@article{WangRychkovNguyenetal.2020, author = {Wang, Jingwen and Rychkov, Dmitry and Nguyen, Quyet Doan and Gerhard, Reimund}, title = {Unexpected bipolar space-charge polarization across transcrystalline interfaces in polypropylene electret films}, series = {Journal of applied physics}, volume = {128}, journal = {Journal of applied physics}, number = {13}, publisher = {American Institute of Physics, AIP}, address = {Melville, NY}, issn = {0021-8979}, doi = {10.1063/5.0022071}, pages = {7}, year = {2020}, abstract = {A double-layer transcrystalline polypropylene (PP) film with a flat central interface layer between its two transcrystalline layers is obtained by recrystallization from the melt between two polytetrafluoroethylene (PTFE) surfaces on both sides of the PP film. Its electret properties are studied and compared with those of a single-layer transcrystalline PP film re-crystallized in contact with only one PTFE surface. Within experimental uncertainty, the two types of transcrystalline films exhibit the same thermal properties and crystallinities. After thermal poling, however, two hetero-charge layers of opposite polarity are found on the internal interfaces of the double-layer transcrystalline films and may together be considered as micrometer-sized dipoles. The unexpected phenomenon does not occur in single-layer transcrystalline samples without a central interface layer, suggesting that the interfaces between the transcrystalline layers and the micrometer-thick central interface layer may be the origin of deeper traps rather than the crystalline structures in the transcrystallites or the spherulites. The origin of the interfacial charges was also studied by means of an injection-blocking charging method, which revealed that intrinsic charge carriers introduced during recrystallization are most likely responsible for the interfacial charges. It is fascinating that a material as familiar as PP can exhibit such intriguing properties with a special bipolar space-charge polarization across the central interface layer after quasi-epitaxial surface moulding into a double-layer transcrystalline form. In addition to applications in electret (micro-)devices for electro-mechanical transduction, the highly ordered structures may also be employed as a new paradigm for studying charge storage and transport in polymer electrets and in dielectrics for DC electrical insulation.}, language = {en} } @article{RamanVenkatesanSmykallaPlossetal.2022, author = {Raman Venkatesan, Thulasinath and Smykalla, David and Ploss, Bernd and W{\"u}bbenhorst, Michael and Gerhard, Reimund}, title = {Tuning the relaxor-ferroelectric properties of Poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) Terpolymer films by means of thermally induced micro- and nanostructures}, series = {Macromolecules : a publication of the American Chemical Society}, volume = {55}, journal = {Macromolecules : a publication of the American Chemical Society}, number = {13}, publisher = {American Chemical Society}, address = {Washington}, issn = {0024-9297}, doi = {10.1021/acs.macromol.2c00302}, pages = {5621 -- 5635}, year = {2022}, abstract = {The effects of thermal processing on the micro- and nanostructural features and thus also on the relaxor-ferroelectric properties of a P(VDF-TrFE-CFE) terpolymer were investigated in detail by means of dielectric experiments, such as dielectric relaxation spectroscopy (DRS), dielectric hysteresis loops, and thermally stimulated depolarization currents (TSDCs). The results were correlated with those obtained from differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and Fourier-transform infrared spectroscopy (FTIR). The results from DRS and DSC show that annealing reduces the Curie transition temperature of the terpolymer, whereas the results from WAXD scans and FTIR spectra help to understand the shift in the Curie transition temperatures as a result of reducing the ferroelectric phase fraction, which by default exists even in terpolymers with relatively high CFE contents. In addition, the TSDC traces reveal that annealing has a similar effect on the midtemperature transition by altering the fraction of constrained amorphous phase at the interphase between the crystalline and the amorphous regions. Changes in the transition temperatures are in turn related to the behavior of the hysteresis curves on differently heat-treated samples. During heating, evolution of the hysteresis curves from ferroelectric to relaxor-ferroelectric, first exhibiting single hysteresis loops and then double hysteresis loops near the Curie transition of the sample, is observed. When comparing the dielectric-hysteresis loops obtained at various temperatures, we find that annealed terpolymer films show higher electric-displacement values and lower coercive fields than the nonannealed sample, irrespective of the measurement temperature, and also exhibit ideal relaxor- ferroelectric behavior at ambient temperatures, which makes them excellent candidates for applications at or near room temperature. By tailoring the annealing conditions, it has been shown that the application temperature could be increased by fine tuning the induced micro- and nanostructures.}, language = {en} } @article{SpelzhausenIonianGerhardetal.2020, author = {Spelzhausen, Simon and Ionian, Mario-Rafael and Gerhard, Reimund and Plath, Ronald}, title = {Time-resolved measurement of space-charge evolution in dielectric films or slabs by means of repeatable laser-induced pressure pulses}, series = {Review of scientific instruments : a monthly journal devoted to scientific instruments, apparatus, and techniques}, volume = {91}, journal = {Review of scientific instruments : a monthly journal devoted to scientific instruments, apparatus, and techniques}, number = {5}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0034-6748}, doi = {10.1063/1.5142443}, pages = {7}, year = {2020}, abstract = {A new variant of the Laser-Induced Pressure-Pulse (LIPP) method for repeatable, time-resolved space-charge profile measurements is proposed and demonstrated. Automated deposition of a fresh laser-target film before each illumination leads to good repeatability of the LIPP and thus allows for the detection of time-resolved changes in the space-charge distribution over many hours. We describe and discuss the experimental setup and its features, compare the repeatability of the LIPP measurements on the same sample without and with re-preparation of the test cell, and present the time-resolved evolution of the space-charge profile in a two-layer arrangement of a silicone-grease and a silicone-elastomer film as an example. Finally, the temperature dependence of the space-charge evolution during polarization under high voltage and during depolarization in short circuit is shown. Possible uses and future developments of the new LIPP approach are also discussed.}, language = {en} } @article{FloresSuarezMellingerWegeneretal.2006, author = {Flores Su{\´a}rez, Rosaura and Mellinger, Axel and Wegener, Michael and Wirges, Werner and Gerhard, Reimund and Singh, Rajeev}, title = {Thermal-pulse tomography of polarization distributions in a cylindrical geometry}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {13}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {5}, publisher = {IEEE}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2006.258210}, pages = {1030 -- 1035}, year = {2006}, abstract = {Fast, three-dimensional polarization mapping in piezoelectric sensor cables was performed by means of the novel thermal-pulse tomography (TPT) technique with a lateral resolution of 200 mum. The active piezoelectric cable material (a copolymer of polyvinylidene fluoride with trifluoroethylene) was electrically poled with a point-to-cable corona discharge. A focused laser was employed to heat the opaque outer electrode, and the short-circuit current generated by the thermal pulse was used to obtain 3D polarization maps via the scale transformation method. The article describes the TPT technique as a fast non-destructive option for studying cylindrical geometries.}, language = {en} } @article{WangRychkovNguyenetal.2020, author = {Wang, Jingwen and Rychkov, Dmitry and Nguyen, Quyet Doan and Gerhard, Reimund}, title = {The influence of orthophosphoric-acid surface modification on charge-storage enhancement in polypropylene electrets}, series = {Journal of applied physics}, volume = {128}, journal = {Journal of applied physics}, number = {3}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/5.0013805}, pages = {6}, year = {2020}, abstract = {Bipolar electrets from polypropylene (PP) are essential, e.g., in electret air filters and in cellular-foam ferroelectrets. Therefore, the mechanism of surface-charge stability enhancement on PP electrets via orthophosphoric-acid surface treatment is investigated in detail. It is shown that the significant charge-stability enhancement can be mainly attributed to deeper surface traps originating from deposited chemicals and topographic features on the modified surfaces. Thermally stimulated discharge of chemically treated and non-treated PP films with different surface-charge densities is used to test the limits of the newly formed deep traps in terms of the capacity for hosting surface charges. When the initial surface-charge density is very high, more charges are forced into shallower original traps on the surface or in the bulk of the treated PP samples, reducing the effect of the deeper surface traps brought by the surface modification. The well-known crossover phenomenon (of the surface-charge decay curves) has been observed between modified PP electrets charged to +/- 2kV and to +/- 3kV. Acoustically probed charge distributions in the thickness direction of PP electrets at different stages of thermal discharging indicate that the deep surface trapping sites may have preference for negative charges, resulting in the observed asymmetric charge stability of the modified PP films.}, language = {en} } @article{GidionGerhard2018, author = {Gidion, Gunnar and Gerhard, Reimund}, title = {The Bow on a String}, series = {Acta Acustica united with Acustica}, volume = {104}, journal = {Acta Acustica united with Acustica}, number = {2}, publisher = {Hirzel Verlag}, address = {Stuttgart}, issn = {1610-1928}, doi = {10.3813/AAA.919174}, pages = {315 -- 322}, year = {2018}, abstract = {The interaction between a bowed string instrument and its player is conveyed by the bow, the vibrational properties of which can be measured either separately on the bow or during the bowing procedure. Here, two piezoelectric film sensors, made of a ferroelectret material, are installed on a violin bow, one sensor at the tip and one at the frog. With these sensors, a violin is played under normal conditions, and the signals are analysed. The features in the resulting spectrograms are identified as string harmonics and longitudinal bow-hair resonances. The bow-hair sections on both sides of the bow-string contact exhibit separate resonances which are observed as absorption dips in the spectra. Owing to the sensor positions at the bow-hair terminations, it can be inferred that the two bow-hair sections act as mutual vibration absorbers. From a regression of the observed resonances, the longitudinal bow-hair velocity can be obtained. With additional film sensors under the violin bridge, body vibrations were also detected providing further details of the coupling mechanisms.}, language = {en} } @article{WangZhangYanetal.2022, author = {Wang, Feipeng and Zhang, Zheng and Yan, Yuyang and Shen, Zijia and Wang, Qiang and Gerhard, Reimund}, title = {Surface reconstruction on electro-spun PVA/PVP nanofibers by water evaporation}, series = {Nanomaterials}, volume = {12}, journal = {Nanomaterials}, number = {5}, publisher = {MDPI}, address = {Basel}, issn = {2079-4991}, doi = {10.3390/nano12050797}, pages = {7}, year = {2022}, abstract = {Tailoring the secondary surface morphology of electro-spun nanofibers has been highly desired, as such delicate structures equip nanofibers with distinct functions. Here, we report a simple strategy to directly reconstruct the surface of polyvinyl alcohol/polyvinylpyrrolidone (PVA/PVP) nanofibers by water evaporation. The roughness and diameter of the nanofibers depend on the temperature during vacuum drying. Surface changes of the nanofibers from smooth to rough were observed at 55 degrees C, with a significant drop in nanofiber diameter. We attribute the formation of the secondary surface morphology to the intermolecular forces in the water vapor, including capillary and the compression forces, on the basis of the results from the Fourier-transform infrared (FTIR) and X-ray photoelectron (XPS) spectroscopy. The strategy is universally effective for various electro-spun polymer nanofibers, thus opening up avenues toward more detailed and sophisticated structure design and implementation for nanofibers.}, language = {en} } @article{RamanVenkatesanWuebbenhorstGerhard2022, author = {Raman Venkatesan, Thulasinath and W{\"u}bbenhorst, Michael and Gerhard, Reimund}, title = {Structure-property relationships in three-phase relaxor-ferroelectric terpolymers}, series = {Ferroelectrics}, volume = {586}, journal = {Ferroelectrics}, number = {1}, publisher = {Routledge, Taylor \& Francis Group}, address = {Abingdon}, issn = {0015-0193}, doi = {10.1080/00150193.2021.2014260}, pages = {60 -- 81}, year = {2022}, abstract = {Poly(vinylidenefluoride-trifluoroethylene)-based (P(VDF-TrFE)-based) terpolymers represent a new class of electroactive polymer materials that are relaxor-ferroelectric (RF) polymers and that offer unique and attractive property combinations in comparison with conventional ferroelectric polymers. The RF state is achieved by introducing a fluorine-containing termonomer as a "defect" into the ferroelectric P(VDF-TrFE) copolymer, which reduces the interaction between the VDF/TrFE dipoles. The resulting terpolymer exhibits a low Curie transition temperature and small remanent and coercive fields yielding a slim hysteresis loop that is typical for RF materials. Though the macroscopic behavior is similar to RF ceramics, the mechanisms of relaxor ferroelectricity in semi-crystalline polymers are different and not fully understood yet. Structure-property relationships play an important role in RF terpolymers, as they govern the final RF properties. Hence, a review of important characteristics, previous studies and relevant developments of P(VDF-TrFE)-based terfluoropolymers with either chlorofluoroethylene (CFE) or chlorotrifluoroethylene (CTFE) as the termonomer is deemed useful. The role of the termonomer and of its composition, as well as the effects of the processing conditions on the semi-crystalline structure which in turn affects the final RF properties are discussed in detail. In addition, the presence of noteworthy transition(s) in the mid-temperature range and the influence of preparation conditions on those transitions are reviewed. A better understanding of the fundamental aspects affecting the semi-crystalline structures will help to elucidate the nature of RF activity in VDF-based terpolymers and also help to further improve their applications-relevant electroactive properties.}, language = {en} } @misc{LouposDamigosAmditisetal.2017, author = {Loupos, Konstantinos and Damigos, Yannis and Amditis, Angelos and Gerhard, Reimund and Rychkov, Dmitry and Wirges, Werner and Schulze, Manuel and Lenas, Sotiris-Angelos and Chatziandreoglou, Christos and Malliou, Christina and Tsaoussidis, Vassilis and Brady, Ken and Frankenstein, Bernd}, title = {Structural health monitoring system for bridges based on skin-like sensor}, series = {IOP conference series : Materials science and engineering}, volume = {236}, journal = {IOP conference series : Materials science and engineering}, publisher = {IOP Publ. Ltd.}, address = {Bristol}, issn = {1757-8981}, doi = {10.1088/1757-899X/236/1/012100}, pages = {10}, year = {2017}, abstract = {Structural health monitoring activities are of primal importance for managing transport infrastructure, however most SHM methodologies are based on point-based sensors that have limitations in terms of their spatial positioning requirements, cost of development and measurement range. This paper describes the progress on the SENSKIN EC project whose objective is to develop a dielectric-elastomer and micro-electronics-based sensor, formed from a large highly extensible capacitance sensing membrane supported by advanced microelectronic circuitry, for monitoring transport infrastructure bridges. Such a sensor could provide spatial measurements of strain in excess of 10\%. The actual sensor along with the data acquisition module, the communication module and power electronics are all integrated into a compact unit, the SENSKIN device, which is energy-efficient, requires simple signal processing and it is easy to install over various surface types. In terms of communication, SENSKIN devices interact with each other to form the SENSKIN system; a fully distributed and autonomous wireless sensor network that is able to self-monitor. SENSKIN system utilizes Delay-/Disruption-Tolerant Networking technologies to ensure that the strain measurements will be received by the base station even under extreme conditions where normal communications are disrupted. This paper describes the architecture of the SENSKIN system and the development and testing of the first SENSKIN prototype sensor, the data acquisition system, and the communication system.}, language = {en} } @misc{CheilakouTsopelasAnastasopoulosetal.2018, author = {Cheilakou, E. and Tsopelas, N. and Anastasopoulos, A. and Kourousis, D. and Rychkov, Dmitry and Gerhard, Reimund and Frankenstein, B. and Amditis, A. and Damigos, Y. and Bouklas, C.}, title = {Strain monitoring system for steel and concrete structures}, series = {Procedia Structural Integrity}, volume = {10}, journal = {Procedia Structural Integrity}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2452-3216}, doi = {10.1016/j.prostr.2018.09.005}, pages = {25 -- 32}, year = {2018}, abstract = {The present work is part of a collaborative H2020 European funded research project called SENSKIN, that aims to improve Structural Health Monitoring (SHM) for transport infrastructure through the development of an innovative monitoring and management system for bridges based on a novel, inexpensive, skin-like sensor. The integrated SENSKIN technology will be implemented in the case of steel and concrete bridges, and tested, field-evaluated and benchmarked on actual bridge environment against a conventional health monitoring solution developed by Mistras Group Hellas. The main objective of the present work is to implement the autonomous, fully functional strain monitoring system based on commercially available off-the-shelf components, that will be used to accomplish direct comparison between the performance of the innovative SENSKIN sensors and the conventional strain sensors commonly used for structural monitoring of bridges. For this purpose, the mini Structural Monitoring System (mini SMS) of Physical Acoustics Corporation, a comprehensive data acquisition unit designed specifically for long-term unattended operation in outdoor environments, was selected. For the completion of the conventional system, appropriate foil-type strain sensors were selected, driven by special conditioners manufactured by Mistras Group. A comprehensive description of the strain monitoring system and its peripheral components is provided in this paper. For the evaluation of the integrated system's performance and the effect of various parameters on the long-term behavior of sensors, several test steel pieces instrumented with different strain sensors configurations were prepared and tested in both laboratory and field ambient conditions. Furthermore, loading tests were performed aiming to validate the response of the system in monitoring the strains developed in steel beam elements subject to bending regimes. Representative results obtained from the above experimental tests have been included in this paper as well.}, language = {en} } @article{WangRychkovGerhard2021, author = {Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Space-charge electret properties of polypropylene films with transcrystalline or spherulitic structures}, series = {Journal of applied physics : AIP's archival journal for significant new results in applied physics / publ. by the American Institute of Physics}, volume = {129}, journal = {Journal of applied physics : AIP's archival journal for significant new results in applied physics / publ. by the American Institute of Physics}, number = {6}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/5.0039867}, pages = {7}, year = {2021}, abstract = {Spherulite-related space-charge electret properties of polypropylene (PP) have been widely discussed in the past decades. In the present paper, a less-common crystalline structure in PP-transcrystalline PP-is studied regarding its electret behavior in comparison with the typical spherulitic morphology. Polarized light microscopy and differential scanning calorimetry were employed to characterize the crystallite types and crystallinities of transcrystalline and spherulitic PP. Their electret functionality is investigated by means of thermally stimulated discharge experiments, where the cross-over phenomenon is observed on transcrystalline PP films, whereas surface-potential saturation and undercharging on the surface occur on the spherulitic samples. Besides, an asymmetrical behavior of positive and negative surface-charge stabilities is found on PP with spherulites, the negatively charged spherulitic surfaces show a better charge stability. It is shown that PP electrets are very sensitive to changes in the microscopic crystalline structures and their interfaces as well as in the molecular conformations controlled through adjustments of the respective processing steps. In addition, surface and bulk nanocomposites of PP or low-density polyethylene with inorganic particles are included in the comparison. In view of recent developments in the areas of PP-based electret-fiber filters and cellular-foam ferroelectrets, the observed changes in the charge-storage properties may have particular relevance, as the required film, fiber, or foam processing might significantly modify crystalline morphologies and nano-scale interfaces in PP electrets. Limitations in the charge-storage capabilities of interface structures may also be of interest in the context of high-voltage electrical-insulation materials where reduced space-charge accumulation and slightly increased charge transport can be advantageous.}, language = {en} } @article{FruebingKremmerGerhardetal.2006, author = {Fr{\"u}bing, Peter and Kremmer, Alexander and Gerhard, Reimund and Spanoudaki, Anna and Pissis, Polycarpos}, title = {Relaxation processes at the glass transition in polyamide 11: From rigidity to viscoelasticity}, series = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, volume = {125}, journal = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, number = {12}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-9606}, doi = {10.1063/1.2360266}, pages = {8}, year = {2006}, abstract = {Relaxation processes associated with the glass transition in nonferroelectric and ferroelectric polyamide (PA) 11 are investigated by means of differential scanning calorimetry, dynamic mechanical analysis, and dielectric relaxation spectroscopy (DRS) in order to obtain information about the molecular mobility within the amorphous phase. In particular, the effects of melt quenching, cold drawing, and annealing just below the melting region are studied with respect to potential possibilities and limitations for improving the piezoelectric and pyroelectric properties of PA 11. A relaxation map is obtained from DRS that shows especially the crossover region where the cooperative alpha relaxation and the local beta relaxation merge into a single high-temperature process. No fundamental difference between quenched, cold-drawn, and annealed films is found, though in the cold-drawn (ferroelectric) film the alpha relaxation is suppressed and slowed down, but it is at least partly recovered by subsequent annealing. It is concluded that there exists an amorphous phase in all structures, even in the cold-drawn film. The amorphous phase can be more rigid or more viscoelastic depending on preparation. Cold drawing not only leads to crystallization in a ferroelectric form but also to higher rigidity of the remaining amorphous phase. Annealing just below the melting region after cold drawing causes a stronger phase separation between the crystalline phase and a more viscoelastic amorphous phase.}, language = {en} } @article{RamanVenkatesanGulyakovaFruebingetal.2018, author = {Raman Venkatesan, Thulasinath and Gulyakova, Anna A. and Fr{\"u}bing, Peter and Gerhard, Reimund}, title = {Relaxation processes and structural transitions in poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) relaxor-ferroelectric terpolymers as seen in dielectric spectroscopy}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {25}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {6}, publisher = {Institut of Electrical and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2018.007440}, pages = {2229 -- 2235}, year = {2018}, abstract = {Dielectric relaxation processes and structural transitions in Poly(vinylidenefluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer films with two different monomer compositions were investigated in comparison with Poly(vinylidenefluoride-trifluoroethylene) (P(VDF-TrFE)) copolymer films as reference material. Differential Scanning Calorimetry was employed to assess annealing effects on phase transitions and crystalline structure, while relaxation processes were investigated by means of Dielectric Relaxation Spectroscopy, the results of which indicate the existence of two separate dispersion regions, denoted as processes A and B, respectively. Process A appears at a certain temperature independent of frequency, but is strongly influenced by the crystallisation temperature and the CFE content, while peak B shows typical features of a relaxation process and is less influenced by crystallisation temperature and CFE content. Furthermore, peak B is related to the glass transition which is more pronounced in the terpolymer than in P(VDF-TrFE). A closer analysis indicates that the addition of CFE and thermal annealing gradually shift the ferro-to-paraelectric transition in P(VDF-TrFE) to lower temperatures, while the phase transition is transformed more and more into a relaxation.}, language = {en} } @article{GerhardKacprzyk2022, author = {Gerhard, Reimund and Kacprzyk, Ryszard}, title = {Paul B{\"o}ning - early electret researcher in Shanghai and Wroclaw (1922-1945)}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {29}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {3}, publisher = {Institute of Electrical and Electronics Engineers}, address = {New York, NY}, issn = {1070-9878}, doi = {10.1109/TDEI.2022.3168372}, pages = {853 -- 858}, year = {2022}, abstract = {The scientific career and the research activities of Paul Boening, especially during his tenures at Tongji University in Shanghai (Woosung Campus, 1922-1936) and the Technical University of Wroclaw (TH Breslau, 1936-1945), are briefly reviewed. In particular, Boening's pioneering investigations in the area of electrets and space charge in dielectrics are emphasized. We attempt to shed some light on the significant achievements of a virtually unknown contributor to the early history of electrets and of space-charge research and high-voltage engineering, during the 1920s and 1930s. It should be noted that dielectrics research was a truly international endeavor already at that time.}, language = {en} } @article{RamanVenkatesanSmykallaPlossetal.2021, author = {Raman Venkatesan, Thulasinath and Smykalla, David and Ploss, Bernd and W{\"u}bbenhorst, Michael and Gerhard, Reimund}, title = {Non-linear dielectric spectroscopy for detecting and evaluating structure-property relations in a P(VDF-TrFE-CFE) relaxor-ferroelectric terpolymer}, series = {Applied physics : A, Materials science \& processing}, volume = {127}, journal = {Applied physics : A, Materials science \& processing}, number = {10}, publisher = {Springer}, address = {Berlin ; Heidelberg ; New York}, issn = {0947-8396}, doi = {10.1007/s00339-021-04876-0}, pages = {10}, year = {2021}, abstract = {Non-linear dielectric spectroscopy (NLDS) is employed as an effective tool to study relaxation processes and phase transitions of a poly(vinylidenefluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) relaxor-ferroelectric (R-F) terpolymer in detail. Measurements of the non-linear dielectric permittivity epsilon 2 ' reveal peaks at 30 and 80 degrees C that cannot be identified in conventional dielectric spectroscopy. By combining the results from NLDS experiments with those from other techniques such as thermally stimulated depolarization and dielectric-hysteresis studies, it is possible to explain the processes behind the additional peaks. The former peak, which is associated with the mid-temperature transition, is found in all other vinylidene fluoride-based polymers and may help to understand the non-zero epsilon 2 ' values that are detected on the paraelectric phase of the terpolymer. The latter peak can also be observed during cooling of P(VDF-TrFE) copolymer samples at 100 degrees C and is due to conduction and space-charge polarization as a result of the accumulation of real charges at the electrode-sample interface.}, language = {en} } @article{LiChenQiuetal.2019, author = {Li, Changsheng and Chen, Gangjin and Qiu, Xunlin and Gao, Meng and Gerhard, Reimund}, title = {Modified polytetrafluoroethylene}, series = {Applied physics express : APEX}, volume = {13}, journal = {Applied physics express : APEX}, number = {1}, publisher = {IOP Publ. Ltd.}, address = {Bristol}, issn = {1882-0778}, doi = {10.7567/1882-0786/ab5b23}, pages = {5}, year = {2019}, abstract = {Three poly(tetrafluoroethylene-hexafluoropropylene-vinylidenefluoride) (TFE-HFP-VDF or THV) terpolymers (Dyneon (R)) with different monomer ratios are investigated to demonstrate the concept of "modified" PTFE for space-charge electrets. HFP and VDF monomers distort the highly ordered PTFE molecules, which effectively enhances processability and adversely affects space-charge storage. Particularly, VDF component renders the material polar and probably also more conductive, partially undermining the space-charge-storage capabilities of PTFE. Nevertheless, the terpolymer THV815 with a TFE/HFP/VDF wt\% ratio of 76.1/10.9/13 combines easy processability and relatively good space-charge stability. Our results shed light on novel concepts for space-charge electret materials with enhanced processing properties and reasonable charge-storage capabilities.}, language = {en} } @misc{NguyenGerhard2018, author = {Nguyen, Quyet Doan and Gerhard, Reimund}, title = {LDPE/MgO Nanocomposite Dielectrics for Electrical-Insulation and Ferroelectret-Transducer Applications}, series = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, journal = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6389-9}, pages = {4}, year = {2018}, abstract = {Published results on LDPE/MgO nanocomposites (3wt\%) show that they promise to be good electrical-insulation materials. In this work, the nanocomposites are examined as a potential (ferro-)electret material as well. Isothermal surface-potential decay measurements show that charged LDPE/MgO films still exhibit significant surface potentials after heating for 4 hours at 80 degrees C, which suggests good capabilities of LDPE/MgO nanocomposites to hold electric charges of both polarities. Open-tubular-channel ferroelectrets prepared from LDPE/MgO nanocomposite films show significant piezoelectricity with d(33) coefficients of about 20 pC/N after charging and are stable up to temperatures of at least 80 degrees C. Thus LDPE/MgO nanocomposites may become available as a new ferroelectret material. To increase their d(33) coefficients, it is desirable to optimize the charging conditions and the ferroelectret structure.}, language = {en} } @misc{LouposDamigosTsertouetal.2019, author = {Loupos, Konstantinos and Damigos, Yannis and Tsertou, Athanasisa and Amditis, Angelos and Lenas, Sotiris-Angelos and Chatziandreoglou, Chistos and Malliou, Christina and Tsaoussidis, Vassilis and Gerhard, Reimund and Rychkov, Dmitry and Wirges, Werner and Frankenstein, Bernd and Camarinopoulos, Stephanos and Kalidromitis, Vassilis and Sanna, C. and Maier, Stephanos and Gordt, A. and Panetsos, P.}, title = {Innovative soft-material sensor, wireless network and assessment software for bridge life-cycle assessment}, series = {Life-cycle analysis and assessmanet in civil engineering : towards an integrated vision}, journal = {Life-cycle analysis and assessmanet in civil engineering : towards an integrated vision}, publisher = {CRC Press, Taylor \& Francis Group}, address = {Boca Raton}, isbn = {978-1-315-22891-4}, pages = {2085 -- 2092}, year = {2019}, abstract = {Nowadays, structural health monitoring of critical infrastructures is considered as of primal importance especially for managing transport infrastructure however most current SHM methodologies are based on point-sensors that show various limitations relating to their spatial positioning capabilities, cost of development and measurement range. This publication describes the progress in the SENSKIN EC co-funded research project that is developing a dielectric-elastomer sensor, formed from a large highly extensible capacitance sensing membrane and is supported by an advanced micro-electronic circuitry, for monitoring transport infrastructure bridges. The sensor under development provides spatial measurements of strain in excess of 10\%, while the sensing system is being designed to be easy to install, require low power in operation concepts, require simple signal processing, and have the ability to self-monitor and report. An appropriate wireless sensor network is also being designed and developed supported by local gateways for the required data collection and exploitation. SENSKIN also develops a Decision-Support-System (DSS) for proactive condition-based structural interventions under normal operating conditions and reactive emergency intervention following an extreme event. The latter is supported by a life-cycle-costing (LCC) and life-cycle-assessment (LCA) module responsible for the total internal and external costs for the identified bridge rehabilitation, analysis of options, yielding figures for the assessment of the economic implications of the bridge rehabilitation work and the environmental impacts of the bridge rehabilitation options and of the associated secondary effects respectively. The overall monitoring system will be evaluated and benchmarked on actual bridges of Egnatia Highway (Greece) and Bosporus Bridge (Turkey).}, language = {en} } @misc{RamanVenkatesanFruebingGerhard2018, author = {Raman Venkatesan, Thulasinath and Fr{\"u}bing, Peter and Gerhard, Reimund}, title = {Influence of Composition and Preparation on Crystalline Phases and Morphology in Poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) Relaxor-Ferroelectric Terpolymer}, series = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, journal = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6389-9}, doi = {10.1109/ICD.2018.8514758}, pages = {4}, year = {2018}, abstract = {The influence of chemical composition and crystallisation conditions on the ferroelectric and paraelectric phases and the resulting morphology in Poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer films with 55.4/37.2/7.3 mol\% or with 62.2/29.4/8.4 mol\% of VDF/TrFE/CFE was studied. Poly(vinylidene fluoride trifluoroethylene) (P(VDF-TrFE)) with 75/25 mol\% VDF/TrFE was employed as reference material. Fourier-Transform Infrared Spectroscopy (FTIR) was used to determine the fractions of the relevant terpolymer phases, and X-Ray Diffraction (XRD) was employed to assess the crystalline morphology. The FTIR results show an increase of the fraction of paraelectric phases after annealing. On the other hand, XRD results indicate a more stable paraelectric phase in the terpolymer with higher CFE content.}, language = {en} } @article{RychkovGerhardKuznetsovetal.2018, author = {Rychkov, Dmitry and Gerhard, Reimund and Kuznetsov, Alexey and Rychkov, Andrey}, title = {Influence of charge density on the trap energy spectrum in fluoroethylenepropylene copolymer films with chemically modified surfaces}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {25}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {3}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2018.007437}, pages = {840 -- 844}, year = {2018}, abstract = {Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps.}, language = {en} } @misc{WangRychkovGerhard2018, author = {Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Influence of Charge Density on Charge Decay in Chemically Modified Polypropylene Films}, series = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, journal = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6389-9}, doi = {10.1109/ICD.2018.8514718}, pages = {4}, year = {2018}, abstract = {Previous work has shown that surface modification with orthophosphoric acid can significantly enhance the charge stability on polypropylene (PP) surface by generating deeper traps. In the present study, thermally stimulated potential-decay measurements revealed that the chemical treatment may also significantly increase the number of available trapping sites on the surface. Thus, as a consequence, the so-called "cross-over" phenomenon, which is observed on as-received and thermally treated PP electrets, may be overcome in a certain range of initial charge densities. Furthermore, the discharge behavior of chemically modified samples indicates that charges can be injected from the treated surface into the bulk, and/or charges of opposite polarity can be pulled from the rear electrode into the bulk at elevated temperatures and at the high electric fields that are caused by the deposited charges. In the bulk, a lack of deep traps causes rapid charge decay already in the temperature range around 95 degrees C.}, language = {en} } @misc{GerhardKaltenbrunner2019, author = {Gerhard, Reimund and Kaltenbrunner, Martin}, title = {In Memoriam Siegfried Bauer}, series = {IEEE electrical insulation magazine}, volume = {35}, journal = {IEEE electrical insulation magazine}, number = {2}, publisher = {IEEE}, address = {Piscataway}, issn = {0883-7554}, doi = {10.1109/MEI.2019.8636175}, pages = {76 -- 78}, year = {2019}, abstract = {Siegfried Bauer, an internationally renowned, very creative applied physicist, who also was a prolific materials scientist and engineer, died on December 30, 2018, in Linz, Austria, after a one-year battle with cancer. He was full professor of soft-matter physics at the Johannes Kepler University Linz, Austria, and a scientific leader and innovator across the fields but mainly in the areas of electro-active materials (including electrets) and stretchable and imperceptible electronics.}, language = {en} } @article{FangMaLietal.2017, author = {Fang, Peng and Ma, Xingchen and Li, Xiangxin and Qiu, Xunlin and Gerhard, Reimund and Zhang, Xiaoqing and Li, Guanglin}, title = {Fabrication, Structure Characterization, and Performance Testing of Piezoelectret-Film Sensors for Recording Body Motion}, series = {IEEE Sensors Journal}, volume = {18}, journal = {IEEE Sensors Journal}, number = {1}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1530-437X}, doi = {10.1109/JSEN.2017.2766663}, pages = {401 -- 412}, year = {2017}, abstract = {During muscle contractions, radial-force distributions are generated on muscle surfaces due to muscle-volume changes, from which the corresponding body motions can be recorded by means of so-called force myography (FMG). Piezo- or ferroelectrets are flexible piezoelectric materials with attractive materials and sensing properties. In addition to several other applications, they are suitable for detecting force variations by means of wearable devices. In this paper, we prepared piezoelectrets from cellular polypropylene films by optimizing the fabrication procedures, and developed an FMG-recording system based on piezoelectret sensors. Different hand and wrist movements were successfully detected on able-bodied subjects with the FMG system. The FMG patterns were evaluated and identified by means of linear discriminant analysis and artificial neural network algorithms, and average motion-classification accuracies of 96.1\% and 94.8\%, respectively, were obtained. This paper demonstrates the feasibility of using piezoelectret-film sensors for FMG and may thus lead to alternative methods for detecting body motion and to related applications, e.g., in biomedical engineering or structural-health monitoring.}, language = {en} } @article{RamanVenkatesanGulyakovaFruebingetal.2019, author = {Raman Venkatesan, Thulasinath and Gulyakova, Anna A. and Fr{\"u}bing, Peter and Gerhard, Reimund}, title = {Electrical polarization phenomena, dielectric relaxations and structural transitions in a relaxor-ferroelectric terpolymer investigated with electrical probing techniques}, series = {Materials research express}, volume = {6}, journal = {Materials research express}, number = {12}, publisher = {IOP Publ. Ltd.}, address = {Bristol}, issn = {2053-1591}, doi = {10.1088/2053-1591/ab5352}, pages = {7}, year = {2019}, abstract = {Dielectric Relaxation Spectroscopy (DRS) and Thermally Stimulated Depolarization Current (TSDC) measurements were employed to study dielectric-relaxation processes, structural transitions and electric-polarization phenomena in poly(vinylidenefluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer films. Results from DRS confirm the existence of two separate dispersion regions related to a para-to-ferroelectric phase transition and to the glass transition. The dipolar TSDC peak correlates with the loss peak of the ? relaxation that represents the glass transition. The electric polarization calculated from the dipolar TSDC peak (glass transition) shows a non-linear electric-field dependence and saturates at high electric poling fields. As the observed behaviour is essentially the same as that of the electric polarization obtained from direct polarization-versus-electric-field hysteresis measurements, TSDC experiments are also suitable for studying the polarization in relaxor-ferroelectric polymers. A saturation polarization of 44 mC m(?2) was found for an electric field of 190 MV m(?1).}, language = {en} } @misc{Gerhard2019, author = {Gerhard, Reimund}, title = {Dielectric materials for electro-active (electret) and/or electro-passive (insulation) applications}, series = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, journal = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-8434-4}, doi = {10.1109/ICEMPE.2019.8727276}, pages = {91 -- 96}, year = {2019}, abstract = {Dielectric materials for electret applications usually have to contain a quasi-permanent space charge or dipole polarization that is stable over large temperature ranges and time periods. For electrical-insulation applications, on the other hand, a quasi-permanent space charge or dipole polarization is usually considered detrimental. In recent years, however, with the advent of high-voltage direct-current (HVDC) transmission and high-voltage capacitors for energy storage, new possibilities are being explored in the area of high-voltage dielectrics. Stable charge trapping (as e.g. found in nano-dielectrics) or large dipole polarizations (as e.g. found in relaxor ferroelectrics and high-permittivity dielectrics) are no longer considered to be necessarily detrimental in electrical-insulation materials. On the other hand, recent developments in electro-electrets (dielectric elastomers), i.e. very soft dielectrics with large actuation strains and high breakdown fields, and in ferroelectrets, i.e. polymers with electrically charged cavities, have resulted in new electret materials that may also be useful for HVDC insulation systems. Furthermore, 2-dimensional (nano-particles on surfaces or interfaces) and 3-dimensional (nano-particles in the bulk) nano-dielectrics have been found to provide very good charge-trapping properties that may not only be used for more stable electrets and ferroelectrets, but also for better HVDC electrical-insulation materials with the possibility to optimize charge-transport and field-gradient behavior. In view of these and other recent developments, a first attempt will be made to review a small selection of electro-active (i.e. electret) and electro-passive (i.e. insulation) dielectrics in direct comparison. Such a comparative approach may lead to synergies in materials concepts and research methods that will benefit both areas. Furthermore, electrets may be very useful for sensing and monitoring applications in electrical-insulation systems, while high-voltage technology is essential for more efficient charging and poling of electret materials.}, language = {en} } @article{QiuBenjaminRamanVenkatesanetal.2020, author = {Qiu, Xunlin and Benjamin, Aravindan Joseph and Raman Venkatesan, Thulasinath and Schmidt, Georg C. and Soler, Ricardo Alonso Quintana and Panicker, Pramul Muraleedhara and Gerhard, Reimund and H{\"u}bler, Arved Carl}, title = {Dielectric and electroacoustic assessment of screen-printed piezoelectric polymer layers as flexible transducers}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {27}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {5}, publisher = {Institute of Electrical and Electronics Engineers}, address = {New York, NY}, issn = {1070-9878}, doi = {10.1109/TDEI.2020.008864}, pages = {1683 -- 1690}, year = {2020}, abstract = {Here, piezoelectric transducers consisting of a P(VDF-TrFE) layer with either silver or PEDOT:PSS screen-printed electrodes are studied. The influence of electrodes on the dielectric and electroacoustic properties are studied in dielectric-spectroscopy and ferroelectric-hysteresis measurements. Only when both the bottom and the top electrodes are made of silver, the typical dielectric relaxation of the P(VDF-TrFE) layer is clearly observed. When one or two of the electrodes are of PEDOT:PSS, a Debye-like relaxation is present. Compared with silver electrodes, PEDOT:PSS electrodes allow for moderate self-healing. Consequently, samples with bottom and top PEDOT:PSS electrodes can be poled to saturation, while samples with silver electrodes can hardly be poled to saturation due to destructive electric breakdown. Acoustic transducer measurements show that silver electrodes facilitate higher and broader frequency operation, while PEDOT:PSS electrodes bring slightly lower total harmonic distortion. Overall, the acoustic performance shows no significant deviations between differently electroded samples so that silver electrodes do not offer any advantages for the transducers studied here due to their much higher tendency for destructive electric breakdown.}, language = {en} } @misc{NguyenWangRychkovetal.2019, author = {Nguyen, Quyet Doan and Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Depth Profile and Transport of Positive and Negative Charge in Surface (2-D) and Bulk (3-D) Nanocomposite Films}, series = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, journal = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-8434-4}, doi = {10.1109/ICEMPE.2019.8727256}, pages = {298 -- 300}, year = {2019}, abstract = {In the present study, the charge distribution and the charge transport across the thickness of 2- and 3-dimensional polymer nanodielectrics was investigated. Chemically surface-treated polypropylene (PP) films and low-density polyethylene nanocomposite films with 3 wt \% of magnesium oxide (LDPE/MgO) served as examples of 2-D and 3-D nanodielectrics, respectively. Surface charges were deposited onto the non-metallized surfaces of the one-side metallized polymer films and found to broaden and to thus enter the bulk of the films upon thermal stimulation at suitable elevated temperatures. The resulting space-charge profiles in the thickness direction were probed by means of Piezoelectrically-generated Pressure Steps (PPSs). It was observed that the chemical surface treatment of PP which led to the formation of nano-structures or the use of bulk nanoparticles from LDPE/MgO nanocomposites enhance charge trapping on or in the respective polymer films and also reduce charge transport inside the respective samples.}, language = {en} } @article{QiuGrothWirgesetal.2018, author = {Qiu, Xunlin and Groth, Frederick and Wirges, Werner and Gerhard, Reimund}, title = {Cellular polypropylene foam films as DC voltage insulation and as piezoelectrets}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {25}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {3}, publisher = {Institut of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2018.007192}, pages = {829 -- 834}, year = {2018}, abstract = {Polymer foams are in industrial use for several decades. More recently, non-polar polymer foams were found to be piezoelectric (so-called piezoelectrets) after internal electrical charging of the cavities. So far, few studies have been carried out on the electrical-insulation properties of polymer foams. Here, we compare the piezoelectric and the DC-voltage electrical-insulation properties of cellular polypropylene (PP) foams. Their cavity microstructure can be adjusted via inflation in high-pressure nitrogen gas in combination with a subsequent thermal treatment. While inflation is effective for improving the piezoelectricity, it is detrimental for the electrical-insulation properties. The original cellular PP foam shows a breakdown strength of approximately 230 MV/m, within the same range as that of solid PP. The breakdown strength decreases with increasing degree of inflation, and the dependence on the foam thickness follows an inverse power law with an exponent of 1.2. Nevertheless, up to a thickness of 140 mu m (3.5 times the original thickness), the breakdown strength of cellular-foam PP films is at least 7 times that of an air gap with the same thickness. In addition, the influence of high temperatures and high humidities on the piezoelectricity and the breakdown strength of cellular PP was studied. It was found that the piezoelectric d(33) coefficient decays rapidly already at 70 degrees C, while the breakdown strength slightly increases during storage at 70 or 90 degrees C. Under a relative humidity of 95\%, the breakdown strength increases with storage time, while the piezoelectric d(33) coefficient slightly decreases.}, language = {en} } @article{HeWangHeetal.2022, author = {He, Yushuang and Wang, Feipeng and He, Li and Wang, Qiang and Li, Jian and Qian, Yihua and Gerhard, Reimund and Plath, Ronald}, title = {An insight Into the role of Nano-Alumina on DC Flashover-Resistance and surface charge variation of Epoxy Nanocomposites}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {29}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {3}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2022.3173510}, pages = {1022 -- 1029}, year = {2022}, abstract = {The addition of nano-Al2O3 has been shown to enhance the breakdown voltage of epoxy resin, but its flashover results appeared with disputation. This work concentrates on the surface charge variation and dc flashover performance of epoxy resin with nano-Al2O3 doping. The dispersion of nano-Al2O3 in epoxy is characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The dc flashover voltages of samples under either positive or negative polarity are measured with a finger-electrode system, and the surface charge variations before and after flashovers were identified from the surface potential mapping. The results evidence that nano-Al2O3 would lead to a 16.9\% voltage drop for the negative flashovers and a 6.8\% drop for positive cases. It is found that one-time flashover clears most of the accumulated surface charges, regardless of positive or negative. As a result, the ground electrode is neighbored by an equipotential zone enclosed with low-density heterocharges. The equipotential zone tends to be broadened after 20 flashovers. The nano-Al2O3 is noticed as beneficial to downsize the equipotential zone due to its capability on charge migration, which is reasonable to maintain flashover voltage at a high level after multiple flashovers. Hence, nano-Al2O3 plays a significant role in improving epoxy with high resistance to multiple flashovers.}, language = {en} } @article{AssagraAltafimdoCarmoetal.2020, author = {Assagra, Yuri A.O. and Altafim, Ruy Alberto Pisani and do Carmo, Joao P. and Altafim, Ruy A.C. and Rychkov, Dmitry and Wirges, Werner and Gerhard, Reimund}, title = {A new route to piezo-polymer transducers: 3D printing of polypropylene ferroelectrets}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {27}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {5}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2020.008461}, pages = {1668 -- 1674}, year = {2020}, abstract = {Here, a promising approach for producing piezo-polymer transducers in a one-step process is presented. Using 3D-printing technology and polypropylene (PP) filaments, we are able to print a two-layered film structure with regular cavities of precisely controlled size and shape. It is found that the 3D-printed samples exhibit piezoelectric coefficients up to 200 pC/N, similar to those of other PP ferroelectrets, and their temporal and thermal behavior is in good agreement with those known of PP ferroelectrets. The piezoelectric response strongly decreases for applied pressures above 20 kPa, as the pressure in the air-filled cavities strongly influences the overall elastic modulus of ferroelectrets.}, language = {en} }