TY - JOUR A1 - Zu, Fengshuo A1 - Wolff, Christian Michael A1 - Ralaiarisoa, Maryline A1 - Amsalem, Patrick A1 - Neher, Dieter A1 - Koch, Norbert T1 - Unraveling the Electronic Properties of Lead Halide Perovskites with Surface Photovoltage in Photoemission Studies JF - ACS applied materials & interfaces N2 - The tremendous success of metal-halide perovskites, especially in the field of photovoltaics, has triggered a substantial number of studies in understanding their optoelectronic properties. However, consensus regarding the electronic properties of these perovskites is lacking due to a huge scatter in the reported key parameters, such as work function (Φ) and valence band maximum (VBM) values. Here, we demonstrate that the surface photovoltage (SPV) is a key phenomenon occurring at the perovskite surfaces that feature a non-negligible density of surface states, which is more the rule than an exception for most materials under study. With ultraviolet photoelectron spectroscopy (UPS) and Kelvin probe, we evidence that even minute UV photon fluxes (500 times lower than that used in typical UPS experiments) are sufficient to induce SPV and shift the perovskite Φ and VBM by several 100 meV compared to dark. By combining UV and visible light, we establish flat band conditions (i.e., compensate the surface-state-induced surface band bending) at the surface of four important perovskites, and find that all are p-type in the bulk, despite a pronounced n-type surface character in the dark. The present findings highlight that SPV effects must be considered in all surface studies to fully understand perovskites’ photophysical properties. KW - lead halide perovskite films KW - ultraviolet photoelectron spectroscopy KW - Kelvin probe KW - surface band bending KW - surface photovoltage KW - surface states Y1 - 2019 U6 - https://doi.org/10.1021/acsami.9b05293 SN - 1944-8244 SN - 1944-8252 VL - 11 IS - 24 SP - 21578 EP - 21583 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Schürmann, H. A1 - Koch, Norbert A1 - Imperia, Paolo A1 - Schrader, Sigurd A1 - Jandke, M. A1 - Strohriegl, P. A1 - Schulz, Burkhard A1 - Leising, G. A1 - Brehmer, Ludwig T1 - Ultraviolet photoelectron spectroscopic study of heterocyclic model compounds for electroluminescent devices Y1 - 1999 ER - TY - JOUR A1 - Schubert, Marcel A1 - Frisch, Johannes A1 - Allard, Sybille A1 - Preis, Eduard A1 - Scherf, Ullrich A1 - Koch, Norbert A1 - Neher, Dieter T1 - Tuning side chain and main chain order in a prototypical donor-acceptor copolymer BT - implications for optical, electronic, and photovoltaic characteristics JF - Elementary Processes in Organic Photovoltaics N2 - The recent development of donor–acceptor copolymers has led to an enormous improvement in the performance of organic solar cells and organic field-effect transistors. Here we describe the synthesis, detailed characterisation, and application of a series of structurally modified copolymers to investigate fundamental structure–property relationships in this class of conjugated polymers. The interplay between chemical structure and optoelectronic properties is investigated. These are further correlated to the charge transport and solar cell performance, which allows us to link their chemical structure to the observed physical properties. KW - Aggregate states KW - All-polymer heterojunctions KW - Alternating copolymers KW - Ambipolar charge transport KW - Ambipolar materials KW - Backbone modifications KW - Bilayer solar cells KW - Charge separation KW - Conformational disorder KW - Crystalline phases KW - Donor-acceptor copolymers KW - Electron traps KW - Energetic disorder KW - Energy-level alignment KW - Fermi-level alignment KW - Fermi-level pinning KW - Interface dipole KW - Interlayer KW - Intrachain order KW - Intragap states KW - Microscopic morphology KW - Mobility imbalance KW - Mobility relaxation KW - Monte Carlo simulation KW - Multiple trapping model KW - Nonradiative recombination KW - OFET KW - Open-circuit voltage KW - Optoelectronic properties KW - Partially alternating copolymers KW - Photo-CELIV KW - Photocurrent KW - Photovoltaic gap KW - Polymer intermixing KW - Recombination losses KW - Spectral diffusion KW - Statistical copolymers KW - Stille-type cross-coupling KW - Structure-property relationships KW - Time-dependent mobility KW - Time-of-flight (TOF) KW - Transient photocurrent KW - Ultraviolet photoelectron spectroscopy KW - Vacuum-level alignment KW - X-ray photoelectron spectroscopy Y1 - 2016 SN - 978-3-319-28338-8 SN - 978-3-319-28336-4 U6 - https://doi.org/10.1007/978-3-319-28338-8_10 SN - 0065-3195 VL - 272 SP - 243 EP - 265 PB - Springer CY - Berlin ER - TY - JOUR A1 - Mansour, Ahmed E. A1 - Lungwitz, Dominique A1 - Schultz, Thorsten A1 - Arvind, Malavika A1 - Valencia, Ana M. A1 - Cocchi, Caterina A1 - Opitz, Andreas A1 - Neher, Dieter A1 - Koch, Norbert T1 - The optical signatures of molecular-doping induced polarons in poly(3-hexylthiophene-2,5-diyl) BT - individual polymer chains versus aggregates JF - Journal of materials chemistry : C, Materials for optical and electronic devices N2 - Optical absorption spectroscopy is a key method to investigate doped conjugated polymers and to characterize the doping-induced charge carriers, i.e., polarons. For prototypical poly(3-hexylthiophene-2,5-diyl) (P3HT), the absorption intensity of molecular dopant induced polarons is widely used to estimate the carrier density and the doping efficiency, i.e., the number of polarons formed per dopant molecule. However, the dependence of the polaron-related absorption features on the structure of doped P3HT, being either aggregates or separated individual chains, is not comprehensively understood in contrast to the optical absorption features of neutral P3HT. In this work, we unambiguously differentiate the optical signatures of polarons on individual P3HT chains and aggregates in solution, notably the latter exhibiting the same shape as aggregates in solid thin films. This is enabled by employing tris(pentafluorophenyl)borane (BCF) as dopant, as this dopant forms only ion pairs with P3HT and no charge transfer complexes, and BCF and its anion have no absorption in the spectral region of P3HT polarons. Polarons on individual chains exhibit absorption peaks at 1.5 eV and 0.6 eV, whereas in aggregates the high-energy peak is split into a doublet 1.3 eV and 1.65 eV, and the low-energy peak is shifted below 0.5 eV. The dependence of the fraction of solvated individual chains versus aggregates on absolute solution concentration, dopant concentration, and temperature is elucidated, and we find that aggregates predominate in solution under commonly used processing conditions. Aggregates in BCF-doped P3HT solution can be effectively removed upon simple filtering. From varying the filter pore size (down to 200 nm) and thin film morphology characterization with scanning force microscopy we reveal the aggregates' size dependence on solution absolute concentration and dopant concentration. Furthermore, X-ray photoelectron spectroscopy shows that the dopant loading in aggregates is higher than for individual P3HT chains. The results of this study help understanding the impact of solution pre-aggregation on thin film properties of molecularly doped P3HT, and highlight the importance of considering such aggregation for other doped conjugated polymers in general. Y1 - 2020 U6 - https://doi.org/10.1039/c9tc06509a SN - 2050-7526 SN - 2050-7534 VL - 8 IS - 8 SP - 2870 EP - 2879 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Caprioglio, Pietro A1 - Wolff, Christian Michael A1 - Marquez, Jose A. A1 - Nordmann, Joleik A1 - Zhang, Shanshan A1 - Rothhardt, Daniel A1 - Hörmann, Ulrich A1 - Amir, Yohai A1 - Redinger, Alex A1 - Kegelmann, Lukas A1 - Zu, Fengshuo A1 - Albrecht, Steve A1 - Koch, Norbert A1 - Kirchartz, Thomas A1 - Saliba, Michael A1 - Unold, Thomas A1 - Neher, Dieter T1 - The impact of energy alignment and interfacial recombination on the internal and external open-circuit voltage of perovskite solar cells JF - Energy & environmental science N2 - Charge transport layers (CTLs) are key components of diffusion controlled perovskite solar cells, however, they can induce additional non-radiative recombination pathways which limit the open circuit voltage (V-OC) of the cell. In order to realize the full thermodynamic potential of the perovskite absorber, both the electron and hole transport layer (ETL/HTL) need to be as selective as possible. By measuring the photoluminescence yield of perovskite/CTL heterojunctions, we quantify the non-radiative interfacial recombination currents in pin- and nip-type cells including high efficiency devices (21.4%). Our study comprises a wide range of commonly used CTLs, including various hole-transporting polymers, spiro-OMeTAD, metal oxides and fullerenes. We find that all studied CTLs limit the V-OC by inducing an additional non-radiative recombination current that is in most cases substantially larger than the loss in the neat perovskite and that the least-selective interface sets the upper limit for the V-OC of the device. Importantly, the V-OC equals the internal quasi-Fermi level splitting (QFLS) in the absorber layer only in high efficiency cells, while in poor performing devices, the V-OC is substantially lower than the QFLS. Using ultraviolet photoelectron spectroscopy and differential charging capacitance experiments we show that this is due to an energy level mis-alignment at the p-interface. The findings are corroborated by rigorous device simulations which outline important considerations to maximize the V-OC. This work highlights that the challenge to suppress non-radiative recombination losses in perovskite cells on their way to the radiative limit lies in proper energy level alignment and in suppression of defect recombination at the interfaces. Y1 - 2019 U6 - https://doi.org/10.1039/c9ee02020a SN - 1754-5692 SN - 1754-5706 VL - 12 IS - 9 SP - 2778 EP - 2788 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Castellani, Mauro A1 - Salzmann, Ingo A1 - Bugnon, Philippe A1 - Yu, Shuwen A1 - Oehzelt, Martin A1 - Koch, Norbert T1 - Structural and electronic implications for carrier injection into organic semiconductors N2 - We report on the structural and electronic interface formation between ITO (indium-tin-oxide) and prototypical organic small molecular semiconductors, i.e., CuPc (copper phthalocyanine) and alpha-NPD (N,N'-di(naphtalen-1-yl)- N,N'-diphenyl-benzidine). In particular, the effects of in situ oxygen plasma pretreatment of the ITO surface on interface properties are examined in detail: Organic layer-thickness dependent Kelvin probe measurements revealed a good alignment of the ITO work function and the highest occupied electronic level of the organic material in all samples. In contrast, the electrical properties of hole-only and bipolar organic diodes depend strongly on the treatment of ITO prior to organic deposition. This dependence is more pronounced for diodes made of polycrystalline CuPc than for those of amorphous alpha-NPD layers. X-ray diffraction and atomic force microscopic (AFM) investigations of CuPc nucleation and growth evidenced a more pronounced texture of the polycrystalline film structure on the ITO substrate that was oxygen plasma treated prior to organic layer deposition. These findings suggest that the anisotropic electrical properties of CuPc crystallites, and their orientation with respect to the substrate, strongly affect the charge carrier injection and transport properties at the anode interface. Y1 - 2009 UR - http://www.springerlink.com/content/100501 U6 - https://doi.org/10.1007/s00339-009-5336-6 SN - 0947-8396 ER - TY - JOUR A1 - Hörmann, Ulrich A1 - Zeiske, Stefan A1 - Piersimoni, Fortunato A1 - Hoffmann, Lukas A1 - Schlesinger, Raphael A1 - Koch, Norbert A1 - Riedl, Thomas A1 - Andrienko, Denis A1 - Neher, Dieter T1 - Stark effect of hybrid charge transfer states at planar ZnO/organic interfaces JF - Physical review : B, Condensed matter and materials physics N2 - We investigate the bias dependence of the hybrid charge transfer state emission at planar heterojunctions between the metal oxide acceptor ZnO and three donor molecules. The electroluminescence peak energy linearly increases with the applied bias, saturating at high fields. Variation of the organic layer thickness and deliberate change of the ZnO conductivity through controlled photodoping allow us to confirm that this bias-induced spectral shift relates to the internal electric field in the organic layer rather than the filling of states at the hybrid interface. We show that existing continuum models overestimate the hole delocalization and propose a simple electrostatic model in which the linear and quadratic Stark effects are explained by the electrostatic interaction of a strongly polarizable molecular cation with its mirror image. Y1 - 2018 U6 - https://doi.org/10.1103/PhysRevB.98.155312 SN - 2469-9950 SN - 2469-9969 VL - 98 IS - 15 PB - American Physical Society CY - College Park ER - TY - JOUR A1 - Neusser, David A1 - Sun, Bowen A1 - Tan, Wen Liang A1 - Thomsen, Lars A1 - Schultz, Thorsten A1 - Perdigon-Toro, Lorena A1 - Koch, Norbert A1 - Shoaee, Safa A1 - McNeill, Christopher R. A1 - Neher, Dieter A1 - Ludwigs, Sabine T1 - Spectroelectrochemically determined energy levels of PM6:Y6 blends and their relevance to solar cell performance JF - Journal of materials chemistry : C, Materials for optical and electronic devices N2 - Recent advances in organic solar cell performance have been mainly driven forward by combining high-performance p-type donor-acceptor copolymers (e.g.PM6) and non-fullerene small molecule acceptors (e.g.Y6) as bulk-heterojunction layers. A general observation in such devices is that the device performance, e.g., the open-circuit voltage, is strongly dependent on the processing solvent. While the morphology is a typically named key parameter, the energetics of donor-acceptor blends are equally important, but less straightforward to access in the active multicomponent layer. Here, we propose to use spectral onsets during electrochemical cycling in a systematic spectroelectrochemical study of blend films to access the redox behavior and the frontier orbital energy levels of the individual compounds. Our study reveals that the highest occupied molecular orbital offset (Delta E-HOMO) in PM6:Y6 blends is similar to 0.3 eV, which is comparable to the binding energy of Y6 excitons and therefore implies a nearly zero driving force for the dissociation of Y6 excitons. Switching the PM6 orientation in the blend films from face-on to edge-on in bulk has only a minor influence on the positions of the energy levels, but shows significant differences in the open circuit voltage of the device. We explain this phenomenon by the different interfacial molecular orientations, which are known to affect the non-radiative decay rate of the charge-transfer state. We compare our results to ultraviolet photoelectron spectroscopy data, which shows distinct differences in the HOMO offsets in the PM6:Y6 blend compared to neat films. This highlights the necessity to measure the energy levels of the individual compounds in device-relevant blend films. Y1 - 2022 U6 - https://doi.org/10.1039/d2tc01918c SN - 2050-7526 SN - 2050-7534 VL - 10 IS - 32 SP - 11565 EP - 11578 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Raoufi, Meysam A1 - Hörmann, Ulrich A1 - Ligorio, Giovanni A1 - Hildebrandt, Jana A1 - Pätzel, Michael A1 - Schultz, Thorsten A1 - Perdigón-Toro, Lorena A1 - Koch, Norbert A1 - List-Kratochvil, Emil A1 - Hecht, Stefan A1 - Neher, Dieter T1 - Simultaneous effect of ultraviolet radiation and surface modification on the work function and hole injection properties of ZnO thin films JF - Physica Status Solidi. A , Applications and materials science N2 - The combined effect of ultraviolet (UV) light soaking and self-assembled monolayer deposition on the work function (WF) of thin ZnO layers and on the efficiency of hole injection into the prototypical conjugated polymer poly(3-hexylthiophen-2,5-diyl) (P3HT) is systematically investigated. It is shown that the WF and injection efficiency depend strongly on the history of UV light exposure. Proper treatment of the ZnO layer enables ohmic hole injection into P3HT, demonstrating ZnO as a potential anode material for organic optoelectronic devices. The results also suggest that valid conclusions on the energy-level alignment at the ZnO/organic interfaces may only be drawn if the illumination history is precisely known and controlled. This is inherently problematic when comparing electronic data from ultraviolet photoelectron spectroscopy (UPS) measurements carried out under different or ill-defined illumination conditions. KW - charge injection across hybrid interfaces KW - energy-level alignments KW - hybrid metal oxides KW - organic interfaces Y1 - 2020 U6 - https://doi.org/10.1002/pssa.201900876 SN - 1862-6300 SN - 1862-6319 VL - 217 IS - 5 SP - 1 EP - 6 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Wolff, Christian Michael A1 - Zu, Fengshuo A1 - Paulke, Andreas A1 - Perdigón-Toro, Lorena A1 - Koch, Norbert A1 - Neher, Dieter T1 - Reduced Interface-Mediated Recombination for High Open-Circuit Voltages in CH3NH3PbI3 Solar Cells JF - Advanced materials N2 - Perovskite solar cells with all-organic transport layers exhibit efficiencies rivaling their counterparts that employ inorganic transport layers, while avoiding high-temperature processing. Herein, it is investigated how the choice of the fullerene derivative employed in the electron-transporting layer of inverted perovskite cells affects the open-circuit voltage (V-OC). It is shown that nonradiative recombination mediated by the electron-transporting layer is the limiting factor for the V-OC in the cells. By inserting an ultrathin layer of an insulating polymer between the active CH3NH3PbI3 perovskite and the fullerene, an external radiative efficiency of up to 0.3%, a V-OC as high as 1.16 V, and a power conversion efficiency of 19.4% are realized. The results show that the reduction of nonradiative recombination due to charge-blocking at the perovskite/organic interface is more important than proper level alignment in the search for ideal selective contacts toward high V-OC and efficiency. KW - electron-transport layers KW - nonradiative recombination KW - open-circuit voltage KW - perovskite solar cells Y1 - 2017 U6 - https://doi.org/10.1002/adma.201700159 SN - 0935-9648 SN - 1521-4095 VL - 29 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Zu, Fengshuo A1 - Schultz, Thorsten A1 - Wolff, Christian Michael A1 - Shin, Dongguen A1 - Frohloff, Lennart A1 - Neher, Dieter A1 - Amsalem, Patrick A1 - Koch, Norbert T1 - Position-locking of volatile reaction products by atmosphere and capping layers slows down photodecomposition of methylammonium lead triiodide perovskite JF - RSC Advances N2 - The remarkable progress of metal halide perovskites in photovoltaics has led to the power conversion efficiency approaching 26%. However, practical applications of perovskite-based solar cells are challenged by the stability issues, of which the most critical one is photo-induced degradation. Bare CH3NH3PbI3 perovskite films are known to decompose rapidly, with methylammonium and iodine as volatile species and residual solid PbI2 and metallic Pb, under vacuum under white light illumination, on the timescale of minutes. We find, in agreement with previous work, that the degradation is non-uniform and proceeds predominantly from the surface, and that illumination under N-2 and ambient air (relative humidity 20%) does not induce substantial degradation even after several hours. Yet, in all cases the release of iodine from the perovskite surface is directly identified by X-ray photoelectron spectroscopy. This goes in hand with a loss of organic cations and the formation of metallic Pb. When CH3NH3PbI3 films are covered with a few nm thick organic capping layer, either charge selective or non-selective, the rapid photodecomposition process under ultrahigh vacuum is reduced by more than one order of magnitude, and becomes similar in timescale to that under N-2 or air. We conclude that the light-induced decomposition reaction of CH3NH3PbI3, leading to volatile methylammonium and iodine, is largely reversible as long as these products are restrained from leaving the surface. This is readily achieved by ambient atmospheric pressure, as well as a thin organic capping layer even under ultrahigh vacuum. In addition to explaining the impact of gas pressure on the stability of this perovskite, our results indicate that covalently "locking" the position of perovskite components at the surface or an interface should enhance the overall photostability. Y1 - 2020 U6 - https://doi.org/10.1039/d0ra03572f SN - 2046-2069 VL - 10 IS - 30 SP - 17534 EP - 17542 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Zu, Fengshuo A1 - Warby, Jonathan A1 - Stolterfoht, Martin A1 - Li, Jinzhao A1 - Shin, Dongguen A1 - Unger, Eva A1 - Koch, Norbert T1 - Photoinduced energy-level realignment at interfaces between organic semiconductors and metal-halide perovskites JF - Physical review letters N2 - In contrast to the common conception that the interfacial energy-level alignment is affixed once the interface is formed, we demonstrate that heterojunctions between organic semiconductors and metal-halide perovskites exhibit huge energy-level realignment during photoexcitation. Importantly, the photoinduced level shifts occur in the organic component, including the first molecular layer in direct contact with the perovskite. This is caused by charge-carrier accumulation within the organic semiconductor under illumination and the weak electronic coupling between the junction components. Y1 - 2021 U6 - https://doi.org/10.1103/PhysRevLett.127.246401 SN - 0031-9007 SN - 1079-7114 VL - 127 IS - 24 PB - American Physical Society CY - College Park ER - TY - JOUR A1 - Schrader, Sigurd A1 - Imperia, Paolo A1 - Koch, Norbert A1 - Leising, G. A1 - Falk, B. T1 - Organic Light-emitting devices based on new heterocyclic compounds Y1 - 1999 ER - TY - JOUR A1 - Schrader, Sigurd A1 - Rieß, Walter A1 - Vestweber, H. A1 - Koch, Norbert T1 - New polymeric heterolayer systems for efficient light-emitting devices Y1 - 1998 ER - TY - JOUR A1 - Lu, Guanghao A1 - Blakesley, James C. A1 - Himmelberger, Scott A1 - Pingel, Patrick A1 - Frisch, Johannes A1 - Lieberwirth, Ingo A1 - Salzmann, Ingo A1 - Oehzelt, Martin A1 - Di Pietro, Riccardo A1 - Salleo, Alberto A1 - Koch, Norbert A1 - Neher, Dieter T1 - Moderate doping leads to high performance of semiconductor/insulator polymer blend transistors JF - Nature Communications N2 - Polymer transistors are being intensively developed for next-generation flexible electronics. Blends comprising a small amount of semiconducting polymer mixed into an insulating polymer matrix have simultaneously shown superior performance and environmental stability in organic field-effect transistors compared with the neat semiconductor. Here we show that such blends actually perform very poorly in the undoped state, and that mobility and on/off ratio are improved dramatically upon moderate doping. Structural investigations show that these blend layers feature nanometre-scale semiconductor domains and a vertical composition gradient. This particular morphology enables a quasi three-dimensional spatial distribution of semiconductor pathways within the insulating matrix, in which charge accumulation and depletion via a gate bias is substantially different from neat semiconductor, and where high on-current and low off-current are simultaneously realized in the stable doped state. Adding only 5 wt% of a semiconducting polymer to a polystyrene matrix, we realized an environmentally stable inverter with gain up to 60. Y1 - 2013 U6 - https://doi.org/10.1038/ncomms2587 SN - 2041-1723 VL - 4 IS - 1-2 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Zhao, Yuhang A1 - Opitz, Andreas A1 - Eljarrat, Alberto A1 - Kochovski, Zdravko A1 - Koch, Christoph A1 - Koch, Norbert A1 - Lu, Yan T1 - Kinetic study on the adsorption of 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane on Ag nanoparticles in chloroform BT - implications for the charge transfer complex of Ag-F(4)TCNQ JF - ACS applied nano materials N2 - In this study, the kinetics of the adsorption of 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F(4)TCNQ) on the surface of Ag nanoparticles (Ag NPs) in chloroform has been intensively investigated, as molecular doping is known to play a crucial role in organic electronic devices. Based on the results obtained from UV-visible (vis)-near-infrared (NIR) absorption spectroscopy, cryogenic transmission electron microscopy, scanning nanobeam electron diffraction, and electron energy loss spectroscopy, a two-step interaction kinetics has been proposed for the Ag NPs and F(4)TCNQ molecules, which includes the first step of electron transfer from Ag NPs to F(4)TCNQ indicated by the ionization of F(4)TCNQ and the second step of the formation of a Ag-F(4)TCNQ complex. The whole process has been followed via UV-vis-NIR absorption spectroscopy, which reveals distinct kinetics at two stages: the instantaneous ionization and the long-term complex formation. The kinetics and the influence of the molar ratio of Ag NPs/F(4)TCNQ molecules on the interaction between Ag NPs and F(4)TCNQ molecules in an organic solution are reported herein for the first time. Furthermore, the control experiment with silica-coated Ag NPs manifests that the charge transfer at the surface between Ag NPs and F(4)TCNQ molecules is prohibited by a silica layer of 18 nm. KW - Ag nanoparticles KW - F(4)TCNQ KW - phase transfer KW - kinetics KW - electron transfer KW - surface interaction Y1 - 2021 U6 - https://doi.org/10.1021/acsanm.1c02153 SN - 2574-0970 VL - 4 IS - 11 SP - 11625 EP - 11635 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Salzmann, Ingo A1 - Heimel, Georg A1 - Duhm, Steffen A1 - Oehzelt, Martin A1 - Pingel, Patrick A1 - George, Benjamin M. A1 - Schnegg, Alexander A1 - Lips, Klaus A1 - Blum, Ralf-Peter A1 - Vollmer, Antje A1 - Koch, Norbert T1 - Intermolecular hybridization governs molecular electrical doping JF - Physical review letters N2 - Current models for molecular electrical doping of organic semiconductors are found to be at odds with other well-established concepts in that field, like polaron formation. Addressing these inconsistencies for prototypical systems, we present experimental and theoretical evidence for intermolecular hybridization of organic semiconductor and dopant frontier molecular orbitals. Common doping-related observations are attributed to this phenomenon, and controlling the degree of hybridization emerges as a strategy for overcoming the present limitations in the yield of doping-induced charge carriers. Y1 - 2012 U6 - https://doi.org/10.1103/PhysRevLett.108.035502 SN - 0031-9007 VL - 108 IS - 3 PB - American Physical Society CY - College Park ER - TY - JOUR A1 - Zhang, Shanshan A1 - Stolterfoht, Martin A1 - Armin, Ardalan A1 - Lin, Qianqian A1 - Zu, Fengshuo A1 - Sobus, Jan A1 - Jin, Hui A1 - Koch, Norbert A1 - Meredith, Paul A1 - Burn, Paul L. A1 - Neher, Dieter T1 - Interface Engineering of Solution-Processed Hybrid Organohalide Perovskite Solar Cells JF - ACS applied materials & interfaces N2 - Engineering the interface between the perovskite absorber and the charge-transporting layers has become an important method for improving the charge extraction and open-circuit voltage (V-OC) of hybrid perovskite solar cells. Conjugated polymers are particularly suited to form the hole-transporting layer, but their hydrophobicity renders it difficult to solution-process the perovskite absorber on top. Herein, oxygen plasma treatment is introduced as a simple means to change the surface energy and work function of hydrophobic polymer interlayers for use as p-contacts in perovskite solar cells. We find that upon oxygen plasma treatment, the hydrophobic surfaces of different prototypical p-type polymers became sufficiently hydrophilic to enable subsequent perovskite junction processing. In addition, the oxygen plasma treatment also increased the ionization potential of the polymer such that it became closer to the valance band energy of the perovskite. It was also found that the oxygen plasma treatment could increase the electrical conductivity of the p-type polymers, facilitating more efficient charge extraction. On the basis of this concept, inverted MAPbI(3) perovskite devices with different oxygen plasma-treated polymers such as P3HT, P3OT, polyTPD, or PTAA were fabricated with power conversion efficiencies of up to 19%. KW - organohalide lead perovskites KW - solar cells KW - surface wetting KW - work function KW - oxygen plasma KW - transport layer Y1 - 2018 U6 - https://doi.org/10.1021/acsami.8b02503 SN - 1944-8244 VL - 10 IS - 25 SP - 21681 EP - 21687 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Schubert, Marcel A1 - Dolfen, Daniel A1 - Frisch, Johannes A1 - Roland, Steffen A1 - Steyrleuthner, Robert A1 - Stiller, Burkhard A1 - Chen, Zhihua A1 - Scherf, Ullrich A1 - Koch, Norbert A1 - Facchetti, Antonio A1 - Neher, Dieter T1 - Influence of aggregation on the performance of All-Polymer Solar Cells containing Low-Bandgap Naphthalenediimide Copolymers JF - dvanced energy materials N2 - The authors present efficient all-polymer solar cells comprising two different low-bandgap naphthalenediimide (NDI)-based copolymers as acceptors and regioregular P3HT as the donor. It is shown that these naphthalene copolymers have a strong tendency to preaggregate in specific organic solvents, and that preaggregation can be completely suppressed when using suitable solvents with large and highly polarizable aromatic cores. Organic solar cells prepared from such nonaggregated polymer solutions show dramatically increased power conversion efficiencies of up to 1.4%, which is mainly due to a large increase of the short circuit current. In addition, optimized solar cells show remarkable high fill factors of up to 70%. The analysis of the blend absorbance spectra reveals a surprising anticorrelation between the degree of polymer aggregation in the solid P3HT:NDI copolymer blends and their photovoltaic performance. Scanning near-field optical microscopy (SNOM) and atomic force microscopy (AFM) measurements reveal important information on the blend morphology. It is shown that films with high degree of aggregation and low photocurrents exhibit large-scale phase-separation into rather pure donor and acceptor domains. It is proposed that, by suppressing the aggregation of NDI copolymers at the early stage of film formation, the intermixing of the donor and acceptor component is improved, thereby allowing efficient harvesting of photogenerated excitons at the donoracceptor heterojunction. KW - aggregation KW - morphology KW - naphthalenediimide KW - organic semiconductors KW - organic photovoltaics Y1 - 2012 U6 - https://doi.org/10.1002/aenm.201100601 SN - 1614-6832 VL - 2 IS - 3 SP - 369 EP - 380 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Lu, Guanghao A1 - Koch, Norbert A1 - Neher, Dieter T1 - In-situ tuning threshold voltage of field-effect transistors based on blends of poly(3-hexylthiophene) with an insulator electret JF - Applied physics letters N2 - Blending the conjugated polymer poly(3-hexylthiophene) (P3HT) with the insulating electret polystyrene (PS), we show that the threshold voltage V-t of organic field-effect transistors (OFETs) can be easily and reversely tuned by applying a gate bias stress at 130 degrees C. It is proposed that this phenomenon is caused by thermally activated charge injection from P3HT into PS matrix, and that this charge is immobilized within the PS matrix after cooling down to room temperature. Therefore, room-temperature hysteresis-free FETs with desired V-t can be easily achieved. The approach is applied to reversely tune the OFET mode of operation from accumulation to depletion, and to build inverters. (C) 2015 AIP Publishing LLC. Y1 - 2015 U6 - https://doi.org/10.1063/1.4928554 SN - 0003-6951 SN - 1077-3118 VL - 107 IS - 6 PB - American Institute of Physics CY - Melville ER -