TY - JOUR A1 - Ozcelikay, Goksu A1 - Kurbanoglu, Sevinc A1 - Yarman, Aysu A1 - Scheller, Frieder W. A1 - Ozkan, Sibel A. T1 - Au-Pt nanoparticles based molecularly imprinted nanosensor for electrochemical detection of the lipopeptide antibiotic drug Daptomycin JF - Sensors and actuators : B, Chemical N2 - In this work, a novel electrochemical molecularly imprinted polymer (MIP) sensor for the detection of the lipopeptide antibiotic Daptomycin (DAP) is presented which integrates gold decorated platinum nanoparticles (Au-Pt NPs) into the nanocomposite film. The sensor was prepared by electropolymerization of o-phenylenediamine (o-PD) in the presence of DAP using cyclic voltammetry. Cyclic voltammetry and differential pulse voltammetry were applied to follow the changes in the MIP-layer related to rebinding and removal of the target DAP by using the redox marker [Fe(CN)(6)](3-/4-). Under optimized operational conditions, the MIP/Au-Pt NPs/ GCE nanosensor exhibits a linear response in the range of 1-20 pM towards DAP. The limit of detection and limit of quantification were determined to be 0.161pM +/- 0.012 and 0.489pM +/- 0.012, respectively. The sensitivity towards the antibiotics Vancomycin and Erythromycin and the amino acids glycine and tryptophan was below 7 percent as compared with DAP. Moreover, the nanosensor was also successfully used for the detection of DAP in deproteinated human serum samples. KW - molecularly imprinted polymer KW - Daptomycin KW - platinum nanoparticles KW - gold KW - nanoparticles KW - modified electrodes Y1 - 2020 U6 - https://doi.org/10.1016/j.snb.2020.128285 SN - 0925-4005 VL - 320 PB - Elsevier Science CY - Amsterdam ER - TY - GEN A1 - Pudell, Jan-Etienne A1 - Maznev, Alexei A1 - Herzog, Marc A1 - Kronseder, M. A1 - Back, Christian A1 - Malinowski, Gregory A1 - von Reppert, Alexander A1 - Bargheer, Matias T1 - Layer specific observation of slow thermal equilibration in ultrathin metallic nanostructures by femtosecond X-ray diffraction T2 - Postprints der Universität Potsdam Mathematisch-Naturwissenschaftliche Reihe N2 - Ultrafast heat transport in nanoscale metal multilayers is of great interest in the context of optically induced demagnetization, remagnetization and switching. If the penetration depth of light exceeds the bilayer thickness, layer-specific information is unavailable from optical probes. Femtosecond diffraction experiments provide unique experimental access to heat transport over single digit nanometer distances. Here, we investigate the structural response and the energy flow in the ultrathin double-layer system: gold on ferromagnetic nickel. Even though the excitation pulse is incident from the Au side, we observe a very rapid heating of the Ni lattice, whereas the Au lattice initially remains cold. The subsequent heat transfer from Ni to the Au lattice is found to be two orders of magnitude slower than predicted by the conventional heat equation and much slower than electron-phonon coupling times in Au. We present a simplified model calculation highlighting the relevant thermophysical quantities. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 797 KW - thin magnetic layers KW - optical-excitation KW - heat-capacity KW - electron KW - gold KW - dynamics Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-426233 SN - 1866-8372 IS - 797 ER - TY - JOUR A1 - Krüger, Stefanie A1 - Schwarze, Michael A1 - Baumann, Otto A1 - Günter, Christina A1 - Bruns, Michael A1 - Kübel, Christian A1 - Szabo, Dorothee Vinga A1 - Meinusch, Rafael A1 - Bermudez, Veronica de Zea A1 - Taubert, Andreas T1 - Bombyx mori silk/titania/gold hybrid materials for photocatalytic water splitting BT - combining renewable raw materials with clean fuels JF - Beilstein journal of nanotechnology N2 - The synthesis, structure, and photocatalytic water splitting performance of two new titania (TiO2)/gold(Au)/Bombyx mori silk hybrid materials are reported. All materials are monoliths with diameters of up to ca. 4.5 cm. The materials are macroscopically homogeneous and porous with surface areas between 170 and 210 m(2)/g. The diameter of the TiO2 nanoparticles (NPs) - mainly anatase with a minor fraction of brookite - and the Au NPs are on the order of 5 and 7-18 nm, respectively. Addition of poly(ethylene oxide) to the reaction mixture enables pore size tuning, thus providing access to different materials with different photocatalytic activities. Water splitting experiments using a sunlight simulator and a Xe lamp show that the new hybrid materials are effective water splitting catalysts and produce up to 30 mmol of hydrogen per 24 h. Overall the article demonstrates that the combination of a renewable and robust scaffold such as B. mori silk with a photoactive material provides a promising approach to new monolithic photocatalysts that can easily be recycled and show great potential for application in lightweight devices for green fuel production. KW - Bombyx mori silk KW - gold KW - photocatalytic water splitting KW - titania Y1 - 2018 U6 - https://doi.org/10.3762/bjnano.9.21 SN - 2190-4286 VL - 9 SP - 187 EP - 204 PB - Beilstein-Institut zur Förderung der Chemischen Wissenschaften CY - Frankfurt, Main ER - TY - GEN A1 - Krüger, Stefanie A1 - Schwarze, Michael A1 - Baumann, Otto A1 - Günter, Christina A1 - Bruns, Michael A1 - Kübel, Christian A1 - Szabó, Dorothée Vinga A1 - Meinusch, Rafael A1 - de Zea Bermudez, Verónica A1 - Taubert, Andreas T1 - Bombyx mori silk/titania/gold hybrid materials for photocatalytic water splitting BT - combining renewable raw materials with clean fuels T2 - Postprints der Universität Potsdam Mathematisch-Naturwissenschaftliche Reihe N2 - The synthesis, structure, and photocatalytic water splitting performance of two new titania (TiO 2 )/gold(Au)/Bombyx mori silk hybrid materials are reported. All materials are monoliths with diameters of up to ca. 4.5 cm. The materials are macroscopically homogeneous and porous with surface areas between 170 and 210 m 2/g. The diameter of the TiO 2 nanoparticles (NPs) – mainly anatase with a minor fraction of brookite – and the Au NPs are on the order of 5 and 7–18 nm, respectively. Addition of poly(ethylene oxide) to the reaction mixture enables pore size tuning, thus providing access to different materials with different photocatalytic activities. Water splitting experiments using a sunlight simulator and a Xe lamp show that the new hybrid materials are effective water splitting catalysts and produce up to 30 mmol of hydrogen per 24 h. Overall the article demonstrates that the combination of a renewable and robust scaffold such as B. mori silk with a photoactive material provides a promising approach to new monolithic photocatalysts that can easily be recycled and show great potential for application in lightweight devices for green fuel production. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 581 KW - Bombyx mori silk KW - gold KW - photocatalytic water splitting KW - titania Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-423499 SN - 1866-8372 IS - 581 ER - TY - THES A1 - Schulze, Nicole T1 - Neue Templatphasen zur anisotropen Goldnanopartikelherstellung durch den Einsatz strukturbildender Polymere T1 - New template phases for anisotropic gold nanoparticle production through the use of structure-forming polymers N2 - Ziel der vorliegenden Arbeit war die Synthese und Charakterisierung von anisotropen Goldnanopartikeln in einer geeigneten Polyelektrolyt-modifizierten Templatphase. Der Mittelpunkt bildet dabei die Auswahl einer geeigneten Templatphase, zur Synthese von einheitlichen und reproduzierbaren anisotropen Goldnanopartikeln mit den daraus resultierenden besonderen Eigenschaften. Bei der Synthese der anisotropen Goldnanopartikeln lag der Fokus in der Verwendung von Vesikeln als Templatphase, wobei hier der Einfluss unterschiedlicher strukturbildender Polymere (stark alternierende Maleamid-Copolymere PalH, PalPh, PalPhCarb und PalPhBisCarb mit verschiedener Konformation) und Tenside (SDS, AOT – anionische Tenside) bei verschiedenen Synthese- und Abtrennungsbedingungen untersucht werden sollte. Im ersten Teil der Arbeit konnte gezeigt werden, dass PalPhBisCarb bei einem pH-Wert von 9 die Bedingungen eines Röhrenbildners für eine morphologische Transformation von einer vesikulären Phase in eine röhrenförmige Netzwerkstruktur erfüllt und somit als Templatphase zur formgesteuerten Bildung von Nanopartikeln genutzt werden kann. Im zweiten Teil der Arbeit wurde dargelegt, dass die Templatphase PalPhBisCarb (pH-Wert von 9, Konzentration von 0,01 wt.%) mit AOT als Tensid und PL90G als Phospholipid (im Verhältnis 1:1) die effektivste Wahl einer Templatphase für die Bildung von anisotropen Strukturen in einem einstufigen Prozess darstellt. Bei einer konstanten Synthesetemperatur von 45 °C wurden die besten Ergebnisse bei einer Goldchloridkonzentration von 2 mM, einem Gold-Templat-Verhältnis von 3:1 und einer Synthesezeit von 30 Minuten erzielt. Ausbeute an anisotropen Strukturen lag bei 52 % (Anteil an dreieckigen Nanoplättchen von 19 %). Durch Erhöhung der Synthesetemperatur konnte die Ausbeute auf 56 % (29 %) erhöht werden. Im dritten Teil konnte durch zeitabhängige Untersuchungen gezeigt werden, dass bei Vorhandensein von PalPhBisCarb die Bildung der energetisch nicht bevorzugten Plättchen-Strukturen bei Raumtemperatur initiiert wird und bei 45 °C ein Optimum annimmt. Kintetische Untersuchungen haben gezeigt, dass die Bildung dreieckiger Nanoplättchen bei schrittweiser Zugabe der Goldchlorid-Präkursorlösung zur PalPhBisCarb enthaltenden Templatphase durch die Dosierrate der vesikulären Templatphase gesteuert werden kann. In umgekehrter Weise findet bei Zugabe der Templatphase zur Goldchlorid-Präkursorlösung bei 45 °C ein ähnlicher, kinetisch gesteuerter Prozess der Bildung von Nanodreiecken statt mit einer maximalen Ausbeute dreieckigen Nanoplättchen von 29 %. Im letzten Kapitel erfolgten erste Versuche zur Abtrennung dreieckiger Nanoplättchen von den übrigen Geometrien der gemischten Nanopartikellösung mittels tensidinduzierter Verarmungsfällung. Bei Verwendung von AOT mit einer Konzentration von 0,015 M wurde eine Ausbeute an Nanoplättchen von 99 %, wovon 72 % dreieckiger Geometrien hatten, erreicht. N2 - The aim of the present work was the synthesis and characterization of anisotropic gold nanoparticles in a suitable polyelectrolyte-modified template phase. The focus was on the selection of a suitable template phase for the synthesis of uniform and reproducible anisotropic gold nanoparticles with the resulting special properties. In the synthesis of the anisotropic gold nanoparticles, the focus was on the use of vesicles as a template phase. Here, the influence of different structure-forming polymers (strongly alternating maleimide copolymers PalH, PalPh, PalPhCarb and PalPhBisCarb with different conformations) and surfactants (SDS, AOT - anionic surfactants) should be studied at various synthesis and separation conditions. In the first part of the work, it could be shown that PalPhBisCarb at pH 9 meets the requirements of a tubulating agent for a morphological transformation of a vesicular phase into a tubular network structure and thus can be used as a template phase for the shape-controlled formation of nanoparticles. In the second part of the work, it was shown that the template phase PalPhBisCarb (pH value of 9, concentration of 0.01 wt.%) with AOT as surfactant and PL90G as phospholipid (in the ratio 1:1) is the most effective choice of template phase for the formation of anisotropic structures in a one-step process. At a constant synthesis temperature of 45 °C, the best results were achieved with a gold chloride concentration of 2 mM, a gold-template ratio of 3:1 and a synthesis time of 30 minutes. The yield of anisotropic structures was 52% (triangular nanoplatelet content of 19%). By increasing the synthesis temperature, the yield could be increased to 56% (29%). In the third part, it was shown by time-dependent investigations that in the presence of PalPhBisCarb, the formation of the not energetically preferred platelet structures is initiated at room temperature and assumes an optimum at 45 °C. Kinetical studies have shown that the formation of triangular nanosheets can be controlled by the dosing rate of the vesicular template phase when the gold chloride precursor solution is gradually added to the PalPhBisCarb-containing template phase. Conversely, upon addition of the template phase to the gold chloride precursor solution at 45 °C, a similar, kinetically controlled process of formation of nanodimers takes place with a maximum yield of triangular nanoplatelets of 29%. In the last chapter, initial attempts were made to separate triangular nanoplatelets from the other geometries of the mixed nanoparticle solution by means of surfactant-induced depletion flocculation. When AOT was used at a concentration of 0.015 M, a yield of nanoplatelets of 99%, of which 72% had triangular geometries, was achieved. KW - Nanopartikel KW - nanoparticle KW - Templatphase KW - template phase KW - Gold KW - gold KW - anisotrop KW - anisotropic Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-409515 ER - TY - THES A1 - Krüger, Stefanie T1 - Seidenbasierte anorganische Funktionsmaterialien T1 - Silk based inorganic functional materials N2 - In der vorliegenden Arbeit konnten erfolgreich zwei unterschiedliche Hybridmaterialien (HM) über die Sol-Gel-Methode synthetisiert werden. Bei den HM handelt es sich um Monolithe mit einem Durchmesser von bis zu 4,5 cm. Das erste HM besteht aus Titandioxid und Bombyx mori Seide und wird als TS bezeichnet, während das zweite weniger Seide und zusätzlich Polyethylenoxid (PEO) enthält und daher als TPS abgekürzt wird. Einige der HM wurden nach der Synthese in eine wässrige Tetrachloridogoldsäure-Lösung getaucht, wodurch sich auf der Oberfläche Goldnanopartikel gebildet haben. Die Materialien wurden mittels Elektronenmikroskopie, energiedispersiver Röntgenspektroskopie, Ramanspektroskopie sowie Röntgenpulverdiffraktometrie charakterisiert. Die Ergebnisse zeigen, dass beide HM aus etwa 5 nm großen, sphärischen Titandioxidnanopartikeln aufgebaut sind, die primär aus Anatas und zu einem geringen Anteil aus Brookit bestehen. Die Goldnanopartikel bei TPS_Au waren größer und polydisperser als die Goldnanopartikel auf dem TS_Au HM. Darüber hinaus sind die Goldnanopartikel im TS HM tiefer in das Material eingedrungen als beim TPS HM. Die weiterführende Analyse der HM mittels Elementaranalyse und thermogravimetrischer Analyse ergab für TPS einen geringeren Anteil an organischen Bestandteilen im HM als für TS, obwohl für beide Synthesen die gleiche Masse an organischen Materialien eingesetzt wurde. Es wird vermutet, dass das PEO während der Synthese teilweise wieder aus dem Material herausgewaschen wird. Diese Theorie korreliert mit den Ergebnissen aus der Stickstoffsorption und der Quecksilberporosimetrie, die für das TPS HM eine höhere Oberfläche als für das TS HM anzeigten. Die Variation einiger Syntheseparameter wie die Menge an Seide und PEO oder die Zusammensetzung der Titandioxidvorläuferlösung hatte einen großen Einfluss auf die synthetisierten HM. Während unterschiedliche Mengen an PEO die Größe des HM beeinflussten, konnte ohne Seide kein HM in einer ähnlichen Größe hergestellt werden. Die Bildung der HM wird stark von der Zusammensetzung der Titandioxidvorläuferlösung beeinflusst. Eine Veränderung führte daher nur selten zur Bildung eines homogenen HM. Die in dieser Arbeit synthetisierten HM wurden als Photokatalysatoren für die Wasserspaltung und den Abbau von Methylenblau eingesetzt. Bei der photokatalytischen Wasserspaltung wurde zunächst der Einfluss unterschiedlicher Goldkonzentrationen beim TPS HM auf die Wasserstoffausbeute untersucht. Die besten Ergebnisse wurden bei einer Menge von 2,5 mg Tetrachloridogoldsäure erhalten. Darüber hinaus wurde gezeigt, dass mit dem TPS HM eine deutlich höhere Menge an Wasserstoff gewonnen werden konnte als mit dem TS HM. Die Ursachen für die schlechtere Aktivität werden in der geringeren spezifischen Oberfläche, der unterschiedlichen Porenstruktur, dem höheren Anteil an Seide und besonders in der geringeren Größe und höheren Eindringtiefe der Goldnanopartikel vermutet. Darüber hinaus konnte mit einem höheren UV-Anteil in der Lichtquelle sowie durch die Zugabe von Ethanol als Opferreagenz eine Zunahme der Wasserstoffausbeute erzielt werden. Bei dem Methylenblauabbau wurde für beide HM zunächst nur eine Adsorption des Methylenblaus beobachtet. Nach der Zugabe von Wasserstoffperoxid konnte nach 8 h bereits eine fast vollständige Oxidation des Methylenblaus unter sichtbarem Licht beobachtet werden. Die Ursache für die etwas höhere Aktivität von TPS gegenüber TS wird in der unterschiedlichen Porenstruktur und dem höheren Anteil an Seide im TS HM vermutet. Insgesamt zeigen beide HM eine gute photokatalytische Aktivität für den Abbau von Methylenblau im Vergleich zu den erhaltenen Werten aus der Literatur. N2 - Two different hybrid materials (HM) were successfully synthesized by the sol-gel-method. The first HM is based on titania and Bombyx mori silk and will be denoted as TS. The second HM is TPS and also contains titania but a lower amount of silk and additionally poly(ethylene oxide) (PEO). Furthermore some of the HM were immerse in aqueous hydrogen tetrachloroaurate solutions to deposit gold nanoparticles (AuNP) on the surface of the HM. All materials are monoliths with diameters of up to ca. 4.5 cm. Analysis via electron microscopy, energy dispersive X-ray spectroscopy, Raman spectroscopy, and X-ray powder diffraction shows that the HM are based on 5 nm titania nanoparticles (TNP) – mainly anatase with a minor fraction of brookite - and AuNPs on the order of 7-18 nm. Addition of PEO to the reaction mixture enables pore size tuning which were analyzed by nitrogen sorption and mercury intrusion porosimetry measurements. These observations correlate with the results from elemental and thermogravimetric analysis which show a lower amount of organic components in TPS than in TS HM. In both HM the amount of organic components used for the synthesis are the same. Therefore we suppose that PEO is washed out of the material during the synthesis which yield to a higher surface area and a lower amount of organic components. A further chapter of the thesis describes the variation of different synthesis parameter like amount of silk or PEO or the composition of the titania precursor solution. The results show that it is impossible to create a HM of about 4.5 cm without silk. Furthermore the amount of PEO influences the size of the HM whereas the composition of the titania precursor solution has a large effect on the synthesis of such HM. Furthermore both HM were tested for their photocatalytic activities for water splitting and methylene blue (MB) degradation. Water splitting experiments using a sun simulator show that the new hybrid materials are effective water splitting catalysts and produce up to 30 mmol of hydrogen per 24 h. The amount of produced hydrogen is dependent on the HM (TPS_Au or TS_Au), the amount of AuNP, the addition of ethanol as sacrificial reagent or the light source. Studies of MB degradation show initially just an adsorption and not a degradation of MB. After the addition of hydrogen peroxide, there is an almost complete degradation of MB within 8 h. Both HM show a good photocatalytic activity for MB degradation compared with results from the literature. KW - photocatalytic water splitting KW - titania KW - Bombyx mori silk KW - gold KW - photokatalytische Wasserspaltung KW - Titandioxid KW - Gold KW - Bombyx mori Seide Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-404635 ER - TY - JOUR A1 - Wu, Lei A1 - Glebe, Ulrich A1 - Böker, Alexander T1 - Fabrication of Thermoresponsive Plasmonic Core-Satellite Nanoassemblies with a Tunable Stoichiometry via Surface-Initiated Reversible Addition-Fragmentation Chain Transfer Polymerization from Silica Nanoparticles JF - Advanced materials interfaces N2 - This work presents a fabrication of thermoresponsive plasmonic core-satellite nanoassemblies. The structure has a silica nanoparticle core surrounded by gold nanoparticle satellites using thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) chains as scaffolds. The thiol-terminated PNIPAM shell is densely grafted on the silica core via surface-initiated reversible addition-fragmentation chain transfer polymerization and used to anchor numerous gold nanoparticle satellites with a tunable stoichiometry. Below and above lower critical solution temperature, the chain conformation of PNIPAM reversibly changes between swollen and shrunken state. The reversible change of the polymer size varies the refractive index of the local medium surrounding the satellites and the distance between them. The two effects together lead to the thermoresponsive plasmonic properties of the nanoassemblies. Under different satellite densities, two distinctive plasmonic features appear. KW - gold KW - hybrid materials KW - polymeric materials KW - silica KW - surface plasmon resonance Y1 - 2017 U6 - https://doi.org/10.1002/admi.201700092 SN - 2196-7350 VL - 4 PB - Wiley CY - Hoboken ER - TY - JOUR A1 - Fandrich, Artur A1 - Buller, Jens A1 - Schäfer, Daniel A1 - Wischerhoff, Erik A1 - Laschewsky, André A1 - Lisdat, Fred T1 - Electrochemical characterization of a responsive macromolecular interface on gold JF - Physica status solidi : A, Applications and materials science N2 - This study reports on the investigation of a thermoresponsive polymer as a thin film on electrodes and the influence of coupling a peptide and an antibody to the film. The utilized polymer from the class of poly(oligoethylene glycol)-methacrylate polymers (poly(OEGMA)) with carboxy functions containing side chains was synthesized and properly characterized in aqueous solutions. The dependence of the cloud point on the pH of the surrounding media is discussed. The responsive polymer was immobilized on gold electrodes as shown by electrochemical, quartz crystal microbalance (QCM), and atomic force microscopy (AFM) techniques. The temperature dependent behavior of the polymer covalently grafted to gold substrates is investigated using cyclic voltammetry (CV) in ferro-/ferricyanide solution. Significant changes in the slope of the temperature-dependence of the voltammetric peak current and the peak separation values clearly indicate the thermally induced conformational change on the surface. Finally, a biorecognition reaction between a short FLAG peptide (N-Asp-Tyr-Lys-Asp-Asp-Asp-Asp-Lys-C) covalently immobilized on the polymer interface and the corresponding IgG antibody was performed. The study shows that the responsiveness of the electrode is retained after peptide coupling and antibody binding, although the response is diminished. KW - biorecognition reactions KW - cyclic voltammetry KW - electrodes KW - gold KW - interfaces KW - responsive polymers Y1 - 2015 U6 - https://doi.org/10.1002/pssa.201431698 SN - 1862-6300 SN - 1862-6319 VL - 212 IS - 6 SP - 1359 EP - 1367 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Cui, Qianling A1 - Shen, Guizhi A1 - Yan, Xuehai A1 - Li, Lidong A1 - Moehwald, Helmuth A1 - Bargheer, Matias T1 - Fabrication of Au@Pt multibranched nanoparticles and their application to in situ SERS monitoring JF - ACS applied materials & interfaces N2 - Here, we present an Au@Pt core-shell multibranched nanoparticle as a new substrate capable of in situ surface-enhanced Raman scattering (SERS), thereby enabling monitoring of the catalytic reaction on the active surface. By careful control of the amount of Pt deposited bimetallic Au@Pt, nanoparticles with moderate performance both for SERS and catalytic activity were obtained. The Pt-catalyzed reduction of 4-nitrothiophenol by borohydride was chosen as the model reaction. The intermediate during the reaction was captured and clearly identified via SERS spectroscopy. We established in situ SERS spectroscopy as a promising and powerful technique to investigate in situ reactions taking place in heterogeneous catalysis. KW - nanoparticles KW - gold KW - core-shell nanostructure KW - surface-enhanced Raman scattering KW - heterogeneous catalysis KW - bimetallic nanoparticles Y1 - 2014 U6 - https://doi.org/10.1021/am504709a SN - 1944-8244 VL - 6 IS - 19 SP - 17075 EP - 17081 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Cui, Qianling A1 - Yashchenok, Alexey A1 - Zhang, Lu A1 - Li, Lidong A1 - Masic, Admir A1 - Wienskol, Gabriele A1 - Moehwald, Helmuth A1 - Bargheer, Matias T1 - Fabrication of Bifunctional Gold/Gelatin Hybrid Nanocomposites and Their Application JF - ACS applied materials & interfaces N2 - Herein, a facile method is presented to integrate large gold nanoflowers (similar to 80 nm) and small gold nanoparticles (2-4 nm) into a single entity, exhibiting both surface-enhanced Raman scattering (SERS) and catalytic activity. The as-prepared gold nanoflowers were coated by a gelatin layer, in which the gold precursor was adsorbed and in situ reduced into small gold nanoparticles. The thickness of the gelatin shell is controlled to less than 10 nm, ensuring that the small gold nanoparticles are still in a SERS-active range of the inner Au core. Therefore, the reaction catalyzed by these nanocomposites can be monitored in situ using label-free SERS spectroscopy. In addition, these bifunctional nanocomposites are also attractive candidates for application in SERS monitoring of bioreactions because of their excellent biocompatibility. KW - core-shell nanostructure KW - gold KW - hybrid material KW - gelatin KW - nanoparticles KW - surface-enhanced Raman scattering Y1 - 2014 U6 - https://doi.org/10.1021/am5000068 SN - 1944-8244 VL - 6 IS - 3 SP - 1999 EP - 2002 PB - American Chemical Society CY - Washington ER -