TY - JOUR A1 - Inal, Sahika A1 - Chiappisi, Leonardo A1 - Kölsch, Jonas D. A1 - Kraft, Mario A1 - Appavou, Marie-Sousai A1 - Scherf, Ullrich A1 - Wagner, Manfred A1 - Hansen, Michael Ryan A1 - Gradzielski, Michael A1 - Laschewsky, André A1 - Neher, Dieter T1 - Temperature-regulated fluorescence and association of an Oligo(ethyleneglycol)methacrylate-based copolymer with a conjugated Polyelectrolyte-the effect of solution ionic strength JF - The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces & biophysical chemistry N2 - Aqueous mixtures of a dye-labeled non-ionic thermoresponsive copolymer and a conjugated cationic polyelectrolyte are shown to exhibit characteristic changes in fluorescence properties in response to temperature and to the presence of salts, enabling a double-stimuli responsiveness. In such mixtures at room temperature, i.e., well below the lower critical solution temperature (LCST), the emission of the dye is strongly quenched due to energy transfer to the polycation, pointing to supramolecular interactions between the two macromolecules. Increasing the concentration of salts weakens the interpolymer interactions, the extent of which is simultaneously monitored from the change in the relative emission intensity of the components. When the mixture is heated above its LCST, the transfer efficiency is significantly reduced, signaling a structural reorganization process, however, surprisingly only if the mixture contains salt ions. To elucidate the reasons behind such thermo- and ion-sensitive fluorescence characteristics, we investigate the effect of salts of alkali chlorides, in particular of NaCl, on the association behavior of these macromolecules before and after the polymer phase transition by a combination of UV-vis, fluorescence, and H-1 NMR spectroscopy with light scattering and small-angle neutron scattering measurements. Y1 - 2013 U6 - https://doi.org/10.1021/jp408864s SN - 1520-6106 VL - 117 IS - 46 SP - 14576 EP - 14587 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Li, Hongguang A1 - Babu, Sukumaran Santhosh A1 - Turner, Sarah T. A1 - Neher, Dieter A1 - Hollamby, Martin J. A1 - Seki, Tomohiro A1 - Yagai, Shiki A1 - Deguchi, Yonekazu A1 - Möhwald, Helmuth A1 - Nakanishi, Takashi T1 - Alkylated-C-60 based soft materials regulation of self-assembly and optoelectronic properties by chain branching JF - Journal of materials chemistry : C, Materials for optical and electronic devices N2 - Derivatization of fullerene (C-60) with branched aliphatic chains softens C-60-based materials and enables the formation of thermotropic liquid crystals and room temperature nonvolatile liquids. This work demonstrates that by carefully tuning parameters such as type, number and substituent position of the branched chains, liquid crystalline C-60 materials with mesophase temperatures suited for photovoltaic cell fabrication and room temperature nonvolatile liquid fullerenes with tunable viscosity can be obtained. In particular, compound 1, with branched chains, exhibits a smectic liquid crystalline phase extending from 84 degrees C to room temperature. Analysis of bulk heterojunction (BHJ) organic solar cells with a ca. 100 nm active layer of compound 1 and poly(3-hexylthiophene) (P3HT) as an electron acceptor and an electron donor, respectively, reveals an improved performance (power conversion efficiency, PCE: 1.6 + 0.1%) in comparison with another compound, 10 (PCE: 0.5 + 0.1%). The latter, in contrast to 1, carries linear aliphatic chains and thus forms a highly ordered solid lamellar phase at room temperature. The solar cell performance of 1 blended with P3HT approaches that of PCBM/P3HT for the same active layer thickness. This indicates that C-60 derivatives bearing branched tails are a promising class of electron acceptors in soft (flexible) photovoltaic devices. Y1 - 2013 U6 - https://doi.org/10.1039/c3tc00066d SN - 2050-7526 VL - 1 IS - 10 SP - 1943 EP - 1951 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Hoffmann, Sebastian T. A1 - Jaiser, Frank A1 - Hayer, Anna A1 - Baessler, Heinz A1 - Unger, Thomas A1 - Athanasopoulos, Stavros A1 - Neher, Dieter A1 - Koehler, Anna T1 - How Do Disorder, Reorganization, and Localization Influence the Hole Mobility in Conjugated Copolymers? JF - JOURNAL OF THE AMERICAN CHEMICAL SOCIETY N2 - In order to unravel the intricate interplay between disorder effects, molecular reorganization, and charge carrier localization, a comprehensive study was conducted on hole transport in a series of conjugated alternating phenanthrene indenofluorene copolymers. Each polymer in the series contained one further comonomer comprising monoamines, diamines, or amine-free structures, whose influence on the electronic, optical, and charge transport properties was studied. The series covered a wide range of highest occupied molecular orbital (HOMO) energies as determined by cyclovoltammetry. The mobility, inferred from time-of-flight (ToF) experiments as a function of temperature and electric field, was found to depend exponentially on the HOMO energy. Since possible origins for this effect include energetic disorder, polaronic effects, and wave function localization, the relevant parameters were determined using a range of methods. Disorder and molecular reorganization were established first by an analysis of absorption and emission measurements and second by an analysis of the ToF measurements. In addition, density functional theory calculations were carried out to determine how localized or delocalized holes on a polymer chain are and to compare calculated reorganization energies with those that have been inferred from optical spectra. In summary, we conclude that molecular reorganization has little effect on the hole mobility in this system while both disorder effects and hole localization in systems with low-lying HOMOs are predominant. In particular, as the energetic disorder is comparable for the copolymers, the absolute value of the hole mobility at room temperature is determined by the hole localization associated with the triarylamine moieties. Y1 - 2013 U6 - https://doi.org/10.1021/ja308820j SN - 0002-7863 VL - 135 IS - 5 SP - 1772 EP - 1782 PB - AMER CHEMICAL SOC CY - WASHINGTON ER - TY - JOUR A1 - Inal, Sahika A1 - Kölsch, Jonas D. A1 - Chiappisi, Leonardo A1 - Janietz, Dietmar A1 - Gradzielski, Michael A1 - Laschewsky, André A1 - Neher, Dieter T1 - Structure-related differences in the temperature-regulated fluorescence response of LCST type polymers N2 - We demonstrate new fluorophore-labelled materials based on acrylamide and on oligo(ethylene glycol) (OEG) bearing thermoresponsive polymers for sensing purposes and investigate their thermally induced solubility transitions. It is found that the emission properties of the polarity-sensitive (solvatochromic) naphthalimide derivative attached to three different thermoresponsive polymers are highly specific to the exact chemical structure of the macromolecule. While the dye emits very weakly below the LCST when incorporated into poly(N-isopropylacrylamide) (pNIPAm) or into a polyacrylate backbone bearing only short OEG side chains, it is strongly emissive in polymethacrylates with longer OEG side chains. Heating of the aqueous solutions above their cloud point provokes an abrupt increase of the fluorescence intensity of the labelled pNIPAm, whereas the emission properties of the dye are rather unaffected as OEG-based polyacrylates and methacrylates undergo phase transition. Correlated with laser light scattering studies, these findings are ascribed to the different degrees of pre-aggregation of the chains at low temperatures and to the extent of dehydration that the phase transition evokes. It is concluded that although the temperature-triggered changes in the macroscopic absorption characteristics, related to large-scale alterations of the polymer chain conformation and aggregation, are well detectable and similar for these LCST-type polymers, the micro-environment provided to the dye within each polymer network differs substantially. Considering sensing applications, this finding is of great importance since the temperature-regulated fluorescence response of the polymer depends more on the macromolecular architecture than the type of reporter fluorophore. Y1 - 2013 UR - http://pubs.rsc.org/en/content/articlepdf/2013/tc/c3tc31304b U6 - https://doi.org/10.1039/C3TC31304B ER - TY - JOUR A1 - Schubert, Marcel A1 - Preis, Eduard A1 - Blakesley, James C. A1 - Pingel, Patrick A1 - Scherf, Ullrich A1 - Neher, Dieter T1 - Mobility relaxation and electron trapping in a donor/acceptor copolymer JF - Physical review : B, Condensed matter and materials physics N2 - To address the nature of charge transport and the origin of severe (intrinsic) trapping in electron-transporting polymers, transient and steady-state charge transport measurements have been conducted on the prototype donor/acceptor copolymer poly[2,7-(9,9-dialkyl-fluorene)-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PFTBTT). A charge-generation layer technique is used to selectively address transport of the desired charge carrier type, to perform time-of-flight measurements on samples with < 200 nm thickness, and to combine the time-of-flight and the photocharge extraction by linearly increasing voltage (photo-CELIV) techniques to investigate charge carrier dynamics over a wide time range. Significant trapping of free electrons is observed in the bulk of dioctyl-substituted PFTBTT (alt-PF8TBTT), introducing a strong relaxation of the charge carrier mobility with time. We used Monte-Carlo simulation to simulate the measured transient data and found that all measurements can be modeled with a single parameter set, with the charge transport behavior determined by multiple trapping and detrapping of electrons in an exponential trap distribution. The influence of the concomitant mobility relaxation on the transient photocurrent characteristics in photo-CELIV experiments is discussed and shown to explain subtle features that were seen in former publications but were not yet assigned to electron trapping. Comparable studies on PFTBTT copolymers with chemical modifications of the side chains and backbone suggest that the observed electron trapping is not caused by a distinct chemical species but rather is related to interchain interactions. Y1 - 2013 U6 - https://doi.org/10.1103/PhysRevB.87.024203 SN - 1098-0121 VL - 87 IS - 2 PB - American Physical Society CY - College Park ER - TY - JOUR A1 - Inal, Sahika A1 - Kölsch, Jonas D. A1 - Selrie, Frank A1 - Schenk, Jörg A. A1 - Wischerhoff, Erik A1 - Laschewsky, André A1 - Neher, Dieter T1 - A water soluble fluorescent polymer as a dual colour sensor for temperature and a specific protein N2 - We present two thermoresponsive water soluble copolymers prepared via free radical statistical copolymerization of N-isopropylacrylamide (NIPAm) and of oligo(ethylene glycol) methacrylates (OEGMAs), respectively, with a solvatochromic 7-(diethylamino)-3-carboxy-coumarin (DEAC)-functionalized monomer. In aqueous solutions, the NIPAm-based copolymer exhibits characteristic changes in its fluorescence profile in response to a change in solution temperature as well as to the presence of a specific protein, namely an anti-DEAC antibody. This polymer emits only weakly at low temperatures, but exhibits a marked fluorescence enhancement accompanied by a change in its emission colour when heated above its cloud point. Such drastic changes in the fluorescence and absorbance spectra are observed also upon injection of the anti-DEAC antibody, attributed to the specific binding of the antibody to DEAC moieties. Importantly, protein binding occurs exclusively when the polymer is in the well hydrated state below the cloud point, enabling a temperature control on the molecular recognition event. On the other hand, heating of the polymer-antibody complexes releases a fraction of the bound antibody. In the presence of the DEAC-functionalized monomer in this mixture, the released antibody competitively binds to the monomer and the antibody-free chains of the polymer undergo a more effective collapse and inter-aggregation. In contrast, the emission properties of the OEGMA-based analogous copolymer are rather insensitive to the thermally induced phase transition or to antibody binding. These opposite behaviours underline the need for a carefully tailored molecular design of responsive polymers aimed at specific applications, such as biosensing. Y1 - 2013 UR - http://pubs.rsc.org/en/content/articlepdf/2013/tb/c3tb21245a U6 - https://doi.org/10.1039/c3tb21245a ER - TY - JOUR A1 - Lu, Guanghao A1 - Blakesley, James C. A1 - Himmelberger, Scott A1 - Pingel, Patrick A1 - Frisch, Johannes A1 - Lieberwirth, Ingo A1 - Salzmann, Ingo A1 - Oehzelt, Martin A1 - Di Pietro, Riccardo A1 - Salleo, Alberto A1 - Koch, Norbert A1 - Neher, Dieter T1 - Moderate doping leads to high performance of semiconductor/insulator polymer blend transistors JF - Nature Communications N2 - Polymer transistors are being intensively developed for next-generation flexible electronics. Blends comprising a small amount of semiconducting polymer mixed into an insulating polymer matrix have simultaneously shown superior performance and environmental stability in organic field-effect transistors compared with the neat semiconductor. Here we show that such blends actually perform very poorly in the undoped state, and that mobility and on/off ratio are improved dramatically upon moderate doping. Structural investigations show that these blend layers feature nanometre-scale semiconductor domains and a vertical composition gradient. This particular morphology enables a quasi three-dimensional spatial distribution of semiconductor pathways within the insulating matrix, in which charge accumulation and depletion via a gate bias is substantially different from neat semiconductor, and where high on-current and low off-current are simultaneously realized in the stable doped state. Adding only 5 wt% of a semiconducting polymer to a polystyrene matrix, we realized an environmentally stable inverter with gain up to 60. Y1 - 2013 U6 - https://doi.org/10.1038/ncomms2587 SN - 2041-1723 VL - 4 IS - 1-2 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Proctor, Christopher M. A1 - Kim, Chunki A1 - Neher, Dieter A1 - Thuc-Quyen Nguyen, T1 - Nongeminate recombination and charge transport limitations in diketopyrrolopyrrole-based solution-processed small molecule solar cells JF - Advanced functional materials N2 - Charge transport and nongeminate recombination are investigated in two solution-processed small molecule bulk heterojunction solar cells consisting of diketopyrrolopyrrole (DPP)-based donor molecules, mono-DPP and bis-DPP, blended with [6,6]-phenyl-C71-butyric acid methyl ester (PCBM). While the bis-DPP system exhibits a high fill factor (62%) the mono-DPP system suffers from pronounced voltage dependent losses, which limit both the fill factor (46%) and short circuit current. A method to determine the average charge carrier density, recombination current, and effective carrier lifetime in operating solar cells as a function of applied bias is demonstrated. These results and light intensity measurements of the current-voltage characteristics indicate that the mono-DPP system is severely limited by nongeminate recombination losses. Further analysis reveals that the most significant factor leading to the difference in fill factor is the comparatively poor hole transport properties in the mono-DPP system (2 x 10(-5) cm(2) V-1 s(-1) versus 34 x 10(-5) cm(2) V-1 s(-1)). These results suggest that future design of donor molecules for organic photovoltaics should aim to increase charge carrier mobility thereby enabling faster sweep out of charge carriers before they are lost to nongeminate recombination. KW - charge transport KW - solar cells KW - photovoltaic devices KW - organic electronics KW - characterization tools Y1 - 2013 U6 - https://doi.org/10.1002/adfm.201202643 SN - 1616-301X SN - 1616-3028 VL - 23 IS - 28 SP - 3584 EP - 3594 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Li, Hongguang A1 - Babu, Sukumaran Santhosh A1 - Turner, Sarah T. A1 - Neher, Dieter A1 - Hollamby, Martin J. A1 - Tomohito, Seki A1 - Yagai, Shiki A1 - deguchi, Yonekazu A1 - Möhwald, Helmuth A1 - Nakanishi, Takashi T1 - Alkylated-C60 based soft materials: regulation of self-assembly and optoelectronic properties by chain branching N2 - Derivatization of fullerene (C60) with branched aliphatic chains softens C60-based materials and enables the formation of thermotropic liquid crystals and room temperature nonvolatile liquids. This work demonstrates that by carefully tuning parameters such as type, number and substituent position of the branched chains, liquid crystalline C60 materials with mesophase temperatures suited for photovoltaic cell fabrication and room temperature nonvolatile liquid fullerenes with tunable viscosity can be obtained. In particular, compound 1, with branched chains, exhibits a smectic liquid crystalline phase extending from 84°C to room temperature. Analysis of bulk heterojunction (BHJ) organic solar cells with a ca. 100 nm active layer of compound 1 and poly(3-hexylthiophene) (P3HT) as an electron acceptor and an electron donor, respectively, reveals an improved performance (power conversion efficiency, PCE: 1.6 ñ 0.1%) in comparison with another compound, 10 (PCE: 0.5 ñ 0.1%). The latter, in contrast to 1, carries linear aliphatic chains and thus forms a highly ordered solid lamellar phase at room temperature. The solar cell performance of 1 blended with P3HT approaches that of PCBM/P3HT for the same active layer thickness. This indicates that C60 derivatives bearing branched tails are a promising class of electron acceptors in soft (flexible) photovoltaic devices. Y1 - 2013 UR - http://pubs.rsc.org/en/content/articlepdf/2013/tc/c3tc00066d U6 - https://doi.org/10.1039/C3TC00066D ER - TY - JOUR A1 - Inal, Sahika A1 - Koelsch, Jonas D. A1 - Chiappisi, Leonardo A1 - Janietz, Dietmar A1 - Gradzielski, Michael A1 - Laschewsky, André A1 - Neher, Dieter T1 - Structure-related differences in the temperature-regulated fluorescence response of LCST type polymers JF - Journal of materials chemistry : C, Materials for optical and electronic devices N2 - We demonstrate new fluorophore-labelled materials based on acrylamide and on oligo(ethylene glycol) (OEG) bearing thermoresponsive polymers for sensing purposes and investigate their thermally induced solubility transitions. It is found that the emission properties of the polarity-sensitive (solvatochromic) naphthalimide derivative attached to three different thermoresponsive polymers are highly specific to the exact chemical structure of the macromolecule. While the dye emits very weakly below the LCST when incorporated into poly(N-isopropylacrylamide) (pNIPAm) or into a polyacrylate backbone bearing only short OEG side chains, it is strongly emissive in polymethacrylates with longer OEG side chains. Heating of the aqueous solutions above their cloud point provokes an abrupt increase of the fluorescence intensity of the labelled pNIPAm, whereas the emission properties of the dye are rather unaffected as OEG-based polyacrylates and methacrylates undergo phase transition. Correlated with laser light scattering studies, these findings are ascribed to the different degrees of pre-aggregation of the chains at low temperatures and to the extent of dehydration that the phase transition evokes. It is concluded that although the temperature-triggered changes in the macroscopic absorption characteristics, related to large-scale alterations of the polymer chain conformation and aggregation, are well detectable and similar for these LCST-type polymers, the micro-environment provided to the dye within each polymer network differs substantially. Considering sensing applications, this finding is of great importance since the temperature-regulated fluorescence response of the polymer depends more on the macromolecular architecture than the type of reporter fluorophore. Y1 - 2013 U6 - https://doi.org/10.1039/c3tc31304b SN - 2050-7526 VL - 1 IS - 40 SP - 6603 EP - 6612 PB - Royal Society of Chemistry CY - Cambridge ER -