TY - THES A1 - Pilz, Marco T1 - A comparison of proxies for seismic site conditions and amplification for the large urban area of Santiago de Chile T1 - Ein Vergleich seismischer Parameter für die Standort- und Verstärkungsabschätzung im Stadtgebiet von Santiago de Chile N2 - Situated in an active tectonic region, Santiago de Chile, the country´s capital with more than six million inhabitants, faces tremendous earthquake hazard. Macroseismic data for the 1985 Valparaiso and the 2010 Maule events show large variations in the distribution of damage to buildings within short distances indicating strong influence of local sediments and the shape of the sediment-bedrock interface on ground motion. Therefore, a temporary seismic network was installed in the urban area for recording earthquake activity, and a study was carried out aiming to estimate site amplification derived from earthquake data and ambient noise. The analysis of earthquake data shows significant dependence on the local geological structure with regards to amplitude and duration. Moreover, the analysis of noise spectral ratios shows that they can provide a lower bound in amplitude for site amplification and, since no variability in terms of time and amplitude is observed, that it is possible to map the fundamental resonance frequency of the soil for a 26 km x 12 km area in the northern part of the Santiago de Chile basin. By inverting the noise spectral rations, local shear wave velocity profiles could be derived under the constraint of the thickness of the sedimentary cover which had previously been determined by gravimetric measurements. The resulting 3D model was derived by interpolation between the single shear wave velocity profiles and shows locally good agreement with the few existing velocity profile data, but allows the entire area, as well as deeper parts of the basin, to be represented in greater detail. The wealth of available data allowed further to check if any correlation between the shear wave velocity in the uppermost 30 m (vs30) and the slope of topography, a new technique recently proposed by Wald and Allen (2007), exists on a local scale. While one lithology might provide a greater scatter in the velocity values for the investigated area, almost no correlation between topographic gradient and calculated vs30 exists, whereas a better link is found between vs30 and the local geology. When comparing the vs30 distribution with the MSK intensities for the 1985 Valparaiso event it becomes clear that high intensities are found where the expected vs30 values are low and over a thick sedimentary cover. Although this evidence cannot be generalized for all possible earthquakes, it indicates the influence of site effects modifying the ground motion when earthquakes occur well outside of the Santiago basin. Using the attained knowledge on the basin characteristics, simulations of strong ground motion within the Santiago Metropolitan area were carried out by means of the spectral element technique. The simulation of a regional event, which has also been recorded by a dense network installed in the city of Santiago for recording aftershock activity following the 27 February 2010 Maule earthquake, shows that the model is capable to realistically calculate ground motion in terms of amplitude, duration, and frequency and, moreover, that the surface topography and the shape of the sediment bedrock interface strongly modify ground motion in the Santiago basin. An examination on the dependency of ground motion on the hypocenter location for a hypothetical event occurring along the active San Ramón fault, which is crossing the eastern outskirts of the city, shows that the unfavorable interaction between fault rupture, radiation mechanism, and complex geological conditions in the near-field may give rise to large values of peak ground velocity and therefore considerably increase the level of seismic risk for Santiago de Chile. N2 - Aufgrund ihrer Lage in einem tektonisch aktiven Gebiet ist Santiago de Chile, die Hauptstadt des Landes mit mehr als sechs Millionen Einwohnern, einer großen Erdbebengefährdung ausgesetzt. Darüberhinaus zeigen makroseismische Daten für das 1985 Valparaiso- und das 2010 Maule-Erdbeben eine räumlich unterschiedliche Verteilung der an den Gebäuden festgestellten Schäden; dies weist auf einen starken Einfluss der unterliegenden Sedimentschichten und der Gestalt der Grenzfläche zwischen den Sedimenten und dem Festgestein auf die Bodenbewegung hin. Zu diesem Zweck wurde in der Stadt ein seismisches Netzwerk für die Aufzeichnung der Bodenbewegung installiert, um die auftretende Untergrundverstärkung mittels Erdbebendaten und seismischem Rauschen abzuschätzen. Dabei zeigt sich für die Erdbebendaten eine deutliche Abhängigkeit von der Struktur des Untergrunds hinsichtlich der Amplitude der Erschütterung und ihrer Dauer. Die Untersuchung der aus seismischem Rauschen gewonnenen horizontal-zu-vertikal-(H/V) Spektral-verhältnisse zeigt, dass diese Ergebnisse nur einen unteren Grenzwert für die Bodenverstärkung liefern können. Weil jedoch andererseits keine zeitliche Veränderung bei der Gestalt dieser Spektralverhältnisse festgestellt werden konnte, erlauben die Ergebnisse ferner, die Resonanzfrequenz des Untergrundes für ein 26 km x 12 km großes Gebiet im Nordteil der Stadt zu bestimmen. Unter Zuhilfenahme von Informationen über die Dicke der Sedimentschichten, welche im vorhinein schon durch gravimetrische Messungen bestimmt worden war, konnten nach Inversion der H/V-Spektralverhältnisse lokale Scherwellengeschwindigkeitsprofile und nach Interpolation zwischen den einzelnen Profilen ein dreidimensionales Modell berechnet werden. Darüberhinaus wurde mit den verfügbaren Daten untersucht, ob auf lokaler Ebene ein Zusammenhang zwischen der mittleren Scherwellengeschwindigkeit in den obersten 30 m (vs30) und dem Gefälle existiert, ein Verfahren, welches kürzlich von Wald und Allen (2007) vorgestellt wurde. Da für jede lithologische Einheit eine starke Streuung für die seismischen Geschwindigkeiten gefunden wurde, konnte kein Zusammenhang zwischen dem Gefälle und vs30 hergestellt werden; demgegenüber besteht zumindest ein tendenzieller Zusammenhang zwischen vs30 und der unterliegenden Geologie. Ein Vergleich der Verteilung von vs30 mit den MKS-Intensitäten für das 1985 Valparaiso-Erdbeben in Santiago zeigt, dass hohe Intensitätswerte vor allem in Bereichen geringer vs30-Werte und dicker Sedimentschichten auftraten. Weiterhin ermöglichte die Kenntnis über das Sedimentbeckens Simulationen der Bodenbewegung mittels eines spektralen-Elemente-Verfahrens. Die Simulation eines regionalen Erdbebens, welches auch von einem dichten seismischen Netzwerk aufgezeichnet wurde, das im Stadtgebiet von Santiago infolge des Maule-Erdbebens am 27. Februar 2010 installiert wurde, zeigt, dass das Modell des Sedimentbeckens realistische Berechnungen hinsichtlich Amplitude, Dauer und Frequenz erlaubt und die ausgeprägte Topographie in Verbindung mit der Form der Grenzfläche zwischen den Sedimenten und dem Festgestein starken Einfluss auf die Bodenbewegung haben. Weitere Untersuchungen zur Abhängigkeit der Bodenerschütterung von der Position des Hypozentrums für ein hypothetisches Erdbeben an der San Ramón-Verwerfung, welche die östlichen Vororte der Stadt kreuzt, zeigen, dass die ungünstige Wechselwirkung zwischen dem Verlauf des Bruchs, der Abstrahlung der Energie und der komplexen geologischen Gegebenheiten hohe Werte bei der maximalen Bodengeschwindigkeit erzeugen kann. Dies führt zu einer signifikanten Zunahme des seismischen Risikos für Santiago de Chile. KW - Standorteffekte KW - seismisches Rauschen KW - Sedimentbecken KW - Simulation KW - site effects KW - seismic noise KW - sedimentary basin KW - simulation Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-52961 ER - TY - THES A1 - Codutti, Agnese T1 - Behavior of magnetic microswimmers T1 - Verhalten magnetischer Microschwimmer BT - simulations for natural swimmers and synthetic propellers BT - Simulationen von natürlichen Schwimmern und synthetischen Propellern N2 - Microswimmers, i.e. swimmers of micron size experiencing low Reynolds numbers, have received a great deal of attention in the last years, since many applications are envisioned in medicine and bioremediation. A promising field is the one of magnetic swimmers, since magnetism is biocom-patible and could be used to direct or actuate the swimmers. This thesis studies two examples of magnetic microswimmers from a physics point of view. The first system to be studied are magnetic cells, which can be magnetic biohybrids (a swimming cell coupled with a magnetic synthetic component) or magnetotactic bacteria (naturally occurring bacteria that produce an intracellular chain of magnetic crystals). A magnetic cell can passively interact with external magnetic fields, which can be used for direction. The aim of the thesis is to understand how magnetic cells couple this magnetic interaction to their swimming strategies, mainly how they combine it with chemotaxis (the ability to sense external gradient of chemical species and to bias their walk on these gradients). In particular, one open question addresses the advantage given by these magnetic interactions for the magnetotactic bacteria in a natural environment, such as porous sediments. In the thesis, a modified Active Brownian Particle model is used to perform simulations and to reproduce experimental data for different systems such as bacteria swimming in the bulk, in a capillary or in confined geometries. I will show that magnetic fields speed up chemotaxis under special conditions, depending on parameters such as their swimming strategy (run-and-tumble or run-and-reverse), aerotactic strategy (axial or polar), and magnetic fields (intensities and orientations), but it can also hinder bacterial chemotaxis depending on the system. The second example of magnetic microswimmer are rigid magnetic propellers such as helices or random-shaped propellers. These propellers are actuated and directed by an external rotating magnetic field. One open question is how shape and magnetic properties influence the propeller behavior; the goal of this research field is to design the best propeller for a given situation. The aim of the thesis is to propose a simulation method to reproduce the behavior of experimentally-realized propellers and to determine their magnetic properties. The hydrodynamic simulations are based on the use of the mobility matrix. As main result, I propose a method to match the experimental data, while showing that not only shape but also the magnetic properties influence the propellers swimming characteristics. N2 - Die Forschung an Mikroschwimmern oder genauer gesagt an aktiv schwimmenden Mikroorganismen oder Objekten mit niedrigen Reynolds Zahlen, hat in den letzten Jahren wegen ihrer vielfältigen Anwendungen in der Medizin und Bioremediation stark an Bedeutung gewonnen. Besonders vielversprechend ist die Arbeit mit magnetischen Mikroschwimmern, da deren biokompatibler Magnetismus genutzt werden kann um die Schwimmer gezielt zu steuern. In dieser Arbeit werden zwei Beispiele von magnetischen Mikroschwimmern aus physikalischer Sicht untersucht. Das erste Modellsystem hierfür sind magnetische Zellen. Diese können entweder magnetische Biohybride (eine schwimm-Zelle gekoppelt mit einer synthetischen magnetischen Komponente) oder magnetotaktische Bakterien (natürlich vorkommende Bakterien die eine intrazelluläre Kette von magnetischen Kristallen produzieren) sein. Die passive Wechselwirkung der magnetischen Zelle mit einem externen Magnetfeld kann zu deren Steuerung genutzt werden. Das Ziel dieser Arbeit ist es zu verstehen wie magnetische Zellen die magnetische Wechselwirkung mit ihre Schwimmstrategie verknüpfen, oder genauer gesagt, wie sie sie zur Chemotaxis (die Fähigkeit externe chemische Gradienten wahrzunehmen und die Fortbewegungsrichtung daran anzupassen) zu nutzen. Es ist immer noch nicht restlos geklärt worin in der natürlichen Umgebung der magnetischen Bakterien, wie beispielsweise in porösem Sediment, der Vorteil der Wechselwirkung mit dem externen magnetischen Feld liegt. In dieser Arbeit wurde ein modifiziertes „Active Brownian Particle model“ verwendet um mittels Computersimulationen experimentelle Ergebnisse an Bakterien zu reproduzieren, die sich frei, in einer Glaskapillare, oder in anders begrenzten Geometrien bewegen. Ich werde zeigen, dass abhängig von der Schwimmstrategie („run-and-tumble“ oder „runand-reverse“), aerotaktische Strategie (axial oder polar), und der Feldintensität und Orientierung, das magnetische Feld Chemotaxis beschleunigen kann. Abhängig von dem gewählten Modellsystem kann es jedoch auch zu einer Behinderung der Chemotaxis kommen. Das zweite Beispiel für magnetische Mikroschwimmer sind starre (z.B. Helices) oder zufällig geformte magnetische Propeller. Sie werden durch ein externes magnetisches Feld angetrieben und gelenkt. Hierbei stellt sich die Frage wie die Form der Propeller deren Verhalten beeinflusst und wie sie für eine bestimmte Anwendung optimiert werden können. Daher ist es das Ziel dieser Arbeit Simulationsmethoden vorzuschlagen um das experimentell beobachtete Verhalten zu reproduzieren und die magnetischen Eigenschaften der Propeller zu beschreiben. Hierfür wird die Mobilitätsmatrix verwendet um die hydrodynamischen Simulationen zu realisieren. Ein Hauptresultat meiner Arbeit ist eine neue Methode, welche die Simulationen in Einklang mit den experimentellen Resultaten bringt. Hierbei zeigt sich, dass nicht nur die Form sondern insbesondere auch die magnetischen Eigenschaften die Schwimmcharakteristik der Propeller entscheidend beeinflussen. KW - microswimmers KW - magnetism KW - bacteria KW - propellers KW - simulation KW - Microschwimmer KW - Magnetismus KW - Bakterien KW - Propeller KW - Simulationen Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-422976 ER - TY - THES A1 - Moreira, André Guérin T1 - Charged systems in bulk and at interfaces N2 - Eine der Faustregeln der Kolloid- und Oberflächenphysik ist, dass die meisten Oberflächen geladen sind, wenn sie mit einem Lösungsmittel, normalerweise Wasser, in Kontakt treten. Dies ist zum Beispiel bei ladungsstabilisierten Kolloidalen Suspensionen der Fall, bei denen die Oberfläche der Kolloidteilchen geladen ist (gewöhnlich mit einer Ladung von mehreren Hunderttausend Elementarladungen), oder bei Monoschichten ionischer Tenside, die auf einer Luft-Wasser Grenzfläche sitzen (wobei die wasserliebenden Kopfgruppen durch die Freisetzung von Gegenionen geladen werden), sowie bei Doppelschichten, die geladene phospholipide enthalten (wie Zellmembranen). In dieser Arbeit betrachten wir einige Modellsysteme, die zwar eine vereinfachte Fassung der Realität darstellen, von denen wir aber dennoch erwarten koennen, dass wir mit ihrer Hilfe einige physikalische Eigenschaften realer geladener Systeme (Kolloide und Elektrolyte) einfangen können. N2 - One of the rules-of-thumb of colloid and surface physics is that most surfaces are charged when in contact with a solvent, usually water. This is the case, for instance, in charge-stabilized colloidal suspensions, where the surface of the colloidal particles are charged (usually with a charge of hundreds to thousands of e, the elementary charge), monolayers of ionic surfactants sitting at an air-water interface (where the water-loving head groups become charged by releasing counterions), or bilayers containing charged phospholipids (as cell membranes). In this work, we look at some model-systems that, although being a simplified version of reality, are expected to capture some of the physical properties of real charged systems (colloids and electrolytes). We initially study the simple double layer, composed by a charged wall in the presence of its counterions. The charges at the wall are smeared out and the dielectric constant is the same everywhere. The Poisson-Boltzmann (PB) approach gives asymptotically exact counterion density profiles around charged objects in the weak-coupling limit of systems with low-valent counterions, surfaces with low charge density and high temperature (or small Bjerrum length). Using Monte Carlo simulations, we obtain the profiles around the charged wall and compare it with both Poisson-Boltzmann (in the low coupling limit) and the novel strong coupling (SC) theory in the opposite limit of high couplings. In the latter limit, the simulations show that the SC leads in fact to asymptotically correct density profiles. We also compare the Monte Carlo data with previously calculated corrections to the Poisson-Boltzmann theory. We also discuss in detail the methods used to perform the computer simulations. After studying the simple double layer in detail, we introduce a dielectric jump at the charged wall and investigate its effect on the counterion density distribution. As we will show, the Poisson-Boltzmann description of the double layer remains a good approximation at low coupling values, while the strong coupling theory is shown to lead to the correct density profiles close to the wall (and at all couplings). For very large couplings, only systems where the difference between the dielectric constants of the wall and of the solvent is small are shown to be well described by SC. Another experimentally relevant modification to the simple double layer is to make the charges at the plane discrete. The counterions are still assumed to be point-like, but we constraint the distance of approach between ions in the plane and counterions to a minimum distance D. The ratio between D and the distance between neighboring ions in the plane is, as we will see, one of the important quantities in determining the influence of the discrete nature of the charges at the wall over the density profiles. Another parameter that plays an important role, as in the previous case, is the coupling as we will demonstrate, systems with higher coupling are more subject to discretization effects than systems with low coupling parameter. After studying the isolated double layer, we look at the interaction between two double layers. The system is composed by two equally charged walls at distance d, with the counterions confined between them. The charge at the walls is smeared out and the dielectric constant is the same everywhere. Using Monte-Carlo simulations we obtain the inter-plate pressure in the global parameter space, and the pressure is shown to be negative (attraction) at certain conditions. The simulations also show that the equilibrium plate separation (where the pressure changes from attractive to repulsive) exhibits a novel unbinding transition. We compare the Monte Carlo results with the strong-coupling theory, which is shown to describe well the bound states of systems with moderate and high couplings. The regime where the two walls are very close to each other is also shown to be well described by the SC theory. Finally, Using a field-theoretic approach, we derive the exact low-density ("virial") expansion of a binary mixture of positively and negatively charged hard spheres (two-component hard-core plasma, TCPHC). The free energy obtained is valid for systems where the diameters d_+ and d_- and the charge valences q_+ and q_- of positive and negative ions are unconstrained, i.e., the same expression can be used to treat dilute salt solutions (where typically d_+ ~ d_- and q_+ ~ q_-) as well as colloidal suspensions (where the difference in size and valence between macroions and counterions can be very large). We also discuss some applications of our results. KW - geladene Systeme KW - elektrische Doppelschicht KW - Elektrolyte KW - Theorie KW - Simulation KW - charged systems KW - electric double layer KW - electrolytes KW - theory KW - simulation Y1 - 2001 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0000677 ER - TY - THES A1 - Panzer, Marcel T1 - Design of a hyper-heuristics based control framework for modular production systems T1 - Design eines auf Hyperheuristiken basierenden Steuerungsframeworks für modulare Produktionssysteme N2 - Volatile supply and sales markets, coupled with increasing product individualization and complex production processes, present significant challenges for manufacturing companies. These must navigate and adapt to ever-shifting external and internal factors while ensuring robustness against process variabilities and unforeseen events. This has a pronounced impact on production control, which serves as the operational intersection between production planning and the shop- floor resources, and necessitates the capability to manage intricate process interdependencies effectively. Considering the increasing dynamics and product diversification, alongside the need to maintain constant production performances, the implementation of innovative control strategies becomes crucial. In recent years, the integration of Industry 4.0 technologies and machine learning methods has gained prominence in addressing emerging challenges in production applications. Within this context, this cumulative thesis analyzes deep learning based production systems based on five publications. Particular attention is paid to the applications of deep reinforcement learning, aiming to explore its potential in dynamic control contexts. Analysis reveal that deep reinforcement learning excels in various applications, especially in dynamic production control tasks. Its efficacy can be attributed to its interactive learning and real-time operational model. However, despite its evident utility, there are notable structural, organizational, and algorithmic gaps in the prevailing research. A predominant portion of deep reinforcement learning based approaches is limited to specific job shop scenarios and often overlooks the potential synergies in combined resources. Furthermore, it highlights the rare implementation of multi-agent systems and semi-heterarchical systems in practical settings. A notable gap remains in the integration of deep reinforcement learning into a hyper-heuristic. To bridge these research gaps, this thesis introduces a deep reinforcement learning based hyper- heuristic for the control of modular production systems, developed in accordance with the design science research methodology. Implemented within a semi-heterarchical multi-agent framework, this approach achieves a threefold reduction in control and optimisation complexity while ensuring high scalability, adaptability, and robustness of the system. In comparative benchmarks, this control methodology outperforms rule-based heuristics, reducing throughput times and tardiness, and effectively incorporates customer and order-centric metrics. The control artifact facilitates a rapid scenario generation, motivating for further research efforts and bridging the gap to real-world applications. The overarching goal is to foster a synergy between theoretical insights and practical solutions, thereby enriching scientific discourse and addressing current industrial challenges. N2 - Volatile Beschaffungs- und Absatzmärkte sowie eine zunehmende Produktindividualisierung konfrontieren Fertigungsunternehmen mit beträchtlichen Herausforderungen. Diese erfordern eine Anpassung der Produktion an sich ständig wechselnde externe Einflüsse und eine hohe Prozessrobustheit gegenüber unvorhersehbaren Schwankungen. Ein Schlüsselelement in diesem Kontext ist die Produktionssteuerung, die als operative Schnittstelle zwischen der Produktions- planung und den Fertigungsressourcen fungiert und eine effiziente Handhabung zahlreicher Prozessinterdependenzen sicherstellen muss. Angesichts dieser gesteigerten Produktionsdynamik und Produktvielfalt rücken innovative Steuerungsansätze in den Vordergrund. In jüngerer Zeit wurden daher verstärkt Industrie-4.0-Ansätze und Methoden des maschinellen Lernens betrachtet. Im Kontext der aktuellen Forschung analysiert die vorliegende kumulative Arbeit Deep-Learning basierte Produktionssysteme anhand von fünf Publikationen. Hierbei wird ein besonderes Augenmerk auf die Anwendungen des Deep Reinforcement Learning gelegt, um dessen Potenzial zu ergründen. Die Untersuchungen zeigen, dass das Deep Reinforcement Learning in vielen Produktionsanwendungen sowohl herkömmlichen Ansätzen als auch an- deren Deep-Learning Werkzeugen überlegen ist. Diese Überlegenheit ergibt sich vor allem aus dem interaktiven Lernprinzip und der direkten Interaktion mit der Umwelt, was es für die dynamische Produktionssteuerung besonders geeignet macht. Dennoch werden strukturelle, organisatorische und algorithmische Forschungslücken identifiziert. Die überwiegende Mehrheit der untersuchten Ansätze fokussiert sich auf Werkstattfertigungen und vernachlässigt dabei potenzielle Prozesssynergien modularer Produktionssysteme. Ferner zeigt sich, dass Multi- Agenten- und Mehr-Ebenen-Systeme sowie die Kombination verschiedener algorithmischer Ansätze nur selten zur Anwendung kommen. Um diese Forschungslücken zu adressieren, wird eine auf Deep Reinforcement Learning basierende Hyper-Heuristik für die Steuerung modularer Produktionssysteme vorgestellt, die nach der Design Science Research Methodology entwickelt wird. Ein semi-heterarchisches Multi-Agenten-System ermöglicht eine dreifache Reduktion der Steuerungs- und Optimierungs- komplexität und gewährleistet gleichzeitig eine hohe Systemadaptabilität und -robustheit. In Benchmarks übertrifft das Steuerungskonzept regelbasierte Ansätze, minimiert Durchlaufzeiten und Verspätungen und berücksichtigt kunden- sowie auftragsorientierte Kennzahlen. Die ent- wickelte Steuerungsmethodik ermöglicht einen schnellen Szenarienentwurf, um dadurch weitere Forschungsbemühungen zu stimulieren und die bestehende Transferlücke zur Realität weiter zu überbrücken. Das Ziel dieser Forschungsarbeit ist es, eine Synergie zwischen theoretischen Erkenntnissen und Praxis-relevanten Lösungen zu schaffen, um sowohl den wissenschaftlichen Diskurs zu bereichern als auch Antworten auf aktuelle industrielle Herausforderungen zu bieten. KW - modular production KW - deep learning KW - modulare Produktion KW - Produktionssteuerung KW - Deep Learning KW - Reinforcement Learning KW - Simulation KW - production control KW - reinforcement learning KW - simulation Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-633006 ER - TY - THES A1 - Konon, Alexander T1 - Essays on career choice under risk and ambiguity T1 - Essays über Karrierewahl unter Risiko und Unsicherheit N2 - This dissertation consists of five self-contained essays, addressing different aspects of career choices, especially the choice of entrepreneurship, under risk and ambiguity. In Chapter 2, the first essay develops an occupational choice model with boundedly rational agents, who lack information, receive noisy feedback, and are restricted in their decisions by their personality, to analyze and explain puzzling empirical evidence on entrepreneurial decision processes. In the second essay, in Chapter 3, I contribute to the literature on entrepreneurial choice by constructing a general career choice model on the basis of the assumption that outcomes are partially ambiguous. The third essay, in Chapter 4, theoretically and empirically analyzes the impact of media on career choices, where information on entrepreneurship provided by the media is treated as an informational shock affecting prior beliefs. The fourth essay, presented in Chapter 5, contains an empirical analysis of the effects of cyclical macro variables (GDP and unemployment) on innovative start-ups in Germany. In the fifth, and last, essay in Chapter 6, we examine whether information on personality is useful for advice, using the example of career advice. N2 - Diese Dissertation besteht aus fünf eigenständigen Aufsätzen, die sich mit verschiedenen Aspekten von Berufswahl, insbesondere der Wahl von Entrepreneurship, unter Risiko und Unsicherheit befassen. In Kapitel 2 entwickelt der erste Aufsatz ein Berufswahlmodell mit begrenzt-rationalen Agenten, die eingeschränkte Information haben, Feedback mit Rauschkomponenten erhalten und in ihren Entscheidungen durch ihre Persönlichkeit eingeschränkt sind, um einige bisher unerklärte Charakteristika von unternehmerischen Entscheidungsprozessen zu analysieren und zu erklären. Im zweiten Aufsatz in Kapitel 3 wird die Literatur zur Karrierewahl durch eine neue Perspektive ergänzt. Der Aufsatz konstruiert ein allgemeines Modell auf der Grundlage der Annahme, dass Entscheidungsergebnisse (teilweise) unsicher sind. Der dritte Aufsatz in Kapitel 4 analysiert theoretisch und empirisch die Auswirkung von Medien auf Berufsentscheidungen. Informationen über Entrepreneurship, die von den Medien zur Verfügung gestellt werden, werden als Informationsschocks behandelt, die vorherige Überzeugungen beeinflussen. Der vierte Aufsatz, der in Kapitel 5 vorgestellt wird, enthält eine empirische Analyse der Auswirkungen von zyklischen, regionalen Makrovariablen (Bruttoinlandsprodukt und Arbeitslosigkeit) auf innovative Start-Ups in Deutschland. Im fünften und letzten Aufsatz in Kapitel 6 untersuchen wir am Beispiel der Berufsberatung, ob Informationen über die Persönlichkeit für Vorhersagen und Empfehlungen nützlich sind. KW - ambiguity KW - entrepreneurship KW - Bayesian learning KW - simulation KW - Unsicherheit KW - Entrepreneurship KW - Bayes'sches Lernen KW - Simulationsmodelle Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-416466 ER - TY - THES A1 - Wagner, Anja T1 - Konzeption und Aufbau eines Geoinformationssystems zur Modellierung und Simulation von Offenlandschaften N2 - Zwischen 1990 und 1994 wurden rund 1000 Liegenschaften, die in der ehemaligen DDR von der Sowjetarmee und der NVA für militärische Übungen genutzt wurden, an Bund und Länder übergeben. Die größten Truppenübungsplätze liegen in Brandenburg und sind heute teilweise in Großschutzgebiete integriert, andere Plätze werden von der Bundeswehr weiterhin aktiv genutzt. Aufgrund des militärischen Betriebs sind die Böden dieser Truppenübungsplätze oft durch Blindgänger, Munitionsreste, Treibstoff- und Schmierölreste bis hin zu chemischen Kampfstoffen belastet. Allerdings existieren auf fast allen Liegenschaften neben diesen durch Munition und militärische Übungen belasteten Bereichen auch naturschutzfachlich wertvolle Flächen; gerade in den Offenlandbereichen kann dies durchaus mit einer Belastung durch Kampfmittel einhergehen. Charakteristisch für diese offenen Flächen, zu denen u.a. Zwergstrauchheiden, Trockenrasen, wüstenähnliche Sandflächen und andere nährstoffarme baumlose Lebensräume gehören, sind Großflächigkeit, Abgeschiedenheit sowie ihre besondere Nutzung und Bewirtschaftung, d.h. die Abwesenheit von land- und forstwirtschaftlichem Betrieb sowie von Siedlungsflächen. Diese Charakteristik war die Grundlage für die Entwicklung einer speziell angepassten Flora und Fauna. Nach Beendigung des Militärbetriebs setzte dann in weiten Teilen eine großflächige Sukzession – die allmähliche Veränderung der Zusammensetzung von Pflanzen- und Tiergesellschaften – ein, die diese offenen Bereiche teilweise bereits in Wald verwandelte und somit verschwinden ließ. Dies wiederum führte zum Verlust der an diese Offenlandflächen gebundenen Tier- und Pflanzenarten. Zur Erhaltung, Gestaltung und Entwicklung dieser offenen Flächen wurden daher von einer interdisziplinären Gruppe von Naturwissenschaftlern verschiedene Methoden und Konzepte auf ihre jeweilige Wirksamkeit untersucht. So konnten schließlich die für die jeweiligen Standortbedingungen geeigneten Maßnahmen eingeleitet werden. Voraussetzung für die Einleitung der Maßnahmen sind zum einen Kenntnisse zu diesen jeweiligen Standortbedingungen, d.h. zum Ist-Zustand, sowie zur Entwicklung der Flächen, d.h. zur Dynamik. So kann eine Abschätzung über die zukünftige Flächenentwicklung getroffen werden, damit ein effizienter Maßnahmeneinsatz stattfinden kann. Geoinformationssysteme (GIS) spielen dabei eine entscheidende Rolle zur digitalen Dokumentation der Biotop- und Nutzungstypen, da sie die Möglichkeit bieten, raum- und zeitbezogene Geometrie- und Sachdaten in großen Mengen zu verarbeiten. Daher wurde ein fachspezifisches GIS für Truppenübungsplätze entwickelt und implementiert. Die Aufgaben umfassten die Konzeption der Datenbank und des Objektmodells sowie fachspezifischer Modellierungs-, Analyse- und Präsentationsfunktionen. Für die Integration von Fachdaten in die GIS-Datenbank wurde zudem ein Metadatenkatalog entwickelt, der in Form eines zusätzlichen GIS-Tools verfügbar ist. Die Basisdaten für das GIS wurden aus Fernerkundungsdaten, topographischen Karten sowie Geländekartierungen gewonnen. Als Instrument für die Abschätzung der zukünftigen Entwicklung wurde das Simulationstool AST4D entwickelt, in dem sowohl die Nutzung der (Raster-)Daten des GIS als Ausgangsdaten für die Simulationen als auch die Nutzung der Simulationsergebnisse im GIS möglich ist. Zudem können die Daten in AST4D raumbezogen visualisiert werden. Das mathematische Konstrukt für das Tool war ein so genannter Zellulärer Automat, mit dem die Flächenentwicklung unter verschiedenen Voraussetzungen simuliert werden kann. So war die Bildung verschiedener Szenarien möglich, d.h. die Simulation der Flächenentwicklung mit verschiedenen (bekannten) Eingangsparametern und den daraus resultierenden unterschiedlichen (unbekannten) Endzuständen. Vor der Durchführung einer der drei in AST4D möglichen Simulationsstufen können angepasst an das jeweilige Untersuchungsgebiet benutzerspezifische Festlegungen getroffen werden. N2 - Between 1990 and 1994 more than a thousand military properties in East Germany used for military exercise by the Soviet army and the East German forces were handed over to government institutions of the national state and federal states (Laender), respectively. The largest military training areas are located in the federal state of Brandenburg. Some of these are, by now, part of environmentally protected areas, others are still being used by the German forces. As a result of long-lasting military operations the soils of these areas are heavily polluted by ammunition, duds, fuel and lubricants as well as a range of chemicals. Due to these special environmental conditions specifically adapted vegetation and fauna developed in these environments which make these areas valuable from an environmental protection perspective. Unlike other environments in North West Germany these former military training areas are characterised by wideness, separateness as well as the absence of agricultural, forest and settlement land use. This allowed for the development of a characteristic vegetation cover composed of dwarf bush heaths, drying lawns, desert-like sand surfaces and other nutrient-poor treeless habitats. Following the end of military use the process of succession – a gradual change of flora and fauna over space and time – set in. More a than a decade later the former open plains have, in part, developed into forests. The loss of open range land effected the disappearance of adapted animal and plant populations. To retain, preserve and develop these environmentally valuable areas different methods and concepts were examined for the respective effectiveness by multi-disciplinary group of scientists. Prerequisites of the application of methods to preserve the open plains are up-to-date knowledge of local conditions as well as in-depth understanding of the land surface developments and their dynamics, in particular. Based on this expertise the future surface development of these areas can be estimated which, in term, is a prerequisite for selecting the appropriate methods. Geo information systems (GIS) play an important role for the digital documentation and monitoring of biotopes, land use etc as they provide for acquisition, processing and storage of mass geo data including their locational and feature attributes. To make this GIS functionality available for the management and development of former military training areas a dedicated GIS has been developed and implemented. Tasks tackled included a database concept and object model as well as application-specific modelling, analysis and map presentation functions. Integration of relevant spatial and attribute data into this system required a meta data catalogue made available as an add-on GIS tool. Topographic base data for GIS input were taken from remote sensing imagery, topographic maps and additional field surveys. To simulate the development of the former military areas over space and time a specific simulation tool had to be developed as conventional GIS lack dynamic functionalities. The AST4D tool enables the user to utilise existing GIS data. Processed results, in term, can then be used within the GIS application. Additionally AST4D data may be visualised in map form. The AST4D GIS tool is based on the mathematical model of cellular automata. This model allows for the user-defined setting of status quo and simulation of future developments under different input parameters and target conditions. KW - Truppenübungsplatz KW - Offenland KW - Modellierung KW - Analyse KW - Landscape Metrics KW - Simulation KW - Szenarienbildung KW - Zellulärer Automat KW - military plains KW - open range KW - modelling KW - analysis KW - landscape metrics KW - simulation KW - scenarios KW - cellular automata Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0001411 ER - TY - THES A1 - Michalczyk, Anna T1 - Modelling of nitrogen cycles in intensive winter wheat–summer maize double cropping systems in the North China Plain T1 - Modellierung von Stickstoffkreisläufen in intensiven Winterweizen–Sommermais-Doppelfruchtfolgen in der Nordchinesischen Tiefebene BT - site specific optimisation of nitrogen fertilisation with regard to nitrogen losses, water protection, productivity and regionalisation N2 - The North China Plain (NCP) is one of the most productive and intensive agricultural regions in China. High doses of mineral nitrogen (N) fertiliser, often combined with flood irrigation, are applied, resulting in N surplus, groundwater depletion and environmental pollution. The objectives of this thesis were to use the HERMES model to simulate the N cycle in winter wheat (Triticum aestivum L.)–summer maize (Zea mays L.) double crop rotations and show the performance of the HERMES model, of the new ammonia volatilisation sub-module and of the new nitrification inhibition tool in the NCP. Further objectives were to assess the models potential to save N and water on plot and county scale, as well as on short and long-term. Additionally, improved management strategies with the help of a model-based nitrogen fertiliser recommendation (NFR) and adapted irrigation, should be found. Results showed that the HERMES model performed well under growing conditions of the NCP and was able to describe the relevant processes related to soil–plant interactions concerning N and water during a 2.5 year field experiment. No differences in grain yield between the real-time model-based NFR and the other treatments of the experiments on plot scale in Quzhou County could be found. Simulations with increasing amounts of irrigation resulted in significantly higher N leaching, higher N requirements of the NFR and reduced yields. Thus, conventional flood irrigation as currently practised by the farmers bears great uncertainties and exact irrigation amounts should be known for future simulation studies. In the best-practice scenario simulation on plot-scale, N input and N leaching, but also irrigation water could be reduced strongly within 2 years. Thus, the model-based NFR in combination with adapted irrigation had the highest potential to reduce nitrate leaching, compared to farmers practice and mineral N (Nmin)-reduced treatments. Also the calibrated and validated ammonia volatilisation sub-module of the HERMES model worked well under the climatic and soil conditions of northern China. Simple ammonia volatilisation approaches gave also satisfying results compared to process-oriented approaches. During the simulation with Ammonium sulphate Nitrate with nitrification inhibitor (ASNDMPP) ammonia volatilisation was higher than in the simulation without nitrification inhibitor, while the result for nitrate leaching was the opposite. Although nitrification worked well in the model, nitrification-born nitrous oxide emissions should be considered in future. Results of the simulated annual long-term (31 years) N losses in whole Quzhou County in Hebei Province were 296.8 kg N ha−1 under common farmers practice treatment and 101.7 kg N ha−1 under optimised treatment including NFR and automated irrigation (OPTai). Spatial differences in simulated N losses throughout Quzhou County, could only be found due to different N inputs. Simulations of an optimised treatment, could save on average more than 260 kg N ha−1a−1 from fertiliser input and 190 kg N ha−1a−1 from N losses and around 115.7 mm a−1 of water, compared to farmers practice. These long-term simulation results showed lower N and water saving potential, compared to short-term simulations and underline the necessity of long-term simulations to overcome the effect of high initial N stocks in soil. Additionally, the OPTai worked best on clay loam soil except for a high simulated denitrification loss, while the simulations using farmers practice irrigation could not match the actual water needs resulting in yield decline, especially for winter wheat. Thus, a precise adaption of management to actual weather conditions and plant growth needs is necessary for future simulations. However, the optimised treatments did not seem to be able to maintain the soil organic matter pools, even with full crop residue input. Extra organic inputs seem to be required to maintain soil quality in the optimised treatments. HERMES is a relatively simple model, with regard to data input requirements, to simulate the N cycle. It can offer interpretation of management options on plot, on county and regional scale for extension and research staff. Also in combination with other N and water saving methods the model promises to be a useful tool. N2 - Die Nordchinesische Tiefebene (NCP) ist eine der produktivsten und intensivsten Agrarregionen Chinas. Große Düngermengen an mineralischem Stickstoff (N) und der oft in Kombination genutzten Überflutungsbewässerung führen zu Stickstoffüberflüssen, Grundwasserabsenkung und Umweltverschmutzung. Ziel dieser Arbeit war die Simulation des N-Kreislaufes in Winterweizen (Triticum aestivum L.)–Sommermais (Zea mays L.) -Doppelfruchtfolgen mit dem HERMES Modell. Weitere Ziele waren ein Test der Modellgüte, sowie das Potential des Modells aufzuzeigen, N und Wasser mit Hilfe einer modellbasierten N-Düngeempfehlung (NFR) und angepassten Bewässerungsstrategien einzusparen. Dies erfolgte auf Schlag- und Countyebene wie auch in Kurzzeit- und in Langzeitsimulationen, um verbesserte Managementstrategien für Quzhou-County in der Hebei-Provinz zu finden. Die Ergebnisse zeigten, dass das HERMES Modell gut unter den Wachstumsbedingungen der NCP funktioniert und alle relevanten Boden-Pflanze-Interaktionen während der Versuchszeit von 2,5 Jahren in Bezug auf N und Wasser beschreiben konnte. Es konnten keine Ertragsunterschiede zwischen Echtzeit modellbasierter NFR und anderen Behandlungen auf Schlagebene in Quzhou-County festgestellt werden. Simulationen mit steigenden Bewässerungsgaben ergaben signifikant höheren N-Austrag, höheren N-Bedarf der NFR und reduzierte Erträge. Daher birgt die konventionelle Überflutungsbewässerung, wie sie derzeit von den Landwirten praktiziert wird, große Unsicherheiten und genaue Bewässerungsmengen sollten für zukünftige Simulationsstudien bekannt sein. In der optimierten („best-practice“) Szenariosimulation auf Schlagebene konnte insbesondere die N-Düngung und der N-Austrag, aber auch die Bewässerung innerhalb 2 Jahre stark gesenkt werden. Daher hat die modellbasierte NFR in Kombination mit angepasster Bewässerung, im Gegensatz zu konventioneller und mineralischen N (Nmin)-reduzierter Behandlung, das höchste Potential Nitratauswaschung zu reduzieren. Auch das kalibrierte und validierte Ammoniak-Verflüchtigungs-modul des HERMES Modells funktionierte gut unter den Klima- und Bodenverhältnissen in Nordchina. Die zwei einfacheren Ammoniak-Verflüchtigungsansätze erreichten auch gute Ergebnisse, während die zwei prozessorientierten Ansätze Umwelteinflüsse besser darstellen konnten. In der Simulation mit der Ammonsulfatsalpeter-Düngung mit Nitrifikationsinhibitor (ASNDMPP) war die Ammoniakverflüchtigung höher als in der Simulation ohne Nitrifikationshemmer, während das Ergebnis für Nitratauswaschung umgekehrt war. Obwohl der Nitrifikationsansatz gut funktionierte, sollten von der Nitrifikation stammende Lachgasemissionen in Zukunft im Modell berücksichtigt werden. Im Jahresdurchschnitt lagen die simulierten Langzeit (31 Jahre) N-Verluste für eine Weizen-Mais-Doppelfruchtfolge im ganzen Quzhou-County bei 296,8 kg N ha−1 unter konventioneller Düngung und bei 101,7 kg N ha−1 unter optimierter Düngung inklusive NFR and automatischer Bewässerung (OPTai). Räumliche Unterschiede von simulierten N-Verlusten in Quzhou-County konnten nur aufgrund von unterschiedlichen N-Düngemengen gefunden werden. Simulationen einer optimierten Behandlung konnten im Durchschnitt mehr als 260 kg N ha−1a−1 an N-Düngung und 190 kg N ha−1a−1 an N-Verlusten und 115,7 mm a−1 an Wasser, im Vergleich zur konventionellen Behandlung, einsparen. Im Vergleich zu den Kurzzeitsimulationen ist es ein niedrigeres N- und Wasserreduktionspotential und unterstreicht die Notwendigkeit von Langzeitsimulationen um den Effekt von hohen Anfangs Nmin-Gehalten im Boden zu berücksichtigen. Zudem kommt, dass auf tonigem Lehm Simulationen mit konventioneller Bewässerung nicht den aktuellen Wasserbedarf decken konnten, welches zu Ertragseinbußen insbesondere für Winterweizen führte. Die OPTai Behandlung funktionierte bis auf hohe simulierte Denitrifikationsverluste auf diesem Standort am besten. Daher ist dort für zukünftige Simulationen ein an aktuelle Wetterverhältnisse und Pflanzenwachstumsbedürfnisse angepasstes Management von N und Wasser nötig. Trotzdem schienen die optimierten Behandlungen, trotz voller Strohrückgabe, die organische Bodensubstanz nicht zu erhalten. Zur Sicherung der Bodenfruchtbarkeit in den optimierten Behandlungen scheinen zusätzliche organische Düngergaben wahrscheinlich notwendig zu sein. HERMES ist ein relativ einfaches Modell, im Hinblick auf die Anforderungen an die Eingangsdaten, um den Stickstoffkreislauf zu simulieren. Es ermöglicht, Managementoptionen für Berater und Wissenschaftler auf Schlag-, County- und Regionalebene anzuwenden. Auch in Kombination mit anderen N- und Wasser-Einsparmethoden verspricht das Modell ein nützliches Instrument zu sein. KW - nitrogen KW - Stickstoff KW - simulation KW - Simulation KW - China KW - China Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-444213 ER - TY - THES A1 - Schröder, Sarah T1 - Modelling surface evolution coupled with tectonics T1 - Modellierung von Oberflächenprozessen gekoppelt mit Tektonik BT - A case study for the Pamir BT - Eine Fallstudie zum Pamir N2 - This study presents the development of 1D and 2D Surface Evolution Codes (SECs) and their coupling to any lithospheric-scale (thermo-)mechanical code with a quadrilateral structured surface mesh. Both SECs involve diffusion as approach for hillslope processes and the stream power law to reflect riverbed incision. The 1D SEC settles sediment that was produced by fluvial incision in the appropriate minimum, while the supply-limited 2D SEC DANSER uses a fast filling algorithm to model sedimantation. It is based on a cellular automaton. A slope-dependent factor in the sediment flux extends the diffusion equation to nonlinear diffusion. The discharge accumulation is achieved with the D8-algorithm and an improved drainage accumulation routine. Lateral incision enhances the incision's modelling. Following empirical laws, it incises channels of several cells width. The coupling method enables different temporal and spatial resolutions of the SEC and the thermo-mechanical code. It transfers vertical as well as horizontal displacements to the surface model. A weighted smoothing of the 3D surface displacements is implemented. The smoothed displacement vectors transmit the deformation by bilinear interpolation to the surface model. These interpolation methods ensure mass conservation in both directions and prevent the two surfaces from drifting apart. The presented applications refer to the evolution of the Pamir orogen. A calibration of DANSER's parameters with geomorphological data and a DEM as initial topography highlights the advantage of lateral incision. Preserving the channel width and reflecting incision peaks in narrow channels, this closes the huge gap between current orogen-scale incision models and observed topographies. River capturing models in a system of fault-bounded block rotations reaffirm the importance of the lateral incision routine for capturing events with channel initiation. The models show a low probability of river capturings with large deflection angles. While the probability of river capturing is directly depending on the uplift rate, the erodibility inside of a dip-slip fault speeds up headward erosion along the fault: The model's capturing speed increases within a fault. Coupling DANSER with the thermo-mechanical code SLIM 3D emphasizes the versatility of the SEC. While DANSER has minor influence on the lithospheric evolution of an indenter model, the brittle surface deformation is strongly affected by its sedimentation, widening a basin in between two forming orogens and also the southern part of the southern orogen to south, east and west. N2 - Im Rahmen dieser Studie werden 1D und 2D Erosionsmodelle im Gebirgsmaßstab implementiert und mit Modellen für tektonische Deformation gekoppelt. Die Kopplungsmethode erlaubt unterschiedlich räumliche und zeitliche Auflösungen im tektonischen und im Erosionsmodell. Es werden sowohl vertikale als auch horizontale Bewegungen zwischen den Modellen transferiert. Darüber hinaus enthält die Kopplungsmethode ein Glättungsverfahren, um eventuelle Instabilitäten des tektonischen Modelles zu kompensieren. Beide Erosionsmodelle beziehen Hangerosion, Flusseinschneidung und Sedimentation ein. Der 1D Code nutzt Hack's Law, um die Wassermengen zu berechnen. Er garantiert Massenerhaltung, indem er Sedimente in Senken speichert. Das 2D Erosionsmodell DANSER basiert auf einem zellulären Automaten. Ein zusätzlicher steigungsabhängiger Faktor erweitert lineare zu nichtlinearer Diffusion. Wassermengen werden mit Hilfe des D8-Algorithmus und einer veränderten Form von O'Callaghans (1984) Algorithmus akkumuliert. Laterale Einschneidung, berechnet durch einen neuen Verteilungs-Algorithmus, verbessert die Modellierung von Flusssystemen. Flüsse sind dabei repräsentiert durch eine unterschiedliche Anzahl an Zellen orthogonal zur Fließrichtung. Ihre Breite wird nach empirischen Gesetzen ermittelt. Die präsentierten Anwendungen dienen der Studie des Pamirgebirges. Zunächst werden die Modellparameter anhand von Einschneidungs- und Erosionsraten sowie Sedimentdurchflüssen kalibriert. Ein digitales Höhenmodell dient als Anfangstopographie und zur Extraktion von Flussprofilen. Laterale Einschneidung zeigt eine deutliche Verbesserung zu bisher vorhandenen Modellen. Sie ermöglicht die Erhaltung der Flussbreite und zeigt hohe Einschneidungsraten in engen Flusspassagen. Modelle von Flussanzapfungen in einem System paralleler Verwerfungen bestätigen die Wichtigkeit von lateraler Einschneidung für Flussanzapfungsmodelle, die Hangerosion einbeziehen. Während die Modelle eine geringe Wahrscheinlichkeit von Flussanzapfungen mit hohem Ablenkungswinkel zeigen, belegen sie auch, dass deren (allgemeine) Wahrscheinlichkeit direkt von der Hebungsrate der Verwerfungen abhängt. Die Erodibilität beschleunigt lediglich die Geschwindigkeit von Flussanzapfungen. Ein Modell, das die Codes SLIM 3D und DANSER koppelt, dokumentiert die vielseitige Verwendbarkeit des neuen Codes: Es zeigt einen geringen Einfluss von Oberflächenprozessen auf die Lithosphärendeformation, während die Sedimentationsroutine erheblich auf spröde Oberflächendeformationen einwirkt. Das Modell legt nahe, dass Sedimentation ein zwischen zwei entstehenden Gebirgen gelegenes Becken weitet. Außerdem weitet sich der südlich von der interkontinentalen Kollisionszone gelegene Teil des Gebirge-Models ebenfalls durch Sedimentation. KW - erosion KW - coupling KW - SEC KW - surface evolution KW - thermo-mechanics KW - surface processes KW - DANSER KW - Pamir KW - Tien-Shan KW - Tian-Shan KW - tectonics KW - modelling KW - modeling KW - numerical model KW - simulation KW - surface KW - fluvial incision KW - hillslope diffusion KW - finite differences KW - finite elements KW - Eulerian grid KW - DANSER KW - DANSER KW - Erosion KW - Modellierung KW - Tektonik KW - Koppelung KW - SEC KW - numerische Modellierung KW - Oberflächenprozesse KW - Pamir KW - Tien-Shan KW - Tian-Shan KW - Tiefendeformation KW - Software KW - Simulation KW - Oberfläche KW - fluviale Einschneidung KW - Hangerosion KW - finite Differenzen KW - finite Elemente KW - Eulerische Gitter Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-90385 ER - TY - THES A1 - Šustr, David T1 - Molecular diffusion in polyelectrolyte multilayers N2 - Research on novel and advanced biomaterials is an indispensable step towards their applications in desirable fields such as tissue engineering, regenerative medicine, cell culture, or biotechnology. The work presented here focuses on such a promising material: polyelectrolyte multilayer (PEM) composed of hyaluronic acid (HA) and poly(L-lysine) (PLL). This gel-like polymer surface coating is able to accumulate (bio-)molecules such as proteins or drugs and release them in a controlled manner. It serves as a mimic of the extracellular matrix (ECM) in composition and intrinsic properties. These qualities make the HA/PLL multilayers a promising candidate for multiple bio-applications such as those mentioned above. The work presented aims at the development of a straightforward approach for assessment of multi-fractional diffusion in multilayers (first part) and at control of local molecular transport into or from the multilayers by laser light trigger (second part). The mechanism of the loading and release is governed by the interaction of bioactives with the multilayer constituents and by the diffusion phenomenon overall. The diffusion of a molecule in HA/PLL multilayers shows multiple fractions of different diffusion rate. Approaches, that are able to assess the mobility of molecules in such a complex system, are limited. This shortcoming motivated the design of a novel evaluation tool presented here. The tool employs a simulation-based approach for evaluation of the data acquired by fluorescence recovery after photobleaching (FRAP) method. In this approach, possible fluorescence recovery scenarios are primarily simulated and afterwards compared with the data acquired while optimizing parameters of a model until a sufficient match is achieved. Fluorescent latex particles of different sizes and fluorescein in an aqueous medium are utilized as test samples validating the analysis results. The diffusion of protein cytochrome c in HA/PLL multilayers is evaluated as well. This tool significantly broadens the possibilities of analysis of spatiotemporal FRAP data, which originate from multi-fractional diffusion, while striving to be widely applicable. This tool has the potential to elucidate the mechanisms of molecular transport and empower rational engineering of the drug release systems. The second part of the work focuses on the fabrication of such a spatiotemporarily-controlled drug release system employing the HA/PLL multilayer. This release system comprises different layers of various functionalities that together form a sandwich structure. The bottom layer, which serves as a reservoir, is formed by HA/PLL PEM deposited on a planar glass substrate. On top of the PEM, a layer of so-called hybrids is deposited. The hybrids consist of thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) -based hydrogel microparticles with surface-attached gold nanorods. The layer of hybrids is intended to serve as a gate that controls the local molecular transport through the PEM–solution-interface. The possibility of stimulating the molecular transport by near-infrared (NIR) laser irradiation is being explored. From several tested approaches for the deposition of hybrids onto the PEM surface, the drying-based approach was identified as optimal. Experiments, that examine the functionality of the fabricated sandwich at elevated temperature, document the reversible volume phase transition of the PEM-attached hybrids while sustaining the sandwich stability. Further, the gold nanorods were shown to effectively absorb light radiation in the tissue- and cell-friendly NIR spectral region while transducing the energy of light into heat. The rapid and reversible shrinkage of the PEM-attached hybrids was thereby achieved. Finally, dextran was employed as a model transport molecule. It loads into the PEM reservoir in a few seconds with the partition constant of 2.4, while it spontaneously releases in a slower, sustained manner. The local laser irradiation of the sandwich, which contains the fluorescein isothiocyanate tagged dextran, leads to a gradual reduction of fluorescence intensity in the irradiated region. The release system fabricated employs renowned photoresponsivity of the hybrids in an innovative setting. The results of the research are a step towards a spatially-controlled on-demand drug release system that paves the way to spatiotemporally controlled drug release. The approaches developed in this work have the potential to elucidate the molecular dynamics in ECM and to foster engineering of multilayers with properties tuned to mimic the ECM. The work aims at spatiotemporal control over the diffusion of bioactives and their presentation to the cells. N2 - Die Forschung an neuartigen und komplexen Biomaterialien ist unabdingbar für deren Einsatz in begehrten Bereichen wie der Gewebezüchtung, regenerativen Medizin, Zellkultivierung und Biotechnologie. Die hier vorgelegte Arbeit beschäftigt sich eingehend mit einem dieser vielversprechenden Materialien: Polyelektrolytische Multilayers (PEM), die aus Hyaluronsäure (Hyaluronic Acid, HA) und Poly-L-Lysin (PLL) zusammengesetzt sind. Diese gelartige Polymerbeschichtung ermöglicht es, (Bio-) Moleküle wie z.B. Proteine oder Medikamente zu akkumulieren und diese kontrolliert wieder abzugeben. Durch ihre Zusammensetzung und intrinsischen Merkmale können die PEM der Imitation einer Extrazellulären Matrix (ECM) dienen. Diese Eigenschaften machen die HA/PLL-PEM zu einem Anwärter auf verschiedene Bio-Anwendungen, wie den oben genannten. Die vorliegende Arbeit zielt auf die Entwicklung eines Ansatzes zur Einschätzung der multi-fraktionellen Diffusion in Multilayers (1. Teil), und auf die Kontrolle des lokalen molekularen Transports in und aus den Multilayers durch Laser-Stimulation (2. Teil). Der Aufnahme- und Freisetzungsmechanismus wird bestimmt von der Wechselwirkung zwischen Bioaktiva und den Bestandteilen der Multilayers, sowie allgemein vom Diffusionsprozess. Der Diffusion eines Molekül in HA/PLL-PEM weist unterschiedliche Diffusionsraten einzelner Molekülbestandteile auf. Derzeit existieren nur wenige Ansätze zur Einschätzung der Mobilität von Molekülen in derart komplexen Systemen. Diesem Mangel will die vorliegende Arbeit durch das Design eines neuartigen Evaluations-Instruments abhelfen. Dieses Instrument bedient sich eines simulationsbasierten Ansatzes zur Evaluation von Daten, die durch die fluorescence recovery after photobleaching (FRAP) -Methode erfasst wurden. Der Ansatz simuliert zunächst mögliche Szenarien der Fluoreszenz-Rückbildung, um diese anschließend mit Messdaten zu vergleichen; dazu werden Modell-Parameter angepasst, um suffiziente Vergleichswerte zu erzielen. Fluoreszierende Latex-Partikel verschiedener Größe und eine Fluoresceinlösung wurden als Kontroll- und Vergleichs-Proben verwendet, um die Ergebnisse zu überprüfen. Zusätzlich wurde die Diffusion des Proteins Cytochrom C in eine HA/PLL-PEM ausgewertet. Dieses Instrument weitet die Möglichkeiten der Analyse von spatiotemporären FRAP-Daten, die aus der multi-fraktionellen Diffusion stammen, erheblich und gleichzeitig ist es vielseitig einsetzbar. Das Instrument hat das Potential, die Mechanismen des Molekültransports weiter zu erhellen, und eine gezielte Steuerung der Freisetzung medikamentöser Wirkstoffe zu ermöglichen. Der zweite Teil der Arbeit widmet sich der Erstellung eines Systems zur spatiotemporären Wirkstofffreisetzung, das sich die HA/PLL-PEM zunutze macht. Dieses Freisetzungssystem umfasst verschiedene Lagen mit jeweils unterschiedlichen Funktionsweisen, die zusammen ein „Sandwich“ bilden. Die zugrundeliegende Schicht aus HA/PLL-PEM auf einem planaren Glassubstrat dient als Reservoir. Auf diese PEM ist eine Schicht sogenannter Hybride aufgebracht. Die Hybride bestehen aus thermoresponsiven Poly-N-Isopropylacrylamid (PNIPAM) -basierten Hydrogel-Mikropartikeln auf deren Gold-Nanostäbchen gebunden sind. Die Hybridschicht dient in der räumlichen Kontrolle des lokalen Molekültransports als „Schlupfloch“ an der Schnittstelle von PEM und Lösung. Die Möglichkeit der Stimulation des molekülaren Transports durch Bestrahlung mit einem Nah-Infrarot-Laser (NIR) wird hier untersucht. Von den mehreren getesteten Ansätzen zur Aufbringung von Hybriden auf die PEM-Oberfläche stellte sich die Trocknung als beste Möglichkeit heraus. Funktionalitätskontrollen des hergestellten Sandwiches bei erhöhter Temperatur ergaben eine reversible Volumenphasenübergang der PEM-gebundenen Hybride, wobei die Sandwich-Struktur erhalten blieb. Weiterhin wurde eine effektive Lichtabsorption durch die Gold-Nanostäbchen in den gewebe- und zellschonenden NIR-Spektrumsbereich gezeigt, wobei die aufgenommene Lichtenergie in Wärme umgewandelt wurde. Dadurch wurde eine schnelle und reversible Schrumpfung der PEM-gebundenen Hybride erreicht. Zuguterletzt wird Dextran als Modellmolekül für den Transport eingesetzt. Dieses wird in wenigen Sekunden – mit einem Verteilungskoeffizient von 2,4 – in das PEM-Reservoir aufgenommen, während es auf langsamere, anhaltende Weise freigesetzt wird. Die lokale Laser-Bestrahlung des Dextran-FITC-haltigen Sandwiches bewirkte eine schrittweise Reduktion der Fluoreszenz-Intensität in der bestrahlten Region. Das hier vorgestellte Molekül-Freisetzungssystem verwendet die vielzitierte Photoresponsivität von Hybriden auf neuartige Weise. Die Ergebnisse der Untersuchung bedeuten einen Fortschritt in Richtung eines räumlich kontrollierten, nach Bedarf steuerbaren Freisetzungs-Systems, das wiederum den Weg zu einer spatiotemporären Kontrollierbarkeit der Wirkstoff-Freisetzung bereiten könnte. Die in dieser Arbeit entwickelten Ansätze ermöglichen ein besseres Verständnis der Dynamik in der ECM, sowie die Entwicklung ECM-ähnlicher Multilayers. Die Arbeit hat die spatiotemporäre Kontrolle der Diffusion von bioaktiven Stoffen und deren Präsentation gegenüber Zellen zum Ziel. T2 - Molekulare Diffusion in Polyelektrolyt-Multischichten KW - polyelectrolyte multilayers KW - diffusion KW - simulation KW - FRAP KW - microgel KW - drug release KW - PNIPAM KW - IR laser KW - assessment of the diffusion KW - mulifractional diffusion KW - spatially and temporally controlled drug release KW - ordering of particles on the surface KW - close packing KW - dichteste Packung KW - Diffusion KW - Einschätzung der Diffusion KW - Wirkstoff-Freisetzun KW - Mikrogel KW - multi-fraktionelle Diffusion KW - Ordnung der Partikel auf der Oberfläche KW - Polyelektrolyt-Multischichten KW - Simulation KW - räumlich und zeitlich kontrollierte Wirkstoff-Freisetzung KW - FRAP KW - IR laser KW - PNIPAM Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-489038 ER - TY - THES A1 - Fischer, Jost Leonhardt T1 - Nichtlineare Kopplungsmechanismen akustischer Oszillatoren am Beispiel der Synchronisation von Orgelpfeifen T1 - Nonlinear coupling mechanisms of acoustical oscillators using the example of synchronization of organ pipes N2 - In dieser Arbeit werden nichtlineare Kopplungsmechanismen von akustischen Oszillatoren untersucht, die zu Synchronisation führen können. Aufbauend auf die Fragestellungen vorangegangener Arbeiten werden mit Hilfe theoretischer und experimenteller Studien sowie mit Hilfe numerischer Simulationen die Elemente der Tonentstehung in der Orgelpfeife und die Mechanismen der gegenseitigen Wechselwirkung von Orgelpfeifen identifiziert. Daraus wird erstmalig ein vollständig auf den aeroakustischen und fluiddynamischen Grundprinzipien basierendes nichtlinear gekoppeltes Modell selbst-erregter Oszillatoren für die Beschreibung des Verhaltens zweier wechselwirkender Orgelpfeifen entwickelt. Die durchgeführten Modellrechnungen werden mit den experimentellen Befunden verglichen. Es zeigt sich, dass die Tonentstehung und die Kopplungsmechanismen von Orgelpfeifen durch das entwickelte Oszillatormodell in weiten Teilen richtig beschrieben werden. Insbesondere kann damit die Ursache für den nichtlinearen Zusammenhang von Kopplungsstärke und Synchronisation des gekoppelten Zwei-Pfeifen Systems, welcher sich in einem nichtlinearen Verlauf der Arnoldzunge darstellt, geklärt werden. Mit den gewonnenen Erkenntnissen wird der Einfluss des Raumes auf die Tonentstehung bei Orgelpfeifen betrachtet. Dafür werden numerische Simulationen der Wechselwirkung einer Orgelpfeife mit verschiedenen Raumgeometrien, wie z. B. ebene, konvexe, konkave, und gezahnte Geometrien, exemplarisch untersucht. Auch der Einfluss von Schwellkästen auf die Tonentstehung und die Klangbildung der Orgelpfeife wird studiert. In weiteren, neuartigen Synchronisationsexperimenten mit identisch gestimmten Orgelpfeifen, sowie mit Mixturen wird die Synchronisation für verschiedene, horizontale und vertikale Pfeifenabstände in der Ebene der Schallabstrahlung, untersucht. Die dabei erstmalig beobachteten räumlich isotropen Unstetigkeiten im Schwingungsverhalten der gekoppelten Pfeifensysteme, deuten auf abstandsabhängige Wechsel zwischen gegen- und gleichphasigen Sychronisationsregimen hin. Abschließend wird die Möglichkeit dokumentiert, das Phänomen der Synchronisation zweier Orgelpfeifen durch numerische Simulationen, also der Behandlung der kompressiblen Navier-Stokes Gleichungen mit entsprechenden Rand- und Anfangsbedingungen, realitätsnah abzubilden. Auch dies stellt ein Novum dar. N2 - In this work non-linear coupling mechanisms in acoustic oscillator systems are examined which can lead to synchronization phenomena. This mechanisms are investigated in particular on organ pipes. Building up on the questions of preceding works the elements of the sound generation are identified using detailed experimental and theoretical studies, as well as numerical simulations. Furthermore the organ pipes interaction mechanisms of the mutual coupling are developed. This leads to a non-linear coupled oscillator model which is developed on the aeroacoustical and fluiddynamical first principles. The carried out model calculations are compared to the experimental results from preceding works. It appears that the sound generation and the coupling mechanisms are properly described by the developed nonlinear coupled model of self-sustained oscillators. In particular the cause can be cleared with it for the non-linear edges of the Arnold tongue of the coupled two-pipe system. With the new knowledge the influence of various space geometries on the sound generation of organ pipes is investigated. With numerical simulations the interaction of an organ pipe and different space geometries, like plane, convex, concave, and ridged geometry is studied. Also the influence of so called swell boxes on the sound generation and the sound pattern of the organ pipe is studied. In further new synchronization experiments with precisely equally tuned pairs of organ pipes, as well as with mixtures the synchronization is examined for various grids of horizontal and vertical pipe distances in the 2D-plane of sound radiation. The spatial discontinuities observed in the oscillation behaviour of the coupled pipe systems, point to changes between anti-phase and in-phase regimes of sychronization depending on pipes distances. Finally the possibility is documented to describe the phenomenon of the synchronization of two organ pipes realisticaly by solving the compressible Navier-Stokes equations numerically. KW - Synchronisation KW - Orgelpfeifen KW - Simulation KW - Experiment KW - Modell KW - synchronization KW - organ pipes KW - simulation KW - experiment KW - model Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-71975 ER -