TY - THES A1 - Ba, Jianhua T1 - Nonaqueous synthesis of metal oxide nanoparticles and their assembly into mesoporous materials T1 - Nichtwässrige Synthese von Metalloxid-Nanopartikeln und deren Anordnung zu mesoporösen Materialien N2 - This thesis mainly consist of two parts, the synthesis of several kinds of technologically interesting crystalline metal oxide nanoparticles via nonaqueous sol-gel process and the formation of mesoporous metal oxides using some of these nanoparticles as building blocks via evaporation induced self-assembly (EISA) technique. In the first part, the experimental procedures and characterization results of successful syntheses of crystalline tin oxide and tin doped indium oxide (ITO) nanoparticles are reported. SnO2 nanoparticles exhibit monodisperse particle size (3.5 nm in average), high crystallinity and particularly high dispersibility in THF, which enable them to become the ideal particulate precursor for the formation of mesoporous SnO2. ITO nanoparticles possess uniform particle morphology, narrow particle size distribution (5-10 nm), high crystallinity as well as high electrical conductivity. The synthesis approaches and characterization of various mesoporous metal oxides, including TiO2, SnO2, mixture of CeO2 and TiO2, mixture of BaTiO3 and SnO2, are reported in the second part of this thesis. Mesoporous TiO2 and SnO2 are presented as highlights of this part. Mesoporous TiO2 was produced in the forms of both films and bulk material. In the case of mesoporous SnO2, the study was focused on the high order of the porous structure. All these mesoporous metal oxides show high crystallinity, high surface area and rather monodisperse pore sizes, which demonstrate the validity of EISA process and the usage of preformed crystalline nanoparticles as nanobuilding blocks (NBBs) to produce mesoporous metal oxides. N2 - Diese Arbeit besteht hauptsächlich aus zwei Teilen. Der erste Teil befasst sich mit der Synthese von mehreren technologisch wichtigen, kristallinen Metalloxid-Nanopartikeln mittels nichtwässriger Sol-Gel Chemie. Der zweite Teil beinhaltet die Herstellung von mesoporösen Metalloxiden. Dabei wurden ausgewählte Nanopartikel als Bausteine verwendet und durch langsames Verdampfen des Lösungsmittels in die entsprechenden porösen Strukturen überführt. Das experimentelle Vorgehen wie auch die Charakterisierung der erfolgreich hergestellten Zinnoxid- und Indiumzinnoxid-Nanopartikel sind im ersten Teil beschrieben. Die Zinnoxid-Nanpartikel zeichnen sich durch einheitliche Partikelgrösse (im Durchschnitt ca. 3.5 nm), hoher Kristallinität, und guter Dispergierbarkeit in Tetrahydrofuran aus. Diese Eigenschaften machen aus den Zinnoxid-Nanopartikeln die perfekten Bausteine für den Aufbau von mesoporösem Zinnoxid. Die Indiumzinnoxid-Nanopartikel haben eine einheitliche Partikelform, eine schmale Grösseverteilung (5-10 nm), hohe Kristallinität wie auch gute elektrische Leitfähigkeit. Die Synthese und Charakterisierung von verschiedenen mesoporösen Metalloxiden wie TiO2, SnO2, Mischungen von CeO2 und TiO2, wie auch Mischungen von BaTiO3 und SnO2 werden im zweiten Teil der Arbeit diskutiert. Mesoporöses TiO2 und SnO2 werden als besonders gelungene Beispiele herausgehoben. Mesoporöses TiO2 wurde in Form von Dünnfilmen wie auch als Bulkmaterial hergestellt. Im Falle von SnO2 galt das Augenmerk vor allem der hohen Ordnung der Mesoporen. Alle diese mesoporösen Materialien zeigen eine hohe Kristallinität, grosse Oberfläche und relativ einheitliche Porengrössen. Diese Eigenschaften unterstreichen, wie wertvoll der Ansatz ist, vorgeformte Nanopartikel als Bausteine für die Synthese von porösen Materialien zu verwenden. KW - Nanopartikel KW - transparent-leitendes Oxid KW - Selbstorganisation KW - nanoparticles KW - oxides KW - assembly KW - mesostructure Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-10173 ER - TY - THES A1 - Bomm, Jana T1 - Von Gold Plasmonen und Exzitonen : Synthese, Charakterisierung und Applikationen von Gold Nanopartikeln T1 - Of gold plasmons and excitons : synthesis, characterization and applications of gold nanoparticles N2 - In dieser Arbeit wurden sphärische Gold Nanopartikel (NP) mit einem Durchmesser größer ~ 2 nm, Gold Quantenpunkte (QDs) mit einem Durchmesser kleiner ~ 2 nm sowie Gold Nanostäbchen (NRs) unterschiedlicher Länge hergestellt und optisch charakterisiert. Zudem wurden zwei neue Synthesevarianten für die Herstellung thermosensitiver Gold QDs entwickelt werden. Sphärische Gold NP zeigen eine Plasmonenbande bei ~ 520 nm, die auf die kollektive Oszillation von Elektronen zurückzuführen ist. Gold NRs weisen aufgrund ihrer anisotropen Form zwei Plasmonenbanden auf, eine transversale Plasmonenbande bei ~ 520 nm und eine longitudinale Plasmonenbande, die vom Länge-zu-Durchmesser-Verhältnis der Gold NRs abhängig ist. Gold QDs besitzen keine Plasmonenbande, da ihre Elektronen Quantenbeschränkungen unterliegen. Gold QDs zeigen jedoch aufgrund diskreter Energieniveaus und einer Bandlücke Photolumineszenz (PL). Die synthetisierten Gold QDs besitzen eine Breitbandlumineszenz im Bereich von ~ 500-800 nm, wobei die Lumineszenz-eigenschaften (Emissionspeak, Quantenausbeute, Lebenszeiten) stark von den Herstellungs-bedingungen und den Oberflächenliganden abhängen. Die PL in Gold QDs ist ein sehr komplexes Phänomen und rührt vermutlich von Singulett- und Triplett-Zuständen her. Gold NRs und Gold QDs konnten in verschiedene Polymere wie bspw. Cellulosetriacetat eingearbeitet werden. Polymernanokomposite mit Gold NRs wurden erstmals unter definierten Bedingungen mechanisch gezogen, um Filme mit optisch anisotropen (richtungsabhängigen) Eigenschaften zu erhalten. Zudem wurde das Temperaturverhalten von Gold NRs und Gold QDs untersucht. Es konnte gezeigt werden, dass eine lokale Variation der Größe und Form von Gold NRs in Polymernanokompositen durch Temperaturerhöhung auf 225-250 °C erzielt werden kann. Es zeigte sich, dass die PL der Gold QDs stark temperaturabhängig ist, wodurch die PL QY der Proben beim Abkühlen (-7 °C) auf knapp 30 % verdoppelt und beim Erhitzen auf 70 °C nahezu vollständig gelöscht werden konnte. Es konnte demonstriert werden, dass die Länge der Alkylkette des Oberflächenliganden einen Einfluss auf die Temperaturstabilität der Gold QDs hat. Zudem wurden verschiedene neuartige und optisch anisotrope Sicherheitslabels mit Gold NRs sowie thermosensitive Sicherheitslabel mit Gold QDs entwickelt. Ebenso scheinen Gold NRs und QDs für die und die Optoelektronik (bspw. Datenspeicherung) und die Medizin (bspw. Krebsdiagnostik bzw. -therapie) von großem Interesse zu sein. N2 - In this thesis, the synthesis and optical characterization of spherical gold nanoparticles (NP) with diameters larger than ~ 2 nm, gold quantum dots (QDs) with diameters smaller than ~ 2 nm and gold nanorods (NRs) with different lengths are presented. In addition, a novel one-pot synthesis for the preparation of thermosensitive gold QDs is introduced. Gold NP solutions appear red colored due to their strong absorption in the visible range at ~ 520 nm. This absorption band is a result of surface plasmon resonance, which is caused by the coherent oscillation of conduction band electrons induced by an electromagnetic field. In contrast to spherical gold NPs, gold NRs show two surface plasmon bands due to their anisotropic shape, a transverse plasmon band at ~ 520 nm and a longitudinal plasmon band depending on the aspect ratio (length-to-width-ratio) of the gold NRs. If the size of the gold NPs decreases to values below ~ 2 nm, quantum-size confinement occurs and the surface plasmon band disappears. Additionally, the overlap between conduction band and valence band disappears, discrete electronic levels arise and a band gap is created. As a consequence of quantum confinement, the gold QDs show photoluminescence (PL) upon UV-irradiation. The gold QDs synthesized via the one-pot synthesis exhibit a broadband luminescence between 500 nm and 800 nm. The luminescence properties (emission peak, quantum yield, lifetime) strongly depend on the synthetic parameters like reaction temperature, stoichiometry and the surface ligand. Gold NRs and gold QDs were incoroporated into different polymers (e.g. cellulose triacetate). Polymer nanocomposite films showing optical anisotropy are obtainded by stretching polymer films containing gold NRs uniaxial in a tensile test machine. In addition to the optical characterization of gold NRs and QDs, their thermal behavior in solution as well as in different nanocomposites is studied. A shortening of the gold NRs or a transformation into spherical gold NP is observed, if the polymer nanocomposites containing gold NRs are heated above a temperature of 200 °C. The PL of the synthesized gold QDs strongly depends on the ambient temperature. An increase of PL quantum yield (QY) and PL lifetime occur, if the solutions are cooled. The best PL QY of 16.6 % was observed for octadecyl mercaptan capped gold QDs at room temperature, which could be improved to 28.6 % when cooling the solutions to -7 °C. Furthermore, optically anisotropic security labels containing gold NRs and thermosensitive security devices containing gold QDs are developed. Due to their unique optical properties, gold NRs and QDs are interesting candidates for optoelectronical as well as data storage devices and medical applications like biomedical imaging or cancer therapy. KW - Gold KW - Nanopartikel KW - Quantenpunkte KW - Nanostäbchen KW - Oberflächenplasmonenlasmonen KW - gold KW - nanoparticles KW - quantum dots KW - nanorods KW - surface plasmons Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-66402 ER - TY - THES A1 - Buha, Jelena T1 - Nonaqueous syntheses of metal oxide and metal nitride nanoparticles T1 - Nichtwässrige Synthesen von Metalloxid- und Metallnitrid-Nanopartikeln N2 - Nanostructured materials are materials consisting of nanoparticulate building blocks on the scale of nanometers (i.e. 10-9 m). Composition, crystallinity and morphology can enhance or even induce new properties of the materials, which are desirable for todays and future technological applications. In this work, we have shown new strategies to synthesise metal oxide and metal nitride nanomaterials. The first part of the work deals with the study of nonaqueous synthesis of metal oxide nanoparticles. We succeeded in the synthesis of In2O3 nanopartcles where we could clearly influence the morphology by varying the type of the precursors and the solvents; of ZnO mesocrystals by using acetonitrile as a solvent; of transition metal oxides (Nb2O5, Ta2O5 and HfO2) that are particularly hard to obtain on the nanoscale and other technologically important materials. Solvothermal synthesis however is not restricted to formation of oxide materials only. In the second part we show examples of nonaqueous, solvothermal reactions of metal nitrides, but the main focus lies on the investigation of the influence of different morphologies of metal oxide precursors on the formation of the metal nitride nanoparticles. In spite of various reports, the number and variety of nanocrystalline metal nitrides is marginally small by comparison to metal oxides; hence preformed metal oxides as precursors for the preparation of metal nitrides are a logical choice. By reacting oxide nanoparticles with cyanamide, urea or melamine, at temperatures of 800 to 900 °C under nitrogen flow metal nitrides could be obtained. We studied in detail the influence of the starting material and realized that size, crystallinity, type of nitrogen source and temperature play the most important role. We have managed to propose and verify a dissolution-recrystallisation model as the formation mechanism. Furthermore we could show that the initial morphology of the oxides could be retained when ammonia flow was used instead. N2 - Nanostrukturierte Materialien sind Materialien, die aus nanopartikulären Baueinheiten in der Größenordnung von Nanonmetern (d.h. 10-9 m) bestehen. Zusammensetzung, Kristallinität und Morphologie können die natürlichen Eigenschaften dieser Materialien verbessern oder zusätzliche Eigenschaften erzeugen, die für heutige und zukünftige Anwendungen und Verfahren wünschenswert sind. In dieser Arbeit präsentieren wir neue Strategien zur Synthese von Nanopartikeln der Metaloxide und Metalnitride. Im einführenden Teil wird die nichtwässrige Synthese von Metaloxidnanopartikeln beschrieben. Uns gelang die Darstellung von In2O3 Nanopartikeln, deren Größe und Form wir durch die Wahl des Prekursors und des Lösemittels deutlich beeinflussen konnten; von ZnO Mesokristallen durch den Einsatz von Acetonitril als Lösemittel; von Übergangsmetalloxiden (Nb2O5, Ta2O5 and HfO2), die besonders schwer im Nanomaßstab zu erhalten sind und von anderen, technisch relevanten Materialien. Die Möglichkeiten der solvothermalen Synthese sind nicht mit der Darstellung von Oxidmaterialen erschöpft. Im zweiten Teil zeigen wir einige Beispiele nichtwässriger, solvothermaler Synthese von Metalnitriden auf; das Hauptaugenmerk liegt aber auf einer Betrachtung der Einflüsse der Morphologie von Metaloxidnanopartikelprekursoren auf die Bildung der Metalnitridnanopartikel. Die Anzahl und Vielfalt bekannter nanokristalliner Metalnitride ist verschwindend klein im Vergleich zu den Metaloxiden, die in der Fachliteratur etabliert sind und demzufolge einen reichen Baukasten an Prekursoren zur Darstellung von Metalnitriden liefern. Durch die Reaktion von Metaloxidnanopartikeln mit Cyanamid, Urea oder Melamine bei Temperaturen von 800 bis 900 °C unter Stickstofffluss konnten Metalnitride erhalten werden. Eine detaillierte Studie der Reaktionsbedingungen und des Reaktionsablaufs zeigte auf, dass Größe und Kristallinität der Metaloxide, die Art der Stickstoffquelle und die Temperatur die entscheidenden Faktoren sind und legte eine Auflösungs-Rekristallisation als Modelmechanismus dieser Art Reaktion nahe. Darüber hinaus konnte gezeigt worden, dass die anfängliche Morphologie des Oxids unter einem Ammoniafluss beibehalten werden konnte. KW - Nichtwässrige Synthese KW - Nanopartikel KW - Metalloxide KW - Metallnitride KW - nonaqueous synthesis KW - nanoparticles KW - metal oxides KW - metal nitrides Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-18368 ER - TY - THES A1 - Dai, Xiaolin T1 - Synthesis of artificial building blocks for sortase-mediated ligation and their enzymatic linkage T1 - Synthese von artifiziellen Bausteinen für Sortase-vermittelte Ligationen und deren enzymatische Verknüpfung N2 - Das Enzym Sortase A katalysiert die Bildung einer Peptidbindung zwischen der Erkennungssequenz LPXTG und einem Oligoglycin. Während vielfältige Ligationen zwischen Proteinen und verschiedenen Biomolekülen, Proteinen und kleinen synthetischen Molekülen, sowie Proteinen und Oberflächen durchgeführt wurden, besteht das Ziel dieser Arbeit darin, die Sortase-katalysierte Verlinkung von synthetischen Bausteinen zu untersuchen. Dies könnte den Weg bereiten für die Anwendung von Sortase A für chemische Aufgabenstellungen und eventuell sogar in den Materialwissenschaften. Für diese grundsätzliche Untersuchung wurden die verwendeten Bausteine zunächst so einfach wie möglich gehalten und leicht zugängliche SiO2 Nanopartikel und kommerziell erhältliche Polymerblöcke ausgewählt. Die Bausteine wurden als erstes mit den Peptidsequenzen für Sortase-vermittelte Ligationen funktionalisiert. SiO2 Nanopartikel wurden mit Durchmessern von 60 und 200 nm hergestellt und mit C=C Doppelbindungen oberflächenmodifiziert. Dann wurden Peptide mit einem terminalen Cystein kovalent durch eine Thiol-en Reaktion angebunden. An die 60 nm NP wurden Peptide mit einem Pentaglycin und an die 200 nm Partikel Peptide mit LPETG Sequenz gebunden. Auf die gleiche Art und Weise wurden Peptide mit terminalem Cystein an die Polymere Polyethylenglykol (PEG) und Poly(N Isopropylacrylamid) (PNIPAM), die beide über C=C Endgruppen verfügen, gebunden und G5-PEG und PNIPAM-LPETG Konjugate erhalten. Mit den vier Bausteinen wurden nun durch Sortase-vermittelte Ligation NP–Polymer Hybride, NP–NP und Polymer–Polymer Strukturen hergestellt und die Produkte u. a. durch Transmissionselektronen-mikroskopie, MALDI-ToF Massenspektrometrie sowie Dynamische Lichtstreuung charakterisiert. Die Verlinkung dieser synthetischen Bausteine konnte eindeutig gezeigt werden. Das Verwenden von kommerziell erhältlichen Polymeren hat jedoch zu einem Gemisch der Polymer-Peptid Konjugate mit unmodifiziertem Polymer geführt, welches nicht gereinigt werden konnte. Deswegen wurden anschließend Synthesestrategien für reine Peptid-Polymer und Polymer-Peptid Konjugate als Bausteine für Sortase-vermittelte Ligationen entwickelt. Diese basieren auf der RAFT Polymerisation mit CTAs, die entweder an N- oder C-Terminus eines Peptids gebunden sind. GG-PNIPAM wurde durch das Anbinden eines geeigneten RAFT CTAs an Fmoc-GG in einer Veresterungsreaktion, Polymerisation von NIPAM und Abspalten der Fmoc Schutzgruppe synthetisiert. Weiterhin wurden mehrere Peptide durch Festphasen-Peptidsynthese erhalten. Die Anbindung eines RAFT CTAs (oder eines Polymerisationsinitiators) an den N-Terminus eines Peptids kann automatisiert als letzter Schritt in einem Peptid-Synthetisierer erfolgen. Die Synthese eines solchen Konjugats konnte in dem Zeithorizont dieser Arbeit noch nicht erreicht werden. Jedoch existieren mehrere vielversprechende Strategien, um diesen Ansatz mit verschiedenen Kopplungsreagenzien zur Anbindung des CTAs fortzusetzen. Solche Polymer Bausteine können in Zukunft für die Synthese von Protein-Polymer Konjugaten durch Sortase-Katalyse verwendet werden. Außerdem kann der Ansatz auch für die Synthese von Block-Copolymeren aus Polymerblöcken mit Peptidmotiven an beiden Enden ausgebaut werden. Auch wenn bei der grundsätzlichen Untersuchung im Rahmen dieser Arbeit Hybridstrukturen hergestellt wurden, die auch durch traditionelle chemische Synthesen erhalten werden könnten, wird ein Bausatz solcher Bausteine in Zukunft die Synthese neuer Materialien ermöglichen und kann auch den Weg für die Anwendung von Enzymen in den Materialwissenschaften ebnen. In Ergänzung zu Nanopartikeln und Block-Copolymeren können dann auch Hybridmaterialien unter Einbezug von Protein-basierten Bausteinen hergestellt werden. Daher könnten Sortase Enzyme zu einem Werkzeug werden, welches etablierte chemische Verlinkungstechniken ergänzt und mit den hoch spezifischen Peptidmotiven über funktionale Einheiten verfügt, die orthogonal zu allen chemischen Gruppen sind. N2 - The enzyme Sortase A catalyzes the formation of a peptide bond between the recognition sequence LPXTG and an oligoglycine. While manifold ligations between proteins and various biomolecules, proteins and small synthetic molecules as well as proteins and surfaces have been reported, the aim of this thesis was to investigate the sortase-catalyzed linkage between artificial building blocks. Hence, this could pave the way for the use of sortase A for tasks from a chemical point of view and maybe even materials science. For the proof of concept, the studied systems were kept as simple as possible at first by choosing easily accessible silica NPs and commercially available polymers. These building blocks were functionalized with peptide motifs for sortase-mediated ligation. Silica nanoparticles were synthesized with diameters of 60 and 200 nm and surface modified with C=C functionalities. Then, peptides bearing a terminal cysteine were covalently linked by means of a thiol-ene reaction. 60 nm SiO2 NPs were functionalized with pentaglycines, while peptides with LPETG motif were linked to 200 nm silica particles. Polyethyleneglycol (PEG) and poly(N isopropylacrylamide) (PNIPAM) were likewise functionalized with peptides by thiol-ene reaction between cysteine residues and C=C units in the polymer end groups. Hence, G5-PEG and PNIPAM-LPETG conjugates were obtained. With this set of building blocks, NP–polymer hybrids, NP–NP, and polymer–polymer structures were generated by sortase-mediated ligation and the product formation shown by transmission electron microscopy, MALDI-ToF mass spectrometry and dynamic light scatting, among others. Thus, the linkage of these artificial building blocks by the enzyme sortase A could be demonstrated. However, when using commercially available polymers, the purification of the polymer–peptide conjugates was impossible and resulted in a mixture containing unmodified polymer. Therefore, strategies were developed for the own synthesis of pure peptide-polymer and polymer-peptide conjugates as building blocks for sortase-mediated ligation. The designed routes are based on preparing polymer blocks via RAFT polymerization from CTAs that are attached to N- or C-terminus, respectively, of a peptide. GG-PNIPAM was synthesized through attachment of a suitable RAFT CTA to Fmoc-GG in an esterification reaction, followed by polymerization of NIPAM and cleavage of the Fmoc protection group. Furthermore, several peptides were synthesized by solid-phase peptide synthesis. The linkage of a RAFT CTA (or polymerization initiator) to the N-terminus of a peptide can be conducted in an automated fashion as last step in a peptide synthesizer. The synthesis of such a conjugate couldn’t be realized in the time frame of this thesis, but many promising strategies exist to continue this strategy using different coupling reagents. Such polymer building blocks can be used to synthesize protein-polymer conjugates catalyzed by sortase A and the approach can be carried on to the synthesis of block copolymers by using polymer blocks with peptide motifs on both ends. Although the proof of concept demonstrated in this thesis only shows examples that can be also synthesized by exclusively chemical techniques, a toolbox of such building blocks will enable the future formation of new materials and pave the way for the application of enzymes in materials science. In addition to nanoparticle systems and block copolymers, this also includes combination with protein-based building blocks to form hybrid materials. Hence, sortase could become an enzymatic tool that complements established chemical linking technologies and provides specific peptide motifs that are orthogonal to all existing chemical functional groups. KW - sortase-mediated ligation KW - enzyme KW - block copolymers KW - nanoparticles KW - Ligation KW - Enzym KW - Block-Copolymere KW - Nanopartikel Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-420060 ER - TY - JOUR A1 - Dai, Xiaolin A1 - Mate, Diana M. A1 - Glebe, Ulrich A1 - Garakani, Tayebeh Mirzaei A1 - Körner, Andrea A1 - Schwaneberg, Ulrich A1 - Böker, Alexander T1 - Sortase-mediated ligation of purely artificial building blocks JF - Polymers N2 - Sortase A (SrtA) from Staphylococcus aureus has been often used for ligating a protein with other natural or synthetic compounds in recent years. Here we show that SrtA-mediated ligation (SML) is universally applicable for the linkage of two purely artificial building blocks. Silica nanoparticles (NPs), poly(ethylene glycol) and poly(N-isopropyl acrylamide) are chosen as synthetic building blocks. As a proof of concept, NP-polymer, NP-NP, and polymer-polymer structures are formed by SrtA catalysis. Therefore, the building blocks are equipped with the recognition sequence needed for SrtA reaction-the conserved peptide LPETG-and a pentaglycine motif. The successful formation of the reaction products is shown by means of transmission electron microscopy (TEM), matrix assisted laser desorption ionization-time of flight mass spectrometry (MALDI-ToF MS), and dynamic light scattering (DLS). The sortase catalyzed linkage of artificial building blocks sets the stage for the development of a new approach to link synthetic structures in cases where their synthesis by established chemical methods is complicated. KW - sortase-mediated ligation KW - enzymes KW - block copolymers KW - nanoparticles Y1 - 2018 U6 - https://doi.org/10.3390/polym10020151 SN - 2073-4360 VL - 10 IS - 2 PB - MDPI CY - Basel ER - TY - JOUR A1 - Draude, F. A1 - Galla, S. A1 - Pelster, Axel A1 - Tentschert, J. A1 - Jungnickel, H. A1 - Haase, Alfred A1 - Mantion, Alexandre A1 - Thuenemann, Andreas F. A1 - Taubert, Andreas A1 - Luch, A. A1 - Arlinghaus, H. F. T1 - ToF-SIMS and Laser-SNMS analysis of macrophages after exposure to silver nanoparticles JF - Surface and interface analysis : an international journal devoted to the development and application of techniques for the analysis surfaces, interfaces and thin films N2 - Silver nanoparticles (SNPs) are among the most commercialized nanoparticles because of their antibacterial effects. Besides being employed, e. g. as a coatingmaterial for sterile surfaces in household articles and appliances, the particles are also used in a broad range of medical applications. Their antibacterial properties make SNPs especially useful for wound disinfection or as a coating material for prostheses and surgical instruments. Because of their optical characteristics, the particles are of increasing interest in biodetection as well. Despite the widespread use of SNPs, there is little knowledge of their toxicity. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and laser post-ionization secondary neutral mass spectrometry (Laser-SNMS) were used to investigate the effects of SNPs on human macrophages derived from THP-1 cells in vitro. For this purpose, macrophages were exposed to SNPs. The SNP concentration ranges were chosen with regard to functional impairments of the macrophages. To optimize the analysis of the macrophages, a special silicon wafer sandwich preparation technique was employed; ToF-SIMS was employed to characterize fragments originating from macrophage cell membranes. With the use of this optimized sample preparation method, the SNP-exposed macrophages were analyzed with ToF-SIMS and with Laser-SNMS. With Laser-SNMS, the three-dimensional distribution of SNPs in cells could be readily detected with very high efficiency, sensitivity, and submicron lateral resolution. We found an accumulation of SNPs directly beneath the cell membrane in a nanoparticular state as well as agglomerations of SNPs inside the cells. KW - Laser-SNMS KW - ToF-SIMS KW - life sciences KW - imaging KW - nanoparticles KW - three-dimensional depth profiling Y1 - 2013 U6 - https://doi.org/10.1002/sia.4902 SN - 0142-2421 VL - 45 IS - 1 SP - 286 EP - 289 PB - Wiley-Blackwell CY - Hoboken ER - TY - THES A1 - Fortes Martín, Rebeca T1 - Water-in-oil microemulsions as soft-templates to mediate nanoparticle interfacial assembly into hybrid nanostructures T1 - Wasser-in-Öl Mikroemulsionen als Soft-Templat für die Grenzfläche-Anordnung von Nanopartikeln in hybride Nanostrukturen T1 - Microemulsiones de aceite-en-agua como estructuras templadas blandas para el ensamblaje de nanoparticulas en su interfase dando nanoestructuras híbridas N2 - Hybrid nanomaterials offer the combination of individual properties of different types of nanoparticles. Some strategies for the development of new nanostructures in larger scale rely on the self-assembly of nanoparticles as a bottom-up approach. The use of templates provides ordered assemblies in defined patterns. In a typical soft-template, nanoparticles and other surface-active agents are incorporated into non-miscible liquids. The resulting self-organized dispersions will mediate nanoparticle interactions to control the subsequent self-assembly. Especially interactions between nanoparticles of very different dispersibility and functionality can be directed at a liquid-liquid interface. In this project, water-in-oil microemulsions were formulated from quasi-ternary mixtures with Aerosol-OT as surfactant. Oleyl-capped superparamagnetic iron oxide and/or silver nanoparticles were incorporated in the continuous organic phase, while polyethyleneimine-stabilized gold nanoparticles were confined in the dispersed water droplets. Each type of nanoparticle can modulate the surfactant film and the inter-droplet interactions in diverse ways, and their combination causes synergistic effects. Interfacial assemblies of nanoparticles resulted after phase-separation. On one hand, from a biphasic Winsor type II system at low surfactant concentration, drop-casting of the upper phase afforded thin films of ordered nanoparticles in filament-like networks. Detailed characterization proved that this templated assembly over a surface is based on the controlled clustering of nanoparticles and the elongation of the microemulsion droplets. This process offers versatility to use different nanoparticle compositions by keeping the surface functionalization, in different solvents and over different surfaces. On the other hand, a magnetic heterocoagulate was formed at higher surfactant concentration, whose phase-transfer from oleic acid to water was possible with another auxiliary surfactant in ethanol-water mixture. When the original components were initially mixed under heating, defined oil-in-water, magnetic-responsive nanostructures were obtained, consisting on water-dispersible nanoparticle domains embedded by a matrix-shell of oil-dispersible nanoparticles. Herein, two different approaches were demonstrated to form diverse hybrid nanostructures from reverse microemulsions as self-organized dispersions of the same components. This shows that microemulsions are versatile soft-templates not only for the synthesis of nanoparticles, but also for their self-assembly, which suggest new approaches towards the production of new sophisticated nanomaterials in larger scale. N2 - Hybride Nanomaterialen ermöglichen die Kombination von individuellen Eigenschaften jeder Art von Nanopartikeln. Einige Strategien für die Herstellung neuer großskaliger Nanostrukturen beruhen auf der Selbstassemblierung von Nanopartikeln über einen Bottom-up-Ansatz. Die Nutzung von Templatstrukturen ermöglicht Anordnungen in definierten Mustern. In einem typischen Soft-Templat werden Nanopartikel und andere oberflächenaktive Wirkstoffe in nicht-mischbare Flüssigkeiten eingebracht. Die resultierenden selbst-organisierten Dispersionen beeinflussen die Nanopartikel Interaktionen und kontrollieren die nachfolgende Selbstassemblierung. Insbesondere Interaktionen zwischen Nanopartikeln mit sehr unterschiedlicher Dispergierbarkeit und Funktionalität können Interaktionen an einer Flüssig-Flüssig Grenzfläche gerichtet werden. In diesem Forschungsprojekt wurden Wasser-in-Öl Mikroemulsionen aus quasi-ternären Mischungen mit Aerosol-OT als Tensid hergestellt. Oleyl-beschichtete superparamagnetische Eisenoxid und/oder Silber Nanopartikel wurden in der kontinuierlichen Ölphase eingebracht, während die Polyethyleneimin-stabilisierten Gold Nanopartikel in feinverteilte Wassertröpfchen inkorporiert wurden. Jede Sorte von Nanopartikeln kann den Tensidfilm und die Tröpfchen-Interaktionen auf verschiedene Weise beeinflussen, und seine Kombination führt dabei zu synergetischen Effekten. Die Anordnung von Nanopartikeln an der Grenzfläche basiert auf der Phasentrennung. Auf der einen Seite, bildeten sich aus einem zweiphasigen Winsor II System mit niedrigen Tensid Konzentrationen durch Evaporation der oberen Phase dünne Schichten aus geordneten Nanopartikeln in Form von Filament-Netzen aus. Eine detaillierte Charakterisierung zeigte, dass die Filament-artige Strukturierung auf ein kontrolliertes Nanopartikeln-Clustering und auf die Ausdehnung der Mikroemulsions-Tröpfchen zurückzuführen ist. Dieser Prozess eröffnet flexible Einsatzmöglichkeiten für unterschiedliche Nanopartikel Kompositionen, indem die Oberflächenfunktionalisierung in unterschiedlichen Lösungsmitteln erhalten bleibt, und auch für verschiedenen Lösungsmitteln und über verschiedene Flächen. Auf der anderen Seite wurde ein magnetisches Heterokoagulat in höheren Tensid Konzentration hergestellt, dessen Phasentransfer von Ölsäure in Wasser mit einem anderen zusätzlichen Tensid in einer Ethanol-Wasser Mischung ermöglicht wurde. In Abhängigkeit von der Ausgangstemperatur der initialen Komponenten konnten definierte magnetisch-stimulierbare Öl-in-Wasser Nanostrukturen erhaltet werden. Dabei gelang es Wasser-dispergierbare Nanopartikelkompartimente in eine Matrix-Hülle aus Öl-dispergierbaren Nanopartikeln einzubetten. In dieser Arbeit wurden zwei verschiedene Wege aufgezeigt, um hybride Nanostrukturen aus inversen Mikroemulsionen selbst-organisiert herzustellen. Dies belegt, dass Mikroemulsions-Template nicht nur für die Nanopartikel Synthese geeignet sind, sondern auch für die Herstellung filamentartiger, selbstorganisierter Systeme. Es eröffnen sich hiermit neue Zugänge für die selbstorganisierte Strukturierung von Nanopartikeln auf der Mikrometerskala. N2 - Los nanomateriales híbridos ofrecen la combinación de propiedades individuales de diferentes tipos de nanopartículas. Algunas estrategias para el desarrollo de nuevas nanoestructuras en mayor escala se basan en el auto-ensamblaje (self-assembly) de nanopartículas, como una estrategia “de abajo hacia arriba” (bottom-up). El uso de estructuras de plantilla (templates) proporciona ensamblajes ordenados de formas definidas. En una plantilla blanda típica, las nanopartículas y otros agentes de actividad superficial se incorporan en líquidos no miscibles. Esto da lugar a dispersiones auto-organizadas que mediarán las interacciones entre las nanopartículas, para controlar su auto-ensamblaje resultante. Especialmente las interacciones entre nanopartículas de dispersibilidad y funcionalidades muy diferentes pueden ser redirigidas a una interfase líquido-líquido. En este proyecto se formularon microemulsiones de agua-en-aceite a partir de mezclas cuasi-ternarias con Aerosol-OT (docusato de sodio) como tensioactivo. Las nanopartículas cubiertas de ligandos oleicos, de óxido de hierro superparamagnéticas o de plata, se incorporaron en la fase orgánica continua, mientras que las nanopartículas de oro estabilizadas por polietilenimina fueron confinadas en las gotículas de agua dispersas. Cada tipo de nanopartícula puede modular de fomas muy diversas la capa de tensioactivo y las interacciones entre gotículas, y además su combinación resulta en efectos sinérgicos. Los ensamblajes interfase de nanopartículas se obtuvieron bajo procesos de separación entre fases. Por un lado, a partir de un sistema bifásico de Winsor del tipo II con baja concentración del tensioactivo, la deposición y evaporación de una gota sobre una superficie (drop-casting) de la fase superior proporcionó películas finas de nanopartículas ordenadas como redes de filamentos. Su caracterización detallada probó que este ensamblaje por plantilla sobre una superficie se basa en un agrupamiento (clustering) controlado entre nanopartículas y en la elongación de las gotículas de microemulsiones. Este proceso ofrece versatilidad para usar diferentes composiciones de nanopartículas siempre que su funcionalidad en su superficie se mantenga, además de poder usar diferentes disolventes y sobre diferentes superficies. Por otro lado, un heterocoagulado magnético se formó sobre concentraciones más altas del tensioactivo, y su transferencia de fase desde ácido oleico a agua fue posible usando otro tensioactivo auxiliar en una mezcla de agua y etanol. Cuando los componentes iniciales fueron mezclados al principio bajo calentamiento, se obtuvieron nanoestucturas definidas de aceite-en-agua que responden a un imán, las cuales consisten de dominios de nanopartículas dispersibles en agua que se rodean por un embalaje (matrix-shell) de nanopartículas dispersibles en fase oleosa. De este modo, se demostraron dos propuestas para formar diversos tipos de nanoestructuras híbridas a partir de microemulsiones inversas como dispersiones auto-organizadas de unos mismos componentes. Esto demuestra que las microemulsiones constituyen estructuras de plantilla blandas no sólo para la síntesis de nanopartículas, sino también para su auto-ensamblaje, lo que sugiere novedosas estrategias para la producción de nuevos nanomateriales sofisticados en mayor escala. KW - microemulsions KW - nanoparticles KW - surfactants KW - Colloid Chemistry KW - soft-templates KW - nanostructures KW - nanoparticle assembly KW - hybrid nanostructures KW - Kolloidchemie KW - hybride Nanostrukturen KW - Mikroemulsionen KW - Nanopartikeln-Anordnung KW - Nanopartikeln KW - Nanostrukturen KW - Soft-Templaten KW - Tenside KW - Química de Coloides KW - nanoestructuras híbridas KW - microemulsiones KW - ensamblaje de nanopartículas KW - nanopartículas KW - nanoestructuras KW - estructuras templadas blandas KW - tensioactivos Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-571801 ER - TY - JOUR A1 - Gu, Sasa A1 - Risse, Sebastian A1 - Lu, Yan A1 - Ballauff, Matthias T1 - Mechanism of the oxidation of 3,3′,5,5′-tetramethylbenzidine catalyzed by peroxidase-like Pt nanoparticles immobilized in spherical polyelectrolyte brushes BT - a kinetic study JF - ChemPhysChem N2 - Experimental and kinetic modelling studies are presented to investigate the mechanism of 3,3 ',5,5 '-tetramethylbenzidine (TMB) oxidation by hydrogen peroxide (H2O2) catalyzed by peroxidase-like Pt nanoparticles immobilized in spherical polyelectrolyte brushes (SPB-Pt). Due to the high stability of SPB-Pt colloidal, this reaction can be monitored precisely in situ by UV/VIS spectroscopy. The time-dependent concentration of the blue-colored oxidation product of TMB expressed by different kinetic models was used to simulate the experimental data by a genetic fitting algorithm. After falsifying the models with abundant experimental data, it is found that both H2O2 and TMB adsorb on the surface of Pt nanoparticles to react, indicating that the reaction follows the Langmuir-Hinshelwood mechanism. A true rate constant k, characterizing the rate-determining step of the reaction and which is independent on the amount of catalysts used, is obtained for the first time. Furthermore, it is found that the product adsorbes strongly on the surface of nanoparticles, thus inhibiting the reaction. The entire analysis provides a new perspective to study the catalytic mechanism and evaluate the catalytic activity of the peroxidase-like nanoparticles. KW - kinetics KW - nanoparticles KW - reaction mechanisms KW - spherical polyelectrolyte KW - brushes KW - UV KW - vis spectroscopy Y1 - 2019 U6 - https://doi.org/10.1002/cphc.201901087 SN - 1439-4235 SN - 1439-7641 VL - 21 IS - 5 SP - 450 EP - 458 PB - Wiley-VCH CY - Weinheim ER - TY - THES A1 - Haase, Martin F. T1 - Modification of nanoparticle surfaces for emulsion stabilization and encapsulation of active molecules for anti-corrosive coatings T1 - Nanopartikel Oberflächenmodifikationen zur Emulsionsstabilisierung und Verkapselung von Wirkstoffen für Antikorrosionsbeschichtungen N2 - Within this work, three physicochemical methods for the hydrophobization of initially hydrophilic solid particles are investigated. The modified particles are then used for the stabilization of oil-in-water (o/w) emulsions. For all introduced methods electrostatic interactions between strongly or weakly charged groups in the system are es-sential. (i) Short chain alkylammonium bromides (C4 – C12) adsorb on oppositely charged solid particles. Macroscopic contact angle measurements of water droplets under air and hexane on flat silica surfaces in dependency of the surface charge density and alkylchain-length allow the calculation of the surface energy and give insights into the emulsification properties of solid particles modified with alkyltrimethylammonium bromides. The measure-ments show an increase of the contact angle with increasing surface charge density, due to the enhanced adsorp-tion of the oppositely charged alkylammonium bromides. Contact angles are higher for longer alkylchain lengths. The surface energy calculations show that in particular the surface-hexane or surface-air interfacial en-ergy is being lowered upon alkylammonium adsorption, while a significant increase of the surface-water interfa-cial energy occurs only at long alkyl chain lengths and high surface charge densities. (ii) The thickness and the charge density of an adsorbed weak polyelectrolyte layer (e.g. PMAA, PAH) influence the wettability of nanoparticles (e.g. alumina, silica, see Scheme 1(b)). Furthermore, the isoelectric point and the pH range of colloidal stability of particle-polyelectrolyte composites depend on the thickness of the weak polye-lectrolyte layer. Silica nanoparticles with adsorbed PAH and alumina nanoparticles with adsorbed PMAA be-come interfacially active and thus able to stabilize o/w emulsions when the degree of dissociation of the polye-lectrolyte layer is below 80 %. The average droplet size after emulsification of dodecane in water depends on the thickness and the degree of dissociation of the adsorbed PE-layer. The visualization of the particle-stabilized o/w emulsions by cryogenic SEM shows that for colloidally stable alumina-PMAA composites the oil-water interface is covered with a closely packed monolayer of particles, while for the colloidally unstable case closely packed aggregated particles deposit on the interface. (iii) By emulsifying a mixture of the corrosion inhibitor 8-hydroxyquinoline (8-HQ) and styrene with silica nanoparticles a highly stable o/w emulsion can be obtained in a narrow pH window. The amphoteric character of 8-HQ enables a pH dependent electrostatic interaction with silica nanoparticles, which can render them interfa-cially active. Depending on the concentration and the degree of dissociation of 8-HQ the adsorption onto silica results from electrostatic or aromatic interactions between 8-HQ and the particle-surface. At intermediate amounts of adsorbed 8-HQ the oil wettability of the particles becomes sufficient for stabilizing o/w emulsions. Cryogenic SEM visualization shows that the particles arrange then in a closely packed shell consisting of partly of aggregated domains on the droplet interface. For further increasing amounts of adsorbed 8-HQ the oil wet-tability is reduced again and the particles ability to stabilize emulsions decreases. By the addition of hexadecane to the oil phase the size of the droplets can be reduced down to 200 nm by in-creasing the silica mass fraction. Subsequent polymerization produces corrosion inhibitor filled (20 wt-%) poly-styrene-silica composite particles. The measurement of the release of 8-hydroxyquinoline shows a rapid increase of 8-hydroxyquinoline in a stirred aqueous solution indicating the release of the total content in less than 5 min-utes. The method is extended for the encapsulation of other organic corrosion inhibitors. The silica-polymer-inhibitor composite particles are then dispersed in a water based alkyd emulsion, and the dispersion is used to coat flat aluminium substrates. After drying and cross-linking the polmer-film Confocal Laser Scanning Micros-copy is employed revealing a homogeneous distribution of the particles in the film. Electrochemical Impedance Spectroscopy in aqueous electrolyte solutions shows that films with aggregated particle domains degrade with time and don’t provide long-term corrosion protection of the substrate. However, films with highly dispersed particles have high barrier properties for corrosive species. The comparison of films containing silica-polystyrene composite particles with and without 8-hydroxyquinoline shows higher electrochemical impedances when the inhibitor is present in the film. By applying the Scanning Vibrating Electrode Technique the localized corrosion rate in the fractured area of scratched polymer films containing the silica-polymer-inhibitor composite particles is studied. Electrochemical corrosion cannot be suppressed but the rate is lowered when inhibitor filled composite particles are present in the film. By depositing six polyelectrolyte layers on particle stabilized emulsion droplets their surface morphology changes significantly as shown by SEM visualization. When the oil wettability of the outer polyelectrolyte layer increases, the polyelectrolyte coated droplets can act as emulsion stabilizers themselves by attaching onto bigger oil droplets in a closely packed arrangement. In the presence of 3 mM LaCl3 8-HQ hydrophobized silica particles aggregate strongly on the oil-water inter-face. The application of an ultrasonic field can remove two dimensional shell-compartments from the droplet surface, which are then found in the aqueous bulk phase. Their size ranges up to 1/4th of the spherical particle shell. N2 - Im Rahmen dieser Arbeit wurden drei Oberflächenmodifikationen zur Hydrophobierung von ursprünglich hydrophilen Feststoffpartikeln entwickelt. Die so modifizierten Partikel werden dann zur Stabilisierung von Öl-in-Wasser Emulsionen verwendet. Für sämtliche entwickelte Methoden sind elektrostatische Wechselwirkungen zwischen stark oder schwach dissoziierten chemischen Gruppen essentiell. (i) Kurzkettige Alkyltrimethylammonium Bromide (C4-C12) adsorbieren auf entgegengesetzt geladenen Partikeln. Makroskopische Kontaktwinkelmessungen von Wasser Tropfen in Luft und Hexan auf flachen Siliziumoxid Oberflächen mit variabler Oberflächenladungsdichte und Alkylkettenlänge ermöglichen die Berechnung der Oberflächenenergie und geben Einblicke in die Emulgationseigenschaften von so modifizierten Feststoffpartikeln. Die Messungen zeigen einen Anstieg des Kontakwinkels mit steigender Oberflächenladungsdichte, bedingt durch die verstärkte Adsorption von entgegengesetzt geladenen Alkyltrimethylammonium Bromiden. Die Kontaktwinkel sind zudem größer für längerkettige Alkyltrimethylammonium Bromide. Die Berechnungen der Oberflächenenergie zeigen, dass besonders die Feststoff-Hexan oder Feststoff-Luft Grenzflächenenergie durch die Adsorption verringert wird, wohingegen die Feststoff-Wasser Oberflächenenergie nur bei längeren Alkylkettenlängen und hohen Oberflächenladungsdichten signifikant ansteigt. (ii) Die Schichtdicke und Ladungsdichte von adsorbierten schwachen Polyelektrolyten (z.B. PMAA, PAH) beeinflusst die Benetzbarkeit von Nanopartikeln (z.B. Aluminiumoxid, Siliziumoxid). Der isoelektrische Punkt und der pH Bereich für kolloidale Stabilität solcher Polyelektrolyt modifizierter Partikel hängt von der Dicke der Polyelektrolytschicht ab. Siliziumoxid und Aluminiumoxid Nanopartikel mit adsorbierten PAH bzw. PMAA werden Grenzflächenaktiv und dadurch befähigt Öl-in-Wasser Emulsionen zu stabilisieren, wenn der Dissoziationsgrad der Polyelektrolytschicht geringer als 80 % ist. Die durchschnittliche Tropfengröße von Dodecan-in-Wasser Emulsionen ist abhängig von der Polyelektrolytschichtdicke und dem Dissoziationsgrad. Die Visualisierung von Partikel stabilisierten Öl-in-Wasser Emulsionen durch kryogene REM zeigt, dass im Falle von kolloidal stabilen Aluminiumoxid-PMAA Partikeln die Öl-Tröpfchen mit einer dichtgepackten Partikelhülle belegt sind, während für kolloidal destabilisierte Partikel eine Hülle aus aggregierten Partikeln gefunden wird. (iii) Durch das Emulgieren einer Lösung des Korrosionsinhibitors 8-Hydroxychinolins (8HQ) in Styrol mit Siliziumoxid Nanopartikeln können stabile Öl-in-Wasser Emulsionen in einem pH Fenster von 4 - 6 hergestellt werden. Der amphoterische Charakter von 8HQ ermöglicht eine pH abhängige elektrostatische Wechselwirkung mit den Siliziumdioxid Nanopartikeln, welche diese Grenzflächenaktiv werden lässt. In Abhängigkeit der Konzentration und des Dissoziationsgrads von 8HQ folgt die Adsorption auf Siliziumdioxid aus elektrostatischen oder aromatischen Wechselwirkungen zwischen 8HQ und der Partikeloberfläche. Bei mittleren adsorbierten Mengen wird die Öl Benetzbarkeit der Partikel ausreichend erhöht um Öl-in-Wasser Emulsionen zu stabilisieren. Kryogene REM zeigt, dass die Partikel dann in dicht gepackte Hüllen, mit teilweise aggregierten Domänen auf der Öltröpfchenoberfläche vorliegen. Durch weiter ansteigende adsorbierte 8HQ Mengen wird die Öl-Benetzbarkeit wieder zurückgesetzt und die Emulgationsfähigkeit der Partikel aufgehoben. Durch die Zugabe von Hexadecan zur Öl Phase kann die Tropfengröße durch Erhöhung des Siliziumdioxid Anteils auf 200 nm herabgesetzt werden. Anschließende Polymerisation des Styrols generiert Korrosionsinhibitor gefüllte (20 Gew-%) Polystyrol-Silizumoxid Komposite. Die Messung der Freisetzungsrate von 8HQ zeigt einen schnellen Anstieg der 8HQ Konzentration in einer gerührten wässrigen Lösung innerhalb von 5 Minuten. Die Verkapselungsmethode wird auch für andere organische Korrosionsinhibitoren erweitert. Die Komposite werden dann in einer wasserbasierten Alkydpräpolymeremulsion dispergiert und diese Mischung wird zur Beschichtung von flachen Aluminiumplatten genutzt. Nach Trocknung und Quervernetzung des Films wird Konfokale Laser Mikroskopie dazu verwendet um die räumliche Verteilung der Composite im Film zu visualisieren. Elektrochemische Impedanzspektroskopie zeigt, dass die Barriereeigenschaften des Films durch die Anwesenheit der Komposite verbessert sind. Raster Vibrationselektroden Messungen zeigen, dass die Korrosionsrate in einem Kratzer des Films durch die Anwesenheit der Inhibitor efüllten Komposite reduziert ist. Durch die Ablagerung von 6 Polyelektroytschichten auf Feststoffstabilisierten Emulsionströpfchen verändert sich deren Oberflächenmorphologie deutlich (gezeigt durch REM). Wenn die Ölbenetzbarkeit der äußeren Polyelektrolytschicht ansteigt, dann können solche Polyelektolytbeschichteten Feststoffstabilisierte Emulsionströpfchen selber als Emulsionsstabilisatoren verwendet werden. Diese lagern sich dann in einer dicht gepackten Schicht auf der Oberfläche von größeren Emulsionstropfen ab. In der Gegenwart von 3 mM LaCl3 aggregieren 8HQ modifizierte Siliziumoxid Partikel stark auf der Öl-Wasser Grenzfläche. Der Einsatz von Ultraschall kann aggregierte Schalenbestandteile von der Tropfenoberfläche wegreißen. Diese Wracks können bis zu einem Viertel der Kugelhülle ausmachen und liegen dann als kolloidale Schalen im Wasser vor. KW - Nanopartikel KW - Emulsionen KW - Polyelektrolyte KW - Korrosion KW - Adsorption KW - nanoparticles KW - emulsions KW - polyelectrolytes KW - corrosion KW - adsorption Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-55413 ER - TY - JOUR A1 - Hass, Roland A1 - Reich, Oliver T1 - Photon density wave spectroscopy for dilution-free sizing of highly concentrated nanoparticles during starved-feed polymerization JF - ChemPhysChem : a European journal of chemical physics and physical chemistry KW - analytical methods KW - fiber-optical spectroscopy KW - nanoparticles KW - photon density wave spectroscopy KW - polymerization Y1 - 2011 U6 - https://doi.org/10.1002/cphc.201100323 SN - 1439-4235 VL - 12 IS - 14 SP - 2572 EP - 2575 PB - Wiley-Blackwell CY - Malden ER -