TY - THES A1 - Perdigón-Toro, Lorena T1 - On the Generation and Fate of Free Carriers in Non-Fullerene Acceptor Organic Solar Cells N2 - Organic solar cells offer an efficient and cost-effective alternative for solar energy harvesting. This type of photovoltaic cell typically consists of a blend of two organic semiconductors, an electron donating polymer and a low molecular weight electron acceptor to create what is known as a bulk heterojunction (BHJ) morphology. Traditionally, fullerene-based acceptors have been used for this purpose. In recent years, the development of new acceptor molecules, so-called non-fullerene acceptors (NFA), has breathed new life into organic solar cell research, enabling record efficiencies close to 19%. Today, NFA-based solar cells are approaching their inorganic competitors in terms of photocurrent generation, but lag in terms of open circuit voltage (V_OC). Interestingly, the V_OC of these cells benefits from small offsets of orbital energies at the donor-NFA interface, although previous knowledge considered large energy offsets to be critical for efficient charge carrier generation. In addition, there are several other electronic and structural features that distinguish NFAs from fullerenes. My thesis focuses on understanding the interplay between the unique attributes of NFAs and the physical processes occurring in solar cells. By combining various experimental techniques with drift-diffusion simulations, the generation of free charge carriers as well as their recombination in state-of-the-art NFA-based solar cells is characterized. For this purpose, solar cells based on the donor polymer PM6 and the NFA Y6 have been investigated. The generation of free charge carriers in PM6:Y6 is efficient and independent of electric field and excitation energy. Temperature-dependent measurements show a very low activation energy for photocurrent generation (about 6 meV), indicating barrierless charge carrier separation. Theoretical modeling suggests that Y6 molecules have large quadrupole moments, leading to band bending at the donor-acceptor interface and thereby reducing the electrostatic Coulomb dissociation barrier. In this regard, this work identifies poor extraction of free charges in competition with nongeminate recombination as a dominant loss process in PM6:Y6 devices. Subsequently, the spectral characteristics of PM6:Y6 solar cells were investigated with respect to the dominant process of charge carrier recombination. It was found that the photon emission under open-circuit conditions can be almost entirely attributed to the occupation and recombination of Y6 singlet excitons. Nevertheless, the recombination pathway via the singlet state contributes only 1% to the total recombination, which is dominated by the charge transfer state (CT-state) at the donor-acceptor interface. Further V_OC gains can therefore only be expected if the density and/or recombination rate of these CT-states can be significantly reduced. Finally, the role of energetic disorder in NFA solar cells is investigated by comparing Y6 with a structurally related derivative, named N4. Layer morphology studies combined with temperature-dependent charge transport experiments show significantly lower structural and energetic disorder in the case of the PM6:Y6 blend. For both PM6:Y6 and PM6:N4, disorder determines the maximum achievable V_OC, with PM6:Y6 benefiting from improved morphological order. Overall, the obtained findings point to avenues for the realization of NFA-based solar cells with even smaller V_OC losses. Further reduction of nongeminate recombination and energetic disorder should result in organic solar cells with efficiencies above 20% in the future. N2 - Organische Solarzellen bieten eine effiziente und kostengünstige Alternative für die Nutzung von Sonnenenergie. Bei dieser Art von Photovoltaikzellen werden in der Regel zwei organische Halbleiter, ein elektronenspendendes Polymer und ein niedermolekularer Elektronenakzeptor gemischt, um eine sogenannte „Bulk-Heterojunction“ (BHJ)-Morphologie zu erzeugen. Traditionell wurden hierfür Fulleren-basierte Akzeptoren verwendet. In den letzten Jahren hat die Entwicklung neuer Akzeptor-Moleküle, so genannter Nicht-Fulleren-Akzeptoren (NFA), der organischen Solarzellenforschung neues Leben eingehaucht und damit Rekordwirkungsgrade >19 % ermöglicht. Heutzutage nähern sich NFA-basierte Solarzellen ihren anorganischen Konkurrenten bezüglich der Photostromerzeugung an, nicht jedoch im Hinblick auf die Leerlaufspannung (V_OC). Interessanterweise profitiert der V_OC dieser Zellen von kleinen Offsets der Orbitalenergien an der Donor-NFA-Grenzfläche, obwohl nach bisherigem Wissen große Energieoffsets als entscheidend für die effiziente Ladungsträgergenerierung an der Heterogrenzfläche galten. Darüber hinaus gibt es eine Reihe weiterer elektronischer und struktureller Merkmale, die NFAs von Fullerenen unterscheiden. Meine Dissertation konzentriert sich auf ein tiefgreifendes Verständnis des Zusammenspiels der einzigartigen Eigenschaften von NFAs und den physikalischen Prozessen in daraus hergestellten Solarzellen. Durch die Kombination verschiedener experimenteller Techniken mit Drift-Diffusions-Simulationen wird die Erzeugung freier Ladungsträger sowie deren Rekombination in modernen NFA-basierten Solarzellen charakterisiert. Zu diesem Zweck wurden Solarzellen auf Basis des Donor-Polymers PM6 und des NFA Y6 untersucht. Die Erzeugung freier Ladungsträger in PM6:Y6 erweist sich dabei als effizient und unabhängig von elektrischem Feld und Anregungsenergie. Temperaturabhängige Messungen zeigen eine sehr geringe Aktivierungsenergie für die Photostromerzeugung (ca. 6 meV), was auf eine barrierefreie Ladungsträgertrennung hinweist. Theoretische Modellierungen legen nahe, dass Y6-Moleküle große Quadrupolmomente aufweisen, was zu einer Bandverbiegung an der Donor-Akzeptor-Grenzfläche führt und dabei die elektrostatische Coulombsch-Dissoziationsbarriere reduziert. In dieser Hinsicht identifiziert diese Arbeit die schlechte Extraktion freier Ladungen in Konkurrenz zur „nongeminalen“ Rekombination als einen dominanten Verlustprozess in PM6:Y6 Zellen. In weiterer Folge wurden die spektralen Eigenschaften von PM6:Y6-Solarzellen im Hinblick auf den dominanten Prozess der Ladungsträgergenerierung und rekombination untersucht. Es zeigte sich, dass die Photonenemission unter Leerlaufbedingungen fast vollständig auf die Besetzung und Rekombination von Y6-Singlet-Exzitonen zurückgeführt werden kann. Trotzdem trägt der Rekombinationspfad über den Singlett-Zustand nur zu 1 % zur gesamten Rekombination bei, die über den Ladungstransfer-Zustand (CT-state) an der Donor-Akzeptor-Grenzfläche dominiert wird. Weitere V_OC Gewinne sind daher nur zu erwarten, wenn die Dichte und/oder die Rekombinationsrate dieser CT-Zustände erheblich reduziert werden kann. Schließlich wird die Rolle der energetischen Unordnung in NFA-Solarzellen durch den Vergleich von Y6 mit einem strukturverwandten Derivat, genannt N4, untersucht. Untersuchungen zur Schichtmorphologie in Kombination mit Experimenten zum temperaturabhängigen Ladungstransport zeigen eine deutlich geringere strukturelle und energetische Unordnung im Fall des PM6:Y6 Blends. Sowohl für PM6:Y6 als auch für PM6:N4 bestimmt die Unordnung den maximal erreichbaren V_OC, wobei PM6:Y6 von der verbesserten morphologischen Ordnung profitiert. Insgesamt weisen die gewonnenen Erkenntnisse Wege für die Realisierung von NFA-basierten Solarzellen mit noch kleineren V_OC-Verlusten auf. Durch die weitere Reduzierung der „nongeminaten“ Rekombination als auch der energetischen Unordnung sollten in Zukunft organische Solarzellen mit einem Wirkungsgrad von über 20 % möglich werden. T2 - Über die Photogenerierung und Rekombination freier Ladungsträger in organischen Solarzellen mit Nicht-Fulleren-Akzeptoren KW - organic solar cells KW - non-fullerene acceptors KW - free charge generation KW - free charge recombination KW - energetic disorder KW - organic semiconductors KW - energetische Unordnung KW - Generierung freier Ladungsträger KW - freie Ladungsträger Rekombination KW - Nicht-Fulleren-Akzeptoren KW - organische Halbleiter KW - organische Solarzellen Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-558072 ER - TY - THES A1 - Kurpiers, Jona T1 - Probing the pathways of free charge generation and recombination in organic solar cells T1 - Pfade der Generierung und Rekombination freier Ladungsträger in organischen Solarzellen BT - the role of excess energy and dispersive effects BT - die Rolle von Überschussenergie und dispersiven Effekten N2 - Organic semiconductors are a promising class of materials. Their special properties are the particularly good absorption, low weight and easy processing into thin films. Therefore, intense research has been devoted to the realization of thin film organic solar cells (OPVs). Because of the low dielectric constant of organic semiconductors, primary excitations (excitons) are strongly bound and a type II heterojunction needs to be introduced to split these excitations into free charges. Therefore, most organic solar cells consist of at least an electron donor and electron acceptor material. For such donor acceptor systems mainly three states are relevant; the photoexcited exciton on the donor or acceptor material, the charge transfer state at the donor-acceptor interface and the charge separated state of a free electron and hole. The interplay between these states significantly determines the efficiency of organic solar cells. Due to the high absorption and the low charge carrier mobilities, the active layers are usually thin but also, exciton dissociation and free charge formation proceeds rapidely, which makes the study of carrier dynamics highly challenging. Therefore, the focus of this work was first to install new experimental setups for the investigation of the charge carrier dynamics in complete devices with superior sensitivity and time resolution and, second, to apply these methods to prototypical photovoltaic materials to address specific questions in the field of organic and hybrid photovoltaics. Regarding the first goal, a new setup combining transient absorption spectroscopy (TAS) and time delayed collection field (TDCF) was designed and installed in Potsdam. An important part of this work concerned the improvement of the electronic components with respect to time resolution and sensitivity. To this end, a highly sensitive amplifier for driving and detecting the device response in TDCF was developed. This system was then applied to selected organic and hybrid model systems with a particular focus on the understanding of the loss mechanisms that limit the fill factor and short circuit current of organic solar cells. The first model system was a hybrid photovoltaic material comprising inorganic quantum dots decorated with organic ligands. Measurements with TDCF revealed fast free carrier recombination, in part assisted by traps, while bias-assisted charge extraction measurements showed high mobility. The measured parameters then served as input for a successful description of the device performance with an analytical model. With a further improvement of the instrumentation, a second topic was the detailed analysis of non-geminate recombination in a disordered polymer:fullerene blend where an important question was the effect of disorder on the carrier dynamics. The measurements revealed that early time highly mobile charges undergo fast non-geminate recombination at the contacts, causing an apparent field dependence of free charge generation in TDCF experiments if not conducted properly. On the other hand, recombination the later time scale was determined by dispersive recombination in the bulk of the active layer, showing the characteristics of carrier dynamics in an exponential density of state distribution. Importantly, the comparison with steady state recombination data suggested a very weak impact of non-thermalized carriers on the recombination properties of the solar cells under application relevant illumination conditions. Finally, temperature and field dependent studies of free charge generation were performed on three donor-acceptor combinations, with two donor polymers of the same material family blended with two different fullerene acceptor molecules. These particular material combinations were chosen to analyze the influence of the energetic and morphology of the blend on the efficiency of charge generation. To this end, activation energies for photocurrent generation were accurately determined for a wide range of excitation energies. The results prove that the formation of free charge is via thermalized charge transfer states and does not involve hot exciton splitting. Surprisingly, activation energies were of the order of thermal energy at room temperature. This led to the important conclusion that organic solar cells perform well not because of predominate high energy pathways but because the thermalized CT states are weakly bound. In addition, a model is introduced to interconnect the dissociation efficiency of the charge transfer state with its recombination observable with photoluminescence, which rules out a previously proposed two-pool model for free charge formation and recombination. Finally, based on the results, proposals for the further development of organic solar cells are formulated. N2 - Organische Halbleiter sind eine vielversprechende Materialklasse. Ihre besonderen Eigenschaften sind die gute Absorption, das geringe Gewicht und die einfache Verarbeitung zu dünnen Filmen. Daher wird intensiv an der Realisierung organischer Dünnschichtsolarzellen (OPVs) geforscht. Aufgrund der niedrigen Dielektrizitätskonstante organischer Halbleiter sind primäre Anregungen (Exzitonen) jedoch stark gebunden, und es muss ein Typ II-Heteroübergang eingeführt werden, um diese Anregungen in freie Ladungen zu trennen. Daher bestehen die meisten organischen Solarzellen aus mindestens einem Elektronendonator und einem Elektronenakzeptormaterial. Für solche Donator-Akzeptorsysteme sind hauptsächlich drei Zustünde relevant; das Exziton auf dem Donator- oder Akzeptormaterial, der Ladungstransferzustand an der Donator-Akzeptor-Grenzfläche und der ladungsgetrennte Zustand eines freien Elektrons und Lochs. Das Zusammenspiel dieser Zustände bestimmt maßgeblich die Effizienz organischer Solarzellen. Aufgrund der hohen Absorption und der geringen Ladungsträgermobilitäten sind die aktiven Schichten dünn, aber auch die Exzitonendissoziation und die Bildung freier Ladung findet auf kurzen Zeitskalen statt, was die Analyse der Ladungsträgerdynamik erschwert. Im Mittelpunkt dieser Arbeit standen daher zunächst die Installation neuer Versuchsaufbauten zur Untersuchung der Ladungsträgerdynamik in optimierten Solarzellen mit überlegener Empfindlichkeit und Zeitauflösung sowie die Anwendung dieser Methoden auf prototypische photovoltaische Materialien. Im Hinblick auf das erste Ziel wurde ein neuer Aufbau, der optische Methoden wie die zeitaufgelöste Absorptionsspektroskopie (TAS) mit optolektronischen Methoden, wie die zeitaufgelöste Ladungsextraktion (TDCF) kombiniert. Ein wichtiger Teil dieser Arbeit war die Verbesserung der elektronischen Komponenten hinsichtlich der Zeitauflösung und Empfindlichkeit. Zu diesem Zweck wurde ein hochempfindlicher Verstärker zur Ansteuerung und Detektion der Probenantwort in TDCF entwickelt. Dieser Versuchsaufbau wurde im Folgenden auf verschiedene Modellsysteme angewendet, mit besonderem Fokus auf dem Verständnis der Verlustmechanismen, die den Füllfaktor und den Kurzschlussstrom organischer Solarzellen limittieren. Das erste Modellsystem ist ein hybrides Material, das aus anorganischen Quantenpunkten mit organischen Liganden besteht. Messungen mit TDCF ergaben eine schnelle Rekombination freier Ladungsträger, die teilweise durch Fallen unterstützt wurde, während Ladungsextraktionsexperimente unter quasi-konstanter Beleuchtung eine hohe Mobilität zeigten. Mit den gemessenen Parametern konnte die Kennlinie gut mit einem analytischen Modell beschrieben werden. Mit einer weiteren Verbesserung des Aufbaus konnte ein zweites Thema, die detaillierte Analyse der nicht-geminalen Rekombination in einer ungeordneten Polymer-Fulleren-Mischung bearbeitet werden. Die Messungen zeigten, dass hochmobilen Ladungen zu frühen Zeiten eine schnelle, nicht-geminale Rekombination an den Kontakten durchlaufen, was eine scheinbare Feldabhängigkeit der Generierung freier Ladung in TDCF-Experimenten verursachen kann. Andererseits wurde die Rekombination auf längeren Zeitskalen durch dispersive Rekombination in der aktiven Schicht bestimmt, wobei die Ursache der Ladungsträgerdynamik in einer exponentiellen Verteilung der Zustandsdichte liegt. Der Vergleich mit Rekombinationsdaten im stationären Zustand ergab einen sehr schwachen Einfluss nicht-thermalisierter Ladungsträger auf die Rekombinationseigenschaften der Solarzellen unter anwendungsrelevanten Bedingungen. Schließlich wurden temperatur- und feldabhängige Studien zur Erzeugung freier Ladung an drei Donator-Akzeptor-Kombinationen durchgeführt, wobei zwei Donatorpolymere der gleichen Materialfamilie mit zwei verschiedenen Fulleren-Akzeptormolekülen gemischt wurden. Diese besonderen Materialkombinationen wurden ausgewählt, um den Einfluss der Energetik und Morphologie der Mischung auf die Effizienz der Ladungserzeugung zu analysieren. Zu diesem Zweck wurden die Aktivierungsenergien für die Photostromerzeugung für einen weiten Bereich von Anregungsenergien genau bestimmt. Die Ergebnisse beweisen, dass die Bildung freier Ladungen über thermalisierte Ladungstransferzustände erfolgt und keine Aufspaltung mit heißen Exzitonen beinhaltet. Überraschenderweise sind die Aktivierungsenergien vergleichbar mit der thermischen Energie bei Raumtemperatur. Dies führte zu der wichtigen Schlussfolgerung, dass organische Solarzellen nicht aufgrund von hochenergetischen Pfaden gut funktionieren, sondern weil die thermalisierten Ladungstransferzustände schwach gebunden sind. Darüber hinaus wird ein Modell eingeführt, um die Dissoziationseffizienz des Ladungstransferzustands mit seiner mit Photolumineszenz beobachtbaren Rekombination zu verbinden, wodurch ein zuvor vorgeschlagenes Zwei-Pool-Modell für die Bildung und Rekombination von freien Ladungen ausgeschlossen wird. Abschließend werden auf Basis der Ergebnisse Vorschläge zur Weiterentwicklung organischer Solarzellen formuliert. KW - organic solar cells KW - time resolved pump probe spectroscopy Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-429099 ER - TY - THES A1 - Roland, Steffen T1 - Charge carrier recombination and open circuit voltage in organic solar cells T1 - Ladungsträger Rekombination und Leerlaufspannung in organischen Solarzellen BT - from bilayer-model systems to hybrid multi-junctions BT - von Bilayer Modellsystemen zu hybriden Mehrschichtsolarzellen N2 - Tremendous progress in the development of thin film solar cell techniques has been made over the last decade. The field of organic solar cells is constantly developing, new material classes like Perowskite solar cells are emerging and different types of hybrid organic/inorganic material combinations are being investigated for their physical properties and their applicability in thin film electronics. Besides typical single-junction architectures for solar cells, multi-junction concepts are also being investigated as they enable the overcoming of theoretical limitations of a single-junction. In multi-junction devices each sub-cell operates in different wavelength regimes and should exhibit optimized band-gap energies. It is exactly this tunability of the band-gap energy that renders organic solar cell materials interesting candidates for multi-junction applications. Nevertheless, only few attempts have been made to combine inorganic and organic solar cells in series connected multi-junction architectures. Even though a great diversity of organic solar cells exists nowadays, their open circuit voltage is usually low compared to the band-gap of the active layer. Hence, organic low band-gap solar cells in particular show low open circuit voltages and the key factors that determine the voltage losses are not yet fully understood. Besides open circuit voltage losses the recombination of charges in organic solar cells is also a prevailing research topic, especially with respect to the influence of trap states. The exploratory focus of this work is therefore set, on the one hand, on the development of hybrid organic/inorganic multi-junctions and, on the other hand, on gaining a deeper understanding of the open circuit voltage and the recombination processes of organic solar cells. In the first part of this thesis, the development of a hybrid organic/inorganic triple-junction will be discussed which showed at that time (Jan. 2015) a record power conversion efficiency of 11.7%. The inorganic sub-cells of these devices consist of hydrogenated amorphous silicon and were delivered by the Competence Center Thin-Film and Nanotechnology for Photovoltaics in Berlin. Different recombination contacts and organic sub-cells were tested in conjunction with these inorganic sub-cells on the basis of optical modeling predictions for the optimal layer thicknesses to finally reach record efficiencies for this type of solar cells. In the second part, organic model systems will be investigated to gain a better understanding of the fundamental loss mechanisms that limit the open circuit voltage of organic solar cells. First, bilayer systems with different orientation of the donor and acceptor molecules were investigated to study the influence of the donor/acceptor orientation on non-radiative voltage loss. Secondly, three different bulk heterojunction solar cells all comprising the same amount of fluorination and the same polymer backbone in the donor component were examined to study the influence of long range electrostatics on the open circuit voltage. Thirdly, the device performance of two bulk heterojunction solar cells was compared which consisted of the same donor polymer but used different fullerene acceptor molecules. By this means, the influence of changing the energetics of the acceptor component on the open circuit voltage was investigated and a full analysis of the charge carrier dynamics was presented to unravel the reasons for the worse performance of the solar cell with the higher open circuit voltage. In the third part, a new recombination model for organic solar cells will be introduced and its applicability shown for a typical low band-gap cell. This model sheds new light on the recombination process in organic solar cells in a broader context as it re-evaluates the recombination pathway of charge carriers in devices which show the presence of trap states. Thereby it addresses a current research topic and helps to resolve alleged discrepancies which can arise from the interpretation of data derived by different measurement techniques. N2 - In der Photovoltaikforschung spielen neuartige Dünnschichtsolarzellen eine immer größere Rolle. Neben innovativen Design und Anwendungskonzepten sind Material und Kostenreduzierung in der Herstellung die größten Triebfedern für die Entwicklung neuer Technologien. Hier sind neben den vielversprechenden Perowskitsolarzellen insbesondere organische Solarzellen zu nennen, die sich durch ihre chemische Vielseitigkeit, einfache Verarbeitung und stetige Weiterentwicklung in Bezug auf ihre Effizienz auszeichnen. Diese Vielseitigkeit ermöglicht die Herstellung organischer Solarzellen mit unterschiedlicher spektraler Empfindlichkeit, was wiederum Vorteile für den Einsatz in seriengeschaltete Mehrschichtsolarzellen bietet. Diese erlauben es, fundamentale Limitierungen von Einschichtsolarzellsystemen zu überwinden. Der erste Teil dieser Arbeit befasst sich daher mit der Entwicklung einer neuartigen hybriden Multischichtsolarzelle, die sowohl aus anorganischen als auch organischen Subzellen besteht und zum Zeitpunkt ihrer Veröffentlichung einen neuen Effizienzrekord für diese Klasse von Solarzellen aufzeigte. Der zweite Teil der Arbeit befasst sich mit fundamentalen physikalischen Prozessen in organischen Solarzellen, da viele Funktionsmechanismen noch nicht im Detail geklärt sind. An verschiedenen organischen Modellsolarzellsystemen wurde daher unter anderem der Einfluss molekularer Orientierung von Donor- und Akzeptorkomponenten der Solarzelle oder der Einfluss von Fluorinierung des Donors auf die Leerlaufspannung der Solarzelle untersucht. Auf diese Weise konnten neue wichtige Erkenntnisse über den Einfluss von verschiedenen Verlustkanälen und der Energetik auf die Leerlaufspannung gewonnen werden. Der letzte Teil der Arbeit widmet sich der Entwicklung eines neuen Modells, welches den Rekombinationsprozess von Ladungen in einer bestimmten organischen Solarzelle beschreibt. Dieses neue Modell wurde anhand umfangreicher Experimente validiert und ermöglicht es, insbesondere den Einfluss freier und in sogenannten Fallenzuständen gefangener Ladungen auf die Rekombination zu trennen. Damit hat dieses Modell eine weitreichende Bedeutung, zum einen für die Beurteilung von typischen Rekombinationsexperimenten in organischen Solarzellen und zum anderen für die Bewertung des Einflusses von Fallenzuständen auf den Rekombinationsstrom. KW - organic solar cells KW - charge carrier recombination KW - open circuit voltage KW - hybrid multi-junction solar cell KW - organische Solarzellen KW - Ladungsträgerrekombination KW - Leerlaufspannung KW - hybride Mehrschichtsolarzellen Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-397721 ER - TY - THES A1 - Kniepert, Juliane T1 - Correlation between dynamic parameters and device performance of organic solar cells T1 - Zusammenhang zwischen den dynamischen Größen und der Effizienz Organischer Solarzellen N2 - Organic bulk heterojunction (BHJ) solar cells based on polymer:fullerene blends are a promising alternative for a low-cost solar energy conversion. Despite significant improvements of the power conversion efficiency in recent years, the fundamental working principles of these devices are yet not fully understood. In general, the current output of organic solar cells is determined by the generation of free charge carriers upon light absorption and their transport to the electrodes in competition to the loss of charge carriers due to recombination. The object of this thesis is to provide a comprehensive understanding of the dynamic processes and physical parameters determining the performance. A new approach for analyzing the characteristic current-voltage output was developed comprising the experimental determination of the efficiencies of charge carrier generation, recombination and transport, combined with numerical device simulations. Central issues at the beginning of this work were the influence of an electric field on the free carrier generation process and the contribution of generation, recombination and transport to the current-voltage characteristics. An elegant way to directly measure the field dependence of the free carrier generation is the Time Delayed Collection Field (TDCF) method. In TDCF charge carriers are generated by a short laser pulse and subsequently extracted by a defined rectangular voltage pulse. A new setup was established with an improved time resolution compared to former reports in literature. It was found that charge generation is in general independent of the electric field, in contrast to the current view in literature and opposed to the expectations of the Braun-Onsager model that was commonly used to describe the charge generation process. Even in cases where the charge generation was found to be field-dependend, numerical modelling showed that this field-dependence is in general not capable to account for the voltage dependence of the photocurrent. This highlights the importance of efficient charge extraction in competition to non-geminate recombination, which is the second objective of the thesis. Therefore, two different techniques were combined to characterize the dynamics and efficiency of non-geminate recombination under device-relevant conditions. One new approach is to perform TDCF measurements with increasing delay between generation and extraction of charges. Thus, TDCF was used for the first time to measure charge carrier generation, recombination and transport with the same experimental setup. This excludes experimental errors due to different measurement and preparation conditions and demonstrates the strength of this technique. An analytic model for the description of TDCF transients was developed and revealed the experimental conditions for which reliable results can be obtained. In particular, it turned out that the $RC$ time of the setup which is mainly given by the sample geometry has a significant influence on the shape of the transients which has to be considered for correct data analysis. Secondly, a complementary method was applied to characterize charge carrier recombination under steady state bias and illumination, i.e. under realistic operating conditions. This approach relies on the precise determination of the steady state carrier densities established in the active layer. It turned out that current techniques were not sufficient to measure carrier densities with the necessary accuracy. Therefore, a new technique {Bias Assisted Charge Extraction} (BACE) was developed. Here, the charge carriers photogenerated under steady state illumination are extracted by applying a high reverse bias. The accelerated extraction compared to conventional charge extraction minimizes losses through non-geminate recombination and trapping during extraction. By performing numerical device simulations under steady state, conditions were established under which quantitative information on the dynamics can be retrieved from BACE measurements. The applied experimental techniques allowed to sensitively analyse and quantify geminate and non-geminate recombination losses along with charge transport in organic solar cells. A full analysis was exemplarily demonstrated for two prominent polymer-fullerene blends. The model system P3HT:PCBM spincast from chloroform (as prepared) exhibits poor power conversion efficiencies (PCE) on the order of 0.5%, mainly caused by low fill factors (FF) and currents. It could be shown that the performance of these devices is limited by the hole transport and large bimolecular recombination (BMR) losses, while geminate recombination losses are insignificant. The low polymer crystallinity and poor interconnection between the polymer and fullerene domains leads to a hole mobility of the order of 10^-7 cm^2/Vs which is several orders of magnitude lower than the electron mobility in these devices. The concomitant build up of space charge hinders extraction of both electrons and holes and promotes bimolecular recombination losses. Thermal annealing of P3HT:PCBM blends directly after spin coating improves crystallinity and interconnection of the polymer and the fullerene phase and results in comparatively high electron and hole mobilities in the order of 10^-3 cm^2/Vs and 10^-4 cm^2/Vs, respectively. In addition, a coarsening of the domain sizes leads to a reduction of the BMR by one order of magnitude. High charge carrier mobilities and low recombination losses result in comparatively high FF (>65%) and short circuit current (J_SC ≈ 10 mA/cm^2). The overall device performance (PCE ≈ 4%) is only limited by a rather low spectral overlap of absorption and solar emission and a small V_OC, given by the energetics of the P3HT. From this point of view the combination of the low bandgap polymer PTB7 with PCBM is a promising approach. In BHJ solar cells, this polymer leads to a higher V_OC due to optimized energetics with PCBM. However, the J_SC in these (unoptimized) devices is similar to the J_SC in the optimized blend with P3HT and the FF is rather low (≈ 50%). It turned out that the unoptimized PTB7:PCBM blends suffer from high BMR, a low electron mobility of the order of 10^-5 cm^2/Vs and geminate recombination losses due to field dependent charge carrier generation. The use of the solvent additive DIO optimizes the blend morphology, mainly by suppressing the formation of very large fullerene domains and by forming a more uniform structure of well interconnected donor and acceptor domains of the order of a few nanometers. Our analysis shows that this results in an increase of the electron mobility by about one order of magnitude (3 x 10^-4 cm^2/Vs), while BMR and geminate recombination losses are significantly reduced. In total these effects improve the J_SC (≈ 17 mA/cm^2) and the FF (> 70%). In 2012 this polymer/fullerene combination resulted in a record PCE for a single junction OSC of 9.2%. Remarkably, the numerical device simulations revealed that the specific shape of the J-V characteristics depends very sensitively to the variation of not only one, but all dynamic parameters. On the one hand this proves that the experimentally determined parameters, if leading to a good match between simulated and measured J-V curves, are realistic and reliable. On the other hand it also emphasizes the importance to consider all involved dynamic quantities, namely charge carrier generation, geminate and non-geminate recombination as well as electron and hole mobilities. The measurement or investigation of only a subset of these parameters as frequently found in literature will lead to an incomplete picture and possibly to misleading conclusions. Importantly, the comparison of the numerical device simulation employing the measured parameters and the experimental $J-V$ characteristics allows to identify loss channels and limitations of OSC. For example, it turned out that inefficient extraction of charge carriers is a criticical limitation factor that is often disobeyed. However, efficient and fast transport of charges becomes more and more important with the development of new low bandgap materials with very high internal quantum efficiencies. Likewise, due to moderate charge carrier mobilities, the active layer thicknesses of current high-performance devices are usually limited to around 100 nm. However, larger layer thicknesses would be more favourable with respect to higher current output and robustness of production. Newly designed donor materials should therefore at best show a high tendency to form crystalline structures, as observed in P3HT, combined with the optimized energetics and quantum efficiency of, for example, PTB7. N2 - Organische Solarzellen aus Polymer-Fulleren Mischschichten sind eine vielversprechende Alternative für eine kostengünstige Quelle erneuerbarer Energien. Jedoch sind trotz intensiver Forschung und bedeutenden Verbesserungen der Effizienzen während der letzten Jahre, die fundamentalen Prozesse in diesen Solarzellen noch immer nicht vollständig verstanden. Im Allgemeinen wird der Photostrom in organischen Solarzellen durch die Generation freier Ladungsträger nach Absorption von Licht und dem anschliessenden Transport dieser Ladungsträger zu den Elektroden bestimmt, wobei ein Teil durch Rekombination verloren geht. Das Ziel dieser Dissertation ist es, zu einem umfassenden Verständnis aller dynamischen Prozesse und relevanten physikalischen Parameter und deren Zusammenhang mit der Solarzelleneffizienz beizutragen. Dabei wurde eine neue Herangehensweise zur Analyse der Strom-Spannungskennlinien entwickelt, die auf der experimentellen Bestimmung von Ladungsträgergeneration, Rekombination und Transport im Vergleich mit numerischen Simulationen beruht. Die zentralen Fragestellungen zu Beginn der Arbeit waren, in welchem Masse die Ladungsträgergeneration von der Stärke des elektrischen Feldes abhängt und in wie weit die einzelnen Prozesse Generation, Rekombination und Transport zum charakteristischen Verlauf der Strom-Spannungskennlinie beitragen. Eine elegante Methode um direkt die Feldabhängigkeit der Ladungsträgergeneration zu bestimmen, ist die Time Delayed Collection Field (TDCF) Methode. Dabei werden in der Solarzelle Ladungsträger mit einem kurzen Laserpuls erzeugt und anschliessend mit einem wohldefinierten rechteckigen Spannungspuls extrahiert. Im Rahmen dieser Arbeit wurde ein neuer Versuchsaufbau mit stark verbesserter Zeitauflösung im Vergleich zu vorangegangenen Arbeiten aufgebaut. Es hat sich gezeigt, dass die Generation im Allgemeinen nicht vom elektrischen Feld abhängt. Dies steht im Widerspruch zu dem in der Literatur häufig verwendeten Braun-Onsager Modell zur Beschreibung der Ladungsgeneration. Selbst in Fällen, in denen eine feldabhängige Generation gemessen wurde, reichte diese im Allgemeinen nicht aus, um die Spannungsabhängigkeit des Photostroms in diesen Zellen zu erklären. Dies führt zu der zunehmenden Bedeutung einer effizienten Ladungsextraktion in Konkurrenz zur nicht-geminalen Rekombination, welche die zweite wichtige Fragestellung in dieser Arbeit war. Dazu wurden zwei neue Herangehensweisen zur Messung der Rekombinationsdynamik unter Solarzellen-relevanten Messbedingungen erarbeitet. Zum Einen wurde zum ersten Mal TDCF zur Messung von Rekombination und Transport verwendet. Der Vorteil ist, dass die Messung aller drei relevanten Prozesse in einem Versuchsaufbau zu einer höheren Genauigkeit führt, da experimentelle Fehler durch unterschiedliche Probenpräparation und Messbedingungen ausgeschlossen werden können. Es wurde ein analytisches Modell zur Beschreibung der TDCF Transienten entwickelt, welches direkt Rückschlüsse auf die notwendigen Messbedingungen erlaubt, unter denen zuverlässige Ergebnisse erzielt werden können. Insbesondere hat sich dabei gezeigt, dass die RC-Zeit des Aufbaus, die hauptsächlich durch die Probengeometrie bestimmt wird, einen wesentlichen Einfluss auf die Transienten hat, welcher in der Datenauswertung nicht vernachlässigt werden darf. Zum Anderen wurde eine komplementäre Methode zur Messung der Rekombination im Gleichgewicht benutzt, die auf der genauen Bestimmung der statischen Ladungsträgerdichte unter Beleuchtung basiert. Es zeigte sich, dass die in der Literatur etablierten Methoden zur Ladungsträgerbestimmung nicht ausreichend genau waren. Daher wurde eine neue, sensitive Technik entwickelt, die Bias Assisted Charge Extraction (BACE) Methode. Dabei werden die unter kontinuierlicher Beleuchtung generierten Ladungsträger mit einem hohen angelegten elektrischen Feld extrahiert. Dies führt zu einer beschleunigten Extraktion im Vergleich zur konventionellen Charge Extraction Methode, welche die Verluste durch Rekombination und Trapping deutlich reduziert. Mit Hilfe von numerischen Simulationen wurden Bedingungen festgelegt, unter denen zuverlässige Messungen mit BACE möglich sind. Mit den vorgestellten Methoden können alle relevanten Parameter für Generation, Rekombination und Transport experimentell sehr genau bestimmt und analysiert werden. Dies wurde exemplarisch für zwei in der Literatur bedeutende Materialsysteme durchgeführt. Das Modellsystem P3HT:PCBM, hergestellt aus dem Lösungsmittel Chloroform, weist direkt nach der Präparation nur sehr niedrige Effizienzen im Bereich von 0.5% auf, die vor allem durch niedrige Ströme und Füllfaktoren (FF) gekennzeichnet sind. Es konnte gezeigt werden, dass die Effizienz dieser Zellen durch den sehr langsamen Lochtransport und die starke bimolekulare Rekombination begrenzt wird, während Verluste durch geminale Rekombination eher unbedeutend sind. Eine geringe Kristallinität des Polymers und schlechte Verbindungen zwischen den Polymerdomänen führt zu einer Lochmobilität von nur 10^7 cm^2/Vs. Diese ist mehrere Grössenordnungen kleiner als die Elektronenmobilität in diesen Zellen, was den Aufbau von Raumladungen zur Folge hat und damit die Extraktion von beiden Ladungsträgern behindert und bimolekulare Rekombination begünstigt. Die thermische Behandlung der P3HT:PCBM Proben direkt nach dem Spin Coating verbessert sowohl die Kristallinität als auch die Vernetzung der Polymer- und Fullerenphasen. Dies führt zu vergleichsweise hohen Mobilitäten für Elektronen (10^3 cm^2/Vs) und Löcher (10^4 cm^2/Vs). Zusätzlich reduziert eine Vergrösserung der Domänenstruktur die bimolekulare Rekombination um eine Grössenordnung. Die hohen Mobilitäten und niedrigen Rekombinationverluste resultieren in vergleichsweise hohen FF (> 65%) und Strömen (J_SC ≈ 10 mA/cm^2). Die Effizienz (≈ 4%) wird dabei nur durch den eher geringen spektralen Überlapp zwischen Absorptions- und Sonnenemissionsspektrum begrenzt und einer geringen Leerlaufspannung (V_OC), verursacht durch die ungünstige Energetik des P3HT. Aus dieser Perspektive ist die Kombination des Low-Bandgap Polymers PTB7 mit dem Fullerenderivat PCBM ein vielversprechender Ansatz. Aufgrund der angepassten Energetik führt diese Kombination in Mischschichtsolarzellen zu einer höheren V_OC. Jedoch ist der Kurzschlussstrom (J_SC) in den unoptimierten Zellen gegenüber dem der optimierten P3HT:PCBM Zellen nicht erhöht und die FF sind niedrig (≈ 50%). Die Untersuchungen ergaben, dass die Dynamik in den unoptimierten PTB7:PCBM Zellen durch hohe bimolekulare Rekombination (BMR), eine niedrige Elektronenmobilität im Bereich von 10^5 cm^2/Vs und nicht-geminalen Rekombinationsverslusten aufgrund einer feldabhängigen Generation geprägt ist. Die Zugabe des Lösungsmitteladditivs DIO bei der Probenpräparation optimiert die Morphologie in der Schicht. Dabei wird hauptsächlich die Formation von sehr grossen Fullerendomänen unterdrückt und eine gleichmässige Struktur von gut vernetzten, nanometergrossen Donor- und Akzeptordomänen ausgebildet. Unsere Analyse zeigt, dass dadurch die Elektronenmobilität um ca eine Grössenordnung erhöht wird (auf 3 x 10^4 cm^2/Vs), während BMR und geminale Rekombination deutlich unterdrückt werden. Zusammen genommen verbessern diese Effekte sowohl den J_SC (≈ 17 mA/cm^2) als auch den FF (> 70%). Im Jahr 2012 führten die optimierten PTB7:PCBM Solarzellen damit zu einer Rekordeffizienz für organische Solarzellen von 9.2%. Von grösserer Bedeutung ist jedoch, dass der Vergleich zwischen den gemessenen und simulierten Strom-Spannungskennlinien, mit experimentell bestimmten Eingangsparametern, Rückschlüsse auf die entsprechenden Verlustkanäle in den jeweiligen Solarzellen erlaubt. Hierbei zeigte sich, dass die effiziente Extraktion von Ladungsträgern ein kritischer Faktor ist, der in der Literatur oft unterschätzt wird. Der effiziente und schnelle Transport von Ladungen wird aber gerade im Hinblick auf neue Low-Bandgap Materialien mit sehr hohen internen Quanteneffizienzen immer wichtiger. Moderate Mobilitäten limitieren die möglichen Schichtdicken auf ca 100 nm. Grössere Schichtdicken wären jedoch vorteilhafter im Hinblick auf höhere Ausgangsströme und der Robustheit des Produktionsprozesses. Neu entwickelte Donormaterialien sollten daher sowohl möglichst kristalline Strukturen ausbilden mit einhergehenden hohen Mobilitäten, wie beim P3HT, als auch optimierte Energieniveaus und Quanteneffizienzen aufweisen, wie beispielsweise PTB7. KW - organic solar cells KW - optoelectronic measurements KW - transient methods KW - numeric device simulations KW - organische Solarzellen KW - optoelektronische Messungen KW - transiente Messmethoden KW - numerische Bauteilsimulationen Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-90087 ER - TY - THES A1 - Albrecht, Steve T1 - Generation, recombination and extraction of charges in polymer T1 - Generierung, Rekombination und Extraktion von Ladungen in Polymer BT - fullerene bulk heterojunction solar cells BT - Fulleren Mischsolarzellen N2 - A dramatic efficiency improvement of bulk heterojunction solar cells based on electron-donating conjugated polymers in combination with soluble fullerene derivatives has been achieved over the past years. Certified and reported power conversion efficiencies now reach over 9% for single junctions and exceed the 10% benchmark for tandem solar cells. This trend brightens the vision of organic photovoltaics becoming competitive with inorganic solar cells including the realization of low-cost and large-area organic photovoltaics. For the best performing organic materials systems, the yield of charge generation can be very efficient. However, a detailed understanding of the free charge carrier generation mechanisms at the donor acceptor interface and the energy loss associated with it needs to be established. Moreover, organic solar cells are limited by the competition between charge extraction and free charge recombination, accounting for further efficiency losses. A conclusive picture and the development of precise methodologies for investigating the fundamental processes in organic solar cells are crucial for future material design, efficiency optimization, and the implementation of organic solar cells into commercial products. In order to advance the development of organic photovoltaics, my thesis focuses on the comprehensive understanding of charge generation, recombination and extraction in organic bulk heterojunction solar cells summarized in 6 chapters on the cumulative basis of 7 individual publications. The general motivation guiding this work was the realization of an efficient hybrid inorganic/organic tandem solar cell with sub-cells made from amorphous hydrogenated silicon and organic bulk heterojunctions. To realize this project aim, the focus was directed to the low band-gap copolymer PCPDTBT and its derivatives, resulting in the examination of the charge carrier dynamics in PCPDTBT:PC70BM blends in relation to by the blend morphology. The phase separation in this blend can be controlled by the processing additive diiodooctane, enhancing domain purity and size. The quantitative investigation of the free charge formation was realized by utilizing and improving the time delayed collection field technique. Interestingly, a pronounced field dependence of the free carrier generation for all blends is found, with the field dependence being stronger without the additive. Also, the bimolecular recombination coefficient for both blends is rather high and increases with decreasing internal field which we suggest to be caused by a negative field dependence of mobility. The additive speeds up charge extraction which is rationalized by the threefold increase in mobility. By fluorine attachment within the electron deficient subunit of PCPDTBT, a new polymer F-PCPDTBT is designed. This new material is characterized by a stronger tendency to aggregate as compared to non-fluorinated PCPDTBT. Our measurements show that for F-PCPDTBT:PCBM blends the charge carrier generation becomes more efficient and the field-dependence of free charge carrier generation is weakened. The stronger tendency to aggregate induced by the fluorination also leads to increased polymer rich domains, accompanied in a threefold reduction in the non-geminate recombination coefficient at conditions of open circuit. The size of the polymer domains is nicely correlated to the field-dependence of charge generation and the Langevin reduction factor, which highlights the importance of the domain size and domain purity for efficient charge carrier generation. In total, fluorination of PCPDTBT causes the PCE to increase from 3.6 to 6.1% due to enhanced fill factor, short circuit current and open circuit voltage. Further optimization of the blend ratio, active layer thickness, and polymer molecular weight resulted in 6.6% efficiency for F-PCPDTBT:PC70BM solar cells. Interestingly, the double fluorinated version 2F-PCPDTBT exhibited poorer FF despite a further reduction of geminate and non-geminate recombination losses. To further analyze this finding, a new technique is developed that measures the effective extraction mobility under charge carrier densities and electrical fields comparable to solar cell operation conditions. This method involves the bias enhanced charge extraction technique. With the knowledge of the carrier density under different electrical field and illumination conditions, a conclusive picture of the changes in charge carrier dynamics leading to differences in the fill factor upon fluorination of PCPDTBT is attained. The more efficient charge generation and reduced recombination with fluorination is counterbalanced by a decreased extraction mobility. Thus, the highest fill factor of 60% and efficiency of 6.6% is reached for F-PCPDTBT blends, while 2F-PCPDTBT blends have only moderate fill factors of 54% caused by the lower effective extraction mobility, limiting the efficiency to 6.5%. To understand the details of the charge generation mechanism and the related losses, we evaluated the yield and field-dependence of free charge generation using time delayed collection field in combination with sensitive measurements of the external quantum efficiency and absorption coefficients for a variety of blends. Importantly, both the yield and field-dependence of free charge generation is found to be unaffected by excitation energy, including direct charge transfer excitation below the optical band gap. To access the non-detectable absorption at energies of the relaxed charge transfer emission, the absorption was reconstructed from the CT emission, induced via the recombination of thermalized charges in electroluminescence. For a variety of blends, the quantum yield at energies of charge transfer emission was identical to excitations with energies well above the optical band-gap. Thus, the generation proceeds via the split-up of the thermalized charge transfer states in working solar cells. Further measurements were conducted on blends with fine-tuned energy levels and similar blend morphologies by using different fullerene derivatives. A direct correlation between the efficiency of free carrier generation and the energy difference of the relaxed charge transfer state relative to the energy of the charge separated state is found. These findings open up new guidelines for future material design as new high efficiency materials require a minimum energetic offset between charge transfer and the charge separated state while keeping the HOMO level (and LUMO level) difference between donor and acceptor as small as possible. N2 - Die Effizienz von organischen Mischsolarzellen ist in den letzten Jahren durch die Entwicklung neuer halbleitender Materialen beträchtlich gestiegen. Die besten organischen Mischsolarzellen zeigen heute sehr effiziente Ladungsgeneration. Dennoch ist die genaue Funktionsweise der fundamentalen Ladungsgenerationsschritte nicht bis ins Detail verstanden. Zur weiteren Steigerung der Wirkungsgrade und für die kommerzielle Nutzung organischer Mischsolarzellen, sind ein übergreifendes Verständnis der Funktionsweise und die Entwicklung neuer Messmethoden unumgänglich. Die vorliegende Arbeit ist auf diese Fragestellung fokussiert: die Arbeit soll helfen, fundierte Kenntnisse der Ladungsträgererzeugung, der Rekombination und der Extraktion freier Ladungsträger in organischen Mischsolarzellen zu erlangen. Zuerst wurde der Fokus auf Mischsolarzellen mit dem Polymer PCPDTBT gelegt. Dieses Polymer durchmischt stark mit dem Fulleren-Derivat PCBM. Durch Verwendung eines Lösungsmitteladditives kann die Phasenentmischung und damit der Wirkungsgrad deutlich gesteigert werden. Die Generations- und Rekombinationsprozesse wurden mittels zeitverzögerter Sammelfeld-Methode untersucht. Dabei wurde zum ersten Mal eine signifikante Feldabhängigkeit der Ladungsträger-erzeugung entdeckt. Interessanterweise korreliert diese Feldabhängigkeit mit der Domänengröße also dem Grad der Entmischung. In größeren und reineren Polymerphasen ist die Feldabhängigkeit kleiner und die Extraktion verbessert, was zum höheren Wirkungsgrad führt. In einem weiteren Schritt wurde untersucht, wie sich die Fluorinierung des Polymers PCPDTBT auf das Bauteilverhalten auswirkt. Durch Fluorinierung des Polymer-Rückgrats von PCPDTBT wurden zum einen die Energieniveaus abgesenkt, ohne dass sich das Absorptionsverhalten geändert hat. Zum anderen wurde die Phasenentmischung beeinflusst. Mit Fluorinierung entstehen größere, reinere und kristallinere Polymerphasen. Dadurch wird die Generation der Ladungsträger effizienter und die Rekombination stärker unterdrückt. Eindeutige Korrelationen zwischen Phasengröße und Generationseffizienz konnten hierbei gefunden werden. Insgesamt steigt die Bauteileffizienz bei Verwendung von fluoriniertem PCPDTBT von 3.6 auf 6.1% bei gleicher Prozessierung. Durch weitere Optimierung konnte die Effizienz auf 6.6% für fluoriniertes PCPDTBT gesteigert werden. Eine di-Fluorinierung von PCPDTBT limitiert die Bauteileffizienz, speziell den Füll Faktor, trotz der Entstehung noch reinerer Polymerphasen. Eine genauere Analyse der Extraktionseffizienz mittels der genauen Bestimmung der Gleichgewichts-Ladungsträgerdichte für verschiedenen Beleuchtungs- und Feldsituationen zeigte, dass die Fluorinierung die Effizienz der Extraktion deutlich absenkt und dadurch bei di-Fluorinierung die Rekombinationsverluste im Bauteil trotz verlangsamter Rekombination ansteigen. Um weitere fundierte Kenntnisse der Ladungsgeneration zu gewinnen, wurde die Ladungsgeneration für verschiedene Gemische mit veränderten Energieniveaus in Abhängigkeit der Anregungsenergie untersucht. Dabei wurde die wichtige Kenntnis erlangt, dass die Photonenenergie, unabhängig von der Lage der Energieniveaus, keinen Einfluss auf die Effizienz der Generation hat und somit die Bildung freier Ladungsträger aus relaxierten Transferzuständen erfolgt. Dadurch ergeben sich neue Leitlinien für zukünftige Materialeigenschaften mit optimierten Wirkungsgraden. KW - organic solar cells KW - bulk heterojunction KW - charge carrier dynamics KW - charge generation KW - non geminate recombination KW - Generierung von Ladungsträgern KW - nicht geminale Rekombination KW - Extraktion KW - Polymer KW - Fulleren Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-72285 ER - TY - THES A1 - Schubert, Marcel T1 - Elementary processes in layers of electron transporting Donor-acceptor copolymers : investigation of charge transport and application to organic solar cells T1 - Elementare Prozesse in Schichten elektronen-transportierender Donator-Akzeptor-Copolymere : Untersuchung des Ladungstransports und Anwendung in Organischen Solarzellen N2 - Donor-acceptor (D-A) copolymers have revolutionized the field of organic electronics over the last decade. Comprised of a electron rich and an electron deficient molecular unit, these copolymers facilitate the systematic modification of the material's optoelectronic properties. The ability to tune the optical band gap and to optimize the molecular frontier orbitals as well as the manifold of structural sites that enable chemical modifications has created a tremendous variety of copolymer structures. Today, these materials reach or even exceed the performance of amorphous inorganic semiconductors. Most impressively, the charge carrier mobility of D-A copolymers has been pushed to the technologically important value of 10 cm^{2}V^{-1}s^{-1}. Furthermore, owed to their enormous variability they are the material of choice for the donor component in organic solar cells, which have recently surpassed the efficiency threshold of 10%. Because of the great number of available D-A copolymers and due to their fast chemical evolution, there is a significant lack of understanding of the fundamental physical properties of these materials. Furthermore, the complex chemical and electronic structure of D-A copolymers in combination with their semi-crystalline morphology impede a straightforward identification of the microscopic origin of their superior performance. In this thesis, two aspects of prototype D-A copolymers were analysed. These are the investigation of electron transport in several copolymers and the application of low band gap copolymers as acceptor component in organic solar cells. In the first part, the investigation of a series of chemically modified fluorene-based copolymers is presented. The charge carrier mobility varies strongly between the different derivatives, although only moderate structural changes on the copolymers structure were made. Furthermore, rather unusual photocurrent transients were observed for one of the copolymers. Numerical simulations of the experimental results reveal that this behavior arises from a severe trapping of electrons in an exponential distribution of trap states. Based on the comparison of simulation and experiment, the general impact of charge carrier trapping on the shape of photo-CELIV and time-of-flight transients is discussed. In addition, the high performance naphthalenediimide (NDI)-based copolymer P(NDI2OD-T2) was characterized. It is shown that the copolymer posses one of the highest electron mobilities reported so far, which makes it attractive to be used as the electron accepting component in organic photovoltaic cells.\par Solar cells were prepared from two NDI-containing copolymers, blended with the hole transporting polymer P3HT. I demonstrate that the use of appropriate, high boiling point solvents can significantly increase the power conversion efficiency of these devices. Spectroscopic studies reveal that the pre-aggregation of the copolymers is suppressed in these solvents, which has a strong impact on the blend morphology. Finally, a systematic study of P3HT:P(NDI2OD-T2) blends is presented, which quantifies the processes that limit the efficiency of devices. The major loss channel for excited states was determined by transient and steady state spectroscopic investigations: the majority of initially generated electron-hole pairs is annihilated by an ultrafast geminate recombination process. Furthermore, exciton self-trapping in P(NDI2OD-T2) domains account for an additional reduction of the efficiency. The correlation of the photocurrent to microscopic morphology parameters was used to disclose the factors that limit the charge generation efficiency. Our results suggest that the orientation of the donor and acceptor crystallites relative to each other represents the main factor that determines the free charge carrier yield in this material system. This provides an explanation for the overall low efficiencies that are generally observed in all-polymer solar cells. N2 - Donator-Akzeptor (D-A) Copolymere haben das Feld der organischen Elektronik revolutioniert. Bestehend aus einer elektronen-reichen und einer elektronen-armen molekularen Einheit,ermöglichen diese Polymere die systematische Anpassung ihrer optischen und elektronischen Eigenschaften. Zu diesen zählen insbesondere die optische Bandlücke und die Lage der Energiezustände. Dabei lassen sie sich sehr vielseitig chemisch modifizieren, was zu einer imensen Anzahl an unterschiedlichen Polymerstrukturen geführt hat. Dies hat entscheidend dazu beigetragen, dass D-A-Copolymere heute in Bezug auf ihren Ladungstransport die Effizienz von anorganischen Halbleitern erreichen oder bereits übetreffen. Des Weiteren lassen sich diese Materialien auch hervorragend in Organischen Solarzellen verwenden, welche jüngst eine Effizienz von über 10% überschritten haben. Als Folge der beträchtlichen Anzahl an unterschiedlichen D-A-Copolymeren konnte das physikalische Verständnis ihrer Eigenschaften bisher nicht mit dieser rasanten Entwicklung Schritt halten. Dies liegt nicht zuletzt an der komplexen chemischen und mikroskopischen Struktur im Film, in welchem die Polymere in einem teil-kristallinen Zustand vorliegen. Um ein besseres Verständnis der grundlegenden Funktionsweise zu erlangen, habe ich in meiner Arbeit sowohl den Ladungstransport als auch die photovoltaischen Eigenschaften einer Reihe von prototypischen, elektronen-transportierenden D-A Copolymeren beleuchtet. Im ersten Teil wurden Copolymere mit geringfügigen chemischen Variationen untersucht. Diese Variationen führen zu einer starken Änderung des Ladungstransportverhaltens. Besonders auffällig waren hier die Ergebnisse eines Polymers, welches sehr ungewöhnliche transiente Strom-Charakteristiken zeigte. Die nähere Untersuchung ergab, dass in diesem Material elektrisch aktive Fallenzustände existieren. Dieser Effekt wurde dann benutzt um den Einfluss solcher Fallen auf transiente Messung im Allgemeinen zu beschreiben. Zusätzlich wurde der Elektronentransport in einem neuartigen Copolymer untersucht, welche die bis dato größte gemesse Elektronenmobilität für konjugierte Polymere zeigte. Darauf basierend wurde versucht, die neuartigen Copolymere als Akzeptoren in Organischen Solarzellen zu implementieren. Die Optimierung dieser Zellen erwies sich jedoch als schwierig, konnte aber erreicht werden, indem die Lösungseigenschaften der Copolymere untersucht und systematisch gesteuert wurden. Im Weiteren werden umfangreiche Untersuchungen zu den relevanten Verlustprozessen gezeigt. Besonders hervorzuheben ist hier die Beobachtung, dass hohe Effizienzen nur bei einer coplanaren Packung der Donator/Akzeptor-Kristalle erreicht werden können. Diese Struktureigenschaft wird hier zum ersten Mal beschrieben und stellt einen wichtigen Erkenntnisgewinn zum Verständnis von Polymersolarzellen dar. KW - Organische Solarzellen KW - Ladungstransport KW - Donator-Akzeptor-Copolymere KW - Alternative Akzeptorpolymere KW - Polymer-Kristalle KW - organic solar cells KW - charge transport KW - Donor-acceptor copolymers KW - alternative electron acceptors KW - polymer crystal orientation Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-70791 ER -