@article{KegelmannTockhornWolffetal.2019,
  author    = {Kegelmann, Lukas and Tockhorn, Philipp and Wolff, Christian Michael and M{\´a}rquez, Jos{\´e} A. and Caicedo D{\´a}vila, Sebasti{\´a}n and Korte, Lars and Unold, Thomas and Loevenich, Wilfried and Neher, Dieter and Rech, Bernd and Albrecht, Steve},
  title     = {Mixtures of Dopant-Free Spiro-OMeTAD and Water-Free PEDOT as a Passivating Hole Contact in Perovskite Solar Cells},
  series = {ACS applied materials \& interfaces},
  volume    = {11},
  journal   = {ACS applied materials \& interfaces},
  number    = {9},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1944-8244},
  doi       = {10.1021/acsami.9b01332},
  pages     = {9172 -- 9181},
  year      = {2019},
  abstract  = {Doped spiro-OMeTAD at present is the most commonly used hole transport material (HTM) in n-i-p-type perovskite solar cells, enabling high efficiencies around 22\%. However, the required dopants were shown to induce nonradiative recombination of charge carriers and foster degradation of the solar cell. Here, in a novel approach, highly conductive and inexpensive water-free poly(3,4-ethylenedioxythiophene) (PEDOT) is used to replace these dopants. The resulting spiro-OMeTAD/PEDOT (SpiDOT) mixed films achieve higher lateral conductivities than layers of doped spiro-OMeTAD. Furthermore, combined transient and steady-state photoluminescence studies reveal a passivating effect of PEDOT, suppressing nonradiative recombination losses at the perovskite/HTM interface. This enables excellent quasi-Fermi level splitting values of up to 1.24 eV in perovskite/SpiDOT layer stacks and high open-circuit voltages (V-OC) up to 1.19 V in complete solar cells. Increasing the amount of dopant-free spiro-OMeTAD in SpiDOT layers is shown to enhance hole extraction and thereby improves the fill factor in solar cells. As a consequence, stabilized efficiencies up to 18.7\% are realized, exceeding cells with doped spiro-OMeTAD as a HTM in this study. Moreover, to the best of our knowledge, these results mark the lowest nonradiative recombination loss in the V-OC (140 mV with respect to the Shockley-Queisser limit) and highest efficiency reported so far for perovskite solar cells using PEDOT as a HTM.},
  language  = {en}
}
@article{JoštAlbrechtKegelmannetal.2017,
  author    = {Jošt, Marko and Albrecht, Steve and Kegelmann, Lukas and Wolff, Christian Michael and Lang, Felix and Lipovšek, Benjamin and Krč, Janez and Korte, Lars and Neher, Dieter and Rech, Bernd and Topič, Marko},
  title     = {Efficient light management by textured nanoimprinted layers for perovskite solar cells},
  series = {ACS photonics},
  volume    = {4},
  journal   = {ACS photonics},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2330-4022},
  doi       = {10.1021/acsphotonics.7b00138},
  pages     = {1232 -- 1239},
  year      = {2017},
  abstract  = {Inorganic-organic perovskites like methylammonium-lead-iodide have proven to be an effective class of 17 materials for fabricating efficient solar cells. To improve their performance, light management techniques using textured surfaces, similar to those used in established solar cell technologies, should be considered. Here, we apply a light management foil created by UV nanoimprint lithography on the glass side of an inverted (p-i-n) perovskite solar cell with 16.3\% efficiency. The obtained 1 mA cm(-2) increase in the short-circuit current density translates to a relative improvement in cell performance of 5\%, which results in a power conversion efficiency of 17.1\%. Optical 3D simulations based on experimentally obtained parameters were used to support the experimental findings. A good match between the simulated and experimental data was obtained, validating the model. Optical simulations reveal that the main improvement in device performance is due to a reduction in total reflection and that relative improvement in the short-circuit current density of up to 10\% is possible for large-area devices. Therefore, our results present the potential of light management foils for improving the device performance of perovskite solar cells and pave the way for further use of optical simulations in the field of perovskite solar cells.},
  language  = {en}
}
@article{BraungerMundtWolffetal.2018,
  author    = {Braunger, Steffen and Mundt, Laura E. and Wolff, Christian Michael and Mews, Mathias and Rehermann, Carolin and Jost, Marko and Tejada, Alvaro and Eisenhauer, David and Becker, Christiane and Andres Guerra, Jorge and Unger, Eva and Korte, Lars and Neher, Dieter and Schubert, Martin C. and Rech, Bernd and Albrecht, Steve},
  title     = {Cs(x)FA(1-x)Pb(l(1-y)Br(y))(3) Perovskite Compositions},
  series = {The journal of physical chemistry : C, Nanomaterials and interfaces},
  volume    = {122},
  journal   = {The journal of physical chemistry : C, Nanomaterials and interfaces},
  number    = {30},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1932-7447},
  doi       = {10.1021/acs.jpcc.8b06459},
  pages     = {17123 -- 17135},
  year      = {2018},
  abstract  = {We report on the formation of wrinkle-patterned surface morphologies in cesium formamidinium-based Cs(x)FA(1-y)Pb(I1-yBry)(3) perovskite compositions with x = 0-0.3 and y = 0-0.3 under various spin-coating conditions. By varying the Cs and Br contents, the perovskite precursor solution concentration and the spin-coating procedure, the occurrence and characteristics of the wrinkle-shaped morphology can be tailored systematically. Cs(0.17)FA(0.83)Pb(I0.83Br0.17)(3) perovskite layers were analyzed regarding their surface roughness, microscopic structure, local and overall composition, and optoelectronic properties. Application of these films in p-i-n perovskite solar cells (PSCs) with indium-doped tin oxide/NiOx/perovskite/C-60/bathocuproine/Cu architecture resulted in up to 15.3 and 17.0\% power conversion efficiency for the flat and wrinkled morphology, respectively. Interestingly, we find slightly red-shifted photoluminescence (PL) peaks for wrinkled areas and we are able to directly correlate surface topography with PL peak mapping. This is attributed to differences in the local grain size, whereas there is no indication for compositional demixing in the films. We show that the perovskite composition, crystallization kinetics, and layer thickness strongly influence the formation of wrinkles which is proposed to be related to the release of compressive strain during perovskite crystallization. Our work helps us to better understand film formation and to further improve the efficiency of PSCs with widely used mixed-perovskite compositions.},
  language  = {en}
}