TY - JOUR A1 - Wang, Lei A1 - Rybacki, Erik A1 - Bonnelye, Audrey A1 - Bohnhoff, Marco A1 - Dresen, Georg T1 - Experimental investigation on static and dynamic bulk moduli of dry and fluid-saturated porous sandstones JF - Rock mechanics and rock engineering N2 - Knowledge of pressure-dependent static and dynamic moduli of porous reservoir rocks is of key importance for evaluating geological setting of a reservoir in geo-energy applications. We examined experimentally the evolution of static and dynamic bulk moduli for porous Bentheim sandstone with increasing confining pressure up to about 190 MPa under dry and water-saturated conditions. The static bulk moduli (K-s) were estimated from stress-volumetric strain curves while dynamic bulk moduli (K-d) were derived from the changes in ultrasonic P- and S- wave velocities (similar to 1 MHz) along different traces, which were monitored simultaneously during the entire deformation. In conjunction with published data of other porous sandstones (Berea, Navajo and Weber sandstones), our results reveal that the ratio between dynamic and static bulk moduli (K-d/K-s) reduces rapidly from about 1.5 - 2.0 at ambient pressure to about 1.1 at high pressure under dry conditions and from about 2.0 - 4.0 to about 1.5 under water-saturated conditions, respectively. We interpret such a pressure-dependent reduction by closure of narrow (compliant) cracks, highlighting thatK(d)/K(s)is positively correlated with the amount of narrow cracks. Above the crack closure pressure, where equant (stiff) pores dominate the void space,K-d/K(s)is almost constant. The enhanced difference between dynamic and static bulk moduli under water saturation compared to dry conditions is possibly caused by high pore pressure that is locally maintained if measured using high-frequency ultrasonic wave velocities. In our experiments, the pressure dependence of dynamic bulk modulus of water-saturated Bentheim sandstone at effective pressures above 5 MPa can be roughly predicted by both the effective medium theory (Mori-Tanaka scheme) and the squirt-flow model. Static bulk moduli are found to be more sensitive to narrow cracks than dynamic bulk moduli for porous sandstones under dry and water-saturated conditions. KW - Porous sandstone KW - Static bulk modulus KW - Dynamic bulk modulus KW - Narrow KW - (compliant) cracks KW - Equant (stiff) pores Y1 - 2020 U6 - https://doi.org/10.1007/s00603-020-02248-3 SN - 0723-2632 SN - 1434-453X VL - 54 IS - 1 SP - 129 EP - 148 PB - Springer CY - Wien ER - TY - JOUR A1 - Wang, Lei A1 - Kwiatek, Grzegorz A1 - Rybacki, Erik A1 - Bohnhoff, Marco A1 - Dresen, Georg T1 - Injection-induced seismic moment release and laboratory fault slip BT - implications for fluid-induced seismicity JF - Geophysical research letters N2 - Understanding the relation between injection-induced seismic moment release and operational parameters is crucial for early identification of possible seismic hazards associated with fluid-injection projects. We conducted laboratory fluid-injection experiments on permeable sandstone samples containing a critically stressed fault at different fluid pressurization rates. The observed fluid-induced fault deformation is dominantly aseismic. Fluid-induced stick-slip and fault creep reveal that total seismic moment release of acoustic emission (AE) events is related to total injected volume, independent of respective fault slip behavior. Seismic moment release rate of AE scales with measured fault slip velocity. For injection-induced fault slip in a homogeneous pressurized region, released moment shows a linear scaling with injected volume for stable slip (steady slip and fault creep), while we find a cubic relation for dynamic slip. Our results highlight that monitoring evolution of seismic moment release with injected volume in some cases may assist in discriminating between stable slip and unstable runaway ruptures. KW - induced seismicity KW - seismic moment release KW - fluid injection KW - stick slip KW - fault creep KW - acoustic emission Y1 - 2020 U6 - https://doi.org/10.1029/2020GL089576 SN - 0094-8276 SN - 1944-8007 VL - 47 IS - 22 PB - American Geophysical Union CY - Washington ER - TY - JOUR A1 - Wang, Lei A1 - Kwiatek, Grzegorz A1 - Rybacki, Erik A1 - Bonnelye, Audrey A1 - Bohnhoff, Marco A1 - Dresen, Georg T1 - Laboratory study on fluid-induced fault slip behavior: the role of fluid pressurization rate JF - Geophysical research letters : GRL N2 - Understanding the physical mechanisms governing fluid-induced fault slip is important for improved mitigation of seismic risks associated with large-scale fluid injection. We conducted fluid-induced fault slip experiments in the laboratory on critically stressed saw-cut sandstone samples with high permeability using different fluid pressurization rates. Our experimental results demonstrate that fault slip behavior is governed by fluid pressurization rate rather than injection pressure. Slow stick-slip episodes (peak slip velocity < 4 mu m/s) are induced by fast fluid injection rate, whereas fault creep with slip velocity < 0.4 mu m/s mainly occurs in response to slow fluid injection rate. Fluid-induced fault slip may remain mechanically stable for loading stiffness larger than fault stiffness. Independent of fault slip mode, we observed dynamic frictional weakening of the artificial fault at elevated pore pressure. Our observations highlight that varying fluid injection rates may assist in reducing potential seismic hazards of field-scale fluid injection projects.
Plain Language Summary Human-induced earthquakes from field-scale fluid injection projects including enhanced geothermal system and deep wastewater injection have been documented worldwide. Although it is clear that fluid pressure plays a crucial role in triggering fault slip, the physical mechanism behind induced seismicity still remains poorly understood. We performed laboratory tests, and here we present two fluid-induced slip experiments conducted on permeable Bentheim sandstone samples crosscut by a fault that is critically stressed. Fault slip is then triggered by pumping the water from the bottom end of the sample at different fluid injection rates. Our results show that fault slip is controlled by fluid pressure increase rate rather than by the absolute magnitude of fluid pressure. In contrast to episodes of relatively rapid but stable sliding events caused by a fast fluid injection rate, fault creep is observed during slow fluid injection. Strong weakening of the dynamic friction coefficient of the experimental fault is observed at elevated pore pressure, independent of fault slip mode. These results may provide a better understanding of the complex behavior of fluid-induced fault slip on the field scale. KW - fault slip KW - fluid injection KW - induced seismicity KW - fluid pressurization KW - rate KW - stick-slip KW - fault creep Y1 - 2020 U6 - https://doi.org/10.1029/2019GL086627 SN - 0094-8276 SN - 1944-8007 VL - 47 IS - 6 PB - Wiley CY - Hoboken, NJ ER - TY - JOUR A1 - Wang, Lei A1 - Dresen, Georg A1 - Rybacki, Erik A1 - Bonnelye, Audrey A1 - Bohnhoff, Marco T1 - Pressure-dependent bulk compressibility of a porous granular material modeled by improved contact mechanics and micromechanical approaches BT - effects of surface roughness of grains JF - Acta materialia N2 - The change of the mechanical properties of granular materials with pressure is an important topic associated with many industrial applications. In this paper we investigate the influence of hydrostatic pressure (P-e) on the effective bulk compressibility (C-eff) of a granular material by applying two modified theoretical approaches that are based on contact mechanics and micromechanics, respectively. For a granular material composed of rough grains, an extended contact model is developed to elucidate the effect of roughness of grain surfaces on bulk compressibility. At relatively low pressures, the model predicts that the decrease of bulk compressibility with pressure may be described by a power law with an exponent of -1/2 (i.e., C-eff proportional to P-e(1/2) ), but deviates at intermediate pressures. At elevated pressures beyond full contact, bulk compressibility remains almost unchanged, which may be roughly evaluated by continuum contact mechanics. As an alternative explanation of pressure-dependent bulk compressibility, we suggest a micromechanical model that accounts for effects of different types of pore space present in granular materials. Narrow and compliant inter-granular cracks are approximated by three-dimensional oblate spheroidal cracks with rough surfaces, whereas the equant and stiff pores surrounded by three and four neighboring grains are modeled as tubular pores with cross sections of three and four cusp-like corners, respectively. In this model, bulk compressibility is strongly reduced with increasing pressure by progressive closure of rough-walled cracks. At pressures exceeding crack closure pressure, deformation of the remaining equant pores is largely insensitive to pressure, with almost no further change in bulk compressibility. To validate these models, we performed hydrostatic compression tests on Bentheim sandstone (a granular rock consisting of quartz with high porosity) under a wide range of pressure. The relation between observed microstructures and measured pressure-dependent bulk compressibility is well explained by both suggested models. KW - Bulk compressibility KW - Granular materials KW - Roughness KW - Micromechanical model KW - Contact model Y1 - 2020 U6 - https://doi.org/10.1016/j.actamat.2020.01.063 SN - 1359-6454 SN - 1873-2453 VL - 188 SP - 259 EP - 272 PB - Elsevier CY - Amsterdam ER -