TY - THES A1 - Lettau, Kristian T1 - Katalytische molekular geprägte Polymere : Herstellung und Anwendung in einem Thermistor T1 - Catalytically molecular imprinted polymers : synthesis and application in a thermistor N2 - Biomakromoleküle sind in der Natur für viele Abläufe in lebenden Organismen verantwortlich. Dies reicht vom Aufbau der extrazellulären Matrix und dem Cytoskelett über die Erkennung von Botenstoffen durch Rezeptoren bis hin zur Katalyse der verschiedensten Reaktionen in den Zellen selbst. Diese Aufgaben werden zum größten Teil von Proteinen übernommen, und besonders das spezifische Erkennen der Interaktionspartner ist für alle diese Moleküle äußerst wichtig, um eine fehlerfreie Funktion zu gewährleisten. Als Alternative zur evolutiven Erzeugung von optimalen Bindern und Katalysatoren auf der Basis von Aminosäuren und Nukleotiden wurden von Wulff, Shea und Mosbach synthetische molekular geprägte Polymere (molecularly imprinted polymers, MIPs) konzipiert. Das Prinzip dieser künstlichen Erkennungselemente beruht auf der Tatsache, dass sich funktionelle Monomere spezifisch um eine Schablone (Templat) anordnen. Werden diese Monomere dann vernetzend polymerisiert, entsteht ein Polymer mit molekularen Kavitäten, in denen die Funktionalitäten komplementär zum Templat fixiert sind. Dadurch ist die selektive Bindung des Templats in diese Kavitäten möglich. Aufgrund ihrer hohen chemischen und thermischen Stabilität und ihrer geringen Kosten haben “bio-inspirierte” molekular geprägte Polymere das Potential, biologische Erkennungselemente in der Affinitätschromatographie sowie in Biosensoren und Biochips zu ersetzen. Trotz einiger publizierter Sensorkonfigurationen steht der große Durchbruch noch aus. Ein Hindernis für Routineanwendungen ist die Signalgenerierung bei Bindung des Analyten an das Polymer. Eine Möglichkeit für die markerfreie Detektion ist die Benutzung von Kalorimetern, die Bindungs- oder Reaktionswärmen direkt messen können. In der Enzymtechnologie wird der Enzym-Thermistor für diesen Zweck eingesetzt, da enzymatische Reaktionen eine Enthalpie in einer Größenordnung von 5 – 100 kJ/mol besitzen. In dieser Arbeit wird die Herstellung von katalytisch geprägten Polymeren nach dem Verfahren des Oberflächenprägens erstmalig beschrieben. Die Methode zur Immobilisierung des Templats auf der Oberfläche von porösem Kieselgel sowie die Polymerzusammensetzung wurden optimiert. Weiter wird die Evaluation der katalytischen Eigenschaften über einen optischen Test, sowie das erste Mal die Kombination eines kalorimetrischen Transduktors – des Thermistors – mit der Analyterkennung durch ein katalytisch aktives MIP gezeigt. Bei diesen Messungen konnte zum ersten Mal gleichzeitig die Bindung/Desorption, sowie die katalytische Umwandlung des Substrats durch konzentrationsabhängige Wärmesignale nachgewiesen werden. N2 - Bio macromolecules are responsible in nature for many reactions in living organisms. This reaches from the structure of the extra cellular matrix and the cytoskeleton over the recognition of ligands by receptors up to the catalysis of the most diverse reactions in the cells themselves. These tasks are taken over to the largest part by proteins, and particularly specific recognizing of the interaction partners is extremely important for all these molecules, in order to ensure an error free function. As alternative to the evolutionary production of optimal binders and catalysts on the basis of amino acids and nucleotides, synthetic molecularly imprinted polymer (MIPs) were invented by Wulff, Shea and Moosbach. The principle of these artificial recognition elements is based on the fact that functional monomers specifically arrange themselves around a template. If these monomers are copolymerized with crosslinking monomers, a polymer with molecular cavities is created, in which the functionalities are fixed complementary to the template. Thus the selective binding of the template is possible into these cavities. Due to their high chemical and thermal stability and their small costs "bioinspired" molecularly imprinted polymers have the potential to replace biological recognition elements in affinity chromatography as well as in biosensors and biochips. Despite some published sensor configurations the large break-through is still pending. An obstacle for routine application of is the signal generation on connection of the analyte to the polymer. A possibility for marker-free detection is the use of calorimeters, which can measure heats of reaction or adsorption directly. In enzyme technology the enzyme thermistor is used for this purpose, as enzymatic reactions possess enthalpies in an order of 5 - 100 kJ/mol. In this work the production of catalytically imprinted polymers is described for the first time by the procedure of surface imprinting. The method for immobilization of the template on the surface of porous silicagel as well as the polymer composition were optimized. The evaluation of the catalytic characteristics is shown by an optical test, as well as the first time the combination of a calorimetric transducer - the thermistor - with the analyte recognition by a catalytically active MIP. With these measurements for the first time the binding/desorption, as well as the catalytic transformation of the substrate could be proven at the same time by concentration-dependent heat signals. KW - Katalyse KW - molekular geprägte Polymere KW - Kalorimetrie KW - Enzymmodelle KW - Biosensoren KW - catalysis KW - molecularly imprinted polymers KW - calorimetry KW - enzyme models KW - biosensors Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-14804 ER - TY - THES A1 - Braun, Max T1 - Heterogeneous Catalysis for the Conversion of Fructose to Chemicals and Fuel in a Continuous Flow Process T1 - Umsetzung von Fruktose zu Chemikalien und Treibstoff mittels heterogener Katalysatoren in einem kontinuierlichen Prozess N2 - Die Umsetzung von Zucker (Kohlenhydrate) in einem kontinuierlichen Prozess eröffnet Möglichkeiten der Synthese diverser Chemikalien und Treibstoff aus erneuerbaren Ressourcen, welche heute überwiegend aus fossilen Quellen stammen. Passend zum Konzept der Bioraffinerie und der „grünen Chemie“, liegt der Fokus dieser Arbeit auf der Umsetzung von in Ethanol gelöster Fruktose in einem kontinuierlichen Verfahren, mit Hilfe eigens entwickelter heterogener Katalysatoren. Die Dehydratisierung von Fruktose wird mit einem heterogenen Säurekatalysator realisiert, während die Folgeprodukte mittels einer Hydrodesoxygenierung umgesetzt werden. Für den zweiten Schritt kommen Metallkatalysatoren auf Basis von Nickel und Wolframcarbid (WC) zum Einsatz, wodurch der Einsatz teurer Edelmetalle vermieden werden kann. Hauptprodukte des zweistufigen Verfahrens sind 2,5-Dimethylfuran (DMF) und Ethyllevulinat (EL). Beide Moleküle sind vielversprechende alternative Treibstoffe, bzw. können gebräuchlichen Treibstoffen beigemischt werden, um deren Einsatz zu reduzieren und schrittweise zu substituieren. Alternativ können die Zwischenprodukte der Dehydratisierung, sowie DMF und EL weiter zu Chemikalien umgesetzt werden, welche in der Polymersynthese, als Lösungsmittel oder als Grundchemikalien eingesetzt werden können. Die Entwicklung der jeweiligen Katalysatoren für Dehydratisierungs- und Hydrodesoxygenierungsreaktionen erfolgt auf Basis von karbonisierter Biomasse, sowie Wolframcarbid. Die jeweiligen Reaktivitäten werden durch Standardreaktionen getestet, wobei sich Wolframcarbid in Nanopartikelform, in Kombination mit Wasserstoff als sehr aktiv erwiesen hat. Der selbst entwickelte aktivierte Kohlenstoff, das kommerzielle Amberlyst 15, sowie Wolframcarbid mit zusätzlichen Nickel-Nanopartikeln werden für weiterführende Reaktionen in einem kontinuierlichen Prozess herangezogen und kombiniert. Um den Umsatz von Fruktose zu DMF in einer „zwei Reaktoren Anlage“ zu ermöglichen, wird eine Erweiterung eines kommerziellen Reaktorsystems um einen weiteren Reaktor vorgenommen. Die Verweilzeit in der Reaktoranlage beträgt somit ca. 14 Minuten, wobei 11 Minuten auf die erste Säule (Dehydratisierung) und 3 Minuten auf die zweite Säule (Hydrodesoxygenierung) entfallen. In diesem kontinuierlichen und zweistufigen System lassen sich Ausbeuten von 38.5 % DMF und 47 % EL erzielen. Ein kontinuierlicher Lauf von sieben Stunden zeigt die Stabilität der eingesetzten Katalysatoren, auch wenn eine geringe Deaktivierung des Dehydratisierungskatalysators beobachtet werden kann. Der Ni@WC Katalysator zeigte hingegen keine Abnahme der Nickel Konzentration und somit kommt es zu keiner Auswaschung des Metalls. Das gebildete EL wurde hingegen nicht umgesetzt und verbleibt unverändert in Lösung. Das zweistufige System wurde schließlich in einem Mischkatalysatorsystem kombiniert, wobei auf aktivierten und sulfonierten Kohlenstoff zurückgegriffen wurde. Dieser zeigte bereits eine Transferhydrodesoxygenierungsaktivität. Diese Beobachtung ist deshalb bemerkenswert, da erst seit kurzem bekannt ist, dass Graphenstrukturen an sich katalytisch aktiv sein können. Um diese Aktivität weiter zu steigern, wurde der aktivierte Kohlenstoff mit 10 wt% Ni@WC gemischt, sodass beide Katalysatoren in einer Säule vorliegen. Die ursprünglichen 2 % DMF Ausbeute mit reinem aktivierten Kohlenstoff können somit auf 12 % gesteigert werden, da das Folgeprodukt EL hierbei vermieden wird und das Zwischenprodukt „HMF Derivat“ direkt zu DMF weiter reagieren kann. Dieses Ergebnis zeigt das Potential der „ein Reaktor Umsetzung“, weshalb eine kontinuierliche Durchflussreaktoranlage im Litermaßstab als Scale-Up des vorhergehenden Labormaßstabs realisiert wurde. Der 800 mm x 28.5 mm Reaktor bedient eine maximale Flussrate von 50 mL min-1, Drücke von 100 bar und Temperaturen bis zu 500 °C. N2 - The valorization of carbohydrates is one of the most promising fields in green chemistry, as it enables to produce bulk chemicals and fuels out of renewable and abundant resources, instead of further exploiting fossil feedstocks. The focus in this thesis is the conversion of fructose, using dehydration and hydrodeoxygenation reactions. The main goal is to find an easy continuous process, including the solubility of the sugar in a green solvent, the conversion over a solid acid as well as over a metal@tungsten carbide catalyst. At the beginning of this thesis, solid acid catalysts are synthesized by using carbohydrate material like glucose and starch at high temperatures (up to 600 °C). Additionally a third carbon is synthesized, using an activation method based on Ca(OH)2. After carbonization and further sulfonation, using fuming sulfuric acid, the three resulting catalysts are characterized together with sulfonated carbon black and Amberlyst 15 as references. In order to test all solid acid catalysts in reaction, a 250 mm x 4.6 mm stainless steel column is used as a fixed-bed continuous reactor. The temperature (110 °C to 250 °C) and residence time (2 to 30 minutes) is varied, and a direct relationship between contact time and selectivity is determined. The reaction mechanism, as well as the product distribution is showing a dehydration step of fructose towards 5-hydroxymethylfurfural (HMF). These furan-ring molecules are considered as “sleeping giants”, due to the possibility of using them as fuel, but also for upgrading them to chemicals like terephthalic acid or p-xylene. Consecutive reactions are producing levulinic acid, as well as condensation products with ethanol and formic acid. The activated carbon is additionally showing a 2 % yield of 2,5-Dimethylfuran (DMF) production, pointing towards the extraordinary properties of this catalyst. Without a metal catalyst present, what is normally necessary for hydrogenation reactions, a transferhydrogenation (with formic acid) is observed. The active catalyst was therefore carbon itself, what activated the hydrogen on its surface. This phenomenon was just very rarely observed so far. Expensive noble metals are the material of choice, when it comes to hydrogenation reactions nowadays and cheaper alternatives are necessary. By postulating a similar electronic structure of tungsten carbide (WC) to platinum by Lewy and Boudart, research is focusing on the replacement of Pt. The production of nano-sized tungsten carbide particles (7.5 ± 2.5 nm, 70 m2 g-1) is enabled by the so called “urea glass route” and its catalytic performances are compared to commercial material. It is shown, that the activity is strongly dependent on the size of the particles as well as the surface area. Nano-sized tungsten carbide is showing activity for hydrogenation reactions under mild conditions (maximum 150 °C, 30 bar). This material therefore opens up new possibilities for replacing the rare and expensive platinum with tungsten carbide based catalysts. Additionally different metal nanoparticles of palladium, copper and nickel are deposited on top of WC to further promote its reactivity. The nickel nanoparticles are strongly connected to WC and showed the best activity as well as selectivity for upgrading HMF with hydrodeoxygenation. The Ni@WC is not leaching and is showing very good hydrodeoxygenation properties with DMF yields up to 90 percent. Copper@WC is not showing good activity and palladium@WC enables undesired consecutive reactions, hydrogenating the furan ring system. In order to enable the upgrade of fructose to DMF directly in a continuous system, the current H CUBE Pro TM hydrogenation system is customized with a second reaction column. A 250 mm x 4.6 mm stainless steel reactor column is connected ahead of the hydrogen insertion, enabling the dehydration of fructose to HMF derivatives, before pumping these products into the second column for hydrogenation. The overall residence time in the two column reactor system is 14 minutes. The overall results are an almost full conversion with a yield of 38.5 % DMF and 47 % yield of EL. The main disadvantage is the formation of higher mass products, so called humins, which start depositing on top of the catalysts, blocking their active sites. In general it can be stated, that a two column system goes along with a higher investment as well as more maintenance costs, compared to a one column catalytic approach. To develop a catalyst, which is on the one hand able to dehydrate as well as hydrodeoxygenate the reactants, is aimed for at the last part of the thesis. The activated carbon however shows already activity for hydrodeoxygenation without any metal present and offers itself therefore as an alternative to overcome the temperature instability of Amberlyst 15 (max. 120 °C) for a combined DMF production directly from fructose. The activity for the upgrade to DMF is increased from 2 % to 12 % DMF yield in one mixed continuous column. In order to scale up the entire one column approach, an 800 mm x 28.5 mm inner diameter column was planned and manufactured. The system is scaled up and assembled, whereas this flow reactor system is able to be run with 50 mL min-1 maximum flow rate, to stand a pressure of maximum 100 bar and be heated to around 500 °C. The tubing and connections, as well as the used devices are planned according to be safe and easy in use. The scaled-up approach offers a reaction column 120 times bigger (510 ml) then the first extension of the commercial system. This further extension offers the possibility of ranging between 1 and 1000 mL min-1, making it possible to use the approach in pilot plant applications. KW - Biorefinery KW - Catalysis KW - Hydroxymethylfurfural KW - Upgrade of Fructose KW - Bioraffinerie KW - Katalyse KW - Hydroxymethylfurfural KW - Aufarbeitung von Fruktose Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-410370 ER - TY - THES A1 - Karras, Manfred T1 - Synthesis of enantiomerically pure helical aromatics such as NHC ligands and their use in asymmetric catalysis T1 - Die Synthese von enantiomerenreinen helikalen Aromaten wie NHC Liganden und deren Anwendung in asymmetrischer Katalyse N2 - Diese Arbeit beschäftigt sich mit der enantiomerenreinen Synthese helikaler, aromatischer Verbindungen. Verschiedene Verbindungen dieses Typs wurden erfolgreich hergestellt und charakterisiert. Desweiteren wurden einige der neuen Verbindungen in Übergangsmetallkomplexe eingebaut und diese dann als Katalysatoren für Metathese und Kreuzkupplungen getestet. Einer der getesteten Katalysatoren zeigte vielversprechende Ergebnisse in der asymmetrischen Olefinmetathese. Die Struktur des neuen Katalysators wurde untersucht. Anhand der Struktur des neuen Katalysators wurden Rückschlüsse auf einen möglichen Mechanismus gezogen. N2 - Various ways of preparing enantiomerically pure 2-amino[6]helicene derivatives were explored. Ni(0) mediated cyclotrimerization of enantiopure triynes provided (M)- and (P)-7,8-bis(p-tolyl)hexahelicene-2-amine in >99% ee as well as its benzoderivative in >99% ee. The stereocontrol was found to be inefficient for a 2- aminobenzo[6]helicene congener with an embedded five-membered ring. Helically chiral imidazolium salts bearing one or two helicene moieties have been synthesized and applied in enantioselective [2+2+2] cyclotrimerization catalyzed by an in situ formed Ni(0)-NHC complex. The synthesis of the first helically chiral Pd- and Ru-NHC complexes and their application in enantioselective catalysis was demonstrated. The latter shows promising results in enantioselective olefin metathesis reactions. A mechanistic proposal for asymmetric ring closing metathesis is provided. KW - helicene KW - catalysis KW - NHC KW - asymmetric KW - Helicen KW - Katalyse KW - NHC KW - asymmetrisch Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-421497 ER - TY - THES A1 - Lama, Sandy M. G. T1 - Functionalization of Porous Carbon Materials with Heteroatoms and Application as Supports in Industrial Heterogeneous Catalysis T1 - Funktionalisierung von porösen Kohlenstoffmaterialien mit Heteroatomen und Anwendung als Träger in der industriellen heterogenen Katalyse N2 - Due to a challenging population growth and environmental changes, a need for new routes to provide required chemicals for human necessities arises. An effective solution discussed in this thesis is industrial heterogeneous catalysis. The development of an advanced industrial heterogeneous catalyst is investigated herein by considering porous carbon nano-material as supports and modifying their surface chemistry structure with heteroatoms. Such modifications showed a significant influence on the performance of the catalyst and provided a deeper insight regarding the interaction between the surface structure of the catalyst and the surrounding phase. This thesis contributes to the few present studies about heteroatoms effect on the catalyst performance and emphasizes on the importance of understanding surface structure functionalization in a catalyst in different phases (liquid and gaseous) and for different reactions (hydrogenolysis, oxidation, and hydrogenation/ polymerization). Herein, the heteroatoms utilized for the modifications are hydrogen (H), oxygen (O), and nitrogen (N). The heteroatoms effect on the metal particle size, on the polarity of the support/ the catalyst, on the catalytic performance (activity, selectivity, and stability), and on the interaction with the surrounding phase has been explored. First hierarchical porous carbon nanomaterials functionalized with heteroatoms (N) is synthesized and applied as supports for nickel nanoparticles for hydrogenolysis process of kraft lignin in liquid phase. This reaction has been performed in batch and flow reactors for three different catalysts, two of comparable hierarchical porosity, yet one is modified with N and the other is not, and a third is a prepared catalyst from a commercial carbon support. The reaction production and analyses show that the catalysts with hierarchical porosity perform catalytically much better than in presence of a commercial carbon support with lower surface area. Moreover, the modification with N-heteroatoms enhanced the catalytic performance because the heteroatom modified porous carbon material with nickel nanoparticles catalyst (Ni-NDC) performed highest among the other catalysts. In the flow reactor, Ni-NDC selectively degraded the ether bonds (β-O-4) in kraft lignin with an activity of 2.2 x10^-4 mg lignin mg Ni-1 s-1 for 50 h at 350°C and 3.5 mL min-1 flow, providing ~99 % conversion to shorter chained chemicals (mainly guaiacol derivatives). Then, the functionalization of carbon surface was further studied in selective oxidation of glucose to gluconic acid using < 1 wt. % of gold (Au) deposited on the previously-mentioned synthesized carbon (C) supports with different functionalities (Au-CGlucose, Au-CGlucose-H, Au-CGlucose-O, Au-CGlucoseamine). Except for Au-CGlucose-O, the other catalysts achieved full glucose conversion within 40-120 min and 100% selectivity towards gluconic acid with a maximum activity of 1.5 molGlucose molAu-1 s-1 in an aqueous phase at 45 °C and pH 9. Each heteroatom influenced the polarity of the carbon differently, affecting by that the deposition of Au on the support and thus the activity of the catalyst and its selectivity. The heteroatom effect was further investigated in a gas phase. The Fischer-Tropsch reaction was applied to convert synthetic gas (CO and H2) to short olefins and paraffins using surface-functionalized carbon nanotubes (CNTs) with heteroatoms as supports for ion (Fe) deposition in presence and absence of promoters (Na and S). The results showed the promoted Fe-CNT doped with nitrogen catalyst to be stable up to 180 h and selective to the formation of olefins (~ 47 %) and paraffins (~6 %) with a conversion of CO ~ 92 % at a maximum activity of 94 *10^-5 mol CO g Fe-1 s-1. The more information given regarding this topic can open wide range of applications not only in catalysis, but in other approaches as well. In conclusion, incorporation of heteroatoms can be the next approach for an advanced industrial heterogeneous catalyst, but also for other applications (e.g. electrocatalysis, gas adsorption, or supercapacitors). N2 - Herausforderungen wie Bevölkerungszuwachs und Umweltveränderungen erfordern neue Wege, chemische Substanzen zu erzeugen, um menschliche Anforderungen zu befriedigen. Eine mögliche effektive Lösung dafür, welche in dieser Arbeit diskutiert wird ist die industrielle heterogene Katalyse. Es werden unter dem Einsatz poröser Kohlenstoffträger neue industrielle Katalysatoren untersucht und entwickelt wobei die Oberflächenstruktur dieser Trägermaterialien mit Heteroatomen modifiziert wird. Diese Modifikationen zeigten einen signifikanten Einfluss auf die Eigenschaften der Katalysatoren und erlaubten Rückschlüsse hinsichtlich der Interaktion zwischen Katalysatoroberfläche und umgebender Phase. Die vorliegende Arbeit trägt zu einigen wenigen existierenden Studien bei die sich mit den Einflüssen solcher Heteroatome auf Katalysatoren beschäftigen. Es wird versucht, die Wichtigkeit dieser Oberflächeneigenschaften in Reaktionen (Hydrogenolyse, Oxidation, Hydrierung/ Polymerisation) in verschiedenen Phasen (flüssig oder gasförmig) zu verstehen. Die für die Modifikationen eingesetzten Heteroatome sind Wasserstoff (H), Sauerstoff (O) und Stickstoff (N). Ihr Effekt auf die Größe der Metallpartikel, die Polarität der Träger bzw. Katalysatoren, die eigentlichen katalytischen Eigenschaften und die Interaktion mit der umgebenden Phase wurde untersucht. Zuerst wurden hierarchisch poröse Kohlenstoffmaterialien hergestellt, die mit Stickstoff als Heteroatome funktionalisiert wurden. Diese wurden als Trägermaterialien für Nickel-Nanopartikel in der Hydrogenolyse von Kraft Lignin in flüssiger Phase eingesetzt. Diese Reaktion wurde mit drei unterschiedlichen Katalysatoren in Batch- und Flussreaktoren durchgeführt. Zwei der Katalysatoren hatten vergleichbare hierarchische Porosität. Einer davon war mit Heteroatomen funktionalisiert, einer dagegen nicht. Ein dritter Katalysator wurde mit einem kommerziell erhältlichen Kohlenstoffmaterial hergestellt. Die Reaktion zeigte, dass die Katalysatoren mit hierarchischer Porosität deutlich bessere Eigenschaften zeigen als das kommerzielle Trägermaterial mit geringerer Oberfläche. Darüber hinaus zeigte sich, dass die Modifizierung mit Stickstoffatomen die katalytischen Eigenschaften verbessert, da das modifizierte Kohlenstoffmaterial mit den Nickelpartikeln (Ni-NDC) die besten Ergebnisse aller untersuchten Katalysatoren zeigte. Im Durchflussreaktor wurden von Ni-NDC die Etherbindungen des Kraft Lignins (β-O-4) selektiv mit einer Aktivität von 2.2 x10^-4 mg lignin mg Ni-1 s-1 für 50 h bei 99% Umsatz zu kurzkettigeren Strukturen (hauptsächlich Guajakol-Derivat) gespalten. Außerdem wurde der Einfluss der Funktionalisierung der Kohlenstoffoberfläche in der selektiven Oxidation von Glucose zu Gluconsäure mit 1 Gew.% Gold (Au) auf den vorher angesprochenen Kohlenstoffträgermaterialien mit unterschiedlichen Oberflächenfunktionalitäten (Au-CGlucose, Au-CGlucose-H, Au-CGlucose-O, Au-CGlucoseamine) untersucht. Mit Ausnahme von Au-CGlucose-O erreichten alle Katalysatoren innerhalb von 40-120 min 100% Glucose Umsatz bei 100%iger Selektivität zu Gluconsäure und einer maximalen katalytischen Aktivität von 1.5 molGlucose molAu-1 s-1 in wässriger Phase bei 45°C und pH 9. Die unterschiedlichen Heteroatome wirkten sich unterschiedlich auf die Polarität der Kohlenstoffe und damit auch auf die Abscheidung der Goldpartikel auf die Trägermaterialien und die Katalysatoraktivität und -selektivität aus. Der Einfluss der Heteroatome wurde außerdem in einer Gasphasenreaktion untersucht. Die Fischer-Tropsch Reaktion kam zum Einsatz um Synthesegas (CO und H2) mit Hilfe von Katalysatoren bestehend aus Eisen (Fe) auf Heteroatomfunktionalisierten Kohlenstoffnanoröhrchen (engl. Carbon nanotubes, CNTs) in Gegenwart und Abwesenheit von Promotoren (Na und S) zu kurzkettigen Olefinen und Paraffinen umzuwandeln. Die Ergebnisse zeigten dass die Fe-CNT Katalysatoren mit Promotoren und stickstoffdotierten Trägern bis zu 180 h stabil waren und Olefine (~ 47 %) sowie Paraffine (~6 %) mit guten Selektivitäten bei einem CO Umsatz von 92% und einer maximalen Aktivität von 94 *10^-5 mol CO gFe-1 s-1 hergestellt werden konnten. Je mehr Informationen zu diesem Thema zur Verfügung gestellt werden, kann dies zu einer großen Bandbreite von Anwendungen nicht nur in der Katalyse, sondern auch in anderen Ansätzen beitragen. Zusammenfassend kann der Einbau von Heteroatomen der nächste Ansatz für einen fortgeschrittenen industriellen heterogenen Katalysator sein, aber auch für andere Anwendungen (z.B. Elektrokatalyse, Gasadsorption oder Superkondensatoren). KW - catalysis KW - carbon material KW - carbon supports KW - glucose oxidation KW - Kraft lignin hydrogenolysis KW - Fischer-Tropsch Synthesis KW - Syngas Hydrogenation KW - gold-carbon catalysts KW - nickel-carbon catalysts KW - iron-carbon nanotube catalysts KW - hierarchical porosity KW - heteroatom modification KW - catalyst functionalization KW - Katalyse KW - Kohlenstoffmaterial KW - Kohlenstoffträger KW - Glukoseoxidation KW - Kraftlignin KW - Hydrogenolyse KW - Fischer-Tropsch-Synthese KW - Syngashydrierung KW - Gold-Kohlenstoff-Katalysatoren KW - Nickel-Kohlenstoff-Katalysatoren KW - Eisen-Kohlenstoff-Nanoröhrchen-Katalysatoren KW - hierarchische Porosität KW - Heteroatom-Modifikation KW - Funktionalisierung von Katalysatoren Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-415797 ER -