TY - THES A1 - Weber, Nancy T1 - Die Synthese "schizomorpher" Copolymer - Latexteilchen Y1 - 2011 CY - Potsdam ER - TY - THES A1 - Weber, Jens T1 - Meso- und mikroporöse Hochleistungspolymere : Synthese, Analytik und Anwendungen T1 - Meso- and microporous high performance polymers : synthesis, characterisation and application N2 - Die Arbeit beschreibt die Synthese, Charakterisierung und Anwendung von meso- und mikroporösen Hochleistungspolymeren. Im ersten Teil wird die Synthese von mesoporösen Polybenzimidazol (PBI) auf der Basis einer Templatierungsmethode vorgestellt. Auf der Grundlage kommerzieller Monomere und Silikatnanopartikel sowie eines neuen Vernetzers wurde ein Polymer-Silikat-Hybridmaterial aufgebaut. Das Herauslösen des Silikats mit Ammoniumhydrogendifluorid führt zu mesoporösen Polybenzimidazolen mit spherischen Poren von 9 bis 11 nm Durchmesser. Die Abhängigkeit der beobachteten Porosität vom Massenverhältnis Silikat zu Polymer wurde ebenso untersucht wie die Abhängigkeit der Porosität vom Vernetzergehalt. Die Porosität vollvernetzter Proben zeigt eine lineare Abhängigkeit vom Verhältnis Silikat zu Polymer bis zu einem Grenzwert von 1. Wird der Grenzwert überschritten, ist teilweiser Porenkollaps zu beobachten. Die Abhängigkeit der Porosität vom Vernetzergehalt bei festem Silikatgehalt ist nichtlinear. Oberhalb einer kritischen Vernetzerkonzentration wird eine komplette Replikation der Nanopartikel gefunden. Ist die Vernetzerkonzentration dagegen kleiner als der kritische Wert, so ist der völlige Kollaps einiger Poren bei Stabilität der verbleibenden Poren zu beobachten. Ein komplett unporöses PBI resultiert bei Abwesenheit des Vernetzers. Die mesoporösen PBI-Netzwerke konnten kontrolliert mit Phosphorsäure beladen werden. Die erhaltenen Addukte wurden auf ihre Protonenleitfähigkeit untersucht. Es kann gezeigt werden, dass die Nutzung der vordefinierten Morphologie im Vergleich zu einem unstrukturierten PBI in höheren Leitfähigkeiten resultiert. Durch die vernetzte Struktur war des Weiteren genügend mechanische Stabilität gegeben, um die Addukte reversibel und bei sehr guten Leitfähigkeiten bis zu Temperaturen von 190°C bei 0% relativer Feuchtigkeit zu untersuchen. Dies ist für unstrukturierte Phosphorsäure/PBI - Addukte aus linearem PBI nicht möglich. Im zweiten Teil der Arbeit wird die Synthese intrinsisch mikroporöser Polyamide und Polyimide vorgestellt. Das Konzept intrinsisch mikroporöser Polymere konnte damit auf weitere Polymerklassen ausgeweitet werden. Als zentrales, strukturinduzierendes Motiv wurde 9,9'-Spirobifluoren gewählt. Dieses Molekül ist leicht und vielfältig zu di- bzw. tetrafunktionellen Monomeren modifizierbar. Dabei wurden bestehende Synthesevorschriften modifiziert bzw. neue Vorschriften entwickelt. Ein erster Schwerpunkt innerhalb des Kapitels lag in der Synthese und Charakterisierung von löslichen, intrinsisch mikroporösen, aromatischen Polyamid und Polyimid. Es konnte gezeigt werden, dass das Beobachten von Mikroporosität stark von der molekularen Architektur und der Verarbeitung der Polymere abhängig ist. Die Charakterisierung der Porosität erfolgte unter Nutzung von Stickstoffsorption, Kleinwinkelröntgenstreuung und Molecular Modeling. Es konnte gezeigt werden, dass die Proben stark vom Umgebungsdruck abhängigen Deformationen unterliegen. Die starke Quellung der Proben während des Sorptionsvorgangs konnte durch Anwendung des "dual sorption" Modells, also dem Auftreten von Porenfüllung und dadurch induzierter Henry-Sorption, erklärt werden. Der zweite Schwerpunkt des Kapitels beschreibt die Synthese und Charakterisierung mikroporöser Polyamid- und Polyimidnetzwerke. Während Polyimidnetzwerke auf Spirobifluorenbasis ausgeprägte Mikroporosität und spezifische Oberflächen von ca. 1100 m²/g aufwiesen, war die Situation für entsprechende Polyamidnetzwerke abweichend. Mittels Stickstoffsorption konnte keine Mikroporosität nachgewiesen werden, jedoch konnte mittels SAXS eine innere Grenzfläche von ca. 300 m²/g nachgewiesen werden. Durch die in dieser Arbeit gezeigten Experimente kann die Grenze zwischen Polymeren mit hohem freien Volumen und mikroporösen Polymeren somit etwas genauer gezogen werden. ausgeprägte Mikroporosität kann nur in extrem steifen Strukturen nachgewiesen werden. Die Kombination der Konzepte "Mesoporosität durch Templatierung" und "Mikroporosität durch strukturierte Monomere" hatte ein hierarchisch strukturiertes Polybenzimidazol zum Ergebnis. Die Präsenz einer Strukturierung im molekularen Maßstab konnte SAXS bewiesen werden. Das so strukturierte Polybenzimidazol zeichnete sich durch eine höhere Protonenleitfähigkeit im Vergleich zu einem rein mesoporösen PBI aus. Der letzte Teil der Arbeit beschäftigte sich mit der Entwicklung einer neuen Synthesemethode zur Herstellung von Polybenzimidazol. Es konnte gezeigt werden, dass lineares PBI in einer eutektischen Salzschmelze aus Lithium- und Kaliumchlorid synthetisiert werden kann. Die Umsetzung der spirobifluorenbasierten Monomere zu löslichem oder vernetztem PBI ist in der Salzschmelze möglich. N2 - The first part of the thesis describes the synthesis and characterisation of cross linked, mesoporous poly(benzimidazole) (PBI) prepared by a hard templating approach. Silica nanoparticles were used as template and removed after the polycondensation by immersing the hybrid material in aqueous NH4HF2 solution. The resulting mesoporous PBI showed surface areas up to 200 m²/g as established by N2 BET and porosities up to 37 vol.-%. The influence of the template and cross linker content on the observable porosity was investigated. Nitrogen sorption and small angle x-ray scattering (SAXS) were employed as analytical techniques. The template morphology was reproduced almost perfectly, yielding spherical pores of 11 nm in diameter if the samples were fully cross linked. It was shown that there is a linear dependence of the porosity on the template content up to a critical weight ratio of silica/polymer. If the silica content is raised above 50 wt.-% partial collapse of pores is observed. The dependence of the porosity on the cross linker content at constant amount of template was found to be non-linear. At the absence of any cross linker, no porosity was observed after template removal. At 10 mol-% cross linker the onset of porosity could be observed. At higher cross linker contents, the porosity was nearly the same as for the fully cross linked PBI. The mesoporous PBI could be loaded with crystalline phosphoric acid to yield highly proton conductive materials. It was shown that the material retains its nanostructure when loaded with phosphoric acid even after annealing at 180_C for 12 h. The conductivity of the nanostructured samples was one to two orders of magnitude higher than the conductivity of a nonstructured sample. The impact of the cross linking density on the conductivity was also investigated. The second part of the work describes the synthesis and characterisation of microporous poly(amide)s and poly(imide)s. 9,9'-spirobifluorene derivatives were used to introduce a rigid, structure-directing motif which prevents the polymer chains from close packing. Firstly, the synthesis of soluble poly(amide)s and poly(imide) is described. It was observed that the microporosity is strongly dependent on the processing of the soluble polymers. In the case when polymers were precipitated from solvents of high polarity no microporosity was observed, while polymers prone to solvation in solvents of lower polarity exhibited microporosity as observed in nitrogen sorption measurements. Wide angle x-ray scattering (WAXS) showed that the microstructure was indeed dependent on the processing conditions. SAXS measurements of the polymers revealed that nitrogen sorption alone is not sufficient for the analysis of the porosity. A significant mismatch between the results obtained by the two methods indicated that only a fraction of the pore volume of the polymers was accessible for nitrogen molecules. The second part of the chapter describes the synthesis, characterisation and application of spirobifluorene based, cross linked poly(amide)s and poly(imide)s. The poly(amide) networks did not show any microporosity when analysed by nitrogen sorption. This led to the conclusion that the amide bond is too weak to withstand the interfacial forces. In contrast, poly(imide) networks exhibited pronounced microporosity with surface areas of around 1000 m2/g. The analysis of these networks was again done by nitrogen sorption and SAXS. Furthermore, molecular modelling was used to calculate the true and apparent densities of the networks. In case of the poly(imide) networks, the results of the various measurement techniques were in reasonable agreement. This indicates that the pore volume was nearly completely accessible. Finally it was established that the structure directing motif is necessary to obtain microporous polymers, as a poly(imide) prepared from a spatially undefined monomer did not feature microporosity. Pressure dependent SAXS measurements showed that the polymer networks undergo significant elastic deformations upon evacuation. This behavior complicates the analysis of the nitrogen sorption data, making it impossible to extract reliable pore size distributions. The third and last part of the thesis deals with the development of a new reaction medium for the synthesis of poly(benzimidazole). An eutectic salt melt, composed of lithium chloride and potassium chloride was used in an ionothermal synthesis of linear PBI, opening a green chemistry route towards PBI. The influence of the reaction conditions on the properties of the resulting polymers was investigated. The new reaction medium allowed furthermore the synthesis of linear and cross linked spirobifluorene based PBIs. This is not easily possible by using the classical synthetic pathways towards PBI. The spirobifluorene based PBIs synthesized in this work did, however not feature intrinsic microporosity. KW - poröse Polymere KW - Röntgenkleinwinkelstreuung KW - Gassorption KW - Protonenleitfähigkeit KW - porous polymers KW - small-angle x-ray scattering KW - gas sorption KW - proton conductivity Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-15994 ER - TY - THES A1 - Wawrzinek, Robert C. W. T1 - Fluoreszenzfarbstoffe mit Dioxolobenzodioxol-Grundgerüst: Synthese, Untersuchungen und Anwendungen Y1 - 2013 CY - Potsdam ER - TY - THES A1 - Wandrey, Christine T1 - Polyelektrolyte : makromolekulare Parameter und Elektrolytverhalten Y1 - 1997 SN - 3-89588-814-1 PB - Cuvillier CY - Göttingen ER - TY - THES A1 - Walther, Sebastian T1 - Funktionalisierung von Ölsäuremethylester und Alkydharzen für die photoinduzierte radikalische Polymerisation im UV Bereich N2 - Die vorliegende Arbeit behandelt die Synthese und Charakterisierung von funktionalisierten Alkydharzen und die photoinduzierte Polymerisation dieser unter Einsatz einer Quecksilberdampflampe oder einer UV LED mit unterschiedlicher Lichtintensität. Der Fokus dieser Arbeit bestand in der gezielten Substitution der internalen Doppelbindungen der Fettsäureester durch reaktivere Gruppen, wie Acrylate oder Methacrylate, welche für Alkydharze in dieser Form so in der Literatur nicht beschrieben sind. Untersuchungen des Polymerisationsverhaltens dieser funktionalisierten Harze wurden mit der Photo DSC durchgeführt, wobei Bis – (4 – methoxybenzoyl) diethylgermanium als Photoinitiator diente. Die Ergebnisse haben gezeigt, dass die Harze radikalisch polymerisiert werden können und eine geringere Abhängigkeit von der Umgebungsatmosphäre (Luftsauerstoff bzw. Stickstoff) vorliegt. Dies ist so in der Literatur für funktionalisierte Alkydharze nicht bekannt. Abmischungen von unterschiedlichen Monomeren und funktionalisierten Harzen bewirkten eine Steigerung der Viskosität sowie eine Verringerung der Sauerstoffinhibierung im Zuge der photoinduzierten Polymerisation unter Luftsauerstoff für die Quecksilberdampflampe und der UV LED. Zur Untersuchung der sauerstoffinhibierenden Wirkung der Harze sind Synthesen unterschiedlicher, funktionalisierter Ölsäuremethylester als Modellsubstanzen durchgeführt worden. Ein verbessertes Polymerisationsverhalten und eine geringe Abhängigkeit von der Umgebungsatmosphäre konnte für die Modelle nachgewiesen werden. Zur Aufklärung des verbesserten Polymerisationsverhaltens sind gezielt Substituenten (Imidazol, Brom, Alkohol, Acetat) in den funktionalisierten Ölsäuremethylester eingebaut worden, um den Einfluss dieser aufzuzeigen. Im Rahmen dieser Synthesen sind neuartige Strukturen synthetisiert worden, welche so in der Literatur nicht beschrieben sind. Die Gegenüberstellung der Polymerisationszeit, der Umsatz der (Meth-)Acrylatgruppen sowie die Zeit zum Erreichen der maximalen Polymerisationsgeschwindigkeit unter Verwendung von unterschiedlichen UV Lichtquellen hat einen Einfluss der Substituenten auf das Polymerisationsverhalten gezeigt. N2 - The present work deals with the synthesis and characterization of functionalized alkyl resins and the photoinduced polymerization of them with different UV light sources. The focus of this work was the targeted substitution of the internal double bonds of fatty acid esters by more reactive groups such as acrylates or methacrylates, which are not described in the literature for alkyd resins in this form. Differences in the basic polymerizability of these functionalized resins were carried out with the Photo DSC, with Bis – (4 – methoxybenzoyl) diethylgermane serving as the photoinitiator. The results showed that the resins could be radically polymerized and also had a lower dependence on the ambient atmosphere. This is not described in the literature for functionalized alkyd resins. Blends of different monomers and the functionalized resins also showed that in addition to the increase in viscosity and the polymerizability of the monomers was improved under atmospheric oxygen. The reference used was methyl oleate, which had been functionalized via the same routes of synthesis and polymerized photochemically. In the context of these syntheses, novel monomers have been synthesized which are thus unknown in the literature.
The reference substances confirmed the behavior of the functionalized resins and showed improved polymerization behavior under atmospheric oxygen. To elucidate these properties, different functionalized methyl oleate have been synthesized to investigate the influence of the substituents on the polymerizability under atmospheric oxygen. In particular, the polymerization time, the conversion of the (meth) acrylate groups and the time to reach the maximum polymerization rate played a decisive role. T2 - Functionalization of methyl oleate and alkyd resins for the photoinduced radical polymerization in the UV region KW - UV KW - Alkydharze KW - Fettsäuren KW - Funktionalisierte Ölsäuremethylester KW - Polymerisation KW - Druckfarben KW - Alkyd resin KW - printing inks KW - fatty acids KW - functionalized methyl oleate KW - polymerization KW - UV Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-421467 ER - TY - THES A1 - Wacker, Philipp T1 - Konformationsanalyse meso-substituierter Porphyrine mittels NMR-Spektroskopie und quantenchemischer Berechnungen Y1 - 2008 CY - Potsdam ER - TY - THES A1 - Wacker, Philipp T1 - Konformationsanalyse meso-substituierter Porphyrine mittels NMR-Spektroskopie und quantenchemischer Berechnungen Y1 - 2008 CY - Potsdam ER - TY - JOUR A1 - Völker, D. A1 - Soyez, Konrad T1 - Mechanisch-biologische Vorbehandlung von zu deponierenden Abfällen Y1 - 1996 ER - TY - THES A1 - Vorwerg, Lars T1 - Elektrokinetische Untersuchungen an Modellkolloiden zur Beurteilung ihrer Stabilität Y1 - 1997 CY - Teltow ER - TY - JOUR A1 - Vorndran, Katja Marianne A1 - Linker, Torsten T1 - Einfache zweistufige ipso-Substitution aromatischer Carbonsäuren durch Alkylhalogenide Y1 - 2003 ER -