TY - THES A1 - Esen, Cansu T1 - Carbon nitride incorporation in polymer networks T1 - Inkorporation von Kohlenstoffnitrid in Polymernetzwerke BT - light-driven integration and utilization of graphitic carbon nitride into macroscale polymeric networks N2 - The urge of light utilization in fabrication of materials is as encouraging as challenging. Steadily increasing energy consumption in accordance with rapid population growth, is requiring a corresponding solution within the same rate of occurrence speed. Therefore, creating, designing and manufacturing materials that can interact with light and in further be applicable as well as disposable in photo-based applications are very much under attention of researchers. In the era of sustainability for renewable energy systems, semiconductor-based photoactive materials have received great attention not only based on solar and/or hydrocarbon fuels generation from solar energy, but also successful stimulation of photocatalytic reactions such as water splitting, pollutant degradation and organic molecule synthesisThe turning point had been reached for water splitting with an electrochemical cell consisting of TiO2-Pt electrode illuminated by UV light as energy source rather than an external voltage, that successfully pursued water photolysis by Fujishima and Honda in 1972. Ever since, there has been a great deal of interest in research of semiconductors (e.g. metal oxide, metal-free organic, noble-metal complex) exhibiting effective band gap for photochemical reactions. In the case of environmental friendliness, toxicity of metal-based semiconductors brings some restrictions in possible applications. Regarding this, very robust and ‘earth-abundant’ organic semiconductor, graphitic carbon nitride has been synthesized and successfully applied in photoinduced applications as novel photocatalyst. Properties such as suitable band gap, low charge carrier recombination and feasibility for scaling up, pave the way of advance combination with other catalysts to gather higher photoactivity based on compatible heterojunction. This dissertation aims to demonstrate a series of combinations between organic semiconductor g-CN and polymer materials that are forged through photochemistry, either in synthesis or in application. Fabrication and design processes as well as applications performed in accordance to the scope of thesis will be elucidated in detail. In addition to UV light, more attention is placed on visible light as energy source with a vision of more sustainability and better scalability in creation of novel materials and solar energy based applications. N2 - Die Nutzung von Licht bei der Herstellung von Materialien ist ebenso vielversprechend wie herausfordernd. Der stetig steigende Energieverbrauch in Kombination mit dem rasanten Bevölkerungswachstum erfordert Lösungen in der entsprechenden Geschwindigkeit. Daher stehen Materialien, die mit Licht interagieren können und darüber hinaus in fotobasierten Anwendungen einsetzbar sind, im Mittelpunkt des Interesses der Forscher. In der Ära der Nachhaltigkeit und erneuerbarer Energiesysteme haben halbleiterbasierte photoaktive Materialien nicht nur aufgrund der Erzeugung von Solarenergie oder der Herstellung von Brennstoffen aus Sonnenenergie große Aufmerksamkeit erhalten, sondern auch aufgrund des erfolgreichen Einsatzes in photokatalytischen Reaktionen wie zum Beispiel der Wasserspaltung, des Schadstoffabbaus und der Synthese organischer Moleküle. Die Wasserspaltung mit einer elektrochemischen Zelle führte hier zu einem Wendepunkt in der Forschung. Die Zelle bestand aus einer TiO2-Pt-Elektrode, welche mit UV-Licht als Energiequelle anstatt einer sonst üblichen externen Spannung betrieben wurde. 1972 führten Fujishima und Honda somit erfolgreich die Photolyse von Wasser durch. Seitdem besteht ein großes Interesse an der Erforschung von Halbleitern (z. B. Metalloxide, metallfreie organische Stoffe, Edelmetallkomplexe), die eine effektive Bandlücke für photochemische Reaktionen aufweisen. Was jedoch die Umweltfreundlichkeit anbelangt, so bringt die Toxizität von Halbleitern auf Metallbasis einige Einschränkungen mit sich. Um diese Toxizität zu vermeiden wurde der sehr robuste und bezüglich seiner Ausgangsstoffe häufig vorkommende organische Halbleiter Graphitkohlenstoffnitrid synthetisiert und erfolgreich in photoinduzierten Anwendungen als neuartiger Photokatalysator eingesetzt. Eigenschaften wie eine geeignete Bandlücke, geringe Ladungsträgerrekombination und die Möglichkeit der Skalierung ebnen somit den Weg für Kombinationen mit anderen Katalysatoren, um eine höhere Photoaktivität auf der Grundlage einer kompatiblen Heteroverbindung zu erreichen. Diese Dissertation zielt darauf ab, eine Reihe von Kombinationen zwischen dem organischen Halbleitern g-CN und Polymermaterialien zu demonstrieren. Diese werden entweder durch photochemische Reaktionen synthetisiert oder in solchen angewendet. Die Herstellungs- und Designprozesse sowie die Anwendungen, die im Rahmen dieser Arbeit durchgeführt wurden, werden im Detail erläutert. Neben UV-Licht wird auch dem sichtbarem Licht als Energiequelle mehr Aufmerksamkeit gewidmet. Durch die Verwendung von sichtbaren Licht können die Materialen in solarenergetischen Anwendungen genutzt werden und die Nachhaltigkeit und Skalierbarkeit der Materialien wird verbessert. KW - polymer chemistry KW - Polymerchemie KW - carbon nitride KW - Kohlenstoffnitriden KW - heterogeneous photocatalysis KW - heterogene Photokatalyse Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-576253 ER - TY - THES A1 - Chea, Sany T1 - Glycomaterials: From synthesis of glycoconjugates to potential biomedical applications T1 - Glykomaterialien: Von der Synthese von Glykokonjugaten zu potenziellen biomedizinischen Anwendungen N2 - The importance of carbohydrate structures is enormous due to their ubiquitousness in our lives. The development of so-called glycomaterials is the result of this tremendous significance. These are not exclusively used for research into fundamental biological processes, but also, among other things, as inhibitors of pathogens or as drug delivery systems. This work describes the development of glycomaterials involving the synthesis of glycoderivatives, -monomers and -polymers. Glycosylamines were synthesized as precursors in a single synthesis step under microwave irradiation to significantly shorten the usual reaction time. Derivatization at the anomeric position was carried out according to the methods developed by Kochetkov and Likhorshetov, which do not require the introduction of protecting groups. Aminated saccharide structures formed the basis for the synthesis of glycomonomers in β-configuration by methacrylation. In order to obtain α-Man-based monomers for interactions with certain α-Man-binding lectins, a monomer synthesis by Staudinger ligation was developed in this work, which also does not require protective groups. Modification of the primary hydroxyl group of a saccharide was accomplished by enzyme-catalyzed synthesis. Ribose-containing cytidine was transesterified using the lipase Novozym 435 and microwave irradiation. The resulting monomer synthesis was optimized by varying the reaction partners. To create an amide bond instead of an ester bond, protected cytidine was modified by oxidation followed by amide coupling to form the monomer. This synthetic route was also used to isolate the monomer from its counterpart guanosine. After obtaining the nucleoside-based monomers, they were block copolymerized using the RAFT method. Pre-synthesized pHPMA served as macroCTA to yield cytidine- or guanosine-containing block copolymer. These isolated block copolymers were then investigated for their self-assembly behavior using UV-Vis, DLS and SEM to serve as a potential thermoresponsive drug delivery system. N2 - Die Bedeutung von Kohlenhydratstrukturen ist immens, da sie in unserem Leben allgegenwärtig sind. Die Entwicklung sogenannter Glykomaterialien ist das Ergebnis dieser großen Bedeutung. Diese werden nicht nur zur Erforschung grundlegender biologischer Prozesse eingesetzt, sondern unter anderem auch als Hemmstoffe für Krankheitserreger oder als Wirkstofftransportsysteme. Die vorliegende Arbeit beschreibt die Entwicklung von Glycomaterialien durch die Synthese von Glycoderivaten, -monomeren und -polymeren. Glycosylamine wurden als Vorstufen in einem einzigen Syntheseschritt unter Mikrowellenbestrahlung synthetisiert, um die übliche Reaktionszeit deutlich zu verkürzen. Die Derivatisierung an der anomeren Position wurde nach den von Kochetkov und Likhorshetov entwickelten Methoden durchgeführt, die keine Einführung von Schutzgruppen erfordern. Die aminierten Saccharidstrukturen bildeten die Grundlage für die Synthese von Glycomonomeren in β-Konfiguration durch Methacrylierung. Um α-Man-basierte Monomere für Interaktionen mit bestimmten α-Man-bindenden Lektinen zu erhalten, wurde in dieser Arbeit eine Monomersynthese durch Staudinger-Ligation entwickelt, die ebenfalls keine Schutzgruppen erfordert. Die Modifizierung der primären Hydroxylgruppe eines Saccharids wurde durch enzymkatalysierte Synthese erreicht. Ribosehaltiges Cytidin wurde mit Hilfe der Lipase Novozym 435 und Mikrowellenbestrahlung umgeestert. Die resultierende Monomersynthese wurde durch Variation der Reaktionspartner optimiert. Um eine Amidbindung anstelle einer Esterbindung zu erzeugen, wurde geschütztes Cytidin durch Oxidation und anschließende Amidkupplung modifiziert, um das Monomer zu bilden. Dieser Syntheseweg wurde auch zur Isolierung des Monomers aus seinem Gegenstück Guanosin verwendet. Nach der Gewinnung der nukleosidbasierten Monomere wurden diese mit Hilfe der RAFT-Methode blockcopolymerisiert. Vorsynthetisiertes pHPMA diente als MakroCTA, um Cytidin- oder Guanosin-haltige Blockcopolymere zu erhalten. Diese isolierten Blockcopolymere wurden dann mit UV-Vis, DLS und SEM auf ihr Selbstorganisationsverhalten untersucht, um als potenzielles thermoresponsives Drug-Delivery-System zu dienen. KW - polymer chemistry KW - glyco chemistry KW - glycomonomer KW - glycopolymer KW - lectin KW - drug delivery KW - thermoresponsive KW - glycoconjugate KW - Glykochemie KW - Glykokonjugat KW - Glykomonomer KW - Glykopolymer KW - Lektin KW - Polymerchemie KW - thermoresponsiv KW - Drug Delivery Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-574240 ER - TY - THES A1 - Izraylit, Victor T1 - Reprogrammable and tunable actuation in multiblock copolymer blends T1 - Reprogrammierbare und abstimmbare Aktuation in Blenden von Multiblock Copolymeren N2 - Soft actuators have drawn significant attention due to their relevance for applications, such as artificial muscles in devices developed for medicine and robotics. Tuning their performance and expanding their functionality are frequently done by means of chemical modification. The introduction of structural elements rendering non-synthetic modification of the performance possible, as well as control over physical appearance and facilitating their recycling is a subject of a great interest in the field of smart materials. The primary aim of this thesis was to create a shape-memory polymeric actuator, where the capability for non-synthetic tuning of the actuation performance is combined with reprocessability. Physically cross-linked polymeric matrices provide a solid material platform, where the in situ processing methods can be employed for modification of the composition and morphology, resulting in the fine tuning of the related mechanical properties and shape-memory actuation capability. The morphological features, required for shape-memory polymeric actuators, namely two crystallisable domains and anchoring points for physical cross-links, were embedded into a multiblock copolymer with poly(ε-caprolactone) and poly(L-lactide) segments (PLLA-PCL). Here, the melting transition of PCL was bisected into the actuating and skeleton-forming units, while the cross-linking was introduced via PLA stereocomplexation in blends with oligomeric poly(D-lactide) (ODLA). PLLA segment number average length of 12-15 repeating units was experimentally defined to be capable of the PLA stereocomplexes formation, but not sufficient for the isotactic crystallisation. Multiblock structure and phase dilution broaden the PCL melting transition, facilitating its separation into two conditionally independent crystalline domains. Low molar mass of the PLA stereocomplex components and a multiblock structure enables processing and reprocessing of the PLLA-PCL / ODLA blends with common non-destructive techniques. The modularity of the PLLA-PCL structure and synthetic approach allows for independent tuning of the properties of its components. The designed material establishes a solid platform for non-synthetic tuning of thermomechanical and structural properties of thermoplastic elastomers. To evaluate the thermomechanical stability of the formed physical network, three criteria were appraised. As physical cross-links, PLA stereocomplexes have to be evenly distributed within the material matrix, their melting temperature shall not overlap with the thermal transitions of the PCL domains and they have to maintain the structural integrity within the strain ε ranges further applied in the shape-memory actuation experiments. Assigning PCL the function of the skeleton-forming and actuating units, and PLA stereocomplexes the role of physical netpoints, shape-memory actuation was realised in the PLLA-PCL / ODLA blends. Reversible strain of shape-memory actuation was found to be a function of PLA stereocomplex crystallinity, i.e. physical cross-linking density, with a maximum of 13.4 ± 1.5% at PLA stereocomplex content of 3.1 ± 0.3 wt%. In this way, shape-memory actuation can be tuned via adjusting the composition of the PLLA-PCL / ODLA blend. This makes the developed material a valuable asset in the production of cost-effective tunable soft polymeric actuators for the applications in medicine and soft robotics. N2 - Weiche Polymer-Aktuatoren haben, dank ihrer Bedeutung bei Anwendungen wie z.B. als künstliche Muskeln in Geräten oder in Medizin und Robotik, maßgeblich Aufmerksamkeit erregt. Das Einstellen ihrer Leistung und die Erweiterung ihrer Funktionalität werden oft mittels chemischer Modifizierung durchgeführt. Die Einführung struktureller Elemente, die durch nicht-synthetische Prozesse hervorgerufene Einstellung von Eigenschaften, sowie die Kontrolle der physikalischen Parameter und die Möglichkeit, das Material erneut zu verarbeiten, sind von besonderem Interesse für das Design von intelligenten Werkstoffen. Das Ziel dieser Doktorarbeit war es einen polymeren Formgedächtnis-Aktuator zu entwickeln, der die durch nicht-synthetische Prozesse hervorgerufene Einstellung der Aktuator Parameter mit erneuter Formgebung kombiniert. Physikalisch vernetzte Polymermatrizen stellen dafür eine solide Materialbasis dar, wobei in situ Verarbeitungsmethoden zum Ändern der Zusammensetzung und der Morphologie verwendet werden können. Die Folge davon ist eine präzise Einstellung der entsprechenden mechanischen Eigenschaften und der Formgedächtnis-Aktuator-Leistung. Die morphologischen Elemente, die für die polymeren Formgedächtnis-Aktuatoren benötig werden, nämlich zwei kristallisierbare Domänen und Verankerungspunkte für die physikalischen Cross-Links, wurden in einem Multiblock-Copolymer aus Poly(ε-Caprolakton) und Poly(L-Lactid) Segmenten (PLLA-PCL) integriert. Die Cross-Links wurden durch PLA-Stereokomplexe in Blends mit Poly(D-Lactid) Oligomer (ODLA) geformt. Um die thermomechanische Beständigkeit der hergestellten physikalischen Vernetzung einzuschätzen, wurden drei Kriterien bewertet. Die Erfüllung des morphologischen Kriteriums, gleichmäßige Verteilung innerhalb des Materials, wurde aus der Mikrophasenstruktur abgeleitet. Diese bestand aus einer kontinuierlichen PCL Phase und den isolierten PLA Domänen mit einem durchschnittlichen Domänenabstand von nm Maßstab. Die Schmelzübergänge von PLA Stereokomplexen und PCL überschnitten sich nicht, womit das thermische Kriterium erfüllt wurde. Die Gehalts- und Dehnungsbereiche der strukturelle Beständigkeit der PLA Stereokomplexe wurde in einer detaillierten Untersuchung der mechanischen Eigenschaften mittels Zug-, Dehnungsrückstellungs- und Spannungsrelaxationsversuchen definiert. Indem PCL die skelettbildende und die Aktuatorfunktion zugeordnet wurde, und die PLA Stereokomplexe die Rolle des physikalischen Netzwerks übernehmen, lassen sich in den PLLA-PCL / ODLA Polymerblends Formgedächtniseffekte ausführen. Des Weiteren wurde die Formgedächtnis-Aktuation ε′rev als eine Funktion des Gehalts an PLA Stereokomplex φc mit einem extremalen Charakter festgestellt, d.h. von der Dichte der physikalischen Cross-Links abhängt. Dadurch könnte ε′rev im PLLA-PCL / ODLA System mittels Variation der Zusammensetzung eingestellt werden. Dies verschafft dem entwickelten Polymermaterial ein wertvoller Vorteil bei der Herstellung von kosteffektiven, skalierbaren polymeren Formgedächtnis-Aktuatoren für Anwendungen in der Medizin und der Robotik. KW - Actuator KW - Shape-memory KW - Multiblock copolymer KW - Thermoplastic elastomer KW - Stereocomplex KW - Polymer physics KW - Polymer chemistry KW - Aktuator KW - Multiblock Copolymer KW - Polymerchemie KW - Polymerphysik KW - Formgedächtnis KW - Stereokomplex KW - thermoplastisches Elastomer Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-518434 ER - TY - THES A1 - Kumru, Baris T1 - Utilization of graphitic carbon nitride in dispersed media T1 - Anwendung von graphitischem Kohlenstoffnitrid in dispergierten Medien N2 - Utilization of sunlight for energy harvesting has been foreseen as sustainable replacement for fossil fuels, which would also eliminate side effects arising from fossil fuel consumption such as drastic increase of CO2 in Earth atmosphere. Semiconductor materials can be implemented for energy harvesting, and design of ideal energy harvesting devices relies on effective semiconductor with low recombination rate, ease of processing, stability over long period, non-toxicity and synthesis from abundant sources. Aforementioned criteria have attracted broad interest for graphitic carbon nitride (g-CN) materials, metal-free semiconductor which can be synthesized from low cost and abundant precursors. Furthermore, physical properties such as band gap, surface area and absorption can be tuned. g-CN was investigated as heterogeneous catalyst, with diversified applications from water splitting to CO2 reduction and organic coupling reactions. However, low dispersibility of g-CN in water and organic solvents was an obstacle for future improvements. Tissue engineering aims to mimic natural tissues mechanically and biologically, so that synthetic materials can replace natural ones in future. Hydrogels are crosslinked networks with high water content, therefore are prime candidates for tissue engineering. However, the first requirement is synthesis of hydrogels with mechanical properties that are matching to natural tissues. Among different approaches for reinforcement, nanocomposite reinforcement is highly promising. This thesis aims to investigate aqueous and organic dispersions of g-CN materials. Aqueous g-CN dispersions were utilized for visible light induced hydrogel synthesis, where g-CN acts as reinforcer and photoinitiator. Varieties of methodologies were presented for enhancing g-CN dispersibility, from co-solvent method to prepolymer formation, and it was shown that hydrogels with diversified mechanical properties (from skin-like to cartilage-like) are accessible via g-CN utilization. One pot photografting method was introduced for functionalization of g-CN surface which provides functional groups towards enhanced dispersibility in aqueous and organic media. Grafting vinyl thiazole groups yields stable additive-free organodispersions of g-CN which are electrostatically stabilized with increased photophysical properties. Colloidal stability of organic systems provides transparent g-CN coatings and printing g-CN from commercial inkjet printers. Overall, application of g-CN in dispersed media is highly promising, and variety of materials can be accessible via utilization of g-CN and visible light with simple chemicals and synthetic conditions. g-CN in dispersed media will bridge emerging research areas from tissue engineering to energy harvesting in near future. N2 - Sonnenlicht kann fossile Brennstoffe in der Energieerzeugung ersetzen und ermöglicht neben der Nutzung einer nachhaltigen Ressource dabei auch die deutliche Reduktion der Umweltbelastung in der Energieerzeugung. Die Verfügbarkeit geeigneter Energiegewinnungstechnologien hängt entscheidend von der Verfügbarkeit geeigneter Superkondensatoren (SC) ab. Ideale SC sollten sich in diesem Zusammenhang durch eine geringe Rekombinationsrate, gute Verarbeitbarkeit, Langzeitstabilität, Ungiftigkeit und die Verfügbarkeit aus nachhaltigen Ressourcen auszeichnen. Graphitisches Kohlenstoffnitrid (graphitic carbon nitride – g-CN), ein metall-freier Halbleiter, der aus nachhaltigen und in großer Menge verfügbaren Ausgangsstoffen hergestellt werden kann, ist als Material für dieses Eigenschaftsprofil hervorragend geeignet. Darüber hinaus können die Eigenschaften dieses Materials (innere Oberfläche, Bandlücke, Lichtabsorption) eingestellt werden. Daraus ergibt sich ein großes Forschungsinteresse z.B. im Bereich heterogener Katalyse, wie in der Kohlenstoffdioxidreduktion, elektrolytischen Wasserspaltung und verschiedener organischer Kupplungsreaktionen. Unglücklicherweise ist die schlechte Dispergierbarkeit von g-CN in organischen Lösungsmitteln und Wasser ein wesentlicher Hinderungsgrund für die erfolgreiche Nutzbarmachung dieser hervorragenden Eigenschaften. Das Design von Materialien, die biologisches Gewebe in seinen mechanischen und biologischen Eigenschaften nachahmen und ersetzen können, ist das Ziel der Gewebekonstruktion (Tissue Engineering – TE). Hydrogele, also Netzwerke mit hohem Wassergehalt, gelten als die vielversprechendsten Materialen in diesem Forschungsfeld. Die Herstellung von Hydrogelen, die biologischem Gewebe in seinen mechanischen Eigenschaften ähnelt gilt allerdings als äußerst schwierig und erfordert die Stabilisierung der Netzwerke. Besonders der Einsatz von Nanoverbundstrukturen (nanocomposites) erscheint in diesem Zusammenhang vielversprechend. Die vorliegende Arbeit beschäftigt sich mit der Untersuchung von g-CN in sowohl wässrigen, als auch organischen Dispersionen. Im Zuge dessen werden wässrige Dispersionen für die Synthese von Hydrogelen, bei der g-CN sowohl als Photoinitiator für die durch sichtbares Licht ausgelöste Vernetzung, als auch als Strukturverstärker fungiert. Zur Verbesserung der Dispergierbarkeit des g CN werden vielseitige Ansätze präsentiert, welche von der Verwendung von Co-Lösungsmitteln bis zur Präpolymerbildung reichen. Durch die aufgezeigten Ansätze können Hydrogele mit unterschiedlichen mechanischen Eigenschaften hergestellt werden (hautartig bis knorpelig). Darüber hinaus wird eine Ein-Topf Synthese für die Oberflächenfunktionalisierung vorgestellt, durch die die Dispergierbarkeit von g-CN in organischen und wässrigen Medien verbessert werden kann. Beispielsweise erlaubt die Oberflächenfunktionalisierung mit Vinylthiazol die Herstellung von kolloidal dispergiertem g-CN mit verbesserten photophysikalischen Eigenschaften ohne zusätzliche Additive und eröffnet damit die Möglichkeit transparenter g-CN Beschichtungen und ermöglicht die Druckbarkeit von g-CN aus handelsüblichen Tintenstrahldruckern. Die Anwendung von g-CN in dispergierten Medien ist vielversprechend, da eine große Zahl sehr vielfältiger Materialien durch die Kombination von g-CN mit sichtbarem Licht aus günstigen, nachhaltigen Ressourcen verfügbar ist. Daher ist zu erwarten, dass g-CN in dispergierten Medien verschiedene im Entstehen begriffene Forschungsfelder von TE bis zur Energiegewinnung überspannen wird. KW - polymer chemistry KW - Polymerchemie KW - photochemistry KW - Photochemie KW - colloid chemistry KW - kolloidchemie KW - hydrogels KW - Hydrogelen Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-427339 ER - TY - THES A1 - Willersinn, Jochen T1 - Self-Assembly of double hydrophilic block copolymers T1 - Selbstorganisation Doppelt Hydrophiler Blockcopolymere BT - organized particles and vesicles beyond amphiphiles BT - organisierte Partikel und Vesikel jenseits von Amphiphilen N2 - The motivation of this work was to investigate the self-assembly of a block copolymer species that attended little attraction before, double hydrophilic block copolymers (DHBCs). DHBCs consist of two linear hydrophilic polymer blocks. The self-assembly of DHBCs towards suprastructures such as particles and vesicles is determined via a strong difference in hydrophilicity between the corresponding blocks leading to a microphase separation due to immiscibility. The benefits of DHBCs and the corresponding particles and vesicles, such as biocompatibility, high permeability towards water and hydrophilic compounds as well as the large amount of possible functionalizations that can be addressed to the block copolymers make the application of DHBC based structures a viable choice in biomedicine. In order to assess a route towards self-assembled structures from DHBCs that display the potential to act as cargos for future applications, several block copolymers containing two hydrophilic polymer blocks were synthesized. Poly(ethylene oxide)-b-poly(N-vinylpyrrolidone) (PEO-b-PVP) and Poly(ethylene oxide)-b-poly(N-vinylpyrrolidone-co-N-vinylimidazole) (PEO-b-P(VP-co-VIm) block copolymers were synthesized via reversible deactivation radical polymerization (RDRP) techniques starting from a PEO-macro chain transfer agent. The block copolymers displayed a concentration dependent self-assembly behavior in water which was determined via dynamic light scattering (DLS). It was possible to observe spherical particles via laser scanning confocal microscopy (LSCM) and cryogenic scanning electron microscopy (cryo SEM) at highly concentrated solutions of PEO-b-PVP. Furthermore, a crosslinking strategy with (PEO-b-P(VP-co-VIm) was developed applying a diiodo derived crosslinker diethylene glycol bis(2-iodoethyl) ether to form quaternary amines at the VIm units. The formed crosslinked structures proved stability upon dilution and transfer into organic solvents. Moreover, self-assembly and crosslinking in DMF proved to be more advantageous and the crosslinked structures could be successfully transferred to aqueous solution. The afforded spherical submicron particles could be visualized via LSCM, cryo SEM and Cryo TEM. Double hydrophilic pullulan-b-poly(acrylamide) block copolymers were synthesized via copper catalyzed alkyne azide cycloaddition (CuAAC) starting from suitable pullulan alkyne and azide functionalized poly(N,N-dimethylacrylamide) (PDMA) and poly(N-ethylacrylamide) (PEA) homopolymers. The conjugation reaction was confirmed via SEC and 1H-NMR measurements. The self-assembly of the block copolymers was monitored with DLS and static light scattering (SLS) measurements indicating the presence of hollow spherical structures. Cryo SEM measurements could confirm the presence of vesicular structures for Pull-b-PEA block copolymers. Solutions of Pull-b-PDMA displayed particles in cryo SEM. Moreover, an end group functionalization of Pull-b-PDMA with Rhodamine B allowed assessing the structure via LSCM and hollow spherical structures were observed indicating the presence of vesicles, too. An exemplified pathway towards a DHBC based drug delivery vehicle was demonstrated with the block copolymer Pull-b-PVP. The block copolymer was synthesized via RAFT/MADIX techniques starting from a pullulan chain transfer agent. Pull-b-PVP displayed a concentration dependent self-assembly in water with an efficiency superior to the PEO-b-PVP system, which could be observed via DLS. Cryo SEM and LSCM microscopy displayed the presence of spherical structures. In order to apply a reversible crosslinking strategy on the synthesized block copolymer, the pullulan block was selectively oxidized to dialdehydes with NaIO4. The oxidation of the block copolymer was confirmed via SEC and 1H-NMR measurements. The self-assembled and oxidized structures were subsequently crosslinked with cystamine dihiydrochloride, a pH and redox responsive crosslinker resulting in crosslinked vesicles which were observed via cryo SEM. The vesicular structures of crosslinked Pull-b-PVP could be disassembled by acid treatment or the application of the redox agent tris(2-carboxyethyl)-phosphin-hydrochloride. The successful disassembly was monitored with DLS measurements. To conclude, self-assembled structures from DHBCs such as particles and vesicles display a strong potential to generate an impact on biomedicine and nanotechnologies. The variety of DHBC compositions and functionalities are very promising features for future applications. N2 - Die Selbstanordnung von amphiphilen Blockcopolymeren in Wasser zu Strukturen höherer Ordnung, wie Partikel oder Vesikel, ist seit vielen Jahren bekannt und findet Anwendung in vielen Aspekten der Medizin und Materialwissenschaft. Allerdings ist die treibende Kraft dieser Selbstanordnung zu Vesikeln, die Hydrophobie des wasserunlöslichen Polmyerblocks, auch ein Hindernis für den gezielten Transport von neuen Medikamenten und Wirkstoffen, da die Membran dieser Vesikel aufgrund des hydrophoben Anteils sehr dicht gepackt ist und eine Diffusion der Wirkstoffe durch diese Membran häufig nur durch hohen synthetischen Aufwand gewährleistet werden kann. Einen möglichen Ausweg bietet die Anwendung von doppelt hydrophilen Blockcopolymeren (DHBCs), respektive Blockcopolymere die aus zwei Polymerblöcken mit unterschiedlicher Hydrophilie bestehen. Ist dieser Unterschied groß genug, können DHBCs Partikel- und Vesikelstrukturen ausbilden, die denen der amphiphilen Blockcopolymere ähnlich sind. Um das Potential von DHBC Strukturen zu untersuchen und einen tieferen Einblick in die fundamentalen Prinzipien dieser Selbstanordnung zu erhalten, wurden in dieser Arbeit fünf verschiedene Blockcopolymere hergestellt. Poly(Ethylenoxid)-b-Poly(N-Vinylpyrrolidon) und Poly(Ethylenoxid)-b-Poly(N-Vinylpyrrolidon-co-N-Vinylimidazol) Blockcopolymere wurden über eine kontrollierte radikalische Polymerisation hergestellt und zeigten eine konzentrationsabhängige Selbstanordnung zu Partikeln mit Größen unter einem Mikrometer. Diese Partikel konnten vernetzt werden, sodass sie auch bei starker Verdünnung nicht zerfallen. Zwei Pullulan-b-Poly(Acrylamid) Blockcopolymere wurden über eine Konjugationsreaktion hergestellt, die die beiden separaten Polymerblöcke miteinander verbindet. Diese Blockcopolymere ordneten sich in Wasser zu Vesikulären Strukturen mit Größen zwischen 250 nm und 500 nm. Des Weiteren war es möglich, einen Farbstoff an ein Blockcopolymer anzubringen und den vesikulären Charakter mit konfokaler Mikroskopie zu untersuchen. Ein Ausblick auf mögliche medizinische Anwendung von DHBCs wurde mit dem letzten Blockcopolymer Pullulan-b-Poly(N-Vinylpyrrolidon) gegeben. Vesikel aus diesem Blockcopolymer wurden mit einem pH- und Redox-responsivem Vernetzer vernetzt und es wurde gezeigt, dass sich die vesikulären Strukturen durch Säurebehandlung zersetzen lassen. Dieses System veranschaulicht die theoretische Anwendungsmöglichkeit von DHBCs im gezielten Medikamententransport. KW - self-assembly KW - double hydrophilic block copolymers KW - polymer chemistry KW - RAFT/MADIX polymerization KW - block copolymer vesicles KW - Selbstorganisation KW - Doppelt hydrophile Blockcopolymere KW - Polymerchemie KW - RAFT/MADIX Polymerisation KW - Blockcopolymervesikel Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-408578 ER - TY - THES A1 - ten Brummelhuis, Niels T1 - Self-assembly of cross-linked polymer micelles into complex higher-order aggregates T1 - Selbstorganisation von vernetzten Polymermizellen zu Komplexen Aggregaten mit höherer Ordnung N2 - The creation of complex polymer structures has been one of the major research topics over the last couple of decades. This work deals with the synthesis of (block co-)polymers, the creation of complex and stimuli-responsive aggregates by self-assembly, and the cross-linking of these structures. Also the higher-order self-assembly of the aggregates is investigated. The formation of poly-2-oxazoline based micelles in aqueous solution and their simultaneous functionalization and cross-linking using thiol-yne chemistry is e.g. presented. By introducing pH responsive thiols in the core of the micelles the influence of charged groups in the core of micelles on the entire structure can be studied. The charging of these groups leads to a swelling of the core and a decrease in the local concentration of the corona forming block (poly(2-ethyl-2-oxazoline)). This decrease in concentration yields a shift in the cloud point temperature to higher temperatures for this Type I thermoresponsive polymer. When the swelling of the core is prohibited, e.g. by the introduction of sufficient amounts of salt, this behavior disappears. Similar structures can be prepared using complex coacervate core micelles (C3Ms) built through the interaction of weakly acidic and basic polymer blocks. The advantage of these structures is that two different stabilizing blocks can be incorporated, which allows for more diverse and complex structures and behavior of the micelles. Using block copolymers with either a polyanionic or a polycationic block C3Ms could be created with a corona which contains two different soluble nonionic polymers, which either have a mixed corona or a Janus type corona, depending on the polymers that were chosen. Using NHS and EDC the micelles could easily be cross-linked by the formation of amide bonds in the core of the micelles. The higher-order self-assembly behavior of these core cross-linked complex coacervate core micelles (C5Ms) was studied. Due to the cross-linking the micelles are stabilized towards changes in pH and ionic strength, but polymer chains are also no longer able to rearrange. For C5Ms with a mixed corona likely network structures were formed upon the collapse of the thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm), whereas for Janus type C5Ms well defined spherical aggregates of micelles could be obtained, depending on the pH of the solution. Furthermore it could be shown that Janus micelles can adsorb onto inorganic nanoparticles such as colloidal silica (through a selective interaction between PEO and the silica surface) or gold nanoparticles (by the binding of thiol end-groups). Asymmetric aggregates were also formed using the streptavidin-biotin binding motive. This is achieved by using three out of the four binding sites of streptavidin for the binding of one three-arm star polymer, end-functionalized with biotin groups. A homopolymer with one biotin end-group can be used to occupy the last position. This binding of two different polymers makes it possible to create asymmetric complexes. This phase separation is theoretically independent of the kind of polymer since the structure of the protein is the driving force, not the intrinsic phase separation between polymers. Besides Janus structures also specific cross-linking can be achieved by using other mixing ratios. N2 - In den letzten Jahrzehnten war die Herstellung von komplizierten Polymerstrukturen ein wichtiges Forschungsthema für Polymerchemiker. Diese Arbeit behandelt die Synthese von (Blockco-)Polymere, die Herstellung von komplexen und stimulus-responsiven Aggregaten (Mizellen) durch Selbstorganisation, sowie die Vernetzung dieser Strukturen. Auch die Anordnung dieser Mizellen zu Aggregaten mit höherer Ordnung wurde untersucht. Zum Beispiel wird die Bildung von Poly(2-oxazolin) basierter Mizellen in wässriger Lösung und die gleichzeitige Funktionalisierung und Vernetzung dieser Mizellen mittels Thiol-In-Chemie beschrieben. Durch die Einführung von pH-responsiven Gruppen in den Kern der Mizellen konnte der Einfluss von geladenen Gruppen im Kern auf das gesamte Aggregat untersucht werden. Das Einführen von Ladung führt zum Quellen des Mizellkerns und damit zu einer niedrigeren lokalen Konzentration von wasserlöslichem Poly(2-ethyl-2-oxazolin) (PEtOx). Diese niedrigere Konzentration ergibt eine Verschiebung des Trübungspunkt dieses Typ I thermoresponsiven Polymers zu höheren Temperaturen. Wenn die Ausdehnung des Kerns nicht erfolgt, z.B. in Anwesenheit einer hohen Salzkonzentration, findet dieser Effekt nicht statt. Ähnliche Strukturen können mithilfe von Mizellen mit komplexen Koazervatkern (English: Complex Coacervate Core Micelles, C3Ms) durch die Interaktion zwischen Polymeren mit negativ und positiv geladenen Blöcken hergestellt werden. Der Vorteil dieser Strukturen ist, dass zwei verschiedene stabilisierende Polymerblöcke in einem Aggregat vereint werden können, was zur Bildung einer Vielzahl noch komplizierterer Strukturen und zu mehr Responsivität führen kann. Mithilfe von Blockcopolymeren, bestehend aus jeweils einen polyionischen Block und einem neutralen Block (z.B. PEtOx, PEO oder poly(N-isopropylacrylamid) (PNIPAAm)), konnten C3Ms hergestellt werden, in denen zwei neutrale Polymere vereint wurden. Es konnte gezeigt werden, dass diese Polymere sowohl gemischt als auch phasensepariert vorliegen können (letzteres ergibt Janus Mizellen), abhängig welche Polymere gewählt werden. Durch Vernetzung im Kern konnten die Mizellen stabilisiert und fixiert werden (C5Ms). Die Selbstanordnung dieser vernetzten Mizellen zu größeren Aggregaten wurde untersucht. Wenn eine Lösung mit vernetzten Mizellen über den Trübungspunkt von PNIPAAm erhitzt wurde, bildeten sich Netzwerke aus Mizellen mit einer gemischten Korona, während Janus Mizellen sich zu wohldefinierten Aggregaten höherer Ordnung anordneten. Weiterhin konnte gezeigt werden, dass Janus Mizellen sich auf der Oberfläche von anorganischen Nanopartikeln anlagern können; z.B. durch die selektive Wechselwirkung zwischen PEO und Silica oder durch die Adsorption von Thiolgruppen auf Gold-Nanopartikeln. Asymmetrische Aggregate konnten auch mithilfe des Streptavidin-Biotin Komplexes erhalten werden. Durch das Binden der Biotin-Endgruppen eines dreiarmigen Sternpolymeren an eine Streptavidin-Einheit und anschließende Belegung der verbliebenen Bindungsstelle mit der Biotin-gruppe eines Homopolymers, können sehr spezifisch zwei verschiedene Polymere in einem Janus Aggregat vereint werden. Auch die Vernetzung des Streptavidins kann erzielt werden, indem andere Mischverhältnisse gewählt werden. KW - Polymerchemie KW - Selbstorganisation KW - Mizellen KW - Janus KW - Vernetzung KW - Polymer chemistry KW - self-assembly KW - micelles KW - Janus KW - cross-linking Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-52320 ER -