TY - JOUR A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Gierlinger, Notburga A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Improvement of wood material properties via in situ polymerization of styrene into tosylated cell walls JF - RSC Advances N2 - As an engineering material derived from renewable resources, wood possesses excellent mechanical properties in view of its light weight but also has some disadvantages such as low dimensional stability upon moisture changes and low durability against biological attack. Polymerization of hydrophobic monomers in the cell wall is one of the potential approaches to improve the dimensional stability of wood. A major challenge is to insert hydrophobic monomers into the hydrophilic environment of the cell walls, without increasing the bulk density of the material due to lumen filling. Here, we report on an innovative and simple method to insert styrene monomers into tosylated cell walls (i.e. -OH groups from natural wood polymers are reacted with tosyl chloride) and carry out free radical polymerization under relatively mild conditions, generating low wood weight gains. In-depth SEM and confocal Raman microscopy analysis are applied to reveal the distribution of the polystyrene in the cell walls and the lumen. The embedding of polystyrene in wood results in reduced water uptake by the wood cell walls, a significant increase in dimensional stability, as well as slightly improved mechanical properties measured by nanoindentation. Y1 - 2014 U6 - https://doi.org/10.1039/c4ra00741g SN - 2046-2069 VL - 4 IS - 25 SP - 12981 EP - 12988 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Hass, Philipp A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Fully biodegradable modification of wood for improvement of dimensional stability and water absorption properties by poly(epsilon-caprolactone) grafting into the cell walls JF - Green chemistry : an international journal and green chemistry resource N2 - Materials derived from renewable resources are highly desirable in view of more sustainable manufacturing. Among the available natural materials, wood is one of the key candidates, because of its excellent mechanical properties. However, wood and wood-based materials in engineering applications suffer from various restraints, such as dimensional instability upon humidity changes. Several wood modification treatments increase water repellence, but the insertion of hydrophobic polymers can result in a composite material which cannot be considered as renewable anymore. In this study, we report on the grafting of the fully biodegradable poly(epsilon-caprolactone) (PCL) inside the wood cell walls by Sn(Oct)(2) catalysed ring-opening polymerization (ROP). The presence of polyester chains within the wood cell wall structure is monitored by confocal Raman imaging and spectroscopy as well as scanning electron microscopy. Physical tests reveal that the modified wood is more hydrophobic due to the bulking of the cell wall structure with the polyester chains, which results in a novel fully biodegradable wood material with improved dimensional stability. Y1 - 2014 U6 - https://doi.org/10.1039/c4gc00194j SN - 1463-9262 SN - 1463-9270 VL - 16 IS - 6 SP - 3313 EP - 3321 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Kovach, Ildyko A1 - Koetz, Joachim A1 - Friberg, Stig E. T1 - Janus emulsions stabilized by phospholipids JF - Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects N2 - Janus emulsions were formed by mixing three immiscible liquids; this implies two oil components (i.e. olive oil (00) and silicone oil (SiO)) with water in presence of interfacial active components. The morphology and size of Janus droplets formed strongly depended on the type of surfactant used. In presence of a non-ionic surfactant, i.e. Tween 80, large engulfed Janus droplets were formed. By adding phospholipids to the system the droplet size was decreased and more stable Janus droplets formed. Interfacial tension measurements carried out using a spinning drop apparatus and a ring tensiometer demonstrate that interfacial tension is the most important factor controlling the size, morphology and stability of Janus droplets. When the interfacial tension between oil and water becomes <= 1 mN/m, smaller Janus droplets are formed. Such conditions are fulfilled when phospholipids are used in combination with non-ionic surfactant Tween 80. The morphology of the double droplets is predominantly controlled by the viscosity and interfacial tension between the two oil phases. By using different types of phospholipids, i.e. asolectin and lecithin instead of a more concentrated phosphatidylcholine (phospholipon), the interfacial tension is decreased and different morphologies of engulfing can be observed. KW - Janus emulsions KW - Spinning drop KW - Interfacial tension KW - Phospholipids Y1 - 2014 U6 - https://doi.org/10.1016/j.colsurfa.2013.08.065 SN - 0927-7757 SN - 1873-4359 VL - 441 SP - 66 EP - 71 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kosmella, Sabine A1 - Venus, Jane A1 - Hahn, Jennifer A1 - Prietzel, Claudia Christina A1 - Koetz, Joachim T1 - Low-temperature synthesis of polyethyleneimine-entrapped CdS quantum dots JF - Chemical physics letters N2 - This Letter is focused on the one-pot formation of CdS nanoparticles in aqueous medium in presence of polyethyleneimine (PEI). Quantum dots can be obtained by adding a pre-cooled aqueous Na2S solution to a pre-cooled aqueous CdCl2 solution dropwise in presence of PEI. Field flow fractionation in combination with TEM experiments show a time dependent agglomeration of individual quantum dots from 1.6 nm up to 3.2 nm in size. The hyperbranched PEI of moderate molar mass (>20000 g/mol) is an excellent polymer to prevent a further increase of the particle size. Therefore, stable fluorescent PEI-capped CdS quantum dots are available. Y1 - 2014 U6 - https://doi.org/10.1016/j.cplett.2013.12.019 SN - 0009-2614 SN - 1873-4448 VL - 592 SP - 114 EP - 119 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hasinovic, Hida A1 - Boggs, Cami A1 - Friberg, Stig E. A1 - Kovach, Ildiko A1 - Koetz, Joachim T1 - Janus emulsions from a one-step process; optical microscopy images JF - Journal of dispersion science and technology N2 - The optical microscopy images of an emulsion are commonly distorted when viewed between a cover glass and a planar microscopy slide. An alternative method is to place the sample on a slide with a cavity, which in turn suffers from incomplete information for high internal phase ratio (HIPR) emulsions, due to the inevitable crowding of the drops. This problem is particularly acute for more complex emulsions, such as those with Janus drops, for which a detailed image of the drop is essential. A number of publications have recently described Janus emulsions prepared by a one-step high energy emulsification process with microscopy images obtained by the sample between a planar slide and a cover glass. The correlation to the morphology of emulsions in bulk of these images is critical, but, so far, a potential equivalence has not been established. Since the images are central in order to understand why Janus emulsions should form under such conditions, the need to ascertain any such association is urgent. With this contribution, we compare images from different microscopy methods to those of gently diluted HIPR emulsions. The results reveal that the images of the emulsion samples between a cover glass and a planar microscope slide actually present a realistic representation of the drop topology in bulk emulsions. KW - Janus drops KW - Emulsification KW - microemulsions KW - emulsion microscopy Y1 - 2014 U6 - https://doi.org/10.1080/01932691.2013.801019 SN - 0193-2691 SN - 1532-2351 VL - 35 IS - 5 SP - 613 EP - 618 PB - Taylor & Francis Group CY - Philadelphia ER - TY - JOUR A1 - Hasinovic, H. A1 - Friberg, S. E. A1 - Kovach, Ildyko A1 - Koetz, Joachim T1 - Destabilization of a dual emulsion to form a Janus emulsion JF - Colloid and polymer science : official journal of the Kolloid-Gesellschaft N2 - A vegetable oil (VO) was added to an emulsion of silicone oil in water (SO/W) with mixing limited to once turning the test tube upside down. Initially, the VO was dispersed into virtually centimeter-sized drops and the emulsion contained effectively no Janus drops, while after 1 h of agitation at a low level to prevent creaming, drops of 50-100-mu m size of the two oils were observed: in addition to an insignificant number of Janus drops. The topology of the latter showed them to emanate from flocculated individual drops of the two oils, but with no discernible effect by the interfacial tension equilibrium on the drop topology. Continued gentle mixing gave increasing fraction of Janus drops of increased size with a topology gradually approaching the one expected from the interfacial equilibrium at the contact line. The spontaneous formation of Janus drops indicated a reduction of the interfacial free energy in the process and the interfacial energy difference between separate and Janus drops was calculated for an appropriate range of interfacial tensions and for all oil fractions. The calculations enabled a distinction of the decrease due to interfacial area changes from the reduction of interfacial tensions per se, with the latter only a minor fraction. KW - Emulsion destabilization KW - Janus emulsions KW - Interfacial equilibrium KW - Microfluidics Y1 - 2014 U6 - https://doi.org/10.1007/s00396-014-3263-3 SN - 0303-402X SN - 1435-1536 VL - 292 IS - 9 SP - 2319 EP - 2324 PB - Springer CY - New York ER - TY - JOUR A1 - Schulze, Nicole A1 - Appelhans, D. A1 - Tiersch, Brigitte A1 - Koetz, Joachim T1 - Morphological transformation of vesicles into tubular structures by adding polyampholytes or dendritic glycopolymers JF - Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects N2 - For the first time tubulating properties of spherical dendritic glycopolymers and linear alternating polyampholytes against non-uniform negatively charged giant vesicles are proven by light microscopy and cryo-scanning electron microscopy study. Real time observation of the morphological transformation from giant vesicles to tubular structures, simulating morphogenesis in living cells, is given by using the cationic and H-bond active dendritic glycopolymer accompanied by reducing the size of the giant vesicles and the evidence of vesicle-vesicle interaction which was only postulated in a previous study. Similar morphogenesis of non-uniform giant vesicles into tubular network structure can be observed by using a polyampholyte in the stretched conformation at pH 9. Pearl necklace and tubular network structure formation are also observed by applying anionic vesicles of significant smaller dimensions with average size dimensions of 35 nm, after adding the polyampholyte at pH 9. However, the fitting accuracy between the functional groups along the backbone chain of the polyampholyte on one side and the vesicle surface on the other side is of high importance for the transformation process by using polyampholytes. The resulting tubular and network structures offer new fields of application as microfluidic transport channels or template phases for the shape controlled formation of nanoparticles. (C) 2014 Elsevier B.V. All rights reserved. KW - Alternating polyampholytes KW - Maltose-modified PEI KW - Network structure KW - Template phase KW - Cryo-SEM KW - DLS Y1 - 2014 U6 - https://doi.org/10.1016/j.colsurfa.2014.06.007 SN - 0927-7757 SN - 1873-4359 VL - 457 SP - 326 EP - 332 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Gierlinger, Notburga A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Improvement of wood material properties via in situ polymerization of styrene into tosylated cell walls N2 - As an engineering material derived from renewable resources, wood possesses excellent mechanical properties in view of its light weight but also has some disadvantages such as low dimensional stability upon moisture changes and low durability against biological attack. Polymerization of hydrophobic monomers in the cell wall is one of the potential approaches to improve the dimensional stability of wood. A major challenge is to insert hydrophobic monomers into the hydrophilic environment of the cell walls, without increasing the bulk density of the material due to lumen filling. Here, we report on an innovative and simple method to insert styrene monomers into tosylated cell walls (i.e. –OH groups from natural wood polymers are reacted with tosyl chloride) and carry out free radical polymerization under relatively mild conditions, generating low wood weight gains. In-depth SEM and confocal Raman microscopy analysis are applied to reveal the distribution of the polystyrene in the cell walls and the lumen. The embedding of polystyrene in wood results in reduced water uptake by the wood cell walls, a significant increase in dimensional stability, as well as slightly improved mechanical properties measured by nanoindentation. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 274 Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-98736 ER - TY - GEN A1 - Ermeydan, Mahmut Ali A1 - Cabane, Etienne A1 - Hass, Philipp A1 - Koetz, Joachim A1 - Burgert, Ingo T1 - Fully biodegradable modification of wood for improvement of dimensional stability and water absorption properties by poly(ε-caprolactone) grafting into the cell walls N2 - Materials derived from renewable resources are highly desirable in view of more sustainable manufacturing. Among the available natural materials, wood is one of the key candidates, because of its excellent mechanical properties. However, wood and wood-based materials in engineering applications suffer from various restraints, such as dimensional instability upon humidity changes. Several wood modification treatments increase water repellence, but the insertion of hydrophobic polymers can result in a composite material which cannot be considered as renewable anymore. In this study, we report on the grafting of the fully biodegradable poly(ε-caprolactone) (PCL) inside the wood cell walls by Sn(Oct)2 catalysed ring-opening polymerization (ROP). The presence of polyester chains within the wood cell wall structure is monitored by confocal Raman imaging and spectroscopy as well as scanning electron microscopy. Physical tests reveal that the modified wood is more hydrophobic due to the bulking of the cell wall structure with the polyester chains, which results in a novel fully biodegradable wood material with improved dimensional stability. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 270 KW - ring-opening polymerization KW - confocal raman microscopy KW - epsilon-caprolactone KW - mechanical-properties KW - structural-characterization KW - stannous octoate KW - copolymers KW - degradation KW - composites KW - cellulose Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-97265 SP - 3313 EP - 3321 ER -