TY - JOUR A1 - Zimmermann, Marc A1 - Stomps, Benjamin René Harald A1 - Schulte-Osseili, Christine A1 - Grigoriev, Dmitry A1 - Ewen, Dirk A1 - Morgan, Andrew A1 - Böker, Alexander T1 - Organic dye anchor peptide conjugates as an advanced coloring agent for polypropylene yarn JF - Textile Research Journal N2 - Polypropylene as one of the world's top commodity polymers is also widely used in the textile industry. However, its non-polar nature and partially crystalline structure significantly complicate the process of industrial coloring of polypropylene. Currently, textiles made of polypropylene or with a significant proportion of polypropylene are dyed under quite harsh conditions, including the use of high pressures and temperatures, which makes this process energy intensive. This research presents a three-step synthesis of coloring agents, capable of adhering onto synthetic polypropylene yarns without harsh energy-consuming conditions. This is possible by encapsulation of organic pigments using trimethoxyphenylsilane, introduction of surface double bonds via modification of the silica shell with trimethoxysilylpropylmethacrylate and final attachment of highly adhesive anchor peptides using thiol-ene chemistry. We demonstrate the applicability of this approach by dyeing polypropylene yarns in a simple process under ambient conditions after giving a step-by-step guide for the synthesis of these new dyeing agents. Finally, the successful dyeing of the yarns is visualized, and its practicability is discussed. KW - anchor peptides KW - organic dye pigments KW - coloring agents KW - polypropylene KW - yarns Y1 - 2020 U6 - https://doi.org/10.1177/0040517520932231 SN - 0040-5175 SN - 1746-7748 VL - 91 IS - 1-2 SP - 28 EP - 39 PB - Sage Publ. CY - London ER - TY - JOUR A1 - Doering, Ulrike A1 - Grigoriev, Dmitry A1 - Tapio, Kosti A1 - Bald, Ilko A1 - Böker, Alexander T1 - Synthesis of nanostructured protein-mineral-microcapsules by sonication JF - Soft matter N2 - We propose a simple and eco-friendly method for the formation of composite protein-mineral-microcapsules induced by ultrasound treatment. Protein- and nanoparticle-stabilized oil-in-water (O/W) emulsions loaded with different oils are prepared using high-intensity ultrasound. The formation of thin composite mineral proteinaceous shells is realized with various types of nanoparticles, which are pre-modified with Bovine Serum Albumin (BSA) and subsequently characterized by EDX, TGA, zeta potential measurements and Raman spectroscopy. Cryo-SEM and EDX mapping visualizations show the homogeneous distribution of the densely packed nanoparticles in the capsule shell. In contrast to the results reported in our previous paper,(1) the shell of those nanostructured composite microcapsules is not cross-linked by the intermolecular disulfide bonds between BSA molecules. Instead, a Pickering-Emulsion formation takes place because of the amphiphilicity-driven spontaneous attachment of the BSA-modified nanoparticles at the oil/water interface. Using colloidal particles for the formation of the shell of the microcapsules, in our case silica, hydroxyapatite and calcium carbonate nanoparticles, is promising for the creation of new functional materials. The nanoparticulate building blocks of the composite shell with different chemical, physical or morphological properties can contribute to additional, sometimes even multiple, features of the resulting capsules. Microcapsules with shells of densely packed nanoparticles could find interesting applications in pharmaceutical science, cosmetics or in food technology. Y1 - 2022 U6 - https://doi.org/10.1039/d1sm01638e SN - 1744-6848 VL - 18 IS - 13 SP - 2558 EP - 2568 PB - Royal Society of Chemistry CY - London ER - TY - JOUR A1 - Qiu, Liang A1 - Zhang, Haoran A1 - Bick, Thomas A1 - Martin, Johannes A1 - Wendler, Petra A1 - Böker, Alexander A1 - Glebe, Ulrich A1 - Xing, Chengfen T1 - Construction of highly ordered glyco-inside nano-assemblies through RAFT dispersion polymerization of galactose-decorated monomer JF - Angewandte Chemie : a journal of the Gesellschaft Deutscher Chemiker ; International edition N2 - Glyco-assemblies derived from amphiphilic sugar-decorated block copolymers (ASBCs) have emerged prominently due to their wide application, for example, in biomedicine and as drug carriers. However, to efficiently construct these glyco-assemblies is still a challenge. Herein, we report an efficient technology for the synthesis of glyco-inside nano-assemblies by utilizing RAFT polymerization of a galactose-decorated methacrylate for polymerization-induced self-assembly (PISA). Using this approach, a series of highly ordered glyco-inside nano-assemblies containing intermediate morphologies were fabricated by adjusting the length of the hydrophobic glycoblock and the polymerization solids content. A specific morphology of complex vesicles was captured during the PISA process and the formation mechanism is explained by the morphology of its precursor and intermediate. Thus, this method establishes a powerful route to fabricate glyco-assemblies with tunable morphologies and variable sizes, which is significant to enable the large-scale fabrication and wide application of glyco-assemblies. KW - galactose-decorated monomer KW - glyco-inside nano-assemblies KW - morphology KW - evolution KW - PISA KW - RAFT dispersion polymerization Y1 - 2021 U6 - https://doi.org/10.1002/anie.202015692 SN - 1433-7851 SN - 1521-3773 VL - 60 IS - 20 SP - 11098 EP - 11103 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Akarsu, Pinar A1 - Grobe, Richard A1 - Nowaczyk, Julius A1 - Hartlieb, Matthias A1 - Reinicke, Stefan A1 - Böker, Alexander A1 - Sperling, Marcel A1 - Reifarth, Martin T1 - Solid-phase microcontact printing for precise patterning of rough surfaces BT - using polymer-tethered elastomeric stamps for the transfer of reactive silanes JF - ACS applied polymer materials N2 - We present a microcontact printing (mu CP) routine suitable to introduce defined (sub-) microscale patterns on surface substrates exhibiting a high capillary activity and receptive to a silane-based chemistry. This is achieved by transferring functional trivalent alkoxysilanes, such as (3-aminopropyl)-triethoxysilane (APTES) as a low-molecular weight ink via reversible covalent attachment to polymer brushes grafted from elastomeric polydimethylsiloxane (PDMS) stamps. The brushes consist of poly{N-[tris(hydroxymethyl)-methyl]acrylamide} (PTrisAAm) synthesized by reversible addition-fragmentation chain-transfer (RAFT)-polymerization and used for immobilization of the alkoxysilane-based ink by substituting the alkoxy moieties with polymer-bound hydroxyl groups. Upon physical contact of the silane-carrying polymers with surfaces, the conjugated silane transfers to the substrate, thus completely suppressing ink-flow and, in turn, maximizing printing accuracy even for otherwise not addressable substrate topographies. We provide a concisely conducted investigation on polymer brush formation using atomic force microscopy (AFM) and ellipsometry as well as ink immobilization utilizing two-dimensional proton nuclear Overhauser enhancement spectroscopy (H-1-H-1-NOESY-NMR). We analyze the mu CP process by printing onto Si-wafers and show how even distinctively rough surfaces can be addressed, which otherwise represent particularly challenging substrates. KW - microcontact printing KW - capillary-active substrates KW - silane chemistry KW - PDMS surface grafting KW - surface patterning KW - shuttled RAFT-polymerization Y1 - 2021 U6 - https://doi.org/10.1021/acsapm.1c00024 SN - 2637-6105 VL - 3 IS - 5 SP - 2420 EP - 2431 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Reifarth, Martin A1 - Bekir, Marek A1 - Bapolisi, Alain M. A1 - Titov, Evgenii A1 - Nusshardt, Fabian A1 - Nowaczyk, Julius A1 - Grigoriev, Dmitry A1 - Sharma, Anjali A1 - Saalfrank, Peter A1 - Santer, Svetlana A1 - Hartlieb, Matthias A1 - Böker, Alexander T1 - A dual pH- and light-responsive spiropyrane-based surfactant BT - investigations on Its switching behavior and remote control over emulsion stability JF - Angewandte Chemie : a journal of the Gesellschaft Deutscher Chemiker ; International edition N2 - A cationic surfactant containing a spiropyrane unit is prepared exhibiting a dual-responsive adjustability of its surface-active characteristics. The switching mechanism of the system relies on the reversible conversion of the non-ionic spiropyrane (SP) to a zwitterionic merocyanine (MC) and can be controlled by adjusting the pH value and via light, resulting in a pH-dependent photoactivity: While the compound possesses a pronounced difference in surface activity between both forms under acidic conditions, this behavior is suppressed at a neutral pH level. The underlying switching processes are investigated in detail, and a thermodynamic explanation based on a combination of theoretical and experimental results is provided. This complex stimuli-responsive behavior enables remote-control of colloidal systems. To demonstrate its applicability, the surfactant is utilized for the pH-dependent manipulation of oil-in-water emulsions. KW - Dual-Responsiveness KW - Manipulation of Emulsion Stability KW - Spiropyrane KW - Surfactant KW - Switchable Surfactants KW - pH-Dependent Photoresponsivity Y1 - 2022 U6 - https://doi.org/10.1002/anie.202114687 SN - 1433-7851 SN - 1521-3773 VL - 61 IS - 21 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Doering, Ulrike A1 - Grigoriev, Dmitry A1 - Tapio, Kosti A1 - Rosencrantz, Sophia A1 - Rosencrantz, Ruben R. A1 - Bald, Ilko A1 - Böker, Alexander T1 - About the mechanism of ultrasonically induced protein capsule formation JF - RSC Advances : an international journal to further the chemical sciences / Royal Society of Chemistry N2 - In this paper, we propose a consistent mechanism of protein microcapsule formation upon ultrasound treatment. Aqueous suspensions of bovine serum albumin (BSA) microcapsules filled with toluene are prepared by use of high-intensity ultrasound following a reported method. Stabilization of the oil-in-water emulsion by the adsorption of the protein molecules at the interface of the emulsion droplets is accompanied by the creation of the cross-linked capsule shell due to formation of intermolecular disulfide bonds caused by highly reactive species like superoxide radicals generated sonochemically. The evidence for this mechanism, which until now remained elusive and was not proven properly, is presented based on experimental data from SDS-PAGE, Raman spectroscopy and dynamic light scattering. Y1 - 2021 U6 - https://doi.org/10.1039/d0ra08100k SN - 2046-2069 VL - 11 IS - 27 SP - 16152 EP - 16157 PB - RSC Publishing CY - London ER - TY - JOUR A1 - Mehr, Fatemeh Naderi A1 - Grigoriev, Dmitry A1 - Heaton, Rebecca A1 - Baptiste, Joshua A1 - Stace, Anthony J. A1 - Puretskiy, Nikolay A1 - Besley, Elena A1 - Böker, Alexander T1 - Self-assembly behavior of oppositely charged inverse bipatchy microcolloids JF - Small : nano micro N2 - A directed attractive interaction between predefined "patchy" sites on the surfaces of anisotropic microcolloids can provide them with the ability to self-assemble in a controlled manner to build target structures of increased complexity. An important step toward the controlled formation of a desired superstructure is to identify reversible electrostatic interactions between patches which allow them to align with one another. The formation of bipatchy particles with two oppositely charged patches fabricated using sandwich microcontact printing is reported. These particles spontaneously self-aggregate in solution, where a diversity of short and long chains of bipatchy particles with different shapes, such as branched, bent, and linear, are formed. Calculations show that chain formation is driven by a combination of attractive electrostatic interactions between oppositely charged patches and the charge-induced polarization of interacting particles. KW - electrostatic interactions KW - patchy particles KW - polyelectrolyte inks KW - sandwich microcontact printing KW - self-assembly Y1 - 2020 U6 - https://doi.org/10.1002/smll.202000442 SN - 1613-6810 SN - 1613-6829 VL - 16 IS - 14 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Wang, Xuepu A1 - Sperling, Marcel A1 - Reifarth, Martin A1 - Böker, Alexander T1 - Shaping metallic nanolattices BT - Design by microcontact printing from wrinkled stamps JF - Small N2 - A method for the fabrication of well-defined metallic nanostructures is presented here in a simple and straightforward fashion. As an alternative to lithographic techniques, this routine employs microcontact printing utilizing wrinkled stamps, which are prepared from polydimethylsiloxane (PDMS), and includes the formation of hydrophobic stripe patterns on a substrate via the transfer of oligomeric PDMS. Subsequent backfilling of the interspaces between these stripes with a hydroxyl-functional poly(2-vinyl pyridine) then provides the basic pattern for the deposition of citrate-stabilized gold nanoparticles promoted by electrostatic interaction. The resulting metallic nanostripes can be further customized by peeling off particles in a second microcontact printing step, which employs poly(ethylene imine) surface-decorated wrinkled stamps, to form nanolattices. Due to the independent adjustability of the period dimensions of the wrinkled stamps and stamp orientation with respect to the substrate, particle arrays on the (sub)micro-scale with various kinds of geometries are accessible in a straightforward fashion. This work provides an alternative, cost-effective, and scalable surface-patterning technique to fabricate nanolattice structures applicable to multiple types of functional nanoparticles. Being a top-down method, this process could be readily implemented into, e.g., the fabrication of optical and sensing devices on a large scale. KW - gold nanoparticle assembly KW - hydroxyl-functional poly(2-vinyl pyridine) KW - metallic nanolattices KW - microcontact printing KW - oligomeric KW - polydimethylsiloxane KW - polydimethylsiloxane wrinkles KW - wrinkled stamps Y1 - 2020 U6 - https://doi.org/10.1002/smll.201906721 SN - 1613-6810 SN - 1613-6829 VL - 16 IS - 11 SP - 1 EP - 8 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Garakani, Tayebeh Mirzaei A1 - Richter, Marina Juliane A1 - Böker, Alexander T1 - Controlling the bio-inspired synthesis of silica JF - Journal of colloid and interface science N2 - The influence of different parameters on the silicification procedure using lysozyme is reported. When polyethoxysiloxane (PEOS), an internally crosslinked silica reservoir, is used, regular structures with a narrow size distribution could be obtained only via introducing the silica precursor in two steps including initial dropping and subsequent addition of residual oil phase in one portion. We found that mixing sequence of mineralizing agents in the presence of a positively charged surfactant plays a key role in terms of silica precipitation when tetraethoxyorthosilicate (TEOS) is the oil phase. In contrast, well mineralized crumpled features with high specific surface area could be synthesized in the presence of PEOS as a silica precursor polymer, regardless of mixing sequence. Moreover, introducing sodium dodecyl sulfate (SDS) as a negatively charged surfactant resulted in regular silica sphere formation only in combination with hexylene glycol (MPD) as a specific co-solvent. Finally, it is demonstrated that by inclusion of different nanoparticles even more sophisticated hybrid materials can be generated. KW - Silicification KW - Lysozyme KW - Polyetlioxysiloxane KW - High specific surface area KW - Surfactant KW - Nanoparticles KW - Hybrid materials Y1 - 2016 U6 - https://doi.org/10.1016/j.jcis.2016.10.069 SN - 0021-9797 SN - 1095-7103 VL - 488 SP - 322 EP - 334 PB - Elsevier CY - San Diego ER - TY - JOUR A1 - Liebeck, Bernd Michael A1 - Hidalgo, Natalia A1 - Roth, Georg A1 - Popescu, Crisan A1 - Böker, Alexander T1 - Synthesis and characterization of Methyl Cellulose/Keratin Hydrolysate Composite Membranes JF - Polymers / Molecular Diversity Preservation International N2 - It is known that aqueous keratin hydrolysate solutions can be produced from feathers using superheated water as solvent. This method is optimized in this study by varying the time and temperature of the heat treatment in order to obtain a high solute content in the solution. With the dissolved polypeptides, films are produced using methyl cellulose as supporting material. Thereby, novel composite membranes are produced from bio-waste. It is expected that these materials exhibit both protein and polysaccharide properties. The influence of the embedded keratin hydrolysates on the methyl cellulose structure is investigated using Fourier transform infrared spectroscopy (FTIR) and wide angle X-ray diffraction (WAXD). Adsorption peaks of both components are present in the spectra of the membranes, while the X-ray analysis shows that the polypeptides are incorporated into the semi-crystalline methyl cellulose structure. This behavior significantly influences the mechanical properties of the composite films as is shown by tensile tests. Since further processing steps, e.g., crosslinking, may involve a heat treatment, thermogravimetric analysis (TGA) is applied to obtain information on the thermal stability of the composite materials. KW - bio-based KW - composite materials KW - methyl cellulose KW - keratin KW - superheated water Y1 - 2017 U6 - https://doi.org/10.3390/polym9030091 SN - 2073-4360 VL - 9 PB - MDPI CY - Basel ER -