TY - GEN A1 - Schulze, Patricia S. C. A1 - Bett, Alexander J. A1 - Bivour, Martin A1 - Caprioglio, Pietro A1 - Gerspacher, Fabian M. A1 - Kabaklı, Özde Ş. A1 - Richter, Armin A1 - Stolterfoht, Martin A1 - Zhang, Qinxin A1 - Neher, Dieter A1 - Hermle, Martin A1 - Hillebrecht, Harald A1 - Glunz, Stefan W. A1 - Goldschmidt, Jan Christoph T1 - 25.1% high-efficiency monolithic perovskite silicon tandem solar cell with a high bandgap perovskite absorber T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Monolithic perovskite silicon tandem solar cells can overcome the theoretical efficiency limit of silicon solar cells. This requires an optimum bandgap, high quantum efficiency, and high stability of the perovskite. Herein, a silicon heterojunction bottom cell is combined with a perovskite top cell, with an optimum bandgap of 1.68 eV in planar p-i-n tandem configuration. A methylammonium-free FA(0.75)Cs(0.25)Pb(I0.8Br0.2)(3) perovskite with high Cs content is investigated for improved stability. A 10% molarity increase to 1.1 m of the perovskite precursor solution results in approximate to 75 nm thicker absorber layers and 0.7 mA cm(-2) higher short-circuit current density. With the optimized absorber, tandem devices reach a high fill factor of 80% and up to 25.1% certified efficiency. The unencapsulated tandem device shows an efficiency improvement of 2.3% (absolute) over 5 months, showing the robustness of the absorber against degradation. Moreover, a photoluminescence quantum yield analysis reveals that with adapted charge transport materials and surface passivation, along with improved antireflection measures, the high bandgap perovskite absorber has the potential for 30% tandem efficiency in the near future. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1197 KW - heterojunction silicon solar cells KW - interfaces KW - perovskite solar cells KW - tandem solar cells KW - thin films Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-525668 SN - 1866-8372 IS - 7 ER - TY - JOUR A1 - Schulze, Patricia S. C. A1 - Bett, Alexander J. A1 - Bivour, Martin A1 - Caprioglio, Pietro A1 - Gerspacher, Fabian M. A1 - Kabaklı, Özde Ş. A1 - Richter, Armin A1 - Stolterfoht, Martin A1 - Zhang, Qinxin A1 - Neher, Dieter A1 - Hermle, Martin A1 - Hillebrecht, Harald A1 - Glunz, Stefan W. A1 - Goldschmidt, Jan Christoph T1 - 25.1% high-efficiency monolithic perovskite silicon tandem solar cell with a high bandgap perovskite absorber JF - Solar RRL N2 - Monolithic perovskite silicon tandem solar cells can overcome the theoretical efficiency limit of silicon solar cells. This requires an optimum bandgap, high quantum efficiency, and high stability of the perovskite. Herein, a silicon heterojunction bottom cell is combined with a perovskite top cell, with an optimum bandgap of 1.68 eV in planar p-i-n tandem configuration. A methylammonium-free FA(0.75)Cs(0.25)Pb(I0.8Br0.2)(3) perovskite with high Cs content is investigated for improved stability. A 10% molarity increase to 1.1 m of the perovskite precursor solution results in approximate to 75 nm thicker absorber layers and 0.7 mA cm(-2) higher short-circuit current density. With the optimized absorber, tandem devices reach a high fill factor of 80% and up to 25.1% certified efficiency. The unencapsulated tandem device shows an efficiency improvement of 2.3% (absolute) over 5 months, showing the robustness of the absorber against degradation. Moreover, a photoluminescence quantum yield analysis reveals that with adapted charge transport materials and surface passivation, along with improved antireflection measures, the high bandgap perovskite absorber has the potential for 30% tandem efficiency in the near future. KW - heterojunction silicon solar cells KW - interfaces KW - perovskite solar cells KW - tandem solar cells KW - thin films Y1 - 2020 VL - 4 IS - 7 PB - John Wiley & Sons, Inc. CY - New Jersey ER - TY - THES A1 - Jung, Carl Christoph T1 - Lichtinduzierte Generierung und Charakterisierung optischer Anisotropie N2 - Eine Nutzung der optischen Anisotropie dünner Schichten ist vor allem für die Displaytechnologie, die optische Datenspeicherung und für optische Sicherheitselemente von hoher Bedeutung. Diese Doktorarbeit befasst sich mit theoretischen und experimentellen Untersuchung von dreidimensionaler Anisotropie und dabei insbesondere mit der Untersuchung von lichtinduzierter dreidimensionaler Anisotropie in organischen dünnen Polymer-Schichten. Die gewonnenen Erkentnisse und entwickelten Methoden können wertvolle Beiträge für Optimierungsprozesse, wie bei der Kompensation der Blickwinkelabhängigkeit von Flüssigkristall-Displays, liefern. Die neue Methode der Immersions-Transmissions-Ellipsometrie (ITE) zur Untersuchung von dünneren Schichten wurde im Rahmen dieser Dissertation entwickelt. Diese Methode gestattet es, in Kombination mit konventioneller Reflexions- und Transmissionsellipsometrie, die absoluten dreidimensionalen Brechungsindices einer biaxialen Schicht zu bestimmen. Erstmals gelang es damit, das dreidimensionale Brechungsindexellipsoid von transparenten, dünneren (150 nm) Filmen hochgenau (drei Stellen hinter dem Komma) zu bestimmen. Die ITE-Methode hat demzufolge das Potential, auch bei noch dünneren Schichten mit Gewinn eingesetzt werden zu können. Die lichtinduzierte Generierung von dreidimensionaler Anisotropie wurde in dünnen Schichten von azobenzenhaltigen und zimtsäurehaltigen, amorphen und flüssig-kristallinen Homo- und Copolymeren untersucht. Erstmals wurden quantitative Untersuchungen zur Änderung von lichtinduzierten, dreidimensionalen Anisotropien in dünnen Schichten von azobenzenhaltigen und zimtsäurehaltigen Polymeren bei Tempern oberhalb der Glastemperatur durchgeführt. Bei vielen der untersuchten Polymere war die dreidimensionale Ordnung nach dem Bestrahlen mit polarisiertem Licht und anschließendem Tempern oberhalb der Glastemperatur scheinbar von der Schichtdicke abhängig. Die Ursache liegt wohl in der, mit der neuentwickelten ITE-Methode detektierten, planaren Ausgangsorientierung der aufgeschleuderten dünneren Schichten. Um Verkippungs-Gradienten in dickeren Polymerschichten in ihrem Verlauf zu bestimmen, wurde eine spezielle Methode unter Benutzung der Wellenleitermoden-Spektroskopie entwickelt. Quantenchemisch bestimmte, maximal induzierbare Doppelbrechungen in flüssig-kristallinen Polymeren wurden mit den experimentell gefundenen Ordnungen verglichen. N2 - The optical anisotropy of thin films is of great interest mainly in the display technology, the optical data storage and for optical security elements. The topic of this thesis was the theoretical and experimental investigation of three-dimensional anisotropy and especially the investigation of light-induced three-dimensional anisotropy in thin organic polymer films. The results and newly developed methods can contribute significantly to technical optimisation processes, e. g. for the compensation of the viewing angle dependence of liquid crystal displays. The new method of immersion-transmission-ellipsometry (ITE) for the investigation of thinner layers was developed in the course of this PhD. The new method allows to determine the absolute three-dimensional refractive indices of a biaxial film. For the first time it has been possible to determine the three-dimensional indicatrix of transparent, 150 nm thin films with an accuracy of three digits after the decimal point. The ITE-method therefore has the potential to be used for the investigation of even thinner films. The light-induced generation of three-dimensional anisotropy was investigated in thin films of azobenzene-containing and cinnamate containing, amorphous and liquid crystalline homo- and copolymers. For the first time, quantitative investigations of the changes of light-induced, three-dimensional anisotropies in thin films of azobenzene containing and cinnamate containing polymers, that were brought about by annealing above the glass transition temperatures, were carried out. For many of the investigated polymers the three-dimensional order after irradiation with polarised light and subsequent annealing above the glass transition temperature seemed to be dependent on the film thickness. The reason could be the planar initial order of the spin-coated thinner films, which was detected with the new ITE-method. For the characterisation of tilt gradients in thicker polymer films a special method using waveguide spectroscopy was developed. Quantum chemically determined maximal values of inducible birefringence were compared with the experimentally determined values. KW - Anisotropie KW - Photoorientierung KW - Photoalignment KW - dünne Schichten KW - 3D KW - Ellipsometrie KW - Kompensatoren KW - Wellenleiter KW - Displays KW - Fluoreszenz KW - anisotropy KW - photo-orientation KW - photoalignment KW - thin films KW - 3D KW - ellipsometry KW - compensation films KW - waveguides KW - displays KW - fluorescence Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0001390 ER - TY - BOOK A1 - Jung, Carl Christoph T1 - Lichtinduzierte Generierung und Charakterisierung optischer Anisotropie. - [überarb. Diss.] N2 - Eine Nutzung der optischen Anisotropie dünner Schichten ist vor allem für die Displaytechnologie, die optische Datenspeicherung und für optische Sicherheitselemente von hoher Bedeutung. Diese Doktorarbeit befasst sich mit theoretischen und experimentellen Untersuchung von dreidimensionaler Anisotropie und dabei insbesondere mit der Untersuchung von lichtinduzierter dreidimensionaler Anisotropie in organischen dünnen Polymer-Schichten. Die gewonnenen Erkentnisse und entwickelten Methoden können wertvolle Beiträge für Optimierungsprozesse, wie bei der Kompensation der Blickwinkelabhängigkeit von Flüssigkristall-Displays, liefern. Die neue Methode der Immersions-Transmissions-Ellipsometrie (ITE) zur Untersuchung von dünneren Schichten wurde im Rahmen dieser Dissertation entwickelt. Diese Methode gestattet es, in Kombination mit konventioneller Reflexions- und Transmissionsellipsometrie, die absoluten dreidimensionalen Brechungsindices einer biaxialen Schicht zu bestimmen. Erstmals gelang es damit, das dreidimensionale Brechungsindexellipsoid von transparenten, dünneren (150 nm) Filmen hochgenau (drei Stellen hinter dem Komma) zu bestimmen. Die ITE-Methode hat demzufolge das Potential, auch bei noch dünneren Schichten mit Gewinn eingesetzt werden zu können. Die lichtinduzierte Generierung von dreidimensionaler Anisotropie wurde in dünnen Schichten von azobenzenhaltigen und zimtsäurehaltigen, amorphen und flüssig-kristallinen Homo- und Copolymeren untersucht. Erstmals wurden quantitative Untersuchungen zur Änderung von lichtinduzierten, dreidimensionalen Anisotropien in dünnen Schichten von azobenzenhaltigen und zimtsäurehaltigen Polymeren bei Tempern oberhalb der Glastemperatur durchgeführt. Bei vielen der untersuchten Polymere war die dreidimensionale Ordnung nach dem Bestrahlen mit polarisiertem Licht und anschließendem Tempern oberhalb der Glastemperatur scheinbar von der Schichtdicke abhängig. Die Ursache liegt wohl in der, mit der neuentwickelten ITE-Methode detektierten, planaren Ausgangsorientierung der aufgeschleuderten dünneren Schichten. Um Verkippungs-Gradienten in dickeren Polymerschichten in ihrem Verlauf zu bestimmen, wurde eine spezielle Methode unter Benutzung der Wellenleitermoden-Spektroskopie entwickelt. Quantenchemisch bestimmte, maximal induzierbare Doppelbrechungen in flüssig-kristallinen Polymeren wurden mit den experimentell gefundenen Ordnungen verglichen. N2 - The optical anisotropy of thin films is of great interest mainly in the display technology, the optical data storage and for optical security elements. The topic of this thesis was the theoretical and experimental investigation of three-dimensional anisotropy and especially the investigation of light-induced three-dimensional anisotropy in thin organic polymer films. The results and newly developed methods can contribute significantly to technical optimisation processes, e. g. for the compensation of the viewing angle dependence of liquid crystal displays. The new method of immersion-transmission-ellipsometry (ITE) for the investigation of thinner layers was developed in the course of this PhD. The new method allows to determine the absolute three-dimensional refractive indices of a biaxial film. For the first time it has been possible to determine the three-dimensional indicatrix of transparent, 150 nm thin films with an accuracy of three digits after the decimal point. The ITE-method therefore has the potential to be used for the investigation of even thinner films. The light-induced generation of three-dimensional anisotropy was investigated in thin films of azobenzene-containing and cinnamate containing, amorphous and liquid crystalline homo- and copolymers. For the first time, quantitative investigations of the changes of light-induced, three-dimensional anisotropies in thin films of azobenzene containing and cinnamate containing polymers, that were brought about by annealing above the glass transition temperatures, were carried out. For many of the investigated polymers the three-dimensional order after irradiation with polarised light and subsequent annealing above the glass transition temperature seemed to be dependent on the film thickness. The reason could be the planar initial order of the spin-coated thinner films, which was detected with the new ITE-method. For the characterisation of tilt gradients in thicker polymer films a special method using waveguide spectroscopy was developed. Quantum chemically determined maximal values of inducible birefringence were compared with the experimentally determined values. KW - Anisotropie KW - Photoorientierung KW - Photoalignment KW - dünne Schichten KW - 3D KW - Ellipsometrie KW - Kompensatoren KW - Wellenleiter KW - Displays KW - Fluoreszenz KW - anisotropy KW - photo-orientation KW - photoalignment KW - thin films KW - 3D KW - ellipsometry KW - compensation films KW - waveguides KW - displays KW - fluorescence Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0001501 ER - TY - THES A1 - Zeuschner, Steffen Peer T1 - Magnetoacoustics observed with ultrafast x-ray diffraction N2 - In the present thesis I investigate the lattice dynamics of thin film hetero structures of magnetically ordered materials upon femtosecond laser excitation as a probing and manipulation scheme for the spin system. The quantitative assessment of laser induced thermal dynamics as well as generated picosecond acoustic pulses and their respective impact on the magnetization dynamics of thin films is a challenging endeavor. All the more, the development and implementation of effective experimental tools and comprehensive models are paramount to propel future academic and technological progress. In all experiments in the scope of this cumulative dissertation, I examine the crystal lattice of nanoscale thin films upon the excitation with femtosecond laser pulses. The relative change of the lattice constant due to thermal expansion or picosecond strain pulses is directly monitored by an ultrafast X-ray diffraction (UXRD) setup with a femtosecond laser-driven plasma X-ray source (PXS). Phonons and spins alike exert stress on the lattice, which responds according to the elastic properties of the material, rendering the lattice a versatile sensor for all sorts of ultrafast interactions. On the one hand, I investigate materials with strong magneto-elastic properties; The highly magnetostrictive rare-earth compound TbFe2, elemental Dysprosium or the technological relevant Invar material FePt. On the other hand I conduct a comprehensive study on the lattice dynamics of Bi1Y2Fe5O12 (Bi:YIG), which exhibits high-frequency coherent spin dynamics upon femtosecond laser excitation according to the literature. Higher order standing spinwaves (SSWs) are triggered by coherent and incoherent motion of atoms, in other words phonons, which I quantified with UXRD. We are able to unite the experimental observations of the lattice and magnetization dynamics qualitatively and quantitatively. This is done with a combination of multi-temperature, elastic, magneto-elastic, anisotropy and micro-magnetic modeling. The collective data from UXRD, to probe the lattice, and time-resolved magneto-optical Kerr effect (tr-MOKE) measurements, to monitor the magnetization, were previously collected at different experimental setups. To improve the precision of the quantitative assessment of lattice and magnetization dynamics alike, our group implemented a combination of UXRD and tr-MOKE in a singular experimental setup, which is to my knowledge, the first of its kind. I helped with the conception and commissioning of this novel experimental station, which allows the simultaneous observation of lattice and magnetization dynamics on an ultrafast timescale under identical excitation conditions. Furthermore, I developed a new X-ray diffraction measurement routine which significantly reduces the measurement time of UXRD experiments by up to an order of magnitude. It is called reciprocal space slicing (RSS) and utilizes an area detector to monitor the angular motion of X-ray diffraction peaks, which is associated with lattice constant changes, without a time-consuming scan of the diffraction angles with the goniometer. RSS is particularly useful for ultrafast diffraction experiments, since measurement time at large scale facilities like synchrotrons and free electron lasers is a scarce and expensive resource. However, RSS is not limited to ultrafast experiments and can even be extended to other diffraction techniques with neutrons or electrons. N2 - In der vorliegenden Arbeit untersuche ich die Gitterdynamik von magnetisch geordneten und dünnen Filmen, deren Spinsystem mit Femtosekunden-Laserpulsen angeregt und untersucht wird. Die Quantifizierung der laserinduzierten thermischen Dynamik, der erzeugten Pikosekunden-Schallpulse sowie deren jeweiliger Einfluss auf die Magnetisierungsdynamik ist ein schwieriges Unterfangen. Umso mehr ist die Entwicklung und Anwendung von effizienten experimentellen Konzepten und umfangreichen Modellen grundlegend für das Antreiben des zukünftigen wissenschaftlichen und technologischen Fortschritt. In jedem Experiment dieser kummulativen Dissertation untersuche ich das Kristallgitter von Nanometer dünnen Filmen nach der Anregung mit Femtosekunden-Laserpulsen. Die relative Änderung der Gitterkonstante, hervorgerufen durch thermische Ausdehnung oder Pikosekunden-Schallpulse, wird dabei direkt mittels ultraschneller Röntgenbeugung (UXRD) gemessen. Der Aufbau nutzt zur Bereitstellung von ultrakurzen Röntgenpulsen eine lasergetriebene Plasma-Röntgenquelle (PXS). Phononen und Spins üben gleichermaßen einen Druck auf das Gitter aus, welches entsprechend der elastsischen Eigenschaften des Materials reagiert, was das Gitter zu einem vielseitigen Sensor für ultraschenlle Wechselwirkungen macht. Zum einen untersuche ich Materialien mit starken magnetoelastischen Eigentschaften: die stark magnetostriktive Seltenen-Erden-Verbindung TbFe2, elementares Dysprosium oder das technologisch relavante Invar-Material FePt. Zum anderen habe ich eine umfangreiche Studie der Gitterdynamik von Bi1Y2Fe5O12 (Bi:YIG) angestellt, in dem der Literatur zufolge hochfrequente kohärente Spindynamiken durch Femtosekunden-Laseranregung zu beobachten sind. Diese stehenden Spinwellen (SSWs) höherer Ordnung entstehen durch die kohärente und inkohärente Bewegung von Atomen, in anderen Worten Phononen, welche ich durch UXRD vermessen habe. Somit sind wir in der Lage, die experimentellen Beobachtungen der Gitter- und Spindynamik qualitativ und quantitativ zu vereinigen. Dies geschieht durch eine Kombination von Viel-Temperatur- und Anisotropiemodellierung sowie elastische, magnetoelastische, und mikromagnetsiche Modelle. Die gemeinsamen Daten von UXRD und der zeitaufgelösten magnetooptischen Kerr-Effekt Messungen (tr-MOKE), um jeweils die Gitter- und Spindynamik zu messen, wurden in der Vergangenheit noch an unterschiedlichen experimentellen Aufbauten gemessen. Um die Quantifizierung präziser zu gestalten, haben wir in unserer Arbeitsgruppe UXRD und tr-MOKE in einem einzigen Aufbau kombiniert, welcher somit meines Wissens der erste seiner Art ist. Ich half bei dem Entwurf und der Inbetriebnahme des neuen Aufbaus, welcher die gleichzeitige Messung von Gitter- und Spindynamik auf einer ultraschnellen Zeitskala unter identischen Anregungsbedingungen ermöglicht. Außerdem entwickelte ich eine neue Messroutine für Röntgenbeugung, welche die Messzeit von UXRD-Experimenten um bis zu einer Größenordnungen reduziert. Es nennt sich das Schneiden des reziproken Raumes (reciprocal space slicing, RSS) und nutzt den Vorteil von Flächendetektoren die Bewegung von Beugungsreflexen zu detektieren, was von einer Änderung der Gitterkonstante einhergeht, ohne zeitintensive Scans der Beugungswinkel mit dem Goniometer durchzuführen. RSS ist besonders nützlich für ultraschnelle Beugungsexperimente, weil die Messzeit an Großgeräten wie Synchrotrons oder Freie Elektronen Laser eine seltene und teure Ressource ist. Darüber hinaus ist RSS nicht zwangsläufig auf die Anwendung in ultraschnellen Experimenten beschränkt und kann sogar auf andere Beugungsexperimente, wie die mit Neutronen und Elektronen, ausgeweitet werden. KW - ultrafast KW - X-ray diffraction KW - thin films KW - magnetoelasticity KW - ultraschnell KW - Röntgenbeugung KW - dünne Filme KW - Magnetoelastizität Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-561098 ER - TY - JOUR A1 - Caprioglio, Pietro A1 - Stolterfoht, Martin A1 - Wolff, Christian Michael A1 - Unold, Thomas A1 - Rech, Bernd A1 - Albrecht, Steve A1 - Neher, Dieter T1 - On the relation between the open-circuit voltage and quasi-fermi level splitting in efficient perovskite solar cells JF - advanced energy materials N2 - Today's perovskite solar cells (PSCs) are limited mainly by their open‐circuit voltage (VOC) due to nonradiative recombination. Therefore, a comprehensive understanding of the relevant recombination pathways is needed. Here, intensity‐dependent measurements of the quasi‐Fermi level splitting (QFLS) and of the VOC on the very same devices, including pin‐type PSCs with efficiencies above 20%, are performed. It is found that the QFLS in the perovskite lies significantly below its radiative limit for all intensities but also that the VOC is generally lower than the QFLS, violating one main assumption of the Shockley‐Queisser theory. This has far‐reaching implications for the applicability of some well‐established techniques, which use the VOC as a measure of the carrier densities in the absorber. By performing drift‐diffusion simulations, the intensity dependence of the QFLS, the QFLS‐VOC offset and the ideality factor are consistently explained by trap‐assisted recombination and energetic misalignment at the interfaces. Additionally, it is found that the saturation of the VOC at high intensities is caused by insufficient contact selectivity while heating effects are of minor importance. It is concluded that the analysis of the VOC does not provide reliable conclusions of the recombination pathways and that the knowledge of the QFLS‐VOC relation is of great importance. KW - electro-optical materials KW - perovskite solar cells KW - photovoltaic devices KW - thin films Y1 - 2019 U6 - https://doi.org/10.1002/aenm.201901631 SN - 1614-6832 SN - 1614-6840 VL - 9 IS - 33 PB - Wiley-VCH CY - Weinheim ER - TY - THES A1 - Stephan, Niels T1 - Phänomenologische Untersuchungen zur Feuchteempfindlichkeit der elektrischen Eigenschaften von dünnen Polymerfilmen und deren Verwendung für neuartige Feuchtesensoren T1 - Phenomenological research into the humidity sensitivity of the electrical properties of thin polymer films and its use for novel humidity sensors N2 - Ziel dieser Arbeit ist die phänomenologische Untersuchung der Feuchteempfindlichkeit der elektrischen Eigenschaften dünner Polymerschichten. Diese Untersuchungen stellen gleichzeitig Vorarbeiten zur Entwicklung von Prototypen von zwei polymeren Dünnschicht-Feuchtesensoren dar, die sich durch die spezielle Auswahl der feuchtesensitiven Materialien jeweils durch eine besondere Eigenschaft gegenüber kommerziellen Massenprodukten auszeichnen. Ziel der Entwicklungsarbeiten für den ersten Prototypen war die Konstruktion eines schnellen Feuchtesensors, der plötzliche und sprunghafte Feuchteänderungen in der umgebenden Atmosphäre möglichst rasch detektieren kann. Dafür wurden dünne Schichten von Poly-DADMAC auf Interdigitalstrukturen aufgebracht, die einen möglichst direkten Kontakt zwischen feuchtesensitiver Schicht und umgebender, feuchter Atmosphäre gewährleisten. Als Messgrößen dienten die Wechselstromgrößen Widerstand und Kapazität der Schichten. Die Feuchtekennlinien der Schichten zeigen gute Konstanz und hohe Reproduzierbarkeit. Der Widerstand der Schichten ändert sich durch den Einfluss von Feuchte je nach Schichtdicke um 3 bis 5 Größenordnungen und eignet sich als Messgröße für die Feuchtigkeit im gesamten Feuchtebereich. Die Hysterese der Filme konnte auf kleiner als 2,5% r.F. bestimmt werden, die Reproduzierbarkeit auf besser als 1% r.F. Die Ansprechzeit der Schichten lässt sich schichtdickenabhängig zu 1 bis 10 Sekunden bestimmen. Hierbei zeigen besonders die dünnen Schichten kurze Ansprechzeiten. Zielstellung für den zweiten Feuchtesensor war die Entwicklung eines Prototypen, dessen sensitive Schicht sich biostatisch und biozid verhält, so dass er in biotischen Umgebungen eingesetzt werden kann. Es wurden fünf Polysulfobetaine synthetisiert, deren Biozidität und Biostatik mit dem Kontakttest nach Rönnpagel, dem ISO846-Test und Abbautests bestimmt wurde. Zwei Polymere – Poly-DMMAAPS (BT2) und Poly-[MSA-Styren-Sulfobetain] (BT5) – erwiesen sich als ausreichend biozid und biostatisch. Schichten dieser Polymere wurden auf Interdigitalstrukturen aufgezogen, anschließend wurden die Kennlinien dieser Proben aufgenommen. Die Messwerte zeigen für beide Polymere gute Konstanz und eine hohe Reproduzierbarkeit. BT2-Proben sind zwischen 20% und 80% r.F. besonders empfindlich und zeigen über einen Monat keine Langzeitdrift. Vernetzte Proben zeigen bis 50°C keinen temperaturbedingten Abfall der Feuchteempfindlichkeit. Der Einsatz vernetzter BT5-Schichten als kapazitiver Feuchtesensor ist bis etwa 70°C möglich, die Schichten sind selbst nach Lagerung im Hochvakuum und mehrfacher Betauung stabil. Damit liegen zwei funktionsfähige Prototypen von Feuchtesensoren vor, für die die meisten Kennwerte denen von vergleichbaren kommerziellen Feuchtesensoren entsprechen. Gleichzeitig zeichnen sie sich aber durch eine sehr niedrige Ansprechzeit bzw. eine ausreichende Lebensdauer unter biotischen Bedingungen aus. N2 - The topic of this work is the phenomenological investigation of the humidity sensitivity of the electrical properties of thin polymer films. These investigations also act as preparatory work for the development of prototypes of two polymer thin film humidity sensors, which by the choice of the humidity sensitive materials stand out by one special property each compared with commercial mass products. The aim of the development work for the first prototype was the construction of a fast humidity sensor, which can rapidly detect sudden and erratic humidity changes in the surrounding atmosphere. Thin films of poly-DADMAC were prepared on interdigitated structures that allow for undisturbed contact between the sensitive layer and the surrounding humid atmosphere. Measured variables were the ac resistance and capacity of the films. The humidity characteristics of the films show good stability and high reproducibility. Under the influence of humidity the resistance of the films changes by 3 to 5 orders of magnitude, depending on the film thickness, and is suitable to measure the humidity in the entire humidity range. The hysteresis of the films is lower than 2.5% r.h., the reproducibility better than 1% r.h. The response time of the layers can be determined to 1 to 10 seconds, depending on their thickness. The thin films, specifically, show very short response times. The aim for the second humidity sensor was the development of a prototype, where the sensitive film is biostatic and biocide, so that it can be used to measure the humidity in biotic environments. Five polysulfobetaines were synthesized and their biocidity and biostatics were tested with the contact test according to Rönnpagel, the ISO846 test and degradation tests. Two of the polymers - poly-DMMAAPS (BT2) and poly-[MSA-styrene-sulfobetaine] (BT5) - showed sufficient biocidity and biostatics. Films of these polymers were prepared on interdigitated structures, then their humidity characteristics were recorded. The measured values show good stability and high reproducibility for both polymers. Samples of BT2 are highly sensitive between 20% and 80% r.h. and show no long-term drift after one month. Cross-linked samples show no decrease of the humidity sensitivity in temperatures up to 50 degrees Celsius. Cross-linked films of BT5 can be used as a capacitive humidity sensor up to 70 degrees Celsius, and the samples are stable even after storage in high vacuum and multiple dew cycles. These two functional prototypes of humidity sensors show characteristic data comparable to those of commercial sensors. However, they stand out, respectively, with a very short response time and a sufficient life time in biotic environments. KW - Polymere KW - Feuchtesensor KW - dünne Schichten KW - Poly-DADMAC KW - Polysulfobetain KW - polymers KW - humidity sensor KW - thin films KW - poly-DADMAC KW - polysulfobetaine Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-13853 ER - TY - THES A1 - Arvind, Malavika T1 - Regarding the role of aggregation and structural order on the mechanism of molecular doping of semiconducting polymers T1 - Die Rolle von Aggregation und struktureller Ordnung auf den Mechanismus der molekularen Dotierung von halbleitenden Polymeren BT - from solutions to films BT - von Lösungen zu Filmen N2 - Polymeric semiconductors are strong contenders for replacing traditional inorganic semiconductors in electronic applications requiring low power, low cost and flexibility, such as biosensors, flexible solar cells and electronic displays. Molecular doping has the potential to enable this revolution by improving the conductivity and charge transport properties of this class of materials. Despite decades of research in this field, gaps in our understanding of the nature of dopant–polymer interactions has resulted in limited commercialization of this technology. This work aims at providing a deeper insight into the underlying mechanisms of molecular p-doping of semiconducting polymers in the solution and solid-state, and thereby bring the scientific community closer to realizing the dream of making organic semiconductors commonplace in the electronics industry. The role of 1) dopant size/shape, 2) polymer chain aggregation and 3) charge delocalization on the doping mechanism and efficiency is addressed using optical (UV-Vis-NIR) and electron paramagnetic resonance (EPR) spectroscopies. By conducting a comprehensive study of the nature and concentration of the doping-induced species in solutions of the polymer poly(3-hexylthiophene) (P3HT) with 3 different dopants, we identify the unique optical signatures of the delocalized polaron, localized polaron and charge-transfer complex, and report their extinction coefficient values. Furthermore, with X-ray diffraction, atomic force microscopy and electrical conductivity measurements, we study the impact of processing technique and doping mechanism on the morphology and thereby, charge transport through the doped films. This work demonstrates that the doping mechanism and type of doping-induced species formed are strongly influenced by the polymer backbone arrangement rather than dopant shape/size. The ability of the polymer chain to aggregate is found to be crucial for efficient charge transfer (ionization) and polaron delocalization. At the same time, our results suggest that the high ionization efficiency of a dopant–polymer system in solution may subsequently hinder efficient charge transport in the solid-state due to the reduction in the fraction of tie chains, which enable charges to move efficiently between aggregated domains in the films. This study demonstrates the complex multifaceted nature of polymer doping while providing important hints for the future design of dopant-host systems and film fabrication techniques. N2 - Polymer-Halbleiter sind vielversprechende Kandidaten für den Ersatz traditioneller anorganischer Halbleiter in elektronischen Anwendungen, die einen geringen Stromverbrauch, niedrige Kosten und mechanische Flexibilität erfordern, wie z.B. Biosensoren, flexible Solarzellen und elektronische Bildschirme. Molekulare Dotierung hat das Potenzial, diese Revolution zu ermöglichen, indem sie die Leitfähigkeit und die Ladungstransporteigenschaften dieser Materialklasse verbessert. Trotz jahrzehntelanger Forschung auf diesem Gebiet hat das unvollständige Verständnis der Dotierstoff-Polymer-Wechselwirkungen nur zu einer begrenzten Kommerzialisierung dieser Technologie geführt.Ziel dieser Arbeit ist es, einen tieferen Einblick in die zugrunde liegenden Mechanismen der molekularen p-Dotierung von halbleitenden Polymeren in Lösung und im festen Zustand zu geben und dadurch die wissenschaftliche Gemeinschaft näher an die Verwirklichung des Traums heran zu bringen, organische Halbleiter in der Elektronikindustrie alltäglich zu machen. Diese Arbeit zeigt, dass der Dotierungsmechanismus und die Art der gebildeten, dotierungsinduzierten Spezies eher durch die Anordnung des Polymerrückgrats als durch die Form/Größe des Dotierstoffs beeinflusst werden. Die Fähigkeit der Polymerkette, zu aggregieren, stellt sich als entscheidend für einen effizienten Ladungstransfer (d.h. Ionisierung) und die Polaron-Delokalisierung heraus. Gleichzeitig deuten unsere Ergebnisse darauf hin, dass die hohe Ionisationseffizienz eines Dotierstoff-Polymersystems in der Lösung eine Beinträchtigung des effizienten Ladungstransport im festen Zustand nach sich ziehen kann, da der Anteil der Verbindungsketten, die eine effiziente Bewegung von Ladungen zwischen aggregierten Domänen in dünnen Filmen ermöglichen, reduziert wird. Diese Arbeit verdeutlicht die komplexe, vielschichtige Natur der Polymerdotierung und gibt dabei wichtige Hinweise für das zukünftige Design von Dotierstoff-Wirtssystemen und Filmherstellungstechniken. KW - molecular doping KW - organic semiconductors KW - Lewis acid doping KW - optical spectroscopy KW - thin films KW - semiconducting polymer KW - conductivity KW - dip doping KW - polymer aggregation KW - Dotierung KW - Polymer-Halbleiter KW - Leitfähigkeit KW - Lewis-Säure Dotierung KW - organische Halbleiter KW - Polymeraggregation KW - halbleitendes Polymer KW - Dünn film KW - optische Spektroskopie KW - molekulare Dotierung KW - Dip-Dotierung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-500606 ER -