TY - THES A1 - Borisova, Dimitriya T1 - Feedback active coatings based on mesoporous silica containers T1 - Rückkopplungsaktive Beschichtungen basierend auf mesoporösen Silika-Behältern N2 - Metalle werden oft während ihrer Anwendung korrosiven Bedingungen ausgesetzt, was ihre Alterungsbeständigkeit reduziert. Deswegen werden korrosionsanfällige Metalle, wie Aluminiumlegierungen mit Schutzbeschichtungen versehen, um den Korrosionsprozess aktiv oder passiv zu verhindern. Die klassischen Schutzbeschichtungen funktionieren als physikalische Barriere zwischen Metall und korrosiver Umgebung und bieten einen passiven Korrosionsschutz nur, wenn sie unbeschädigt sind. Im Gegensatz dazu kann die Korrosion auch im Fall einer Beschädigung mittels aktiver Schutzbeschichtungen gehemmt werden. Chromathaltige Beschichtungen bieten heutzutage den besten aktiven Korrosionsschutz für Aluminiumlegierungen. Aufgrund ihrer Giftigkeit wurden diese weltweit verboten und müssen durch neue umweltfreundliche Schutzbeschichtungen ersetzt werden. Ein potentieller Ersatz sind Schutzbeschichtungen mit integrierten Nano- und Mikrobehältern, die mit ungiftigem Inhibitor gefüllt sind. In dieser Arbeit werden die Entwicklung und Optimierung solcher aktiver Schutzbeschichtungen für die industriell wichtige Aluminiumlegierung AA2024-T3 dargestellt Mesoporöse Silika-Behälter wurden mit dem ungiftigen Inhibitor (2-Mercaptobenzothiazol) beladen und dann in die Matrix anorganischer (SiOx/ZrOx) oder organischer (wasserbasiert) Schichten dispergiert. Zwei Sorten von Silika-Behältern mit unterschiedlichen Größen (d ≈ 80 and 700 nm) wurden verwendet. Diese haben eine große spezifische Oberfläche (≈ 1000 m² g-1), eine enge Porengrößenverteilung mit mittlerer Porenweite ≈ 3 nm und ein großes Porenvolumen (≈ 1 mL g-1). Dank dieser Eigenschaften können große Inhibitormengen im Behälterinneren adsorbiert und gehalten werden. Die Inhibitormoleküle werden bei korrosionsbedingter Erhöhung des pH-Wertes gelöst und freigegeben. Die Konzentration, Position und Größe der integrierten Behälter wurden variiert um die besten Bedingungen für einen optimalen Korrosionsschutz zu bestimmen. Es wurde festgestellt, dass eine gute Korrosionsschutzleistung durch einen Kompromiss zwischen ausreichender Inhibitormenge und guten Barriereeigenschaften hervorgerufen wird. Diese Studie erweitert das Wissen über die wichtigsten Faktoren, die den Korrosionsschutz beeinflussen. Somit wurde die Entwicklung effizienter, aktiver Schutzbeschichtungen ermöglicht, die auf mit Inhibitor beladenen Behältern basieren. N2 - Metals are often used in environments that are conducive to corrosion, which leads to a reduction in their mechanical properties and durability. Coatings are applied to corrosion-prone metals such as aluminum alloys to inhibit the destructive surface process of corrosion in a passive or active way. Standard anticorrosive coatings function as a physical barrier between the material and the corrosive environment and provide passive protection only when intact. In contrast, active protection prevents or slows down corrosion even when the main barrier is damaged. The most effective industrially used active corrosion inhibition for aluminum alloys is provided by chromate conversion coatings. However, their toxicity and worldwide restriction provoke an urgent need for finding environmentally friendly corrosion preventing systems. A promising approach to replace the toxic chromate coatings is to embed particles containing nontoxic inhibitor in a passive coating matrix. This work presents the development and optimization of effective anticorrosive coatings for the industrially important aluminum alloy, AA2024-T3 using this approach. The protective coatings were prepared by dispersing mesoporous silica containers, loaded with the nontoxic corrosion inhibitor 2-mercaptobenzothiazole, in a passive sol-gel (SiOx/ZrOx) or organic water-based layer. Two types of porous silica containers with different sizes (d ≈ 80 and 700 nm, respectively) were investigated. The studied robust containers exhibit high surface area (≈ 1000 m² g-1), narrow pore size distribution (dpore ≈ 3 nm) and large pore volume (≈ 1 mL g-1) as determined by N2 sorption measurements. These properties favored the subsequent adsorption and storage of a relatively large amount of inhibitor as well as its release in response to pH changes induced by the corrosion process. The concentration, position and size of the embedded containers were varied to ascertain the optimum conditions for overall anticorrosion performance. Attaining high anticorrosion efficiency was found to require a compromise between delivering an optimal amount of corrosion inhibitor and preserving the coating barrier properties. This study broadens the knowledge about the main factors influencing the coating anticorrosion efficiency and assists the development of optimum active anticorrosive coatings doped with inhibitor loaded containers. KW - Korrosion KW - Beschichtungen KW - Aluminiumlegierung KW - Silika KW - Nanopartikel KW - mesoporös KW - corrosion KW - coating KW - aluminum alloy KW - silica nanoparticles KW - mesoporous Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-63505 ER - TY - THES A1 - Mbaya Mani, Christian T1 - Functional nanoporous carbon-based materials derived from oxocarbon-metal coordination complexes T1 - Funktionale nanoporöse Kohlenstoffmaterialien auf Basis von Oxokohlenstoff-Metal Koordinationskomplexe N2 - Nanoporous carbon based materials are of particular interest for both science and industry due to their exceptional properties such as a large surface area, high pore volume, high electroconductivity as well as high chemical and thermal stability. Benefiting from these advantageous properties, nanoporous carbons proved to be useful in various energy and environment related applications including energy storage and conversion, catalysis, gas sorption and separation technologies. The synthesis of nanoporous carbons classically involves thermal carbonization of the carbon precursors (e.g. phenolic resins, polyacrylonitrile, poly(vinyl alcohol) etc.) followed by an activation step and/or it makes use of classical hard or soft templates to obtain well-defined porous structures. However, these synthesis strategies are complicated and costly; and make use of hazardous chemicals, hindering their application for large-scale production. Furthermore, control over the carbon materials properties is challenging owing to the relatively unpredictable processes at the high carbonization temperatures. In the present thesis, nanoporous carbon based materials are prepared by the direct heat treatment of crystalline precursor materials with pre-defined properties. This synthesis strategy does not require any additional carbon sources or classical hard- or soft templates. The highly stable and porous crystalline precursors are based on coordination compounds of the squarate and croconate ions with various divalent metal ions including Zn2+, Cu2+, Ni2+, and Co2+, respectively. Here, the structural properties of the crystals can be controlled by the choice of appropriate synthesis conditions such as the crystal aging temperature, the ligand/metal molar ratio, the metal ion, and the organic ligand system. In this context, the coordination of the squarate ions to Zn2+ yields porous 3D cube crystalline particles. The morphology of the cubes can be tuned from densely packed cubes with a smooth surface to cubes with intriguing micrometer-sized openings and voids which evolve on the centers of the low index faces as the crystal aging temperature is raised. By varying the molar ratio, the particle shape can be changed from truncated cubes to perfect cubes with right-angled edges. These crystalline precursors can be easily transformed into the respective carbon based materials by heat treatment at elevated temperatures in a nitrogen atmosphere followed by a facile washing step. The resulting carbons are obtained in good yields and possess a hierarchical pore structure with well-organized and interconnected micro-, meso- and macropores. Moreover, high surface areas and large pore volumes of up to 1957 m2 g-1 and 2.31 cm3 g-1 are achieved, respectively, whereby the macroscopic structure of the precursors is preserved throughout the whole synthesis procedure. Owing to these advantageous properties, the resulting carbon based materials represent promising supercapacitor electrode materials for energy storage applications. This is exemplarily demonstrated by employing the 3D hierarchical porous carbon cubes derived from squarate-zinc coordination compounds as electrode material showing a specific capacitance of 133 F g-1 in H2SO4 at a scan rate of 5 mV s-1 and retaining 67% of this specific capacitance when the scan rate is increased to 200 mV s-1. In a further application, the porous carbon cubes derived from squarate-zinc coordination compounds are used as high surface area support material and decorated with nickel nanoparticles via an incipient wetness impregnation. The resulting composite material combines a high surface area, a hierarchical pore structure with high functionality and well-accessible pores. Moreover, owing to their regular micro-cube shape, they allow for a good packing of a fixed-bed flow reactor along with high column efficiency and a minimized pressure drop throughout the packed reactor. Therefore, the composite is employed as heterogeneous catalyst in the selective hydrogenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran showing good catalytic performance and overcoming the conventional problem of column blocking. Thinking about the rational design of 3D carbon geometries, the functions and properties of the resulting carbon-based materials can be further expanded by the rational introduction of heteroatoms (e.g. N, B, S, P, etc.) into the carbon structures in order to alter properties such as wettability, surface polarity as well as the electrochemical landscape. In this context, the use of crystalline materials based on oxocarbon-metal ion complexes can open a platform of highly functional materials for all processes that involve surface processes. N2 - Nanoporöse Kohlenstoffmaterialien zeichnen sich u. a. durch ihre außergewöhnlichen Eigenschaften aus wie z. B. hohe Oberfläche, hohes Porenvolumen, hohe elektrische Leitfähigkeit und auch hohe chemische und thermische Stabilität. Aufgrund dessen finden sie Anwendung in den unterschiedlichsten Bereichen von der Speicherung elektrischer Energie bis hin zur Katalyse und Gasspeicherung. Die klassische Synthese von porösen Kohlenstoffmaterialien basiert u. a. auf der Nutzung von sogenannten anorganischen bzw. organischen Templaten und/oder chemischen Aktivierungsagenzien. Allerdings gelten diese Methoden eher als kompliziert, kostspielig und umweltschädlich. Außerdem wird eine gezielte Kontrolle der Produkteigenschaften durch die zahlreichen Prozesse erschwert, die sich bei den hohen Karbonisierungstemperaturen abspielen und folglich die Materialeigenschaften unvorhersehbar verändern können. In der vorliegenden Arbeit wird ein alternatives Konzept für die Synthese von nanoporösen Kohlenstoffmaterialien mit gezielt einstellbaren Eigenschaften vorgestellt. Diese basiert auf der Nutzung von kristallinen Vorläufermaterialien, die aus der Koordination von den Anionen der Quadratsäure bzw. der Krokonsäure mit verschiedenen Metallionen (Zn2+, Cu2+, Ni2+ und Co2+) resultieren. Diese haben den Vorteil, dass Eigenschaften wie z. B. die Partikelmorphologie und Porosität gezielt durch die Wahl geeigneter Syntheseparameter (z. B. Temperatur, molares Verhältnis, Metallion und Ligand) eingestellt werden können. Beispielsweise führen Koordinationskomplexe von der Quadratsäure mit Zn2+ in Wasser zu porösen 3D würfelförmigen Mikrokristallen, die durch einfache thermische Behandlung unter Schutzgasatmosphäre zu den entsprechenden Kompositen umgewandelt werden. Ein anschließender Waschschritt führt zu den entsprechenden Kohlenstoffmaterialien unter Erhalt der makroskopischen Struktur der kristallinen Vorläufermaterialien. In diesem Zusammenhang weisen die resultierenden Kohlenstoffe ebenfalls eine 3D Würfelform mit einer hierarchischen Porenstruktur bestehend aus vernetzten Mikro-, Meso- und Makroporen auf. Ferner besitzen die Kohlenstoffe hohe Oberflächen und Porenvolumen von bis zu 1.957 m2 g-1 bzw. 2,31 cm3 g-1. Um die Vorteile dieser Eigenschaften zu demonstrieren, werden sie als Elektrodenmaterial für Superkondensatoren getestet und zeigen dabei vielversprechende Kapazitäten. Außerdem, werden sie auch als Trägermaterial für die Immobilisierung von Nickel-Nanopartikel verwendet und als heterogene Katalysatoren in der selektiven Hydrierung von 5-hydroxymethylfurfural zu 2,5-dimethylfuran in einem Festbettreaktor eingesetzt. Dabei wird eine gute Katalysatorleistung (Produktivität) bei minimalem Druckabfall in der Reaktorsäule erreicht. KW - squaric acid KW - Quadratsäure KW - mesocrystals KW - Mesokristalle KW - nanoporöser Kohlenstoffpartikel KW - nanoporous carbon particles KW - Nanopartikel KW - nanoparticles KW - Koordinationskomplexe KW - coordination complexes KW - oxocarbon KW - Oxo-Kohlenstoff Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-407866 ER - TY - THES A1 - Schulze, Nicole T1 - Neue Templatphasen zur anisotropen Goldnanopartikelherstellung durch den Einsatz strukturbildender Polymere T1 - New template phases for anisotropic gold nanoparticle production through the use of structure-forming polymers N2 - Ziel der vorliegenden Arbeit war die Synthese und Charakterisierung von anisotropen Goldnanopartikeln in einer geeigneten Polyelektrolyt-modifizierten Templatphase. Der Mittelpunkt bildet dabei die Auswahl einer geeigneten Templatphase, zur Synthese von einheitlichen und reproduzierbaren anisotropen Goldnanopartikeln mit den daraus resultierenden besonderen Eigenschaften. Bei der Synthese der anisotropen Goldnanopartikeln lag der Fokus in der Verwendung von Vesikeln als Templatphase, wobei hier der Einfluss unterschiedlicher strukturbildender Polymere (stark alternierende Maleamid-Copolymere PalH, PalPh, PalPhCarb und PalPhBisCarb mit verschiedener Konformation) und Tenside (SDS, AOT – anionische Tenside) bei verschiedenen Synthese- und Abtrennungsbedingungen untersucht werden sollte. Im ersten Teil der Arbeit konnte gezeigt werden, dass PalPhBisCarb bei einem pH-Wert von 9 die Bedingungen eines Röhrenbildners für eine morphologische Transformation von einer vesikulären Phase in eine röhrenförmige Netzwerkstruktur erfüllt und somit als Templatphase zur formgesteuerten Bildung von Nanopartikeln genutzt werden kann. Im zweiten Teil der Arbeit wurde dargelegt, dass die Templatphase PalPhBisCarb (pH-Wert von 9, Konzentration von 0,01 wt.%) mit AOT als Tensid und PL90G als Phospholipid (im Verhältnis 1:1) die effektivste Wahl einer Templatphase für die Bildung von anisotropen Strukturen in einem einstufigen Prozess darstellt. Bei einer konstanten Synthesetemperatur von 45 °C wurden die besten Ergebnisse bei einer Goldchloridkonzentration von 2 mM, einem Gold-Templat-Verhältnis von 3:1 und einer Synthesezeit von 30 Minuten erzielt. Ausbeute an anisotropen Strukturen lag bei 52 % (Anteil an dreieckigen Nanoplättchen von 19 %). Durch Erhöhung der Synthesetemperatur konnte die Ausbeute auf 56 % (29 %) erhöht werden. Im dritten Teil konnte durch zeitabhängige Untersuchungen gezeigt werden, dass bei Vorhandensein von PalPhBisCarb die Bildung der energetisch nicht bevorzugten Plättchen-Strukturen bei Raumtemperatur initiiert wird und bei 45 °C ein Optimum annimmt. Kintetische Untersuchungen haben gezeigt, dass die Bildung dreieckiger Nanoplättchen bei schrittweiser Zugabe der Goldchlorid-Präkursorlösung zur PalPhBisCarb enthaltenden Templatphase durch die Dosierrate der vesikulären Templatphase gesteuert werden kann. In umgekehrter Weise findet bei Zugabe der Templatphase zur Goldchlorid-Präkursorlösung bei 45 °C ein ähnlicher, kinetisch gesteuerter Prozess der Bildung von Nanodreiecken statt mit einer maximalen Ausbeute dreieckigen Nanoplättchen von 29 %. Im letzten Kapitel erfolgten erste Versuche zur Abtrennung dreieckiger Nanoplättchen von den übrigen Geometrien der gemischten Nanopartikellösung mittels tensidinduzierter Verarmungsfällung. Bei Verwendung von AOT mit einer Konzentration von 0,015 M wurde eine Ausbeute an Nanoplättchen von 99 %, wovon 72 % dreieckiger Geometrien hatten, erreicht. N2 - The aim of the present work was the synthesis and characterization of anisotropic gold nanoparticles in a suitable polyelectrolyte-modified template phase. The focus was on the selection of a suitable template phase for the synthesis of uniform and reproducible anisotropic gold nanoparticles with the resulting special properties. In the synthesis of the anisotropic gold nanoparticles, the focus was on the use of vesicles as a template phase. Here, the influence of different structure-forming polymers (strongly alternating maleimide copolymers PalH, PalPh, PalPhCarb and PalPhBisCarb with different conformations) and surfactants (SDS, AOT - anionic surfactants) should be studied at various synthesis and separation conditions. In the first part of the work, it could be shown that PalPhBisCarb at pH 9 meets the requirements of a tubulating agent for a morphological transformation of a vesicular phase into a tubular network structure and thus can be used as a template phase for the shape-controlled formation of nanoparticles. In the second part of the work, it was shown that the template phase PalPhBisCarb (pH value of 9, concentration of 0.01 wt.%) with AOT as surfactant and PL90G as phospholipid (in the ratio 1:1) is the most effective choice of template phase for the formation of anisotropic structures in a one-step process. At a constant synthesis temperature of 45 °C, the best results were achieved with a gold chloride concentration of 2 mM, a gold-template ratio of 3:1 and a synthesis time of 30 minutes. The yield of anisotropic structures was 52% (triangular nanoplatelet content of 19%). By increasing the synthesis temperature, the yield could be increased to 56% (29%). In the third part, it was shown by time-dependent investigations that in the presence of PalPhBisCarb, the formation of the not energetically preferred platelet structures is initiated at room temperature and assumes an optimum at 45 °C. Kinetical studies have shown that the formation of triangular nanosheets can be controlled by the dosing rate of the vesicular template phase when the gold chloride precursor solution is gradually added to the PalPhBisCarb-containing template phase. Conversely, upon addition of the template phase to the gold chloride precursor solution at 45 °C, a similar, kinetically controlled process of formation of nanodimers takes place with a maximum yield of triangular nanoplatelets of 29%. In the last chapter, initial attempts were made to separate triangular nanoplatelets from the other geometries of the mixed nanoparticle solution by means of surfactant-induced depletion flocculation. When AOT was used at a concentration of 0.015 M, a yield of nanoplatelets of 99%, of which 72% had triangular geometries, was achieved. KW - Nanopartikel KW - nanoparticle KW - Templatphase KW - template phase KW - Gold KW - gold KW - anisotrop KW - anisotropic Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-409515 ER - TY - THES A1 - Popovic, Jelena T1 - Novel lithium iron phosphate materials for lithium-ion batteries T1 - Neuartige Lithium-Eisen-Phosphat-Materialien für Lithium-Ionen-Batterien N2 - Conventional energy sources are diminishing and non-renewable, take million years to form and cause environmental degradation. In the 21st century, we have to aim at achieving sustainable, environmentally friendly and cheap energy supply by employing renewable energy technologies associated with portable energy storage devices. Lithium-ion batteries can repeatedly generate clean energy from stored materials and convert reversely electric into chemical energy. The performance of lithium-ion batteries depends intimately on the properties of their materials. Presently used battery electrodes are expensive to be produced; they offer limited energy storage possibility and are unsafe to be used in larger dimensions restraining the diversity of application, especially in hybrid electric vehicles (HEVs) and electric vehicles (EVs). This thesis presents a major progress in the development of LiFePO4 as a cathode material for lithium-ion batteries. Using simple procedure, a completely novel morphology has been synthesized (mesocrystals of LiFePO4) and excellent electrochemical behavior was recorded (nanostructured LiFePO4). The newly developed reactions for synthesis of LiFePO4 are single-step processes and are taking place in an autoclave at significantly lower temperature (200 deg. C) compared to the conventional solid-state method (multi-step and up to 800 deg. C). The use of inexpensive environmentally benign precursors offers a green manufacturing approach for a large scale production. These newly developed experimental procedures can also be extended to other phospho-olivine materials, such as LiCoPO4 and LiMnPO4. The material with the best electrochemical behavior (nanostructured LiFePO4 with carbon coating) was able to delive a stable 94% of the theoretically known capacity. N2 - Konventionelle Energiequellen sind weder nachwachsend und daher nachhaltig nutzbar, noch weiterhin langfristig verfügbar. Sie benötigen Millionen von Jahren um gebildet zu werden und verursachen in ihrer Nutzung negative Umwelteinflüsse wie starke Treibhausgasemissionen. Im 21sten Jahrhundert ist es unser Ziel nachhaltige und umweltfreundliche, sowie möglichst preisgünstige Energiequellen zu erschließen und nutzen. Neuartige Technologien assoziiert mit transportablen Energiespeichersystemen spielen dabei in unserer mobilen Welt eine große Rolle. Li-Ionen Batterien sind in der Lage wiederholt Energie aus entsprechenden Prozessen nutzbar zu machen, indem sie reversibel chemische in elektrische Energie umwandeln. Die Leistung von Li-Ionen Batterien hängen sehr stark von den verwendeten Funktionsmaterialien ab. Aktuell verwendete Elektrodenmaterialien haben hohe Produktionskosten, verfügen über limitierte Energiespeichekapazitäten und sind teilweise gefährlich in der Nutzung für größere Bauteile. Dies beschränkt die Anwendungsmöglichkeiten der Technologie insbesondere im Gebiet der hybriden Fahrzeugantriebe. Die vorliegende Dissertation beschreibt bedeutende Fortschritte in der Entwicklung von LiFePO4 als Kathodenmaterial für Li-Ionen Batterien. Mithilfe einfacher Syntheseprozeduren konnten eine vollkommen neue Morphologie (mesokristallines LiFePo4) sowie ein nanostrukturiertes Material mit exzellenten elektrochemischen Eigenschaften hergestellt werden. Die neu entwickelten Verfahren zur Synthese von LiFePo4 sind einschrittig und bei signifikant niedrigeren Temperaturen im Vergleich zu konventionellen Methoden. Die Verwendung von preisgünstigen und umweltfreundlichen Ausgangsstoffen stellt einen grünen Herstellungsweg für die large scale Synthese dar. Mittels des neuen Synthesekonzepts konnte meso- und nanostrukturiertes LiFe PO4 generiert werden. Die Methode ist allerdings auch auf andere phospho-olivin Materialien (LiCoPO4, LiMnPO4) anwendbar. Batterietests der besten Materialien (nanostrukturiertes LiFePO4 mit Kohlenstoffnanobeschichtung) ergeben eine mögliche Energiespeicherung von 94%. KW - Li-Ionen-Akkus KW - Kathode KW - LiFePO4 KW - Mesokristalle KW - Nanopartikel KW - Li-ion batteries KW - cathode KW - LiFePO4 KW - mesocrystals KW - nanoparticles Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-54591 ER -