TY - THES A1 - Martínez Guajardo, Alejandro T1 - New zwitterionic polymers for antifouling applications T1 - Neue zwitterionische Polymere für Antifouling-Anwendungen N2 - The remarkable antifouling properties of zwitterionic polymers in controlled environments are often counteracted by their delicate mechanical stability. In order to improve the mechanical stabilities of zwitterionic hydrogels, the effect of increased crosslinker densities was thus explored. In a first approach, terpolymers of zwitterionic monomer 3-[N -2(methacryloyloxy)ethyl-N,N-dimethyl]ammonio propane-1-sulfonate (SPE), hydrophobic monomer butyl methacrylate (BMA), and photo-crosslinker 2-(4-benzoylphenoxy)ethyl methacrylate (BPEMA) were synthesized. Thin hydrogel coatings of the copolymers were then produced and photo-crosslinked. Studies of the swollen hydrogel films showed that not only the mechanical stability but also, unexpectedly, the antifouling properties were improved by the presence of hydrophobic BMA units in the terpolymers. Based on the positive results shown by the amphiphilic terpolymers and in order to further test the impact that hydrophobicity has on both the antifouling properties of zwitterionic hydrogels and on their mechanical stability, a new amphiphilic zwitterionic methacrylic monomer, 3-((2-(methacryloyloxy)hexyl)dimethylammonio)propane-1-sulfonate (M1), was synthesized in good yields in a multistep synthesis. Homopolymers of M1 were obtained by free-radical polymerization. Similarly, terpolymers of M1, zwitterionic monomer SPE, and photo-crosslinker BPEMA were synthesized by free-radical copolymerization and thoroughly characterized, including its solubilities in selected solvents. Also, a new family of vinyl amide zwitterionic monomomers, namely 3-(dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propane-1-sulfonate (M2), 4-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)butane-1-sulfonate (M3), and 3-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propyl sulfate (M4), together with the new photo-crosslinker 4-benzoyl-N-vinylbenzamide (M5) that is well-suited for copolymerization with vinylamides, are introduced within the scope of the present work. The monomers are synthesized with good yields developing a multistep synthesis. Homopolymers of the new vinyl amide zwitterionic monomers are obtained by free-radical polymerization and thoroughly characterized. From the solubility tests, it is remarkable that the homopolymers produced are fully soluble in water, evidence of their high hydrophilicity. Copolymerization of the vinyl amide zwitterionic monomers, M2, M3, and M4 with the vinyl amide photo-crosslinker M5 proved to require very specific polymerization conditions. Nevertheless, copolymers were successfully obtained by free-radical copolymerization under appropriate conditions. Moreover, in an attempt to mitigate the intrinsic hydrophobicity introduced in the copolymers by the photo-crosslinkers, and based on the proven affinity of quaternized diallylamines to copolymerize with vinyl amides, a new quaternized diallylamine sulfobetaine photo-crosslinker 3-(diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propane-1-sulfonate (M6) is synthesized. However, despite a priori promising copolymerization suitability, copolymerization with the vinyl amide zwitterionic monomers could not be achieved. N2 - Die hervorragenden Antifouling-Eigenschaften zwitterionischer Polymere in kontrollierten Bedingungen werden häufig durch ihre geringe mechanische Stabilität beeinträchtigt. Um die mechanische Eigenschaften zwitterionischer Hydrogele zu verbessern, wurde daher der Effekt einer erhöhten Vernetzungsdichte untersucht. In einem ersten Ansatz wurden Terpolymere aus dem zwitterionischen Monomer 3-[N -2(Methacryloyloxy)ethyl-N,N-dimethyl]ammonio propan-1-sulfonat (SPE), dem hydrophoben Monomer Butylmethacrylat (BMA) und dem Photovernetzer 2-(4-Benzoylphenoxy)ethylmethacrylat (BPEMA) synthetisiert. Daraufhin wurden dünne Beschichtungen der Copolymere hergestellt und photovernetzt. Die Untersuchung der gequollenen Hydrogelfilme zeigte, dass nicht nur die mechanischen Eigenschaften, sondern überraschenderweise auch die Antifouling-Eigenschaften der Hydrogele durch den Einbau von hydrophoben BMA-Einheiten in die Terpolymere verbessert wurden. Aufgrund der positiven Ergebnisse der amphiphilen Terpolymere und um die Auswirkungen der Hydrophobie sowohl auf die Antifouling- als auch auf die mechanische Eigenschaften der zwitterionischen Hydrogele zu testen, wurde ein neues amphiphiles zwitterionisches Methacrylat, nämlich 3-((2-(Methacryloyloxy)hexyl)dimethylammonio)propan-1-sulfonat (M1), in guter Ausbeute synthetisiert. Homopolymere von M1 wurden durch radikalische Polymerisation erhalten. In ähnlicher Weise wurden Terpolymere aus M1, dem zwitterionischen Monomer SPE und dem Photovernetzer BPEMA durch radikalische Copolymerisation synthetisiert und gründlich charakterisiert, einschließlich ihrer Löslichkeiten in ausgewählten Lösungsmitteln. Außerdem wurde im Rahmen der vorliegenden Arbeit eine neue Familie von zwitterionischen Vinylamidmonomeren, nämlich 3-(Dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propan-1-sulfonat (M2), 4-(Dimethyl(2-(N -vinylacetamido)ethyl)ammonio)butan-1-sulfonat (M3) und 3-(Dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propylsulfat (M4), zusammen mit einem geeigneten Vinylamid-Photovernetzer, nämlich 4-Benzoyl-N -vinylbenzamide (M5) entwickelt. Die Monomere wurden in einer Mehrstufen-Synthese mit guten Ausbeuten synthetisiert. Homopolymere der neuen zwitterionischen Vinylamidmonomere wurden durch radikalische Polymerisation erhalten und eingehend charakterisiert. Die Löslichkeitstests zeigen, dass die hergestellten Homopolymere bemerkenswerterweise vollständig in reinem Wasser löslich sind, was ihre hohe Hydrophilie beweist. Die Copolymerisation der zwitterionischen Vinylamidmonomere M2, M3 und M4 mit dem Vinylamid-Photovernetzer M5 erwies sich als schwierig. Die Copolymere lassen sich dennoch unter sehr spezifische Bedingungen durch radikalische Copolymerisation herstellen. Des Weiteren, um die durch die Photovernetzer in die Copolymere eingebrachte inhärente Hydrophobie zu mindern und aufgrund ihrer nachgewiesenen Affinität zur Copolymerisation mit Vinylamiden, wurde ein neuer quaternisierter Diallylaminsulfobetain-Photovernetzer 3-(Diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propan-1-sulfonat (M6) synthetisiert. Trotz a priori vielversprechender Copolymerisationseignung konnte jedoch keine Copolymerisation mit den zwitterionischen Vinylamidmonomeren erreicht werden. KW - antifouling KW - Antifouling KW - copolymers KW - Copolymere KW - hydrogels KW - Hydrogele KW - zwitterions KW - Zwitterionen KW - synthesis KW - Synthese Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-626820 ER - TY - THES A1 - Kwesiga, George T1 - Synthesis of isoflavonoids from African medicinal plants with activity against tropical infectious diseases T1 - Synthese von Isoflavonoiden aus afrikanischen Heilpflanzen mit Wirkung gegen tropische Infektionskrankheiten N2 - Two approaches for the synthesis of prenylated isoflavones were explored: the 2,3-oxidative rearrangement/cross metathesis approach, using hypervalent iodine reagents as oxidants and the Suzuki-Miyaura cross-coupling/cross metathesis approach. Three natural prenylated isoflavones: 5-deoxy-3′-prenylbiochanin A (59), erysubin F (61) and 7-methoxyebenosin (64), and non-natural analogues: 7,4′-dimethoxy-8,3′-diprenylisoflavone (126j) and 4′-hydroxy-7-methoxy-8,3′-diprenylisoflavone (128) were synthesized for the first time via the 2,3-oxidative rearrangement/cross metathesis approach, using mono- or diallylated flavanones as key intermediates. The reaction of flavanones with hypervalent iodine reagents afforded isoflavones via a 2,3-oxidative rearrangement and the corresponding flavone isomers via a 2,3-dehydrogenation. This afforded the synthesis of 7,4′-dimethoxy-8-prenylflavone (127g), 7,4′-dimethoxy-8,3′-diprenylflavone (127j), 7,4′-dihydroxy-8,3′-diprenylflavone (129) and 4′-hydroxy-7-methoxy-8,3′-diprenylflavone (130), the non-natural regioisomers of 7-methoxyebenosin, 126j, erysubin F and 128 respectively. Three natural prenylated isoflavones: 3′-prenylbiochanin A (58), neobavaisoflavone (66) and 7-methoxyneobavaisoflavone (137) were synthesized for the first time using the Suzuki-Miyaura cross-coupling/cross metathesis approach. The structures of 3′-prenylbiochanin A (58) and 5-deoxy-3′-prenylbiochanin A (59) were confirmed by single crystal X-ray diffraction analysis. The 2,3-oxidative rearrangement approach appears to be limited to the substitution pattern on both rings A and B of the flavanone while the Suzuki-Miyaura cross-coupling approach appears to be the most suitable for the synthesis of simple isoflavones or prenylated isoflavones whose prenyl substituents or allyl groups, the substituents that are essential precursors for the prenyl side chains, can be regioselectively introduced after the construction of the isoflavone core. The chalcone-flavanone hybrids 146, 147 and 148, hybrids of the naturally occurring bioactive flavanones liquiritigenin-7-methyl ether, liquiritigenin and liquiritigenin-4′-methyl ether respectively were also synthesized for the first time, using Matsuda-Heck arylation and allylic/benzylic oxidation as key steps. The intermolecular interactions of 5-deoxy-3′-prenylbiochanin A (59) and its two closely related precursors 106a and 106b was investigated by single crystal and Hirshfeld surface analyses to comprehend their different physicochemical properties. The results indicate that the presence of strong intermolecular O-H···O hydrogen bonds and an increase in the number of π-stacking interactions increases the melting point and lowers the solubility of isoflavone derivatives. However, the strong intermolecular O-H···O hydrogen bonds have a greater effect than the π-stacking interactions. 5-Deoxy-3′-prenylbiochanin A (59), erysubin F (61) and 7,4′-dihydroxy-8,3′-diprenylflavone (129), were tested against three bacterial strains and one fungal pathogen. All the three compounds were inactive against Salmonella enterica subsp. enterica (NCTC 13349), Escherichia coli (ATCC 25922), and Candida albicans (ATCC 90028), with MIC values greater than 80.0 μM. The diprenylated isoflavone erysubin F (61) and its flavone isomer 129 showed in vitro activity against methicillin-resistant Staphylococcus aureus (MRSA, ATCC 43300) at MIC values of 15.4 and 20.5 μM, respectively. 5-Deoxy-3′-prenylbiochanin A (59) was inactive against this MRSA strain. Erysubin F (61) and its flavone isomer 129 could serve as lead compounds for the development of new alternative drugs for the treatment of MRSA infections. N2 - Ziel dieser Studie war es, aus afrikanischen Heilpflanzen isolierte Naturstoffe künstlich herzustellen, die zur Behandlung tropischer Infektionskrankheiten wie Malaria und bakterieller Infektionen eingesetzt werden, um Schlüsselsubstanzen für die Entwicklung neuer Medikamente zu identifizieren. Sechs Naturstoffe aus afrikanischen Heilpflanzen wie dem Korallenbaum (Erythrina-species) wurden erstmals künstlich hergestellt. Bei der Herstellung dieser Naturstoffe wurden auch sechs weitere verwandte nicht-natürliche Analoga hergestellt. Zwei Naturstoffe (5-Deoxy-3′-prenylbiochanin A und Erysubin F) aus dem Korallenbaum (Erythrina sacleuxii) und eine verwandte nicht-natürliche Substanz wurden auf ihre antimikrobielle Aktivität gegen drei Bakterienstämme und einen Pilzstamm getestet. Alle drei Substanzen waren nicht wirksam gegen Escherichia coli, ein Bakterium, das Harnwegsinfektionen und Durchfall verursacht; Salmonella entrica, das Typhus verursacht, und Candida albicans, das Candidiasis verursacht. Erysubin F und sein nicht-natürliches Analogon waren sehr aktiv gegen Methicillin-resistente Staphylococcus aureus (MRSA), ein Bakterium, das hauptsächlich in sehr geringen Konzentrationen Hautinfektionen verursacht. 5-Deoxy-3'-prenylbiochanin A war gegen diesen MRSA-Stamm nicht aktiv. Erysubin F und sein nicht-natürliches Analogon könnten als Schlüsselsubstanzen für die Entwicklung eines neuen Medikaments gegen Infektionen durch MRSA dienen. KW - synthesis KW - isoflavonoids KW - African medicinal plants KW - tropical infectious diseases KW - Afrikanische Heilpflanzen KW - Isoflavonoide KW - Synthese KW - tropische Infektionskrankheiten Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-559069 ER - TY - THES A1 - Lood, Kajsa T1 - Stereoselective Construction of C-C Double Bonds via Olefin Metathesis: From Tethered Reactions to Water-Soluble Catalysts for Stereoretentive Metathesis T1 - Stereoselektiver Aufbau von C-C-Doppelbindungen durch Olefinmetathese: Von gebundenen Reaktionen zu wasserlöslichen Katalysatoren für die stereoretentive Metathese N2 - Natural products have proved to be a major resource in the discovery and development of many pharmaceuticals that are in use today. There is a wide variety of biologically active natural products that contain conjugated polyenes or benzofuran structures. Therefore, new synthetic methods for the construction of such building blocks are of great interest to synthetic chemists. The recently developed one-pot tethered ring-closing metathesis approach allows for the formation of Z,E-dienoates in high stereoselectivity. The extension of this method with a Julia-Kocienski olefination protocol would allow for the formation of conjugated trienes in a stereoselective manner. This strategy was applied in the total synthesis of conjugated triene containing (+)-bretonin B. Additionally, investigations of cross metathesis using methyl substituted olefins were pursued. This methodology was applied, as a one-pot cross metathesis/ring-closing metathesis sequence, in the total synthesis of benzofuran containing 7-methoxywutaifuranal. Finally, the design and synthesis of a catalyst for stereoretentive metathesis in aqueous media was investigated. N2 - Naturstoffe haben sich als wichtige Ressource für die Entdeckung und Entwicklung zahlreicher Arzneimittel erwiesen, die heute verwendet werden. Es gibt eine Vielzahl biologisch aktiver Naturstoffe, die konjugierte Polyene oder Benzofuranstrukturen enthalten. Daher sind neue Synthesemethoden für die Herstellung solcher Bausteine für synthetische Chemiker von großem Interesse. Der kürzlich entwickelte Ein-Topf-Ansatz der tethered ring-closing metathesis ermöglicht die Bildung von Z,E-Dienoaten in hoher Stereoselektivität. Die Erweiterung dieser Methode mit einem Julia-Kocienski-Olefinierungsprotokoll würde die Bildung von konjugierten Trienen in stereoselektiver Weise ermöglichen. Diese Strategie wurde bei der Totalsynthese von konjugierten Trienen, die (+)-Bretonin B enthalten, angewandt. Außerdem wurden Untersuchungen zur Kreuzmetathese mit methylsubstituierten Olefinen durchgeführt. Diese Methodik wurde als Ein-Topf-Kreuzmetathese/Ringschluss-Metathese-Sequenz in der Totalsynthese von benzofuranhaltigem 7-Methoxywutaifuranal angewendet. Schließlich wurde die Entwicklung und Synthese eines Katalysators für die stereoretentive Metathese in wässrigen Medien untersucht. KW - Olefin metathesis KW - synthesis KW - organic chemistry KW - catalysts KW - Olefin Metathese KW - Synthese KW - organische Chemie KW - Katalysatoren Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-539142 ER - TY - THES A1 - Steeples, Elliot T1 - Amino acid-derived imidazolium salts: platform molecules for N-Heterocyclic carbene metal complexes and organosilica materials T1 - Imidazolium-Salze aus Aminosäure: Bausteine für N-Heterozyklische-Carben Metallkomplexe und Organosilicamaterialien N2 - In the interest of producing functional catalysts from sustainable building-blocks, 1, 3-dicarboxylate imidazolium salts derived from amino acids were successfully modified to be suitable as N-Heterocyclic carbene (NHC) ligands within metal complexes. Complexes of Ag(I), Pd(II), and Ir(I) were successfully produced using known procedures using ligands derived from glycine, alanine, β-alanine and phenylalanine. The complexes were characterized in solid state using X-Ray crystallography, which allowed for the steric and electronic comparison of these ligands to well-known NHC ligands within analogous metal complexes. The palladium complexes were tested as catalysts for aqueous-phase Suzuki-Miyaura cross-coupling. Water-solubility could be induced via ester hydrolysis of the N-bound groups in the presence of base. The mono-NHC–Pd complexes were seen to be highly active in the coupling of aryl bromides with phenylboronic acid; the active catalyst of which was determined to be mostly Pd(0) nanoparticles. Kinetic studies determined that reaction proceeds quickly in the coupling of bromoacetophenone, for both pre-hydrolyzed and in-situ hydrolysis catalyst dissolution. The catalyst could also be recycled for an extra run by simply re-using the aqueous layer. The imidazolium salts were also used to produce organosilica hybrid materials. This was attempted via two methods: by post-grafting onto a commercial organosilica, and co-condensation of the corresponding organosilane. The co-condensation technique harbours potential for the production of solid-support catalysts. N2 - Um Katalysatoren aus nachhaltigen Chemikalien herzustellen, wurden 1,3-Dicarbonsäure-Imidazolium-Salze, welche aus Aminosäuren synthetisiert wurden als N-heterozyklische-Carben-Liganden (NHC) in Metallkomplexen modifiziert. Liganden aus Glycin, Alanin, β-Alanin und Phenylalanin wurden wiederum genutzt, um Metallkomplexe aus Silber(I), Palladium(II) und Iridium(I) darzustellen. Alle Komplexverbindungen wurden mit Röntgenkristallographie charakterisiert. Die Palladiumkomplexe wurden als Katalysatoren in der Suzuki-Miyaura Reaktion eingesetzt. Durch zusätzliche Hydrolyse der Ester-Gruppen konnte eine gute Wasserlöslichkeit erreicht werden. Die hohe Aktivität der Mono-NHC–Palladium-Komplexe konnte bei der Kupplung von Arylbromiden mit Phenylboronsäuren aufgezeigt werden. Die aktive Spezies wurde hauptsächlich Pd(0) Nanopartikeln zugeschrieben. Nach erfolgreichem Recycling konnte der Katalysator noch einmal wiederverwendet werden. Die Imidazolium-Salze wurden ebenfalls herangezogen, um Organosilicamaterialien zu synthetisieren. Die Herstellung wurde durch zwei Methoden erreicht. Zum einen durch nachträgliches Aufbringen auf kommerzielle Siliziummaterialien, sowie durch Co-Kondensation auf das entsprechende Organosilan. Diese Co-Kondensation birgt Potential zur Herstellung von festen Trägerkatalysatoren. KW - synthesis KW - Synthese KW - sustainable chemistry KW - nachhaltige Chemie KW - organometallics KW - Metallorganischen KW - water KW - Wasser Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-101861 ER - TY - THES A1 - Herfurth, Christoph T1 - Einstufen-Synthese und Charakterisierung amphiphiler Sternpolymere als multifunktionale assoziative Verdicker T1 - One-step synthesis and characterisation of amphiphilic star polymers as multifunctional associative thickeners N2 - Typische assoziative Verdicker für wässrige Systeme basieren auf linearen, doppelt hydrophob endmodifizierten Poly(ethylenglykolen) (PEGs). Diese Polymere aggregieren aufgrund ihrer Struktur in wässriger Lösung und bilden ein Netzwerk aus verbrückten Polymer-Mizellen. Dabei kann ein Polymer-Molekül maximal zwei Mizellen miteinander verbinden. Bisher ist unklar, wie die Anzahl der Endgruppen eines verzweigten, mehrfach hydrophob endmodifizierten hydrophilen Polymers die Struktur und Dynamik solcher Netzwerke beeinflusst. Die Synthese verzweigter Polymere auf PEG-Basis erfolgt mittels lebender ionischer Polymerisation und ist experimentell aufwändig. Das Einführen hydrophober Endgruppen erfordert zusätzliche Synthese-Schritte. In dieser Arbeit wurden hydrophile Sternpolymere mit hydrophoben Endgruppen in einem Schritt hergestellt. Dazu wurde die Technik der radikalischen Polymerisation unter Kettenübertragung durch reversible Addition und anschließende Fragmentierung (reversible addition-fragmentation chain transfer, RAFT) genutzt. Die Synthese der Sternpolymere erfolgte von einem multifunktionalen Kern, der die R-Gruppe der RAFT-Kettenüberträger (chain transfer agents, CTAs) bildete. Die dazu benötigten CTAs wurden so konzipiert, dass mit ihrer Hilfe sowohl die Anzahl der Arme des Sternpolymers (von 2 bis 4), als auch die Länge der hydrophoben Endgruppe (C4, C12, C18) variiert werden konnte. Der große Vorteil der RAFT-Polymerisation ist, dass sie viele polare Monomere für die Synthese der hydrophilen Arme des Sternpolymers toleriert. In dieser Arbeit wurden als Modell-Monomere Oligo(ethylenglykol)methylether-acrylat (OEGA) und N,N-Dimethylacrylamid (DMA) eingesetzt. Beide Monomere bilden nicht-ionische hydrophile Polymere. Poly(OEGA) ist ein Kammpolymer, das auf PEG basiert. Poly(DMA) besitzt dagegen eine deutlich kompaktere Struktur. Die erhaltenen amphiphilen Sternpolymere wurden umfassend molekular charakterisiert. Die Molmassen wurden mit verschiedenen GPC-Systemen bestimmt und der Grad der Endgruppenfunktionalisierung wurde mittels UV/Vis- und 1H-NMR-Spektroskopie überprüft. Die Polymerisation von OEGA zeigt mit den CTAs einige Charakteristika der Polymerisation mit reversibler Deaktivierung (RDRP, auch „kontrollierte radikalische Polymerisation“), wird aber durch Kettenübertragung zum Monomer bzw. Polymer gestört. Diese Nebenreaktion ist auf die Struktur des Monomers als Oligoether zurückzuführen. Bei allen untersuchten Polymerisationen von DMA mit den multifunktionalen CTAs steigt die Molmasse linear mit dem Umsatz. Die erhaltenen Polymere zeigen durchweg monomodale und enge Molmassenverteilungen (PDI ≤ 1,2). Die Molmassen lassen sich in einem weiten Bereich von 25 kg/mol bis 150 kg/mol einstellen und die Endgruppen der Polymere bleiben zu 90 % erhalten. Während die Polymerisation von DMA sowohl mit den di- als auch den trifunktionalen CTAs innerhalb von 3 h zu quantitativen Umsätzen verläuft, wird der quantitative Umsatz des Monomers bei der Polymerisation mit tetrafunktionalen CTAs erst nach 4 h erreicht. Diese Verzögerung ist auf eine Retardierung in der Anfangsphase der Polymerisation zurückzuführen, die sich aus der besonderen Struktur der tetrafunktionalen CTAs erklärt. Auf dem System zur Polymerisation von DMA aufbauend ließen sich Gradienten-Block-Copolymere in Eintopfreaktionen herstellen. Dazu wurde nach Erreichen des quantitativen Umsatzes von DMA ein zweites Monomer zur Reaktionsmischung gegeben. Mit Ethylacrylat (EtA) wurden so lineare amphiphile symmetrische Triblock-Copolymere erhalten. Dabei wurde die Länge des hydrophoben Blocks durch unterschiedliche Mengen an EtA variiert. Mit N,N-Diethylacrylamid (DEA) wurden lineare symmetrische Triblock-Copolymere sowie 3-Arm Stern-Diblock-Copolymere hergestellt, die über einen thermisch schaltbaren zweiten Block verfügen. Bei diesen Polymeren lässt sich die Länge des hydrophoben Teils in situ durch Veränderung der Temperatur variieren. Das Verhalten der amphiphilen Sternpolymere in wässriger Lösung und in Mikroemulsion wurde im Rahmen einer Kooperation an der TU Berlin mit Hilfe von Kleinwinkel-Neutronenstreuung (SANS), dynamischer Lichtstreuung (DLS) und Rheologie untersucht. Die Polymere wirken durch Assoziation der hydrophoben Endgruppen als effektive Verdicker sowohl allein in wässriger Lösung als auch in Mikroemulsion. Die Struktur des gebildeten Netzwerks hängt dabei von der Konzentration des Polymers in der Lösung und der Länge der Endgruppe (Hydrophobie) ab. Die dynamischen Eigenschaften der Lösungen werden außerdem durch die Anzahl der Arme der Polymere bestimmt. N2 - Typically, associative thickeners for aqueous system consist of linear, hydrophobically α,ω-end-capped poly(ethylene glycols) (PEGs). Owing to their structure, these polymers aggregate in aqueous solution, forming a network of bridged micelles. Thus, one polymer molecule can link not more than two micelles. Until now it is unclear whether the structure and dynamics of such networks are influenced by the number of end groups of a branched multiply hydrophobically end-capped hydrophilic polymers. Branched PEG-based polymers are synthesized using the laborious and limited techniques of living ionic polymerization. Introducing hydrophobic end groups demands a multiple-step process. This work presents the one-step synthesis of hydrophilic star polymers with hydrophobic end groups, using reversible addition fragmentation chain transfer (RAFT) polymerization. This radical polymerization method is easy to use and tolerates a large number of polar monomers for the synthesis of the hydrophilic arms of the star polymers. The arms of the polymer were grown from a multifunctional core that formed the R-group of the chain transfer agents (CTAs). The CTAs where tailored to be able to vary the number of arms of the star polymers from 2 to 4 and to vary the length (and therefore the hydrophobicity) of the end groups (C4, C12, C18). Two different polar monomers where used as model monomers: Oligo(ethylene glycol)methyl ether acrylate (OEGA) and N,N-Dimethylacrylamide (DMA). Both monomers yield non-ionic hydrophilic polymers. While poly(OEGA) is a comb polymer based on PEG, poly(DMA) exhibits a more compact structure. The amphiphilic star polymers were characterized extensively. The molar masses were determined using GPC in various solvents and the degree of end functionalisation was monitored using 1H NMR and UV/Vis spectroscopy. The polymerization of OEGA shows some of the expected characteristics of reversible deactivation radical polymerization (RDRP). However, chain transfer to monomer and polymer is a prominent side reaction, limiting the use of this monomer for the fabrication of well-defined material. This reaction can be attributed to the structure of the monomer being an oligoether. For all examined polymerizations of DMA with the multifunctional CTAs the molar mass increased linearly with conversion. The molar mass distributions were monomodal and narrow (PDI ≤ 1.2). Expected values were reached for molar masses from 25 to 150 kg/mol and the end group functionality was about 90 % in all cases. While the polymerization of DMA using di- and trifunctional CTAs proceeded to quantitative conversion within 3 h, an initial retardation period of about 60 min was observed for the polymerization using tetrafunctional CTAs. This retardation was attributed to the peculiar molecular structure of these CTAs. Owing to the well-controlled features of the polymerization of DMA using the multifunctional CTAs, this system was used to obtain tapered block copolymers in a one-pot process. These structures were achieved by adding a second monomer to the reaction mixture after the quantitative conversion of DMA. Using ethyl acrylate (EtA), linear amphiphilic symmetrical triblock copolymers were synthesized. The length of the hydrophobic block was tailored by the addition of varying amounts of EtA. With N,N-Diethylacrylamide as a second monomer, linear symmetric triblock copolymers as well as 3-arm star diblock copolymers were obtained that contain a thermosensitve block. Altering the temperature of aqueous solutions of these polymers varies the length of the hydrophobic block in situ. At the TU Berlin, the behavior of the polymers was studied in aqueous solution as well as in microemulsion. The solutions were characterized by small angle neutron scattering (SANS), dynamic light scattering (DLS) and rheology. The end groups of the polymers aggregate, making the polymers efficient thickeners both in aqueous solution and in microemulsion. The structure of the formed network depends on the concentration of the polymer in solution and on the length of the end group. The dynamic properties of the solutions are governed additionally by the number of arms. KW - RAFT-Polymerisation KW - Sternpolymere KW - Synthese KW - Amphiphile Polymere KW - Assoziative Verdicker KW - RAFT polymerisation KW - star polymers KW - synthesis KW - amphiphilic polymers KW - associative thickeners Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-62446 ER - TY - THES A1 - Bivigou Koumba, Achille Mayelle T1 - Design, Synthesis and Characterisation of Amphiphilic Symmetrical triblock copolymers by the RAFT process : their self-organisation in dilute and concentrated aqueous solutions T1 - Design, Synthese und Charakterisierung von amphiphilen symmetrischen Triblock-Copolymeren anhand des RAFT Prozesses : ihre Selbstorganisation in wässrigen verdünnten und höher konzentrierten Lösungen N2 - This work presents the synthesis and the self-assembly of symmetrical amphiphilic ABA and BAB triblock copolymers in dilute, semi-concentrated and highly concentrated aqueous solution. A series of new bifunctional bistrithiocarbonates as RAFT agents was used to synthesise these triblock copolymers, which are characterised by a long hydrophilic middle block and relatively small, but strongly hydrophobic end blocks. As hydrophilic A blocks, poly(N-isopropylacrylamide) (PNIPAM) and poly(methoxy diethylene glycol acrylate) (PMDEGA) were employed, while as hydrophobic B blocks, poly(4-tert-butyl styrene), polystyrene, poly(3,5-dibromo benzyl acrylate), poly(2-ethylhexyl acrylate), and poly(octadecyl acrylate) were explored as building blocks with different hydrophobicities and glass transition temperatures. The five bifunctional trithiocarbonates synthesised belong to two classes: the first are RAFT agents, which position the active group of the growing polymer chain at the outer ends of the polymer (Z-C(=S)-S-R-S-C(=S)-Z, type I). The second class places the active groups in the middle of the growing polymer chain (R-S-C(=S)-Z-C(=S)-S-R, type II). These RAFT agents enable the straightforward synthesis of amphiphilic triblock copolymers in only two steps, allowing to vary the nature of the hydrophobic blocks as well as the length of the hydrophobic and hydrophilic blocks broadly with good molar mass control and narrow polydispersities. Specific side reactions were observed among some RAFT agents including the elimination of ethylenetrithiocarbonate in the early stage of the polymerisation of styrene mediated by certain agents of the type II, while the use of the RAFT agents of type I resulted in retardation of the chain extension of PNIPAM with styrene. These results underline the need of a careful choice of RAFT agents for a given task. The various copolymers self-assemble in dilute and semi-concentrated aqueous solution into small flower-like micelles. No indication for the formation of micellar clusters was found, while only at high concentration, physical hydrogels are formed. The reversible thermoresponsive behaviour of the ABA and BAB type copolymer solutions in water with A made of PNIPAM was examined by turbidimetry and dynamic light scattering (DLS). The cloud point of the copolymers was nearly identical to the cloud point of the homopolymer and varied between 28-32 °C with concentrations from 0.01 to 50 wt%. This is attributed to the formation of micelles where the hydrophobic blocks are shielded from a direct contact with water, so that the hydrophobic interactions of the copolymers are nearly the same as for pure PNIPAM. Dynamic light scattering measurements showed the presence of small micelles at ambient temperature. The aggregate size dramatically increased above the cloud point, indicating a change of aggregate morphology into clusters due to the thermosensitivity of the PNIPAM block. The rheological behaviour of the amphiphilic BAB triblock copolymers demonstrated the formation of hydrogels at high concentrations, typically above 30-35 wt%. The minimum concentration to induce hydrogels decreased with the increasing glass transition temperatures and increasing length of the end blocks. The weak tendency to form hydrogels was attributed to a small share of bridged micelles only, due to the strong segregation regime occurring. In order to learn about the role of the nature of the thermoresponsive block for the aggregation, a new BAB triblock copolymer consisting of short polystyrene end blocks and PMDEGA as stimuli-responsive middle block was prepared and investigated. Contrary to PNIPAM, dilute aqueous solutions of PMDEGA and of its block copolymers showed reversible phase transition temperatures characterised by a strong dependence on the polymer composition. Moreover, the PMDEGA block copolymer allowed the formation of physical hydrogels at lower concentration, i.e. from 20 wt%. This result suggests that PMDEGA has a higher degree of water-swellability than PNIPAM. N2 - Die Arbeit behandelt die Synthese und das Selbstorganisationsverhalten von neuen funktionellen symmetrischen "stimuli-responsiven" Triblockcopolymeren ABA und BAB in wässrigen verdünnten und höher konzentrierten Lösungen. Neue symmetrische, bifunktionelle Bistrithiocarbonate wurden als RAFT-Agentien benutzt, um Triblockcopolymere mit langen hydrophilen (A) Innen- und kurzen hydrophoben (B) Außenblöcken zu synthetisieren. Als hydrophile A Blöcke wurden Poly(N-isopropylacrylamid) PNIPAM und Poly(methoxy diethylene glykol acrylat) PMDEGA benutzt, während als hydrophobe Blöcke B Poly(4-tert-butyl styrol), Polystyrol, Poly(3,5-dibromo benzyl acrylat), Poly(2-ethylhexyl acrylat), und Poly(octadecyl acrylat) als Bausteine mit unterschiedlicher Glasübergangstemperatur untersucht wurden. Die Selbstorganisation von ABA und BAB Copolymeren in Wasser mit A Blöcken aus PNIPAM wurde anhand von Trübungsphotometrie, dynamischer Lichtstreuung (DLS) und Rheologie untersucht. Die amphiphilen Blockcopolymere sind direkt wasserlöslich. Bei Konzentrationen von 0.01 bis 50 wt% zeigen Trübungsmessungen bei den Blockcopolymeren wie bei den Homopolymeren eine Übergangstemperatur bei 28-32 °C. Zurückzuführen ist dies auf die Bildung von Mizellen, bei der die hydrophoben Blöcke von einem direkten Kontakt mit Wasser abgeschirmt werden. DLS zeigt kleine Mizellen bei niedrigen Temperaturen und Aggregate mit großem hydrodynamischem Durchmesser bei Temperaturen oberhalb der Übergangstemperatur. Die rheologische Untersuchung von BAB Polymeren zeigt die Bildung von Hydrogelen bei höheren Konzentrationen (über 30-35 wt%). Die minimal benötigte Konzentration, bei der die von Hydrogelen auftreten, nimmt mit wachsender Glasübergangstemperatur ab, und nimmt mit der Länge der hydrophoben Blöcke B zu. Im Unterschied zu PNIPAM zeigen wässrige Lösungen von PMDEGA und seinen Blockcopolymeren reversible Übergangstemperaturen abhängig von der chemischen Struktur. Außerdem bilden PMDEGA Blockcopolymere Hydrogele bei niedriger Konzentration (ab 20 wt%). Dieses Ergebnis deutet darauf hin, dass PMDEGA stärker Wasser bindet als PNIPAM. KW - Design KW - Synthese KW - Charakterisierung KW - Triblock-Copolymere KW - RAFT KW - Design KW - Synthesis KW - Characterisation KW - Triblock Copolymers KW - RAFT Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-39549 ER - TY - THES A1 - Imran ul-haq, Muhammad T1 - Synthesis of fluorinated polymers in supercritical carbon dioxide (scCO₂) T1 - Synthese von Fluorpolymeren in überkritischem Kohlendioxid (scCO₂) N2 - For the first time stabilizer-free vinylidene fluoride (VDF) polymerizations were carried out in homogeneous phase with supercritical CO₂. Polymerizations were carried out at 140°C, 1500 bar and were initiated with di-tert-butyl peroxide (DTBP). In-line FT-NIR (Fourier Transform- Near Infrared) spectroscopy showed that complete monomer conversion may be obtained. Molecular weights were determined via size-exclusion chromatography (SEC) and polymer end group analysis by 1H-NMR spectroscopy. The number average molecular weights were below 104 g∙mol−1 and polydispersities ranged from 3.1 to 5.7 depending on DTBP and VDF concentration. To allow for isothermal reactions high CO₂ contents ranging from 61 to 83 wt.% were used. The high-temperature, high-pressure conditions were required for homogeneous phase polymerization. These conditions did not alter the amount of defects in VDF chaining. Scanning electron microscopy (SEM) indicated that regular stack-type particles were obtained upon expansion of the homogeneous polymerization mixture. To reduce the required amount of initiator, further VDF polymerizations using chain transfer agents (CTAs) to control molecular weights were carried out in homogeneous phase with supercritical carbon dioxide (scCO₂) at 120 °C and 1500 bar. Using perfluorinated hexyl iodide as CTA, polymers of low polydispersity ranging from 1.5 to 1.2 at the highest iodide concentration of 0.25 mol·L-1 were obtained. Electrospray ionization- mass spectroscopy (ESI-MS) indicates the absence of initiator derived end groups, supporting livingness of the system. The “livingness” is based on the labile C-I bond. However, due to the weakness of the C-I bond perfluorinated hexyl iodide also contributes to initiation. To allow for kinetic analyses of VDF polymerizations the CTA should not contribute to initiation. Therefore, additional CTAs were applied: BrCCl3, C6F13Br and C6F13H. It was found that C6F13H does not contribute to initiation. At 120°C and 1500 bar kp/kt0.5~ 0.64 (L·mol−1·s−1)0.5 was derived. The chain transfer constant (CT) at 120°C has been determined to be 8·10−1, 9·10−2 and 2·10−4 for C6F13I, C6F13Br and C6F13H, respectively. These CT values are associated with the bond energy of the C-X bond. Moreover, the labile C-I bond allows for functionalization of the polymer to triazole end groups applying click reactions. After substitution of the iodide end group by an azide group 1,3 dipolar cycloadditions with alkynes yield polymers with 1,2,3 triazole end groups. Using symmetrical alkynes the reactions may be carried out in the absence of any catalyst. This end-functionalized poly (vinylidene fluoride) (PVDF) has higher thermal stability as compared to the normal PVDF. PVDF samples from homogeneous phase polymerizations in supercritical CO₂ and subsequent expansion to ambient conditions were analyzed with respect to polymer end groups, crystallinity, type of polymorphs and morphology. Upon expansion the polymer was obtained as white powder. Scanning electron microscopy (SEM) showed that DTBP derived polymer end groups led to stack-type particles whereas sponge- or rose-type particles were obtained in case of CTA fragments as end groups. Fourier-Transform Infrared spectroscopy and wide angle X-ray diffraction indicated that the type of polymorph, α or β crystal phase was significantly affected by the type of end group. The content of β-phase material, which is responsible for piezoelectricity of PVDF, is the highest for polymer with DTBP-derived end groups. In addition, the crystallinity of the material, as determined via differential scanning calorimetry is affected by the end groups and polymer molecular weights. For example, crystallinity ranges from around 26 % for DTBP-derived end groups to a maximum of 62 % for end groups originating from perfluorinated hexyl iodide for polymers with Mn ~2200 g·mol–1. Expansion of the homogeneous polymerization mixture results in particle formation by a non-optimized RESS (Rapid Expansion from Supercritical Solution) process. Thus, it was tested how polymer end groups affect the particles size distribution obtained from RESS process under controlled conditions (T = 50°C and P = 200 bar). In all RESS experiments, small primary PVDF with diameters less than 100 nm without the use of liquid solvents, surfactants, or other additives were produced. A strong correlation between particle size and particle size distribution with polymer end groups and molecular weight of the original material was observed. The smallest particles were found for RESS of PVDF with Mn~ 4000 g·mol–1 and PFHI (C6F13I) - derived end groups. N2 - Erstmalig gelang es, stabilisatorfreie Vinylidenfluorid (VDF)-Polymerisationen in homogener Phase mit überkritischem CO₂ (scCO₂) bis zu vollständigem Monomerumsatz durchzuführen. Die Homogenität während der Polymerisation wurde durch in-line Fourier-Transform Nahinfrarot Spektroskopie beobachtet. Für Polymerisationen bei 140 °C und 1500 bar wurde Di-tert-butylperoxid (DTBP) als Initiator verwendet. Es wurden Polymere mit einem Zahlenmittel der Molmasse kleiner 104 g·mol–1 und Polydispersitäten zwischen 3.1 und 5.7. erhalten. Um isotherme Reaktionen zu ermöglichen, wurden CO₂-Gehalte zwischen 61 und 83 wt.% verwendet. Die für die homogene Reaktionsführung erforderlichen hohen Drücke und Temperaturen haben keinen Einfluss auf die Mikrostruktur des Polymers. Zur Verringerung der Initiatorkonzentration wurden weitere Polymerisationen unter Verwendung von Kettentransferreagenzien (CTA) bei 120 °C und 1500 bar in homogener Phase mit scCO₂ durchgeführt. Perfluoriertes Hexyliodid als CTA ermöglicht kontrollierte radikalische Polymerisationen, wobei Polymere mit geringer Polydispersität zwischen 1.5 und 1.2 erhalten wurden. Endgruppenanalyse mit Elektronenspray-Ionisations-Massen¬spektro¬metrie (ESI-MS) zeigte, dass keine Initiatorendgruppen im Polymer enthalten sind. Diese Beobachtung unterstützt den lebenden Charakter der Polymerisationen und basiert auf einer labilen C-I-Bindung im Polymer. Aufgrund der schwachen C-I-Bindung trägt das perfluorierte Hexyliodid (C6F13I) auch zur Initiierung bei. Polymerisationen in Gegenwart von BrCCl3, C6F13Br und C6F13H zeigten, dass nur C6F13H keinen Beitrag zur Initiierung leistet. Bei 120 °C und 1500 bar wurde ein kp/kt0.5 von ~ 0.64 (L·mol−1·s−1)0.5 bestimmt, wobei kp der Wachstums- und kt der Terminierungsgeschwindigkeitskoeffizient sind. Die Kettentransfer¬konstanten (CT) bei 120°C betragen 8·10−1, 9·10−2 und 2·10−4 für C6F13I, C6F13Br und C6F13H. Die Änderung der CT-Werte lässt sich mit der zunehmenden Bindungsenergie in der Reihe C-I, C-Br und C-H erklären. Die labile C-I-Bindung ermöglicht eine Funktionalisierung des Polymers durch Click-Reaktionen. Nach Substitution der Iodid-Endgruppe durch eine Azidgruppe erfolgte eine katalysatorfreie 1,3-dipolare Cyclaoaddition mit Alkinen zu Polymeren mit 1,2,3-Triazol-Endgruppen. Dieses endfunktionalisierte PVDF besitzt im Vergleich zu konventionellem PVDF eine höhere thermische Stabilität. Nach der Expansion der Polymerisationsmischung mit scCO₂ auf Umgebungsbedingungen lag das Polymer als weißes Pulver vor, das im Hinblick auf z.B. Polymerendgruppen, Kristallinität, Gestalt und Größe der Partikel untersucht wurde. Rasterelektronenmikroskopie zeigte, dass Polymere mit DTBP-Endgruppen zu stapelförmigen Partikeln führen, während bei CTA-Fragmenten als Endgruppen schwamm- oder rosenartige Partikel erhalten wurden. Ergebnisse der FT-IR Spektroskopie und Weitwinkelröntgenbeugung zeigten, dass der höchste Gehalt an β-phasigem Material, der für die Piezoelektrizität des PVDF verantwortlich ist, für PVDF mit Initiatorendgruppen erhalten wurde. DSC (Differential Scanning Calorimetry) Messungen ergaben zudem, dass der Kristallinitätsgrad durch Endgruppen und Polymermasse beeinflusst wird. Die Expansion der homogenen Polymermischung kann als nicht-optimierter RESS-Prozess (Rapid Expanison from Supercritical Solution,) angesehen werden. Aus RESS Experimenten unter kontrollierten Bedingungen wurden jeweils nanoskalige primäre PVDF-Partikel ohne Verwendung von Lösungsmitteln, Tensiden oder anderen Additiven erhalten. Es besteht ein enger Zusammenhang zwischen einerseits der Partikelgröße und der Partikelgrößenverteilung und andererseits der Polymerkonzentration in scCO₂ vor der Expansion, bestimmt durch Polymerendgruppen und Molmassen der eingesetzten Materialien. KW - Synthese KW - Fluorpolymere KW - überkritisches Kohlendioxid (scCO₂) KW - Synthesis KW - fluorinated polymers KW - supercritical carbon dioxide (scCO₂) Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-19868 ER -