TY - THES A1 - Schulze, Nicole T1 - Neue Templatphasen zur anisotropen Goldnanopartikelherstellung durch den Einsatz strukturbildender Polymere T1 - New template phases for anisotropic gold nanoparticle production through the use of structure-forming polymers N2 - Ziel der vorliegenden Arbeit war die Synthese und Charakterisierung von anisotropen Goldnanopartikeln in einer geeigneten Polyelektrolyt-modifizierten Templatphase. Der Mittelpunkt bildet dabei die Auswahl einer geeigneten Templatphase, zur Synthese von einheitlichen und reproduzierbaren anisotropen Goldnanopartikeln mit den daraus resultierenden besonderen Eigenschaften. Bei der Synthese der anisotropen Goldnanopartikeln lag der Fokus in der Verwendung von Vesikeln als Templatphase, wobei hier der Einfluss unterschiedlicher strukturbildender Polymere (stark alternierende Maleamid-Copolymere PalH, PalPh, PalPhCarb und PalPhBisCarb mit verschiedener Konformation) und Tenside (SDS, AOT – anionische Tenside) bei verschiedenen Synthese- und Abtrennungsbedingungen untersucht werden sollte. Im ersten Teil der Arbeit konnte gezeigt werden, dass PalPhBisCarb bei einem pH-Wert von 9 die Bedingungen eines Röhrenbildners für eine morphologische Transformation von einer vesikulären Phase in eine röhrenförmige Netzwerkstruktur erfüllt und somit als Templatphase zur formgesteuerten Bildung von Nanopartikeln genutzt werden kann. Im zweiten Teil der Arbeit wurde dargelegt, dass die Templatphase PalPhBisCarb (pH-Wert von 9, Konzentration von 0,01 wt.%) mit AOT als Tensid und PL90G als Phospholipid (im Verhältnis 1:1) die effektivste Wahl einer Templatphase für die Bildung von anisotropen Strukturen in einem einstufigen Prozess darstellt. Bei einer konstanten Synthesetemperatur von 45 °C wurden die besten Ergebnisse bei einer Goldchloridkonzentration von 2 mM, einem Gold-Templat-Verhältnis von 3:1 und einer Synthesezeit von 30 Minuten erzielt. Ausbeute an anisotropen Strukturen lag bei 52 % (Anteil an dreieckigen Nanoplättchen von 19 %). Durch Erhöhung der Synthesetemperatur konnte die Ausbeute auf 56 % (29 %) erhöht werden. Im dritten Teil konnte durch zeitabhängige Untersuchungen gezeigt werden, dass bei Vorhandensein von PalPhBisCarb die Bildung der energetisch nicht bevorzugten Plättchen-Strukturen bei Raumtemperatur initiiert wird und bei 45 °C ein Optimum annimmt. Kintetische Untersuchungen haben gezeigt, dass die Bildung dreieckiger Nanoplättchen bei schrittweiser Zugabe der Goldchlorid-Präkursorlösung zur PalPhBisCarb enthaltenden Templatphase durch die Dosierrate der vesikulären Templatphase gesteuert werden kann. In umgekehrter Weise findet bei Zugabe der Templatphase zur Goldchlorid-Präkursorlösung bei 45 °C ein ähnlicher, kinetisch gesteuerter Prozess der Bildung von Nanodreiecken statt mit einer maximalen Ausbeute dreieckigen Nanoplättchen von 29 %. Im letzten Kapitel erfolgten erste Versuche zur Abtrennung dreieckiger Nanoplättchen von den übrigen Geometrien der gemischten Nanopartikellösung mittels tensidinduzierter Verarmungsfällung. Bei Verwendung von AOT mit einer Konzentration von 0,015 M wurde eine Ausbeute an Nanoplättchen von 99 %, wovon 72 % dreieckiger Geometrien hatten, erreicht. N2 - The aim of the present work was the synthesis and characterization of anisotropic gold nanoparticles in a suitable polyelectrolyte-modified template phase. The focus was on the selection of a suitable template phase for the synthesis of uniform and reproducible anisotropic gold nanoparticles with the resulting special properties. In the synthesis of the anisotropic gold nanoparticles, the focus was on the use of vesicles as a template phase. Here, the influence of different structure-forming polymers (strongly alternating maleimide copolymers PalH, PalPh, PalPhCarb and PalPhBisCarb with different conformations) and surfactants (SDS, AOT - anionic surfactants) should be studied at various synthesis and separation conditions. In the first part of the work, it could be shown that PalPhBisCarb at pH 9 meets the requirements of a tubulating agent for a morphological transformation of a vesicular phase into a tubular network structure and thus can be used as a template phase for the shape-controlled formation of nanoparticles. In the second part of the work, it was shown that the template phase PalPhBisCarb (pH value of 9, concentration of 0.01 wt.%) with AOT as surfactant and PL90G as phospholipid (in the ratio 1:1) is the most effective choice of template phase for the formation of anisotropic structures in a one-step process. At a constant synthesis temperature of 45 °C, the best results were achieved with a gold chloride concentration of 2 mM, a gold-template ratio of 3:1 and a synthesis time of 30 minutes. The yield of anisotropic structures was 52% (triangular nanoplatelet content of 19%). By increasing the synthesis temperature, the yield could be increased to 56% (29%). In the third part, it was shown by time-dependent investigations that in the presence of PalPhBisCarb, the formation of the not energetically preferred platelet structures is initiated at room temperature and assumes an optimum at 45 °C. Kinetical studies have shown that the formation of triangular nanosheets can be controlled by the dosing rate of the vesicular template phase when the gold chloride precursor solution is gradually added to the PalPhBisCarb-containing template phase. Conversely, upon addition of the template phase to the gold chloride precursor solution at 45 °C, a similar, kinetically controlled process of formation of nanodimers takes place with a maximum yield of triangular nanoplatelets of 29%. In the last chapter, initial attempts were made to separate triangular nanoplatelets from the other geometries of the mixed nanoparticle solution by means of surfactant-induced depletion flocculation. When AOT was used at a concentration of 0.015 M, a yield of nanoplatelets of 99%, of which 72% had triangular geometries, was achieved. KW - Nanopartikel KW - nanoparticle KW - Templatphase KW - template phase KW - Gold KW - gold KW - anisotrop KW - anisotropic Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-409515 ER - TY - THES A1 - Krüger, Stefanie T1 - Seidenbasierte anorganische Funktionsmaterialien T1 - Silk based inorganic functional materials N2 - In der vorliegenden Arbeit konnten erfolgreich zwei unterschiedliche Hybridmaterialien (HM) über die Sol-Gel-Methode synthetisiert werden. Bei den HM handelt es sich um Monolithe mit einem Durchmesser von bis zu 4,5 cm. Das erste HM besteht aus Titandioxid und Bombyx mori Seide und wird als TS bezeichnet, während das zweite weniger Seide und zusätzlich Polyethylenoxid (PEO) enthält und daher als TPS abgekürzt wird. Einige der HM wurden nach der Synthese in eine wässrige Tetrachloridogoldsäure-Lösung getaucht, wodurch sich auf der Oberfläche Goldnanopartikel gebildet haben. Die Materialien wurden mittels Elektronenmikroskopie, energiedispersiver Röntgenspektroskopie, Ramanspektroskopie sowie Röntgenpulverdiffraktometrie charakterisiert. Die Ergebnisse zeigen, dass beide HM aus etwa 5 nm großen, sphärischen Titandioxidnanopartikeln aufgebaut sind, die primär aus Anatas und zu einem geringen Anteil aus Brookit bestehen. Die Goldnanopartikel bei TPS_Au waren größer und polydisperser als die Goldnanopartikel auf dem TS_Au HM. Darüber hinaus sind die Goldnanopartikel im TS HM tiefer in das Material eingedrungen als beim TPS HM. Die weiterführende Analyse der HM mittels Elementaranalyse und thermogravimetrischer Analyse ergab für TPS einen geringeren Anteil an organischen Bestandteilen im HM als für TS, obwohl für beide Synthesen die gleiche Masse an organischen Materialien eingesetzt wurde. Es wird vermutet, dass das PEO während der Synthese teilweise wieder aus dem Material herausgewaschen wird. Diese Theorie korreliert mit den Ergebnissen aus der Stickstoffsorption und der Quecksilberporosimetrie, die für das TPS HM eine höhere Oberfläche als für das TS HM anzeigten. Die Variation einiger Syntheseparameter wie die Menge an Seide und PEO oder die Zusammensetzung der Titandioxidvorläuferlösung hatte einen großen Einfluss auf die synthetisierten HM. Während unterschiedliche Mengen an PEO die Größe des HM beeinflussten, konnte ohne Seide kein HM in einer ähnlichen Größe hergestellt werden. Die Bildung der HM wird stark von der Zusammensetzung der Titandioxidvorläuferlösung beeinflusst. Eine Veränderung führte daher nur selten zur Bildung eines homogenen HM. Die in dieser Arbeit synthetisierten HM wurden als Photokatalysatoren für die Wasserspaltung und den Abbau von Methylenblau eingesetzt. Bei der photokatalytischen Wasserspaltung wurde zunächst der Einfluss unterschiedlicher Goldkonzentrationen beim TPS HM auf die Wasserstoffausbeute untersucht. Die besten Ergebnisse wurden bei einer Menge von 2,5 mg Tetrachloridogoldsäure erhalten. Darüber hinaus wurde gezeigt, dass mit dem TPS HM eine deutlich höhere Menge an Wasserstoff gewonnen werden konnte als mit dem TS HM. Die Ursachen für die schlechtere Aktivität werden in der geringeren spezifischen Oberfläche, der unterschiedlichen Porenstruktur, dem höheren Anteil an Seide und besonders in der geringeren Größe und höheren Eindringtiefe der Goldnanopartikel vermutet. Darüber hinaus konnte mit einem höheren UV-Anteil in der Lichtquelle sowie durch die Zugabe von Ethanol als Opferreagenz eine Zunahme der Wasserstoffausbeute erzielt werden. Bei dem Methylenblauabbau wurde für beide HM zunächst nur eine Adsorption des Methylenblaus beobachtet. Nach der Zugabe von Wasserstoffperoxid konnte nach 8 h bereits eine fast vollständige Oxidation des Methylenblaus unter sichtbarem Licht beobachtet werden. Die Ursache für die etwas höhere Aktivität von TPS gegenüber TS wird in der unterschiedlichen Porenstruktur und dem höheren Anteil an Seide im TS HM vermutet. Insgesamt zeigen beide HM eine gute photokatalytische Aktivität für den Abbau von Methylenblau im Vergleich zu den erhaltenen Werten aus der Literatur. N2 - Two different hybrid materials (HM) were successfully synthesized by the sol-gel-method. The first HM is based on titania and Bombyx mori silk and will be denoted as TS. The second HM is TPS and also contains titania but a lower amount of silk and additionally poly(ethylene oxide) (PEO). Furthermore some of the HM were immerse in aqueous hydrogen tetrachloroaurate solutions to deposit gold nanoparticles (AuNP) on the surface of the HM. All materials are monoliths with diameters of up to ca. 4.5 cm. Analysis via electron microscopy, energy dispersive X-ray spectroscopy, Raman spectroscopy, and X-ray powder diffraction shows that the HM are based on 5 nm titania nanoparticles (TNP) – mainly anatase with a minor fraction of brookite - and AuNPs on the order of 7-18 nm. Addition of PEO to the reaction mixture enables pore size tuning which were analyzed by nitrogen sorption and mercury intrusion porosimetry measurements. These observations correlate with the results from elemental and thermogravimetric analysis which show a lower amount of organic components in TPS than in TS HM. In both HM the amount of organic components used for the synthesis are the same. Therefore we suppose that PEO is washed out of the material during the synthesis which yield to a higher surface area and a lower amount of organic components. A further chapter of the thesis describes the variation of different synthesis parameter like amount of silk or PEO or the composition of the titania precursor solution. The results show that it is impossible to create a HM of about 4.5 cm without silk. Furthermore the amount of PEO influences the size of the HM whereas the composition of the titania precursor solution has a large effect on the synthesis of such HM. Furthermore both HM were tested for their photocatalytic activities for water splitting and methylene blue (MB) degradation. Water splitting experiments using a sun simulator show that the new hybrid materials are effective water splitting catalysts and produce up to 30 mmol of hydrogen per 24 h. The amount of produced hydrogen is dependent on the HM (TPS_Au or TS_Au), the amount of AuNP, the addition of ethanol as sacrificial reagent or the light source. Studies of MB degradation show initially just an adsorption and not a degradation of MB. After the addition of hydrogen peroxide, there is an almost complete degradation of MB within 8 h. Both HM show a good photocatalytic activity for MB degradation compared with results from the literature. KW - photocatalytic water splitting KW - titania KW - Bombyx mori silk KW - gold KW - photokatalytische Wasserspaltung KW - Titandioxid KW - Gold KW - Bombyx mori Seide Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-404635 ER -