TY - GEN A1 - Taubert, Andreas A1 - Balischewski, Christian A1 - Hentrich, Doreen A1 - Elschner, Thomas A1 - Eidner, Sascha A1 - Günter, Christina A1 - Behrens, Karsten A1 - Heinze, Thomas T1 - Water-soluble cellulose derivatives are sustainable additives for biomimetic calcium phosphate mineralization N2 - The effect of cellulose-based polyelectrolytes on biomimetic calcium phosphate mineralization is described. Three cellulose derivatives, a polyanion, a polycation, and a polyzwitterion were used as additives. Scanning electron microscopy, X-ray diffraction, IR and Raman spectroscopy show that, depending on the composition of the starting solution, hydroxyapatite or brushite precipitates form. Infrared and Raman spectroscopy also show that significant amounts of nitrate ions are incorporated in the precipitates. Energy dispersive X-ray spectroscopy shows that the Ca/P ratio varies throughout the samples and resembles that of other bioinspired calcium phosphate hybrid materials. Elemental analysis shows that the carbon (i.e., polymer) contents reach 10% in some samples, clearly illustrating the formation of a true hybrid material. Overall, the data indicate that a higher polymer concentration in the reaction mixture favors the formation of polymer-enriched materials, while lower polymer concentrations or high precursor concentrations favor the formation of products that are closely related to the control samples precipitated in the absence of polymer. The results thus highlight the potential of (water-soluble) cellulose derivatives for the synthesis and design of bioinspired and bio-based hybrid materials. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 354 KW - cellulose KW - polyamine KW - polyammonium salt KW - polycarboxylate KW - polyzwitterion KW - calcium phosphate KW - biomineralization KW - brushite KW - hydroyxapatite KW - biomaterial Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-400453 ER - TY - BOOK A1 - Taubert, Andreas T1 - Ionische Flüssigkeiten : chemische Kuriosa oder sind sie doch recht nützlich? ; Antrittsvorlesung 2007-05-24 N2 - Klassischerweise haben Salze, beispielsweise Kochsalz, Schmelzpunkte von einigen hundert Grad Celsius und mehr. Ionische Flüssigkeiten sind dagegen Salze, deren Schmelzpunkt zum Teil weit unter der Raumtemperatur liegt. Sie sind daher bei Raumtemperatur flüssig. Obwohl ionische Flüssigkeiten seit 1914 bekannt sind, hatten sie bis vor 15 Jahren keinerlei Bedeutung. Heute jedoch werden ionische Flüssigkeiten aufgrund ihrer vorteilhaften Eigenschaften, wie hohe Leitfähigkeit oder hohe Temperaturstabilität, unter anderem zur Papierverarbeitung oder in flexiblen Solarzellen eingesetzt. Die Antrittsvorlesung wird sich insbesondere mit der Herstellung anorganischer Partikel befassen und zeigen, wie ionische Flüssigkeiten zur Herstellung neuer Materialien für verschiedene Anwendungen genutzt werden können. Y1 - 2007 UR - http://info.ub.uni-potsdam.de/multimedia/show_projekt.php?projekt_id=23 PB - Univ.-Bibl. CY - Potsdam ER - TY - JOUR A1 - Taubert, Andreas T1 - Electrospinning of Ionogels: Current Status and Future Perspectives JF - European journal of inorganic chemistry : a journal of ChemPubSoc Europe N2 - Ionogels (IGs), also termed ion gels, are functional hybrid materials based on an ionic liquid (IL) and a polymeric, hybrid, or inorganic matrix. IGs combine the properties of the matrix such as mechanical strength with IL properties like high ionic conductivity, high thermal stability, or catalytic activity. IGs are thus attractive for many applications, but the vast majority of IGs made and published so far are bulk materials or dense films. Applications like sensing or catalysis, however, would benefit from IGs with high surface areas or defined surface morphologies or architectures. In spite of this, only relatively few examples of high-surface-area IGs have been made so far; this has mostly been achieved by electrospinning, which has proven to be a promising strategy towards advanced IGs. The current review discusses first developments and outlines the future potential of electrospun ionogels, predominantly from a materials and inorganic chemistry perspective. KW - Ionic liquids KW - Ionogels KW - Hybrid materials KW - Electrospinning KW - Heterogeneous catalysis KW - Sensors KW - Energy KW - Health Y1 - 2015 U6 - https://doi.org/10.1002/ejic.201402490 SN - 1434-1948 SN - 1099-0682 IS - 7 SP - 1148 EP - 1159 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tao, Lumi A1 - Liu, Yuchuan A1 - Wu, Dan A1 - Wei, Qiao-Hua A1 - Taubert, Andreas A1 - Xie, Zailai T1 - Luminescent Ionogels with Excellent Transparency, High Mechanical Strength, and High Conductivity JF - Nanomaterials N2 - The paper describes a new kind of ionogel with both good mechanical strength and high conductivity synthesized by confining the ionic liquid (IL) 1-butyl-3-methylimidazolium bis(trifluoromethane sulfonyl)imide ([Bmim][NTf₂]) within an organic–inorganic hybrid host. The organic–inorganic host network was synthesized by the reaction of methyltrimethoxysilane (MTMS), tetraethoxysilane (TEOS), and methyl methacrylate (MMA) in the presence of a coupling agent, offering the good mechanical strength and rapid shape recovery of the final products. The silane coupling agent 3-methacryloxypropyltrimethoxysilane (KH-570) plays an important role in improving the mechanical strength of the inorganic–organic hybrid, because it covalently connected the organic component MMA and the inorganic component SiO₂. Both the thermal stability and mechanical strength of the ionogel significantly increased by the addition of IL. The immobilization of [Bmim][NTf₂] within the ionogel provided the final ionogel with an ionic conductivity as high as ca. 0.04 S cm⁻¹ at 50 °C. Moreover, the hybrid ionogel can be modified with organosilica-modified carbon dots within the network to yield a transparent and flexible ionogel with strong excitation-dependent emission between 400 and 800 nm. The approach is, therefore, a blueprint for the construction of next-generation multifunctional ionogels. KW - ionic liquid KW - ionogel KW - carbon dots KW - organic–inorganic hybrid KW - luminescence KW - mechanical strength Y1 - 2020 U6 - https://doi.org/10.3390/nano10122521 SN - 2079-4991 VL - 10 IS - 12 PB - MDPI CY - Basel ER - TY - GEN A1 - Tao, Lumi A1 - Liu, Yuchuan A1 - Wu, Dan A1 - Wei, Qiao-Hua A1 - Taubert, Andreas A1 - Xie, Zailai T1 - Luminescent Ionogels with Excellent Transparency, High Mechanical Strength, and High Conductivity T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The paper describes a new kind of ionogel with both good mechanical strength and high conductivity synthesized by confining the ionic liquid (IL) 1-butyl-3-methylimidazolium bis(trifluoromethane sulfonyl)imide ([Bmim][NTf₂]) within an organic–inorganic hybrid host. The organic–inorganic host network was synthesized by the reaction of methyltrimethoxysilane (MTMS), tetraethoxysilane (TEOS), and methyl methacrylate (MMA) in the presence of a coupling agent, offering the good mechanical strength and rapid shape recovery of the final products. The silane coupling agent 3-methacryloxypropyltrimethoxysilane (KH-570) plays an important role in improving the mechanical strength of the inorganic–organic hybrid, because it covalently connected the organic component MMA and the inorganic component SiO₂. Both the thermal stability and mechanical strength of the ionogel significantly increased by the addition of IL. The immobilization of [Bmim][NTf₂] within the ionogel provided the final ionogel with an ionic conductivity as high as ca. 0.04 S cm⁻¹ at 50 °C. Moreover, the hybrid ionogel can be modified with organosilica-modified carbon dots within the network to yield a transparent and flexible ionogel with strong excitation-dependent emission between 400 and 800 nm. The approach is, therefore, a blueprint for the construction of next-generation multifunctional ionogels. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1058 KW - ionic liquid KW - ionogel KW - carbon dots KW - organic–inorganic hybrid KW - luminescence KW - mechanical strength Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-487334 SN - 1866-8372 IS - 1058 ER - TY - JOUR A1 - Si, Satyabrata A1 - Taubert, Andreas A1 - Mantion, Alexandre A1 - Rogez, Guillaume A1 - Rabu, Pierre T1 - Peptide-intercalated layered metal hydroxides effect of peptide chain length and side chain functionality on structural, optical and magnetic properties JF - Chemical science N2 - New hybrid materials have been prepared by grafting synthetic peptides in the interlayer spacing of Cu(II) and Co(II) layered simple hydroxides (LSHs). The interlayer spacing of the hybrids depends on the peptide chain length; the dependence is specific for the copper and cobalt-based hybrids. This suggests a metal-or LSH-specific interaction of the peptides with the respective inorganic layers. When tyrosine is present in the peptide, its fluorescence is quenched after grafting the peptide to the LSH. Studies of the luminescence vs. pH indicate deprotonation of the tyrosine moieties to tyrosinate at high pH, accompanied by the onset of luminescence. The luminescence increases with increasing OH- concentration, suggesting an application of the hybrids as chemical sensors. Moreover, the peptides influence the magnetic properties of the hybrids. The copper-based hybrids behave antiferromagnetically and the cobalt-based hybrids are ferrimagnets. Y1 - 2012 U6 - https://doi.org/10.1039/c2sc01087a SN - 2041-6520 VL - 3 IS - 6 SP - 1945 EP - 1957 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Shkilnyy, Andriy A1 - Schöne, Stefanie A1 - Rumplasch, Claudia A1 - Uhlmann, Annett A1 - Hedderich, Annett A1 - Günter, Christina A1 - Taubert, Andreas T1 - Calcium phosphate mineralization with linear poly(ethylene imine) a time-resolved study JF - Colloid and polymer science : official journal of the Kolloid-Gesellschaft N2 - We have earlier shown that linear poly(ethylene imine) (LPEI) is an efficient growth modifier for calcium phosphate mineralization from aqueous solution (Shkilnyy et al., Langmuir, 2008, 24 (5), 2102). The current study addresses the growth process and the reason why LPEI is such an effective additive. To that end, the solution pH and the calcium and phosphate concentrations were monitored vs. reaction time using potentiometric, complexometric, and photometric methods. The phase transformations in the precipitates and particle morphogenesis were analyzed by X-ray diffraction and transmission electron microscopy, respectively. All measurements reveal steep decreases of the pH, calcium, and phosphate concentrations along with a rapid precipitation of brushite nanoparticles early on in the reaction. Brushite transforms into hydroxyapatite (HAP) within the first 2 h, which is much faster than what is reported, for example, for calcium phosphate precipitated with poly(acrylic acid). We propose that poly(ethylene imine) acts as a proton acceptor (weak buffer), which accelerates the transformation from brushite to HAP by taking up the protons that are released from the calcium phosphate precipitate during the phase transformation. KW - Calcium phosphate KW - Polyethylene imine KW - Mineralization KW - Kinetics Y1 - 2011 U6 - https://doi.org/10.1007/s00396-011-2403-2 SN - 0303-402X VL - 289 IS - 8 SP - 881 EP - 888 PB - Springer CY - New York ER - TY - JOUR A1 - Shkilnyy, Andriy A1 - Gräf, Ralph A1 - Hiebl, Bernhard A1 - Neffe, Axel T. A1 - Friedrich, Alwin A1 - Hartmann, Juergen A1 - Taubert, Andreas T1 - Unprecedented, low cytotoxicity of spongelike calcium phosphate/poly(ethylene imine) hydrogel composites N2 - Covalently crosslinked PEI hydrogels are efficient templates for calcium phosphate mineralization in SBF. In contrast to the PEI hydrogels, non-crosslinked PEI does not lead to calcium phosphate nucleation and growth in SBF. The precipitate is a mixture of brushite and hydroxyapatite. The PEI/calcium phosphate composite material exhibits a sponge like morphology and a chemical composition that is interesting for implants. Cytotoxicity tests using Dictyostelium discoideum amoebae show that both the non-mineralized and mineralized hydrogels have a very low cytotoxicity. This suggests that next generation PEI hydrogels, where also the degradation products are non-toxic, could be interesting for biomedical applications. Y1 - 2009 UR - http://www3.interscience.wiley.com/cgi-bin/jhome/77002860 U6 - https://doi.org/10.1002/mabi.200800266 SN - 1616-5187 ER - TY - JOUR A1 - Shkilnyy, Andriy A1 - Brandt, Jessica A1 - Mantion, Alexandre A1 - Paris, Oskar A1 - Schlaad, Helmut A1 - Taubert, Andreas T1 - Calcium phosphate with a channel-like morphology by polymer templating N2 - Calcium phosphate mineralization from aqueous solution in the presence of organic growth modifiers has been intensely studied in the recent past. This is mostly due to potential applications of the resulting composites in the biomaterials field. Polymers in particular are efficient growth modifiers. As a result, there has been a large amount of work on polymeric growth modifiers. Interestingly, however, relatively little work has been done on polycationic additives. The current paper shows that poly(ethylene oxide)b-poly(L-lysine) block copolymers lead to an interesting morphology of calcium phosphate precipitated at room temperature and subjected to a mild heat treatment at 85 degrees C. Electron microscopy, synchrotron X-ray diffraction, and porosity analysis show that a (somewhat) porous material with channel-like features forms. Closer inspection using transmission electron microscopy shows that the channels are probably not real channels. Much rather the morphology is the result of the aggregation of ca. 100-nm-sized rodlike primary particles, which changes upon drying to exhibit the observed channel-like features. Comparison experiments conducted in the absence of polymer and with poly(ethylene oxide)-b-poly(L-glutamate) show that these features only form in the presence of the polycationic poly(L-lysine) block, suggesting a distinct interaction of the polycation with either the crystal or the phosphate ions prior to mineralization. Y1 - 2009 UR - http://pubs.acs.org/journal/cmatex U6 - https://doi.org/10.1021/Cm803244z SN - 0897-4756 ER - TY - JOUR A1 - Schweizer, S. A1 - Schuster, T. A1 - Junginger, Matthias A1 - Siekmeyer, Gerd A1 - Taubert, Andreas T1 - Surface modification of ickel/Titanium Alloy and Titanium Surfaces via a Polyelectrolyte Multilayer/Calcium Phosphate Hybrid Coating N2 - The report shows that simple LbL deposition of positively charged chitosan and negatively charged heparin can be used to efficiently modify the native surface of both NiTi and Ti without any previous treatments. Moreover, mineralization of the polymer multilayers with calcium phosphate leads to surfaces with low contact angles around 70 and 20 degrees for NiTi and Ti, respectively. This suggests that a polymer multilayer/calcium phosphate hybrid coating could be useful for making NiTi or Ti implants that are at the same time antibacterial (via the chitosan), suppress blood clot formation (via the heparin), and favor fast endothelialization (via the improved surface hydrophilicity compared to the respective neat material). Y1 - 2010 UR - http://onlinelibrary.wiley.com/doi/10.1002/mame.200900347/pdf U6 - https://doi.org/10.1002/mame.200900347 SN - 1438-7492 ER - TY - GEN A1 - Schneider, Matthias A1 - Günter, Christina A1 - Taubert, Andreas T1 - Co-deposition of a hydrogel/calcium phosphate hybrid layer on 3D printed poly(lactic acid) scaffolds via dip coating BT - Towards automated biomaterials fabrication T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The article describes the surface modification of 3D printed poly(lactic acid) (PLA) scaffolds with calcium phosphate (CP)/gelatin and CP/chitosan hybrid coating layers. The presence of gelatin or chitosan significantly enhances CP co-deposition and adhesion of the mineral layer on the PLA scaffolds. The hydrogel/CP coating layers are fairly thick and the mineral is a mixture of brushite, octacalcium phosphate, and hydroxyapatite. Mineral formation is uniform throughout the printed architectures and all steps (printing, hydrogel deposition, and mineralization) are in principle amenable to automatization. Overall, the process reported here therefore has a high application potential for the controlled synthesis of biomimetic coatings on polymeric biomaterials. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1057 KW - 3D printing KW - dip-coating KW - poly(lactic acid) KW - PLA KW - calcium phosphate KW - gelatin KW - chitosan KW - hydrogel KW - calcium phosphate hybrid material KW - biomaterials Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-474427 SN - 1866-8372 IS - 1057 ER - TY - JOUR A1 - Schneider, Matthias A1 - Günter, Christina A1 - Taubert, Andreas T1 - Co-deposition of a hydrogel/calcium phosphate hybrid layer on 3D printed poly(lactic acid) scaffolds via dip coating BT - Towards Automated Biomaterials Fabrication JF - Polymers N2 - The article describes the surface modification of 3D printed poly(lactic acid) (PLA) scaffolds with calcium phosphate (CP)/gelatin and CP/chitosan hybrid coating layers. The presence of gelatin or chitosan significantly enhances CP co-deposition and adhesion of the mineral layer on the PLA scaffolds. The hydrogel/CP coating layers are fairly thick and the mineral is a mixture of brushite, octacalcium phosphate, and hydroxyapatite. Mineral formation is uniform throughout the printed architectures and all steps (printing, hydrogel deposition, and mineralization) are in principle amenable to automatization. Overall, the process reported here therefore has a high application potential for the controlled synthesis of biomimetic coatings on polymeric biomaterials. KW - 3D printing KW - dip-coating KW - poly(lactic acid) KW - PLA KW - calcium phosphate KW - gelatin KW - chitosan KW - hydrogel KW - calcium phosphate hybrid material KW - biomaterials Y1 - 2018 U6 - https://doi.org/10.3390/polym10030275 SN - 2073-4360 VL - 10 IS - 3 PB - MDPI CY - Basel ER - TY - JOUR A1 - Schneider, Matthias A1 - Fritzsche, Nora A1 - Puciul-Malinowska, Agnieszka A1 - Baliś, Andrzej A1 - Mostafa, Amr A1 - Bald, Ilko A1 - Zapotoczny, Szczepan A1 - Taubert, Andreas T1 - Surface etching of 3D printed poly(lactic acid) with NaOH BT - a systematic approach JF - Polymers N2 - The article describes a systematic investigation of the effects of an aqueous NaOH treatment of 3D printed poly(lactic acid) (PLA) scaffolds for surface activation. The PLA surface undergoes several morphology changes and after an initial surface roughening, the surface becomes smoother again before the material dissolves. Erosion rates and surface morphologies can be controlled by the treatment. At the same time, the bulk mechanical properties of the treated materials remain unaltered. This indicates that NaOH treatment of 3D printed PLA scaffolds is a simple, yet viable strategy for surface activation without compromising the mechanical stability of PLA scaffolds. KW - surface modification KW - sodium hydroxide etching KW - poly(lactic acid) KW - 3D KW - printing KW - roughness KW - wettability KW - erosion Y1 - 2020 U6 - https://doi.org/10.3390/polym12081711 SN - 2073-4360 VL - 12 IS - 8 PB - MDPI CY - Basel ER - TY - GEN A1 - Schneider, Matthias A1 - Fritzsche, Nora A1 - Puciul-Malinowska, Agnieszka A1 - Balis, Andrzej A1 - Mostafa, Amr A1 - Bald, Ilko A1 - Zapotoczny, Szczepan A1 - Taubert, Andreas T1 - Surface etching of 3D printed poly(lactic acid) with NaOH: a systematic approach T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The article describes a systematic investigation of the effects of an aqueous NaOH treatment of 3D printed poly(lactic acid) (PLA) scaffolds for surface activation. The PLA surface undergoes several morphology changes and after an initial surface roughening, the surface becomes smoother again before the material dissolves. Erosion rates and surface morphologies can be controlled by the treatment. At the same time, the bulk mechanical properties of the treated materials remain unaltered. This indicates that NaOH treatment of 3D printed PLA scaffolds is a simple, yet viable strategy for surface activation without compromising the mechanical stability of PLA scaffolds. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1212 KW - surface modification KW - sodium hydroxide etching KW - poly(lactic acid) KW - 3D printing KW - roughness KW - wettability KW - erosion Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-525088 SN - 1866-8372 IS - 8 ER - TY - JOUR A1 - Schneider, Matthias A1 - Fritzsche, Nora A1 - Puciul-Malinowska, Agnieszka A1 - Balis, Andrzej A1 - Mostafa, Amr A1 - Bald, Ilko A1 - Zapotoczny, Szczepan A1 - Taubert, Andreas T1 - Surface etching of 3D printed poly(lactic acid) with NaOH: a systematic approach JF - Polymers N2 - The article describes a systematic investigation of the effects of an aqueous NaOH treatment of 3D printed poly(lactic acid) (PLA) scaffolds for surface activation. The PLA surface undergoes several morphology changes and after an initial surface roughening, the surface becomes smoother again before the material dissolves. Erosion rates and surface morphologies can be controlled by the treatment. At the same time, the bulk mechanical properties of the treated materials remain unaltered. This indicates that NaOH treatment of 3D printed PLA scaffolds is a simple, yet viable strategy for surface activation without compromising the mechanical stability of PLA scaffolds. KW - surface modification KW - sodium hydroxide etching KW - poly(lactic acid) KW - 3D printing KW - roughness KW - wettability KW - erosion Y1 - 2020 VL - 12 IS - 8 PB - MDPI CY - Basel ER - TY - JOUR A1 - Salama, Ahmed A1 - Neumann, Mike A1 - Günter, Christina A1 - Taubert, Andreas T1 - Ionic liquid-assisted formation of cellulose/calcium phosphate hybrid materials JF - Beilstein journal of nanotechnology N2 - Cellulose/calcium phosphate hybrid materials were synthesized via an ionic liquid-assisted route. Scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, infrared spectroscopy, and thermogravimetric analysis/differential thermal analysis show that, depending on the reaction conditions, cellulose/hydroxyapatite, cellulose/ chlorapatite, or cellulose/monetite composites form. Preliminary studies with MC3T3-E1 pre-osteoblasts show that the cells proliferate on the hybrid materials suggesting that the ionic liquid-based process yields materials that are potentially useful as scaffolds for regenerative therapies. KW - biomineralization KW - calcium phosphate KW - carbohydrates KW - cellulose KW - hybrid materials KW - ionic liquid Y1 - 2014 U6 - https://doi.org/10.3762/bjnano.5.167 SN - 2190-4286 VL - 5 SP - 1553 EP - 1568 PB - Beilstein-Institut zur Förderung der Chemischen Wissenschaften CY - Frankfurt, Main ER - TY - JOUR A1 - Prieto, Susana A1 - Shkilnyy, Andriy A1 - Rumplasch, Claudia A1 - Ribeiro, Artur A1 - Javier Arias, F. A1 - Carlos Rodriguez-Cabello, Jose A1 - Taubert, Andreas T1 - Biomimetic calcium phosphate mineralization with multifunctional elastin-like recombinamers JF - Biomacromolecules : an interdisciplinary journal focused at the interface of polymer science and the biological sciences N2 - Biomimetic hybrid materials based on a polymeric and an inorganic component such as calcium phosphate are potentially useful for bone repair. The current study reports on a new approach toward biomimetic hybrid materials using a set of recombinamers (recombinant protein materials obtained from a synthetic gene) as crystallization additive for calcium phosphate. The recombinamers contain elements from elastin, an elastic structural protein, and statherin, a salivary protein. Via genetic engineering, the basic elastin sequence was modified with the SN(A)15 domain of statherin, whose interaction with calcium phosphate is well-established. These new materials retain the biocompatibility, "smart" nature, and desired mechanical behavior of the elastin-like recombinamer (ELR) family. Mineralization in simulated body fluid (SBF) in the presence of these recombinamers reveals surprising differences. Two of the polymers inhibit calcium phosphate deposition (although they contain the statherin segment). In contrast, the third polymer, which has a triblock structure, efficiently controls the calcium phosphate formation, yielding spherical hydroxyapatite (HAP) nanoparticles with diameters from 1 to 3 nm after 1 week in SBF at 37 degrees C. However, at lower temperatures, no precipitation is observed with any of the polymers. The data thus suggest that the molecular design of ELRs containing statherin segments and the selection of an appropriate polymer structure are key parameters to obtain functional materials for the development of intelligent systems for hard tissue engineering and subsequent in vivo applications. Y1 - 2011 U6 - https://doi.org/10.1021/bm200287c SN - 1525-7797 VL - 12 IS - 5 SP - 1480 EP - 1486 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Pereira, Rui F. P. A1 - Zehbe, Kerstin A1 - Günter, Christina A1 - dos Santos, Tiago A1 - Nunes, Silvia C. A1 - Almeida Paz, Filipe A. A1 - Silva, Maria M. A1 - Granja, Pedro L. A1 - Taubert, Andreas A1 - de Zea Bermudez, Verónica T1 - Ionic liquid-assisted synthesis of mesoporous silk fibroin/silica hybrids for biomedical applications JF - ACS Omega N2 - New mesoporous silk fibroin (SF)/silica hybrids were processed via a one-pot soft and energy-efficient sol-gel chemistry and self-assembly from a silica precursor, an acidic or basic catalyst, and the ionic liquid 1-butyl-3-methylimidazolium chloride, acting as both solvent and mesoporosity-inducer. The as-prepared materials were obtained as slightly transparent-opaque, amorphous monoliths, easily transformed into powders, and stable up to ca. 300 degrees C. Structural data suggest the formation of a hexagonal mesostructure with low range order and apparent surface areas, pore volumes, and pore radii of 205-263 m(2) g(-1), 0.16-0.19 cm(3) g(-1), and 1.2-1.6 nm, respectively. In all samples, the dominating conformation of the SF chains is the beta-sheet. Cytotoxicity/bioactivity resazurin assays and fluorescence microscopy demonstrate the high viability of MC3T3 pre-osteoblasts to indirect (>= 99 +/- 9%) and direct (78 +/- 2 to 99 +/- 13%) contact with the SF/silica materials. Considering their properties and further improvements, these systems are promising candidates to be explored in bone tissue engineering. They also offer excellent prospects as electrolytes for solid-state electrochemical devices, in particular for fuel cells. Y1 - 2018 U6 - https://doi.org/10.1021/acsomega.8b02051 SN - 2470-1343 VL - 3 IS - 9 SP - 10811 EP - 10822 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Peh, Eddie A1 - Liedel, Clemens A1 - Taubert, Andreas A1 - Tauer, Klaus T1 - Composition inversion to form calcium carbonate mixtures JF - CrystEngComm N2 - Composition inversion takes place in equimolar solid mixtures of sodium or ammonium carbonate and calcium chloride with respect to the combination of anions and cations leading to the corresponding chloride and calcite in complete conversion. The transformation takes place spontaneously under a variety of different situations, even in a powdery mixture resting under ambient conditions. Powder X-ray diffraction data and scanning electron microscopy micrographs are presented to describe the course of the reaction and to characterize the reaction products. The incomplete reaction in the interspace between two compressed tablets of pure starting materials leads to an electric potential due to the presence of uncompensated charges. Y1 - 2017 U6 - https://doi.org/10.1039/c7ce00433h SN - 1466-8033 VL - 19 SP - 3573 EP - 3583 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Pan, Xuefeng A1 - Sarhan, Radwan Mohamed A1 - Kochovski, Zdravko A1 - Chen, Guosong A1 - Taubert, Andreas A1 - Mei, Shilin A1 - Lu, Yan T1 - Template synthesis of dual-functional porous MoS2 nanoparticles with photothermal conversion and catalytic properties JF - Nanoscale N2 - Advanced catalysis triggered by photothermal conversion effects has aroused increasing interest due to its huge potential in environmental purification. In this work, we developed a novel approach to the fast degradation of 4-nitrophenol (4-Nip) using porous MoS2 nanoparticles as catalysts, which integrate the intrinsic catalytic property of MoS2 with its photothermal conversion capability. Using assembled polystyrene-b-poly(2-vinylpyridine) block copolymers as soft templates, various MoS 2 particles were prepared, which exhibited tailored morphologies (e.g., pomegranate-like, hollow, and open porous structures). The photothermal conversion performance of these featured particles was compared under near-infrared (NIR) light irradiation. Intriguingly, when these porous MoS2 particles were further employed as catalysts for the reduction of 4-Nip, the reaction rate constant was increased by a factor of 1.5 under NIR illumination. We attribute this catalytic enhancement to the open porous architecture and light-to-heat conversion performance of the MoS2 particles. This contribution offers new opportunities for efficient photothermal-assisted catalysis. Y1 - 2022 U6 - https://doi.org/10.1039/d2nr01040b SN - 2040-3372 VL - 14 IS - 18 SP - 6888 EP - 6901 PB - RSC Publ. (Royal Society of Chemistry) CY - Cambridge ER -