TY - GEN A1 - Müller, Bernd Randolf A1 - Kupsch, Andreas A1 - Laquai, Rene A1 - Nellesen, Jens A1 - Tillmann, Wolfgang A1 - Kasperovich, Galina A1 - Bruno, Giovanni T1 - Microstructure Characterisation of Advanced Materials via 2D and 3D X-Ray Refraction Techniques T2 - Materials Science Forum N2 - 3D imaging techniques have an enormous potential to understand the microstructure, its evolution, and its link to mechanical, thermal, and transport properties. In this conference paper we report the use of a powerful, yet not so wide-spread, set of X-ray techniques based on refraction effects. X-ray refraction allows determining internal specific surface (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with a nanometric detectability. We demonstrate showcases of ceramics and composite materials, where microstructural parameters could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. We present in situ analysis of the damage evolution in an Al/Al2O3 metal matrix composite during tensile load and the identification of void formation (different kinds of defects, particularly unsintered powder hidden in pores, and small inhomogeneity’s like cracks) in Ti64 parts produced by selective laser melting using synchrotron X-ray refraction radiography and tomography. KW - X-ray refraction KW - radiography KW - tomography KW - synchrotron X-ray refraction radiography KW - CT KW - microscopy KW - creep KW - porosity KW - damage evolution KW - additive manufacturing KW - metal matrix composite Y1 - 2018 SN - 978-3-0357-1208-7 U6 - https://doi.org/10.4028/www.scientific.net/MSF.941.2401 SN - 0255-5476 VL - 941 SP - 2401 EP - 2406 PB - Trans Tech Publications Ltd CY - Zurich ER - TY - THES A1 - Walczak, Ralf T1 - Molecular design of nitrogen-doped nanoporous noble carbon materials for gas adsorption T1 - Molekulares Design Stickstoffdotierter, Nanoporöser, und Edler Kohlenstoffmaterialien für Gasadsorption N2 - In den modernen Gesellschaften führt ein stetig steigender Energiebedarf zu dem zunehmenden Verbrauch fossiler Brennstoffe wie Kohle, Öl, und Gas. Die Verbrennung dieser kohlenstoffbasierten Brennstoffe führt unweigerlich zur Freisetzung von Treibhausgasen, vor allem von CO2. Die CO2 Aufnahme unmittelbar bei den Verbrennungsanlagen oder direkt aus der Luft, zusammen mit Regulierung von CO2 produzierenden Energiesektoren (z.B. Kühlanlagen), können den CO2 Ausstoß reduzieren. Allerdings führen insbesondere bei der CO2 Aufnahme die geringen CO2 Konzentrationen und die Aufnahme konkurrierender Gase zu niedrigen CO2 Kapazitäten und Selektivitäten. Das Zusammenspiel der Gastmoleküle mit porösen Materialien ist dabei essentiell. Poröse Kohlenstoffmaterialien besitzen attraktive Eigenschaften, unter anderem elektrische Leitfähigkeit, einstellbare Porosität, als auch chemische und thermische Stabilität. Allerdings führt die zu geringe Polarisierbarkeit dieser Materialien zu einer geringen Affinität zu polaren Molekülen (z.B. CO2, H2O, oder NH3). Diese Affinität kann durch den Einbau von Stickstoff erhöht werden. Solche Materialien sind oft „edler“ als reine Kohlenstoffe, dies bedeutet, dass sie eher oxidierend wirken, als selbst oxidiert zu werden. Die Problematik besteht darin, einen hohen und gleichmäßig verteilten Stickstoffgehalt in das Kohlenstoffgerüst einzubauen. Die Zielsetzung dieser Dissertation ist die Erforschung neuer Synthesewege für stickstoffdotierte edle Kohlenstoffmaterialien und die Entwicklung eines grundlegenden Verständnisses für deren Anwendung in Gasadsorption und elektrochemischer Energiespeicherung. Es wurde eine templatfreie Synthese für stickstoffreiche, edle, und mikroporöse Kohlenstoffmaterialien durch direkte Kondensation eines stickstoffreichen organischen Moleküls als Vorläufer erarbeitet. Dadurch konnten Materialien mit hohen Adsorptionskapazitäten für H2O und CO2 bei niedrigen Konzentrationen und moderate CO2/N2 Selektivitäten erzielt werden. Um die CO2/N2 Selektivitäten zu verbessern, wurden mittels der Einstellung des Kondensationsgrades die molekulare Struktur und Porosität der Kohlenstoffmaterialien kontrolliert. Diese Materialien besitzen die Eigenschaften eines molekularen Siebs für CO2 über N2, das zu herausragenden CO2/N2 Selektivitäten führt. Der ultrahydrophile Charakter der Porenoberflächen und die kleinen Mikroporen dieser Kohlenstoffmaterialien ermöglichen grundlegende Untersuchungen für die Wechselwirkungen mit Molekülen die polarer sind als CO2, nämlich H2O und NH3. Eine weitere Reihe stickstoffdotierter Kohlenstoffmaterialien wurde durch Kondensation eines konjugierten mikroporösen Polymers synthetisiert und deren strukturelle Besonderheiten als Anodenmaterial für die Natriumionen Batterie untersucht. Diese Dissertation leistet einen Beitrag zur Erforschung stickstoffdotierter Kohlenstoffmaterialien und deren Wechselwirkungen mit verschiedenen Gastmolekülen. N2 - The growing energy demand of the modern economies leads to the increased consumption of fossil fuels in form of coal, oil, and natural gases, as the mains sources. The combustion of these carbon-based fossil fuels is inevitably producing greenhouse gases, especially CO2. Approaches to tackle the CO2 problem are to capture it from the combustion sources or directly from air, as well as to avoid CO2 production in energy consuming sources (e.g., in the refrigeration sector). In the former, relatively low CO2 concentrations and competitive adsorption of other gases is often leading to low CO2 capacities and selectivities. In both approaches, the interaction of gas molecules with porous materials plays a key role. Porous carbon materials possess unique properties including electric conductivity, tunable porosity, as well as thermal and chemical stability. Nevertheless, pristine carbon materials offer weak polarity and thus low CO2 affinity. This can be overcome by nitrogen doping, which enhances the affinity of carbon materials towards acidic or polar guest molecules (e.g., CO2, H2O, or NH3). In contrast to heteroatom-free materials, such carbon materials are in most cases “noble”, that is, they oxidize other matter rather than being oxidized due to the very positive working potential of their electrons. The challenging task here is to achieve homogenous distribution of significant nitrogen content with similar bonding motives throughout the carbon framework and a uniform pore size/distribution to maximize host-guest interactions. The aim of this thesis is the development of novel synthesis pathways towards nitrogen-doped nanoporous noble carbon materials with precise design on a molecular level and understanding of their structure-related performance in energy and environmental applications, namely gas adsorption and electrochemical energy storage. A template-free synthesis approach towards nitrogen-doped noble microporous carbon materials with high pyrazinic nitrogen content and C2N-type stoichiometry was established via thermal condensation of a hexaazatriphenylene derivative. The materials exhibited high uptake of guest molecules, such as H2O and CO2 at low concentrations, as well as moderate CO2/N2 selectivities. In the following step, the CO2/N2 selectivity was enhanced towards molecular sieving of CO2 via kinetic size exclusion of N2. The precise control over the condensation degree, and thus, atomic construction and porosity of the resulting materials led to remarkable CO2/N2 selectivities, CO2 capacities, and heat of CO2 adsorption. The ultrahydrophilic nature of the pore walls and the narrow microporosity of these carbon materials served as ideal basis for the investigation of interface effects with more polar guest molecules than CO2, namely H2O and NH3. H2O vapor physisorption measurements, as well as NH3-temperature programmed desorption and thermal response measurements showed exceptionally high affinity towards H2O vapor and NH3 gas. Another series of nitrogen-doped carbon materials was synthesized by direct condensation of a pyrazine-fused conjugated microporous polymer and their structure-related performance in electrochemical energy storage, namely as anode materials for sodium-ion battery, was investigated. All in all, the findings in this thesis exemplify the value of molecularly designed nitrogen-doped carbon materials with remarkable heteroatom content implemented as well-defined structure motives. The simultaneous adjustment of the porosity renders these materials suitable candidates for fundamental studies about the interactions between nitrogen-doped carbon materials and different guest species. KW - carbon materials KW - nitrogen-doped KW - gas adsorption KW - porosity KW - Porösität KW - Gasadsorption KW - Stickstoffdotiert KW - Kohlenstoffmaterialien Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-435241 ER - TY - JOUR A1 - Behl, Marc A1 - Zhao, Qian A1 - Lendlein, Andreas T1 - Glucose-responsive shape-memory cryogels JF - Journal of materials research : JMR N2 - Boronic ester bonds can be reversibly formed between phenylboronic acid (PBA) and triol moieties. Here, we aim at a glucose-induced shape-memory effect by implementing such bonds as temporary netpoints, which are cleavable by glucose and by minimizing the volume change upon stimulation by a porous cryogel structure. The polymer system consisted of a semi-interpenetrating network (semi-IPN) architecture, in which the triol moieties were part of the permanent network and the PBA moieties were located in the linear polymer diffused into the semi-IPN. In an alkaline medium (pH = 10), the swelling ratio was approximately 35, independent of C-glu varied between 0 and 300 mg/dL. In bending experiments, shape fixity R-f approximate to 80% and shape recovery R-r approximate to 100% from five programming/recovery cycles could be determined. R-r was a function of C-glu in the range from 0 to 300 mg/dL, which accords with the fluctuation range of C-glu in human blood. In this way, the shape-memory hydrogels could play a role in future diabetes treatment options. KW - shape memory KW - polymer KW - porosity Y1 - 2020 U6 - https://doi.org/10.1557/jmr.2020.204 SN - 0884-2914 SN - 2044-5326 VL - 35 IS - 18 SP - 2396 EP - 2404 PB - Springer CY - Berlin ER - TY - JOUR A1 - Léonard, Fabien A1 - Zhang, Zhen A1 - Krebs, Holger A1 - Bruno, Giovanni T1 - Structural and morphological quantitative 3D characterisation of ammonium nitrate prills by X-ray computed tomography JF - Materials N2 - The mixture of ammonium nitrate (AN) prills and fuel oil (FO), usually referred to as ANFO, is extensively used in the mining industry as a bulk explosive. One of the major performance predictors of ANFO mixtures is the fuel oil retention, which is itself governed by the complex pore structure of the AN prills. In this study, we present how X-ray computed tomography (XCT), and the associated advanced data processing workflow, can be used to fully characterise the structure and morphology of AN prills. We show that structural parameters such as volume fraction of the different phases and morphological parameters such as specific surface area and shape factor can be reliably extracted from the XCT data, and that there is a good agreement with the measured oil retention values. Importantly, oil retention measurements (qualifying the efficiency of ANFO as explosives) correlate well with the specific surface area determined by XCT. XCT can therefore be employed non-destructively; it can accurately evaluate and characterise porosity in ammonium nitrate prills, and even predict their efficiency. KW - ANFO KW - explosives KW - specific surface area KW - porosity KW - XCT KW - data processing Y1 - 2020 U6 - https://doi.org/10.3390/ma13051230 SN - 1996-1944 VL - 13 IS - 5 PB - MDPI CY - Basel ER - TY - JOUR A1 - Zhang, Yan-qiu A1 - Guo, Zeng-hui A1 - Chen, Dai-zhao T1 - Porosity distribution in cyclic dolomites of the Lower Qiulitag Group (Upper Cambrian) in northwestern Tarim Basin, China JF - China geology N2 - Increasing interests in hydrocarbon resources at depths have drawn greater attentions to the deeply-buried carbonate reservoirs in the Tarim Basin in China. In this study, the cyclic dolomite rocks of Upper Cambrian Lower Qiulitag Group from four outcrop sections in northwestern Tarim Basin were selected to investigate and evaluate the petrophysical properties in relation to depositional facies and cyclicity. The Lower Qiulitag Group includes ten lithofacies, which were deposited in intermediate to shallow subtidal, restricted shallow subtidal, intertidal, and supratidal environments on a carbonate ramp system. These lithofacies are vertically stacked into repeated shallowing-upward, meter-scale cycles which are further grouped into six third-order depositional sequences (Sq1 to Sq6). There are variable types of pore spaces in the Lower Qiulitag Group dolomite rocks, including interparticle, intraparticle, and fenestral pores of primary origin, inter crystal, and vuggy pores of late diagenetic modification. The porosity in the dolomites is generally facies-selective as that the microbially-originated thrombolites and stromatolites generally yield a relatively high porosity. In contrast, the high-energy ooidal grainstones generally have very low porosity. In this case, the microbialite-based peritidal cycles and peritidal cycle-dominated highstand (or regressive) successions have relatively high volumes of pore spaces, although highly fluctuating (or vertical inhomogeneous). Accordingly, the grainstone-based subtidal cycles and subtidal cycle-dominated transgressive successions generally yield extremely low porosity. This scenario indicates that porosity development and preservation in the thick dolomite successions are primarily controlled by depositional facies which were influenced by sea-level fluctuations of different orders and later diagenetic overprinting. KW - Dolomites KW - porosity KW - cyclicity KW - Upper Cambrian KW - stromatolite KW - microbial KW - build up KW - oil-gas basin KW - oil-gas exploration engineering KW - Tarim Basin KW - China Y1 - 2020 UR - http://en.cgsjournals.com/zgdzdcqkw-data/zgdzyw/2020/3/PDF/cg2020026.pdf SN - 2096-5192 SN - 2589-9430 VL - 3 IS - 3 SP - 425 EP - 444 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kojda, Danny A1 - Hofmann, Tommy A1 - Gostkowska-Lekner, Natalia Katarzyna A1 - Habicht, Klaus T1 - Characterization and modeling of the temperature-dependent thermal conductivity in sintered porous silicon-aluminum nanomaterials JF - Nano research N2 - Nanostructured silicon and silicon-aluminum compounds are synthesized by a novel synthesis strategy based on spark plasma sintering (SPS) of silicon nanopowder, mesoporous silicon (pSi), and aluminum nanopowder. The interplay of metal-assisted crystallization and inherent porosity is exploited to largely suppress thermal conductivity. Morphology and temperature-dependent thermal conductivity studies allow us to elucidate the impact of porosity and nanostructure on the macroscopic heat transport. Analytic electron microscopy along with quantitative image analysis is applied to characterize the sample morphology in terms of domain size and interpore distance distributions. We demonstrate that nanostructured domains and high porosity can be maintained in densified mesoporous silicon samples. In contrast, strong grain growth is observed for sintered nanopowders under similar sintering conditions. We observe that aluminum agglomerations induce local grain growth, while aluminum diffusion is observed in porous silicon and dispersed nanoparticles. A detailed analysis of the measured thermal conductivity between 300 and 773 K allows us to distinguish the effect of reduced thermal conductivity caused by porosity from the reduction induced by phonon scattering at nanosized domains. With a modified Landauer/Lundstrom approach the relative thermal conductivity and the scattering length are extracted. The relative thermal conductivity confirms the applicability of Kirkpatrick's effective medium theory. The extracted scattering lengths are in excellent agreement with the harmonic mean of log-normal distributed domain sizes and the interpore distances combined by Matthiessen's rule. KW - thermal conductivity KW - mesoporous silicon KW - porosity KW - spark plasma KW - sintering KW - nanoscale modeling Y1 - 2022 U6 - https://doi.org/10.1007/s12274-022-4123-y SN - 1998-0124 SN - 1998-0000 VL - 15 IS - 6 SP - 5663 EP - 5670 PB - Tsinghua Univ. Press CY - Beijing ER -