TY - JOUR A1 - Farkas, Márton Pál A1 - Yoon, Jeoung Seok A1 - Zang, Arno A1 - Zimmermann, Günter A1 - Stephansson, Ove A1 - Lemon, Michael A1 - Danko, Gyula T1 - Effect of foliation and fluid viscosity on hydraulic fracturing tests in mica schists investigated using distinct element modeling and field data JF - Rock Mechanics and Rock Engineering N2 - Several hydraulic fracturing tests were performed in boreholes located in central Hungary in order to determine the in-situ stress for a geological site investigation. At a depth of about 540m, the observed pressure versus time curves in mica schist with low dip angle foliation shows atypical pressure versus time results. After each pressurization cycle, the fracture breakdown pressure in the first fracturing cycle is lower than the refracturing or reopening pressure in the subsequent pressurizations. It is assumed that the viscosity of the drilling mud and observed foliation of the mica schist have a significant influence on the pressure values. In order to study this problem, numerical modeling was performed using the distinct element code particle flow code, which has been proven to be a valuable tool to investigate rock engineering problems such as hydraulic fracturing. The two-dimensional version of the code applied in this study can simulate hydro-mechanically coupled fluid flow in crystalline rock with low porosity and pre-existing fractures. In this study, the effect of foliation angle and fluid viscosity on the peak pressure is tested. The atypical characteristics of the pressure behaviour are interpreted so that mud with higher viscosity penetrates the sub-horizontal foliation plane, blocks the plane of weakness and makes the partly opened fracture tight and increase the pore pressure which decreases slowly with time. We see this viscous blocking effect as one explanation for the observed increase in fracture reopening pressure in subsequent pressurization cycles. KW - Hydraulic fracturing KW - Stress measurement KW - Particle flow code KW - Hydro-mechanical coupling KW - Microcrack KW - Viscous blocking Y1 - 2019 U6 - https://doi.org/10.1007/s00603-018-1598-7 SN - 0723-2632 SN - 1434-453X VL - 52 IS - 2 SP - 555 EP - 574 PB - Springer CY - Wien ER - TY - JOUR A1 - Hofmann, Hannes A1 - Blöcher, Guido A1 - Zang, Arno T1 - Special issue on rock fracturing and fault activation BT - experiments and models selected papers presented at the 13th EURO-Conference on rock physics and geomechanics - the Gueguen Conference Held on 2-6 September 2019 in Potsdam, Germany JF - Rock mechanics and rock engineering Y1 - 2021 U6 - https://doi.org/10.1007/s00603-021-02635-4 SN - 0723-2632 SN - 1434-453X VL - 54 IS - 10 SP - 5149 EP - 5153 PB - Springer CY - Wien ER - TY - JOUR A1 - Hofmann, Hannes A1 - Zimmermann, Günter A1 - Farkas, Márton Pál A1 - Huenges, Ernst A1 - Zang, Arno A1 - Leonhardt, Maria A1 - Kwiatek, Grzegorz A1 - Martinez-Garzon, Patricia A1 - Bohnhoff, Marco A1 - Min, Ki-Bok A1 - Fokker, Peter A1 - Westaway, Rob A1 - Bethmann, Falko A1 - Meier, Peter A1 - Yoon, Kern Shin A1 - Choi, JaiWon A1 - Lee, Tae Jong A1 - Kim, Kwang Yeom T1 - First field application of cyclic soft stimulation at the Pohang Enhanced Geothermal System site in Korea JF - Geophysical journal international N2 - Large-magnitude fluid-injection induced seismic events are a potential risk for geothermal energy developments worldwide. One potential risk mitigation measure is the application of cyclic injection schemes. After validation at small (laboratory) and meso (mine) scale, the concept has now been applied for the first time at field scale at the Pohang Enhanced Geothermal System (EGS) site in Korea. From 7 August until 14 August 2017 a total of 1756 m(3) of surface water was injected into Pohang well PX-1 at flow rates between 1 and 10 l s(-1), with a maximum wellhead pressure (WHP) of 22.8 MPa, according to a site-specific cyclic soft stimulation schedule and traffic light system. A total of 52 induced microearthquakes were detected in real-time during and shortly after the injection, the largest of M-w 1.9. After that event a total of 1771 m(3) of water was produced back from the well over roughly 1 month, during which time no larger-magnitude seismic event was observed. The hydraulic data set exhibits pressure-dependent injectivity increase with fracture opening between 15 and 17 MPa WHP, but no significant permanent transmissivity increase was observed. The maximum magnitude of the induced seismicity during the stimulation period was below the target threshold of M-w 2.0 and additional knowledge about the stimulated reservoir was gained. Additionally, the technical feasibility of cyclic injection at field scale was evaluated. The major factors that limited the maximum earthquake magnitude are believed to be: limiting the injected net fluid volume, flowback after the occurrence of the largest induced seismic event, using a cyclic injection scheme, the application of a traffic light system, and including a priori information from previous investigations and operations in the treatment design. KW - Cyclic soft stimulation (CSS) KW - induced seismicity KW - risk mitigation KW - enhanced geothermal systems (EGS) KW - granite KW - Pohang (Korea) Y1 - 2019 U6 - https://doi.org/10.1093/gji/ggz058 SN - 0956-540X SN - 1365-246X VL - 217 IS - 2 SP - 926 EP - 949 PB - Oxford Univ. Press CY - Oxford ER - TY - JOUR A1 - Kwiatek, Grzegorz A1 - Martinez-Garzon, Patricia A1 - Plenkers, K. A1 - Leonhardt, Maria A1 - Zang, Arno A1 - von Specht, Sebastian A1 - Dresen, Georg A1 - Bohnhoff, Marco T1 - Insights into complex subdecimeter fracturing processes occurring during a water injection experiment at depth in Aspo Hard Rock Laboratory, Sweden JF - Journal of geophysical research : Solid earth N2 - We investigate the source characteristics of picoseismicity (M-w < -2) recorded during a hydraulic fracturing in situ experiment performed in the underground Aspo Hard Rock Laboratory, Sweden. The experiment consisted of six stimulations driven by three different water injection schemes and was performed inside a 28-m-long, horizontal borehole located at 410-m depth. The fracturing processes were monitored with a variety of seismic networks including broadband seismometers, geophones, high-frequency accelerometers, and acoustic emission sensors thereby covering a wide frequency band between 0.01 and 100,000Hz. Here we study the high-frequency signals with dominant frequencies exceeding 1000 Hz. The combined seismic network allowed for detection and detailed analysis of 196 small-scale seismic events with moment magnitudes M-W < -3.5 (source sizes of decimeter scale) that occurred solely during the stimulations and shortly after. The double-difference relocated hypocenter catalog as well as source parameters were used to study the physical characteristics of the induced seismicity and then compared to the stimulation parameters. We observe a spatiotemporal migration of the picoseismic events away and toward the injection intervals in direct correlation with changes in the hydraulic energy (product of fluid injection pressure and injection rate). We find that the total radiated seismic energy is extremely low with respect to the product of injected fluid volume and pressure (hydraulic energy). The radiated seismic energy correlates well with the hydraulic energy rate. The obtained fault plane solutions for particularly well-characterized events signify the reactivation of preexisting rock defects under influence of increased pore fluid pressure on fault plane orientations in good correspondence with the local stress field orientation. KW - induced seismicity KW - fracking KW - picoseismicity KW - seismomechanics KW - source parameters KW - maximum magnitude Y1 - 2018 U6 - https://doi.org/10.1029/2017JB014715 SN - 2169-9313 SN - 2169-9356 VL - 123 IS - 8 SP - 6616 EP - 6635 PB - American Geophysical Union CY - Washington ER - TY - JOUR A1 - Niemz, Peter A1 - Cesca, Simone A1 - Heimann, Sebastian A1 - Grigoli, Francesco A1 - von Specht, Sebastian A1 - Hammer, Conny A1 - Zang, Arno A1 - Dahm, Torsten T1 - Full-waveform-based characterization of acoustic emission activity in a mine-scale experiment BT - a comparison of conventional and advanced hydraulic fracturing schemes JF - Geophysical journal international / the Royal Astronomical Society, the Deutsche Geophysikalische Gesellschaft and the European Geophysical Society N2 - Understanding fracturing processes and the hydromechanical relation to induced seismicity is a key question for enhanced geothermal systems (EGS). Commonly massive fluid injection, predominately causing hydroshearing, are used in large-scale EGS but also hydraulic fracturing approaches were discussed. To evaluate the applicability of hydraulic fracturing techniques in EGS, six in situ, multistage hydraulic fracturing experiments with three different injection schemes were performed under controlled conditions in crystalline rock at the Aspo Hard Rock Laboratory (Sweden). During the experiments the near-field ground motion was continuously recorded by 11 piezoelectric borehole sensors with a sampling rate of 1 MHz. The sensor network covered a volume of 30x30x30 m around a horizontal, 28-m-long injection borehole at a depth of 410 m. To extract and characterize massive, induced, high-frequency acoustic emission (AE) activity from continuous recordings, a semi-automated workflow was developed relying on full waveform based detection, classification and location procedures. The approach extended the AE catalogue from 196 triggered events in previous studies to more than 19600 located AEs. The enhanced catalogue, for the first time, allows a detailed analysis of induced seismicity during single hydraulic fracturing experiments, including the individual fracturing stages and the comparison between injection schemes. Beside the detailed study of the spatio-temporal patterns, event clusters and the growth of seismic clouds, we estimate relative magnitudes and b-values of AEs for conventional, cyclic progressive and dynamic pulse injection schemes, the latter two being fatigue hydraulic fracturing techniques. While the conventional fracturing leads to AE patterns clustered in planar regions, indicating the generation of a single main fracture plane, the cyclic progressive injection scheme results in a more diffuse, cloud-like AE distribution, indicating the activation of a more complex fracture network. For a given amount of hydraulic energy (pressure multiplied by injected volume) pumped into the system, the cyclic progressive scheme is characterized by a lower rate of seismicity, lower maximum magnitudes and significantly larger b-values, implying an increased number of small events relative to the large ones. To our knowledge, this is the first direct comparison of high resolution seismicity in a mine-scale experiment induced by different hydraulic fracturing schemes. KW - Fracture and flow KW - Spatial analysis KW - Statistical methods KW - Time-series analysis KW - Induced seismicity Y1 - 2020 U6 - https://doi.org/10.1093/gji/ggaa127 SN - 0955-419X SN - 1365-246X VL - 222 IS - 1 SP - 189 EP - 206 PB - Oxford Univ. Press CY - Oxford ER - TY - JOUR A1 - Niemz, Peter A1 - Dahm, Torsten A1 - Milkereit, Claus A1 - Cesca, Simone A1 - Petersen, Gesa Maria A1 - Zang, Arno T1 - Insights into hydraulic fracture growth gained from a joint analysis of seismometer-derived tilt signals and scoustic emissions JF - Journal of geophysical research : Solid earth N2 - Hydraulic fracturing is performed to enhance rock permeability, for example, in the frame of geothermal energy production or shale gas exploitation, and can potentially trigger induced seismicity. The tracking of increased permeabilities and the fracturing extent is often based on the microseismic event distribution within the stimulated rock volume, but it is debated whether the microseismic activity adequately depicts the fracture formation. We are able to record tilt signals that appear as long-period transients (<180 s) on two broadband seismometers installed close (17-72 m) to newly formed, meter-scale hydraulic fractures. With this observation, we can overcome the limitations of the microseismic monitoring alone and verify the fracture mapping. Our analysis for the first time combines a catalog of previously analyzed acoustic emissions ([AEs] durations of 20 ms), indirectly mapping the fractures, with unique tilt signals, that provide independent, direct insights into the deformation of the rock. The analysis allows to identify different phases of the fracturing process including the (re)opening, growth, and aftergrowth of fractures. Further, it helps to differentiate between the formation of complex fracture networks and single macrofractures, and it validates the AE fracture mapping. Our findings contribute to a better understanding of the fracturing processes, which may help to reduce fluid-injection-induced seismicity and validate efficient fracture formation.
Plain Language Summary Hydraulic fracturing (HF) describes the opening of fractures in rocks by injecting fluids under high pressure. The new fractures not only can facilitate the extraction of shale gas but can also be used to heat up water in the subsurface in enhanced geothermal systems, a corner stone of renewable energy production. The fracture formation is inherently accompanied by small, nonfelt earthquakes (microseismic events). Occasionally, larger events felt by the population can be induced by the subsurface operations. Avoiding such events is important for the acceptance of HF operations and requires a detailed knowledge about the fracture formation. We jointly analyze two very different data sets recorded during mine-scale HF experiments: (a) the tilting of the ground caused by the opening of the fractures, as recorded by broadband seismometers-usually deployed for earthquake monitoring-installed close to the experiments and (b) a catalog of acoustic emissions, seismic signals of few milliseconds emitted by tiny cracks around the forming hydraulic fracture. The novel joint analysis allows to characterize the fracturing processes in greater detail, contributing to the understanding of the physical processes, which may help to understand fluid-injection-induced seismicity and validate the formation of hydraulic fractures. KW - hydraulic fracturing KW - fracture growth KW - tilt KW - acoustic emissions KW - injections KW - broadband seismometer Y1 - 2021 U6 - https://doi.org/10.1029/2021JB023057 SN - 2169-9313 SN - 2169-9356 VL - 126 IS - 12 PB - American Geophysical Union CY - Washington ER - TY - JOUR A1 - Reigber, Christoph A1 - Wassermann, Joachim A1 - Scherbaum, Frank A1 - Dresen, Georg A1 - Zang, Arno A1 - Altenberger, Uwe A1 - Rahmstorf, Stefan A1 - Klein, Armin A1 - Oberhänsli, Roland A1 - Herzig, Reinhard T1 - Portal = Vulkane, Erdbeben, Klima: Der Planet Erde birgt viele Geheimnisse BT - Die Potsdamer Universitätszeitung N2 - Aus dem Inhalt: - Vulkane, Erdbeben, Klima: Der Planet Erde birgt viele Geheimnisse - Eine Entdeckungsreise durch die Uni Potsdam auf CD-ROM - Gewitter im Gehirn - Herr der Pflanzen: Wolfgang Pifrement T3 - Portal: Das Potsdamer Universitätsmagazin - 01-02/2002 Y1 - 2002 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-439544 SN - 1618-6893 IS - 01-02/2002 ER - TY - JOUR A1 - von Specht, Sebastian A1 - Heidbach, Oliver A1 - Cotton, Fabrice Pierre A1 - Zang, Arno T1 - Uncertainty reduction of stress tensor inversion with data-driven catalogue selection JF - Geophysical journal international N2 - The selection of earthquake focal mechanisms (FMs) for stress tensor inversion (STI) is commonly done on a spatial basis, that is, hypocentres. However, this selection approach may include data that are undesired, for example, by mixing events that are caused by different stress tensors when for the STI a single stress tensor is assumed. Due to the significant increase of FM data in the past decades, objective data-driven data selection is feasible, allowing more refined FM catalogues that avoid these issues and provide data weights for the STI routines. We present the application of angular classification with expectation-maximization (ACE) as a tool for data selection. ACE identifies clusters of FM without a priori information. The identified clusters can be used for the classification of the style-of-faulting and as weights of the FM data. We demonstrate that ACE effectively selects data that can be associated with a single stress tensor. Two application examples are given for weighted STI from South America. We use the resulting clusters and weights as a priori information for an STI for these regions and show that uncertainties of the stress tensor estimates are reduced significantly. KW - Inverse Theory KW - Statistical Methods KW - Seismicity KW - tectonics KW - Kinematics of crustal KW - mantle deformation Y1 - 2018 U6 - https://doi.org/10.1093/gji/ggy240 SN - 0956-540X SN - 1365-246X VL - 214 IS - 3 SP - 2250 EP - 2263 PB - Oxford Univ. Press CY - Oxford ER - TY - THES A1 - Zang, Arno T1 - Akustische Emissionen beim Sprödbruch von Gestein Y1 - 1997 ER - TY - BOOK A1 - Zang, Arno A1 - Stephansson, Ove T1 - Stress field of the earth's crust Y1 - 2010 SN - 978-1-402-08443-0 U6 - https://doi.org/10.1007/978-1-4020-8444-7 PB - Springer Science+Business Media B.V CY - Dordrecht ER -