TY - JOUR A1 - Boggio, Jose M. Chavez A1 - Bodenmueller, D. A1 - Fremberg, T. A1 - Haynes, R. A1 - Roth, Martin M. A1 - Eisermann, R. A1 - Lisker, M. A1 - Zimmermann, L. A1 - Boehm, Michael T1 - Dispersion engineered silicon nitride waveguides by geometrical and refractive-index optimization JF - Journal of the Optical Society of America : B, Optical physics N2 - Dispersion engineering in silicon nitride (SiXNY) waveguides is investigated through the optimization of the waveguide transversal dimensions and refractive indices in a multicladding arrangement. Ultraflat dispersion of -84.0 +/- 0.5 ps/nm/km between 1700 and 2440 nm and 1.5 +/- 3 ps/nm/km between 1670 and 2500 nm is numerically demonstrated. It is shown that typical refractive index fluctuations as well as dimension fluctuations during fabrication of the SiXNY waveguides are a limitation for obtaining ultraflat dispersion profiles. Single- and multicladding waveguides are fabricated and their dispersion profiles measured (over nearly 1000 nm) using a low-coherence frequency domain interferometric technique. By appropriate thickness optimization, the zero-dispersion wavelength is tuned over a large spectral range in single-and multicladding waveguides with small refractive index contrast (3%). A flat dispersion profile with +/- 3.2 ps/nm/km variation over 500 nm is obtained in a multicladding waveguide fabricated with a refractive index contrast of 37%. Finally, we generate a nearly three-octave supercontinuum in this dispersion flattened multicladding SiXNY waveguide. (C) 2014 Optical Society of America Y1 - 2014 U6 - https://doi.org/10.1364/JOSAB.31.002846 SN - 0740-3224 SN - 1520-8540 VL - 31 IS - 11 SP - 2846 EP - 2857 PB - Optical Society of America CY - Washington ER - TY - GEN A1 - Schott, Juliane A1 - Kretzschmar, Jerome A1 - Acker, Margret A1 - Eidner, Sascha A1 - Kumke, Michael Uwe A1 - Drobot, Björn A1 - Barkleit, Astrid A1 - Taut, Steffen A1 - Brendler, Vinzenz A1 - Stumpf, Thorsten T1 - Formation of a Eu(III) borate solid species from a weak Eu(III) borate complex in aqueous solution N2 - In the presence of polyborates (detected by 11B-NMR) the formation of a weak Eu(III) borate complex (lg β11 ∼ 2, estimated) was observed by time-resolved laser-induced fluorescence spectroscopy (TRLFS). This complex is a precursor for the formation of a solid Eu(III) borate species. The formation of this solid in solution was investigated by TRLFS as a function of the total boron concentration: the lower the total boron concentration, the slower is the solid formation. The solid Eu(III) borate was characterized by IR spectroscopy, powder XRD and solid-state TRLFS. The determination of the europium to boron ratio portends the existence of pentaborate units in the amorphous solid. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 277 Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98774 ER - TY - GEN A1 - Plehn, Thomas A1 - Megow, Jörg A1 - May, Volkhard T1 - Concerted charge and energy transfer processes in a highly flexible fullerene–dye system BT - a mixed quantum–classical study N2 - Photoinduced excitation energy transfer and accompanying charge separation are elucidated for a supramolecular system of a single fullerene covalently linked to six pyropheophorbide-a dye molecules. Molecular dynamics simulations are performed to gain an atomistic picture of the architecture and the surrounding solvent. Excitation energy transfer among the dye molecules and electron transfer from the excited dyes to the fullerene are described by a mixed quantum–classical version of the Förster rate and the semiclassical Marcus rate, respectively. The mean characteristic time of energy redistribution lies in the range of 10 ps, while electron transfer proceeds within 150 ps. In between, on a 20 to 50 ps time-scale, conformational changes take place in the system. This temporal hierarchy of processes guarantees efficient charge separation, if the structure is exposed to a solvent. The fast energy transfer can adopt the dye excitation to the actual conformation. In this sense, the probability to achieve charge separation is large enough since any dominance of unfavorable conformations that exhibit a large dye–fullerene distance is circumvented. And the slow electron transfer may realize an averaging with respect to different conformations. To confirm the reliability of our computations, ensemble measurements on the charge separation dynamics are simulated and a very good agreement with the experimental data is obtained. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 279 Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98791 ER - TY - GEN A1 - Węcławski, Marek K. A1 - Tasior, Mariusz A1 - Hammann, Tommy A1 - Cywiński, Piotr J. A1 - Gryko, Daniel T. T1 - From π-expanded coumarins to π-expanded pentacenes N2 - The synthesis of two novel types of π-expanded coumarins has been developed. Modified Knoevenagel bis-condensation afforded 3,9-dioxa-perylene-2,8-diones. Subsequent oxidative aromatic coupling or light driven electrocyclization reaction led to dibenzo-1,7-dioxacoronene-2,8-dione. Unparalleled synthetic simplicity, straightforward purification and superb optical properties have the potential to bring these perylene and coronene analogs towards various applications. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 280 Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98822 ER - TY - GEN A1 - Cywiński, Piotr J. A1 - Nono, Katia Nchimi A1 - Charbonnière, Loïc J. A1 - Hammann, Tommy A1 - Löhmannsröben, Hans-Gerd T1 - Photophysical evaluation of a new functional terbium complex in FRET-based time-resolved homogenous fluoroassays N2 - A new functional luminescent lanthanide complex (LLC) has been synthesized with terbium as a central lanthanide ion and biotin as a functional moiety. Unlike in typical lanthanide complexes assembled via carboxylic moieties, in the presented complex, four phosphate groups are chelating the central lanthanide ion. This special chemical assembly enhances the complex stability in phosphate buffers conventionally used in biochemistry. The complex synthesis strategy and photophysical properties are described as well as the performance in time-resolved Förster Resonance Energy Transfer (FRET) assays. In those assays, this biotin-LLC transferred energy either to acceptor organic dyes (Cy5 or AF680) labelled on streptavidin or to quantum dots (QD655 or QD705) surface-functionalised with streptavidins. The permanent spatial donor–acceptor proximity is assured through strong and stable biotin–streptavidin binding. The energy transfer is evidenced from the quenching observed in donor emission and from a decrease in donor luminescence decay, both associated with simultaneous increase in acceptor intensity and in the decay time. The dye-based assays are realised in TRIS and in PBS, whereas QD-based systems are studied in borate buffer. The delayed emission analysis allows for quantifying the recognition process and for auto-fluorescence-free detection, which is particularly relevant for application in bioanalysis. In accordance with Förster theory, Förster-radii (R0) were found to be around 60 Å for organic dyes and around 105 Å for QDs. The FRET efficiency (η) reached 80% and 25% for dye and QD acceptors, respectively. Physical donor–acceptor distances (r) have been determined in the range 45–60 Å for organic dye acceptors, while for acceptor QDs between 120 Å and 145 Å. This newly synthesised biotin-LLC extends the class of highly sensitive analytical tools to be applied in the bioanalytical methods such as time-resolved fluoroimmunoassays (TR-FIA), luminescent imaging and biosensing. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 252 KW - acceptors KW - bioanalysis KW - contrast agents KW - europium KW - fluoroimmunoassay KW - labels KW - lanthanide luminescence KW - quantum dots KW - resonance energy-transfer Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-95390 SP - 6060 EP - 6067 ER - TY - THES A1 - Giordano, Cristina T1 - A neglected world: transition metal nitride and metal carbide based nanostructures T1 - Eine vernachlässigte Welt: Übergangsmetallnitrid- und Metallcarbid-basierte Nanostrukturen BT - novel synthesis and future perspectives BT - neuartige Synthese und Zukunftsperspektiven N2 - Potentiality of nanosized materials has been largely proved but a closer look shows that a significant percentage of this research is related to oxides and metals, while the number drastically drops for metallic ceramics, namely transition metal nitrides and metal carbides. The lack of related publications do not reflect their potential but rather the difficulties related to their synthesis as dense and defect-free structures, fundamental prerequisites for advanced mechanical applications. The present habilitation work aims to close the gap between preparation and processing, indicating novel synthetic pathways for a simpler and sustainable synthesis of transition metal nitride (MN) and carbide (MC) based nanostructures and easier processing thereafter. In spite of simplicity and reliability, the designed synthetic processes allow the production of functional materials, with the demanded size and morphology. The goal was achieved exploiting classical and less-classical precursors, ranging from common metal salts and molecules (e.g. urea, gelatin, agar, etc), to more exotic materials, such as leafs, filter paper and even wood. It was found that the choice of precursors and reaction conditions makes it possible to control chemical composition (going for instance from metal oxides to metal oxy-nitrides to metal nitrides, or from metal nitrides to metal carbides, up to quaternary systems), size (from 5 to 50 nm) and morphology (going from mere spherical nanoparticles to rod-like shapes, fibers, layers, meso-porous and hierarchical structures, etc). The nature of the mixed precursors also allows the preparation of metal nitrides/carbides based nanocomposites, thus leading to multifunctional materials (e.g. MN/MC@C, MN/MC@PILs, etc) but also allowing dispersion in liquid media. Control over composition, size and morphology is obtained with simple adjustment of the main route, but also coupling it with processes such as electrospin, aerosol spray, bio-templating, etc. Last but not least, the nature of the precursor materials also allows easy processing, including printing, coating, casting, film and thin layers preparation, etc). The designed routes are, concept-wise, similar and they all start by building up a secondary metal ion-N/C precursor network, which converts, upon heat treatment, into an intermediate “glass”. This glass stabilizes the nascent nanoparticles during their nucleation and impairs their uncontrolled growth during the heat treatment (scheme 1). This way, one of the main problems related to the synthesis of MN/MC, i.e. the need of very high temperature, could also be overcome (from up to 2000°C, for classical synthesis, down to 700°C in the present cases). The designed synthetic pathways are also conceived to allow usage of non-toxic compounds and to minimize (or even avoid) post-synthesis purification, still bringing to phase pure and well-defined (crystalline) nanoparticles. This research aids to simplify the preparation of MN/MC, making these systems now readily available in suitable amounts both for fundamental and applied science. The prepared systems have been tested (in some cases for the first time) in many different fields, e.g. battery (MnN0.43@C shown a capacity stabilized at a value of 230 mAh/g, with coulombic efficiencies close to 100%), as alternative magnetic materials (Fe3C nanoparticles were prepared with different size and therefore different magnetic behavior, superparamagnetic or ferromagnetic, showing a saturation magnetization value up to 130 emu/g, i.e. similar to the value expected for the bulk material), as filters and for the degradation of organic dyes (outmatching the performance of carbon), as catalysts (both as active phase but also as active support, leading to high turnover rate and, more interesting, to tunable selectivity). Furthermore, with this route, it was possible to prepare for the first time, to the best of our knowledge, well-defined and crystalline MnN0.43, Fe3C and Zn1.7GeN1.8O nanoparticles via bottom-up approaches. Once the synthesis of these materials can be made straightforward, any further modification, combination, manipulation, is in principle possible and new systems can be purposely conceived (e.g. hybrids, nanocomposites, ferrofluids, etc). N2 - Materialien sind wichtige Hilfsmittel, die wir täglich benutzen, um unser Leben einfacher zu machen. Materialien werden durch ihre Eigenschaften charakterisiert. Manche sind stark, manche sind elektrisch, manche magnetisch, usw. Wenn ein Stoff auf die Dimension eines Virus verkleinert wird, zeigen sich besondere Veränderungen. War das Material groß z.B. elektrisch, hat es klein diese Eigenschaft nicht mehr. Groß war es glanzlos, aber klein ist es transparent... Das heißt, dass jedes bekannte Material prinzipiell ein neues Material werden kann, nur durch die Veränderung seiner Größe. Wegen dieser besonderen Entdeckung, ist seit vielen Jahren ein Großteil der Forschung Nanopartikeln gewidmet. Dennoch werden in diesem Gebiet meistens besondere Materialien untersucht, weil ihre Anwendungsfelder weithin bekannt und wichtig sind. Meine Forschung basiert auf der Untersuchung neuer oder weniger bekannter Materialien, nämlich Übergangsmetallnitride und Übergangsmetallcarbide als Nanostrukturen. Sie sind nicht so bekannt, weil sie nicht so einfach herzustellen waren (die klassische Synthese braucht eine hohe Temperatur bis 2000°C, und oft toxische Reaktionsmittel). Trotzdem sind sie sehr interessante Materialien, weil sie auf der Grenze zwischen reinen Metallen und reinen keramischen Materialien hinsichtlich der Eigenschaften liegen. Das heißt, sie sind z.B. sehr fest, aber auch leitend, sie haben einen hohen Schmelzpunkt und sind magnetisch, etc. Durch die hier vorgestellte Forschung wird die Synthese dieser Materialien einfacher gemacht, bei niedrigen Temperaturen, mit natürlichen Produkten (z.B. Harnstoff, Gelatine, Agar, Zellulose, etc). Die Eigenschaften und Anwendungsmöglichkeiten dieser Systeme wurden auch studiert, ebenso wie die Kontrolle der Größe und Form. So konnten wir sphärische, rohrförmige, und fiber-basierte Nanostrukturen synthetisieren, aber sogar Blätter und Holz konnten als Reaktionsmittel benutzt werden und in Nitrid und Carbid umgewandelt werden, ohne die Form zu ändern. Weil die Synthese dieser Materialien direkt gemacht werden konnte, ist prinzipiell jede weitere Modifikation, Kombination und Manipulation möglich. So können jetzt neue Systeme entworfen werden. KW - metal carbides KW - metal nitrides KW - nanostructures KW - sol-gel KW - Metallnitride KW - Metallcarbide KW - Nanostrukturen KW - Sol-Gel Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-75375 ER - TY - JOUR A1 - Metzler, Ralf A1 - Jeon, Jae-Hyung A1 - Cherstvy, Andrey G. A1 - Barkai, Eli T1 - Anomalous diffusion models and their properties BT - non-stationarity, non-ergodicity, and ageing at the centenary of single particle tracking JF - physical chemistry, chemical physics : PCCP N2 - Modern microscopic techniques following the stochastic motion of labelled tracer particles have uncovered significant deviations from the laws of Brownian motion in a variety of animate and inanimate systems. Such anomalous diffusion can have different physical origins, which can be identified from careful data analysis. In particular, single particle tracking provides the entire trajectory of the traced particle, which allows one to evaluate different observables to quantify the dynamics of the system under observation. We here provide an extensive overview over different popular anomalous diffusion models and their properties. We pay special attention to their ergodic properties, highlighting the fact that in several of these models the long time averaged mean squared displacement shows a distinct disparity to the regular, ensemble averaged mean squared displacement. In these cases, data obtained from time averages cannot be interpreted by the standard theoretical results for the ensemble averages. Here we therefore provide a comparison of the main properties of the time averaged mean squared displacement and its statistical behaviour in terms of the scatter of the amplitudes between the time averages obtained from different trajectories. We especially demonstrate how anomalous dynamics may be identified for systems, which, on first sight, appear to be Brownian. Moreover, we discuss the ergodicity breaking parameters for the different anomalous stochastic processes and showcase the physical origins for the various behaviours. This Perspective is intended as a guidebook for both experimentalists and theorists working on systems, which exhibit anomalous diffusion. KW - intermittent chaotic systems KW - Fokker-Planck equations KW - time random-walks KW - fluorescence photobleaching recovery KW - fluctuation-dissipation theorem KW - fractional dynamics approach KW - photon-counting statistics KW - weak ergodicity breaking KW - flight search patterns KW - levy flights Y1 - 2014 U6 - https://doi.org/10.1039/c4cp03465a SN - 1463-9076 SN - 1463-9084 VL - 2014 IS - 16 SP - 24128 EP - 24164 ER - TY - GEN A1 - Metzler, Ralf A1 - Jeon, Jae-Hyung A1 - Cherstvy, Andrey G. A1 - Barkai, Eli T1 - Anomalous diffusion models and their properties BT - non-stationarity, non-ergodicity, and ageing at the centenary of single particle tracking N2 - Modern microscopic techniques following the stochastic motion of labelled tracer particles have uncovered significant deviations from the laws of Brownian motion in a variety of animate and inanimate systems. Such anomalous diffusion can have different physical origins, which can be identified from careful data analysis. In particular, single particle tracking provides the entire trajectory of the traced particle, which allows one to evaluate different observables to quantify the dynamics of the system under observation. We here provide an extensive overview over different popular anomalous diffusion models and their properties. We pay special attention to their ergodic properties, highlighting the fact that in several of these models the long time averaged mean squared displacement shows a distinct disparity to the regular, ensemble averaged mean squared displacement. In these cases, data obtained from time averages cannot be interpreted by the standard theoretical results for the ensemble averages. Here we therefore provide a comparison of the main properties of the time averaged mean squared displacement and its statistical behaviour in terms of the scatter of the amplitudes between the time averages obtained from different trajectories. We especially demonstrate how anomalous dynamics may be identified for systems, which, on first sight, appear to be Brownian. Moreover, we discuss the ergodicity breaking parameters for the different anomalous stochastic processes and showcase the physical origins for the various behaviours. This Perspective is intended as a guidebook for both experimentalists and theorists working on systems, which exhibit anomalous diffusion. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 174 KW - Fokker-Planck equations KW - flight search patterns KW - fluctuation-dissipation theorem KW - fluorescence photobleaching recovery KW - fractional dynamics approach KW - intermittent chaotic systems KW - levy flights KW - photon-counting statistics KW - time random-walks KW - weak ergodicity breaking Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74448 SP - 24128 EP - 24164 ER - TY - JOUR A1 - Wessig, Pablo A1 - Gerngroß, Maik A1 - Pape, Simon A1 - Bruhns, Philipp A1 - Weber, Jens T1 - Novel porous materials based on oligospiroketals (OSK) JF - RSC Advances : an international journal to further the chemical sciences N2 - New porous materials based on covalently connected monomers are presented. The key step of the synthesis is an acetalisation reaction. In previous years we used acetalisation reactions extensively to build up various molecular rods. Based on this approach, investigations towards porous polymeric materials were conducted by us. Here we wish to present the results of these studies in the synthesis of 1D polyacetals and porous 3D polyacetals. By scrambling experiments with 1D acetals we could prove that exchange reactions occur between different building blocks (evidenced by MALDI-TOF mass spectrometry). Based on these results we synthesized porous 3D polyacetals under the same mild conditions. KW - microporous organic polymers KW - molecular rods KW - construction KW - frameworks KW - membranes KW - sorption KW - models Y1 - 2014 U6 - https://doi.org/10.1039/c4ra04437a SN - 2046-2069 VL - 2014 IS - 4 SP - 31123 EP - 31129 ER - TY - GEN A1 - Wessig, Pablo A1 - Gerngroß, Maik A1 - Pape, Simon A1 - Bruhns, Philipp A1 - Weber, Jens T1 - Novel porous materials based on oligospiroketals (OSK) N2 - New porous materials based on covalently connected monomers are presented. The key step of the synthesis is an acetalisation reaction. In previous years we used acetalisation reactions extensively to build up various molecular rods. Based on this approach, investigations towards porous polymeric materials were conducted by us. Here we wish to present the results of these studies in the synthesis of 1D polyacetals and porous 3D polyacetals. By scrambling experiments with 1D acetals we could prove that exchange reactions occur between different building blocks (evidenced by MALDI-TOF mass spectrometry). Based on these results we synthesized porous 3D polyacetals under the same mild conditions. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 175 KW - construction KW - frameworks KW - membranes KW - microporous organic polymers KW - models KW - molecular rods KW - sorption Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74466 SP - 31123 EP - 31129 ER - TY - JOUR A1 - Zamponi, Flavio A1 - Penfold, Thomas J. A1 - Nachtegaal, Maarten A1 - Lübcke, Andrea A1 - Rittmann, Jochen A1 - Milne, Chris J. A1 - Chergui, Majed A1 - van Bokhoven, Jeroen A. T1 - Probing the dynamics of plasmon-excited hexanethiol-capped gold nanoparticles by picosecond X-ray absorption spectroscopy JF - physical chemistry, chemical physics : PCCP N2 - Picosecond X-ray absorption spectroscopy (XAS) is used to investigate the electronic and structural dynamics initiated by plasmon excitation of 1.8 nm diameter Au nanoparticles (NPs) functionalised with 1-hexanethiol. We show that 100 ps after photoexcitation the transient XAS spectrum is consistent with an 8% expansion of the Au–Au bond length and a large increase in disorder associated with melting of the NPs. Recovery of the ground state occurs with a time constant of ∼1.8 ns, arising from thermalisation with the environment. Simulations reveal that the transient spectrum exhibits no signature of charge separation at 100 ps and allows us to estimate an upper limit for the quantum yield (QY) of this process to be <0.1. KW - TiO2 nanoparticles KW - diimine-complexes KW - electron-transfer KW - supported gold KW - visible-light KW - water KW - surface KW - reactivity KW - nanoclusters KW - excitation Y1 - 2014 U6 - https://doi.org/10.1039/c4cp03301a SN - 1463-9076 SN - 1463-9084 VL - 2014 IS - 16 SP - 23157 EP - 23163 ER - TY - GEN A1 - Zamponi, Flavio A1 - Penfold, Thomas J. A1 - Nachtegaal, Maarten A1 - Lübcke, Andrea A1 - Rittmann, Jochen A1 - Milne, Chris J. A1 - Chergui, Majed A1 - van Bokhoven, Jeroen A. T1 - Probing the dynamics of plasmon-excited hexanethiol-capped gold nanoparticles by picosecond X-ray absorption spectroscopy N2 - Picosecond X-ray absorption spectroscopy (XAS) is used to investigate the electronic and structural dynamics initiated by plasmon excitation of 1.8 nm diameter Au nanoparticles (NPs) functionalised with 1-hexanethiol. We show that 100 ps after photoexcitation the transient XAS spectrum is consistent with an 8% expansion of the Au–Au bond length and a large increase in disorder associated with melting of the NPs. Recovery of the ground state occurs with a time constant of ∼1.8 ns, arising from thermalisation with the environment. Simulations reveal that the transient spectrum exhibits no signature of charge separation at 100 ps and allows us to estimate an upper limit for the quantum yield (QY) of this process to be <0.1. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 176 KW - TiO2 nanoparticles KW - diimine-complexes KW - electron-transfer KW - excitation KW - nanoclusters KW - reactivity KW - supported gold KW - surface KW - visible-light KW - water Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74492 SP - 23157 EP - 23163 ER - TY - GEN A1 - Cherstvy, Andrey G. A1 - Chechkin, Aleksei V. A1 - Metzler, Ralf T1 - Particle invasion, survival, and non-ergodicity in 2D diffusion processes with space-dependent diffusivity N2 - We study the thermal Markovian diffusion of tracer particles in a 2D medium with spatially varying diffusivity D(r), mimicking recently measured, heterogeneous maps of the apparent diffusion coefficient in biological cells. For this heterogeneous diffusion process (HDP) we analyse the mean squared displacement (MSD) of the tracer particles, the time averaged MSD, the spatial probability density function, and the first passage time dynamics from the cell boundary to the nucleus. Moreover we examine the non-ergodic properties of this process which are important for the correct physical interpretation of time averages of observables obtained from single particle tracking experiments. From extensive computer simulations of the 2D stochastic Langevin equation we present an in-depth study of this HDP. In particular, we find that the MSDs along the radial and azimuthal directions in a circular domain obey anomalous and Brownian scaling, respectively. We demonstrate that the time averaged MSD stays linear as a function of the lag time and the system thus reveals a weak ergodicity breaking. Our results will enable one to rationalise the diffusive motion of larger tracer particles such as viruses or submicron beads in biological cells. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 168 KW - adenoassociated virus KW - anomalous diffusion KW - cytoplasm KW - endosomal escape KW - escherichia-coli KW - infection pathway KW - intracellular-transport KW - living cells KW - models KW - trafficking Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74021 IS - 168 SP - 1591 EP - 1601 ER - TY - JOUR A1 - Meyer, Sören A1 - Matissek, M. A1 - Müller, Sandra Marie A1 - Taleshi, M. S. A1 - Ebert, Franziska A1 - Francesconi, Kevin A. A1 - Schwerdtle, Tanja T1 - In vitro toxicological characterisation of three arsenic-containing hydrocarbons JF - Metallomics N2 - Arsenic-containing hydrocarbons are one group of fat-soluble organic arsenic compounds (arsenolipids) found in marine fish and other seafood. A risk assessment of arsenolipids is urgently needed, but has not been possible because of the total lack of toxicological data. In this study the cellular toxicity of three arsenic-containing hydrocarbons was investigated in cultured human bladder (UROtsa) and liver (HepG2) cells. Cytotoxicity of the arsenic-containing hydrocarbons was comparable to that of arsenite, which was applied as the toxic reference arsenical. A large cellular accumulation of arsenic, as measured by ICP-MS/MS, was observed after incubation of both cell lines with the arsenolipids. Moreover, the toxic mode of action shown by the three arsenic-containing hydrocarbons seemed to differ from that observed for arsenite. Evidence suggests that the high cytotoxic potential of the lipophilic arsenicals results from a decrease in the cellular energy level. This first in vitro based risk assessment cannot exclude a risk to human health related to the presence of arsenolipids in seafood, and indicates the urgent need for further toxicity studies in experimental animals to fully assess this possible risk. KW - cod-liver KW - human-cells KW - arsenolipids present KW - excision-repair KW - fatty-acids KW - marine oils KW - RP-HPLC KW - metabolites KW - identification KW - trivalent Y1 - 2014 U6 - https://doi.org/10.1039/c4mt00061g SN - 1756-591X SN - 1756-5901 VL - 2014 IS - 6 SP - 1023 EP - 1033 ER - TY - GEN A1 - Meyer, Sören A1 - Matissek, M. A1 - Müller, Sandra Marie A1 - Taleshi, M. S. A1 - Ebert, Franziska A1 - Francesconi, Kevin A. A1 - Schwerdtle, Tanja T1 - In vitro toxicological characterisation of three arsenic-containing hydrocarbons N2 - Arsenic-containing hydrocarbons are one group of fat-soluble organic arsenic compounds (arsenolipids) found in marine fish and other seafood. A risk assessment of arsenolipids is urgently needed, but has not been possible because of the total lack of toxicological data. In this study the cellular toxicity of three arsenic-containing hydrocarbons was investigated in cultured human bladder (UROtsa) and liver (HepG2) cells. Cytotoxicity of the arsenic-containing hydrocarbons was comparable to that of arsenite, which was applied as the toxic reference arsenical. A large cellular accumulation of arsenic, as measured by ICP-MS/MS, was observed after incubation of both cell lines with the arsenolipids. Moreover, the toxic mode of action shown by the three arsenic-containing hydrocarbons seemed to differ from that observed for arsenite. Evidence suggests that the high cytotoxic potential of the lipophilic arsenicals results from a decrease in the cellular energy level. This first in vitro based risk assessment cannot exclude a risk to human health related to the presence of arsenolipids in seafood, and indicates the urgent need for further toxicity studies in experimental animals to fully assess this possible risk. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 170 KW - cod-liver KW - human-cells KW - arsenolipids present KW - excision-repair KW - fatty-acids KW - marine oils KW - RP-HPLC KW - metabolites KW - identification KW - trivalent Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74201 SP - 1023 EP - 1033 ER - TY - JOUR A1 - Unterberg, Marlies A1 - Leffers, Larissa A1 - Hübner, Florian A1 - Humpf, Hans-Ulrich A1 - Lepikhov, Konstantin A1 - Walter, Jörn A1 - Ebert, Franziska A1 - Schwerdtle, Tanja T1 - Toxicity of arsenite and thio-DMAV after long-term (21 days) incubation of human urothelial cells: cytotoxicity, genotoxicity and epigenetics JF - Toxicology Research N2 - This study aims to further mechanistically understand toxic modes of action after chronic inorganic arsenic exposure. Therefore long-term incubation studies in cultured cells were carried out, to display chronically attained changes, which cannot be observed in the generally applied in vitro short-term incubation studies. Particularly, the cytotoxic, genotoxic and epigenetic effects of an up to 21 days incubation of human urothelial (UROtsa) cells with pico- to nanomolar concentrations of iAsIII and its metabolite thio-DMAV were compared. After 21 days of incubation, cytotoxic effects were strongly enhanced in the case of iAsIII and might partly be due to glutathione depletion and genotoxic effects on the chromosomal level. These results are in strong contrast to cells exposed to thio-DMAV. Thus, cells seemed to be able to adapt to this arsenical, as indicated among others by an increase in the cellular glutathione level. Most interestingly, picomolar concentrations of both iAsIII and thio-DMAV caused global DNA hypomethylation in UROtsa cells, which was quantified in parallel by 5-medC immunostaining and a newly established, reliable, high resolution mass spectrometry (HRMS)-based test system. This is the first time that epigenetic effects are reported for thio-DMAV; iAsIII induced epigenetic effects occur in at least 8000 fold lower concentrations as reported in vitro before. The fact that both arsenicals cause DNA hypomethylation at really low, exposure-relevant concentrations in human urothelial cells suggests that this epigenetic effect might contribute to inorganic arsenic induced carcinogenicity, which for sure has to be further investigated in future studies. KW - induced malignant-transformation KW - genomic dna methylation KW - vitro toxicological characterization KW - thio-dimethylarsinic acid KW - bladder-cancer KW - methyltransferases dnmt3a KW - cytosine methylation KW - carcinogen exposure KW - mass-spectrometry KW - gene-expression Y1 - 2014 SN - 2045-4538 SN - 2045-452X VL - 3 IS - 6 SP - 456 EP - 464 PB - Royal Society of Chemistry CY - Cambridge ER - TY - GEN A1 - Unterberg, Marlies A1 - Leffers, Larissa A1 - Hübner, Florian A1 - Humpf, Hans-Ulrich A1 - Lepikhov, Konstantin A1 - Walter, Jörn A1 - Ebert, Franziska A1 - Schwerdtle, Tanja T1 - Toxicity of arsenite and thio-DMAV after long-term (21 days) incubation of human urothelial cells: cytotoxicity, genotoxicity and epigenetics N2 - This study aims to further mechanistically understand toxic modes of action after chronic inorganic arsenic exposure. Therefore long-term incubation studies in cultured cells were carried out, to display chronically attained changes, which cannot be observed in the generally applied in vitro short-term incubation studies. Particularly, the cytotoxic, genotoxic and epigenetic effects of an up to 21 days incubation of human urothelial (UROtsa) cells with pico- to nanomolar concentrations of iAsIII and its metabolite thio-DMAV were compared. After 21 days of incubation, cytotoxic effects were strongly enhanced in the case of iAsIII and might partly be due to glutathione depletion and genotoxic effects on the chromosomal level. These results are in strong contrast to cells exposed to thio-DMAV. Thus, cells seemed to be able to adapt to this arsenical, as indicated among others by an increase in the cellular glutathione level. Most interestingly, picomolar concentrations of both iAsIII and thio-DMAV caused global DNA hypomethylation in UROtsa cells, which was quantified in parallel by 5-medC immunostaining and a newly established, reliable, high resolution mass spectrometry (HRMS)-based test system. This is the first time that epigenetic effects are reported for thio-DMAV; iAsIII induced epigenetic effects occur in at least 8000 fold lower concentrations as reported in vitro before. The fact that both arsenicals cause DNA hypomethylation at really low, exposure-relevant concentrations in human urothelial cells suggests that this epigenetic effect might contribute to inorganic arsenic induced carcinogenicity, which for sure has to be further investigated in future studies. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 178 KW - induced malignant-transformation KW - genomic dna methylation KW - vitro toxicological characterization KW - thio-dimethylarsinic acid KW - bladder-cancer KW - methyltransferases dnmt3a KW - cytosine methylation KW - carcinogen exposure KW - mass-spectrometry KW - gene-expression Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-76239 SP - 456 EP - 464 ER - TY - JOUR A1 - Pieper, Imke A1 - Wehe, Christoph A. A1 - Bornhorst, Julia A1 - Ebert, Franziska A1 - Leffers, Larissa A1 - Holtkamp, Michael A1 - Höseler, Pia A1 - Weber, Till A1 - Mangerich, Aswin A1 - Bürkle, Alexander A1 - Karst, Uwe A1 - Schwerdtle, Tanja T1 - Mechanisms of Hg species induced toxicity in cultured human astrocytes BT - genotoxicity and DNA-damage response JF - Metallomics N2 - The toxicologically most relevant mercury (Hg) species for human exposure is methylmercury (MeHg). Thiomersal is a common preservative used in some vaccine formulations. The aim of this study is to get further mechanistic insight into the yet not fully understood neurotoxic modes of action of organic Hg species. Mercury species investigated include MeHgCl and thiomersal. Additionally HgCl2 was studied, since in the brain mercuric Hg can be formed by dealkylation of the organic species. As a cellular system astrocytes were used. In vivo astrocytes provide the environment necessary for neuronal function. In the present study, cytotoxic effects of the respective mercuricals increased with rising alkylation level and correlated with their cellular bioavailability. Further experiments revealed for all species at subcytotoxic concentrations no induction of DNA strand breaks, whereas all species massively increased H2O2-induced DNA strand breaks. This co-genotoxic effect is likely due to a disturbance of the cellular DNA damage response. Thus, at nanomolar, sub-cytotoxic concentrations, all three mercury species strongly disturbed poly(ADP-ribosyl)ation, a signalling reaction induced by DNA strand breaks. Interestingly, the molecular mechanism behind this inhibition seems to be different for the species. Since chronic PARP-1 inhibition is also discussed to sacrifice neurogenesis and learning abilities, further experiments on neurons and in vivo studies could be helpful to clarify whether the inhibition of poly(ADP-ribosyl)ation contributes to organic Hg induced neurotoxicity. KW - cell-death KW - poly(ADP-ribose) polymerase-1 KW - neurodegenerative diseases KW - adduct formation KW - thimerosal KW - methylmercury KW - repair KW - neurotoxicity KW - manganese KW - exposure Y1 - 2014 U6 - https://doi.org/10.1039/c3mt00337j SN - 1756-591X SN - 1756-5901 VL - 2014 IS - 6 SP - 662 EP - 671 ER - TY - GEN A1 - Pieper, Imke A1 - Wehe, Christoph A. A1 - Bornhorst, Julia A1 - Ebert, Franziska A1 - Leffers, Larissa A1 - Holtkamp, Michael A1 - Höseler, Pia A1 - Weber, Till A1 - Mangerich, Aswin A1 - Bürkle, Alexander A1 - Karst, Uwe A1 - Schwerdtle, Tanja T1 - Mechanisms of Hg species induced toxicity in cultured human astrocytes BT - genotoxicity and DNA-damage response N2 - The toxicologically most relevant mercury (Hg) species for human exposure is methylmercury (MeHg). Thiomersal is a common preservative used in some vaccine formulations. The aim of this study is to get further mechanistic insight into the yet not fully understood neurotoxic modes of action of organic Hg species. Mercury species investigated include MeHgCl and thiomersal. Additionally HgCl2 was studied, since in the brain mercuric Hg can be formed by dealkylation of the organic species. As a cellular system astrocytes were used. In vivo astrocytes provide the environment necessary for neuronal function. In the present study, cytotoxic effects of the respective mercuricals increased with rising alkylation level and correlated with their cellular bioavailability. Further experiments revealed for all species at subcytotoxic concentrations no induction of DNA strand breaks, whereas all species massively increased H2O2-induced DNA strand breaks. This co- genotoxic effect is likely due to a disturbance of the cellular DNA damage response. Thus, at nanomolar, sub-cytotoxic concentrations, all three mercury species strongly disturbed poly(ADP-ribosyl)ation, a signalling reaction induced by DNA strand breaks. Interestingly, the molecular mechanism behind this inhibition seems to be different for the species. Since chronic PARP-1 inhibition is also discussed to sacrifice neurogenesis and learning abilities, further experiments on neurons and in vivo studies could be helpful to clarify whether the inhibition of poly(ADP-ribosyl) ation contributes to organic Hg induced neurotoxicity. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - paper 171 KW - adduct formation KW - cell-death KW - exposure KW - manganese KW - methylmercury KW - neurodegenerative diseases KW - neurotoxicity KW - poly(ADP-ribose) polymerase-1 KW - repair KW - thimerosal Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-74379 SP - 662 EP - 671 ER - TY - THES A1 - Gerngroß, Maik T1 - Untersuchungen zur Herstellung poröser Materialien durch Acetalisierungsreaktionen Y1 - 2014 ER - TY - JOUR A1 - Ghosh, Surya K. A1 - Cherstvy, Andrey G. A1 - Metzler, Ralf ED - Metzler, Ralf T1 - Non-universal tracer diffusion in crowded media of non-inert obstacles JF - Physical Chemistry Chemical Physics N2 - We study the diffusion of a tracer particle, which moves in continuum space between a lattice of excluded volume, immobile non-inert obstacles. In particular, we analyse how the strength of the tracer–obstacle interactions and the volume occupancy of the crowders alter the diffusive motion of the tracer. From the details of partitioning of the tracer diffusion modes between trapping states when bound to obstacles and bulk diffusion, we examine the degree of localisation of the tracer in the lattice of crowders. We study the properties of the tracer diffusion in terms of the ensemble and time averaged mean squared displacements, the trapping time distributions, the amplitude variation of the time averaged mean squared displacements, and the non-Gaussianity parameter of the diffusing tracer. We conclude that tracer–obstacle adsorption and binding triggers a transient anomalous diffusion. From a very narrow spread of recorded individual time averaged trajectories we exclude continuous type random walk processes as the underlying physical model of the tracer diffusion in our system. For moderate tracer–crowder attraction the motion is found to be fully ergodic, while at stronger attraction strength a transient disparity between ensemble and time averaged mean squared displacements occurs. We also put our results into perspective with findings from experimental single-particle tracking and simulations of the diffusion of tagged tracers in dense crowded suspensions. Our results have implications for the diffusion, transport, and spreading of chemical components in highly crowded environments inside living cells and other structured liquids. KW - fluorescence correlation spectroscopy KW - single-particle tracking KW - anomalous diffusion KW - living cells KW - physiological consequences KW - langevin equation KW - infection pathway KW - excluded volume KW - brownian-motion KW - random-walks Y1 - 2014 SN - 1463-9076 VL - 3 IS - 17 SP - 1847 EP - 1858 PB - The Royal Society of Chemistry CY - Cambridge ER - TY - GEN A1 - Ghosh, Surya K. A1 - Cherstvy, Andrey G. A1 - Metzler, Ralf T1 - Non-universal tracer diffusion in crowded media of non-inert obstacles N2 - We study the diffusion of a tracer particle, which moves in continuum space between a lattice of excluded volume, immobile non-inert obstacles. In particular, we analyse how the strength of the tracer–obstacle interactions and the volume occupancy of the crowders alter the diffusive motion of the tracer. From the details of partitioning of the tracer diffusion modes between trapping states when bound to obstacles and bulk diffusion, we examine the degree of localisation of the tracer in the lattice of crowders. We study the properties of the tracer diffusion in terms of the ensemble and time averaged mean squared displacements, the trapping time distributions, the amplitude variation of the time averaged mean squared displacements, and the non-Gaussianity parameter of the diffusing tracer. We conclude that tracer–obstacle adsorption and binding triggers a transient anomalous diffusion. From a very narrow spread of recorded individual time averaged trajectories we exclude continuous type random walk processes as the underlying physical model of the tracer diffusion in our system. For moderate tracer–crowder attraction the motion is found to be fully ergodic, while at stronger attraction strength a transient disparity between ensemble and time averaged mean squared displacements occurs. We also put our results into perspective with findings from experimental single-particle tracking and simulations of the diffusion of tagged tracers in dense crowded suspensions. Our results have implications for the diffusion, transport, and spreading of chemical components in highly crowded environments inside living cells and other structured liquids. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 186 KW - escence correlation spectroscopy KW - single-particle tracking KW - anomalous diffusion KW - living cells KW - physiological consequences KW - langevin equation KW - infection pathway KW - excluded volume KW - brownian-motion KW - random-walks Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-77128 SP - 1847 EP - 1858 PB - The Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Shin, Jaeoh A1 - Cherstvy, Andrey G. A1 - Metzler, Ralf ED - Metzler, Ralf T1 - Kinetics of polymer looping with macromolecular crowding: effects of volume fraction and crowder size JF - Soft Matter N2 - The looping of polymers such as DNA is a fundamental process in the molecular biology of living cells, whose interior is characterised by a high degree of molecular crowding. We here investigate in detail the looping dynamics of flexible polymer chains in the presence of different degrees of crowding. From the analysis of the looping–unlooping rates and the looping probabilities of the chain ends we show that the presence of small crowders typically slows down the chain dynamics but larger crowders may in fact facilitate the looping. We rationalise these non-trivial and often counterintuitive effects of the crowder size on the looping kinetics in terms of an effective solution viscosity and standard excluded volume. It is shown that for small crowders the effect of an increased viscosity dominates, while for big crowders we argue that confinement effects (caging) prevail. The tradeoff between both trends can thus result in the impediment or facilitation of polymer looping, depending on the crowder size. We also examine how the crowding volume fraction, chain length, and the attraction strength of the contact groups of the polymer chain affect the looping kinetics and hairpin formation dynamics. Our results are relevant for DNA looping in the absence and presence of protein mediation, DNA hairpin formation, RNA folding, and the folding of polypeptide chains under biologically relevant high-crowding conditions. KW - gene-regulation kinetics KW - physiological consequences KW - spatial-organization KW - anomalous diffusion KW - folding kinetics KW - living cells KW - dna coiling KW - in-vitro KW - dynamics KW - mixtures Y1 - 2014 SN - 1744-683X SP - 472 EP - 488 PB - The Royal Society of Chemistry CY - Cambridge ER - TY - GEN A1 - Shin, Jaeoh A1 - Cherstvy, Andrey G. A1 - Metzler, Ralf T1 - Kinetics of polymer looping with macromolecular crowding: effects of volume fraction and crowder size N2 - The looping of polymers such as DNA is a fundamental process in the molecular biology of living cells, whose interior is characterised by a high degree of molecular crowding. We here investigate in detail the looping dynamics of flexible polymer chains in the presence of different degrees of crowding. From the analysis of the looping–unlooping rates and the looping probabilities of the chain ends we show that the presence of small crowders typically slows down the chain dynamics but larger crowders may in fact facilitate the looping. We rationalise these non-trivial and often counterintuitive effects of the crowder size on the looping kinetics in terms of an effective solution viscosity and standard excluded volume. It is shown that for small crowders the effect of an increased viscosity dominates, while for big crowders we argue that confinement effects (caging) prevail. The tradeoff between both trends can thus result in the impediment or facilitation of polymer looping, depending on the crowder size. We also examine how the crowding volume fraction, chain length, and the attraction strength of the contact groups of the polymer chain affect the looping kinetics and hairpin formation dynamics. Our results are relevant for DNA looping in the absence and presence of protein mediation, DNA hairpin formation, RNA folding, and the folding of polypeptide chains under biologically relevant high-crowding conditions. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 185 KW - gene-regulation kinetics KW - physiological consequences KW - spatial-organization KW - anomalous diffusion KW - folding kinetics KW - living cells KW - dna coiling KW - in-vitro KW - dynamics KW - mixtures Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-76961 SP - 472 EP - 488 PB - The Royal Society of Chemistry CY - Cambridge ER - TY - THES A1 - Klaper, Matthias T1 - Untersuchungen zum intramolekularen Transfer von Singulettsauerstoff auf Acene und Alkene Y1 - 2014 ER - TY - THES A1 - Faivre, Damien T1 - Biological and biomimetic formation and organization of magnetic nanoparticles T1 - Biologische und biomimetische Bildung und Anordnung von magnetischen Nanopartikel N2 - Biological materials have ever been used by humans because of their remarkable properties. This is surprising since the materials are formed under physiological conditions and with commonplace constituents. Nature thus not only provides us with inspiration for designing new materials but also teaches us how to use soft molecules to tune interparticle and external forces to structure and assemble simple building blocks into functional entities. Magnetotactic bacteria and their chain of magnetosomes represent a striking example of such an accomplishment where a very simple living organism controls the properties of inorganics via organics at the nanometer-scale to form a single magnetic dipole that orients the cell in the Earth magnetic field lines. My group has developed a biological and a bio-inspired research based on these bacteria. My research, at the interface between chemistry, materials science, physics, and biology focuses on how biological systems synthesize, organize and use minerals. We apply the design principles to sustainably form hierarchical materials with controlled properties that can be used e.g. as magnetically directed nanodevices towards applications in sensing, actuating, and transport. In this thesis, I thus first present how magnetotactic bacteria intracellularly form magnetosomes and assemble them in chains. I developed an assay, where cells can be switched from magnetic to non-magnetic states. This enabled to study the dynamics of magnetosome and magnetosome chain formation. We found that the magnetosomes nucleate within minutes whereas chains assembles within hours. Magnetosome formation necessitates iron uptake as ferrous or ferric ions. The transport of the ions within the cell leads to the formation of a ferritin-like intermediate, which subsequently is transported and transformed within the magnetosome organelle in a ferrihydrite-like precursor. Finally, magnetite crystals nucleate and grow toward their mature dimension. In addition, I show that the magnetosome assembly displays hierarchically ordered nano- and microstructures over several levels, enabling the coordinated alignment and motility of entire populations of cells. The magnetosomes are indeed composed of structurally pure magnetite. The organelles are partly composed of proteins, which role is crucial for the properties of the magnetosomes. As an example, we showed how the protein MmsF is involved in the control of magnetosome size and morphology. We have further shown by 2D X-ray diffraction that the magnetosome particles are aligned along the same direction in the magnetosome chain. We then show how magnetic properties of the nascent magnetosome influence the alignment of the particles, and how the proteins MamJ and MamK coordinate this assembly. We propose a theoretical approach, which suggests that biological forces are more important than physical ones for the chain formation. All these studies thus show how magnetosome formation and organization are under strict biological control, which is associated with unprecedented material properties. Finally, we show that the magnetosome chain enables the cells to find their preferred oxygen conditions if the magnetic field is present. The synthetic part of this work shows how the understanding of the design principles of magnetosome formation enabled me to perform biomimetic synthesis of magnetite particles within the highly desired size range of 25 to 100 nm. Nucleation and growth of such particles are based on aggregation of iron colloids termed primary particles as imaged by cryo-high resolution TEM. I show how additives influence magnetite formation and properties. In particular, MamP, a so-called magnetochrome proteins involved in the magnetosome formation in vivo, enables the in vitro formation of magnetite nanoparticles exclusively from ferrous iron by controlling the redox state of the process. Negatively charged additives, such as MamJ, retard magnetite nucleation in vitro, probably by interacting with the iron ions. Other additives such as e.g. polyarginine can be used to control the colloidal stability of stable-single domain sized nanoparticles. Finally, I show how we can “glue” magnetic nanoparticles to form propellers that can be actuated and swim with the help of external magnetic fields. We propose a simple theory to explain the observed movement. We can use the theoretical framework to design experimental conditions to sort out the propellers depending on their size and effectively confirm this prediction experimentally. Thereby, we could image propellers with size down to 290 nm in their longer dimension, much smaller than what perform so far. N2 - Biologische Materialien wie Knochen, Muscheln und Holz wurden von den Menschen seit den ältesten Zeiten verwendet. Diese biologisch gebildeten Materialien haben bemerkenswerte Eigenschaften. Dies ist besonders überraschend, da sie unter physiologischen Bedingungen und mit alltäglichen Bestandteilen gebildet sind. Die Natur liefert uns also nicht nur mit Inspiration für die Entwicklung neuer Materialien, sondern lehrt uns auch, wie biologische Additiven benutzen werden können, um einfache synthetische Bausteine in funktionale Einheiten zu strukturieren. Magnetotaktischen Bakterien und ihre Kette von Magnetosomen sind ein Beispiel, wo einfache Lebewesen die Eigenschaften von anorganischen Materialien steuern, um sich entlang den magnetischen Feldlinien der Erde zu orientieren. Die von den Bakterien gebildeten Magnetosomen sind von besonderem Interesse, da mit magnetischen Eisenoxid-Nanopartikeln in den letzten zehn Jahren einer Vielzahl von Bio-und nanotechnologischen Anwendungen entwickelt worden sind. In dieser Arbeit stelle ich eine biologische und eine bio-inspirierte Forschung auf der Grundlage der magnetotaktischen Bakterien vor. Diese Forschung verbindet die neuesten Entwicklungen von Nanotechnik in der chemischen Wissenschaft, die neuesten Fortschritte der Molekularbiologie zusammen mit modernen Messverfahren. Mein Forschungsschwerpunkt liegt somit an der Schnittstelle zwischen Chemie, Materialwissenschaften, Physik und Biologie. Ich will verstehen, wie biologische Systeme Materialien synthetisieren und organisieren, um Design-Prinzipien zu extrahieren, damit hierarchischen Materialien mit kontrollierten Eigenschaften nachhaltig gebildet werden. KW - magnetotaktische Bakterien KW - Magnetit Nanopartikel KW - Biomineralisation KW - magnetite KW - nanoparticle KW - biomineralization KW - magnetosome KW - magnetotactic bacteria Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-72022 ER - TY - THES A1 - Ermeydan, Mahmut Ali T1 - Wood cell wall modification with hydrophobic molecules T1 - Modifikation von Holzzellwänden durch hydrophobe Moleküle N2 - Wood is used for many applications because of its excellent mechanical properties, relative abundance and as it is a renewable resource. However, its wider utilization as an engineering material is limited because it swells and shrinks upon moisture changes and is susceptible to degradation by microorganisms and/or insects. Chemical modifications of wood have been shown to improve dimensional stability, water repellence and/or durability, thus increasing potential service-life of wood materials. However current treatments are limited because it is difficult to introduce and fix such modifications deep inside the tissue and cell wall. Within the scope of this thesis, novel chemical modification methods of wood cell walls were developed to improve both dimensional stability and water repellence of wood material. These methods were partly inspired by the heartwood formation in living trees, a process, that for some species results in an insertion of hydrophobic chemical substances into the cell walls of already dead wood cells, In the first part of this thesis a chemistry to modify wood cell walls was used, which was inspired by the natural process of heartwood formation. Commercially available hydrophobic flavonoid molecules were effectively inserted in the cell walls of spruce, a softwood species with low natural durability, after a tosylation treatment to obtain “artificial heartwood”. Flavonoid inserted cell walls show a reduced moisture absorption, resulting in better dimensional stability, water repellency and increased hardness. This approach was quite different compared to established modifications which mainly address hydroxyl groups of cell wall polymers with hydrophilic substances. In the second part of the work in-situ styrene polymerization inside the tosylated cell walls was studied. It is known that there is a weak adhesion between hydrophobic polymers and hydrophilic cell wall components. The hydrophobic styrene monomers were inserted into the tosylated wood cell walls for further polymerization to form polystyrene in the cell walls, which increased the dimensional stability of the bulk wood material and reduced water uptake of the cell walls considerably when compared to controls. In the third part of the work, grafting of another hydrophobic and also biodegradable polymer, poly(ɛ-caprolactone) in the wood cell walls by ring opening polymerization of ɛ-caprolactone was studied at mild temperatures. Results indicated that polycaprolactone attached into the cell walls, caused permanent swelling of the cell walls up to 5%. Dimensional stability of the bulk wood material increased 40% and water absorption reduced more than 35%. A fully biodegradable and hydrophobized wood material was obtained with this method which reduces disposal problem of the modified wood materials and has improved properties to extend the material’s service-life. Starting from a bio-inspired approach which showed great promise as an alternative to standard cell wall modifications we showed the possibility of inserting hydrophobic molecules in the cell walls and supported this fact with in-situ styrene and ɛ-caprolactone polymerization into the cell walls. It was shown in this thesis that despite the extensive knowledge and long history of using wood as a material there is still room for novel chemical modifications which could have a high impact on improving wood properties. N2 - Der nachwachsende Rohstoff Holz wird aufgrund seiner guten mechanischen Eigenschaften und der leichten Verfügbarkeit für viele Anwendungszwecke genutzt. Quellen und Schrumpfen bei Feuchtigkeitsänderungen des hygroskopischen Werkstoffs Holz limitieren jedoch die Einsatzmöglichkeiten. Ein weiteres Problem stellt der mitunter leichte Abbau – u.a. bei feuchtem Holz - durch Mikroorganismen und/oder Insekten dar. Durch chemische Modifizierungen können die Dimensionsstabilität, die Hydrophobizität und die Dauerhaftigkeit verbessert und damit die potentielle Lebensdauer des Werkstoffes erhöht werden. Dabei ist die dauerhafte Modifikation der Zellwand nur äußerst schwer realisierbar. Inspiriert von der Kernholzbildung in lebenden Bäumen, ein zellwandverändernder Prozess, der Jahre nach der Holzbildung erfolgt, wurden im Rahmen dieser Arbeit neue Ansätze zur chemischen Modifizierung der Zellwände entwickelt, um die Dimensionsstabilität und Hydrophobizität zu erhöhen. Der erste Teil der Arbeit ist stark vom Prozess der Kernholzbildung inspiriert, eine abgeleitete Chemie wurde verwendet, um die Zellwände von Fichte, einem Nadelholz von geringer natürlicher Dauerhaftigkeit, zu modifizieren. Kommerziell verfügbare hydrophobe Flavonoide wurden nach einem Tosylierungsschritt erfolgreich in die Zellwand eingebracht, um so „artifizielles Kernholz“ zu erzeugen. Die modifizierten Holzproben zeigten eine verringerte Wasseraufnahme, die zu erhöhter Dimensionsstabilität und Härte führte. Dieser Ansatz unterscheidet sich grundlegend von bereits etablierten Modifikationen, die hauptsächlich hypdrophile Substanzen an die Hydroxylgruppen der Zellwand anlagern. Der zweite Teil der Arbeit beschäftigt sich mit der Polymerisation von Styren in tosylierten Zellwänden. Es ist bekannt, dass es nur eine schwache Adhäsion zwischen den hydrophoben Polymeren und den hydrophilen Zellwandkomponenten gibt. Die hydrophoben Styren-Monomere wurden in die tosylierte Zellwand eingebracht und zu Polystyren polymerisiert. Wie bei der Modifikation mit Flavonoiden konnte eine erhöhte Dimensionsstabilität und reduzierte Wasseraufnahme der Zellwände beobachtet werden. Im dritten Teil der Arbeit wurde das biologisch abbaubare, hydrophobe poly(ɛ-caprolacton) in der Zellwand aufpolymerisiert. Die Ergebnisse deuten darauf hin, dass Polycaprolacton in der Zellwand gebunden ist und zu einer permanenten Quellung führt (bis zu 5 %). Die Dimensionsstabilität nahm um 40 % zu und die Wasseraufnahmerate konnte um mehr als 35 % reduziert werden. Mit dieser Methode kann nicht nur dimensionsstabileres Holz realisiert werden, auch biologische Abbaubarkeit und damit eine einfache Entsorgung sind gewährleistest. KW - Holzmodifikation KW - hydrophobe Moleküle KW - Dimensionsstabilität KW - Wassergehalt KW - wood modification KW - hydrophobic molecules KW - dimensional stability KW - moisture content Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-71325 ER - TY - THES A1 - Berdzinski, Stefan T1 - Photoinduzierte radikalische Polymerisation in ionischen Flüssigkeiten und der Einfluss der Radikalrekombination T1 - Photoinduced radical polymerization in ionic liquids and the influence of the radical recombination N2 - Die vorliegende Arbeit behandelt Untersuchungen zum Einfluss ionischer Flüssigkeiten sowohl auf den Rekombinationsprozess photolytisch generierter Lophylradikale als auch auf die photoinduzierte Polymerisation. Im Fokus standen hierbei pyrrolidiniumbasierte ionische Flüssigkeiten sowie polymerisierbare imidazoliumbasierte ionische Flüssigkeiten. Mittels UV-Vis-Spektroskopie wurde in den ionischen Flüssigkeiten im Vergleich zu ausgewählten organischen Lösungsmitteln die Rekombinationskinetik der aus o-Cl-HABI photolytisch generierten Lophylradikale bei unterschiedlichen Temperaturen verfolgt und die Geschwindigkeitskonstanten der Radikalrekombination bestimmt. Die Charakterisierung des Rekombinationsprozesses erfolgt dabei insbesondere unter Verwendung der mittels Eyring-Gleichung ermittelten Aktivierungsparameter. Hierbei konnte gezeigt werden, dass die Rekombination der Lophylradikale in den ionischen Flüssigkeiten im Gegensatz zu den organischen Lösungsmitteln zu einem großen Anteil innerhalb des Lösungsmittelkäfigs erfolgt. Weiterhin wurden für den Einsatz von o-Cl-HABI als Radikalbildner in den photoinduzierten Polymerisationen mehrere mögliche Co-Initiatoren über photokalorimetrische Messungen untersucht. Hierbei wurde auch ein neuer Aspekt zur Kettenübertragung vom Lophylradikal auf den heterocyclischen Co-Initiator vorgestellt. Darüber hinaus wurden photoinduzierte Polymerisationen unter Einsatz eines Initiatorsystems, bestehend aus o-Cl-HABI als Radikalbildner und einem heterocyclischen Co-Initiator, in den ionischen Flüssigkeiten untersucht. Diese Untersuchungen beinhalten zum einen photokalorimetrische Messungen der photoinduzierten Polymerisation von polymerisierbaren imidazoliumbasierten ionischen Flüssigkeiten. Zum anderen wurden Untersuchungen zur photoinduzierten Polymerisation von Methylmethacrylat in pyrrolidiniumbasierten ionischen Flüssigkeiten durchgeführt. Dabei wurden Einflussparameter wie Zeit, Temperatur, Viskosität, Lösungsmittelkäfigeffekt und die Alkylkettenlänge am Kation der ionischen Flüssigkeiten auf die Ausbeuten und Molmassen sowie Molmassenverteilungen der Polymere hin untersucht. N2 - This work examined the investigation of the influence of ionic liquids on both the recombination process of photolytically generated lophyl radicals and on the photoinduced polymerization. Pyrrolidinium-based ionic liquids as well as polymerizable imidazolium-based ionic liquids were here in particular interest. Recombination kinetics of photolytically generated lophyl radicals were examined in ionic liquids and selected organic solvents at different temperatures by using UV-Vis spectroscopy. Futhermore, rate constants and activation parameters of the radical recombination were used to characterize the recombination process in these different solvents. It was be shown that the recombination of the lophyl radicals occurs in the ionic liquids to a higher extent within the solvent cage in contrast to organic solvents. Also, prolongation of the alkyl chain at the cation of the ionic liquids leads to an increase of the in cage recombination in both the pyrrolidinium based ionic liquids, as well as in the ionic liquids of the polymerizable imidazolium based ionic liquids. Furthermore, selected coinitiators were investigated for photoinduced polymerization in combination with o-Cl-HABI as radical former by using photo calorimetry. Thereby a new aspect of the chain transfer from a lophyl radical to heterocyclic co-initiator was be shown. In addition, photo-induced polymerizations in the ionic liquids were investigated using an initiator system consisting of o-Cl-HABI as the radical former and a heterocyclic co-initiator. These studies include photo-induced polymerizations of polymerizable imidazolium-based ionic liquids, which were carried out by photo callorimetry. Furthermore, photo-induced polymerizations of methyl methacrylate were investigated in pyrrolidinium-based ionic liquids. In this conection time, temperature, viscosity, solvent cage effect and the alkyl chain length at the cation of the ionic liquids were examined as influencing parameters on yield, molecular weight and molecular weight distribution of the obtained polymers. KW - freie radikalische Polymerisation KW - ionische Flüssigkeiten KW - Radikalrekombination KW - lichtinduziert KW - free radical polymerization KW - ionic liquids KW - radical recombination KW - light induced Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-72582 ER - TY - THES A1 - Budach, Dennis B. T1 - Synthese von Dendrimeren aus Oligospiroketal-Bausteinen Y1 - 2014 ER - TY - JOUR A1 - Schmidt, Joachim A1 - Bechmann, Wolfgang T1 - Zur Anwendung des Skalarprodukts von Kraft und Weg auf reversible Prozesse (Druck-Volumen-Änderung, Dehnung, Elektrostatische Wechselwirkung, Hub) T1 - To the application of the scalar product of force and displacement to reversible processes (pressure-volume change, elongation, electrostatic interaction, raising) BT - die Verwendung äußerer oder systemimmanenter Kräfte BT - the use of external or system-immanent forces N2 - Wir schlagen einen allgemein anwendbaren Algorithmus vor, der unter Verwendung des Skalarprodukts von Kraft und Weg zum richtigen Vorzeichen in den Gleichungen für die Arbeit und die Potentielle Energie bei reversiblen Prozessen (Druck-Volumen-Änderung, Dehnung, Elektrostatische Wechselwirkung, Hub)führt. Wir zeigen, dass es dabei möglich ist, systemimmanente oder externe Kräfte zu benutzen. Wir zeigen, dass bei Verwendung von systemimmanenten Kräften das Skalarprodukt mit negativem Vorzeichen anzusetzen ist. Zudem ist es sehr wichtig, nötige Vorzeichenwechsel bei den einzelnen Schritten zu beachten. Wir betonen dies, weil gelegentlich übersehen wird, dass ein Vorzeichenwechsel nötig ist, wenn das Wegdifferential ds durch das Höhendifferential dh beziehungsweise durch das Abstandsdifferential dx oder dr ersetzt werden muss. KW - Skalarprodukt von Kraft und Weg KW - systemimmanente Kräfte KW - Druck-Volumen-Änderung KW - Dehnung KW - Elektrostatische Wechselwirkung KW - Gravitation KW - scalar product of force and displacement KW - system-immanent forces KW - pressure-volume change KW - elongation KW - electrostatic interaction KW - gravitation Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-69732 ER - TY - THES A1 - Merkel, Roswitha T1 - Untersuchung zur Synthese und Eigenschaften von komplexen Oligospiroketalen T1 - Investigation of synthesis and properties of complex oligospiroketals N2 - Es ist in dieser Arbeit gelungen, starre Oligospiroketal(OSK)-Stäbe als Grundbausteine für komplexe 2D- und 3D-Systeme zu verwenden. Dazu wurde ein difunktionalisierter starrer Stab synthetisiert, der mit seines Gleichen und anderen verzweigten Funktionalisierungseinheiten in Azid-Alkin-Klickreaktionen eingesetzt wurde. An zwei über Klickreaktion verknüpften OSK-Stäben konnten mittels theoretischer Berechnungen Aussagen über die neuartige Bimodalität der Konformation getroffen werden. Es wurde dafür der Begriff Gelenkstab eingeführt, da die Moleküle um ein Gelenk gedreht sowohl gestreckt als auch geknickt vorliegen können. Aufbauend auf diesen Erkenntnissen konnte gezeigt werden, dass nicht nur gezielt große Polymere aus bis zu vier OSK-Stäben synthetisiert werden können, sondern es auch möglich ist, durch gezielte Änderung von Reaktionsbedingungen der Klickreaktion auch Cyclen aus starren OSK-Stäben herzustellen. Die neu entwickelte Substanzklasse der Gelenkstäbe wurde im Hinblick auf die Steuerung des vorliegenden Gleichgewichts zwischen geknicktem und gestrecktem Gelenkstab hin untersucht. Dafür wurde der Gelenkstab mit Pyrenylresten in terminaler Position versehen. Es wurde durch Fluoreszenzmessungen festgestellt, dass das Gleichgewicht z. B. durch die Temperatur oder die Wahl des Lösungsmittels beeinflussbar ist. Für vielfache Anwendungen wurde eine vereinfachte Synthesestrategie gefunden, mit der eine beliebige Funktionalisierung in nur einem Syntheseschritt erreicht werden konnte. Es konnten photoaktive Gelenkstäbe synthetisiert werden, die gezielt zur intramolekularen Dimerisierung geführt werden konnten. Zusätzlich wurde durch Aminosäuren ein Verknüpfungselement am Ende der Gelenkstäbe gefunden, das eine stereoselektive Synthese von Mehrfachfunktionalisierungen zulässt. Die Synthese der komplexen Gelenkstäbe wurde als ein neuartiges Gebiet aufgezeigt und bietet ein breites Forschungspotential für weitere Anwendungen z. B. in der Biologie (als molekulare Schalter für Ionentransporte) und in der Materialchemie (als Ladungs- oder Energietransporteure). N2 - In this dissertation the use of rigid Oligospiroketal (OSK)-rods as basic model for 2D- and 3D-systems was shown. For that purpose a bifunctionalized rigid rod was synthesized and was used in Azide-Alkine-clickreaction with itself and with other branched functionalized units. By theoretical calculations a statement about the novel bimodulation of the conformation of two OSK-rods which are linked by a clickreaction could be made. “Articulated rod” was introduced as new term, because the molecules could exist elongated or buckled. Based on this knowledge it became apparent that not only the size selective synthesis of polymers by using up to four OSK-rods is possible but also cycles with OSK-rods by using different click-reaction conditions can be synthesized. The newly developed group of “articulated rod” substances was examined regarding the equilibrium between buckled and elongated “articulated rod”. That for the articulated rod was functionalized with pyrenyl moieties in terminal position. By fluorescence measurements of these rods it could be shown that the equilibration is influenced by different temperatures and different solvents. For multiple applications a simplified strategy for synthesis with a wide range of functionalization in only one step of synthesis could be achieved. Photoactive articulated rods were synthesized, that could be selectively intramolecular dimerized. Additionally, amino acids were introduced as linker at the end of a articulated rod. By this a stereoselective synthesis of multiple functionaliations is possible. By the synthesis of complex articulated rods a novel field of research was found. There is a wide potential of research for more applications for example in biology (as molecular switch for transportation of ions) and in materials chemistry (as transporter for charge or energy). KW - Stab KW - Oligospiroketal KW - Klick KW - Alkin KW - Azid KW - articulated KW - rod KW - click KW - alkine KW - azide Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-72561 ER - TY - JOUR A1 - Omosa, Leonidah K. A1 - Amugune, Beatrice A1 - Ndunda, Beth A1 - Milugo, Trizah K. A1 - Heydenreich, Matthias A1 - Yenesew, Abiy A1 - Midiwo, Jacob O. T1 - Antimicrobial flavonoids and diterpenoids from Dodonaea angustifolia JF - South African journal of botany : an international interdisciplinary journal for botanical sciences KW - Dodonaea angustifolia KW - Surface exudates KW - Flavone KW - Flavanone KW - Diterpenoid KW - Antimicrobial activities Y1 - 2014 U6 - https://doi.org/10.1016/j.sajb.2013.11.012 SN - 0254-6299 SN - 1727-9321 VL - 91 SP - 58 EP - 62 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Primus, Philipp-Alexander A1 - Ritschel, Thomas A1 - Sigueenza, Pilar Y. A1 - Cauqui, Miguel Angel A1 - Hernandez-Garrido, Juan Carlos A1 - Kumke, Michael Uwe T1 - High-resolution spectroscopy of europium-doped ceria as a tool to correlate structure and catalytic activity JF - The journal of physical chemistry : C, Nanomaterials and interfaces N2 - Site-selective emission spectra of Eu3+-doped CeO2 nanoparticles up to the D-5(0) - F-7(5) transition were recorded under cryogenic conditions to identify the local structure around the Eu3+ dopants in ceria. It is found that pretreatment conditions are crucial for the redistribution of dopants from a broad variety of environments to six well-defined lattice sites. The influence of the dopant and the host structure on the catalytic activity was investigated. A relationship between structure and reactivity is discussed. It is shown that oxygen transport is most efficient in particles with a pronounced amorphous character. Y1 - 2014 U6 - https://doi.org/10.1021/jp505467r SN - 1932-7447 VL - 118 IS - 40 SP - 23349 EP - 23360 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Salffner, Katharina A1 - Boehm, Michael A1 - Reich, Oliver A1 - Löhmannsröben, Hans-Gerd T1 - A broadband cavity ring-down spectrometer based on an incoherent near infrared light source JF - Applied physics : B, Lasers and optics Y1 - 2014 U6 - https://doi.org/10.1007/s00340-014-5762-9 SN - 0946-2171 SN - 1432-0649 VL - 116 IS - 4 SP - 785 EP - 792 PB - Springer CY - New York ER - TY - CHAP A1 - Arlt, Olga A1 - Schwiebs, Anja A1 - Pfarr, Kathrin A1 - Ranglack, Annika A1 - Bouzas, Ferreiros Nerea A1 - Schreiber, Yannick A1 - Neuber, Corinna A1 - Kleuser, Burkhard A1 - Pfeilschifter, Josef M. A1 - Radeke, Heinfried H. T1 - Dynamic interaction between sphingolipid enzymes, S1P and inflammatory cytokine regulation in dendritic cells T2 - NAUNYN-SCHMIEDEBERGS ARCHIVES OF PHARMACOLOGY Y1 - 2014 SN - 0028-1298 SN - 1432-1912 VL - 387 SP - S91 EP - S91 PB - Springer CY - New York ER - TY - JOUR A1 - Schulze, Nicole A1 - Appelhans, D. A1 - Tiersch, Brigitte A1 - Koetz, Joachim T1 - Morphological transformation of vesicles into tubular structures by adding polyampholytes or dendritic glycopolymers JF - Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects N2 - For the first time tubulating properties of spherical dendritic glycopolymers and linear alternating polyampholytes against non-uniform negatively charged giant vesicles are proven by light microscopy and cryo-scanning electron microscopy study. Real time observation of the morphological transformation from giant vesicles to tubular structures, simulating morphogenesis in living cells, is given by using the cationic and H-bond active dendritic glycopolymer accompanied by reducing the size of the giant vesicles and the evidence of vesicle-vesicle interaction which was only postulated in a previous study. Similar morphogenesis of non-uniform giant vesicles into tubular network structure can be observed by using a polyampholyte in the stretched conformation at pH 9. Pearl necklace and tubular network structure formation are also observed by applying anionic vesicles of significant smaller dimensions with average size dimensions of 35 nm, after adding the polyampholyte at pH 9. However, the fitting accuracy between the functional groups along the backbone chain of the polyampholyte on one side and the vesicle surface on the other side is of high importance for the transformation process by using polyampholytes. The resulting tubular and network structures offer new fields of application as microfluidic transport channels or template phases for the shape controlled formation of nanoparticles. (C) 2014 Elsevier B.V. All rights reserved. KW - Alternating polyampholytes KW - Maltose-modified PEI KW - Network structure KW - Template phase KW - Cryo-SEM KW - DLS Y1 - 2014 U6 - https://doi.org/10.1016/j.colsurfa.2014.06.007 SN - 0927-7757 SN - 1873-4359 VL - 457 SP - 326 EP - 332 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Schmidt, Bernd A1 - Elizarov, Nelli A1 - Berger, René A1 - Hölter, Frank T1 - Scope and limitations of the Heck-Matsuda-coupling of phenol diazonium salts and styrenes: a protecting-group economic synthesis of phenolic stilbenes N2 - 4-Phenol diazonium salts undergo Pd-catalyzed Heck reactions with various styrenes to 4ï-hydroxy stilbenes. In almost all cases higher yields and fewer side products were observed, compared to the analogous 4-methoxy benzene diazonium salts. In contrast, the reaction fails completely with 2- and 3-phenol diazonium salts. For these substitution patterns the methoxy-substituted derivatives are superior. Y1 - 2014 UR - http://pubs.rsc.org/en/content/articlepdf/2013/ob/c3ob40420j U6 - https://doi.org/10.1039/C3OB40420J SN - 1477-0520 ER - TY - JOUR A1 - Schönborn, Jan Boyke A1 - Hartke, Bernd T1 - Photochemical dynamics of Photochemical dynamics of E-methylfurylfulgide - Kinematic effects in photorelaxation dynamics of furylfulgides N2 - With the present theoretical study of the photochemical switching of E-methylfurylfulgide we contribute an important step towards the understanding of the photochemical processes in furylfulgide-related molecules. We have carried out large-scale, full-dimensional direct semiempirical configuration-interaction surface-hopping dynamics of the photoinduced ring-closure reaction. Simulated static and dynamical UV/Vis-spectra show good agreement with experimental data of the same molecule. By a careful investigation of our dynamical data, we were able to identify marked differences to the dynamics of the previously studied E-isopropylfurylfulgide. With our simulations we can not only reproduce the experimentally observed quantum yield differences qualitatively but we can also pinpoint two reasons for them: kinematics and pre-orientation. With our analysis, we thus offer straightforward molecular explanations for the high sensitivity of the photodynamics towards seemingly minor changes in molecular constitution. Beyond the realm of furylfulgides, these insights provide additional guidance to the rational design of photochemically switchable molecules. Y1 - 2014 UR - http://pubs.rsc.org/en/content/articlehtml/2014/cp/c3cp53495b U6 - https://doi.org/10.1039/C3CP53495B ER - TY - GEN A1 - Floss, Gereon T1 - Theoretische Untersuchungen zur lichtinduzierten Isomerisierung von gekoppelten Azobenzolderivaten Y1 - 2014 CY - Potsdam ER - TY - JOUR A1 - Schmidt, Bernd A1 - Hauke, Sylvia T1 - Cross metathesis of allyl alcohols: how to suppress and how to promote double bond isomerization N2 - Under standard conditions the cross metathesis of allyl alcohols and methyl acrylate is accompanied by the formation of ketones, resulting from uncontrolled and undesired double bond isomerization. By conducting the CM in the presence of phenol, the catalyst loading and the reaction time required for quantiative conversion can be reduced, and isomerization can be suppressed. On the other hand, consecutive isomerization can be deliberately promoted by evaporating excess methyl acrylate after completing cross metathesis and by adding a base or silane as chemical triggers. Y1 - 2014 UR - http://pubs.rsc.org/en/content/articlepdf/2013/ob/c3ob40167g U6 - https://doi.org/10.1039/c3ob40167g SN - 1477-0520 ER - TY - JOUR A1 - Kleinpeter, Erich A1 - Klaumuenzer, Ute T1 - Quantification of the push-pull Effect in disubstituted alkynes - Application of occupation quotients pi*/pi and C-13 chemical shift differences Delta delta(C C) JF - Journal of molecular structure N2 - Structures, C-13 chemical shifts, and the occupation quotients of anti-bonding pi* and bonding pi orbitals of the C C triple bond along a series of push-pull alkynes (p)X-C6H4 C(O)-C C-NH-C6H4-Y(P) (X,Y= H, Me, OMe, NMe2, NO2, COMe, COOMe, F, Cl, Br) were computed at the DFT level (B3LYP/6-311G**) of theory. Both the stereochemistry (cis/trans-isomers) by steric twist and the push-pull character by both C-13 chemical shift differences (Delta delta(C C)) and the occupation quotient (pi(C C)/pi(C C)) were studied; the latter two parameters can be readily employed to precisely quantify the push-pull effect in alkynes. (C) 2014 Elsevier B.V. All rights reserved. KW - Push-pull effect KW - C-13 chemical shift difference Delta delta(C C) KW - Occupation quotient pi*/pi KW - Push-pull alkynes KW - Steric hindrance Y1 - 2014 U6 - https://doi.org/10.1016/j.molstruc.2014.05.072 SN - 0022-2860 SN - 1872-8014 VL - 1074 SP - 193 EP - 195 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Magadula, Joseph J. A1 - Masimba, Pax J. A1 - Tarimo, Rose B. A1 - Msengwa, Zaituni A1 - Mbwambo, Zakariah H. A1 - Heydenreich, Matthias A1 - Breard, Dimitri A1 - Richomme, Pascal T1 - Mammea-type coumarins from Mammea usambarensis Verdc. JF - Biochemical systematics and ecology N2 - Phytochemical investigations of Mammea usambarensis resulted into the isolation a delta-tocotrienol (1) and five known mammea-type coumarins (2-6). Their structures were determined by NMR, IR, and LC-MS spectroscopic methods and by comparison of their spectral and physical data with those reported previously in the literature. The presence of these compounds is consistent with the compound classes reported from other members of the genus Mammal. Compound 6 is isolated from the Mammea genus for the first time. This is the new source of mammea-type coumarin compounds while the chemotaxonomic significance of this investigation is summarized. (C) 2014 Elsevier Ltd. All rights reserved. KW - Mammea usambarensis KW - Isolations KW - Mammea-type coumarins KW - Chemotaxonomy Y1 - 2014 U6 - https://doi.org/10.1016/j.bse.2014.05.004 SN - 0305-1978 SN - 1873-2925 VL - 56 SP - 65 EP - 67 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Bandrauk, Andre D. A1 - Paramonov, Guennaddi K. T1 - Excitation of muonic molecules dd mu and dt mu by super-intense attosecond soft X-ray laser pulses: Shaped post-laser-pulse muonic oscillations and enhancement of nuclear fusion JF - International journal of modern physics : E, Nuclear physics N2 - The quantum dynamics of muonic molecular ions dd mu and dt mu excited by linearly polarized along the molecular (z)-axis super-intense laser pulses is studied beyond the Born-Oppenheimer approximation by the numerical solution of the time-dependent Schrodinger equation within a three-dimensional model, including the internuclear distance R and muon coordinates z and rho. The peak-intensity of the super-intense laser pulses used in our simulations is I-0 = 3.51 x 10(22) W/cm(2) and the wavelength is lambda(l) = 5nm. In both dd mu and dt mu, expectation values < z > and of muon demonstrate "post-laser-pulse" oscillations after the ends of the laser pulses. In dd mu post-laser-pulse z-oscillations appear as shaped nonoverlapping "echo-pulses". In dt mu post-laser-pulse muonic z-oscillations appear as comparatively slow large-amplitude oscillations modulated with small-amplitude pulsations. The post-laser-pulse rho-oscillations in both dd mu and dt mu appear, for the most part, as overlapping "echo-pulses". The post-laser-pulse oscillations do not occur if the Born-Oppenheimer approximation is employed. Power spectra generated due to muonic motion along both optically active z and optically passive rho degrees of freedom are calculated. The fusion probability in dt mu can be increased by more than 11 times by making use of three sequential super-intense laser pulses. The energy released from the dt fusion in dt mu can by more than 20 GeV exceed the energy required to produce a usable muon and the energy of the laser pulses used to enhance the fusion. The possibility of power production from the laser-enhanced muon-catalyzed fusion is discussed. KW - Muonic molecules KW - super-intense laser pulses KW - laser-enhanced nuclear fusion Y1 - 2014 U6 - https://doi.org/10.1142/S0218301314300148 SN - 0218-3013 SN - 1793-6608 VL - 23 IS - 9 PB - World Scientific CY - Singapore ER - TY - JOUR A1 - Hasinovic, H. A1 - Friberg, S. E. A1 - Kovach, Ildyko A1 - Koetz, Joachim T1 - Destabilization of a dual emulsion to form a Janus emulsion JF - Colloid and polymer science : official journal of the Kolloid-Gesellschaft N2 - A vegetable oil (VO) was added to an emulsion of silicone oil in water (SO/W) with mixing limited to once turning the test tube upside down. Initially, the VO was dispersed into virtually centimeter-sized drops and the emulsion contained effectively no Janus drops, while after 1 h of agitation at a low level to prevent creaming, drops of 50-100-mu m size of the two oils were observed: in addition to an insignificant number of Janus drops. The topology of the latter showed them to emanate from flocculated individual drops of the two oils, but with no discernible effect by the interfacial tension equilibrium on the drop topology. Continued gentle mixing gave increasing fraction of Janus drops of increased size with a topology gradually approaching the one expected from the interfacial equilibrium at the contact line. The spontaneous formation of Janus drops indicated a reduction of the interfacial free energy in the process and the interfacial energy difference between separate and Janus drops was calculated for an appropriate range of interfacial tensions and for all oil fractions. The calculations enabled a distinction of the decrease due to interfacial area changes from the reduction of interfacial tensions per se, with the latter only a minor fraction. KW - Emulsion destabilization KW - Janus emulsions KW - Interfacial equilibrium KW - Microfluidics Y1 - 2014 U6 - https://doi.org/10.1007/s00396-014-3263-3 SN - 0303-402X SN - 1435-1536 VL - 292 IS - 9 SP - 2319 EP - 2324 PB - Springer CY - New York ER - TY - JOUR A1 - Plehn, Thomas A1 - Megow, Jörg A1 - May, Volkhard T1 - Concerted charge and energy transfer processes in a highly flexible fullerene-dye system: a mixed quantum-classical study JF - Physical chemistry, chemical physics : a journal of European Chemical Societies N2 - Photoinduced excitation energy transfer and accompanying charge separation are elucidated for a supramolecular system of a single fullerene covalently linked to six pyropheophorbide-a dye molecules. Molecular dynamics simulations are performed to gain an atomistic picture of the architecture and the surrounding solvent. Excitation energy transfer among the dye molecules and electron transfer from the excited dyes to the fullerene are described by a mixed quantum-classical version of the Forster rate and the semiclassical Marcus rate, respectively. The mean characteristic time of energy redistribution lies in the range of 10 ps, while electron transfer proceeds within 150 ps. In between, on a 20 to 50 ps time-scale, conformational changes take place in the system. This temporal hierarchy of processes guarantees efficient charge separation, if the structure is exposed to a solvent. The fast energy transfer can adopt the dye excitation to the actual conformation. In this sense, the probability to achieve charge separation is large enough since any dominance of unfavorable conformations that exhibit a large dye-fullerene distance is circumvented. And the slow electron transfer may realize an averaging with respect to different conformations. To confirm the reliability of our computations, ensemble measurements on the charge separation dynamics are simulated and a very good agreement with the experimental data is obtained. Y1 - 2014 U6 - https://doi.org/10.1039/c4cp01081g SN - 1463-9076 SN - 1463-9084 VL - 16 IS - 25 SP - 12949 EP - 12958 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Hass, Philipp A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Fully biodegradable modification of wood for improvement of dimensional stability and water absorption properties by poly(epsilon-caprolactone) grafting into the cell walls JF - Green chemistry : an international journal and green chemistry resource N2 - Materials derived from renewable resources are highly desirable in view of more sustainable manufacturing. Among the available natural materials, wood is one of the key candidates, because of its excellent mechanical properties. However, wood and wood-based materials in engineering applications suffer from various restraints, such as dimensional instability upon humidity changes. Several wood modification treatments increase water repellence, but the insertion of hydrophobic polymers can result in a composite material which cannot be considered as renewable anymore. In this study, we report on the grafting of the fully biodegradable poly(epsilon-caprolactone) (PCL) inside the wood cell walls by Sn(Oct)(2) catalysed ring-opening polymerization (ROP). The presence of polyester chains within the wood cell wall structure is monitored by confocal Raman imaging and spectroscopy as well as scanning electron microscopy. Physical tests reveal that the modified wood is more hydrophobic due to the bulking of the cell wall structure with the polyester chains, which results in a novel fully biodegradable wood material with improved dimensional stability. Y1 - 2014 U6 - https://doi.org/10.1039/c4gc00194j SN - 1463-9262 SN - 1463-9270 VL - 16 IS - 6 SP - 3313 EP - 3321 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Sarauli, David A1 - Xu, Chenggang A1 - Dietzel, Birgit A1 - Schulz, Burkhard A1 - Lisdat, Fred T1 - A multilayered sulfonated polyaniline network with entrapped pyrroloquinoline quinone-dependent glucose dehydrogenase: tunable direct bioelectrocatalysis JF - Journal of materials chemistry : B, Materials for biology and medicine N2 - A feasible approach to construct multilayer films of sulfonated polyanilines - PMSA1 and PABMSA1 containing different ratios of aniline, 2-methoxyaniline-5-sulfonic acid (MAS) and 3-aminobenzoic acid (AB), with the entrapped redox enzyme pyrroloquinoline quinone-dependent glucose dehydrogenase (PQQ-GDH) on Au and ITO electrode surfaces, is described. The formation of layers has been followed and confirmed by electrochemical impedance spectroscopy (EIS), which demonstrates that the multilayer assembly can be achieved in a progressive and uniform manner. The gold and ITO electrodes subsequently modified with PMSA1:PQQ-GDH and PABMSA1 films are studied by cyclic voltammetry (CV) and UV-Vis spectroscopy which show a significant direct bioelectrocatalytical response to the oxidation of the substrate glucose without any additional mediator. This response correlates linearly with the number of deposited layers. Furthermore, the constructed polymer/enzyme multilayer system exhibits a rather good long-term stability, since the catalytic current response is maintained for more than 60% of the initial value even after two weeks of storage. This verifies that a productive interaction of the enzyme embedded in the film of substituted polyaniline can be used as a basis for the construction of bioelectronic units, which are useful as indicators for processes liberating glucose and allowing optical and electrochemical transduction. Y1 - 2014 U6 - https://doi.org/10.1039/c4tb00336e SN - 2050-750X SN - 2050-7518 VL - 2 IS - 21 SP - 3196 EP - 3203 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Sangoro, Joshia R. A1 - Iacob, C. A1 - Agapov, A. L. A1 - Wang, Yangyang A1 - Berdzinski, Stefan A1 - Rexhausen, Hans A1 - Strehmel, Veronika A1 - Friedrich, C. A1 - Sokolov, A. P. A1 - Kremer, F. T1 - Decoupling of ionic conductivity from structural dynamics in polymerized ionic liquids JF - Soft matter N2 - Charge transport and structural dynamics in low molecular weight and polymerized 1-vinyl-3-pentylimidazolium bis(trifluoromethylsulfonyl) imide ionic liquids (ILs) are investigated by a combination of broadband dielectric spectroscopy, dynamic mechanical spectroscopy and differential scanning calorimetry. While the dc conductivity and fluidity exhibit practically identical temperature dependence for the non-polymerized IL, a significant decoupling of ionic conduction from structural dynamics is observed for the polymerized IL. In addition, the dc conductivity of the polymerized IL exceeds that of its molecular counterpart by four orders of magnitude at their respective calorimetric glass transition temperatures. This is attributed to the unusually high mobility of the anions especially at lower temperatures when the structural dynamics is significantly slowed down. A simple physical explanation of the possible origin of the remarkable decoupling of ionic conductivity from structural dynamics is proposed. Y1 - 2014 U6 - https://doi.org/10.1039/c3sm53202j SN - 1744-683X SN - 1744-6848 VL - 10 IS - 20 SP - 3536 EP - 3540 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Cywinski, Piotr J. A1 - Nono, Katia Nchimi A1 - Charbonniere, Loic J. A1 - Hammann, Tommy A1 - Löhmannsröben, Hans-Gerd T1 - Photophysical evaluation of a new functional terbium complex in FRET-based time-resolved homogenous fluoroassays JF - Physical chemistry, chemical physics : a journal of European Chemical Societies N2 - A new functional luminescent lanthanide complex (LLC) has been synthesized with terbium as a central lanthanide ion and biotin as a functional moiety. Unlike in typical lanthanide complexes assembled via carboxylic moieties, in the presented complex, four phosphate groups are chelating the central lanthanide ion. This special chemical assembly enhances the complex stability in phosphate buffers conventionally used in biochemistry. The complex synthesis strategy and photophysical properties are described as well as the performance in time-resolved Forster Resonance Energy Transfer (FRET) assays. In those assays, this biotin-LLC transferred energy either to acceptor organic dyes (Cy5 or AF680) labelled on streptavidin or to quantum dots (QD655 or QD705) surfacefunctionalised with streptavidins. The permanent spatial donor-acceptor proximity is assured through strong and stable biotin-streptavidin binding. The energy transfer is evidenced from the quenching observed in donor emission and from a decrease in donor luminescence decay, both associated with simultaneous increase in acceptor intensity and in the decay time. The dye-based assays are realised in TRIS and in PBS, whereas QD-based systems are studied in borate buffer. The delayed emission analysis allows for quantifying the recognition process and for auto-fluorescence-free detection, which is particularly relevant for application in bioanalysis. In accordance with Forster theory, Forsterradii (R0) were found to be around 60 angstrom for organic dyes and around 105 angstrom for QDs. The FRET efficiency (Z) reached 80% and 25% for dye and QD acceptors, respectively. Physical donor-acceptor distances (r) have been determined in the range 45-60 angstrom for organic dye acceptors, while for acceptor QDs between 120 angstrom and 145 angstrom. This newly synthesised biotin-LLC extends the class of highly sensitive analytical tools to be applied in the bioanalytical methods such as time-resolved fluoroimmunoassays (TR-FIA), luminescent imaging and biosensing. Y1 - 2014 U6 - https://doi.org/10.1039/c3cp54883j SN - 1463-9076 SN - 1463-9084 VL - 16 IS - 13 SP - 6060 EP - 6067 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Bauer, Maximilian A1 - Godec, Aljaz A1 - Metzler, Ralf T1 - Diffusion of finite-size particles in two-dimensional channels with random wall configurations JF - Physical chemistry, chemical physics : a journal of European Chemical Societies N2 - Diffusion of chemicals or tracer molecules through complex systems containing irregularly shaped channels is important in many applications. Most theoretical studies based on the famed Fick-Jacobs equation focus on the idealised case of infinitely small particles and reflecting boundaries. In this study we use numerical simulations to consider the transport of finite-size particles through asymmetrical two-dimensional channels. Additionally, we examine transient binding of the molecules to the channel walls by applying sticky boundary conditions. We consider an ensemble of particles diffusing in independent channels, which are characterised by common structural parameters. We compare our results for the long-time effective diffusion coefficient with a recent theoretical formula obtained by Dagdug and Pineda Y1 - 2014 U6 - https://doi.org/10.1039/c3cp55160a SN - 1463-9076 SN - 1463-9084 VL - 16 IS - 13 SP - 6118 EP - 6128 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Fudickar, Werner A1 - Linker, Torsten T1 - Intermediates in the formation and thermolysis of peroxides from oxidations with singlet oxygen JF - Australian journal of chemistry N2 - Herein we describe the recent mechanistic understandings of the singlet oxygen ene reaction to give hydroperoxides and the [4+2] cycloaddition affording endoperoxides. Both experimental findings and theoretical work conclude in the formation of intermediates structurally similar to perepoxides during the ene reaction. Such intermediates mainly control the regio- and stereoselectivities of this reaction class. For the [4+2] cycloaddition, both a synchronous concerted reaction (benzene, naphthalenes) and a stepwise reaction with a non-symmetric zwitterionic intermediate (larger acenes) have been found. The thermolysis of endoperoxides derived from acenes proceeds stepwise for anthracenes, but in a concerted manner for less stable adducts such as naphthalene. Y1 - 2014 U6 - https://doi.org/10.1071/CH13423 SN - 0004-9425 SN - 1445-0038 VL - 67 IS - 3 SP - 320 EP - 327 PB - CSIRO CY - Clayton ER - TY - JOUR A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Gierlinger, Notburga A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Improvement of wood material properties via in situ polymerization of styrene into tosylated cell walls JF - RSC Advances N2 - As an engineering material derived from renewable resources, wood possesses excellent mechanical properties in view of its light weight but also has some disadvantages such as low dimensional stability upon moisture changes and low durability against biological attack. Polymerization of hydrophobic monomers in the cell wall is one of the potential approaches to improve the dimensional stability of wood. A major challenge is to insert hydrophobic monomers into the hydrophilic environment of the cell walls, without increasing the bulk density of the material due to lumen filling. Here, we report on an innovative and simple method to insert styrene monomers into tosylated cell walls (i.e. -OH groups from natural wood polymers are reacted with tosyl chloride) and carry out free radical polymerization under relatively mild conditions, generating low wood weight gains. In-depth SEM and confocal Raman microscopy analysis are applied to reveal the distribution of the polystyrene in the cell walls and the lumen. The embedding of polystyrene in wood results in reduced water uptake by the wood cell walls, a significant increase in dimensional stability, as well as slightly improved mechanical properties measured by nanoindentation. Y1 - 2014 U6 - https://doi.org/10.1039/c4ra00741g SN - 2046-2069 VL - 4 IS - 25 SP - 12981 EP - 12988 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Jeon, Jae-Hyung A1 - Chechkin, Aleksei V. A1 - Metzler, Ralf T1 - Scaled Brownian motion: a paradoxical process with a time dependent diffusivity for the description of anomalous diffusion JF - Physical chemistry, chemical physics : a journal of European Chemical Societies N2 - Anomalous diffusion is frequently described by scaled Brownian motion (SBM), a Gaussian process with a power-law time dependent diffusion coefficient. Its mean squared displacement is < x(2)(t) similar or equal to 2K(t)t with K(t) similar or equal to t(alpha-1) for 0 < alpha < 2. SBM may provide a seemingly adequate description in the case of unbounded diffusion, for which its probability density function coincides with that of fractional Brownian motion. Here we show that free SBM is weakly non-ergodic but does not exhibit a significant amplitude scatter of the time averaged mean squared displacement. More severely, we demonstrate that under confinement, the dynamics encoded by SBM is fundamentally different from both fractional Brownian motion and continuous time random walks. SBM is highly non-stationary and cannot provide a physical description for particles in a thermalised stationary system. Our findings have direct impact on the modelling of single particle tracking experiments, in particular, under confinement inside cellular compartments or when optical tweezers tracking methods are used. Y1 - 2014 U6 - https://doi.org/10.1039/c4cp02019g SN - 1463-9076 SN - 1463-9084 VL - 16 IS - 30 SP - 15811 EP - 15817 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Hildebrand, Viet A1 - Laschewsky, André A1 - Zehm, Daniel T1 - On the hydrophilicity of polyzwitterion poly (N, N-dimethyl-N(3-(methacrylamido)propyl)ammoniopropane sulfonate) in water, deuterated water, and aqueous salt solutions JF - Journal of biomaterials science : Polymer edition KW - polyzwitterion KW - sulfobetaine KW - synthesis KW - fluorescence label KW - upper critical solution temperature KW - isotope effect KW - anti-polyelectrolyte effect Y1 - 2014 U6 - https://doi.org/10.1080/09205063.2014.939918 SN - 0920-5063 SN - 1568-5624 VL - 25 IS - 14-15 SP - 1602 EP - 1618 PB - Routledge, Taylor & Francis Group CY - Abingdon ER - TY - JOUR A1 - Zborowski, Krzysztof Kazimierz A1 - Koch, Andreas A1 - Kleinpeter, Erich A1 - Proniewicz, Leonard Marian T1 - Searching for aromatic celate rings. Oxygen versus Thio and Seleno Ligands JF - Zeitschrift für physikalische Chemie : international journal of research in physical chemistry and chemical physics N2 - As a part of searching for fully aromatic chelate compounds, copper complexes of malondialdehyde as well as its sulfur and selenium derivatives were investigated using the DFT quantum chemical methods. Chelate complexes of both Cu(I) and Cu(II) ions wereconsidered. Aromaticity of the metal complexes studied were analyzed using NICS(0), NICS(1), PDI, I-ring, MCI, ICMCI and I-B aromaticity indices, and by TSNMRS visualizations of the spatial magnetic properties. It seems that partial aromaticityof studied chelates increases when oxygen atoms in malondialdehyde are replaced by sulfur and selenium. KW - Aromaticity KW - Chelatoaromaticity KW - Copper Metal Complexes KW - Quantum Chemical Calculations Y1 - 2014 U6 - https://doi.org/10.1515/zpch-2014-0528 SN - 0942-9352 VL - 228 IS - 8 SP - 869 EP - 878 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Wessig, Pablo A1 - Gerngross, Maik A1 - Pape, Simon A1 - Bruhns, Philipp A1 - Weber, Jens T1 - Novel porous materials based on oligospiroketals (OSK) JF - RSC Advances N2 - New porous materials based on covalently connected monomers are presented. The key step of the synthesis is an acetalisation reaction. In previous years we used acetalisation reactions extensively to build up various molecular rods. Based on this approach, investigations towards porous polymeric materials were conducted by us. Here we wish to present the results of these studies in the synthesis of 1D polyacetals and porous 3D polyacetals. By scrambling experiments with 1D acetals we could prove that exchange reactions occur between different building blocks (evidenced by MALDI-TOF mass spectrometry). Based on these results we synthesized porous 3D polyacetals under the same mild conditions. Y1 - 2014 U6 - https://doi.org/10.1039/c4ra04437a SN - 2046-2069 VL - 4 IS - 59 SP - 31123 EP - 31129 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Grunzel, Petra A1 - Pilarek, Maciej A1 - Steinbrueck, Doerte A1 - Neubauer, Antje A1 - Brand, Eva A1 - Kumke, Michael Uwe A1 - Neubauer, Peter A1 - Krause, Mirja T1 - Mini-scale cultivation method enables expeditious plasmid production in Escherichia coli JF - Biotechnology journal : systems & synthetic biology, nanobiotech, medicine N2 - The standard procedure in the lab for plasmid isolation usually involves a 2-mL, 16 h over-night cultivation in 15-mL bioreaction tubes in LB medium. This is time consuming, and not suitable for high-throughput applications. This study shows that it is possible to produce plasmid DNA (pDNA) in a 1.5-mL microcentrifuge tube with only 100 L cultivation volume in less than 7 h with a simple protocol. Compared with the standard LB cultivation for pDNA production reaching a final pDNA concentration range of 1.5-4 mu g mL(-1), a 6- to 10-fold increase in plasmid concentration (from 10 up to 25 mu g mL(-1) cultivation volume) is achieved using an optimized medium with an internal substrate delivery system (EnBase (R)). Different strains, plasmids, and the applicability of different inoculation tools (i.e. different starting ODs) were compared, demonstrating the robustness of the system. Additionally, dissolved oxygen was monitored in real time online, indicating that under optimized conditions oxygen limitation can be avoided. We developed a simple protocol with a significantly decreased procedure time, enabling simultaneous handling of more samples, while a consistent quality and a higher final pDNA concentration are ensured. KW - Escherichia coli KW - High-cell-density culture KW - Miniaturized cultivations KW - Optical oxygen sensor KW - Plasmid DNA production Y1 - 2014 U6 - https://doi.org/10.1002/biot.201300177 SN - 1860-6768 SN - 1860-7314 VL - 9 IS - 1 SP - 128 EP - 136 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Vaskova, Zuzana A1 - Kitanovski, Nives A1 - Jaglicic, Zvonko A1 - Strauch, Peter A1 - Ruzickova, Zdenka A1 - Valigura, Dusan A1 - Koman, Marian A1 - Kozlevcar, Bojan A1 - Moncol, Jan T1 - Synthesis and magneto-structural characterization of copper(II) nitrobenzoate complexes containing nicotinamide or methylnicotinamide ligands JF - Polyhedron : the international journal of inorganic and organometallic chemistry N2 - Three new copper(II) 4-nitrobenzoato coordination compounds (4-NO(2)bz(-) = 4-nitrobenzoate anions) with N-methylnicotinamide (mna) [Cu(4-NO(2)bz)(2)(mna)(2)(H2O)] (1), [Cu(4-NO(2)bz)(2)(mu-mna)(H2O)](2) (2) and [Cu(mu-4-NO(2)bz)(2)(mna)](2) (3) were synthesized and characterized. Due to a comparison, additional two related compounds [Cu(3,5-(NO2)(2)bz)(2)(mna)(2)(H2O)] (4) (nia = nicotinamide, 3,5-(NO2)(2)bz(-) = 3,5-dinitrobenzoate anions) and [Cu(mu-2-NO(2)bz)(2)(mna)](2) (5) (2-NO(2)bz(-) = 2-nitrobenzoate anions) were isolated. The mononuclear compounds with mna 1 and nia 4 show CuO2N2O chromophores with the water molecule placed at the apex of the square pyramid. The square-pyramidal coordination sphere CuO3NO in 2 differs to CuO2N2O in 1 and 4. Differently, the water molecule is in 2 at the basal-plane, while two mna molecules serve also as bridges via N-py and 0-amido enabling a dinuclear molecular structure 1, 2 and 4 are paramagnetic though a dinuclear structure is seen in 2, while a clear-cut strong antiferromagnetic (AFM) coupling (2J -300 cm(-1)) is found for the compounds 3 and 5. (C) 2014 Elsevier Ltd. All rights reserved. KW - Copper(II) KW - Nicotinamide KW - N-methylnicotinamide KW - Crystal structure KW - Magnetic properties Y1 - 2014 U6 - https://doi.org/10.1016/j.poly.2014.07.017 SN - 0277-5387 VL - 81 SP - 555 EP - 563 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Pereira, Fernanda S. A1 - Nascimento, Heliara D. L. A1 - Magalhaes, Alvicler A1 - Peter, Martin G. A1 - Bataglion, Giovana Anceski A1 - Eberlin, Marcos N. A1 - Gonzalez, Eduardo R. P. T1 - ESI(+)-MS and GC-MS study of the hydrolysis of N-azobenzyl derivatives of chitosan JF - Molecules N2 - New N-p-chloro-, N-p-bromo-, and N-p-nitrophenylazobenzylchitosan derivatives, as well as the corresponding azophenyl and azophenyl-p-sulfonic acids, were synthesized by coupling N-benzylvchitosan with aryl diazonium salts. The synthesized molecules were analyzed by UV-Vis, FT-IR, H-1-NMR and N-15-NMR spectroscopy. The capacity of copper chelation by these materials was studied by AAS. Chitosan and the derivatives were subjected to hydrolysis and the products were analyzed by ESI(+)-MS and GC-MS, confirming the formation of N-benzyl chitosan. Furthermore, the MS results indicate that a nucleophilic aromatic substitution (SnAr) reaction occurs under hydrolysis conditions, yielding chloroaniline from N-p-bromo-, and N-p-nitrophenylazo-benzylchitosan as well as bromoaniline from N-p-chloro-, and N-p-nitrophenylazobenzyl-chitosan. KW - chitosan KW - N-azobenzylchitosan KW - ESI-MS KW - GC-MS KW - SnAr reaction Y1 - 2014 U6 - https://doi.org/10.3390/molecules191117604 SN - 1420-3049 VL - 19 IS - 11 SP - 17604 EP - 17618 PB - MDPI CY - Basel ER - TY - JOUR A1 - Körzdörfer, Thomas A1 - Bredas, Jean-Luc T1 - Organic electronic materials: recent advances in the DFT description of the ground and excited states using tuned range-separated hybrid functionals JF - Accounts of chemical research N2 - CONSPECTUS: Density functional theory (DFT) and its time-dependent extension (TD-DFT) are powerful tools enabling the theoretical prediction of the ground- and excited-state properties of organic electronic materials with reasonable accuracy at affordable computational costs. Due to their excellent accuracy-to-numerical-costs ratio, semilocal and global hybrid functionals such as B3LYP have become the workhorse for geometry optimizations and the prediction of vibrational spectra in modern theoretical organic chemistry. Despite the overwhelming success of these out-of-the-box functionals for such applications, the computational treatment of electronic and structural properties that are of particular interest in organic electronic materials sometimes reveals severe and qualitative failures of such functionals. Important examples include the overestimation of conjugation, torsional barriers, and electronic coupling as well as the underestimation of bond-length alternations or excited-state energies in low-band-gap polymers. In this Account, we highlight how these failures can be traced back to the delocalization error inherent to semilocal and global hybrid functionals, which leads to the spurious delocalization of electron densities and an overestimation of conjugation. The delocalization error for systems and functionals of interest can be quantified by allowing for fractional occupation of the highest occupied molecular orbital. It can be minimized by using long-range corrected hybrid functionals and a nonempirical tuning procedure for the range-separation parameter. We then review the benefits and drawbacks of using tuned long-range corrected hybrid functionals for the description of the ground and excited states of pi-conjugated systems. In particular, we show that this approach provides for robust and efficient means of characterizing the electronic couplings in organic mixed-valence systems, for the calculation of accurate torsional barriers at the polymer limit, and for the reliable prediction of the optical absorption spectrum of low-band-gap polymers. We also explain why the use of standard, out-of-the-box range-separation parameters is not recommended for the DFT and/or TD-DFT description of the ground and excited states of extended, pi-conjugated systems. Finally, we highlight a severe drawback of tuned range-separated hybrid functionals by discussing the example of the calculation of bond-length alternation in polyacetylene, which leads us to point out the challenges for future developments in this field. Y1 - 2014 U6 - https://doi.org/10.1021/ar500021t SN - 0001-4842 SN - 1520-4898 VL - 47 IS - 11 SP - 3284 EP - 3291 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Cywinski, Piotr J. A1 - Hammann, Tommy A1 - Huehn, Dominik A1 - Parak, Wolfgang J. A1 - Hildebrandt, Niko A1 - Löhmannsröben, Hans-Gerd T1 - Europium-quantum dot nanobioconjugates as luminescent probes for time-gated biosensing JF - Journal of biomedical optics N2 - Nanobioconjugates have been synthesized using cadmium selenide quantum dots (QDs), europium complexes (EuCs), and biotin. In those conjugates, long-lived photoluminescence (PL) is provided by the europium complexes, which efficiently transfer energy via Forster resonance energy transfer (FRET) to the QDs in close spatial proximity. As a result, the conjugates have a PL emission spectrum characteristic for QDs combined with the long PL decay time characteristic for EuCs. The nanobioconjugates synthesis strategy and photo-physical properties are described as well as their performance in a time-resolved streptavidin-biotin PL assay. In order to prepare the QD-EuC-biotin conjugates, first an amphiphilic polymer has been functionalized with the EuC and biotin. Then, the polymer has been brought onto the surface of the QDs (either QD655 or QD705) to provide functionality and to make the QDs water dispersible. Due to a short distance between EuC and QD, an efficient FRET can be observed. Additionally, the QD-EuC-biotin conjugates' functionality has been demonstrated in a PL assay yielding good signal discrimination, both from autofluorescence and directly excited QDs. These newly designed QD-EuC-biotin conjugates expand the class of highly sensitive tools for bioanalytical optical detection methods for diagnostic and imaging applications. (C) 2014 Society of Photo-Optical Instrumentation Engineers (SPIE) KW - quantum dots KW - europium complex KW - amphiphilic polymer assembly KW - nanobioconjugate KW - biosensor KW - time-resolved fluorescence Y1 - 2014 U6 - https://doi.org/10.1117/1.JBO.19.10.101506 SN - 1083-3668 SN - 1560-2281 VL - 19 IS - 10 PB - SPIE CY - Bellingham ER - TY - JOUR A1 - Sarauli, David A1 - Peters, Kristina A1 - Xu, Chenggang A1 - Schulz, Burkhard A1 - Fattakhova-Rohlfing, Dina A1 - Lisdat, Fred T1 - 3D-Electrode architectures for enhanced direct bioelectrocatalysis of pyrroloquinoline quinone-dependent glucose dehydrogenase JF - ACS applied materials & interfaces N2 - We report on the fabrication of a complex electrode architecture for efficient direct bioelectrocatalysis. In the developed procedure, the redox enzyme pyrroloquinoline quinone-dependent glucose dehydrogenase entrapped in a sulfonated polyaniline [poly(2-methoxyaniline-5-sulfonic acid)-co-aniline] was immobilized on macroporous indium tin oxide (macroITO) electrodes. The use of the 3D-conducting scaffold with a large surface area in combination with the conductive polymer enables immobilization of large amounts of enzyme and its efficient communication with the electrode, leading to enhanced direct bioelectrocatalysis. In the presence of glucose, the fabricated bioelectrodes show an exceptionally high direct bioelectrocatalytical response without any additional mediator. The catalytic current is increased more than 200-fold compared to planar ITO electrodes. Together with a high long-term stability (the current response is maintained for >90% of the initial value even after 2 weeks of storage), the transparent 3D macroITO structure with a conductive polymer represents a valuable basis for the construction of highly efficient bioelectronic units, which are useful as indicators for processes liberating glucose and allowing optical and electrochemical transduction. KW - 3D electrode structures KW - macroITO KW - conductive polymer KW - PQQ-GDH KW - direct bioelectrocatalysis KW - bioelectrochemistry Y1 - 2014 U6 - https://doi.org/10.1021/am5046026 SN - 1944-8244 VL - 6 IS - 20 SP - 17887 EP - 17893 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Goetze, Jan P. A1 - Kröner, Dominik A1 - Banerjee, Shiladitya A1 - Karasulu, Bora A1 - Thiel, Walter T1 - Carotenoids as a shortcut for chlorophyll Soret-to-Q band energy flow JF - ChemPhysChem : a European journal of chemical physics and physical chemistry N2 - It is proposed that xanthophylls, and carotenoids in general, may assist in energy transfer from the chlorophyll Soret band to the Q band. Ground-state (1A(g)) and excited-state (1B(u)) optimizations of violaxanthin (Vx) and zeaxanthin (Zx) are performed in an environment mimicking the light-harvesting complex II (LHCII), including the closest chlorophyll b molecule (Chl). Time-dependent density functional theory (TD-DFT, CAM-B3LYP functional) is used in combination with a semi-empirical description to obtain the excited-state geometries, supported by additional DFT/multireference configuration interaction calculations, with and without point charges representing LHCII. In the ground state, Vx and Zx show similar properties. At the 1B(u) minimum, the energy of the Zx 1Bu state is below the Chl Q band, in contrast to Vx. Both Vx and Zx may act as acceptors of Soret-state energy; transfer to the Q band seems to be favored for Vx. These findings suggest that carotenoids may generally mediate Soret-to-Q energy flow in LHCII. KW - carotenoids KW - chlorophyll KW - density functional calculations KW - energy transfer KW - xanthophylls Y1 - 2014 U6 - https://doi.org/10.1002/cphc.201402233 SN - 1439-4235 SN - 1439-7641 VL - 15 IS - 15 SP - 3391 EP - 3400 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Comminges, Clement A1 - Frasca, Stefano A1 - Suetterlin, Martin A1 - Wischerhoff, Erik A1 - Laschewsky, André A1 - Wollenberger, Ursula T1 - Surface modification with thermoresponsive polymer brushes for a switchable electrochemical sensor JF - RSC Advances N2 - Elaboration of switchable surfaces represents an interesting way for the development of a new generation of electrochemical sensors. In this paper, a method for growing thermoresponsive polymer brushes from a gold surface pre-modified with polyethyleneimine (PEI), subsequent layer-by-layer polyelectrolyte assembly and adsorption of a charged macroinitiator is described. We propose an easy method for monitoring the coil-to-globule phase transition of the polymer brush using an electrochemical quartz crystal microbalance with dissipation (E-QCM-D). The surface of these polymer modified electrodes shows reversible switching from the swollen to the collapsed state with temperature. As demonstrated from E-QCM-D measurements using an original signal processing method, the switch is operating in three reversible steps related to different interfacial viscosities. Moreover, it is shown that the one electron oxidation of ferrocene carboxylic acid is dramatically affected by the change from the swollen to the collapsed state of the polymer brush, showing a spectacular 86% decrease of the charge transfer resistance between the two states. Y1 - 2014 U6 - https://doi.org/10.1039/c4ra07190e SN - 2046-2069 VL - 4 IS - 81 SP - 43092 EP - 43097 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Braune, Steffen A1 - Walter, M. A1 - Schulze, F. A1 - Lendlein, Andreas A1 - Jung, Friedrich T1 - Changes in platelet morphology and function during 24 hours of storage JF - Clinical hemorheology and microcirculation : blood flow and vessels N2 - For in vitro studies assessing the interaction of platelets with implant materials, common and standardized protocols for the preparation of platelet rich plasma (PRP) are lacking, which may lead to non-matching results due to the diversity of applied protocols. Particularly, the aging of platelets during prolonged preparation and storage times is discussed to lead to an underestimation of the material thrombogenicity. Here, we study the influence of whole blood-and PRP-storage times on changes in platelet morphology and function. Whole blood PFA100 closure times increased after stimulation with collagen/ADP and collagen/epinephrine. Twenty four hours after blood collection, both parameters were prolonged pathologically above the upper limit of the reference range. Numbers of circulating platelets, measured in PRP, decreased after four hours, but no longer after twenty four hours. Mean platelet volumes (MPV) and platelet large cell ratios (P-LCR, 12 fL - 40 fL) decreased over time. Immediately after blood collection, no debris or platelet aggregates could be visualized microscopically. After four hours, first debris and very small aggregates occurred. After 24 hours, platelet aggregates and also debris progressively increased. In accordance to this, the CASY system revealed an increase of platelet aggregates (up to 90 mu m diameter)with increasing storage time. The percentage of CD62P positive platelets and PF4 increased significantly with storage time in resting PRP. When soluble ADP was added to stored PRP samples, the number of activatable platelets decreased significantly over storage time. The present study reveals the importance of a consequent standardization in the preparation of WB and PRP. Platelet morphology and function, particularly platelet reactivity to adherent or soluble agonists in their surrounding milieu, changed rapidly outside the vascular system. This knowledge is of crucial interest, particularly in the field of biomaterial development for cardiovascular applications, and may help to define common standards in the in vitro hemocompatibility testing of biomaterials. KW - Platelet KW - platelet function KW - platelet rich plasma KW - whole blood KW - platelet aging KW - platelet storage KW - hemocompatibility KW - biomaterials Y1 - 2014 U6 - https://doi.org/10.3233/CH-141876 SN - 1386-0291 SN - 1875-8622 VL - 58 IS - 1 SP - 159 EP - 170 PB - IOS Press CY - Amsterdam ER - TY - JOUR A1 - Kovach, Ildyko A1 - Koetz, Joachim A1 - Friberg, Stig E. T1 - Janus emulsions stabilized by phospholipids JF - Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects N2 - Janus emulsions were formed by mixing three immiscible liquids; this implies two oil components (i.e. olive oil (00) and silicone oil (SiO)) with water in presence of interfacial active components. The morphology and size of Janus droplets formed strongly depended on the type of surfactant used. In presence of a non-ionic surfactant, i.e. Tween 80, large engulfed Janus droplets were formed. By adding phospholipids to the system the droplet size was decreased and more stable Janus droplets formed. Interfacial tension measurements carried out using a spinning drop apparatus and a ring tensiometer demonstrate that interfacial tension is the most important factor controlling the size, morphology and stability of Janus droplets. When the interfacial tension between oil and water becomes <= 1 mN/m, smaller Janus droplets are formed. Such conditions are fulfilled when phospholipids are used in combination with non-ionic surfactant Tween 80. The morphology of the double droplets is predominantly controlled by the viscosity and interfacial tension between the two oil phases. By using different types of phospholipids, i.e. asolectin and lecithin instead of a more concentrated phosphatidylcholine (phospholipon), the interfacial tension is decreased and different morphologies of engulfing can be observed. KW - Janus emulsions KW - Spinning drop KW - Interfacial tension KW - Phospholipids Y1 - 2014 U6 - https://doi.org/10.1016/j.colsurfa.2013.08.065 SN - 0927-7757 SN - 1873-4359 VL - 441 SP - 66 EP - 71 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kroener, Dominik A1 - Schimka, Selina A1 - Klamroth, Tillmann T1 - Laser control for coupled torsions in chiroptical switches: a combined quantum and classical dynamics approach JF - The journal of physical chemistry : C, Nanomaterials and interfaces N2 - We present a novel laser pulse control for the chiroptical switch 1-(2-cis-fluoroethenyl)-2-fluoro-3,5-dibromobenzene mounted on adamantane, where the latter imitates a linker group or part of a solid surface. This molecular device offers three switching states: a true achiral "off"-state and two chiral "on"-states of opposite handedness. Due to the alignment of its chiral axis along the surface normal several defined orientations of the switch have to be considered for an efficient stereocontrol strategy. In addition to these different initial conditions, coupled torsional degrees of freedom around the chiral axis make the quest for highly stereoselective laser pulses a challenge. The necessary flexibility in pulse accomplished by employing the iterative stochastic pulse optimization method we presented recently. Still, the complexity of the system dictates a combined treatment by fast molecular dynamics and computationally intensive quantum dynamics. Although quantum effects are found to be of importance, the pulses optimized within the classical treatment allow us to turn on the chirality of the switch, achieving high enantioselectivity in the quantum treatment for all orientations at the same time. Y1 - 2014 U6 - https://doi.org/10.1021/jp410342a SN - 1932-7447 VL - 118 IS - 2 SP - 1322 EP - 1331 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Metzler, Ralf A1 - Jeon, Jae-Hyung A1 - Cherstvy, Andrey G. A1 - Barkai, Eli T1 - Anomalous diffusion models and their properties: non-stationarity, non-ergodicity, and ageing at the centenary of single particle tracking JF - Physical chemistry, chemical physics : a journal of European Chemical Societies N2 - Modern microscopic techniques following the stochastic motion of labelled tracer particles have uncovered significant deviations from the laws of Brownian motion in a variety of animate and inanimate systems. Such anomalous diffusion can have different physical origins, which can be identified from careful data analysis. In particular, single particle tracking provides the entire trajectory of the traced particle, which allows one to evaluate different observables to quantify the dynamics of the system under observation. We here provide an extensive overview over different popular anomalous diffusion models and their properties. We pay special attention to their ergodic properties, highlighting the fact that in several of these models the long time averaged mean squared displacement shows a distinct disparity to the regular, ensemble averaged mean squared displacement. In these cases, data obtained from time averages cannot be interpreted by the standard theoretical results for the ensemble averages. Here we therefore provide a comparison of the main properties of the time averaged mean squared displacement and its statistical behaviour in terms of the scatter of the amplitudes between the time averages obtained from different trajectories. We especially demonstrate how anomalous dynamics may be identified for systems, which, on first sight, appear to be Brownian. Moreover, we discuss the ergodicity breaking parameters for the different anomalous stochastic processes and showcase the physical origins for the various behaviours. This Perspective is intended as a guidebook for both experimentalists and theorists working on systems, which exhibit anomalous diffusion. Y1 - 2014 U6 - https://doi.org/10.1039/c4cp03465a SN - 1463-9076 SN - 1463-9084 VL - 16 IS - 44 SP - 24128 EP - 24164 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Kopec, Maciej A1 - Niemiec, Wiktor A1 - Laschewsky, André A1 - Nowakowska, Maria A1 - Zapotoczny, Szczepan T1 - Photoinduced energy and electron transfer in micellar multilayer films JF - The journal of physical chemistry : C, Nanomaterials and interfaces N2 - Micellar multilayer films were prepared from an amphiphilic comb-like polycation ("polysoap") and the polyanion poly(styrene sulfonate) (PSS) using alternate polyelectrolyte layer-by-layer (LbL) self-assembly. Linear growth of the film thickness was evidenced by UV-vis spectroscopy and spectroscopic ellipsometry. Imaging by atomic force microscopy (AFM) indicated that the micellar conformation adopted by the polycation in solutions was preserved in the films. Thus, hydrophobic photoactive molecules, which were solubilized by the hydrophobic nanodomains of the micellar polymer prior to deposition, could be transferred into the films. Photoinduced energy transfer was observed in the nanostructured multilayers between naphthalene (donor) and perylene (acceptor) molecules embedded inside the polymer micelles. The efficiency of the energy transfer process can be controlled to some extent by introducing spacer layers between the layers containing the donor or acceptor, revealing partial stratification of the micellar LbL films. Also, photoinduced electron transfer was evidenced between perylene (donor) and butyl viologen (acceptor) molecules embedded inside the multilayers by steady-state fluorescence spectroscopy. The obtained photoactive nanostructures are promising candidates for solar-to-chemical energy conversion systems. Y1 - 2014 U6 - https://doi.org/10.1021/jp410808z SN - 1932-7447 VL - 118 IS - 4 SP - 2215 EP - 2221 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Kosmella, Sabine A1 - Venus, Jane A1 - Hahn, Jennifer A1 - Prietzel, Claudia Christina A1 - Koetz, Joachim T1 - Low-temperature synthesis of polyethyleneimine-entrapped CdS quantum dots JF - Chemical physics letters N2 - This Letter is focused on the one-pot formation of CdS nanoparticles in aqueous medium in presence of polyethyleneimine (PEI). Quantum dots can be obtained by adding a pre-cooled aqueous Na2S solution to a pre-cooled aqueous CdCl2 solution dropwise in presence of PEI. Field flow fractionation in combination with TEM experiments show a time dependent agglomeration of individual quantum dots from 1.6 nm up to 3.2 nm in size. The hyperbranched PEI of moderate molar mass (>20000 g/mol) is an excellent polymer to prevent a further increase of the particle size. Therefore, stable fluorescent PEI-capped CdS quantum dots are available. Y1 - 2014 U6 - https://doi.org/10.1016/j.cplett.2013.12.019 SN - 0009-2614 SN - 1873-4448 VL - 592 SP - 114 EP - 119 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kleinpeter, Erich ED - Webb, GA T1 - Quantification and visualization of the anisotropy effect in NMR spectroscopy by through-space NMR shieldings JF - Annual reports on NMR spectroscopy JF - Annual Reports on NMR Spectroscopy N2 - The anisotropy effect of functional groups (respectively the ring-current effect of aryl moieties) in H-1 NMR spectra has been computed as spatial NICS (through-space NMR chemical shieldings) and visualized by iso-chemical-shielding surfaces of various size and low(high) field direction. Hereby, the anisotropy/ring-current effect, which proves to be the molecular response property of spatial NICS, can be quantified and can be readily employed for assignment purposes in proton NMR spectroscopy-characteristic examples of stereochemistry and position assignments (the latter in supramolecular structures) will be given. In addition, anisotropy/ring-current effects in H-1 NMR spectra can be quantitatively separated from the second dominant structural effect in proton NMR spectra, the steric compression effect, pointing into the reverse direction, and the ring-current effect, by far the strongest anisotropy effect, can be impressively employed to visualize and quantify (anti) aromaticity and to clear up standing physical-organic phenomena as are pseudo-, spherical, captodative, homo-and chelatoaromaticity, to characterize the pi-electronic structure of, for example, fulvenes, fulvalenes, annulenes or fullerenes and to differentiate aromatic and quinonoid structures. KW - Through-space NMR shielding (TSNMRS) KW - Anisotropy effect KW - Stereochemistry KW - Ring-current effect KW - Aromatic or quinonoid KW - Aromaticity KW - Chelatoaromaticity KW - Binding pocket position KW - Supramolecular compounds KW - Diastereomers assignment Y1 - 2014 SN - 978-0-12-800184-4 U6 - https://doi.org/10.1016/B978-0-12-800184-4.00003-5 SN - 0066-4103 VL - 82 SP - 115 EP - 166 PB - Elsevier CY - San Diego ER - TY - JOUR A1 - Degtyar, Elena A1 - Harrington, Matthew J. A1 - Politi, Yael A1 - Fratzl, Peter T1 - The mechanical role of metal ions in biogenic protein-based materials JF - Angewandte Chemie : a journal of the Gesellschaft Deutscher Chemiker ; International edition N2 - Protein-metal interactions-traditionally regarded for roles in metabolic processes-are now known to enhance the performance of certain biogenic materials, influencing properties such as hardness, toughness, adhesion, and self-healing. Design principles elucidated through thorough study of such materials are yielding vital insights for the design of biomimetic metallopolymers with industrial and biomedical applications. Recent advances in the understanding of the biological structure-function relationships are highlighted here with a specific focus on materials such as arthropod biting parts, mussel byssal threads, and sandcastle worm cement. KW - adhesives KW - biomaterials KW - metal coordination KW - sacrificial bonds KW - self-healing materials Y1 - 2014 U6 - https://doi.org/10.1002/anie.201404272 SN - 1433-7851 SN - 1521-3773 VL - 53 IS - 45 SP - 12026 EP - 12044 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Schmidt, Bernd A1 - Riemer, Martin A1 - Schilde, Uwe T1 - Chroman-4-ones via microwave-promoted domino claisen rearrangement-oxa-michael addition: Synthesis of tabchromones A and B JF - Synlett : accounts and rapid communications in synthetic organic chemistry N2 - Allyl phenyl ethers with a pendant enone substituent undergo, upon microwave irradiation, a domino sequence of Claisen rearrangement and 6-endo-trig-cyclization to furnish functionalized chroman-4-ones. The natural products tabchromones A and B were synthesized via this method. KW - cyclization KW - Michael addition KW - rearrangement KW - tandem reaction KW - Wacker reaction Y1 - 2014 U6 - https://doi.org/10.1055/s-0034-1379364 SN - 0936-5214 SN - 1437-2096 VL - 25 IS - 20 SP - 2943 EP - 2946 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Moskalik, Mikhail Yu. A1 - Astakhova, Vera V. A1 - Schilde, Uwe A1 - Sterkhova, Irina V. A1 - Shainyan, Bagrat A. T1 - Assembling of 3,6-diazabicyclo[3.1.0]hexane framework in oxidative triflamidation of substituted buta-1,3-dienes JF - Tetrahedron KW - Trifluoromethanesulfonamide KW - Arenesulfonamides KW - Cycloaddition KW - 1,3-Dienes KW - 3,6-Diazabicyclo[3.1.0]hexanes KW - X-ray Y1 - 2014 U6 - https://doi.org/10.1016/j.tet.2014.09.050 SN - 0040-4020 VL - 70 IS - 45 SP - 8636 EP - 8641 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Schöne, Anne-Christin A1 - Schulz, Burkhard A1 - Richau, Klaus A1 - Kratz, Karl A1 - Lendlein, Andreas T1 - Characterization of Langmuir films prepared from copolyesterurethanes based on oligo(omega-pentadecalactone) and oligo(epsilon-caprolactone)segments JF - Macromolecular chemistry and physics N2 - A series of multiblock copolymers (PDLCL) synthesized from oligo(omega-pentadecalactone) diol (OPDL) and oligo(epsilon-caprolactone) diol (OCL), which are linked by 2,2(4), 4-trimethyl-hexamethylene diisocyanate (TMDI), is investigated by the Langmuir monolayer technique at the air-water interface. Brewster angle microscopy (BAM) and spectroscopic ellipsometry are employed to characterize the polymer film morphologies in situ. PDLCL containing >= 40 wt% OCL segments form homogeneous Langmuir monofilms after spreading. The film elasticity modulus decreases with increasing amounts of OPDL segments in the copolymer. In contrast, the OCL-free polyesterurethane OPDL-TMDI cannot be spread to monomolecular films on the water surface properly, and movable slabs are observed by BAM even at low surface pressures. The results of the in situ morphological characterization clearly show that essential information concerning the reliability of Langmuir monolayer degradation (LMD) experiments cannot be obtained from the evaluation of the pi-A isotherms only. Consequently, in situ morphological characterization turns out to be indispensable for characterization of Langmuir layers before LMD experiments. KW - brewster angle microscopy KW - ellipsometry KW - Langmuir layers KW - morphology KW - polyesterurethanes Y1 - 2014 U6 - https://doi.org/10.1002/macp.201400377 SN - 1022-1352 SN - 1521-3935 VL - 215 IS - 24 SP - 2437 EP - 2445 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tsendra, Oksana A1 - Scott, Andrea Michalkova A1 - Gorb, Leonid A1 - Boese, Adrian Daniel A1 - Hill, Frances C. A1 - Ilchenko, Mykola M. A1 - Leszczynska, Danuta A1 - Leszczynski, Jerzy T1 - Adsorption of Nitrogen-Containing Compounds on the (100) alpha-Quartz Surface: Ab Initio Cluster Approach JF - The journal of physical chemistry : C, Nanomaterials and interfaces N2 - A cluster approach extended to the ONIOM methodology has been applied using several density functionals and Moller-Plesset perturbation theory (MP2) to simulate the adsorption of selected nitrogen-containing compounds [NCCs, 2,4,6-trinitrotoluene (TNT), 2,4-dinitrotoluene (DNT), 2,4-dinitroanisole (DNAN), and 3-nitro-1,2,4-triazole-5-one (NTO)] on the hydroxyated (100) surface of a-quartz. The structural properties were calculated using the M06-2X functional and 6-31G(d,p) basis set. The M06-2X-D3, PBE-D3, and MP2 methods were used to calculate the adsorption energies. Results have been compared with the data from other studies of adsorption of compounds of similar nature on silica. Effect of deformation of the silica surface and adsorbates on the binding energy values was also studied. The atoms in molecules (AIM) analysis was employed to characterize the adsorbate-adsorbent binding and to calculate the bond energies. The silica surface shows different sorption affinity toward the chemicals considered depending on their electronic structure. All target NCCs are physisorbed on the modeled silica surface. Adsorption occurs due to the formation of multiple hydrogen bonds between the functional groups of NCCs and surface silanol groups. Parallel orientation of NCCs interacting with the silica surface was found to be favorable when compared with perpendicularly oriented NCCs. NTO was found to be the most strongly adsorbed on the silica surface among all of the considered compounds. Dispersion correction was shown to play an important role in the DFT calculations of the adsorption energies of silica-NCC systems. Y1 - 2014 U6 - https://doi.org/10.1021/jp406827h SN - 1932-7447 VL - 118 IS - 6 SP - 3023 EP - 3034 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Sutton, Christopher A1 - Körzdörfer, Thomas A1 - Gray, Matthew T. A1 - Brunsfeld, Max A1 - Parrish, Robert M. A1 - Sherrill, C. David A1 - Sears, John S. A1 - Bredas, Jean-Luc T1 - Accurate description of torsion potentials in conjugated polymers using density functionals with reduced self-interaction error JF - The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr N2 - We investigate the torsion potentials in two prototypical pi-conjugated polymers, polyacetylene and polydiacetylene, as a function of chain length using different flavors of density functional theory. Our study provides a quantitative analysis of the delocalization error in standard semilocal and hybrid density functionals and demonstrates how it can influence structural and thermodynamic properties. The delocalization error is quantified by evaluating the many-electron self-interaction error (MESIE) for fractional electron numbers, which allows us to establish a direct connection between the MESIE and the error in the torsion barriers. The use of non-empirically tuned long-range corrected hybrid functionals results in a very significant reduction of the MESIE and leads to an improved description of torsion barrier heights. In addition, we demonstrate how our analysis allows the determination of the effective conjugation length in polyacetylene and polydiacetylene chains. Y1 - 2014 U6 - https://doi.org/10.1063/1.4863218 SN - 0021-9606 SN - 1089-7690 VL - 140 IS - 5 PB - American Institute of Physics CY - Melville ER - TY - JOUR A1 - Cywinski, Piotr J. A1 - Moro, Artur J. A1 - Löhmannsröben, Hans-Gerd T1 - Cyclic GMP recognition using ratiometric QD-fluorophore conjugate nanosensors JF - Biosensors and bioelectronics : the principal international journal devoted to research, design development and application of biosensors and bioelectronics KW - Quantum dots KW - Naphthyridines KW - Cyclic GMP KW - Base pairing KW - Fluorescent nanoconjugate KW - Nanosensor Y1 - 2014 U6 - https://doi.org/10.1016/j.bios.2013.09.002 SN - 0956-5663 SN - 1873-4235 VL - 52 SP - 288 EP - 292 PB - Elsevier CY - Oxford ER - TY - GEN A1 - Boese, Adrian Daniel T1 - Assessment of coupled cluster theory and more approximate methods for Hydrogen Bonded Systems (vol 9, pg 4403, 2013) T2 - Journal of chemical theory and computation Y1 - 2014 U6 - https://doi.org/10.1021/ct500041j SN - 1549-9618 SN - 1549-9626 VL - 10 IS - 2 SP - 893 EP - 893 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Schirmack, Janosch A1 - Boehm, Michael A1 - Brauer, Chris A1 - Löhmannsröben, Hans-Gerd A1 - de Vera, Jean-Pierre Paul A1 - Moehlmann, Diedrich A1 - Wagner, Dirk T1 - Laser spectroscopic real time measurements of methanogenic activity under simulated Martian subsurface analog conditions JF - Planetary and space science N2 - On Earth, chemolithoautothrophic and anaerobic microorganisms such as methanogenic archaea are regarded as model organisms for possible subsurface life on Mars. For this reason, the methanogenic strain Methanosarcina soligelidi (formerly called Methanosarcina spec. SMA-21), isolated from permafrost-affected soil in northeast Siberia, has been tested under Martian thermo-physical conditions. In previous studies under simulated Martian conditions, high survival rates of these microorganisms were observed. In our study we present a method to measure methane production as a first attempt to study metabolic activity of methanogenic archaea during simulated conditions approaching conditions of Mars-like environments. To determine methanogenic activity, a measurement technique which is capable to measure the produced methane concentration with high precision and with high temporal resolution is needed. Although there are several methods to detect methane, only a few fulfill all the needed requirements to work within simulated extraterrestrial environments. We have chosen laser spectroscopy, which is a non-destructive technique that measures the methane concentration without sample taking and also can be run continuously. In our simulation, we detected methane production at temperatures down to -5 degrees C, which would be found on Mars either temporarily in the shallow subsurface or continually in the deep subsurface. The pressure of 50 kPa which we used in our experiments, corresponds to the expected pressure in the Martian near subsurface. Our new device proved to be fully functional and the results indicate that the possible existence of methanogenic archaea in Martian subsurface habitats cannot be ruled out. (C) 2013 Published by Elsevier Ltd. KW - Mars KW - Methanogens KW - Methane KW - Sub-zero temperature (Celsius) KW - Wavelength modulation spectroscopy (laser spectroscopy) Y1 - 2014 U6 - https://doi.org/10.1016/j.pss.2013.08.019 SN - 0032-0633 VL - 98 SP - 198 EP - 204 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Yu, Mingfeng A1 - Ast, Sandra A1 - Yu, Qun A1 - Lo, Anthony T. S. A1 - Flehr, Roman A1 - Todd, Matthew H. A1 - Rutledge, Peter J. T1 - Incorporating a piperidinyl group in the fluorophore extends the fluorescence lifetime of click-derived cyclam-naphthalimide conjugates JF - PLoS one N2 - Ligands incorporating a tetraazamacrocycle receptor, a 'click'-derived triazole and a 1,8-naphthalimide fluorophore have proven utility as probes for metal ions. Three new cyclam-based molecular probes are reported, in which a piperidinyl group has been introduced at the 4-position of the naphthalimide fluorophore. These compounds have been synthesized using the copper(I)-catalyzed azide-alkyne Huisgen cycloaddition and their photophysical properties studied in detail. The alkylamino group induces the expected red-shift in absorption and emission spectra relative to the simple naphthalimide derivatives and gives rise to extended fluorescence lifetimes in aqueous buffer. The photophysical properties of these systems are shown to be highly solvent-dependent. Screening the fluorescence responses of the new conjugates to a wide variety of metal ions reveals significant and selective fluorescence quenching in the presence of copper(II), yet no fluorescence enhancement with zinc(II) as observed previously for the simple naphthalimide derivatives. Reasons for this different behaviour are proposed. Cytotoxicity testing shows that these new cyclam-triazole-dye conjugates display little or no toxicity against either DLD-1 colon carcinoma cells or MDA-MB-231 breast carcinoma cells, suggesting a potential role for these and related systems in biological sensing applications. Y1 - 2014 U6 - https://doi.org/10.1371/journal.pone.0100761 SN - 1932-6203 VL - 9 IS - 7 PB - PLoS CY - San Fransisco ER - TY - JOUR A1 - Shainyan, Bagrat A. A1 - Kleinpeter, Erich T1 - Conformational flexibility of 4,4-dimethyl-3,4-dihydro-2H-1,4-thiasiline and its monoheterocyclic analogs JF - Russian journal of general chemistry N2 - Conformational behavior of the first cyclic organosilicon vinylsulfide, 4,4-dimethyl-3,4-dihydro-2H-1,4-thiasiline as well as its monoheterocyclic analogs, 3,4-dihydro-2H-pyran, 3,4-dihydro-2H-thiopyran, and 1,1-dimethyl-1,2,3,4-tetrahydrosiline is studied in comparison with the carbocyclic analog, cyclohexene, using the methods of low-temperature NMR spectroscopy and theoretical calculations at the DFT and MP2 levels of theory. The barrier to the ring inversion with respect to that in cycloxene is increased in 3,4-dihydro-2H-pyran and 1,1-dimethyl-1,2,3,4-tetrahydrosiline, but, in contrast to the suggestions made in the literature, is decreased in 3,4-dihydro-2H-thiopyran. In 4,4-dimethyl-3,4-dihydro-2H-1,4-thiasiline the barrier is intermediate between those in the corresponding monoheterocycles, 1,1-dimethyl-1,2,3,4-tetrahydrosiline and 3,4-dihydro-2H-thiopyran. The observed variations are rationalized from the viewpoint of the interaction of the pi-electrons of the C=C double bond with the orbitals of heteroatoms in the ring. The structure of the transition state for the ring inversion is discussed. KW - 4,4-dimethyl-3,4-dihydro-2H-1,4-thiasiline KW - 1,1-dimethyl-1,2,3,4-tetrahydrosiline KW - 3,4-dihydro-2H-thiopyran KW - 3,4-dihydro-2H-pyran KW - onformational analysis Y1 - 2014 U6 - https://doi.org/10.1134/S1070363214070135 SN - 1070-3632 SN - 1608-3350 VL - 84 IS - 7 SP - 1325 EP - 1329 PB - Pleiades Publ. CY - New York ER - TY - JOUR A1 - Ortmann, Thomas A1 - Ahrens, Heiko A1 - Milewski, Sven A1 - Lawrenz, Frank A1 - Groening, Andreas A1 - Laschewsky, André A1 - Garnier, Sebastien A1 - Helm, Christiane A. T1 - Lipid monolayers with adsorbed oppositely charged polyelectrolytes: Influence of reduced charge densities JF - Polymers N2 - Polyelectrolytes in dilute solutions (0.01 mmol/L) adsorb in a two-dimensional lamellar phase to oppositely charged lipid monolayers at the air/water interface. The interchain separation is monitored by Grazing Incidence X-ray Diffraction. On monolayer compression, the interchain separation decreases to a factor of two. To investigate the influence of the electrostatic interaction, either the line charge density of the polymer is reduced (a statistic copolymer with 90% and 50% charged monomers) or mixtures between charged and uncharged lipids are used (dipalmitoylphosphatidylcholine (DPPC)/dioctadecyldimethylammonium bromide (DODAB)) On decrease of the surface charge density, the interchain separation increases, while on decrease of the linear charge density, the interchain separation decreases. The ratio between charged monomers and charged lipid molecules is fairly constant; it decreases up to 30% when the lipids are in the fluid phase. With decreasing surface charge or linear charge density, the correlation length of the lamellar order decreases. KW - lipid monolayer KW - polyelectrolyte adsorption KW - statistical copolymer KW - two-dimensional phases KW - surface charge KW - nematic phase KW - grazing incidence X-ray diffraction Y1 - 2014 U6 - https://doi.org/10.3390/polym6071999 SN - 2073-4360 VL - 6 IS - 7 SP - 1999 EP - 2017 PB - MDPI CY - Basel ER - TY - JOUR A1 - Marom, Noa A1 - Körzdörfer, Thomas A1 - Ren, Xinguo A1 - Tkatchenko, Alexandre A1 - Chelikowsky, James R. T1 - Size effects in the interface level alignment of dye-Sensitized TiO2 clusters JF - The journal of physical chemistry letters N2 - The efficiency of dye-sensitized solar cells (DSCs) depends critically on the electronic structure of the interfaces in the active region. We employ recently developed dispersion-inclusive density functional theory (DFT) and GW methods to study the electronic structure of TiO2 clusters sensitized with catechol molecules. We show that the energy level alignment at the dye-TiO2 interface is the result of an intricate interplay of quantum size effects and dynamic screening effects and that it may be manipulated by nanostructuring and functionalizing the TiO2. We demonstrate that the energy difference between the catechol LUMO and the TiO2 LUMO, which is associated with the injection loss in DSCs, may be reduced significantly by reducing the dimensions of nanostructured TiO2 and by functionalizing the TiO2 with wide-gap moieties, which contribute additional screening but do not interact strongly with the frontier orbitals of the TiO2 and the dye. Precise control of the electronic structure may be achieved via "interface engineering" in functional nanostructures. Y1 - 2014 U6 - https://doi.org/10.1021/jz5008356 SN - 1948-7185 VL - 5 IS - 14 SP - 2395 EP - 2401 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Brennecke, Johannes A1 - Ochs, Christopher J. A1 - Boudhar, Aicha A1 - Reux, Bastien A1 - Subramanian, Gomathy Sandhya A1 - Lear, Martin J. A1 - Trau, Dieter A1 - Hobley, Jonathan T1 - Design, preparation and assessment of surface-immobilised tetraphenylethenes for biosensing applications JF - Applied surface science : a journal devoted to applied physics and chemistry of surfaces and interfaces N2 - Tetraphenylethene (TPE) shows a significant increase of fluorescence intensity when the rotational freedom of its phenyl groups is restricted. This special property allows the use of TPE in sensor applications, which have been previously described for the liquid phase only. However, some applications utilising arrays require the immobilisation of TPE dyes on solid surfaces. In this work, we synthesised and investigated the fluorescence behaviour of TPE derivatives on silica particles and quartz slides and suggest ways to employ the dye's properties in solid phase biosensor applications. 2014 Published by Elsevier B.V. KW - Tetraphenylethene Bioassay Fluorescent dye KW - Microparticles Reagentless assay Y1 - 2014 U6 - https://doi.org/10.1016/j.apsusc.2014.04.061 SN - 0169-4332 SN - 1873-5584 VL - 307 SP - 475 EP - 481 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Shainyan, Bagrat A. A1 - Moskalik, Mikhail Yu A1 - Astakhova, Vera V. A1 - Schilde, Uwe T1 - Novel design of 3,8-diazabicyclo[3.2.1]octane framework in oxidative sulfonamidation of 1,5-hexadiene JF - Tetrahedron N2 - 1,5-Hexadiene reacts with trifluoromethanesulfonamide in the oxidative system (t-BuOCl+Nal) to give trans-2,5-bis(iodomethyl)-1-(trifluoromethylsulfonyl)pyrrolidine 5 and 3,8-bis(trifluoromethylsulfonyl)-3,8-diazabicyclo[3.2.1]octane 6. With arenesulfonamides ArSO2NH2 (Ar=Ph, Tol), the reaction stops at the formation of the trans and cis isomers of 2,5-bis(iodomethyl)-1-(arenesulfonyl)pyrrolidine 7 and 8 (1:1). The cis isomers of 7 and 8 do not undergo cyclization to the corresponding 3,8-disubstituted 3,8-diazabicyclo[3.2.1]octanes. The reaction with triflamide represents the first example of one-pot two-step route to 3,8-diazabicyclo[3.2.1]octane system. (C) 2014 Elsevier Ltd. All rights reserved. KW - Trifluoromethanesulfonamide KW - Arenesulfonamides KW - 1,5-Dienes KW - Cycloaddition KW - 3,8-Diazabicyclo[3.2.1]octane KW - X-ray Y1 - 2014 U6 - https://doi.org/10.1016/j.tet.2014.04.095 SN - 0040-4020 VL - 70 IS - 30 SP - 4547 EP - 4551 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Omorogie, Martins O. A1 - Babalola, Jonathan Oyebamiji A1 - Unuabonah, Emmanuel I. A1 - Gong, Jian R. T1 - Hybrid materials from agro-waste and nanoparticles: implications on the kinetics of the adsorption of inorganic pollutants JF - Environmental technology N2 - This study is a first-hand report of the immobilization of Nauclea diderrichii seed waste biomass (ND) (an agro-waste) with eco-friendly mesoporous silica (MS) and graphene oxide-MS (GO+MS ) nanoparticles, producing two new hybrid materials namely: MND adsorbent for agro-waste modified with MS and GND adsorbent for agro-waste modified with GO+MS nanoparticles showed improved surface area, pore size and pore volume over those of the agro-waste. The abstractive potential of the new hybrid materials was explored for uptake of Cr(III) and Pb(II) ions. Analysis of experimental data from these new hybrid materials showed increased initial sorption rate of Cr(III) and Pb(II) ions uptake. The amounts of Cr(III) and Pb(II) ions adsorbed by MND and GND adsorbents were greater than those of ND. Modification of N. diderrichii seed waste significantly improved its rate of adsorption and diffusion coefficient for Cr(III) and Pb(II) more than its adsorption capacity. The rate of adsorption of the heavy metal ions was higher with GO+MS nanoparticles than for other adsorbents. Kinetic data were found to fit well the pseudo-second-order and the diffusion-chemisorption kinetic models suggesting that the adsorption of Cr(III) and Pb(II) onto these adsorbents is mainly through chemisorption mechanism. Analysis of kinetic data with the homogeneous particle diffusion kinetic model suggests that particle diffusion (diffusion of ions through the adsorbent) is the rate-limiting step for the adsorption process. KW - adsorption KW - graphene oxide KW - nanoparticles KW - kinetic models KW - hybrid materials Y1 - 2014 U6 - https://doi.org/10.1080/09593330.2013.839747 SN - 0959-3330 SN - 1479-487X VL - 35 IS - 5 SP - 611 EP - 619 PB - Routledge, Taylor & Francis Group CY - Abingdon ER - TY - JOUR A1 - Schmidt, Bernd A1 - Hauke, Sylvia T1 - Metathesis-Based de novo synthesis of noviose JF - European journal of organic chemistry N2 - The rare carbohydrate L-(+)-noviose was synthesized from enantiomerically pure L-lactate. The configuration at C-4 was established by diastereoselective nucleophilic addition to an in-situ-generated lactaldehyde. The resulting homoallylic alcohol was further transformed into a set of ring-closing metathesis (RCM) precursors. These compounds were converted into noviose in few steps using RCM and RCM-allylic-oxidation sequences. KW - Carbohydrates KW - Allylic oxidation KW - Oxygen heterocycles KW - Metathesis KW - Ruthenium Y1 - 2014 U6 - https://doi.org/10.1002/ejoc.201301615 SN - 1434-193X SN - 1099-0690 VL - 2014 IS - 9 SP - 1951 EP - 1960 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Strehmel, Veronika A1 - Berdzinski, Stefan A1 - Strauch, Peter A1 - Hoffmann-Jacobsen, Kerstin A1 - Strehmel, Bernd T1 - Investigation of molecular solvents and ionic liquids with a dual probe JF - Zeitschrift für physikalische Chemie : international journal of research in physical chemistry and chemical physics N2 - A dual probe was investigated by UV-Vis, fluorescence, and ESR spectroscopy. It comprises the pyrene chromophore and the paramagnetic 2,2,6,6-tetramethylpiperidinyl-N-oxyl radical that are covalently linked together via an ester bridge. The dual probe was used to investigate molecular solvents of different polarity as well as ionic liquids bearing either imidazolium or pyrrolidinium cations and various anions, such as bis(trifluoromethylsulfonyl)imide, tetrafluoroborate, tris(pentafluoroethyl)trifluorophosphate, or dicyanamide. The dual probe does not show solvatochromism that is typical for some pyrenes. Furthermore, the dual probe is considerable less mobile compared to 2,2,6,6-tetramethylpiperidinyl-N-oxyl (TEMPO) without additional substituent as detected by ESR spectroscopy. This is caused by the bulky pyrenyl substituent bound at the dual probe resulting in a reduced mobility of the dual probe. KW - Ionic Liquid KW - Fluorescence KW - ESR KW - Molecular Probe Y1 - 2014 U6 - https://doi.org/10.1515/zpch-2014-0453 SN - 0942-9352 VL - 228 IS - 2-3 SP - 155 EP - 169 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Hartmann, Heike A1 - Lewerenz, Susann T1 - Campaigning against Apartheid in East and West Germany JF - Radical history review Y1 - 2014 U6 - https://doi.org/10.1215/01636545-2402068 SN - 0163-6545 IS - 119 SP - 191 EP - 204 PB - Duke Univ. Press CY - Durham ER - TY - JOUR A1 - Schmidt, Bernd A1 - Hauke, Sylvia A1 - Muehlenberg, Nino T1 - Imino glycals via Ruthenium-catalyzed RCM and isomerization JF - Synthesis N2 - N-Allyl-N-homoallylamines were converted in one step into cyclic enamides via a ruthenium-catalyzed assisted tandem catalytic ring-closing metathesis-isomerization sequence. The sequence relies on the in situ transformation of a metathesis active Ru-carbene into an isomerization active Ru-hydride by addition of hydroxide as a chemical trigger. KW - heterocycles KW - isomerization KW - metathesis KW - ruthenium KW - tandem reaction Y1 - 2014 U6 - https://doi.org/10.1055/s-0033-1338615 SN - 0039-7881 SN - 1437-210X VL - 46 IS - 12 SP - 1648 EP - 1658 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Schmidt, Bernd A1 - Hauke, Sylvia T1 - Olefin cross metathesis based de novo synthesis of a partially protected L-amicetose and a fully protected L-cinerulose derivative JF - Beilstein journal of organic chemistry N2 - Cross metathesis of a lactate derived allylic alcohol and acrolein is the entry point to a de novo synthesis of 4-benzoate protected L-amicetose and a cinerulose derivative protected at C5 and C1. KW - carbohydrates KW - de novo synthesis KW - lactate KW - metathesis KW - ruthenium Y1 - 2014 U6 - https://doi.org/10.3762/bjoc.10.102 SN - 1860-5397 VL - 10 SP - 1023 EP - 1031 PB - Beilstein-Institut zur Förderung der Chemischen Wissenschaften CY - Frankfurt, Main ER - TY - JOUR A1 - Hasinovic, Hida A1 - Boggs, Cami A1 - Friberg, Stig E. A1 - Kovach, Ildiko A1 - Koetz, Joachim T1 - Janus emulsions from a one-step process; optical microscopy images JF - Journal of dispersion science and technology N2 - The optical microscopy images of an emulsion are commonly distorted when viewed between a cover glass and a planar microscopy slide. An alternative method is to place the sample on a slide with a cavity, which in turn suffers from incomplete information for high internal phase ratio (HIPR) emulsions, due to the inevitable crowding of the drops. This problem is particularly acute for more complex emulsions, such as those with Janus drops, for which a detailed image of the drop is essential. A number of publications have recently described Janus emulsions prepared by a one-step high energy emulsification process with microscopy images obtained by the sample between a planar slide and a cover glass. The correlation to the morphology of emulsions in bulk of these images is critical, but, so far, a potential equivalence has not been established. Since the images are central in order to understand why Janus emulsions should form under such conditions, the need to ascertain any such association is urgent. With this contribution, we compare images from different microscopy methods to those of gently diluted HIPR emulsions. The results reveal that the images of the emulsion samples between a cover glass and a planar microscope slide actually present a realistic representation of the drop topology in bulk emulsions. KW - Janus drops KW - Emulsification KW - microemulsions KW - emulsion microscopy Y1 - 2014 U6 - https://doi.org/10.1080/01932691.2013.801019 SN - 0193-2691 SN - 1532-2351 VL - 35 IS - 5 SP - 613 EP - 618 PB - Taylor & Francis Group CY - Philadelphia ER - TY - JOUR A1 - Stumpe, Joachim A1 - Sakhno, O. A1 - Gritsai, Y. A1 - Rosenhauer, R. A1 - Fischer, Th. A1 - Rutloh, Michael A1 - Schaal, F. A1 - Weidenfeld, S. A1 - Jetter, M. A1 - Michler, P. A1 - Pruss, C. A1 - Osten, W. T1 - Active and passive LC based polarization elements JF - Molecular crystals and liquid crystals N2 - Passive and active polarization elements were created by surface and bulk photo-alignment of LCs, reactive LCs, photo-sensitive LCP and photo-curable monomer/LC composites. The use of different photo-sensitive liquid crystalline materials for the development of highly anisotropic elements with high spatial resolution and stability or, alternatively, fast switch ability will be discussed. Photo-active and voltage tunable polarization and diffraction elements are presented. For active micro-optic application a photo-addressed patterned retarder was created. Electrically switchable diffraction gratings were generated by interference exposure of photo-curable LC composites at room temperature characterized by droplet free morphology. These polarization sensitive diffraction elements are characterized be excellent optical properties and low switching times. KW - electrically switchable gratings. KW - diffractive elements KW - polymer/LC composites KW - switchable retarder KW - polarization gratings KW - Polarization elements Y1 - 2014 U6 - https://doi.org/10.1080/15421406.2014.917503 SN - 1542-1406 SN - 1563-5287 VL - 594 IS - 1 SP - 140 EP - 149 PB - Routledge, Taylor & Francis Group CY - Abingdon ER - TY - JOUR A1 - Schmidt, Bernd A1 - Riemer, Martin T1 - Suzuki-Miyaura coupling of halophenols and phenol boronic acids: systematic investigation of positional isomer effects and conclusions for the synthesis of phytoalexins from Pyrinae JF - The journal of organic chemistry N2 - The Suzuki-Miyaura couplings of o-, m-, and p-halophenols with o-, m-, and p-phenol boronic acids were investigated for all combinations under standardized conditions, using Pd/C as a heterogeneous catalyst and water as a solvent. In the case of iodophenols, conventional heating was used, while for bromophenols significantly better results could be obtained using microwave irradiation. This systematic study revealed that 2,4'-biphenol is particularly difficult to access, irrespective of the starting materials used, but that these difficulties can be overcome by using different additives. The conclusions drawn from this investigation allowed us to identify conditions for the protecting group-free or minimized total synthesis of biaryl-type phytoalexins. These compounds possess antibacterial activity and are produced by fruit trees as a response to microbial infection. Y1 - 2014 U6 - https://doi.org/10.1021/jo500675a SN - 0022-3263 VL - 79 IS - 9 SP - 4104 EP - 4118 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Victora, Andrea A1 - Moeller, Heiko M. A1 - Exner, Thomas E. T1 - Accurate ab initio prediction of NMR chemical shifts of nucleic acids and nucleic acids/protein complexes JF - Nucleic acids research N2 - NMR chemical shift predictions based on empirical methods are nowadays indispensable tools during resonance assignment and 3D structure calculation of proteins. However, owing to the very limited statistical data basis, such methods are still in their infancy in the field of nucleic acids, especially when non-canonical structures and nucleic acid complexes are considered. Here, we present an ab initio approach for predicting proton chemical shifts of arbitrary nucleic acid structures based on state-of-the-art fragment-based quantum chemical calculations. We tested our prediction method on a diverse set of nucleic acid structures including double-stranded DNA, hairpins, DNA/protein complexes and chemically-modified DNA. Overall, our quantum chemical calculations yield highly/very accurate predictions with mean absolute deviations of 0.3-0.6 ppm and correlation coefficients (r(2)) usually above 0.9. This will allow for identifying misassignments and validating 3D structures. Furthermore, our calculations reveal that chemical shifts of protons involved in hydrogen bonding are predicted significantly less accurately. This is in part caused by insufficient inclusion of solvation effects. However, it also points toward shortcomings of current force fields used for structure determination of nucleic acids. Our quantum chemical calculations could therefore provide input for force field optimization. Y1 - 2014 U6 - https://doi.org/10.1093/nar/gku1006 SN - 0305-1048 SN - 1362-4962 VL - 42 IS - 22 PB - Oxford Univ. Press CY - Oxford ER - TY - JOUR A1 - Kleinpeter, Erich A1 - Koch, Andreas A1 - Schulz, Stefanie A1 - Wacker, Philipp T1 - Interplay of para- and diatropic ring currents [(anti)aromaticity] of macrocyclic rings subject to conformational influences, further annelation and hydrogenation of aromatic ring moieties JF - Tetrahedron N2 - The spatial magnetic properties (Through Space NMR Shieldings-TSNMRS) of a variety of porphyrins, hemiporphyrazines and tetraoxo[8]circulenes have been computed, visualized as Iso-chemical Shielding Surfaces (ICSS) of various size and direction, and were examined subject to the interplay of present (para)-diatropic ring currents [(anti)aromaticity] and influences on the latter property originating from the macrocyclic ring conformation, further annelation and partial to complete hydrogenation of aromatic ring moieties. Caution seems to be indicated when concluding from a single NICS parameter to present (para)diatropic ring currents [(anti)aromaticity]. (C) 2014 Elsevier Ltd. All rights reserved. KW - Porphyrins KW - Hemiporphyrazines KW - Tetraoxo[8]circulenes KW - (Anti)aromaticity KW - Anisotropy effect KW - Theoretical calculations Y1 - 2014 U6 - https://doi.org/10.1016/j.tet.2014.10.018 SN - 0040-4020 VL - 70 IS - 48 SP - 9230 EP - 9239 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Strehmel, Veronika A1 - Berdzinski, Stefan A1 - Rexhausen, Hans T1 - Interactions between ionic liquids and radicals JF - Journal of molecular liquids N2 - Ionic liquids were investigated with both stable radicals on the basis of 2,2,6,6-tetramethylpiperidine-1-yloxyl (TEMPO) and photogenerated lophyl radicals. The ionic liquids are composed either of bis(trifluoromethylsulfonyl)imide (NTf2) as anion and various cations or they contain an imidazolium ion in combination with various anions. The cations include imidazolium, pyrrolidinium, piperidinium, polymethine or ammonium ions. Furthermore, BF4-, PF6-, triflate, camphorsulfonate, lactate, tosylate or tris(pentafluoroethyl) trifluorophosphate (FAP) are the counter ions in the imidazolium salts. The structural variation of the ionic liquids results in differences in glass formation, semiaystallinity, or crystallinity, as well as in viscosity differences. Furthermore, a vinyl substituent at the imidazolium ion and a methacryloyloxyethyl substituent at the ammonium ion result in polymerizable ionic liquids that were converted via a radical mechanism in amorphous polymerized ionic liquids with a glass transition temperature, which is significantly higher compared to the ionic liquids. An additional substituent at TEMPO causes additional hydrogen bond formation or additional Coulomb interactions with the individual ions of the ionic liquids compared to TEMPO. This influences the mobility of these radicals in the ionic liquid expressed by differences in the average rotational correlation time (T-rot). The mobility of the radicals in the ionic liquids as function of the temperature describes ionic liquids either as continuum in analogy to molecular solvents using the Stokes-Einstein model, that is the case for 1-butyl-3-methylimidazolium NTf2, or as medium where free volume effects are important for the mobility of a solute in the ionic liquid using the model of Spernol, Gierer, and Wirtz. The 1-butyl-3-methylimidazolium BF4- fits well into the latter. Furthermore, the isotropic hyperfine coupling constant (A(iso)(N-14)) of the stable radicals gives information about micropolarity of the ionic liquids only if the mobility of the radical is high enough in the ionic liquid. In addition to the rotational mobility of the stable radicals, the photogenerated lophyl radicals give information about translational diffusion of radicals and solvent cage effects in the ionic liquids. The application of the Eyring equation results mostly in the expected negative values of the activation entropy for the transition state that is typical for bimolecular reactions. Only few examples show a less negative or positive activation entropy for the bimolecular reaction, which may be attributed to radical recombination within the solvent cage to a high extent. The results obtained during investigation of radicals in ionic liquids are important to understand the radical processes in ionic liquids that may occur for example in dye sensitized solar cells, photo or thermally induced reactions or radical polymerizations in ionic liquids. KW - Ionic liquids KW - Radicals KW - Spin probes KW - Polymerized ionic liquids KW - Microviscosity KW - Micropolarity Y1 - 2014 U6 - https://doi.org/10.1016/j.molliq.2013.12.007 SN - 0167-7322 SN - 1873-3166 VL - 192 SP - 153 EP - 170 PB - Elsevier CY - Amsterdam ER - TY - INPR A1 - Riemer, Martin T1 - Allyl alkyl carbonates T2 - Synlett : accounts and rapid communications in synthetic organic chemistry Y1 - 2014 U6 - https://doi.org/10.1055/s-0033-1340862 SN - 0936-5214 SN - 1437-2096 VL - 25 IS - 7 SP - 1041 EP - 1042 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Eisold, Ursula A1 - Kupstat, Annette A1 - Klier, Dennis Tobias A1 - Primus, Philipp-A. A1 - Pschenitza, Michael A1 - Niessner, Reinhard A1 - Knopp, Dietmar A1 - Kumke, Michael Uwe T1 - Probing the physicochemical interactions of 3-hydroxy-benzo[a]pyrene with different monoclonal and recombinant antibodies by use of fluorescence line-narrowing spectroscopy JF - Analytical & bioanalytical chemistry N2 - Characterization of interactions between antigens and antibodies is of utmost importance both for fundamental understanding of the binding and for development of advanced clinical diagnostics. Here, fluorescence line-narrowing (FLN) spectroscopy was used to study physicochemical interactions between 3-hydroxybenzo[a]pyrene (3OH-BaP, as antigen) and a variety of solvent matrices (as model systems) or anti-polycyclic aromatic hydrocarbon antibodies (anti-PAH). We focused the studies on the specific physicochemical interactions between 3OH-BaP and different, previously obtained, monoclonal and recombinant anti-PAH antibodies. Control experiments performed with non-binding monoclonal antibodies and bovine serum albumin (BSA) indicated that nonspecific interactions did not affect the FLN spectrum of 3OH-BaP. The spectral positions and relative intensities of the bands in the FLN spectra are highly dependent on the molecular environment of the 3OH-BaP. The FLN bands correlate with different vibrational modes of 3OH-BaP which are affected by interactions with the molecular environment (pi-pi interactions, H-bonding, or van-der-Waals forces). Although the analyte (3OH-BaP) was the same for all the antibodies investigated, different binding interactions could be identified from the FLN spectra on the basis of structural flexibility and conformational multiplicity of the antibodies' paratopes. KW - FLNS KW - Antibody KW - Paratope KW - Hapten KW - Polycyclic aromatic hydrocarbons Y1 - 2014 U6 - https://doi.org/10.1007/s00216-013-7584-8 SN - 1618-2642 SN - 1618-2650 VL - 406 IS - 14 SP - 3387 EP - 3394 PB - Springer CY - Heidelberg ER -