucht. Die Proteinadsorption an Grenzflächen zwischen zwei nicht mischbaren Flüssigkeiten ist ein Zeitprozess. Die Tropfenprofil-Analysen-Tensiometrie (PAT) hat sich als optimale Methode erwiesen, um den Prozess der Bildung von Proteinadsorptionsschichten an Flüssig-/flüssig-Grenzflächen quantitativ zu untersuchen. Die gemessenen dynamischen Grenzflächenspannungen können genutzt werden, um die adsorbierte Menge von Protein an Grenzflächen zu bestimmen. Zusätzlich erlaubt die Methode, durch periodische Tropfenoszillationen, die Messung der Dilatations-Viskoelastizität. Die experimentellen Ergebnisse zeigen deutlich, dass die Adsorption von Proteinen mit der Konzentration ansteigt. Der Adsorptionsprozess von Proteinen ist ähnlich dem von Tensiden, allerdings wird seine Beschreibung wesentlich komplizierter, durch die zusätzliche Möglichkeit der Konformationsänderungen der Proteinmoleküle an der Grenzfläche. Ein kürzlich im Rahmen dieser Dissertation entwickeltes Modell zur Adsorptionskinetik von Proteinen wurde genutzt, um experimentelle Daten für BLG zu interpretieren. Dieses kinetische Modell erlaubt es, den Mechanismus der Proteinadsorption an der Wasser/Öl-Grenzfläche zu beschreiben, was durch ältere Modelle bisher nicht möglich war. Im neu entwickelten Modell wurde die klassische Diffusionstheorie so modifiziert, dass eine Änderung der Adsorptionsaktivität der adsorbierenden Proteinmoleküle berücksichtigt wird. Die Änderung der Adsorptionsaktivität geschieht durch den Kontakt adsorbierter BLG-Moleküle an der Wasser/Öl-Grenzfläche. Es wird nach diesem neuen Modell angenommen, dass die Adsorptionsaktivität eine Funktion der Adsorptionszeit ist. Die ansteigende Adsorptionaktivität ist erforderlich, um den Adsorptionsprozess von BLG über den gesamten Zeitbereich quantitativ zu beschrieben. Mit diesem neuen Modell wurde es möglich, die experimentellen Daten zur Adsorptionskinetik sowie zur Dilatationsrheologie von Adsorptionsschichten bei unterschiedlichen BLG-Konzentrationen, pH-Werten und Ionenstärken an der Grenzfläche Lösung/Tetradekan quantitativ zu beschreiben. Die Ergebnisse dienen als Ausgangspunkt für weitere Entwicklungen zur Verbesserung des Verständnisses der Stabilität von Schäumen und Emulsionen, die durch die Dynamik der Adsorption von Molekülen wie BLG signifikant beeinflusst wird. KW - beta-lactoglobulin KW - water/tetradecane interface KW - drop profile analysis tensiometry KW - dynamic interfacial tensions KW - protein adsorption KW - pH effect KW - ionic strength effect KW - protein stabilized foams KW - drop and bubble coalescence KW - interfacial dynamics KW - capillary pressure tensiometry KW - drop-drop interaction KW - bubble-bubble interaction KW - ß-Lactoglobulin KW - Flüssig-/flüssig-Grenzflächen KW - Wasser/Öl-Grenzfläche KW - Grenzfläche Lösung/Tetradecan KW - Dynamik der Adsorption KW - Gleichgewicht der Adsorption KW - Proteinadsorption KW - Tropfenprofil-Analysen-Tensiometrie KW - Tropfenoszillationen KW - Dilatations-Viskoelastizität KW - klassische Diffusionstheorie KW - Konformationsänderungen KW - Adsorptionsaktivität KW - Wirkung des pH-Werten KW - Wirkung des Ionenstärken KW - Stabilität von Schäumen KW - Stabilität von Emulsionen Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-99167 ER - TY - THES A1 - Klier, Dennis Tobias T1 - Upconversion luminescence in Er-codoped NaYF4 nanoparticles T1 - Frequenzaufkonversion in Er-codotierten NaYF4 Nanopartikeln BT - fundamental photophysics and optimization for life science applications BT - fundamentale Photophysik und Optimierung für Anwendungen in den Lebenswissenschaften N2 - In the context of an increasing population of aging people and a shift of medical paradigm towards an individualized medicine in health care, nanostructured lanthanides doped sodium yttrium fluoride (NaYF4) represents an exciting class of upconversion nanomaterials (UCNM) which are suitable to bring forward developments in biomedicine and -biodetection. Despite the fact that among various fluoride based upconversion (UC) phosphors lanthanide doped NaYF4 is one of the most studied upconversion nanomaterial, many open questions are still remaining concerning the interplay of the population routes of sensitizer and activator electronic states involved in different luminescence upconversion photophysics as well as the role of phonon coupling. The collective work aims to explore a detailed understanding of the upconversion mechanism in nanoscaled NaYF4 based materials co-doped with several lanthanides, e.g. Yb3+ and Er3+ as the "standard" type upconversion nanoparticles (UCNP) up to advanced UCNP with Gd3+ and Nd3+. Especially the impact of the crystal lattice structure as well as the resulting lattice phonons on the upconversion luminescence was investigated in detail based on different mixtures of cubic and hexagonal NaYF4 nanoscaled crystals. Three synthesis methods, depending on the attempt of the respective central spectroscopic questions, could be accomplished in the following work. NaYF4 based upconversion nanoparticles doped with several combination of lanthanides (Yb3+, Er3+, Gd3+ and Nd3+) were synthesized successfully using a hydrothermal synthesis method under mild conditions as well as a co-precipitation and a high temperature co-precipitation technique. Structural information were gathered by means of X-ray diffraction (XRD), electron microscopy (TEM), dynamic light scattering (DLS), Raman spectroscopy and inductively coupled plasma atomic emission spectrometry (ICP-OES). The results were discussed in detail with relation to the spectroscopic results. A variable spectroscopic setup was developed for multi parameter upconversion luminescence studies at various temperature 4 K to 328 K. Especially, the study of the thermal behavior of upconversion luminescence as well as time resolved area normalized emission spectra were a prerequisite for the detailed understanding of intramolecular deactivation processes, structural changes upon annealing or Gd3+ concentration, and the role of phonon coupling for the upconversion efficiency. Subsequently it became possible to synthesize UCNP with tailored upconversion luminescence properties. In the end, the potential of UCNP for life science application should be enunciated in context of current needs and improvements of a nanomaterial based optical sensors, whereas the "standard" UCNP design was attuned according to the special conditions in the biological matrix. In terms of a better biocompatibility due to a lower impact on biological tissue and higher penetrability for the excitation light. The first step into this direction was to use Nd3+ ions as a new sensitizer in tridoped NaYF4 based UCNP, whereas the achieved absolute and relative temperature sensitivity is comparable to other types of local temperature sensors in the literature. N2 - Ziel der Arbeit war es ein erweitertes Verständnis des Mechanismus der Lichtaufkonversion, sowie dessen gezielte Manipulation in verschiedenen Nanomaterialien auf Natriumyttrium-fluoridbasis zu erlangen. Die optischen Eigenschaften werden dabei durch eine gezielte Zusammenstellung verschiedener Lanthanoidionen hervorgerufen, welche während der Synthese in die Materialien eingebracht werden. Der Fokus lag hierbei in der Aufklärung des Zusammenspiels zwischen der Struktur der Materialien und deren Lichtaufkonver-sionsvermögen sowie dem Erlangen eines generellen Verständnisses der einzelnen Teilschritte des Lichtaufkonversionsmechanismus. Dabei wird das Licht, welches nach Anregung der Lanthanoidionen durch einen Laser von diesen emittiert wird, hinsichtlich der Farbzusammensetzung und des Abklingverhaltens der Lumineszenz untersucht. Diese Erkenntnisse geben sowohl einen Einblick in die verschiedenen Teilschritte des Lichtaufkonversionsmechanismus, als auch deren Korrelation zur Struktur der Nanomaterialien. Während der Arbeit wurde ein variabler Messplatz mit einer wellenlängendurchstimmbaren Anregungslichtquelle, einer Detektionseinheit mit hervorragender spektraler und zeitlicher Auflösung für die Messung des emittierten Lichtes sowie einer Temperiereinheit, mit der die Proben in einem Temperaturbereich von 4 Kelvin (-269,15 °C) bis 328 Kelvin (50 °C) temperiert werden können, aufgebaut. Die Proben wurden mithilfe der modernen Kopräzipitations- und Hydrothermalsynthese in verschiedenen Zusammensetzungen und Oberflächenmodifizierungen hergestellt, um sowohl Partikel für fundamentale Untersuchungen der Lichtaufkonversion verfügbar zu haben, als auch den hohen Anforderungen für Anwendungen in den Lebenswissenschaften gerecht zu werden. Die Reaktion fand bei hohen Temperaturen (160 °C bis 320 °C) unter Schutzgasatmosphäre statt und gewährleistete so die Bildung von hochkristallinen Partikeln, deren Größe stark mit der Synthesetemperatur korreliert. Mithilfe von zeitaufgelösten Lumineszenzuntersuchungen gelang ein sehr detaillierter Einblick in strukturelle Veränderungen der Nanopartikeln, welche durch klassische strukturanalytische Methoden, wie der Röntgenpulverdiffraktometrie, nicht in dem Maße möglich sind. Zudem konnte ein erheblicher Teil dazu beigetragen werden, das komplexe Zusammenspiel von Energietransportmechanismen, Gitterschwingungen und thermisch induzierten Prozessen zu verstehen. Zuletzt wurden, basierend auf der Vielzahl an gewonnenen Erkenntnissen, speziell designte Nanopartikel hergestellt. Die Farbe des Emissionslichts dieser Partikel wies dabei eine hohe Abhängigkeit von der Umgebungstemperatur auf. Auftretende Herausforderungen induziert durch das verwendete Anregungslicht im Nahinfrarotenbereich, wie das Aufheizen oder die zu hohe Absorption der Probe, wurden durch die Erweiterung des Aufkonversionssystems gelöst. Damit konnten beste Voraussetzungen für potentielle Anwendungen, wie zum Beispiel als Nanothermometer geschaffen werden. KW - Nanopartikel KW - nanoparticle KW - Frequenzaufkonversion KW - upconversion KW - Lanthanoide KW - lanthanides Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98486 ER - TY - THES A1 - Couturier, Jean-Philippe T1 - New inverse opal hydrogels as platform for detecting macromolecules T1 - Neue inverse Opal-Hydrogele als Plattform für die Detektion von Makromolekülen N2 - In this thesis, a route to temperature-, pH-, solvent-, 1,2-diol-, and protein-responsive sensors made of biocompatible and low-fouling materials is established. These sensor devices are based on the sensitivemodulation of the visual band gap of a photonic crystal (PhC), which is induced by the selective binding of analytes, triggering a volume phase transition. The PhCs introduced by this work show a high sensitivity not only for small biomolecules, but also for large analytes, such as glycopolymers or proteins. This enables the PhC to act as a sensor that detects analytes without the need of complex equipment. Due to their periodical dielectric structure, PhCs prevent the propagation of specific wavelengths. A change of the periodicity parameters is thus indicated by a change in the reflected wavelengths. In the case explored, the PhC sensors are implemented as periodically structured responsive hydrogels in formof an inverse opal. The stimuli-sensitive inverse opal hydrogels (IOHs) were prepared using a sacrificial opal template of monodispersed silica particles. First, monodisperse silica particles were assembled with a hexagonally packed structure via vertical deposition onto glass slides. The obtained silica crystals, also named colloidal crystals (CCs), exhibit structural color. Subsequently, the CCs templates were embedded in polymer matrix with low-fouling properties. The polymer matrices were composed of oligo(ethylene glycol) methacrylate derivatives (OEGMAs) that render the hydrogels thermoresponsive. Finally, the silica particles were etched, to produce highly porous hydrogel replicas of the CC. Importantly, the inner structure and thus the ability for light diffraction of the IOHs formed was maintained. The IOH membrane was shown to have interconnected pores with a diameter as well as interconnections between the pores of several hundred nanometers. This enables not only the detection of small analytes, but also, the detection of even large analytes that can diffuse into the nanostructured IOH membrane. Various recognition unit – analyte model systems, such as benzoboroxole – 1,2-diols, biotin – avidin and mannose – concanavalin A, were studied by incorporating functional comonomers of benzoboroxole, biotin and mannose into the copolymers. The incorporated recognition units specifically bind to certain low and highmolar mass biomolecules, namely to certain saccharides, catechols, glycopolymers or proteins. Their specific binding strongly changes the overall hydrophilicity, thus modulating the swelling of the IOH matrices, and in consequence, drastically changes their internal periodicity. This swelling is amplified by the thermoresponsive properties of the polymer matrix. The shift of the interference band gap due to the specific molecular recognition is easily visible by the naked eye (up to 150 nm shifts). Moreover, preliminary trial were attempted to detect even larger entities. Therefore anti-bodies were immobilized on hydrogel platforms via polymer-analogous esterification. These platforms incorporate comonomers made of tri(ethylene glycol) methacrylate end-functionalized with a carboxylic acid. In these model systems, the bacteria analytes are too big to penetrate into the IOH membranes, but can only interact with their surfaces. The selected model bacteria, as Escherichia coli, show a specific affinity to anti-body-functionalized hydrogels. Surprisingly in the case functionalized IOHs, this study produced weak color shifts, possibly opening a path to detect directly living organism, which will need further investigations. N2 - Periodisch strukturierte, funktionelle responsive Hydrogele wurden in Form von inversen Opalen (IOH) aufgebaut und als Basiselement für Temperatur-, pH-, lösungsmittel-, 1,2-diol- oder protein-sensitive Sensorsysteme entwickelt. Dazu wurden aus biokompatiblen Bausteinen funktionelle photonische Kristalle aufgebaut, deren optische Bandlücke durch selektive Bindung eines Analyten moduliert wird, indem dieser einen Volumen-Phasenübergang induziert.Mittels solcher responsiver photonische Kristalle ist es möglich, Analyte ohne aufwendige Geräte durch Farbänderung einfach zu detektieren. Die entwickelten Systeme zeigen nicht nur eine hohe Empfindlichkeit gegenüber kleinen Biomolekülen, sondern auch gegenüber größeren Analyten wie z.B. Glycopolymeren und Proteinen, was bisher nicht bekannt war. Die stimuli-sensitiven inversen Opal Hydrogele (IOHs) wurden in mehreren Stufen hergestellt. Als erstes wurden dafür kolloidale Kristalle mit hexagonal gepackten Strukturen aus monodispersen SiO2-Partikeln auf Glasträgern auf ebaut (“Opal”). Die Opale mit charakteristischen Strukturfarben wurden anschließend in eine polymere Hydrogelmatrix eingebettet. Diese wurde aus Oligo(ethylenglycol)methacrylaten (OEGMAs) hergestellt, so dass die Hydrogele sowohl thermosensitives als auch “lowfouling” Verhalten zeigen. Im letzten Schritt wurden die SiO2-Partikel entfernt und so eine hochporöse Hydrogel-Replika der Opale erhalten unter Erhalt deren innerer Struktur und Strukturfarbe. Die miteinander verbunden Poren der IOHMembran besitzen einen Durchmesser von einigen hundert Nanometern. Dies ermöglichte nicht nur die Detektion von kleinen Analyten, sondern auch die Detektion von deutlich größeren, makromolekularen Analyten, die ebenfalls in die Nanostrukturen der IOH Membran diffundieren können. Modellsysteme bestanden immer aus einer Erkennungsgruppe und einem Analyten, beispielsweise aus Benzoboroxol – 1,2-Diol, Biotin – Avidin und Mannose – Lectin (Concanavalin A). Für dieseModellsysteme wurden OEGMAs mitMonomeren copolymerisiert, die mit Benzoboroxol, Biotin bzw.Mannose funktionalisiert waren. Die so im Polymer eingebauten Erkennungsgruppen binden spezifisch an bestimmte Biomoleküle unterschiedlicherMolmassen, wie z.B. niedermolekulare Saccharide oder Catechin, als auch hochmolekulare Glycopolymere oder Proteine. Der spezifische Bindungsvorgang moduliert die Gesamthydrophilie, so dass sich der Quellgrad der IOH-Matrix ändert. Dies wiederrumverändert die innere Periodizität und damit die Strukturfarbe. Dabei wird der Quelleffekt durch die Thermosensitivität der Hydrogele massiv verstärkt. Eine spezifischeMolekülanbindung lässt sich so optisch, z.T. sogar mit dem Auge, erkennen aufgrund der deutlichen Verschiebung der Strukturfarbe um bis zu 150 nm. Des Weiteren wurden auch erste Versuche zur Detektion von noch größeren Analyten unternommen. Dafür wurden Antiköper durch nachträgliche Modifizierung der Polymerseitenketten auf den Hydrogeloberflächen immobilisiert. Mit diesem Modellsystem konnten unterschiedliche Bakterienarten durch Antikörper spezifisch gebunden werden. Die verwendeten Bakterienarten sind zwar zu groß, um in die Membran des IOH Systems einzudringen, können jedoch mit der IOH-Oberfläche wechselwirken. Insbesondere dasModellsystem mit Escherichia coli zeigte eine starke, spezifische Affinität zu dem Antikörper-funktionalisierten IOH. Überraschenderweise zeigte sich bei den Versuchen in Gegenwart des Analyten eine kleine Farbänderung der funktionalisierten IOH. Damit eröffnet sich u.U. dieMöglichkeit, mit solchen responsiven photonischen Kristallen auch lebende Organismen spezifisch und einfach zu detektieren, was in weiterführenden Arbeiten zu klären sein wird. KW - inverse opal KW - hydrogel KW - responsive polymer KW - inverse Opale KW - Hydrogel KW - schaltbare Polymere Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98412 ER - TY - THES A1 - Stahlhut, Frank T1 - Entwicklung neuer triphiler, fluorkohlenstofffreier Blockcopolymere und Untersuchung ihrer Eigenschaften für Multikompartiment-Mizellen T1 - Synthesis of new triphilic fluorocarbon -free block copolymers and analysis of their suitability as multicompartment micelles N2 - Neue Systeme für triphile, fluorkohlenstofffreie Blockcopolymere in Form von Acrylat-basierten thermoresponsiven Blockcopolymeren sowie Acrylat- bzw. Styrol-basierten Terblock-Polyelektrolyten mit unterschiedlich chaotropen Kationen des jeweiligen polyanionischen Blocks wurden entwickelt. Multikompartiment-Mizellen, mizellare Aggregate mit ultrastrukturiertem hydrophobem Mizellkern die biologischen Strukturen wie dem Humanalbumin nachempfunden sind, sollten bei der Selbstorganisation in wässriger Umgebung entstehen. Durch Verwendung apolarer und polarer Kohlenwasserstoff-Domänen anstelle von fluorophilen Fluorkohlenstoff-Domänen sollte erstmals anhand solcher triphilen Systeme nachgewiesen werden, ob diese in der Lage zur selektiven Aufnahme hydrophober Substanzen in unterschiedliche Domänen des Mizellkerns sind. Mit Hilfe von sequentieller RAFT-Polymerisation wurden diese neuen triphilen Systeme hergestellt, die über einen permanent hydrophilen, eine permanent stark hydrophoben und einen dritten Block verfügen, der durch externe Einflüsse, speziell die Induzierung eines thermischen Coil-to-globule-Übergangs bzw. die Zugabe von organischen, hydrophoben Gegenionen von einem wasserlöslichen in einen polar-hydrophoben Block umgewandelt werden kann. Als RAFT-Agens wurde 4-(Trimethylsilyl)benzyl(3-(trimethylsilyl)-propyl)-trithiocarbonat mit zwei unterschiedlichen TMS-Endgruppen verwendet, das kontrollierte Reaktions-bedingungen sowie die molekulare Charakterisierung der komplexen Copolymere ermöglichte. Die beiden Grundtypen der linearen ternären Blockcopolymere wurden jeweils in zwei 2 Modell-Systeme, die geringfügig in ihren chemischen Eigenschaften sowie in dem Blocklängenverhältnis von hydrophilen und hydrophoben Polymersegmenten variierten, realisiert und unterschiedliche Permutation der Blöcke aufwiesen. Als ersten Polymertyp wurden amphiphile thermoresponsive Blockcopolymere verwendet. Modell-System 1 bestand aus dem permanent hydrophoben Block Poly(1,3-Bis(butylthio)-prop-2-yl-acrylat), permanent hydrophilen Block Poly(Oligo(ethylenglykol)monomethyletheracrylat) und den thermoresponsiven Block Poly(N,N‘-Diethylacrylamid), dessen Homopolymer eine LCST-Phasenübergang (LCST, engl.: lower critical solution temperature) bei ca. 36°C aufweist. Das Modell-System 2 bestand aus dem permanent hydrophilen Block Poly(2-(Methylsulfinyl)ethylacrylat), dem permanent hydrophoben Block Poly(2-Ethylhexylacrylat) und wiederum Poly(N,N‘-Diethylacrylamid). Im ternären Blockcopolymer erhöhte sich, je nach Blocksequenz und relativen Blocklängen, der LCST-Übergang auf 50 – 65°C. Bei der Untersuchung der Selbstorganisation für die Polymer-Systeme dieses Typs wurde die Temperatur variiert, um verschieden mizellare Überstrukturen in wässriger Umgebung zu erzeugen bzw. oberhalb des LCST-Übergangs Multikompartiment-Mizellen nachzuweisen. Die Unterschiede in der Hydrophilie bzw. den sterischen Ansprüche der gewählten hydrophilen Blöcke sowie die Variation der jeweiligen Blocksequenzen ermöglichte darüber hinaus die Bildung verschiedenster Morphologien mizellarer Aggregate. Der zweite Typ basierte auf ein Terblock-Polyelektrolyt-System mit Polyacrylaten bzw. Polystyrolen als Polymerrückgrat. Polymere ionische Flüssigkeiten wurden als Vorlage der Entwicklung zweier Modell-Systeme genommen. Eines der beiden Systeme bestand aus dem permanent hydrophilen Block Poly(Oligo(ethylenglykol)monomethyletheracrylat, dem permanent hydrophoben Block Poly(2-Ethylhexylacrylat) sowie dem Polyanion-Block Poly(3-Sulfopropylacrylat). Die Hydrophobie des Polyanion-Blocks variierte durch Verwendung großer organischer Gegenionen, nämlich Tetrabutylammonium, Tetraphenylphosphonium und Tetraphenylstibonium. Analog wurde in einem weiteren System aus dem permanent hydrophilen Block Poly(4-Vinylbenzyltetrakis(ethylenoxy)methylether), dem permanent hydrophoben Block Poly(para-Methylstyrol) und Poly(4-Styrolsulfonat) mit den entsprechenden Gegenionen gebildet. Aufgrund unterschiedlicher Kettensteifigkeit in beiden Modell-Systemen sollte es bei der Selbstorganisation der mizellarer Aggregate zu unterschiedlichen Überstrukturen kommen. Mittels DSC-Messungen konnte nachgewiesen werden, dass für alle Modell-Systeme die Blöcke in Volumen-Phase miteinander inkompatibel waren, was eine Voraussetzung für Multikompartimentierung von mizellaren Aggregaten ist. Die Größe mizellarer Aggregate sowie der Einfluss externer Einflüsse wie der Veränderung der Temperatur bzw. der Hydrophobie und Größe von Gegenionen auf den hydrodynamischen Durchmesser mittels DLS-Untersuchungen wurden für alle Modell-Systeme untersucht. Die Ergebnisse zu den thermoresponsiven ternären Blockcopolymeren belegten , dass sich oberhalb der Phasenübergangstemperatur des thermoresponsiven Blocks die Struktur der mizellaren Aggregate änderte, indem der p(DEAm)-Block scheinbar kollabierte und so zusammen mit den permanent hydrophoben Block den jeweiligen Mizellkern bildete. Nach gewisser Equilibrierungszeit konnten bei Raumtemperatur dir ursprünglichen mizellaren Strukturen regeneriert werden. Hingegen konnte für die Terblock-Polyelektrolyt-Systeme bei Verwendung der unterschiedlich hydrophoben Gegenionen kein signifikanter Unterschied in der Größe der mizellaren Aggregate beobachtet werden. Zur Abbildung der mizellaren Aggregate mittels kryogene Transmissionselektronenmikroskopie (cryo-TEM) der mizellaren Aggregate war mit Poly(1,3-Bis(butylthio)-prop-2-yl-acrylat) ein Modell-System so konzipiert, dass ein erhöhter Elektronendichtekontrast durch Schwefel-Atome die Visualisierung ultrastrukturierter hydrophober Mizellkerne ermöglichte. Dieser Effekt sollte in den Terblock-Polyelektrolyt-Systemen auch durch die Gegenionen Tetraphenylphosphonium und Tetraphenylstibonium nachgestellt werden. Während bei den thermoresponsiven Systemen auch oberhalb des Phasenübergangs kein Hinweis auf Ultrastrukturierung beobachtet wurde, waren für die Polyelektrolyt-Systeme, insbesondere im Fall von Tetraphenylstibonium als Gegenion Überstrukturen zu erkennen. Der Nachweis der Bildung von Multikompartiment-Mizellen war für beide Polymertypen mit dieser abbildenden Methode nicht möglich. Die Unterschiede in der Elektronendichte einzelner Blöcke müsste möglicherweise weiter erhöht werden um Aussagen diesbezüglich zu treffen. Die Untersuchung von ortsspezifischen Solubilisierungsexperimenten mit solvatochromen Fluoreszenzfarbstoffen mittels „steady-state“-Fluoreszenzspektroskopie durch Vergleich der Solubilisierungsorte der Terblockcopolymere bzw. –Polyelektrolyte mit den jeweiligen Solubilisierungsorten von Homopolymer- und Diblock-Vorstufen sollten den qualitativen Nachweis der Multikompartimentierung erbringen. Aufgrund der geringen Mengen an Farbstoff, die für die Solubilisierungsexperimente eingesetzt wurden zeigten DLS-Untersuchungen keine störenden Effekte der Sonden auf die Größe der mizellaren Aggregate. Jedoch erschwerten Quench-Effekte im Falle der Polyelektrolyt Modell-Systeme eine klare Interpretation der Daten. Im Falle der Modell-Systeme der thermoresponsiven Blockcopolymere waren dagegen deutliche solvatochrome Effekte zwischen der Solubilisierung in den mizellaren Aggregaten unterhalb und oberhalb des Phasenübergangs zu erkennen. Dies könnte ein Hinweis auf Multikompartimentierung oberhalb des LCST-Übergangs sein. Ohne die Informationen einer Strukturanalyse wie z.B. der Röntgen- oder Neutronenkleinwinkelstreuung (SAXS oder SANS), kann nicht abschließend geklärt werden, ob die Solubilisierung in mizellaren hydrophoben Domänen des kollabierten Poly(N,N‘-Diethylacrylamid) erfolgt oder in einer Mischform von mizellaren Aggregaten mit gemittelter Polarität. N2 - New systems for triphilic fluorine-carbon-free block copolymers in the form of acrylate-based thermoresponsive block copolymers and acrylate- and styrene-based ternary block polyelectrolytes with different chaotropic cations of the respective polyanionic blocks have been developed. Multicompartment micelles, micellar aggregates with ultrastructured hydrophobic micelle core which are bio-inspired by biological structures like human serum albumin, should occur during the self-assembly in aqueous environment. By having nonpolar and polar hydrocarbon domains instead of fluorocarbon domains in these triphilic systems, it should be possible to demonstrate for the first time, whether they are capable of selectively uptaking hydrophobic substances in different hydrophobic domains of the micelle core. These new triphilic systems were prepared by using sequential RAFT polymerization. These polymers are based on a permanently hydrophilic polymer block; a permanent highly hydrophobic block and a third block which is sensitive to the result of external influences, especially the induction of a thermal coil-to-globule transition in the case of thermoresponsive block copolymers or adding organic hydrophobic counter ions in the case of block polyelectrolytes. The third block for each system can be converted from a water-soluble in a polar hydrophobic block due to external stimulus. The RAFT agent, 4- (trimethylsilyl) benzyl (3- (trimethylsilyl) propyl) trithiocarbonate, has two different TMS-labeled end groups, which enable controlled polymerization conditions and the exact molecular characterization of the complex copolymers. Each of the two basic types of linear ternary block copolymers, which were prepared for this work, were implemented in two 2 model systems that varied slightly in their chemical properties, as well as in the block length ratio of hydrophilic and hydrophobic polymer segments and different block sequences. The first polymer type is based on amphiphilic thermoresponsive block copolymers. Model system 1 consisted of the permanent hydrophobic block p(1,3-bis (butylthio) prop-2-yl acrylate), the permanently hydrophilic block p(oligo (ethylene glycol) mono methyl ether acrylate) and the thermoresponsive block p(N,N–diethyl acrylamide) whose homopolymer has a LCST (lower critical solution temperature) like phase transition approximately about 36°C. The model system 2 consisted of the permanent hydrophilic block p(2- (methylsulfinyl) ethyl acrylate), the permanently hydrophobic block p(2-ethylhexyl acrylate) and again p(N,N–diethyl acrylamide). The LCST is increased in ternary block copolymers to 50 - 65°C, depending on the block sequence and relative block lengths. To study the self-assembly of these two polymer systems, their aqueous micellar solutions where analyzed above and below LCST to produce different micellar superstructures in an aqueous environment and to prove the occurrence of multicompartment micelles above LCST. The differences in the hydrophilicity or the individual steric requirements of the chosen hydrophilic blocks as well as the variation of the respective block sequences lead additionally to different morphologies of micellar aggregates. The second type of polymers is based on ternary block polyelectrolytes with polyacrylates and polystyrenes as polymer backbone respectively. Polymeric ionic liquids were taken as role model for the development of two model systems of block polyelectrolytes. One of the two systems consisting of the permanently hydrophilic p(oligo (ethylene glycol) mono methyl ether acrylate), the permanent hydrophobic block p(2-ethylhexyl acrylate) and the polyanion block p(3-sulfopropyl acrylate) (= model system 3). The hydrophobicity of the polyanion blocks varied largely by using organic counter ions, namely tetrabutyl ammonium, tetraphenyl phosphonium and tetraphenyl stibonium. Analogously, model system 4 consists of a permanently hydrophilic block p(4-vinylmethoxybenzyltetrakis (oxyethylene) ether), a permanently hydrophobic block p(para-methyl styrene) and p(4-styrene sulfonate) formed with the corresponding counter ions. Due to different chain stiffness in both model systems there should be different superstructures of micellar aggregates in aqueous solution. DSC (differential scanning calorimetry) measurements could demonstrate that the all polymer blocks for each modell system were incompatible with each other in bulk phase. This property is a prerequisite for ultra-structured hydrophobic cores of micellar aggregates. The influence of external factors such as change of temperature or change of hydrophobicity and size of counter ions on the size of micellar aggregates for all model systems was examined by DLS measurements. The results on the thermoresponsive ternary block copolymers showed that above the phase transition temperature of the thermo-responsive block the structure of micellar aggregates changed because the p(N,N–diethyl acrylamide) block apparently collapsed formed a subdivided micellar core together with the permanently hydrophobic block. Some equilibration time for the thermoresponsive block copolymer systems were needed to ensure that heoriginal micellar structures could be regenerated after cooling heated auqeous micellar solutions to room temperature. However, for the ternary block polyelectrolytes, there was no significant difference in the size of the micellar aggregates due to the exchange of counter ions which differ by their hydrophobicity. For imaging the micellar aggregates and especially multicompartment micelles by means of cryogenic transmission electron microscopy (cryo-TEM), the model system 1 with p(1,3-bis (butylthio) -prop-2-yl acrylate) as permanently hydrophobic block was specifically designed so that the increased electron density contrast by sulfur atoms should enable the visualization of multicompartment micelles. This effect should be readjusted in the ternary block polyelectrolyte systems by the counter ions tetraphenyl phosphonium and tetraphenyl stibonium. While in the thermoresponsive block copolymer systems it was possible to observe new kinds of micellar aggregates above LCST, there was no indication on ultrastructuring in the micellar cores for all analyzed systems. Otherwise by using tetraphenyl stibonium counter ions in block polyelectrolyte systems, some kind of ultrastructured micellar aggregates with seemingly subdivided micellar cores could be observed. The detection of the formation of multicompartment micelles was not possible for both types of polymers with this direct imaging method. The differences in the electron density of individual blocks might have to be further increased to make statements concerning the self-assembly into multicompartment micelles. Site-specific solubilization experiments with solvatochromic fluorescent dyes by using steady-state fluorescence spectroscopy should provide the qualitative evidence of multicompartment micelles. The selective solubilization areas of different kinds of substances in self-assembled structures of all ternary block copolymers and ternary polyelectrolytes were compared with the solubilization areas in their respective homopolymer and diblock precursors. Because of the small amounts of dye that have been used for the solubilization DLS measurements showed no interfering effects of the probes on the size of the micellar aggregates. However, quenching effects made a clear interpretation of the data in the case of polyelectrolyte model systems difficult. In the case of model systems 1 and 2 a change of the solubilization areas of fluorescent dyes due to the occurrence significant solvatochromic effects (stokes shifts) above LCST could be observed. The effect was reversibel. This could be an indication that the micellar aggregates self-assemble into multicompartment micelles above the LCST transition. Without the information of a structural analysis such as the small angle x-ray scattering or small angle neutron scattering (SAXS or SANS), it cannot be conclusively clarified whether the solubilization occurs in micellar hydrophobic domains of the collapsed p(N,N–diethyl acrylamide), or in a mixed form of micellar aggregates with mixed polarity. KW - Blockcopolymere KW - RAFT KW - Multikompartiment-Mizellen KW - cryo-TEM KW - Solubilisierung KW - Fluoereszenzsonden KW - block copolymers KW - triphilic KW - RAFT KW - multicompartment micelles KW - cryo-TEM KW - fluorescent dyes KW - fluorescence probe experiments KW - triphil Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-96299 SP - iv, 191 ER - TY - THES A1 - Riebe, Daniel T1 - Experimental and theoretical investigations of molecular ions by spectroscopy as well as ion mobility and mass spectrometry T1 - Experimentelle und theoretische Untersuchungen molekularer Ionen durch Spektroskopie sowie Ionenmobilitäts- und Massenspektrometrie N2 - The aim of this thesis was the elucidation of different ionization methods (resonance-enhanced multiphoton ionization – REMPI, electrospray ionization – ESI, atmospheric pressure chemical ionization – APCI) in ion mobility (IM) spectrometry. In order to gain a better understanding of the ionization processes, several spectroscopic, mass spectrometric and theoretical methods were also used. Another focus was the development of experimental techniques, including a high resolution spectrograph and various combinations of IM and mass spectrometry. The novel high resolution 2D spectrograph facilitates spectroscopic resolutions in the range of commercial echelle spectrographs. The lowest full width at half maximum of a peak achieved was 25 pm. The 2D spectrograph is based on the wavelength separation of light by the combination of a prism and a grating in one dimension, and an etalon in the second dimension. This instrument was successfully employed for the acquisition of Raman and laser-induced breakdown spectra. Different spectroscopic methods (light scattering and fluorescence spectroscopy) permitting a spatial as well as spectral resolution, were used to investigate the release of ions in the electrospray. The investigation is based on the 50 nm shift of the fluorescence band of rhodamine 6G ions of during the transfer from the electrospray droplets to the gas phase. A newly developed ionization chamber operating at reduced pressure (0.5 mbar) was coupled to a time-of-flight mass spectrometer. After REMPI of H2S, an ionization chemistry analogous to H2O was observed with this instrument. Besides H2S+ and its fragments, H3S+ and protonated analyte ions could be observed as a result of proton-transfer reactions. For the elucidation of the peaks in IM spectra, a combination of IM spectrometer and linear quadrupole ion trap mass spectrometer was developed. The instrument can be equipped with various ionization sources (ESI, REMPI, APCI) and was used for the characterization of the peptide bradykinin and the neuroleptic promazine. The ionization of explosive compounds in an APCI source based on soft x-radiation was investigated in a newly developed ionization chamber attached to the ion trap mass spectrometer. The major primary and secondary reactions could be characterized and explosive compound ions could be identified and assigned to the peaks in IM spectra. The assignment is based on the comparison of experimentally determined and calculated IM. The methods of calculation currently available exhibit large deviations, especially in the case of anions. Therefore, on the basis of an assessment of available methods, a novel hybrid method was developed and characterized. N2 - Ziel dieser Arbeit war die Aufklärung unterschiedlicher Ionisationsmethoden (Resonanz-verstärkte Mehrphotonenionisation – REMPI, Elektrosprayionisation – ESI, chemische Ionisation bei Atmosphärendruck – APCI) in der Ionenmobilitäts (IM)-Spektrometrie. Um ein besseres Verständnis der Ionisationsprozesse zu erhalten, wurden zusätzlich ver¬schiedene spektroskopische, massenspektrometrische und theoretische Methoden eingesetzt. Ein weiterer Schwerpunkt war die Entwicklung neuer experimenteller Techniken, darunter ein hochauflösender Spektrograph und verschiedene Kombinationen von IM- und Massenspektrometern. Der neuartige, hochauflösende 2D Spektrograph ermöglicht spektroskopische Auflösungen im Bereich kommerzieller Echelle-Spektrographen. Die geringste erreichte Halbwertsbreite eines Peaks betrug 25 pm. Der 2D Spektrograph beruht auf der Wellenlängenseparation von Licht durch eine Kombination aus einem Prisma und einem Gitter in der einen Dimension und einem Etalon in der zweiten Dimension. Das Instrument wurde erfolgreich zur Aufnahme von Raman- und laserinduzierten Plasmaspektren ein¬gesetzt. Verschiedene spektroskopische Methoden (Lichtstreuung und Fluoreszenzspektroskopie), die sowohl eine räumliche, als auch eine spektrale Auflösung erlauben, wurden zur Untersuchung der Freisetzung der Ionen im Elektrospray angewandt. Die Untersuchung beruht auf der Verschiebung der Fluoreszenzbande von Rhodamin 6G-Ionen um 50 nm beim Übergang aus den Elektrospray-Tropfen in die Gasphase. Eine neuent¬wickelte Ionisationskammer bei reduziertem Druck (0,5 mbar) wurde an ein Flugzeit-Massenspektrometer gekoppelt. Darin wurde nach REMPI von H2S eine zum H2O analoge Ionisationschemie beobachtet. Neben H2S+ und seinen Fragmenten wurden als Ergebnis von Proto-nen-Transferreaktionen H3S+ und protonierte Analytionen beobachtet. Zur Aufklärung der Peaks in IM-Spektren wurde eine Kopplung von IM-Spektrometer und linearem Quadrupol-Ionenfallen-Massenspektrometer entwickelt. Die Kopplung kann mit verschiedenen Ionisationsquellen (ESI, REMPI, APCI) ausgestattet werden und wurde zur Charakterisierung des Peptids Bradykinin und des Neuroleptikums Promazin angewendet. Die Ionisation von Sprengstoffen in einer APCI-Quelle, die auf weicher Röntgenstrahlung beruht, wurde in einer neu entwickelten, an das Ionenfallen-Massenspektrometer gekoppelten Ionisationskammer untersucht. Dabei konnten die wichtigsten Primär- und Sekundärreaktionen charakterisiert, sowie Sprengstoffionen identifiziert und den Peaks in den IM-Spektren zugeordnet werden. Diese Zuordnung beruht auf dem Vergleich von experimentell bestimmten und berechneten IM. Da die aktuell verfügbaren Berechnungsmethoden insbesondere für Anionen zu große Abweichungen zu den experimentell bestimmten IM aufweisen, wurde auf Basis der Bewertung verfügbarer Methoden eine neue Hybridmethode entwickelt und charakterisiert. KW - ion mobility spectrometry KW - mass spectrometry KW - explosives KW - X-ray KW - photoionization KW - ion mobility calculations KW - Ionenmobilitätsspektrometrie KW - Massenspektrometrie KW - Sprengstoffe KW - Röntgenstrahlung KW - Photoionisation KW - Ionenmobilitäts-Berechnungen Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-94632 ER - TY - THES A1 - Ulaganathan, Vamseekrishna T1 - Molecular fundamentals of foam fractionation T1 - Molekulare Grundlagen der Schaumfraktionierung N2 - Foam fractionation of surfactant and protein solutions is a process dedicated to separate surface active molecules from each other due to their differences in surface activities. The process is based on forming bubbles in a certain mixed solution followed by detachment and rising of bubbles through a certain volume of this solution, and consequently on the formation of a foam layer on top of the solution column. Therefore, systematic analysis of this whole process comprises of at first investigations dedicated to the formation and growth of single bubbles in solutions, which is equivalent to the main principles of the well-known bubble pressure tensiometry. The second stage of the fractionation process includes the detachment of a single bubble from a pore or capillary tip and its rising in a respective aqueous solution. The third and final stage of the process is the formation and stabilization of the foam created by these bubbles, which contains the adsorption layers formed at the growing bubble surface, carried up and gets modified during the bubble rising and finally ends up as part of the foam layer. Bubble pressure tensiometry and bubble profile analysis tensiometry experiments were performed with protein solutions at different bulk concentrations, solution pH and ionic strength in order to describe the process of accumulation of protein and surfactant molecules at the bubble surface. The results obtained from the two complementary methods allow understanding the mechanism of adsorption, which is mainly governed by the diffusional transport of the adsorbing protein molecules to the bubble surface. This mechanism is the same as generally discussed for surfactant molecules. However, interesting peculiarities have been observed for protein adsorption kinetics at sufficiently short adsorption times. First of all, at short adsorption times the surface tension remains constant for a while before it decreases as expected due to the adsorption of proteins at the surface. This time interval is called induction time and it becomes shorter with increasing protein bulk concentration. Moreover, under special conditions, the surface tension does not stay constant but even increases over a certain period of time. This so-called negative surface pressure was observed for BCS and BLG and discussed for the first time in terms of changes in the surface conformation of the adsorbing protein molecules. Usually, a negative surface pressure would correspond to a negative adsorption, which is of course impossible for the studied protein solutions. The phenomenon, which amounts to some mN/m, was rather explained by simultaneous changes in the molar area required by the adsorbed proteins and the non-ideality of entropy of the interfacial layer. It is a transient phenomenon and exists only under dynamic conditions. The experiments dedicated to the local velocity of rising air bubbles in solutions were performed in a broad range of BLG concentration, pH and ionic strength. Additionally, rising bubble experiments were done for surfactant solutions in order to validate the functionality of the instrument. It turns out that the velocity of a rising bubble is much more sensitive to adsorbing molecules than classical dynamic surface tension measurements. At very low BLG or surfactant concentrations, for example, the measured local velocity profile of an air bubble is changing dramatically in time scales of seconds while dynamic surface tensions still do not show any measurable changes at this time scale. The solution’s pH and ionic strength are important parameters that govern the measured rising velocity for protein solutions. A general theoretical description of rising bubbles in surfactant and protein solutions is not available at present due to the complex situation of the adsorption process at a bubble surface in a liquid flow field with simultaneous Marangoni effects. However, instead of modelling the complete velocity profile, new theoretical work has been started to evaluate the maximum values in the profile as characteristic parameter for dynamic adsorption layers at the bubble surface more quantitatively. The studies with protein-surfactant mixtures demonstrate in an impressive way that the complexes formed by the two compounds change the surface activity as compared to the original native protein molecules and therefore lead to a completely different retardation behavior of rising bubbles. Changes in the velocity profile can be interpreted qualitatively in terms of increased or decreased surface activity of the formed protein-surfactant complexes. It was also observed that the pH and ionic strength of a protein solution have strong effects on the surface activity of the protein molecules, which however, could be different on the rising bubble velocity and the equilibrium adsorption isotherms. These differences are not fully understood yet but give rise to discussions about the structure of protein adsorption layer under dynamic conditions or in the equilibrium state. The third main stage of the discussed process of fractionation is the formation and characterization of protein foams from BLG solutions at different pH and ionic strength. Of course a minimum BLG concentration is required to form foams. This minimum protein concentration is a function again of solution pH and ionic strength, i.e. of the surface activity of the protein molecules. Although at the isoelectric point, at about pH 5 for BLG, the hydrophobicity and hence the surface activity should be the highest, the concentration and ionic strength effects on the rising velocity profile as well as on the foamability and foam stability do not show a maximum. This is another remarkable argument for the fact that the interfacial structure and behavior of BLG layers under dynamic conditions and at equilibrium are rather different. These differences are probably caused by the time required for BLG molecules to adapt respective conformations once they are adsorbed at the surface. All bubble studies described in this work refer to stages of the foam fractionation process. Experiments with different systems, mainly surfactant and protein solutions, were performed in order to form foams and finally recover a solution representing the foamed material. As foam consists to a large extent of foam lamella – two adsorption layers with a liquid core – the concentration in a foamate taken from foaming experiments should be enriched in the stabilizing molecules. For determining the concentration of the foamate, again the very sensitive bubble rising velocity profile method was applied, which works for any type of surface active materials. This also includes technical surfactants or protein isolates for which an accurate composition is unknown. N2 - Die Fraktionierung ist ein Trennprozess, bei dem verschiedene Materialien auf Grund ihrer Eigenschaften voneinander getrennt werden. Bei der Sedimentation von Teilchen in einer Flüssigkeit dient deren unterschiedliche Dichte zu ihrer Trennung, da schwere Teilchen schneller auf den Boden des Gefäßes sinken als leichtere. Bei der Schaumfraktionierung als Trennprozess dient zur Trennung verschiedener Moleküle in einer Lösung deren Grenzflächenaktivität, d.h. das unterschiedliche Vermögen der Moleküle, sich an der Oberfläche von Gasblasen anzureichern. Durch das Aufsteigen der Blasen in der Flüssigkeit werden daher die Moleküle mit der höheren Grenzflächenaktivität stärker in der Schaumschicht angereichert als die weniger stark grenzflächenaktiven Komponenten. Ziel der vorliegenden Dissertation ist es, den Prozess der Schaumfraktionierung hinsichtlich der Trennung von grenzflächenaktiven Molekülen zu analysieren. Die Bildung von Blasen und deren anschließendes Aufsteigen in der Lösung kann als wichtigstes Element in diesem Prozess angesehen werden. Es ist bekannt, dass die Geschwindigkeit aufsteigender Luftblasen in Wasser eine charakteristische Größe ist, die durch die Anwesenheit grenzflächenaktiver Stoffe (Tenside, Proteine) stark verringert wird. Die vorliegende Dissertation zeigt für das ausgewählte Protein ß-Lactoglobulin und für verschiedene Lebensmittel-Tenside, dass die Messung der Aufstiegsgeschwindigkeit von Luftblasen zur Beurteilung der Anreicherung dieser Moleküle an der Blasenoberfläche ausgezeichnet geeignet ist. Die experimentellen Ergebnisse bei verschiedenen Lösungsbedingungen, wie Konzentration von Protein bzw. Tensid, pH-Wert und Ionenstärke der Lösung, zeigen deutlich, dass die Anreicherung der Proteinmoleküle wesentlich stärker ist als die von Tensiden. Dies gilt auch für Tenside mit einer sehr hohen Grenzflächenaktivität, was im Wesentlichen durch die extrem feste (nahezu irreversible) Anreicherung der Proteinmoleküle zu erklären ist. Die erzielten experimentellen Ergebnisse dienen jetzt als Grundlage für die Weiterentwicklung der Theorie aufsteigender Blasen, die besonders von der Dynamik der Anreicherung der Moleküle geprägt ist. Neueste Untersuchungen haben gezeigt, dass auf der Grundlage dieser experimentellen Ergebnisse erstmals die Geschwindigkeitskonstanten der Anreicherung (Adsorption und Desorption) unabhängig voneinander ermittelt werden können. KW - adsorption KW - air-water interface KW - protein KW - foam KW - rising bubble KW - Adsorption KW - Wasser/Luft Grenzflächen KW - steigende Blasen KW - Schaum KW - Beta-Lactoglobulin Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-94263 ER - TY - THES A1 - Ledendecker, Marc T1 - En route towards advanced catalyst materials for the electrocatalytic water splitting reaction T1 - Innovative Katalysatormaterialien für die elektrokatalytische Wasserspaltung BT - mechanistic insights into the formation of metal carbides, phosphides, sulfides and nitrides BT - mechanistische Einblicke in die Bildung von Metallcarbiden, -phosphiden, -sulfiden und –nitriden N2 - The thesis on hand deals with the development of new types of catalysts based on pristine metals and ceramic materials and their application as catalysts for the electrocatalytic water splitting reaction. In order to breathe life into this technology, cost-efficient, stable and efficient catalysts are imploringly desired. In this manner, the preparation of Mn-, N-, S-, P-, and C-containing nickel materials has been investigated together with the theoretical and electrochemical elucidation of their activity towards the hydrogen (and oxygen) evolution reaction. The Sabatier principle has been used as the principal guideline towards successful tuning of catalytic sites. Furthermore, two pathways have been chosen to ameliorate the electrocatalytic performance, namely, the direct improvement of intrinsic properties through appropriate material selection and secondly the increase of surface area of the catalytic material with an increased amount of active sites. In this manner, bringing materials with optimized hydrogen adsorption free energy onto high surface area support, catalytic performances approaching the golden standards of noble metals were feasible. Despite varying applied synthesis strategies (wet chemistry in organic solvents, ionothermal reaction, gas phase reaction), one goal has been systematically pursued: to understand the driving mechanism of the growth. Moreover, deeper understanding of inherent properties and kinetic parameters of the catalytic materials has been gained. N2 - Wasserstoff ist einer der vielversprechendsten Energieträger aufgrund seiner hohen massenbezogenen Energiedichte. In diesem Zusammenhang erlaubt die elektrokatalytische Wasserspaltung die einfache und saubere Herstellung von Wasserstoff. Allerdings erfordert die Trennung der relativ starken Wasserstoff-Sauerstoff Bindungen beträchtliche Energie und teure Edelmetalle wie Platin oder Iridium zeigen die höchste katalytische Aktivität mit geringer Überspannung und hohen Stromdichten was zu einem guten Wirkungsgrad führt. Aus dieser Motivation heraus befasst sich die vorliegende Arbeit mit der Entwicklung neuer Katalysatoren, die auf Metalllegierungen und Keramiken basieren, sowie ihrer Anwendung für die elektrokatalytische Wasserspaltung. Besonderes Augenmerk wurde auf die Herstellung von kostengünstigen mangan-, stickstoff-, schwefel-, phosphor- und kohlenstoffhaltigen Nickelwerkstoffen gelegt und deren Aktivität experimentell und theoretisch erforscht. Nickel wurde aufgrund seines relativ günstigen Preises und hohen Vorkommens gewählt. Das Prinzip von Sabatier – die Wechselwirkung zwischen Adsorbat und Substrat sollte weder zu stark noch zu schwach sein – wurde als Leitfaden für die Entwicklung effizienter Katalysatoren benutzt. Trotz unterschiedlich angewendeter Synthesestrategien (Synthese in organischen Lösungsmitteln, ionothermale Reaktion oder Gasphasenreaktion), wurde zusätzlich systematisch ein weiteres Ziel verfolgt: Die Wachstums- und Entstehungsmechanismen dieser Materialen zu ergründen. Darüber hinaus wurde ein tieferes Verständnis der inhärenten Eigenschaften und kinetischen Parameter der katalytischen Materialien gewonnen. KW - Wasserspaltung KW - Katalysatoren KW - Keramik KW - Legierungen KW - Materialwissenschaft KW - HER KW - OER KW - water splitting reaction KW - ceramics KW - metal alloys KW - material science KW - HER KW - OER Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-93296 ER - TY - THES A1 - Audörsch, Stephan T1 - Die Synthese von (2Z,4E)-Diencarbonsäureestern und ihre Anwendung in der Totalsynthese von Polyacetylenen T1 - Synthesis of (2Z,4E)-dienoic acid ester and their application in the total synthesis of natural occurring polyacetylenes N2 - Z,E-Diene sind ein häufig auftretendes Strukturmerkmal in Naturstoffen. Aus diesem Grund ist die einfache Darstellung dieser Struktureinheit von großen Interesse in der organischen Chemie. Das erste Ziel der vorliegenden Arbeit war daher die Weiterentwicklung der Ringschlussmetathese-/ baseninduzierten Ringöffnungs-/ Veresterungssequenz (RBRV-Sequenz) zur Synthese von (2Z,4E)-Diencarbonsäureethylestern ausgehend von Butenoaten. Dazu wurde zunächst die RBRV-Sequenz optimiert. Diese aus drei Schritten bestehende Sequenz konnte in einem Eintopf-Verfahren angewendet werden. Die Ringschlussmetathese gelang mit einer Katalysatorbeladung von 1 mol% des GRUBBS-Katalysators der zweiten Generation in Dichlormethan. Für die baseninduzierte Ringöffnung des β,γ-ungesättigten δ Valerolactons wurde NaHMDS verwendet. Die Alkylierung der Carboxylatspezies gelang mit dem MEERWEIN-Reagenz. Die Anwendbarkeit der Sequenz wurde für verschiedene Substrate demonstriert. Die Erweiterung der Methode auf α-substituierte Butenoate unterlag starken Einschränkungen. So konnte der Zugang für α Hydroxyderivate realisiert werden. Bei der Anwendung der RBRV-Sequenz auf die α-substituierten Butenoate wurde festgestellt, dass diese sich nur in moderaten Ausbeuten umsetzen ließen und zudem nicht selektiv zu den (2E,4E)-konfigurierten α-substituierten-Dienestern reagierten. Der Einsatz von Eninen unter den Standardbedingungen der RBRV-Sequenz gelang nicht. Erst nach Modifizierung der Sequenz (höhere Katalysatorbeladung, Wechsel des Lösungsmittels) konnten die [3]Dendralen-Produkte in geringen Ausbeuten erhalten werden. Im zweiten Teil der Arbeit wurde der Einsatz von (2Z,4E)-Diencarbonsäureethylestern in der Totalsynthese von Naturstoffen untersucht. Dazu wurden zunächst die Transformationsmöglichkeiten der Ester geprüft. Es konnte gezeigt werden, dass sich (2Z,4E)-Diencarbonsäureethylester insbesondere zur Synthese von (2Z,4E)-Aldehyden sowie zum Aufbau der (3Z,5E)-Dien-1-in-Struktur eignen. Anhand dieser Ergebnisse wurde im Anschluss die RBRV-Sequenz in der Totalsynthese eingesetzt. Dazu wurde zunächst der (2Z,4E)-Dienester Microsphaerodiolin in seiner ersten Totalsynthese auf drei verschiedene Routen hergestellt. Im Anschluss wurden sechs verschiedene Polyacetylene mit einer (3Z,5E)-Dien-1-in-Einheit hergestellt. Schlüsselschritte in ihrer Synthese waren immer die RBRV-Sequenz zum Aufbau der Z,E-Dien-Einheit, die Transformation des Esters in ein terminales Alkin sowie die CADIOT-CHODKIEWICZ-Kupplung zum Aufbau unsymmetrischer Polyine. Alle sechs Polyacetylene wurden zum ersten Mal in einer Totalsynthese synthetisiert. Drei Polyacetylene wurden ausgehend von (S)-Butantriol enantiomerenrein dargestellt. Anhand ihrer Drehwerte konnte eine Revision der von YAO und Mitarbeitern vorgenommen Zuordnung der Absolutkonfiguration der Naturstoffe vorgenommen werden. N2 - Z,E-Dienes are a common motif in natural products. Therefore their simple preparation is of high interest. The first part of this work focuses on the improvement of the one-pot sequence “RBRV” consisting of three steps: ring closing metathesis, base induced ring opening and esterification of butenoates. This method yields (2Z,4E) dienoic acid esters. As optimized conditions were found the use of Grubbs catalysts 2nd Generation in dichloromethane, NaHMDS as base and Meerwein’s reagent as alkylating agent. The extension of this method on α-substituted butenoates was subject to many restrictions. The synthesis of precursors was realized for α-hydroxy derivates only. Application of these substrates in the RBRV sequence gave the desired products in moderate yield and diminished selectivity. The use of enines was demonstrated as well. For these substrates changes of the conditions were necessary. The products, [3]dendralenes, were obtained in low yield and excellent selectivity. The second part of this thesis focuses on the application of the RBRV-sequence in the total synthesis of natural products with a Z,E-diene unit. For this purpose it was demonstrated how the ester function can be transformed. As result it was shown that especially Z,E-diene-alkynes can be easily synthesized from Z,E-diene esters. Based on these results the RBRV was used in the synthesis of some natural products. These include Microsphaerodiolin, Atractylodemayne A, C and F as well as three other, unnamed, polyacetylenes. All of them have been synthesized for the first time. Three of them were synthesized in enatioselective manner utilizing enantiopure 1,2,4-butane triole as starting material. KW - Polyacetylene KW - Totalsynthese KW - 2Z,4E-Diencarbonsäureester KW - organische Chemie KW - polyacetylenes KW - total synthesis KW - organic chemistry Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-92366 ER - TY - THES A1 - Mai, Tobias T1 - Polymerunterstützte Calciumphosphatmineralisation T1 - Polymer supported calcium phosphate mineralization N2 - Im Verlauf dieser Arbeit sind Blockcopolymere verschiedener Ladung auf Basis von PEO mit hohen Molekulargewichten durch lebendende freie radikalische Polymerisation hergestellt worden. Die Polymere sind einfach im Grammmaßstab herstellbar. Sie zeigen sowohl einen großen Einfluss auf die Nukleation als auch auf die Auflösung von Calciumphosphat. Gleichwohl scheint das Vorhandensein von positiven Gruppen (Kationen, Ampholyten und Betainen) keinen dramatischen Einfluss auf die Nukleation zu haben. So verursachen Polymere mit positiven Ladungen die gleiche Retentionwirkung wie solche, die ausschließlich anionische Gruppen enthalten. Aus der Verwendung der kationischen, ampholytischen und betainischen Copolymere resultiert allerdings eine andersartige Morphologie der Niederschläge, als aus der Verwendung der Anionischen hervorgeht. Bei der Stabilisierung einer HAP-Oberfläche setzt sich dieser Trend fort, das heißt, rein anionische Copolymere wirken stärker stabilisierend als solche, die positive Ladungen enthalten. Durch Inkubation von menschlichem Zahnschmelz mit anionischen Copolymeren konnte gezeigt werden, dass die Biofilmbildung verglichen mit einer unbehandelten Zahnoberfläche eingeschränkt abläuft. All dies macht die Polymere zu interessanten Additiven für Zahnpflegeprodukte. Zusätzlich konnten auf Basis dieser rein anionischen Copolymere Polymerbürsten, ebenfalls über lebendende freie radikalische Polymerisation, hergestellt werden. Diese zeichnen sich durch einen großen Einfluss auf die Kristallphase aus und bilden mit dem CHAP des AB-Types das Material, welches auch in Knochen und Zähnen vorkommt. Erste Cytotoxizitätstests lassen auf das große Potential dieser Polymerbürsten für Beschichtungen in der Medizintechnik schließen. N2 - The thesis at hand describes the preparation of block-copolymers composed of uncharged polyethyleneoxides and differently charged methacrylate-based blocks. Synthesized via living free-radical polymerization the charged blocks were prepared by using of the following monomers: I) for anionic blocks 3-Sulfopropyl methacrylate potassium salt (SPM); II) for cationic blocks 2-(trimethyl ammonium) ethyl methacrylate chloride (TMAEMA) or2-(N-3-Cyanopropyl-N,N-dimethyl ammonium chloride) ethyl methacrylate (CPDMAEMA); III) for betainic blocks [2-(methacryloyloxy) ethyl] dimethyl-(3-sulfopropyl) ammonium hydroxide (MEDSAH) and IV) for ampholytic blocks the anionic SPM and one of the two cationic monomers TMAEMA or CPDMAEMA were used in equal parts. The polymers were accessible in a multigram scale. The resulting block-copolymers show a strong effect on both the dissolution and the nucleation of calcium phosphate. The presence of positively charged moieties in case of applying polycations, polyampholytes and polybetaines does not seem to influence the nucleation in a different manner than the negatively charged polyanions. Nontheless the application of cationic, betainic or ampholytic polymers leads to different morphology of the calcium phosphate precipitates compared to the anionic polymers. The presence of anions results in the formation of spherical well-separated particles whereas cations, ampholytes and betaines cause the composition of smaller particles. In contrast to this data obtained by energy-dispersive X-ray spectroscopy and X-ray crystallography show that calcium deficient hydroxyapatite was formed in all cases. Therefore it can be concluded that the polymers' charge influences the morphology but not the crystal phase. This observation extends to the stabilization of the hydroxyapatite's (HAP) surface. A comparison of polymers containing cations and anionic polymers reveals a stronger stabilizing effect for anions. With the calcium phosphate's dissolution per monomer unit taken into consideration only the anionic charges lead to a stabilization of the HAP-surface at low polymer concentrations while in presence of positive charges a destabilization is observed. By incubating human enamel specimen with mixtures of anionic copolymers and natural human saliva a reduced biofilm formation could be detected when compared to polymer free saliva. Thus the polymers could be potentially used for dental care products. Additionally it was possible to synthesize polymer brushes based on the anionic copolymers' architecture. Again SPM was polymerized yet fastened on a silicon surface via living free-radical polymerization in a grafting-from mechanism. The brushes stand out due to a great influence on the crystal phase of calcium phosphate. They promote the formation of AB-type carbonate substituted hydroxyapatite (CHAP) a material in human bones and teeth that is formed increasingly with age. Initial cytotoxicity tests of both mineralized and unmineralized brushes indicate a high potential of the brushes for biomedical engineering. KW - Polymerchemie KW - polymer chemistry KW - Calciumphosphat KW - calcium phosphate KW - Mineralisation KW - mineralization Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-89056 ER -