TY - JOUR A1 - Yang, X. H. A1 - Jaiser, Frank A1 - Klinger, S A1 - Neher, Dieter T1 - Blue polymer electrophosphorescent devices with different electron-transporting oxadiazoles N2 - We report that the performances of blue polymer electrophosphorescent devices are crucially depending on the choice of the electron transporting material incorporated into the emissive layer. Devices with 1,3-bis[(4-tert- butylphenyl)-1,3,4-oxidiazolyl]phenylene (OXD-7) doped at similar to 40 wt% into a poly(vinylcarbazole) matrix exhibited significantly higher efficiencies than those with 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD), yielding maximum luminous and power efficiency values of 18.2 Cd/A and 8.8 lm/W, respectively. Time resolved photoluminescence measurements revealed a long lifetime phosphorescence component in layers with PBD, which we assign to significant triplet harvesting by this electron-transporting component. (c) 2006 American Institute of Physics Y1 - 2006 UR - http://scitation.aip.org/getpdf/servlet/ GetPDFServlet?filetype=pdf&id=APPLAB000088000002021107000001&idtype=cvips&doi=10.1063/1.2162693&prog=normal U6 - https://doi.org/10.1063/1.2162693 ER - TY - JOUR A1 - Li, Tian-yi A1 - Benduhn, Johannes A1 - Li, Yue A1 - Jaiser, Frank A1 - Spoltore, Donato A1 - Zeika, Olaf A1 - Ma, Zaifei A1 - Neher, Dieter A1 - Vandewal, Koen A1 - Leo, Karl T1 - Boron dipyrromethene (BODIPY) with meso-perfluorinated alkyl substituents as near infrared donors in organic solar cells JF - Journal of materials chemistry : A, Materials for energy and sustainability N2 - Three furan-fused BODIPYs were synthesized with perfluorinated methyl, ethyl and n-propyl groups on the meso-carbon. They were obtained with high yields by reacting the furan-fused 2-carboxylpyrrole in corresponding perfluorinated acid and anhydride. With the increase in perfluorinated alkyl chain length, the molecular packing in the single crystal is influenced, showing increasing stacking distance and decreasing slope angle. All the BODIPYs were characterized as intense absorbers in near infrared region in solid state, peaking at similar to 800 nm with absorption coefficient of over 280 000 cm(-1). Facilitated by high thermal stability, the furan-fused BODIPYs were employed in vacuum-deposited organic solar cells as electron donors. All devices exhibit PCE over 6.0% with the EQE maximum reaching 70% at similar to 790 nm. The chemical modification of the BODIPY donors have certain influence on the active layer morphology, and the highest PCE of 6.4% was obtained with a notably high jsc of 13.6 mA cm(-2). Sensitive EQE and electroluminance studies indicated that the energy losses generated by the formation of a charge transfer state and the radiative recombination at the donor-acceptor interface were comparable in the range of 0.14-0.19 V, while non-radiative recombination energy loss of 0.38 V was the main energy loss route resulting in the moderate V-oc of 0.76 V. Y1 - 2018 U6 - https://doi.org/10.1039/c8ta06261g SN - 2050-7488 SN - 2050-7496 VL - 6 IS - 38 SP - 18583 EP - 18591 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Steyrleuthner, Robert A1 - Schubert, Marcel A1 - Jaiser, Frank A1 - Blakesley, James C. A1 - Chen, Zhihua A1 - Facchetti, Antonio A1 - Neher, Dieter T1 - Bulk electron transport and charge injection in a high mobility n-type semiconducting polymer N2 - Bulk electron transport in a high mobility n-type polymer is studied by time-of-flight photocurrent measurements and electron-only devices. Bulk electron mobilities of similar to 5 x 10(-3) cm(2)/Vs are obtained. The analysis of the electron currents suggests the presence of an injection barrier for all conventionally used low workfunction cathodes. Y1 - 2010 UR - http://www3.interscience.wiley.com/cgi-bin/jhome/10008336 U6 - https://doi.org/10.1002/adma.201000232 SN - 0935-9648 ER - TY - JOUR A1 - Qu, J. Q. A1 - Zhang, J. Y. A1 - Grimsdale, A. C. A1 - Mullen, K. A1 - Jaiser, Frank A1 - Yang, X. H. A1 - Neher, Dieter T1 - Dendronized perylene diimide emitters : Synthesis, luminescence, and electron and energy transfer studies N2 - Aggregation of chromophores in the solid state commonly causes undesirable red shifts in the emission spectra and/or emission quenching. To overcome this problem, we have prepared soluble perylenetetracarboxidiimide dyes in which the chromophores are effectively shielded by polyphenylene dendrimers attached in the bay positions. Models show that attachment of the shielding units in the bay position should provide more efficient shielding than attaching them via the imide moieties. The dendrimers possess excellent film-forming properties due to alkyl substituents on their peripheries. The lack of a red shift in emission upon going from solution to the solid state indicates the dendrons suppress interaction of the emissive cores, leading to pure red-orange emission. Single-layer LEDs produce red-orange emission with relatively low efficiency especially for the higher generation dendrons, which is attributed to poor charge conduction. LEDs using blends of the dendrimers and the undendronized dye as a model compound in PVK have been investigated, and a model to extract relative charge injection rates through the dendritic scaffold from the spectral contributions in the EL spectra is developed Y1 - 2004 SN - 0024-9297 ER - TY - JOUR A1 - Li, Tian-yi A1 - Benduhn, Johannes A1 - Qiao, Zhi A1 - Liu, Yuan A1 - Li, Yue A1 - Shivhare, Rishi A1 - Jaiser, Frank A1 - Wang, Pei A1 - Ma, Jie A1 - Zeika, Olaf A1 - Neher, Dieter A1 - Mannsfeld, Stefan C. B. A1 - Ma, Zaifei A1 - Vandewal, Koen A1 - Leo, Karl T1 - Effect of H- and J-Aggregation on the Photophysical and Voltage Loss of Boron Dipyrromethene Small Molecules in Vacuum-Deposited Organic Solar Cells JF - The journal of physical chemistry letters N2 - An understanding of the factors limiting the open-circuit voltage (V-oc) and related photon energy loss mechanisms is critical to increase the power conversion efficiency (PCE) of small-molecule organic solar cells (OSCs), especially those with near-infrared (NIR) absorbers. In this work, two NIR boron dipyrromethene (BODIPY) molecules are characterized for application in planar (PHJ) and bulk (BHJ) heterojunction OSCs. When two H atoms are substituted by F atoms on the peripheral phenyl rings of the molecules, the molecular aggregation type in the thin film changes from the H-type to J-type. For PHJ devices, the nonradiative voltage loss of 0.35 V in the J-aggregated BODIPY is lower than that of 0.49 V in the H-aggregated device. In BHJ devices with a nonradiative voltage loss of 0.35 V, a PCE of 5.5% is achieved with an external quantum efficiency (EQE) maximum of 68% at 700 nm. Y1 - 2019 U6 - https://doi.org/10.1021/acs.jpclett.9b01222 SN - 1948-7185 VL - 10 IS - 11 SP - 2684 EP - 2691 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Zen, Achmad A1 - Pflaum, J. A1 - Hirschmann, S. A1 - Zhuang, W. A1 - Jaiser, Frank A1 - Asawapirom, Udom A1 - Rabe, J. P. A1 - Scherf, Ullrich A1 - Neher, Dieter T1 - Effect of molecular weight and annealing of poly (3-hexylthiophene)s on the performance of organic field-effect transistors N2 - The optical, structural, and electrical properties of thin layers made from poly(3-hexylthiophene) (P3HT) samples of different molecular weights are presented. As reported in a previous paper by Kline et al., Adv. Mater 2003, 15, 1519, the mobilities of these layers are a strong function of the molecular weight, with the largest mobility found for the largest molecular weight. Atomic force microscopy studies reveal a complex polycrystalline morphology which changes considerably upon annealing. X-ray studies show the occurrence of a layered phase for all P3HT fractions, especially after annealing at 1.50 degreesC . However, there is no clear correlation between the differences in the transport properties and the data from structural investigations. In order to reveal the processes limiting the mobility in these layers, the transistor properties were investigated as a function of temperature. The mobility decreases continuously with increasing temperatures; with the same trend pronounced thermochromic effects of the P3HT films occur. Apparently, the polymer chains adopt a more twisted, disordered conformation at higher temperatures, leading to interchain transport barriers. We conclude that the backbone conformation of the majority of the bulk material rather than the crystallinity of the layer is the most crucial parameter controlling the charge transport in these P3HT layers. This interpretation is supported by the significant blue-shift of the solid-state absorption spectra with decreasing molecular weight, which is indicative of a larger distortion of the P3HT backbone in the low-molecular weight P3HT layers Y1 - 2004 ER - TY - JOUR A1 - Yang, Xiao Hui A1 - Jaiser, Frank A1 - Stiller, Burkhard A1 - Neher, Dieter A1 - Galbrecht, Frank A1 - Scherf, Ullrich T1 - Efficient polymer electrophosphoreseent devices with interfacial layers JF - Advanced functional materials N2 - It is shown that several polymers can form insoluble interfacial layers on a poly (ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) layer after annealing of the double-layer structure. The thickness of the interlayer is dependent on the characteristics of the underlying PEDOT.PSS and the molecular weight of the polymers. It is further shown that the electronic structures of the interlayer polymers have a significant effect on the properties of red-light-emitting polymer-based electrophosphorescent devices. Upon increasing the highest occupied molecular orbital and lowest unoccupied molecular orbital positions, a significant increase in current density and device efficiency is observed. This is attributed to efficient blocking of electrons in combination with direct injection of holes from the interlayer to the phosphorescent dye. Upon proper choice of the interlayer polymer, efficient red, polymer-based electrophosphorescent devices with a peak luminance efficiency of 5.5 cd A(-1) (external quantum efficiency = 6 %) and a maximum power-conversion efficiency of 5 Im W-1 can be realized. Y1 - 2006 U6 - https://doi.org/10.1002/adfm.200500834 SN - 1616-301X SN - 1616-3028 VL - 16 IS - 16 SP - 2156 EP - 2162 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Al-Sa'di, Mahmoud A1 - Jaiser, Frank A1 - Bagnich, Sergey A. A1 - Unger, Thomas A1 - Blakesley, James C. A1 - Wilke, Andreas A1 - Neher, Dieter T1 - Electrical and optical simulations of a polymer-based phosphorescent organic light-emitting diode with high efficiency JF - Journal of polymer science : B, Polymer physics N2 - A comprehensive numerical device simulation of the electrical and optical characteristics accompanied with experimental measurements of a new highly efficient system for polymer-based light-emitting diodes doped with phosphorescent dyes is presented. The system under investigation comprises an electron transporter attached to a polymer backbone blended with an electronically inert small molecule and an iridium-based green phosphorescent dye which serves as both emitter and hole transporter. The device simulation combines an electrical and an optical model. Based on the known highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels of all components as well as the measured electrical and optical characteristics of the devices, we model the emissive layer as an effective medium using the dye's HOMO as hole transport level and the polymer LUMO as electron transport level. By fine-tuning the injection barriers at the electron and hole-injecting contact, respectively, in simulated devices, unipolar device characteristics were fitted to the experimental data. Simulations using the so-obtained set of parameters yielded very good agreement to the measured currentvoltage, luminancevoltage characteristics, and the emission profile of entire bipolar light-emitting diodes, without additional fitting parameters. The simulation was used to gain insight into the physical processes and the mechanisms governing the efficiency of the organic light-emitting diode, including the position and extent of the recombination zone, carrier concentration profiles, and field distribution inside the device. The simulations show that the device is severely limited by hole injection, and that a reduction of the hole-injection barrier would improve the device efficiency by almost 50%. KW - conjugated polymers KW - high performance polymers KW - organic electronics KW - organic light-emitting diode KW - simulations KW - TCAD Y1 - 2012 U6 - https://doi.org/10.1002/polb.23158 SN - 0887-6266 VL - 50 IS - 22 SP - 1567 EP - 1576 PB - Wiley-Blackwell CY - Hoboken ER - TY - JOUR A1 - Hoffmann, Sebastian T. A1 - Jaiser, Frank A1 - Hayer, Anna A1 - Baessler, Heinz A1 - Unger, Thomas A1 - Athanasopoulos, Stavros A1 - Neher, Dieter A1 - Koehler, Anna T1 - How Do Disorder, Reorganization, and Localization Influence the Hole Mobility in Conjugated Copolymers? JF - JOURNAL OF THE AMERICAN CHEMICAL SOCIETY N2 - In order to unravel the intricate interplay between disorder effects, molecular reorganization, and charge carrier localization, a comprehensive study was conducted on hole transport in a series of conjugated alternating phenanthrene indenofluorene copolymers. Each polymer in the series contained one further comonomer comprising monoamines, diamines, or amine-free structures, whose influence on the electronic, optical, and charge transport properties was studied. The series covered a wide range of highest occupied molecular orbital (HOMO) energies as determined by cyclovoltammetry. The mobility, inferred from time-of-flight (ToF) experiments as a function of temperature and electric field, was found to depend exponentially on the HOMO energy. Since possible origins for this effect include energetic disorder, polaronic effects, and wave function localization, the relevant parameters were determined using a range of methods. Disorder and molecular reorganization were established first by an analysis of absorption and emission measurements and second by an analysis of the ToF measurements. In addition, density functional theory calculations were carried out to determine how localized or delocalized holes on a polymer chain are and to compare calculated reorganization energies with those that have been inferred from optical spectra. In summary, we conclude that molecular reorganization has little effect on the hole mobility in this system while both disorder effects and hole localization in systems with low-lying HOMOs are predominant. In particular, as the energetic disorder is comparable for the copolymers, the absolute value of the hole mobility at room temperature is determined by the hole localization associated with the triarylamine moieties. Y1 - 2013 U6 - https://doi.org/10.1021/ja308820j SN - 0002-7863 VL - 135 IS - 5 SP - 1772 EP - 1782 PB - AMER CHEMICAL SOC CY - WASHINGTON ER - TY - THES A1 - Jaiser, Frank T1 - Ladungsträger- und Anregungsdynamik in halbleitenden Polymerschichten mit eingemischten Emittern und Ladungsträgerfallen T1 - Charge and excitation dynamics in semiconducting polymer layers doped with emitters and charge carrier traps N2 - In Leuchtdioden wird Licht durch die Rekombination von injizierten Ladungsträgern erzeugt. Das kann einerseits in anorganischen Materialien geschehen. In diesem Fall ist es notwendig, hochgeordnete Kristallstrukturen herzustellen, die die Eigenschaften der Leuchtdioden bestimmen. Ein anderer Ansatz ist die Verwendung von organischen Molekülen und Polymeren. Auf Grund der Vielseitigkeit der organischen Chemie können die Eigenschaften der verwendeten halbleitenden Polymere schon während der Synthese beeinflusst werden. Außerdem weisen auch diese Polymere die bekannte mechanische Flexibilität auf. Die Herstellung von flexiblen, großflächigen Beleuchtungsquellen und Anzeigelementen ist so möglich. Die erste Leuchtdiode mit einem halbleitenden Polymer als Emitter wurde 1990 hergestellt. Seither hat das Forschungsgebiet eine rasante Entwicklung genommen. Auch erste kommerzielle Produkte sind erhältlich. Im Zuge dieser Entwicklung wurde deutlich, dass die Eigenschaften von polymeren Leuchtdioden – beispielsweise Farbe und Effizienz – durch die Verwendung mehrerer Komponenten in der aktiven Schicht deutlich verbessert werden können. Gleichzeitig ergeben sich neue Herausforderungen durch die Wechselwirkungen der verschiedenen Filmbestandteile. Während die Komponenten oft entweder zur Verbesserung des Ladungstransportes oder zur Beeinflussung der Emission zugegeben werden, muss darauf geachtet werden, dass die anderen Prozesse nicht negativ beeinflusst werden. In dieser Arbeit werden einige dieser Wechselwirkungen untersucht und mit einfachen physikalischen Modellen erklärt. So werden zunächst blau emittierende Leuchtdioden auf der Basis von Polyfluoren untersucht. Dieses Material ist zwar ein sehr effizienter blauer Emitter, jedoch ist es anfällig für chemische Defekte, diese sich nicht vollständig verhindern lassen. Die Defekte bilden Fallenzustände für Elektronen, ihr Einfluss lässt sich durch die Zugabe von Lochfallen unterdrücken. Der zugrunde liegende Prozess, die Beeinflussung der Ladungsträgerbalance, wird erklärt. Im Folgenden werden Mischsystemen mit dendronisierten Emittern, die gleichzeitig eine Falle für Elektronen bilden, untersucht. Hier wird die unterschiedliche Wirkung der isolierenden Hülle auf die Ladungs- und Energieübertragung zwischen Matrix und Farbstoffkern der Dendrimere untersucht. In Mischsystemen haben die Natur der angeregten Zustände sowie die Art und Weise des Ladungsträgertransportes einen großen Einfluss auf diese Transferprozesse. Außerden hat auch hier die Ladungsträgerbalance Auswirkungen auf die Emission. Um den Ladungsträgereinfang in Fallenzuständen zu charakterisieren, wird eine Methode auf Grundlage der Messung des zeitaufgelösten Photostroms in organischen Mischfilmen weiterentwickelt. Die erzielten Ergebnisse zeigen, dass die Übertragung der für geordnete Systeme entwickelten Modelle des Ladungsträgertransportes nicht ohne weiteres auf Polymersysteme mit hoher Unordnung übertragen werden können. Abschließend werden zeitaufgelöste Messungen der Phosphoreszenz in entsprechenden Mischungen aus Polymeren und organometallischen Verbindungen vorgestellt. Auch diese Systeme enthalten üblicherweise weitere Komponenten, die den Ladungstransport verbessern. In diesen Filmen kann es zu einer Übertragung der Tripletts vom Emitter auf die weiteren Filmbestandteile kommen. Bei Kenntnis der in Frage kommenden Wechselwirkungen können die unerwünschten Prozesse vermieden werden. N2 - Light-emitting diodes generate light from the recombination of injected charge carriers. This can be obtained in inorganic materials. Here, it is necessary to produce highly ordered crystalline structures that determine the properties of the device. Another possibility is the utilization of organic molecules and polymers. Based on the versatile organic chemistry, it is possible to tune the properties of the semiconducting polymers already during synthesis. In addition, semiconducting polymers are mechanically flexible. Thus, it is possible to construct flexible, large-area light sources and displays. The first light-emitting diode using a polymer emitter was presented in 1990. Since then, this field of research has grown rapidly up to the point where first products are commercially available. It has become clear that the properties of polymer light-emitting diodes such as color and efficiency can be improved by incorporating multiple components inside the active layer. At the same time, this gives rise to new interactions between these components. While components are often added either to improve the charge transport or to change the emission, it has to made sure that other processes are not influenced in a negative manner. This work investigates some of these interactions and describes them with simple physical models. First, blue light-emitting diodes based on polyfluorene are analyzed. This polymer is an efficient emitter, but it is susceptible to the formation of chemical defects that can not be suppressed completely. These defects form electron traps, but their effect can be compensated by the addition of hole traps. The underlying process, namely the changed charge carrier balance, is explained. In the following, blend systems with dendronized emitters that form electron traps are investigated. The different influence of the insulating shell on the charge and energy transfer between polymer host and the emissive core of the dendrimers is examined. In the blend, the nature of the excited states as well as the method of the charge transport through the layer are of great importance to the transfer. Again, the charge carrier balance influences the emission. To characterize the trapping of charges in trap states, a method based on the measurement of transient photocurrents is enhanced. The results show that models developed for ordered systems can not simply be transferred to polymer systems with a high degree of disorder. Finally, time-resolved measurements of the phosphorescence decay in blends of polymers with organo-metallic compounds are shown. Usually, these systems contain more components that facilitate charge transport. Thus, triplets may be transferred from the phosphorescent dye other components of the film. Knowing the underlying interactions, unwanted processes can be suppressed. KW - OLED KW - Konjugierte Polymere KW - Mehrstoffsystem KW - OLED KW - conjugated polymers KW - multicomponent system Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-9484 ER - TY - JOUR A1 - Salert, Beatrice Ch. D. A1 - Krueger, Hartmut A1 - Bagnich, Sergey A. A1 - Unger, Thomas A1 - Jaiser, Frank A1 - Al-Sa'di, Mahmoud A1 - Neher, Dieter A1 - Hayer, Anna A1 - Eberle, Thomas T1 - New polymer matrix system for phosphorescent organic light-emitting diodes and the role of the small molecular co-host JF - Journal of polymer science : A, Polymer chemistry N2 - A new matrix system for phosphorescent organic light-emitting diodes (OLEDs) based on an electron transporting component attached to an inert polymer backbone, an electronically neutral co-host, and a phosphorescent dye that serves as both emitter and hole conductor are presented. The inert co-host is used either as small molecules or covalently connected to the same chain as the electron-transporting host. The use of a small molecular inert co-host in the active layer is shown to be highly advantageous in comparison to a purely polymeric matrix bearing the same functionalities. Analysis of the dye phosphorescence decay in pure polymer, small molecular co-host film, and their blend lets to conclude that dye molecules distribute mostly in the small molecular co-host phase, where the co-host prevents agglomeration and self-quenching of the phosphorescence as well as energy transfer to the electron transporting units. In addition, the co-host accumulates at the anode interface where it acts as electron blocking layer and improves hole injection. This favorable phase separation between polymeric and small molecular components results in devices with efficiencies of about 47 cd/A at a luminance of 1000 cd/m(2). Investigation of OLED degradation demonstrates the presence of two time regimes: one fast component that leads to a strong decrease at short times followed by a slower decrease at longer times. Unlike the long time degradation, the efficiency loss that occurs at short times is reversible and can be recovered by annealing of the device at 180 degrees C. We also show that the long-time degradation must be related to a change of the optical and electrical bulk properties. KW - charge transport KW - conducting polymer KW - degradation KW - host-guest systems KW - light-emitting diodes KW - random copolymer KW - synthesis KW - UV-vis spectroscopy Y1 - 2013 U6 - https://doi.org/10.1002/pola.26409 SN - 0887-624X VL - 51 IS - 3 SP - 601 EP - 613 PB - Wiley-Blackwell CY - Hoboken ER - TY - JOUR A1 - Luszczynska, Beata A1 - Dobruchowska, Ewa A1 - Glowacki, Ireneusz A1 - Ulanski, Jacek A1 - Jaiser, Frank A1 - Yang, Xiaohui A1 - Neher, Dieter A1 - Danel, Andrzej T1 - Poly(N-vinylcarbazole) doped with a pyrazoloquinoline dye : a deep blue light-emitting composite for light- emitting diode applications N2 - We investigated the spectral properties of light-emitting diodes based on a deep blue-emitting pyrazoloquinoline dye doped into a poly(N-vinylcarbazole)-based matrix. Even though the electroluminescence (EL) of the host is redshifted and broadened with respect to the emission of the dye, the EL spectrum becomes fully dominated by the dye emission at concentrations of ca. 2 wt %. This is attributed to a competition of exciplex formation on the matrix and exciton formation on the dye. Y1 - 2006 UR - http://jap.aip.org/ U6 - https://doi.org/10.1063/1.2162268 SN - 0021-8979 ER - TY - JOUR A1 - Kurpiers, Jona A1 - Ferron, Thomas A1 - Roland, Steffen A1 - Jakoby, Marius A1 - Thiede, Tobias A1 - Jaiser, Frank A1 - Albrecht, Steve A1 - Janietz, Silvia A1 - Collins, Brian A. A1 - Howard, Ian A. A1 - Neher, Dieter T1 - Probing the pathways of free charge generation in organic bulk heterojunction solar cells JF - Nature Communications N2 - The fact that organic solar cells perform efficiently despite the low dielectric constant of most photoactive blends initiated a long-standing debate regarding the dominant pathways of free charge formation. Here, we address this issue through the accurate measurement of the activation energy for free charge photogeneration over a wide range of photon energy, using the method of time-delayed collection field. For our prototypical low bandgap polymer:fullerene blends, we find that neither the temperature nor the field dependence of free charge generation depend on the excitation energy, ruling out an appreciable contribution to free charge generation though hot carrier pathways. On the other hand, activation energies are on the order of the room temperature thermal energy for all studied blends. We conclude that charge generation in such devices proceeds through thermalized charge transfer states, and that thermal energy is sufficient to separate most of these states into free charges. Y1 - 2018 U6 - https://doi.org/10.1038/s41467-018-04386-3 SN - 2041-1723 VL - 9 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Yang, Xiao Hui A1 - Jaiser, Frank A1 - Neher, Dieter A1 - Lawson, PaDreyia V. A1 - Brédas, Jean-Luc A1 - Zojer, Egbert A1 - Güntner, Roland A1 - Scanduicci de Freitas, Patricia A1 - Forster, Michael A1 - Scherf, Ullrich T1 - Suppression of the keto-emission in polyfluorene light-emitting diodes : Experiments and models N2 - The spectral characteristics of polyfluorene (PF)-based light-emitting diodes (LEDs) containing a defined low concentration of either keto-defects or of the polymer poly(9.9-octylfuorene-co-benzothiadiazole) (F8BT) are preseneted. Both types of blend layers were tested in different device configurations with respect to the relative and absolute intensities of green blue emission components. It is shown that blending hole-transporting molecules into the emission layer at low concentration or incorporation of a suitable hole-transport layer reduces the green emission contribution in the electroluminescence (EL) spectrum of the PF:F8BT blend, which is similar to what is observed for the keto- containing PF layer. We conclude that the keto-defects in PF homopolymer layers mainly constitute weakly emissive electron traps, in agreement with the results of quantum-mechanical calculations Y1 - 2004 SN - 1616-301X ER -