@article{SerranoMunozFritschMishurovaetal.2020, author = {Serrano-Munoz, Itziar and Fritsch, Tobias and Mishurova, Tatiana and Trofimov, Anton and Apel, Daniel and Ulbricht, Alexander and Kromm, Arne and Hesse, Rene and Evans, Alexander and Bruno, Giovanni}, title = {On the interplay of microstructure and residual stress in LPBF IN718}, series = {Journal of materials science}, volume = {56}, journal = {Journal of materials science}, number = {9}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-020-05553-y}, pages = {5845 -- 5867}, year = {2020}, abstract = {The relationship between residual stresses and microstructure associated with a laser powder bed fusion (LPBF) IN718 alloy has been investigated on specimens produced with three different scanning strategies (unidirectional Y-scan, 90 degrees XY-scan, and 67 degrees Rot-scan). Synchrotron X-ray energy-dispersive diffraction (EDXRD) combined with optical profilometry was used to study residual stress (RS) distribution and distortion upon removal of the specimens from the baseplate. The microstructural characterization of both the bulk and the near-surface regions was conducted using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). On the top surfaces of the specimens, the highest RS values are observed in the Y-scan specimen and the lowest in the Rot-scan specimen, while the tendency is inversed on the side lateral surfaces. A considerable amount of RS remains in the specimens after their removal from the baseplate, especially in the Y- and Z-direction (short specimen dimension and building direction (BD), respectively). The distortion measured on the top surface following baseplate thinning and subsequent removal is mainly attributed to the amount of RS released in the build direction. Importantly, it is observed that the additive manufacturing microstructures challenge the use of classic theoretical models for the calculation of diffraction elastic constants (DEC) required for diffraction-based RS analysis. It is found that when the Reuss model is used for the calculation of RS for different crystal planes, as opposed to the conventionally used Kroner model, the results exhibit lower scatter. This is discussed in context of experimental measurements of DEC available in the literature for conventional and additively manufactured Ni-base alloys.}, language = {en} } @article{NadammalMishurovaFritschetal.2021, author = {Nadammal, Naresh and Mishurova, Tatiana and Fritsch, Tobias and Serrano-Munoz, Itziar and Kromm, Arne and Haberland, Christoph and Portella, Pedro Dolabella and Bruno, Giovanni}, title = {Critical role of scan strategies on the development of microstructure, texture, and residual stresses during laser powder bed fusion additive manufacturing}, series = {Additive manufacturing}, volume = {38}, journal = {Additive manufacturing}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2214-8604}, doi = {10.1016/j.addma.2020.101792}, pages = {13}, year = {2021}, abstract = {Laser based powder bed fusion additive manufacturing offers the flexibility to incorporate standard and user-defined scan strategies in a layer or in between the layers for the customized fabrication of metallic components. In the present study, four different scan strategies and their impact on the development of microstructure, texture, and residual stresses in laser powder bed fusion additive manufacturing of a nickel-based superalloy Inconel 718 was investigated. Light microscopy, scanning electron microscopy combined with electron back-scatter diffraction, and neutron diffraction were used as the characterization tools. Strong textures with epitaxially grown columnar grains were observed along the build direction for the two individual scan strategies. Patterns depicting the respective scan strategies were visible in the build plane, which dictated the microstructure development in the other planes. An alternating strategy combining the individual strategies in the successive layers and a 67 degrees rotational strategy weakened the texture by forming finer micro-structural features. Von Mises equivalent stress plots revealed lower stress values and gradients, which translates as lower distortions for the alternating and rotational strategies. Overall results confirmed the scope for manipulating the microstructure, texture, and residual stresses during laser powder bed fusion additive manufacturing by effectively controlling the scan strategies.}, language = {en} } @article{SchroederEvansPolatidisetal.2022, author = {Schr{\"o}der, Jakob and Evans, Alexander and Polatidis, Efthymios and Mohr, Gunther and Serrano-Munoz, Itziar and Bruno, Giovanni and Čapek, Jan}, title = {Understanding the impact of texture on the micromechanical anisotropy of laser powder bed fused Inconel 718}, series = {Journal of materials science}, volume = {57}, journal = {Journal of materials science}, number = {31}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-022-07499-9}, pages = {15036 -- 15058}, year = {2022}, abstract = {The manufacturability of metallic alloys using laser-based additive manufacturing methods such as laser powder bed fusion has substantially improved within the last decade. However, local melting and solidification cause hierarchically structured and crystallographically textured microstructures possessing large residual stress. Such microstructures are not only the origin of mechanical anisotropy but also pose metrological challenges for the diffraction-based residual stress determination. Here we demonstrate the influence of the build orientation and the texture on the microstructure and consequently the mechanical anisotropy of as-built Inconel 718. For this purpose, we manufactured specimens with [001]/[011]-, [001]- and [011]/[11 (1) over bar]-type textures along their loading direction. In addition to changes in the Young's moduli, the differences in the crystallographic textures result in variations of the yield and ultimate tensile strengths. With this in mind, we studied the anisotropy on the micromechanical scale by subjecting the specimens to tensile loads along the different texture directions during in situ neutron diffraction experiments. In this context, the response of multiple lattice planes up to a tensile strain of 10\% displayed differences in the load partitioning and the residual strain accumulation for the specimen with [011]/[(1) over bar 11]-type texture. However, the relative behavior of the specimens possessing an [001] /[011]- and [001]-type texture remained qualitatively similar. The consequences on the metrology of residual stress determination methods are discussed.}, language = {en} } @article{UlbrichtMohrAltenburgetal.2021, author = {Ulbricht, Alexander and Mohr, Gunther and Altenburg, Simon J. and Oster, Simon and Maierhofer, Christiane and Bruno, Giovanni}, title = {Can potential defects in LPBF be healed from the laser exposure of subsequent layers?}, series = {Metals : open access journal}, volume = {11}, journal = {Metals : open access journal}, number = {7}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met11071012}, pages = {14}, year = {2021}, abstract = {Additive manufacturing (AM) of metals and in particular laser powder bed fusion (LPBF) enables a degree of freedom in design unparalleled by conventional subtractive methods. To ensure that the designed precision is matched by the produced LPBF parts, a full understanding of the interaction between the laser and the feedstock powder is needed. It has been shown that the laser also melts subjacent layers of material underneath. This effect plays a key role when designing small cavities or overhanging structures, because, in these cases, the material underneath is feed-stock powder. In this study, we quantify the extension of the melt pool during laser illumination of powder layers and the defect spatial distribution in a cylindrical specimen. During the LPBF process, several layers were intentionally not exposed to the laser beam at various locations, while the build process was monitored by thermography and optical tomography. The cylinder was finally scanned by X-ray computed tomography (XCT). To correlate the positions of the unmolten layers in the part, a staircase was manufactured around the cylinder for easier registration. The results show that healing among layers occurs if a scan strategy is applied, where the orientation of the hatches is changed for each subsequent layer. They also show that small pores and surface roughness of solidified material below a thick layer of unmolten material (>200 mu m) serve as seeding points for larger voids. The orientation of the first two layers fully exposed after a thick layer of unmolten powder shapes the orientation of these voids, created by a lack of fusion.}, language = {en} } @article{SchroederEvansMishurovaetal.2021, author = {Schr{\"o}der, Jakob and Evans, Alexander and Mishurova, Tatiana and Ulbricht, Alexander and Sprengel, Maximilian and Serrano-Munoz, Itziar and Fritsch, Tobias and Kromm, Arne and Kannengießer, Thomas and Bruno, Giovanni}, title = {Diffraction-based residual stress characterization in laser additive manufacturing of metals}, series = {Metals : open access journal}, volume = {11}, journal = {Metals : open access journal}, number = {11}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met11111830}, pages = {34}, year = {2021}, abstract = {Laser-based additive manufacturing methods allow the production of complex metal structures within a single manufacturing step. However, the localized heat input and the layer-wise manufacturing manner give rise to large thermal gradients. Therefore, large internal stress (IS) during the process (and consequently residual stress (RS) at the end of production) is generated within the parts. This IS or RS can either lead to distortion or cracking during fabrication or in-service part failure, respectively. With this in view, the knowledge on the magnitude and spatial distribution of RS is important to develop strategies for its mitigation. Specifically, diffraction-based methods allow the spatial resolved determination of RS in a non-destructive fashion. In this review, common diffraction-based methods to determine RS in laser-based additive manufactured parts are presented. In fact, the unique microstructures and textures associated to laser-based additive manufacturing processes pose metrological challenges. Based on the literature review, it is recommended to (a) use mechanically relaxed samples measured in several orientations as appropriate strain-free lattice spacing, instead of powder, (b) consider that an appropriate grain-interaction model to calculate diffraction-elastic constants is both material- and texture-dependent and may differ from the conventionally manufactured variant. Further metrological challenges are critically reviewed and future demands in this research field are discussed.}, language = {en} } @article{ManiKupschMuelleretal.2022, author = {Mani, Deepak and Kupsch, Andreas and M{\"u}ller, Bernd R. and Bruno, Giovanni}, title = {Diffraction Enhanced Imaging Analysis with Pseudo-Voigt Fit Function}, series = {Journal of imaging : open access journal}, volume = {8}, journal = {Journal of imaging : open access journal}, number = {8}, publisher = {MDPI}, address = {Basel}, issn = {2313-433X}, doi = {10.3390/jimaging8080206}, pages = {13}, year = {2022}, abstract = {Diffraction enhanced imaging (DEI) is an advanced digital radiographic imaging technique employing the refraction of X-rays to contrast internal interfaces. This study aims to qualitatively and quantitatively evaluate images acquired using this technique and to assess how different fitting functions to the typical rocking curves (RCs) influence the quality of the images. RCs are obtained for every image pixel. This allows the separate determination of the absorption and the refraction properties of the material in a position-sensitive manner. Comparison of various types of fitting functions reveals that the Pseudo-Voigt (PsdV) function is best suited to fit typical RCs. A robust algorithm was developed in the Python programming language, which reliably extracts the physically meaningful information from each pixel of the image. We demonstrate the potential of the algorithm with two specimens: a silicone gel specimen that has well-defined interfaces, and an additively manufactured polycarbonate specimen.}, language = {en} } @article{MishurovaStegemannLyamkinetal.2022, author = {Mishurova, Tatiana and Stegemann, Robert and Lyamkin, Viktor and Cabeza, Sandra and Evsevleev, Sergei and Pelkner, Matthias and Bruno, Giovanni}, title = {Subsurface and bulk residual stress analysis of S235JRC+C Steel TIG weld by diffraction and magnetic stray field measurements}, series = {Experimental mechanics : an international journal of the Society for Experimental Mechanics}, volume = {62}, journal = {Experimental mechanics : an international journal of the Society for Experimental Mechanics}, number = {6}, publisher = {Springer}, address = {New York}, issn = {0014-4851}, doi = {10.1007/s11340-022-00841-x}, pages = {1017 -- 1025}, year = {2022}, abstract = {Background Due to physical coupling between mechanical stress and magnetization in ferromagnetic materials, it is assumed in the literature that the distribution of the magnetic stray field corresponds to the internal (residual) stress of the specimen. The correlation is, however, not trivial, since the magnetic stray field is also influenced by the microstructure and the geometry of component. The understanding of the correlation between residual stress and magnetic stray field could help to evaluate the integrity of welded components. Objective This study aims at understanding the possible correlation of subsurface and bulk residual stress with magnetic stray field in a low carbon steel weld. Methods The residual stress was determined by synchrotron X-ray diffraction (SXRD, subsurface region) and by neutron diffraction (ND, bulk region). SXRD possesses a higher spatial resolution than ND. Magnetic stray fields were mapped by utilizing high-spatial-resolution giant magneto resistance (GMR) sensors. Results The subsurface residual stress overall correlates better with the magnetic stray field distribution than the bulk stress. This correlation is especially visible in the regions outside the heat affected zone, where the influence of the microstructural features is less pronounced but steep residual stress gradients are present. Conclusions It was demonstrated that the localized stray field sources without any obvious microstructural variations are associated with steep stress gradients. The good correlation between subsurface residual stress and magnetic signal indicates that the source of the magnetic stray fields is to be found in the range of the penetration depth of the SXRD measurements.}, language = {en} }