@article{EvsevleevMishurovaCabezaetal.2018, author = {Evsevleev, Sergei and Mishurova, Tatiana and Cabeza, Sandra and Koos, R. and Sevostianov, Igor and Garc{\´e}s, Gonzales and Requena, Guillermo and Fernandez, R. and Bruno, Giovanni}, title = {The role of intermetallics in stress partitioning and damage evolution of AlSil2CuMgNi alloy}, series = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, volume = {736}, journal = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.08.070}, pages = {453 -- 464}, year = {2018}, abstract = {Load partitioning between phases in a cast AlSi12CuMgNi alloy was investigated by in-situ compression test during neutron diffraction experiments. Computed tomography (CT) was used to determine volume fractions of eutectic Si and intermetallic (IM) phases, and to assess internal damage after ex-situ compression tests. The CT reconstructed volumes showed the interconnectivity of IM phases, which build a 3D network together with eutectic Si. Large stresses were found in IMs, revealing their significant role as a reinforcement for the alloy. An existing micromechanical model based on Maxwell scheme was extended to the present case, assuming the alloy as a three-phase composite (Al matrix, eutectic Si, IM phases). The model agrees well with the experimental data. Moreover, it allows predicting the principal stresses in each phase, while experiments can only determine stress differences between the axial and radial sample directions. Finally, we showed that the addition of alloying elements not only allowed developing a 3D interconnected network, but also improved the strength of the Al matrix, and the ability of the alloy constituents to bear mechanical load.}, language = {en} } @article{EvsevleevPaciornikBruno2020, author = {Evsevleev, Sergei and Paciornik, Sidnei and Bruno, Giovanni}, title = {Advanced deep learning-based 3D microstructural characterization of multiphase metal matrix composites}, series = {Advanced engineering materials}, volume = {22}, journal = {Advanced engineering materials}, number = {4}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1438-1656}, doi = {10.1002/adem.201901197}, pages = {6}, year = {2020}, abstract = {The quantitative analysis of microstructural features is a key to understanding the micromechanical behavior of metal matrix composites (MMCs), which is a premise for their use in practice. Herein, a 3D microstructural characterization of a five-phase MMC is performed by synchrotron X-ray computed tomography (SXCT). A workflow for advanced deep learning-based segmentation of all individual phases in SXCT data is shown using a fully convolutional neural network with U-net architecture. High segmentation accuracy is achieved with a small amount of training data. This enables extracting unprecedently precise microstructural parameters (e.g., volume fractions and particle shapes) to be input, e.g., in micromechanical models.}, language = {en} } @article{MishurovaBrunoEvsevleevetal.2020, author = {Mishurova, Tatiana and Bruno, Giovanni and Evsevleev, Sergei and Sevostianov, Igor}, title = {Determination of macroscopic stress from diffraction experiments}, series = {Journal of applied physics}, volume = {128}, journal = {Journal of applied physics}, number = {2}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/5.0009101}, pages = {14}, year = {2020}, abstract = {The paper is motivated by some inconsistencies and contradictions present in the literature on the calculation of the so-called diffraction elastic constants. In an attempt at unifying the views that the two communities of Materials Science and Mechanics of Materials have on the subject, we revisit and define the terminology used in the field. We also clarify the limitations of the commonly used approaches and show that a unified methodology is also applicable to textured materials with a nearly arbitrary grain shape. We finally compare the predictions based on this methodology with experimental data obtained by in situ synchrotron radiation diffraction on additively manufactured Ti-6Al-4V alloy. We show that (a) the transverse isotropy of the material yields good agreement between the best-fit isotropy approximation (equivalent to the classic Kroner's model) and the experimental data and (b) the use of a general framework allows the calculation of all components of the tensor of diffraction elastic constants, which are not easily measurable by diffraction methods. This allows us to extend the current state-of-the-art with a predictive tool.}, language = {en} } @article{ChenMuellerPrinzetal.2020, author = {Chen, Cong and M{\"u}ller, Bernd R. and Prinz, Carsten and Stroh, Julia and Feldmann, Ines and Bruno, Giovanni}, title = {The correlation between porosity characteristics and the crystallographic texture in extruded stabilized aluminium titanate for diesel particulate filter applications}, series = {Journal of the European Ceramic Society}, volume = {40}, journal = {Journal of the European Ceramic Society}, number = {4}, publisher = {Elsevier}, address = {Oxford}, issn = {0955-2219}, doi = {10.1016/j.jeurceramsoc.2019.11.076}, pages = {1592 -- 1601}, year = {2020}, abstract = {Porous ceramic diesel particulate filters (DPFs) are extruded products that possess macroscopic anisotropic mechanical and thermal properties. This anisotropy is caused by both morphological features (mostly the orientation of porosity) and crystallographic texture. We systematically studied those two aspects in two aluminum titanate ceramic materials of different porosity using mercury porosimetry, gas adsorption, electron microscopy, X-ray diffraction, and X-ray refraction radiography. We found that a lower porosity content implies a larger isotropy of both the crystal texture and the porosity orientation. We also found that, analogous to cordierite, crystallites do align with their axis of negative thermal expansion along the extrusion direction. However, unlike what found for cordierite, the aluminium titanate crystallite form is such that a more pronounced (0 0 2) texture along the extrusion direction implies porosity aligned perpendicular to it.}, language = {en} } @article{ThiedeCabezaMishurovaetal.2018, author = {Thiede, Tobias and Cabeza, Sandra and Mishurova, Tatiana and Nadammal, Naresh and Kromm, Arne and Bode, Johannes and Haberland, Christoph and Bruno, Giovanni}, title = {Residual Stress in Selective Laser Melted Inconel 718}, series = {Materials performance and characterization}, volume = {7}, journal = {Materials performance and characterization}, number = {4}, publisher = {American Society for Testing and Materials}, address = {West Conshohocken}, issn = {2379-1365}, doi = {10.1520/MPC20170119}, pages = {717 -- 735}, year = {2018}, abstract = {The residual stress distribution in IN718 elongated prisms produced by selective laser melting was studied by means of neutron (bulk) and laboratory X-ray (surface) diffraction. Two deposition hatch lengths were considered. A horizontal plane near the top surface (perpendicular to the building direction) and a vertical plane near the lateral surface (parallel to the building direction) were investigated. Samples both in as-built (AB) condition and removed from the base plate (RE) were characterized. While surface stress fields seem constant for the AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements. Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e., with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the base plate.}, language = {en} } @article{ErdmannKupschMuelleretal.2019, author = {Erdmann, Maren and Kupsch, Andreas and M{\"u}ller, Bernd Randolf and Hentschel, Manfred P. and Niebergall, Ute and B{\"o}hning, Martin and Bruno, Giovanni}, title = {Diesel-induced transparency of plastically deformed high-density polyethylene}, series = {Journal of materials science}, volume = {54}, journal = {Journal of materials science}, number = {17}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-019-03700-8}, pages = {11739 -- 11755}, year = {2019}, abstract = {High-density polyethylene becomes optically transparent during tensile drawing when previously saturated with diesel fuel. This unusual phenomenon is investigated as it might allow conclusions with respect to the material behavior. Microscopy, differential scanning calorimetry, density measurements are applied together with two scanning X-ray scattering techniques: wide angle X-ray scattering (WAXS) and X-ray refraction, able to extract the spatially resolved crystal orientation and internal surface, respectively. The sorbed diesel softens the material and significantly alters the yielding characteristics. Although the crystallinity among stretched regions is similar, a virgin reference sample exhibits strain whitening during stretching, while the diesel-saturated sample becomes transparent. The WAXS results reveal a pronounced fiber texture in the tensile direction in the stretched region and an isotropic orientation in the unstretched region. This texture implies the formation of fibrils in the stretched region, while spherulites remain intact in the unstretched parts of the specimens. X-ray refraction reveals a preferred orientation of internal surfaces along the tensile direction in the stretched region of virgin samples, while the sample stretched in the diesel-saturated state shows no internal surfaces at all. Besides from stretching saturated samples, optical transparency is also obtained from sorbing samples in diesel after stretching.}, language = {en} } @article{MackLaquaiMuelleretal.2019, author = {Mack, Daniel Emil and Laquai, Rene and Mueller, Bernd and Helle, Oliver and Sebold, Doris and Vassen, Robert and Bruno, Giovanni}, title = {Evolution of porosity, crack density, and CMAS penetration in thermal barrier coatings subjected to burner rig testing}, series = {Journal of the American Ceramic Society}, volume = {102}, journal = {Journal of the American Ceramic Society}, number = {10}, publisher = {Wiley}, address = {Hoboken}, issn = {0002-7820}, doi = {10.1111/jace.16465}, pages = {6163 -- 6175}, year = {2019}, abstract = {Degradation of thermal barrier coatings (TBCs) in gas-turbine engines due to calcium-magnesium-aluminosilicate (CMAS) glassy deposits from various sources has been a persistent issue since many years. In this study, state of the art electron microscopy was correlated with X-ray refraction techniques to elucidate the intrusion of CMAS into the porous structure of atmospheric plasma sprayed (APS) TBCs and the formation and growth of cracks under thermal cycling in a burner rig. Results indicate that the sparse nature of the infiltration as well as kinetics in the burner rig are majorly influenced by the wetting behavior of the CMAS. Despite the obvious attack of CMAS on grain boundaries, the interaction of yttria-stabilized zirconia (YSZ) with intruded CMAS has no immediate impact on structure and density of internal surfaces. At a later stage the formation of horizontal cracks is observed in a wider zone of the TBC layer.}, language = {en} } @article{MishurovaArtztHaubrichetal.2018, author = {Mishurova, Tatiana and Artzt, Katia and Haubrich, Jan and Requena, Guillermo and Bruno, Giovanni}, title = {New aspects about the search for the most relevant parameters optimizing SLM materials}, series = {Additive manufacturing}, volume = {25}, journal = {Additive manufacturing}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2214-8604}, doi = {10.1016/j.addma.2018.11.023}, pages = {325 -- 334}, year = {2018}, abstract = {While the volumetric energy density is commonly used to qualify a process parameter set, and to quantify its influence on the microstructure and performance of additively manufactured (AM) materials and components, it has been already shown that this description is by no means exhaustive. In this work, new aspects of the optimization of the selective laser melting process are investigated for AM Ti-6Al-4V. We focus on the amount of near-surface residual stress (RS), often blamed for the failure of components, and on the porosity characteristics (amount and spatial distribution). First, using synchrotron x-ray diffraction we show that higher RS in the subsurface region is generated if a lower energy density is used. Second, we show that laser de-focusing and sample positioning inside the build chamber also play an eminent role, and we quantify this influence. In parallel, using X-ray Computed Tomography, we observe that porosity is mainly concentrated in the contour region, except in the case where the laser speed is small. The low values of porosity (less than 1\%) do not influence RS.}, language = {en} } @article{StegemannCabezaPelkneretal.2018, author = {Stegemann, Robert and Cabeza, Sandra and Pelkner, Matthias and Lyamkin, Viktor and Pittner, Andreas and Werner, Daniel and Wimpory, Robert and Boin, Mirko and Kreutzbruck, Marc and Bruno, Giovanni}, title = {Influence of the microstructure on magnetic stray fields of low-carbon steel welds}, series = {Journal of Nondestructive Evaluation}, volume = {37}, journal = {Journal of Nondestructive Evaluation}, number = {3}, publisher = {Springer}, address = {New York}, issn = {0195-9298}, doi = {10.1007/s10921-018-0522-0}, pages = {18}, year = {2018}, abstract = {This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction. Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields.}, language = {en} } @article{FernandezCabezaMishurovaetal.2018, author = {Fernandez, R. and Cabeza, Sandra and Mishurova, Tatiana and Fernandez-Castrillo, P. and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Residual stress and yield strength evolution with annealing treatments in an age-hardenable aluminum alloy matrix composite}, series = {Materials Science and Engineering: A}, volume = {731}, journal = {Materials Science and Engineering: A}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.06.031}, pages = {344 -- 350}, year = {2018}, abstract = {We investigated the possibility of minimizing tensile matrix residual stresses in age hardenable aluminum alloy metal matrix composites without detrimentally affect their mechanical properties (such as yield strength). Specifically, we performed thermal treatments at different temperatures and times in an age-hardenable aluminum matrix composite 2014Al-15vol\%Al2O3. Using X-ray synchrotron radiation diffraction and mechanical tests, we show that below a certain treatment temperature (250 degrees C) it is possible to identify an appropriate thermal treatment capable of relaxing residual stress in this composite while even increasing its yield strength, with respect to the as processed conditions.}, language = {en} }