@article{PolomAlrshdanAlHalbounietal.2018, author = {Polom, Ulrich and Alrshdan, Hussam and Al-Halbouni, Djamil and Holohan, Eoghan P. and Dahm, Torsten and Sawarieh, Ali and Atallah, Mohamad Y. and Krawczyk, Charlotte M.}, title = {Shear wave reflection seismic yields subsurface dissolution and subrosion patterns}, series = {Solid earth}, volume = {9}, journal = {Solid earth}, number = {5}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1869-9510}, doi = {10.5194/se-9-1079-2018}, pages = {1079 -- 1098}, year = {2018}, abstract = {Near-surface geophysical imaging of alluvial fan settings is a challenging task but crucial for understating geological processes in such settings. The alluvial fan of Ghor Al-Haditha at the southeast shore of the Dead Sea is strongly affected by localized subsidence and destructive sinkhole collapses, with a significantly increasing sinkhole formation rate since ca. 1983. A similar increase is observed also on the western shore of the Dead Sea, in correlation with an ongoing decline in the Dead Sea level. Since different structural models of the upper 50 m of the alluvial fan and varying hypothetical sinkhole processes have been suggested for the Ghor Al-Haditha area in the past, this study aimed to clarify the subsurface characteristics responsible for sinkhole development. For this purpose, high-frequency shear wave reflection vibratory seismic surveys were carried out in the Ghor Al-Haditha area along several crossing and parallel profiles with a total length of 1.8 and 2.1 km in 2013 and 2014, respectively. The sedimentary architecture of the alluvial fan at Ghor Al-Haditha is resolved down to a depth of nearly 200 m at a high resolution and is calibrated with the stratigraphic profiles of two boreholes located inside the survey area. The most surprising result of the survey is the absence of evidence of a thick (>2-10 m) compacted salt layer formerly suggested to lie at ca. 35-40 m depth. Instead, seismic reflection amplitudes and velocities image with good continuity a complex interlocking of alluvial fan deposits and lacustrine sediments of the Dead Sea between 0 and 200 m depth. Furthermore, the underground section of areas affected by sinkholes is characterized by highly scattering wave fields and reduced seismic interval velocities. We propose that the Dead Sea mud layers, which comprise distributed inclusions or lenses of evaporitic chloride, sulfate, and carbonate minerals as well as clay silicates, become increasingly exposed to unsaturated water as the sea level declines and are consequently destabilized and mobilized by both dissolution and physical erosion in the subsurface. This new interpretation of the underlying cause of sinkhole development is supported by surface observations in nearby channel systems. Overall, this study shows that shear wave seismic reflection technique is a promising method for enhanced near-surface imaging in such challenging alluvial fan settings.}, language = {en} } @article{AlHalbouniHolohanTaherietal.2018, author = {Al-Halbouni, Djamil and Holohan, Eoghan P. and Taheri, Abbas and Sch{\"o}pfer, Martin P. J. and Emam, Sacha and Dahm, Torsten}, title = {Geomechanical modelling of sinkhole development using distinct elements}, series = {Solid earth}, volume = {9}, journal = {Solid earth}, number = {6}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1869-9510}, doi = {10.5194/se-9-1341-2018}, pages = {1341 -- 1373}, year = {2018}, abstract = {Mechanical and/or chemical removal of material from the subsurface may generate large subsurface cavities, the destabilisation of which can lead to ground collapse and the formation of sinkholes. Numerical simulation of the interaction of cavity growth, host material deformation and overburden collapse is desirable to better understand the sinkhole hazard but is a challenging task due to the involved high strains and material discontinuities. Here, we present 2-D distinct element method numerical simulations of cavity growth and sinkhole development. Firstly, we simulate cavity formation by quasi-static, stepwise removal of material in a single growing zone of an arbitrary geometry and depth. We benchmark this approach against analytical and boundary element method models of a deep void space in a linear elastic material. Secondly, we explore the effects of properties of different uniform materials on cavity stability and sinkhole development. We perform simulated biaxial tests to calibrate macroscopic geotechnical parameters of three model materials representative of those in which sinkholes develop at the Dead Sea shoreline: mud, alluvium and salt. We show that weak materials do not support large cavities, leading to gradual sagging or suffusion-style subsidence. Strong materials support quasi-stable to stable cavities, the overburdens of which may fail suddenly in a caprock or bedrock collapse style. Thirdly, we examine the consequences of layered arrangements of weak and strong materials. We find that these are more susceptible to sinkhole collapse than uniform materials not only due to a lower integrated strength of the overburden but also due to an inhibition of stabilising stress arching. Finally, we compare our model sinkhole geometries to observations at the Ghor Al-Haditha sinkhole site in Jordan. Sinkhole depth / diameter ratios of 0.15 in mud, 0.37 in alluvium and 0.33 in salt are reproduced successfully in the calibrated model materials. The model results suggest that the observed distribution of sinkhole depth / diameter values in each material type may partly reflect sinkhole growth trends.}, language = {en} } @article{HenschDahmRitteretal.2019, author = {Hensch, Martin and Dahm, Torsten and Ritter, Joachim and Heimann, Sebastian and Schmidt, Bernd and Stange, Stefan and Lehmann, Klaus}, title = {Deep low-frequency earthquakes reveal ongoing magmatic recharge beneath Laacher See Volcano (Eifel, Germany)}, series = {Geophysical journal international}, volume = {216}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggy532}, pages = {2025 -- 2036}, year = {2019}, abstract = {The occurrence of deep low-frequency (DLF) microearthquakes beneath volcanoes is commonly attributed to mass transport in the volcanic plumbing system and used to infer feeding channels from and into magma reservoirs. The key question is how magmas migrate from depth to the shallow crust and whether magma reservoirs are currently being recharged. For the first time since the improvement of the local seismic networks in the East Eifel region (Rhineland-Palatinate, Germany), we detect and locate recurrent DLF earthquakes in the lower crust and upper mantle beneath the Laacher See Volcano (LSV), using a joint data set of permanent sensors and a temporary deployment. So far, eight DLF earthquake sequences were observed in four distinct clusters between 10 and 40 km depth. These clusters of weak events (M-L< 2) align along an approximately 80. southeast dipping line south of the LSV. Moment tensor solutions of these events have large shear components, and the irregular dispersion and long coda of body waves indicate interaction processes between shear cracks and fluids. We find a rotation of P-axes orientation for shallow tectonic earthquakes compared to DLF events, indicating that the stress field in the depth interval of DLF events might favour a vertical migration of magma or magmatic fluids. The caldera of the LSV was formed by the last major eruption of the East Eifel Volcanic Field only 12.9 kyr ago, fed by a shallow magma chamber at 5-8 km depth and erupting a total magma volume of 6.7 km(3). The observed DLF earthquake activity and continuous volcanic gas emissions around the LSV indicate an active magmatic system, possibly connected with an upper mantle melt zone.}, language = {en} } @article{PirliHainzlSchweitzeretal.2018, author = {Pirli, Myrto and Hainzl, Sebastian and Schweitzer, Johannes and K{\"o}hler, Andreas and Dahm, Torsten}, title = {Localised thickening and grounding of an Antarctic ice shelf from tidal triggering and sizing of cryoseismicity}, series = {Earth \& planetary science letters}, volume = {503}, journal = {Earth \& planetary science letters}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0012-821X}, doi = {10.1016/j.epsl.2018.09.024}, pages = {78 -- 87}, year = {2018}, abstract = {We observe remarkably periodic patterns of seismicity rates and magnitudes at the Fimbul Ice Shelf, East Antarctica, correlating with the cycles of the ocean tide. Our analysis covers 19 years of continuous seismic recordings from Antarctic broadband stations. Seismicity commences abruptly during austral summer 2011 at a location near the ocean front in a shallow water region. Dozens of highly repetitive events occur in semi-diurnal cycles, with magnitudes and rates fluctuating steadily with the tide. In contrast to the common unpredictability of earthquake magnitudes, the event magnitudes show deterministic trends within single cycles and strong correlations with spring tides and tide height. The events occur quasi-periodically and the highly constrained event sources migrate landwards during rising tide. We show that a simple, mechanical model can explain most of the observations. Our model assumes stick-slip motion on a patch of grounded ice shelf, which is forced by the variations of the ocean-tide height and ice flow. The well fitted observations give new insights into the general process of frictional triggering of earthquakes, while providing independent evidence of variations in ice shelf thickness and grounding.}, language = {en} } @misc{AlHalbouniHolohanTaherietal.2018, author = {Al-Halbouni, Djamil and Holohan, Eoghan P. and Taheri, Abbas and Sch{\"o}pfer, Martin P. J. and Emam, Sacha and Dahm, Torsten}, title = {Geomechanical modelling of sinkhole development using distinct elements}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, number = {1061}, issn = {1866-8372}, doi = {10.25932/publishup-46843}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-468435}, pages = {35}, year = {2018}, abstract = {Mechanical and/or chemical removal of material from the subsurface may generate large subsurface cavities, the destabilisation of which can lead to ground collapse and the formation of sinkholes. Numerical simulation of the interaction of cavity growth, host material deformation and overburden collapse is desirable to better understand the sinkhole hazard but is a challenging task due to the involved high strains and material discontinuities. Here, we present 2-D distinct element method numerical simulations of cavity growth and sinkhole development. Firstly, we simulate cavity formation by quasi-static, stepwise removal of material in a single growing zone of an arbitrary geometry and depth. We benchmark this approach against analytical and boundary element method models of a deep void space in a linear elastic material. Secondly, we explore the effects of properties of different uniform materials on cavity stability and sinkhole development. We perform simulated biaxial tests to calibrate macroscopic geotechnical parameters of three model materials representative of those in which sinkholes develop at the Dead Sea shoreline: mud, alluvium and salt. We show that weak materials do not support large cavities, leading to gradual sagging or suffusion-style subsidence. Strong materials support quasi-stable to stable cavities, the overburdens of which may fail suddenly in a caprock or bedrock collapse style. Thirdly, we examine the consequences of layered arrangements of weak and strong materials. We find that these are more susceptible to sinkhole collapse than uniform materials not only due to a lower integrated strength of the overburden but also due to an inhibition of stabilising stress arching. Finally, we compare our model sinkhole geometries to observations at the Ghor Al-Haditha sinkhole site in Jordan. Sinkhole depth ∕ diameter ratios of 0.15 in mud, 0.37 in alluvium and 0.33 in salt are reproduced successfully in the calibrated model materials. The model results suggest that the observed distribution of sinkhole depth ∕ diameter values in each material type may partly reflect sinkhole growth trends.}, language = {en} } @misc{PolomAlrshdanAlHalbounietal.2018, author = {Polom, Ulrich and Alrshdan, Hussam and Al-Halbouni, Djamil and Holohan, Eoghan P. and Dahm, Torsten and Sawarieh, Ali and Atallah, Mohamad Y. and Krawczyk, Charlotte M.}, title = {Shear wave reflection seismic yields subsurface dissolution and subrosion patterns}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, number = {979}, issn = {1866-8372}, doi = {10.25932/publishup-45913}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-459134}, pages = {1079 -- 1098}, year = {2018}, abstract = {Near-surface geophysical imaging of alluvial fan settings is a challenging task but crucial for understating geological processes in such settings. The alluvial fan of Ghor Al-Haditha at the southeast shore of the Dead Sea is strongly affected by localized subsidence and destructive sinkhole collapses, with a significantly increasing sinkhole formation rate since ca. 1983. A similar increase is observed also on the western shore of the Dead Sea, in correlation with an ongoing decline in the Dead Sea level. Since different structural models of the upper 50 m of the alluvial fan and varying hypothetical sinkhole processes have been suggested for the Ghor Al-Haditha area in the past, this study aimed to clarify the subsurface characteristics responsible for sinkhole development. For this purpose, high-frequency shear wave reflection vibratory seismic surveys were carried out in the Ghor Al-Haditha area along several crossing and parallel profiles with a total length of 1.8 and 2.1 km in 2013 and 2014, respectively. The sedimentary architecture of the alluvial fan at Ghor Al-Haditha is resolved down to a depth of nearly 200 m at a high resolution and is calibrated with the stratigraphic profiles of two boreholes located inside the survey area. The most surprising result of the survey is the absence of evidence of a thick (> 2-10 m) compacted salt layer formerly suggested to lie at ca. 35-40 m depth. Instead, seismic reflection amplitudes and velocities image with good continuity a complex interlocking of alluvial fan deposits and lacustrine sediments of the Dead Sea between 0 and 200 m depth. Furthermore, the underground section of areas affected by sinkholes is characterized by highly scattering wave fields and reduced seismic interval velocities. We propose that the Dead Sea mud layers, which comprise distributed inclusions or lenses of evaporitic chloride, sulfate, and carbonate minerals as well as clay silicates, become increasingly exposed to unsaturated water as the sea level declines and are consequently destabilized and mobilized by both dissolution and physical erosion in the subsurface. This new interpretation of the underlying cause of sinkhole development is supported by surface observations in nearby channel systems. Overall, this study shows that shear wave seismic reflection technique is a promising method for enhanced near-surface imaging in such challenging alluvial fan settings.}, language = {en} } @article{CescaHeimannKriegerowskietal.2017, author = {Cesca, Simone and Heimann, Sebastian and Kriegerowski, Marius and Saul, Joachim and Dahm, Torsten}, title = {Moment tensor inversion for nuclear explosions}, series = {Seismological research letters}, volume = {88}, journal = {Seismological research letters}, number = {2A}, publisher = {Seismological Society of America}, address = {Albany}, issn = {0895-0695}, doi = {10.1785/0220160139}, pages = {300 -- 310}, year = {2017}, abstract = {Two nuclear explosions were carried out by the Democratic People's Republic of North Korea in January and September 2016. Epicenters were located close to those of the 2006, 2009, and 2013 previous explosions. We perform a seismological analysis of the 2016 events combining the analysis of full waveforms at regional distances and seismic array beams at teleseismic distances. We estimate the most relevant source parameters, such as source depth, moment release, and full moment tensor (MT). The best MT solution can be decomposed into an isotropic source, directly related with the explosion and an additional deviatoric term, likely due to near-source interactions with topographic and/or underground facilities features. We additionally perform an accurate resolution test to assess source parameters uncertainties and trade-offs. This analysis sheds light on source parameters inconsistencies among studies on previous shallow explosive sources. The resolution of the true MT is hindered by strong source parameters trade-offs, so that a broad range of well-fitting MT solutions can be found, spanning from a dominant positive isotropic term to a dominant negative vertical compensated linear vector dipole. The true mechanism can be discriminated by additionally modeling first-motion polarities at seismic arrays at teleseismic distances. A comparative assessment of the 2016 explosion with earlier nuclear tests documents similar vertical waveforms but a significant increase of amplitude for the 2016 explosions, which proves that the 9 September 2016 was the largest nuclear explosion ever performed in North Korea with a magnitude Mw 4.9 and a shallow depth of less than 2 km, although there are no proofs of a fusion explosion. Modeling transversal component waveforms suggests variable size and orientation of the double-couple components of the 2009, 2013, and 2016 sources.}, language = {en} } @article{NooshiriSaulHeimannetal.2017, author = {Nooshiri, Nima and Saul, Joachim and Heimann, Sebastian and Tilmann, Frederik and Dahm, Torsten}, title = {Revision of earthquake hypocentre locations in global bulletin data sets using source-specific station terms}, series = {Geophysical journal international}, volume = {208}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggw405}, pages = {589 -- 602}, year = {2017}, abstract = {Global earthquake locations are often associated with very large systematic travel-time residuals even for clear arrivals, especially for regional and near-regional stations in subduction zones because of their strongly heterogeneous velocity structure. Travel-time corrections can drastically reduce travel-time residuals at regional stations and, in consequence, improve the relative location accuracy. We have extended the shrinking-box source-specific station terms technique to regional and teleseismic distances and adopted the algorithm for probabilistic, nonlinear, global-search location. We evaluated the potential of the method to compute precise relative hypocentre locations on a global scale. The method has been applied to two specific test regions using existing P- and pP-phase picks. The first data set consists of 3103 events along the Chilean margin and the second one comprises 1680 earthquakes in the Tonga-Fiji subduction zone. Pick data were obtained from the GEOFON earthquake bulletin, produced using data from all available, global station networks. A set of timing corrections varying as a function of source position was calculated for each seismic station. In this way, we could correct the systematic errors introduced into the locations by the inaccuracies in the assumed velocity structure without explicitly solving for a velocity model. Residual statistics show that the median absolute deviation of the travel-time residuals is reduced by 40-60 per cent at regional distances, where the velocity anomalies are strong. Moreover, the spread of the travel-time residuals decreased by similar to 20 per cent at teleseismic distances (>28 degrees). Furthermore, strong variations in initial residuals as a function of recording distance are smoothed out in the final residuals. The relocated catalogues exhibit less scattered locations in depth and sharper images of the seismicity associated with the subducting slabs. Comparison with a high-resolution local catalogue reveals that our relocation process significantly improves the hypocentre locations compared to standard locations.}, language = {en} } @article{DahmHeimannFunkeetal.2018, author = {Dahm, Torsten and Heimann, Sebastian and Funke, Sigward and Wendt, Siegfried and Rappsilber, Ivo and Bindi, Dino and Plenefisch, Thomas and Cotton, Fabrice Pierre}, title = {Seismicity in the block mountains between Halle and Leipzig, Central Germany}, series = {Journal of seismology}, volume = {22}, journal = {Journal of seismology}, number = {4}, publisher = {Springer}, address = {Dordrecht}, issn = {1383-4649}, doi = {10.1007/s10950-018-9746-9}, pages = {985 -- 1003}, year = {2018}, abstract = {On April 29, 2017 at 0:56 UTC (2:56 local time), an M (W) = 2.8 earthquake struck the metropolitan area between Leipzig and Halle, Germany, near the small town of Markranstadt. The earthquake was felt within 50 km from the epicenter and reached a local intensity of I (0) = IV. Already in 2015 and only 15 km northwest of the epicenter, a M (W) = 3.2 earthquake struck the area with a similar large felt radius and I (0) = IV. More than 1.1 million people live in the region, and the unusual occurrence of the two earthquakes led to public attention, because the tectonic activity is unclear and induced earthquakes have occurred in neighboring regions. Historical earthquakes south of Leipzig had estimated magnitudes up to M (W) ae 5 and coincide with NW-SE striking crustal basement faults. We use different seismological methods to analyze the two recent earthquakes and discuss them in the context of the known tectonic structures and historical seismicity. Novel stochastic full waveform simulation and inversion approaches are adapted for the application to weak, local earthquakes, to analyze mechanisms and ground motions and their relation to observed intensities. We find NW-SE striking normal faulting mechanisms for both earthquakes and centroid depths of 26 and 29 km. The earthquakes are located where faults with large vertical offsets of several hundred meters and Hercynian strike have developed since the Mesozoic. We use a stochastic full waveform simulation to explain the local peak ground velocities and calibrate the method to simulate intensities. Since the area is densely populated and has sensitive infrastructure, we simulate scenarios assuming that a 12-km long fault segment between the two recent earthquakes is ruptured and study the impact of rupture parameters on ground motions and expected damage.}, language = {en} } @misc{DahmHeimannFunkeetal.2018, author = {Dahm, Torsten and Heimann, Sebastian and Funke, Sigward and Wendt, Siegfried and Rappsilber, Ivo and Bindi, Dino and Plenefisch, Thomas and Cotton, Fabrice Pierre}, title = {Correction to: Seismicity in the block mountains between Halle and Leipzig, Central Germany: centroid moment tensors, ground motion simulation, and felt intensities of two M approximate to 3 earthquakes in 2015 and 2017 (vol 22, pg 985, 2018)}, series = {Journal of seismology}, volume = {22}, journal = {Journal of seismology}, number = {6}, publisher = {Springer}, address = {Dordrecht}, issn = {1383-4649}, doi = {10.1007/s10950-018-9773-6}, pages = {1669 -- 1671}, year = {2018}, language = {en} } @article{AlHalbouniHolohanTaherietal.2019, author = {Al-Halbouni, Djamil and Holohan, Eoghan P. and Taheri, Abbas and Watson, Robert A. and Polom, Ulrich and Schoepfer, Martin P. J. and Emam, Sacha and Dahm, Torsten}, title = {Distinct element geomechanical modelling of the formation of sinkhole clusters within large-scale karstic depressions}, series = {Solid earth}, volume = {10}, journal = {Solid earth}, number = {4}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1869-9510}, doi = {10.5194/se-10-1219-2019}, pages = {1219 -- 1241}, year = {2019}, abstract = {The 2-D distinct element method (DEM) code (PFC2D_V5) is used here to simulate the evolution of subsidence-related karst landforms, such as single and clustered sinkholes, and associated larger-scale depressions. Subsurface material in the DEM model is removed progressively to produce an array of cavities; this simulates a network of subsurface groundwater conduits growing by chemical/mechanical erosion. The growth of the cavity array is coupled mechanically to the gravitationally loaded surroundings, such that cavities can grow also in part by material failure at their margins, which in the limit can produce individual collapse sinkholes. Two end-member growth scenarios of the cavity array and their impact on surface subsidence were examined in the models: (1) cavity growth at the same depth level and growth rate; (2) cavity growth at progressively deepening levels with varying growth rates. These growth scenarios are characterised by differing stress patterns across the cavity array and its overburden, which are in turn an important factor for the formation of sinkholes and uvalalike depressions. For growth scenario (1), a stable compression arch is established around the entire cavity array, hindering sinkhole collapse into individual cavities and favouring block-wise, relatively even subsidence across the whole cavity array. In contrast, for growth scenario (2), the stress system is more heterogeneous, such that local stress concentrations exist around individual cavities, leading to stress interactions and local wall/overburden fractures. Consequently, sinkhole collapses occur in individual cavities, which results in uneven, differential subsidence within a larger-scale depression. Depending on material properties of the cavity-hosting material and the overburden, the larger-scale depression forms either by sinkhole coalescence or by widespread subsidence linked geometrically to the entire cavity array. The results from models with growth scenario (2) are in close agreement with surface morphological and subsurface geophysical observations from an evaporite karst area on the eastern shore of the Dead Sea.}, language = {en} } @article{KaramzadehKuehnKriegerowskietal.2019, author = {Karamzadeh, Nasim Toularoud and K{\"u}hn, Daniela and Kriegerowski, Marius and L{\´o}pez-Comino, Jos{\´e} {\´A}ngel and Cesca, Simone and Dahm, Torsten}, title = {Small-aperture array as a tool to monitor fluid injection- and extraction-induced microseismicity}, series = {Acta Geophysica}, volume = {67}, journal = {Acta Geophysica}, number = {1}, publisher = {Springer}, address = {Cham}, issn = {1895-6572}, doi = {10.1007/s11600-018-0231-1}, pages = {311 -- 326}, year = {2019}, abstract = {The monitoring of microseismicity during temporary human activities such as fluid injections for hydrofracturing, hydrothermal stimulations or wastewater disposal is a difficult task. The seismic stations often cannot be installed on hard rock, and at quiet places, noise is strongly increased during the operation itself and the installation of sensors in deep wells is costly and often not feasible. The combination of small-aperture seismic arrays with shallow borehole sensors offers a solution. We tested this monitoring approach at two different sites: (1) accompanying a fracking experiment in sedimentary shale at 4km depth and (2) above a gas field under depletion. The small-aperture arrays were planned according to theoretical wavenumber studies combined with simulations considering the local noise conditions. We compared array recordings with recordings available from shallow borehole sensors and give examples of detection and location performance. Although the high-frequency noise on the 50-m-deep borehole sensors was smaller compared to the surface noise before the injection experiment, the signals were highly contaminated during injection by the pumping activities. Therefore, a set of three small-aperture arrays at different azimuths was more suited to detect small events, since noise recorded on these arrays is uncorrelated with each other. Further, we developed recommendations for the adaptation of the monitoring concept to other sites experiencing induced seismicity.}, language = {en} } @article{HeimannVasyuraBathkeSudhausetal.2019, author = {Heimann, Sebastian and Vasyura-Bathke, Hannes and Sudhaus, Henriette and Isken, Marius Paul and Kriegerowski, Marius and Steinberg, Andreas and Dahm, Torsten}, title = {A Python framework for efficient use of pre-computed Green's functions in seismological and other physical forward and inverse source problems}, series = {Solid earth}, volume = {10}, journal = {Solid earth}, number = {6}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1869-9510}, doi = {10.5194/se-10-1921-2019}, pages = {1921 -- 1935}, year = {2019}, abstract = {The computation of such synthetic GFs is computationally and operationally demanding. As a consequence, the onthe-fly recalculation of synthetic GFs in each iteration of an optimisation is time-consuming and impractical. Therefore, the pre-calculation and efficient storage of synthetic GFs on a dense grid of source to receiver combinations enables the efficient lookup and utilisation of GFs in time-critical scenarios. We present a Python-based framework and toolkit - Pyrocko-GF - that enables the pre-calculation of synthetic GF stores, which are independent of their numerical calculation method and GF transfer function. The framework aids in the creation of such GF stores by interfacing a suite of established numerical forward modelling codes in seismology (computational back ends). So far, interfaces to back ends for layered Earth model cases have been provided; however, the architecture of Pyrocko-GF is designed to cover back ends for other geometries (e.g. full 3-D heterogeneous media) and other physical quantities (e.g. gravity, pressure, tilt). Therefore, Pyrocko-GF defines an extensible GF storage format suitable for a wide range of GF types, especially handling elasticity and wave propagation problems. The framework assists with visualisations, quality control, and the exchange of GF stores, which is supported through an online platform that provides many pre-calculated GF stores for local, regional, and global studies. The Pyrocko-GF toolkit comes with a well-documented application programming interface (API) for the Python programming language to efficiently facilitate forward modelling of geophysical processes, e.g. synthetic waveforms or static displacements for a wide range of source models.}, language = {en} } @article{DahmKuehnOhrnbergeretal.2010, author = {Dahm, Torsten and Kuehn, Daniela and Ohrnberger, Matthias and Kroeger, Jens and Wiederhold, Helga and Reuther, Claus-Dieter and Dehghani, Ali and Scherbaum, Frank}, title = {Combining geophysical data sets to study the dynamics of shallow evaporites in urban environments : application to Hamburg, Germany}, issn = {0956-540X}, doi = {10.1111/j.1365-246X.2010.04521.x}, year = {2010}, abstract = {Shallowly situated evaporites in built-up areas are of relevance for urban and cultural development and hydrological regulation. The hazard of sinkholes, subrosion depressions and gypsum karst is often difficult to evaluate and may quickly change with anthropogenic influence. The geophysical exploration of evaporites in metropolitan areas is often not feasible with active industrial techniques. We collect and combine different passive geophysical data as microgravity, ambient vibrations, deformation and hydrological information to study the roof morphology of shallow evaporites beneath Hamburg, Northern Germany. The application of a novel gravity inversion technique leads to a 3-D depth model of the salt diapir under study. We compare the gravity-based depth model to pseudo-depths from H/V measurements and depth estimates from small-scale seismological array data. While the general range and trend of the diapir roof is consistent, a few anomalous regions are identified where H/V pseudo-depths indicate shallower structures not observed in gravity or array data. These are interpreted by shallow residual caprock floaters and zones of increased porosity. The shallow salt structure clearly correlates with a relative subsidence in the order of 2 mm yr(-1). The combined interpretation of roof morphology, yearly subsidence rates, chemical analyses of groundwater and of hydraulic head in aquifers indicates that the salt diapir beneath Hamburg is subject to significant ongoing dissolution that may possibly affect subrosion depressions, sinkhole distribution and land usage. The combined analysis of passive geophysical data may be exemplary for the study of shallow evaporites beneath other urban areas.}, language = {en} } @article{MaghsoudiCescaHainzletal.2013, author = {Maghsoudi, Samira and Cesca, Simone and Hainzl, Sebastian and Kaiser, Diethelm and Becker, Dirk and Dahm, Torsten}, title = {Improving the estimation of detection probability and magnitude of completeness in strongly heterogeneous media, an application to acoustic emission (AE)}, series = {Geophysical journal international}, volume = {193}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt049}, pages = {1556 -- 1569}, year = {2013}, abstract = {Reliable estimations of magnitude of completeness (M-c) are essential for a correct interpretation of seismic catalogues. The spatial distribution of M-c may be strongly variable and difficult to assess in mining environments, owing to the presence of galleries, cavities, fractured regions, porous media and different mineralogical bodies, as well as in consequence of inhomogeneous spatial distribution of the seismicity. We apply a 3-D modification of the probabilistic magnitude of completeness (PMC) method, which relies on the analysis of network detection capabilities. In our approach, the probability to detect an event depends on its magnitude, source receiver Euclidian distance and source receiver direction. The suggested method is proposed for study of the spatial distribution of the magnitude of completeness in a mining environment and here is applied to a 2-months acoustic emission (AE) data set recorded at the Morsleben salt mine, Germany. The dense seismic network and the large data set, which includes more than one million events, enable a detailed testing of the method. This method is proposed specifically for strongly heterogeneous media. Besides, it can also be used for specific network installations, with sensors with a sensitivity, dependent on the direction of the incoming wave (e.g. some piezoelectric sensors). In absence of strong heterogeneities, the standards PMC approach should be used. We show that the PMC estimations in mines strongly depend on the source receiver direction, and cannot be correctly accounted using a standard PMC approach. However, results can be improved, when adopting the proposed 3-D modification of the PMC method. Our analysis of one central horizontal and vertical section yields a magnitude of completeness of about M-c approximate to 1 (AE magnitude) at the centre of the network, which increases up to M-c approximate to 4 at further distances outside the network; the best detection performance is estimated for a NNE-SSE elongated region, which corresponds to the strike direction of the low-attenuating salt body. Our approach provides us with small-scale details about the capability of sensors to detect an earthquake, which can be linked to the presence of heterogeneities in specific directions. Reduced detection performance in presence of strong structural heterogeneities (cavities) is confirmed by synthetic waveform modelling in heterogeneous media.}, language = {en} } @article{CescaBraunMaccaferrietal.2013, author = {Cesca, Simone and Braun, Thomas and Maccaferri, Francesco and Passarelli, Luigi and Rivalta, Eleonora and Dahm, Torsten}, title = {Source modelling of the M5-6 Emilia-Romagna, Italy, earthquakes (2012 May 20-29)}, series = {Geophysical journal international}, volume = {193}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt069}, pages = {1658 -- 1672}, year = {2013}, abstract = {On 2012 May 20 and 29, two damaging earthquakes with magnitudes M-w 6.1 and 5.9, respectively, struck the Emilia-Romagna region in the sedimentary Po Plain, Northern Italy, causing 26 fatalities, significant damage to historical buildings and substantial impact to the economy of the region. The earthquake sequence included four more aftershocks with M-w, >= 5.0, all at shallow depths (about 7-9 km), with similar WNW-ESE striking reverse mechanism. The timeline of the sequence suggests significant static stress interaction between the largest events. We perform here a detailed source inversion, first adopting a point source approximation and considering pure double couple and full moment tensor source models. We compare different extended source inversion approaches for the two largest events, and find that the rupture occurred in both cases along a subhorizontal plane, dipping towards SSW Directivity is well detected for the May 20 main shock, indicating that the rupture propagated unilaterally towards SE. Based on the focal mechanism solution, we further estimate the co-seismic static stress change induced by the May 20 event. By using the rate-and-state model and a Poissonian earthquake occurrence, we infer that the second largest event of May 29 was induced with a probability in the range 0.2-0.4. This suggests that the segment of fault was already prone to rupture. Finally, we estimate peak ground accelerations for the two main events as occurred separately or simultaneously. For the scenario involving hypothetical rupture areas of both main events, we estimate M-w = 6.3 and an increase of ground acceleration by 50 per cent. The approach we propose may help to quantify rapidly which regions are invested by a significant increase of the hazard, bearing the potential for large aftershocks or even a second main shock.}, language = {en} } @article{SenCescaBischoffetal.2013, author = {Sen, Ali Tolga and Cesca, Simone and Bischoff, Monika and Meier, Thomas and Dahm, Torsten}, title = {Automated full moment tensor inversion of coal mining-induced seismicity}, series = {Geophysical journal international}, volume = {195}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt300}, pages = {1267 -- 1281}, year = {2013}, abstract = {Seismicity induced by coal mining in the Ruhr region, Germany, has been monitored continuously over the last 25 yr. In 2006, a dense temporary network (HAMNET) was deployed to locally monitor seismicity induced by longwall mining close to the town of Hamm. Between 2006 July and 2007 July, more than 7000 events with magnitudes M-L from -1.7 to 2.0 were detected. The spatiotemporal distribution of seismicity shows high correlation with the mining activity. In order to monitor rupture processes, we set up an automated source inversion routine and successfully perform double couple and full moment tensor (MT) inversions for more than 1000 events with magnitudes above M-L -0.5. The source inversion is based on a full waveform approach, both in the frequency and in the time domain, providing information about the centroid location, focal mechanism, scalar moment and full MT. Inversion results indicate a strong dominance of normal faulting focal mechanisms, with a steeper plane and a subhorizontal one. Fault planes are oriented parallel to the mining stopes. We classify the focal mechanisms based on their orientation and observe different frequency-magnitude distributions for families of events with different focal mechanisms; the overall frequency-magnitude distribution is not fitting the Gutenberg-Richter relation. Full MTs indicate that non-negligible opening tensile components accompanied normal faulting source mechanisms. Finally, extended source models are investigated for largest events. Results suggest that the rupture processes mostly occurred along the subvertical planes.}, language = {en} } @article{HeimannGonzalezWangetal.2013, author = {Heimann, Sebastian and Gonzalez, Alvaro and Wang, Rongjiang and Cesca, Simone and Dahm, Torsten}, title = {Seismic characterization of the Chelyabinsk Meteor's terminal explosion}, series = {Seismological research letters}, volume = {84}, journal = {Seismological research letters}, number = {6}, publisher = {Seismological Society of America}, address = {Albany}, issn = {0895-0695}, doi = {10.1785/0220130042}, pages = {1021 -- 1025}, year = {2013}, language = {en} } @article{KuhnOhrnbergerDahm2011, author = {Kuhn, Daniela and Ohrnberger, Matthias and Dahm, Torsten}, title = {Imaging a shallow salt diapir using ambient seismic vibrations beneath the densely built-up city area of Hamburg, Northern Germany}, series = {Journal of seismology}, volume = {15}, journal = {Journal of seismology}, number = {3}, publisher = {Springer}, address = {Dordrecht}, issn = {1383-4649}, doi = {10.1007/s10950-011-9234-y}, pages = {507 -- 531}, year = {2011}, abstract = {Salt diapirs are common features of sedimentary basins. If close to the surface, they can bear a significant hazard due to possible dissolution sinkholes, karst formation and collapse dolines or their influence on ground water chemistry. We investigate the potential of ambient vibration techniques to map the 3-D roof morphology of shallow salt diapirs. Horizontal-to-vertical (H/V) spectral peaks are derived at more than 900 positions above a shallow diapir beneath the city area of Hamburg, Germany, and are used to infer the depth of the first strong impedance contrast. In addition, 15 small-scale array measurements are conducted at different positions in order to compute frequency-dependent phase velocities of Rayleigh waves between 0.5 and 25 Hz. The dispersion curves are inverted together with the H/V peak frequency to obtain shear-wave velocity profiles. Additionally, we compare the morphology derived from H/V and array measurements to borehole lithology and a gravity-based 3-D model of the salt diapir. Both methods give consistent results in agreement with major features indicated by the independent data. An important result is that H/V and array measurements are better suited to identify weathered gypsum caprocks or gypsum floaters, while gravity-derived models better sample the interface between sediments and homogeneous salt. We further investigate qualitatively the influence of the 3-D subsurface topography of the salt diapir on the validity of local 1-D inversion results from ambient vibration dispersion curve inversion.}, language = {en} } @article{DahmFischer2014, author = {Dahm, Torsten and Fischer, Tomas}, title = {Velocity ratio variations in the source region of earthquake swarms in NW Bohemia obtained from arrival time double-differences}, series = {Geophysical journal international}, volume = {196}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt410}, pages = {957 -- 970}, year = {2014}, abstract = {Crustal earthquake swarms are an expression of intensive cracking and rock damaging over periods of days, weeks or month in a small source region in the crust. They are caused by longer lasting stress changes in the source region. Often, the localized stressing of the crust is associated with fluid or gas migration, possibly in combination with pre-existing zones of weaknesses. However, verifying and quantifying localized fluid movement at depth remains difficult since the area affected is small and geophysical prospecting methods often cannot reach the required resolution. We apply a simple and robust method to estimate the velocity ratio between compressional (P) and shear (S) waves (upsilon(P)/upsilon(S)-ratio) in the source region of an earthquake swarm. The upsilon(P)/upsilon(S)-ratio may be unusual small if the swarm is related to gas in a porous or fractured rock. The method uses arrival time difference between P and S waves observed at surface seismic stations, and the associated double differences between pairs of earthquakes. An advantage is that earthquake locations are not required and the method seems lesser dependent on unknown velocity variations in the crust outside the source region. It is, thus, suited for monitoring purposes. Applications comprise three natural, mid-crustal (8-10 km) earthquake swarms between 1997 and 2008 from the NW-Bohemia swarm region. We resolve a strong temporal decrease of upsilon(P)/upsilon(S) before and during the main activity of the swarm, and a recovery of upsilon(P)/upsilon(S) to background levels at the end of the swarms. The anomalies are interpreted in terms of the Biot-Gassman equations, assuming the presence of oversaturated fluids degassing during the beginning phase of the swarm activity.}, language = {en} } @article{MaghsoudiHainzlCescaetal.2014, author = {Maghsoudi, Samira and Hainzl, Sebastian and Cesca, Simone and Dahm, Torsten and Kaiser, Diethelm}, title = {Identification and characterization of growing large-scale en-echelon fractures in a salt mine}, series = {Geophysical journal international}, volume = {196}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt443}, pages = {1092 -- 1105}, year = {2014}, abstract = {The spatiotemporal seismicity of acoustic emission (AE) events recorded in the Morsleben salt mine is investigated. Almost a year after backfilling of the cavities from 2003, microevents are distributed with distinctive stripe shapes above cavities at different depth levels. The physical forces driving the creation of these stripes are still unknown. This study aims to find the active stripes and track fracture developments over time by combining two different temporal and spatial clustering techniques into a single methodological approach. Anomalous seismicity parameters values like sharp b-value changes for two active stripes are good indicators to explain possible stress accumulation at the stripe tips. We identify the formation of two new seismicity stripes and show that the AE activities in active clusters are migrated mostly unidirectional to eastward and upward. This indicates that the growth of underlying macrofractures is controlled by the gradient of extensional stress. Studying size distribution characteristic in terms of frequency-magnitude distribution and b-value in active phase and phase with constant seismicity rate show that deviations from the Gutenberg-Richter power law can be explained by the inclusion of different activity phases: (1) the inactive period before the formation of macrofractures, which is characterized by a deficit of larger events (higher b-values) and (2) the period of fracture growth characterized by the occurrence of larger events (smaller b-values).}, language = {en} } @article{PassarelliHainzlCescaetal.2015, author = {Passarelli, Luigi and Hainzl, Sebastian and Cesca, Simone and Maccaferri, Francesco and Mucciarelli, Marco and R{\"o}ßler, Dirk and Corbi, Fabio and Dahm, Torsten and Rivalta, Eleonora}, title = {Aseismic transient driving the swarm-like seismic sequence in the Pollino range, Southern Italy}, series = {Geophysical journal international}, volume = {201}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggv111}, pages = {1553 -- 1567}, year = {2015}, abstract = {Tectonic earthquake swarms challenge our understanding of earthquake processes since it is difficult to link observations to the underlying physical mechanisms and to assess the hazard they pose. Transient forcing is thought to initiate and drive the spatio-temporal release of energy during swarms. The nature of the transient forcing may vary across sequences and range from aseismic creeping or transient slip to diffusion of pore pressure pulses to fluid redistribution and migration within the seismogenic crust. Distinguishing between such forcing mechanisms may be critical to reduce epistemic uncertainties in the assessment of hazard due to seismic swarms, because it can provide information on the frequency-magnitude distribution of the earthquakes (often deviating from the assumed Gutenberg-Richter relation) and on the expected source parameters influencing the ground motion (for example the stress drop). Here we study the ongoing Pollino range (Southern Italy) seismic swarm, a long-lasting seismic sequence with more than five thousand events recorded and located since October 2010. The two largest shocks (magnitude M-w = 4.2 and M-w = 5.1) are among the largest earthquakes ever recorded in an area which represents a seismic gap in the Italian historical earthquake catalogue. We investigate the geometrical, mechanical and statistical characteristics of the largest earthquakes and of the entire swarm. We calculate the focal mechanisms of the M-l > 3 events in the sequence and the transfer of Coulomb stress on nearby known faults and analyse the statistics of the earthquake catalogue. We find that only 25 per cent of the earthquakes in the sequence can be explained as aftershocks, and the remaining 75 per cent may be attributed to a transient forcing. The b-values change in time throughout the sequence, with low b-values correlated with the period of highest rate of activity and with the occurrence of the largest shock. In the light of recent studies on the palaeoseismic and historical activity in the Pollino area, we identify two scenarios consistent with the observations and our analysis: This and past seismic swarms may have been 'passive' features, with small fault patches failing on largely locked faults, or may have been accompanied by an 'active', largely aseismic, release of a large portion of the accumulated tectonic strain. Those scenarios have very different implications for the seismic hazard of the area.}, language = {en} } @article{MaghsoudiCescaHainzletal.2015, author = {Maghsoudi, Samira and Cesca, Simone and Hainzl, Sebastian and Dahm, Torsten and Z{\"o}ller, Gert and Kaiser, Diethelm}, title = {Maximum Magnitude of Completeness in a Salt Mine}, series = {Bulletin of the Seismological Society of America}, volume = {105}, journal = {Bulletin of the Seismological Society of America}, number = {3}, publisher = {Seismological Society of America}, address = {Albany}, issn = {0037-1106}, doi = {10.1785/0120140039}, pages = {1491 -- 1501}, year = {2015}, abstract = {In this study, we analyze acoustic emission (AE) data recorded at the Morsleben salt mine, Germany, to assess the catalog completeness, which plays an important role in any seismicity analysis. We introduce the new concept of a magnitude completeness interval consisting of a maximum magnitude of completeness (M-c(max)) in addition to the well-known minimum magnitude of completeness. This is required to describe the completeness of the catalog, both for the smallest events (for which the detection performance may be low) and for the largest ones (which may be missed because of sensors saturation). We suggest a method to compute the maximum magnitude of completeness and calculate it for a spatial grid based on (1) the prior estimation of saturation magnitude at each sensor, (2) the correction of the detection probability function at each sensor, including a drop in the detection performance when it saturates, and (3) the combination of detection probabilities of all sensors to obtain the network detection performance. The method is tested using about 130,000 AE events recorded in a period of five weeks, with sources confined within a small depth interval, and an example of the spatial distribution of M-c(max) is derived. The comparison between the spatial distribution of M-c(max) and of the maximum possible magnitude (M-max), which is here derived using a recently introduced Bayesian approach, indicates that M-max exceeds M-c(max) in some parts of the mine. This suggests that some large and important events may be missed in the catalog, which could lead to a bias in the hazard evaluation.}, language = {en} } @article{CescaSenDahm2014, author = {Cesca, Simone and Sen, Ali Tolga and Dahm, Torsten}, title = {Seismicity monitoring by cluster analysis of moment tensors}, series = {Geophysical journal international}, volume = {196}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt492}, pages = {1813 -- 1826}, year = {2014}, abstract = {We suggest a new clustering approach to classify focal mechanisms from large moment tensor catalogues, with the purpose of automatically identify families of earthquakes with similar source geometry, recognize the orientation of most active faults, and detect temporal variations of the rupture processes. The approach differs in comparison to waveform similarity methods since clusters are detected even if they occur in large spatial distances. This approach is particularly helpful to analyse large moment tensor catalogues, as in microseismicity applications, where a manual analysis and classification is not feasible. A flexible algorithm is here proposed: it can handle different metrics, norms, and focal mechanism representations. In particular, the method can handle full moment tensor or constrained source model catalogues, for which different metrics are suggested. The method can account for variable uncertainties of different moment tensor components. We verify the method with synthetic catalogues. An application to real data from mining induced seismicity illustrates possible applications of the method and demonstrate the cluster detection and event classification performance with different moment tensor catalogues. Results proof that main earthquake source types occur on spatially separated faults, and that temporal changes in the number and characterization of focal mechanism clusters are detected. We suggest that moment tensor clustering can help assessing time dependent hazard in mines.}, language = {en} } @misc{DahmBeckerBischoffetal.2013, author = {Dahm, Torsten and Becker, Dirk and Bischoff, Monika and Cesca, Simone and Dost, B. and Fritschen, R. and Hainzl, Sebastian and Klose, C. D. and Kuhn, D. and Lasocki, S. and Meier, Thomas and Ohrnberger, Matthias and Rivalta, Eleonora and Wegler, Ulrich and Husen, Stephan}, title = {Recommendation for the discrimination of human-related and natural seismicity}, series = {Journal of seismology}, volume = {17}, journal = {Journal of seismology}, number = {1}, publisher = {Springer}, address = {Dordrecht}, issn = {1383-4649}, doi = {10.1007/s10950-012-9295-6}, pages = {197 -- 202}, year = {2013}, abstract = {Various techniques are utilized by the seismological community, extractive industries, energy and geoengineering companies to identify earthquake nucleation processes in close proximity to engineering operation points. These operations may comprise fluid extraction or injections, artificial water reservoir impoundments, open pit and deep mining, deep geothermal power generations or carbon sequestration. In this letter to the editor, we outline several lines of investigation that we suggest to follow to address the discrimination problem between natural seismicity and seismic events induced or triggered by geoengineering activities. These suggestions have been developed by a group of experts during several meetings and workshops, and we feel that their publication as a summary report is helpful for the geoscientific community. Specific investigation procedures and discrimination approaches, on which our recommendations are based, are also published in this Special Issue (SI) of Journal of Seismology.}, language = {en} } @article{KottmeierAgnonAlHalbounietal.2016, author = {Kottmeier, Christoph and Agnon, Amotz and Al-Halbouni, Djamil and Alpert, Pinhas and Corsmeier, Ulrich and Dahm, Torsten and Eshel, Adam and Geyer, Stefan and Haas, Michael and Holohan, Eoghan and Kalthoff, Norbert and Kishcha, Pavel and Krawczyk, Charlotte and Lati, Joseph and Laronne, Jonathan B. and Lott, Friederike and Mallast, Ulf and Merz, Ralf and Metzger, Jutta and Mohsen, Ayman and Morin, Efrat and Nied, Manuela and Roediger, Tino and Salameh, Elias and Sawarieh, Ali and Shannak, Benbella and Siebert, Christian and Weber, Michael}, title = {New perspectives on interdisciplinary earth science at the Dead Sea: The DESERVE project}, series = {The science of the total environment : an international journal for scientific research into the environment and its relationship with man}, volume = {544}, journal = {The science of the total environment : an international journal for scientific research into the environment and its relationship with man}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0048-9697}, doi = {10.1016/j.scitotenv.2015.12.003}, pages = {1045 -- 1058}, year = {2016}, abstract = {The Dead Sea region has faced substantial environmental challenges in recent decades, including water resource scarcity, similar to 1 m annual decreases in the water level, sinkhole development, ascending-brine freshwater pollution, and seismic disturbance risks. Natural processes are significantly affected by human interference as well as by climate change and tectonic developments over the long term. To get a deep understanding of processes and their interactions, innovative scientific approaches that integrate disciplinary research and education are required. The research project DESERVE (Helmholtz Virtual Institute Dead Sea Research Venue) addresses these challenges in an interdisciplinary approach that includes geophysics, hydrology, and meteorology. The project is implemented by a consortium of scientific institutions in neighboring countries of the Dead Sea (Israel, Jordan, Palestine Territories) and participating German Helmholtz Centres (KIT, GFZ, UFZ). A new monitoring network of meteorological, hydrological, and seismic/geodynamic stations has been established, and extensive field research and numerical simulations have been undertaken. For the first time, innovative measurement and modeling techniques have been applied to the extreme conditions of the Dead Sea and its surroundings. The preliminary results show the potential of these methods. First time ever performed eddy covariance measurements give insight into the governing factors of Dead Sea evaporation. High-resolution bathymetric investigations reveal a strong correlation between submarine springs and neo-tectonic patterns. Based on detailed studies of stratigraphy and borehole information, the extension of the subsurface drainage basin of the Dead Sea is now reliably estimated. Originality has been achieved in monitoring flash floods in an arid basin at its outlet and simultaneously in tributaries, supplemented by spatio-temporal rainfall data. Low-altitude, high resolution photogrammetry, allied to satellite image analysis and to geophysical surveys (e.g. shear-wave reflections) has enabled a more detailed characterization of sinkhole morphology and temporal development and the possible subsurface controls thereon. All the above listed efforts and scientific results take place with the interdisciplinary education of young scientists. They are invited to attend joint thematic workshops and winter schools as well as to participate in field experiments. (C) 2015 The Authors. Published by Elsevier B.V.}, language = {en} } @misc{PassarelliHainzlCescaetal.2016, author = {Passarelli, Luigi and Hainzl, Sebastian and Cesca, Simone and Maccaferri, Francesco and Mucciarelli, Marco and Roessler, Dirk and Corbi, Fabio and Dahm, Torsten and Rivalta, Eleonora}, title = {Aseismic transient driving the swarm-like seismic sequence in the Pollino range, Southern Italy (vol 201, pg 1553, 2015)}, series = {Geophysical journal international}, volume = {204}, journal = {Geophysical journal international}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggv425}, pages = {365 -- 365}, year = {2016}, language = {en} } @article{GrigoliCescaRinaldietal.2018, author = {Grigoli, Francesco and Cesca, Simone and Rinaldi, Antonio Pio and Manconi, Andrea and Lopez-Comino, Jos{\´e} {\´A}ngel and Clinton, John F. and Westaway, Rob and Cauzzi, Carlo and Dahm, Torsten and Wiemer, Stefan}, title = {The November 2017 M-w 5.5 Pohang earthquake}, series = {Science}, volume = {360}, journal = {Science}, number = {6392}, publisher = {American Assoc. for the Advancement of Science}, address = {Washington}, issn = {0036-8075}, doi = {10.1126/science.aat2010}, pages = {1003 -- 1006}, year = {2018}, abstract = {The moment magnitude (M-w) 5.5 earthquake that struck South Korea in November 2017 was one of the largest and most damaging events in that country over the past century. Its proximity to an enhanced geothermal system site, where high-pressure hydraulic injection had been performed during the previous 2 years, raises the possibility that this earthquake was anthropogenic. We have combined seismological and geodetic analyses to characterize the mainshock and its largest aftershocks, constrain the geometry of this seismic sequence, and shed light on its causal factors. According to our analysis, it seems plausible that the occurrence of this earthquake was influenced by the aforementioned industrial activities. Finally, we found that the earthquake transferred static stress to larger nearby faults, potentially increasing the seismic hazard in the area.}, language = {en} } @article{CescaGrigoliHeimannetal.2016, author = {Cesca, Simone and Grigoli, Francesco and Heimann, Sebastian and Dahm, Torsten and Kriegerowski, Marius and Sobiesiak, M. and Tassara, C. and Olcay, M.}, title = {The M-w 8.1 2014 Iquique, Chile, seismic sequence: a tale of foreshocks and aftershocks}, series = {Geophysical journal international}, volume = {204}, journal = {Geophysical journal international}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggv544}, pages = {1766 -- 1780}, year = {2016}, abstract = {The 2014 April 1, M-w 8.1 Iquique (Chile) earthquake struck in the Northern Chile seismic gap. With a rupture length of less than 200 km, it left unbroken large segments of the former gap. Early studies were able to model the main rupture features but results are ambiguous with respect to the role of aseismic slip and left open questions on the remaining hazard at the Northern Chile gap. A striking observation of the 2014 earthquake has been its extensive preparation phase, with more than 1300 events with magnitude above M-L 3, occurring during the 15 months preceding the main shock. Increasing seismicity rates and observed peak magnitudes accompanied the last three weeks before the main shock. Thanks to the large data sets of regional recordings, we assess the precursor activity, compare foreshocks and aftershocks and model rupture preparation and rupture effects. To tackle inversion challenges for moderate events with an asymmetric network geometry, we use full waveforms techniques to locate events, map the seismicity rate and derive source parameters, obtaining moment tensors for more than 300 events (magnitudes M-w 4.0-8.1) in the period 2013 January 1-2014 April 30. This unique data set of fore- and aftershocks is investigated to distinguish rupture process models and models of strain and stress rotation during an earthquake. Results indicate that the spatial distributions of foreshocks delineated the shallower part of the rupture areas of the main shock and its largest aftershock, well matching the spatial extension of the aftershocks cloud. Most moment tensors correspond to almost pure double couple thrust mechanisms, consistent with the slab orientation. Whereas no significant differences are observed among thrust mechanisms in different areas, nor among thrust foreshocks and aftershocks, the early aftershock sequence is characterized by the presence of normal fault mechanisms, striking parallel to the trench but dipping westward. These events likely occurred in the shallow wedge structure close to the slab interface and are consequence of the increased extensional stress in this region after the largest events. The overall stress inversion result suggests a minor stress rotation after the main shock, but a significant release of the deviatoric stress. The temporal change in the distribution of focal mechanisms can also be explained in terms of the spatial heterogeneity of the stress field: under such interpretation, the potential of a large megathrust earthquake breaking a larger segment offshore Northern Chile remains high.}, language = {en} } @article{CescaGrigoliHeimannetal.2014, author = {Cesca, Simone and Grigoli, Francesco and Heimann, Sebastian and Gonzalez, Alvaro and Buforn, Elisa and Maghsoudi, Samira and Blanch, Estefania and Dahm, Torsten}, title = {The 2013 September-October seismic sequence offshore Spain: a case of seismicity triggered by gas injection?}, series = {Geophysical journal international}, volume = {198}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggu172}, pages = {941 -- 953}, year = {2014}, abstract = {A spatially localized seismic sequence originated few tens of kilometres offshore the Mediterranean coast of Spain, close to the Ebro river delta, starting on 2013 September 5, and lasting at least until 2013 October. The sequence culminated in a maximal moment magnitude M-w 4.3 earthquake, on 2013 October 1. The most relevant seismogenic feature in the area is the Fosa de Amposta fault system, which includes different strands mapped at different distances to the coast, with a general NE-SW orientation, roughly parallel to the coastline. However, no significant known historical seismicity has involved this fault system in the past. The epicentral region is also located near the offshore platform of the Castor project, where gas is conducted through a pipeline from mainland and where it was recently injected in a depleted oil reservoir, at about 2 km depth. We analyse the temporal evolution of the seismic sequence and use full waveform techniques to derive absolute and relative locations, estimate depths and focal mechanisms for the largest events in the sequence (with magnitude mbLg larger than 3), and compare them to a previous event (2012 April 8, mbLg 3.3) taking place in the same region prior to the gas injection. Moment tensor inversion results show that the overall seismicity in this sequence is characterized by oblique mechanisms with a normal fault component, with a 30A degrees low-dip angle plane oriented NNE-SSW and a subvertical plane oriented NW-SE. The combined analysis of hypocentral location and focal mechanisms could indicate that the seismic sequence corresponds to rupture processes along shallow low-dip surfaces, which could have been triggered by the gas injection in the reservoir, and excludes the activation of the Amposta fault, as its known orientation is inconsistent with focal mechanism results. An alternative scenario includes the iterated triggering of a system of steep faults oriented NW-SE, which were identified by prior marine seismics investigations.}, language = {en} } @article{GrigoliCescaAmorosoetal.2014, author = {Grigoli, Francesco and Cesca, Simone and Amoroso, Ortensia and Emolo, Antonio and Zollo, Aldo and Dahm, Torsten}, title = {Automated seismic event location by waveform coherence analysis}, series = {Geophysical journal international}, volume = {196}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt477}, pages = {1742 -- 1753}, year = {2014}, abstract = {Automated location of seismic events is a very important task in microseismic monitoring operations as well for local and regional seismic monitoring. Since microseismic records are generally characterized by low signal-to-noise ratio, automated location methods are requested to be noise robust and sufficiently accurate. Most of the standard automated location routines are based on the automated picking, identification and association of the first arrivals of P and S waves and on the minimization of the residuals between theoretical and observed arrival times of the considered seismic phases. Although current methods can accurately pick P onsets, the automatic picking of the S onset is still problematic, especially when the P coda overlaps the S wave onset. In this paper, we propose a picking free earthquake location method based on the use of the short-term-average/long-term-average (STA/LTA) traces at different stations as observed data. For the P phases, we use the STA/LTA traces of the vertical energy function, whereas for the S phases, we use the STA/LTA traces of a second characteristic function, which is obtained using the principal component analysis technique. In order to locate the seismic event, we scan the space of possible hypocentral locations and origin times, and stack the STA/LTA traces along the theoretical arrival time surface for both P and S phases. Iterating this procedure on a 3-D grid, we retrieve a multidimensional matrix whose absolute maximum corresponds to the spatial coordinates of the seismic event. A pilot application was performed in the Campania-Lucania region (southern Italy) using a seismic network (Irpinia Seismic Network) with an aperture of about 150 km. We located 196 crustal earthquakes (depth < 20 km) with magnitude range 1.1 < M-L < 2.7. A subset of these locations were compared with accurate manual locations refined by using a double-difference technique. Our results indicate a good agreement with manual locations. Moreover, our method is noise robust and performs better than classical location methods based on the automatic picking of the P and S waves first arrivals.}, language = {en} } @article{ZoellerHainzlTilmannetal.2020, author = {Z{\"o}ller, Gert and Hainzl, Sebastian and Tilmann, Frederik and Woith, Heiko and Dahm, Torsten}, title = {Comment on: Wikelski, Martin; M{\"u}ller, Uschi; Scocco, Paola; Catorci, Andrea; Desinov, Lev V.; Belyaev, Mikhail Y.; Keim, Daniel A.; Pohlmeier, Winfried; Fechteler, Gerhard; Mai, Martin P. : Potential short-term earthquake forecasting by farm animal monitoring. - Ethology. - 126 (2020), 9. - S. 931 - 941. -ISSN 0179-1613. - eISSN 1439-0310. - doi 10.1111/eth.13078}, series = {Ethology}, volume = {127}, journal = {Ethology}, number = {3}, publisher = {Wiley}, address = {Hoboken}, issn = {0179-1613}, doi = {10.1111/eth.13105}, pages = {302 -- 306}, year = {2020}, abstract = {Based on an analysis of continuous monitoring of farm animal behavior in the region of the 2016 M6.6 Norcia earthquake in Italy, Wikelski et al., 2020; (Seismol Res Lett, 89, 2020, 1238) conclude that animal activity can be anticipated with subsequent seismic activity and that this finding might help to design a "short-term earthquake forecasting method." We show that this result is based on an incomplete analysis and misleading interpretations. Applying state-of-the-art methods of statistics, we demonstrate that the proposed anticipatory patterns cannot be distinguished from random patterns, and consequently, the observed anomalies in animal activity do not have any forecasting power.}, language = {en} } @article{NiemzDahmMilkereitetal.2021, author = {Niemz, Peter and Dahm, Torsten and Milkereit, Claus and Cesca, Simone and Petersen, Gesa Maria and Zang, Arno}, title = {Insights into hydraulic fracture growth gained from a joint analysis of seismometer-derived tilt signals and scoustic emissions}, series = {Journal of geophysical research : Solid earth}, volume = {126}, journal = {Journal of geophysical research : Solid earth}, number = {12}, publisher = {American Geophysical Union}, address = {Washington}, issn = {2169-9313}, doi = {10.1029/2021JB023057}, pages = {14}, year = {2021}, abstract = {Hydraulic fracturing is performed to enhance rock permeability, for example, in the frame of geothermal energy production or shale gas exploitation, and can potentially trigger induced seismicity. The tracking of increased permeabilities and the fracturing extent is often based on the microseismic event distribution within the stimulated rock volume, but it is debated whether the microseismic activity adequately depicts the fracture formation. We are able to record tilt signals that appear as long-period transients (<180 s) on two broadband seismometers installed close (17-72 m) to newly formed, meter-scale hydraulic fractures. With this observation, we can overcome the limitations of the microseismic monitoring alone and verify the fracture mapping. Our analysis for the first time combines a catalog of previously analyzed acoustic emissions ([AEs] durations of 20 ms), indirectly mapping the fractures, with unique tilt signals, that provide independent, direct insights into the deformation of the rock. The analysis allows to identify different phases of the fracturing process including the (re)opening, growth, and aftergrowth of fractures. Further, it helps to differentiate between the formation of complex fracture networks and single macrofractures, and it validates the AE fracture mapping. Our findings contribute to a better understanding of the fracturing processes, which may help to reduce fluid-injection-induced seismicity and validate efficient fracture formation.
Plain Language Summary Hydraulic fracturing (HF) describes the opening of fractures in rocks by injecting fluids under high pressure. The new fractures not only can facilitate the extraction of shale gas but can also be used to heat up water in the subsurface in enhanced geothermal systems, a corner stone of renewable energy production. The fracture formation is inherently accompanied by small, nonfelt earthquakes (microseismic events). Occasionally, larger events felt by the population can be induced by the subsurface operations. Avoiding such events is important for the acceptance of HF operations and requires a detailed knowledge about the fracture formation. We jointly analyze two very different data sets recorded during mine-scale HF experiments: (a) the tilting of the ground caused by the opening of the fractures, as recorded by broadband seismometers-usually deployed for earthquake monitoring-installed close to the experiments and (b) a catalog of acoustic emissions, seismic signals of few milliseconds emitted by tiny cracks around the forming hydraulic fracture. The novel joint analysis allows to characterize the fracturing processes in greater detail, contributing to the understanding of the physical processes, which may help to understand fluid-injection-induced seismicity and validate the formation of hydraulic fractures.}, language = {en} } @article{GrigoliCescaVassalloetal.2013, author = {Grigoli, Francesco and Cesca, Simone and Vassallo, Maurizio and Dahm, Torsten}, title = {Automated seismic event location by travel-time stacking an application to mining induced seismicity}, series = {Seismological research letters}, volume = {84}, journal = {Seismological research letters}, number = {4}, publisher = {Seismological Society of America}, address = {Albany}, issn = {0895-0695}, doi = {10.1785/0220120191}, pages = {666 -- 677}, year = {2013}, language = {en} } @article{ZieglerReiterHeidbachetal.2015, author = {Ziegler, Moritz O. and Reiter, Karsten and Heidbach, Oliver and Zang, Arno and Kwiatek, Grzegorz and Stromeyer, Dietrich and Dahm, Torsten and Dresen, Georg and Hofmann, Gerhard}, title = {Mining-Induced Stress Transfer and Its Relation to a 1.9 Seismic Event in an Ultra-deep South African Gold Mine}, series = {Pure and applied geophysics}, volume = {172}, journal = {Pure and applied geophysics}, number = {10}, publisher = {Springer}, address = {Basel}, issn = {0033-4553}, doi = {10.1007/s00024-015-1033-x}, pages = {2557 -- 2570}, year = {2015}, abstract = {On 27 December 2007, a 1.9 seismic event occurred within a dyke in the deep-level Mponeng Gold Mine, South Africa. From the seismological network of the mine and the one from the Japanese-German Underground Acoustic Emission Research in South Africa (JAGUARS) group, the hypocentral depth (3,509 m), focal mechanism and aftershock location were estimated. Since no mining activity took place in the days before the event, dynamic triggering due to blasting can be ruled out as the cause. To investigate the hypothesis that stress transfer, due to excavation of the gold reef, induced the event, we set up a small-scale high-resolution three-dimensional (3D) geomechanical numerical model. The model consisted of the four different rock units present in the mine: quartzite (footwall), hard lava (hanging wall), conglomerate (gold reef) and diorite (dykes). The numerical solution was computed using a finite-element method with a discretised mesh of approximately elements. The initial stress state of the model is in agreement with in situ data from a neighbouring mine, and the step-wise excavation was simulated by mass removal from the gold reef. The resulting 3D stress tensor and its changes due to mining were analysed based on the Coulomb failure stress changes on the fault plane of the event. The results show that the seismic event was induced regardless of how the Coulomb failure stress changes were calculated and of the uncertainties in the fault plane solution. We also used the model to assess the seismic hazard due to the excavation towards the dyke. The resulting curve of stress changes shows a significant increase in the last in front of the dyke, indicating that small changes in the mining progress towards the dyke have a substantial impact on the stress transfer.}, language = {en} } @article{RichterHainzlDahmetal.2020, author = {Richter, Gudrun and Hainzl, Sebastian and Dahm, Torsten and Z{\"o}ller, Gert}, title = {Stress-based, statistical modeling of the induced seismicity at the Groningen gas field}, series = {Environmental earth sciences}, volume = {79}, journal = {Environmental earth sciences}, number = {11}, publisher = {Springer}, address = {New York}, issn = {1866-6280}, doi = {10.1007/s12665-020-08941-4}, pages = {15}, year = {2020}, abstract = {Groningen is the largest onshore gas field under production in Europe. The pressure depletion of the gas field started in 1963. In 1991, the first induced micro-earthquakes have been located at reservoir level with increasing rates in the following decades. Most of these events are of magnitude less than 2.0 and cannot be felt. However, maximum observed magnitudes continuously increased over the years until the largest, significant event with ML=3.6 was recorded in 2014, which finally led to the decision to reduce the production. This causal sequence displays the crucial role of understanding and modeling the relation between production and induced seismicity for economic planing and hazard assessment. Here we test whether the induced seismicity related to gas exploration can be modeled by the statistical response of fault networks with rate-and-state-dependent frictional behavior. We use the long and complete local seismic catalog and additionally detailed information on production-induced changes at the reservoir level to test different seismicity models. Both the changes of the fluid pressure and of the reservoir compaction are tested as input to approximate the Coulomb stress changes. We find that the rate-and-state model with a constant tectonic background seismicity rate can reproduce the observed long delay of the seismicity onset. In contrast, so-called Coulomb failure models with instantaneous earthquake nucleation need to assume that all faults are initially far from a critical state of stress to explain the delay. Our rate-and-state model based on the fluid pore pressure fits the spatiotemporal pattern of the seismicity best, where the fit further improves by taking the fault density and orientation into account. Despite its simplicity with only three free parameters, the rate-and-state model can reproduce the main statistical features of the observed activity.}, language = {en} } @article{IskenVasyuraBathkeDahmetal.2022, author = {Isken, Marius Paul and Vasyura-Bathke, Hannes and Dahm, Torsten and Heimann, Sebastian}, title = {De-noising distributed acoustic sensing data using an adaptive frequency-wavenumber filter}, series = {Geophysical journal international}, volume = {231}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford University Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggac229}, pages = {944 -- 949}, year = {2022}, abstract = {Data recorded by distributed acoustic sensing (DAS) along an optical fibre sample the spatial and temporal properties of seismic wavefields at high spatial density. Often leading to massive amount of data when collected for seismic monitoring along many kilometre long cables. The spatially coherent signals from weak seismic arrivals within the data are often obscured by incoherent noise. We present a flexible and computationally efficient filtering technique, which makes use of the dense spatial and temporal sampling of the data and that can handle the large amount of data. The presented adaptive frequency-wavenumber filter suppresses the incoherent seismic noise while amplifying the coherent wavefield. We analyse the response of the filter in time and spectral domain, and we demonstrate its performance on a noisy data set that was recorded in a vertical borehole observatory showing active and passive seismic phase arrivals. Lastly, we present a performant open-source software implementation enabling real-time filtering of large DAS data sets.}, language = {en} } @article{FischerHrubcovaDahmetal.2022, author = {Fischer, Tom{\´a}š and Hrubcova, Pavla and Dahm, Torsten and Woith, Heiko and Vylita, Tom{\´a}š and Ohrnberger, Matthias and Vlček, Josef and Horalek, Josef and Dedecek, Petr and Zimmer, Martin and Lipus, Martin P. and Pierdominici, Simona and Kallmeyer, Jens and Kr{\"u}ger, Frank and Hannemann, Katrin and Korn, Michael and Kaempf, Horst and Reinsch, Thomas and Klicpera, Jakub and Vollmer, Daniel and Daskalopoulou, Kyriaki}, title = {ICDP drilling of the Eger Rift observatory}, series = {Scientific drilling : reports on deep earth sampling and monitoring}, volume = {31}, journal = {Scientific drilling : reports on deep earth sampling and monitoring}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1816-8957}, doi = {10.5194/sd-31-31-2022}, pages = {31 -- 49}, year = {2022}, abstract = {The new in situ geodynamic laboratory established in the framework of the ICDP Eger project aims to develop the most modern, comprehensive, multiparameter laboratory at depth for studying earthquake swarms, crustal fluid flow, mantle-derived CO2 and helium degassing, and processes of the deep biosphere. In order to reach a new level of high-frequency, near-source and multiparameter observation of earthquake swarms and related phenomena, such a laboratory comprises a set of shallow boreholes with high-frequency 3-D seismic arrays as well as modern continuous real-time fluid monitoring at depth and the study of the deep biosphere. This laboratory is located in the western part of the Eger Rift at the border of the Czech Republic and Germany (in the West Bohemia-Vogtland geodynamic region) and comprises a set of five boreholes around the seismoactive zone. To date, all monitoring boreholes have been drilled. This includes the seismic monitoring boreholes S1, S2 and S3 in the crystalline units north and east of the major Nov{\´y} Kostel seismogenic zone, borehole F3 in the Hartoušov mofette field and borehole S4 in the newly discovered Bažina maar near Lib{\´a}. Supplementary borehole P1 is being prepared in the Neualbenreuth maar for paleoclimate and biological research. At each of these sites, a borehole broadband seismometer will be installed, and sites S1, S2 and S3 will also host a 3-D seismic array composed of a vertical geophone chain and surface seismic array. Seismic instrumenting has been completed in the S1 borehole and is in preparation in the remaining four monitoring boreholes. The continuous fluid monitoring site of Hartoušov includes three boreholes, F1, F2 and F3, and a pilot monitoring phase is underway. The laboratory also enables one to analyze microbial activity at CO2 mofettes and maar structures in the context of changes in habitats. The drillings into the maar volcanoes contribute to a better understanding of the Quaternary paleoclimate and volcanic activity.}, language = {en} } @article{KruegerDahm1999, author = {Kr{\"u}ger, Frank and Dahm, Torsten}, title = {Higher degree moment inversin using far-field broad-band recordings : theory and evaluation of the method with application to the 1994 Bolivia deep earthauke}, year = {1999}, language = {en} } @article{DahmCescaHainzletal.2015, author = {Dahm, Torsten and Cesca, Simone and Hainzl, Sebastian and Braun, Thomas and Kr{\"u}ger, Frank}, title = {Discrimination between induced, triggered, and natural earthquakes close to hydrocarbon reservoirs: A probabilistic approach based on the modeling of depletion-induced stress changes and seismological source parameters}, series = {Journal of geophysical research : Solid earth}, volume = {120}, journal = {Journal of geophysical research : Solid earth}, number = {4}, publisher = {American Geophysical Union}, address = {Washington}, issn = {2169-9313}, doi = {10.1002/2014JB011778}, pages = {2491 -- 2509}, year = {2015}, abstract = {Earthquakes occurring close to hydrocarbon fields under production are often under critical view of being induced or triggered. However, clear and testable rules to discriminate the different events have rarely been developed and tested. The unresolved scientific problem may lead to lengthy public disputes with unpredictable impact on the local acceptance of the exploitation and field operations. We propose a quantitative approach to discriminate induced, triggered, and natural earthquakes, which is based on testable input parameters. Maxima of occurrence probabilities are compared for the cases under question, and a single probability of being triggered or induced is reported. The uncertainties of earthquake location and other input parameters are considered in terms of the integration over probability density functions. The probability that events have been human triggered/induced is derived from the modeling of Coulomb stress changes and a rate and state-dependent seismicity model. In our case a 3-D boundary element method has been adapted for the nuclei of strain approach to estimate the stress changes outside the reservoir, which are related to pore pressure changes in the field formation. The predicted rate of natural earthquakes is either derived from the background seismicity or, in case of rare events, from an estimate of the tectonic stress rate. Instrumentally derived seismological information on the event location, source mechanism, and the size of the rupture plane is of advantage for the method. If the rupture plane has been estimated, the discrimination between induced or only triggered events is theoretically possible if probability functions are convolved with a rupture fault filter. We apply the approach to three recent main shock events: (1) the M-w 4.3 Ekofisk 2001, North Sea, earthquake close to the Ekofisk oil field; (2) the M-w 4.4 Rotenburg 2004, Northern Germany, earthquake in the vicinity of the Sohlingen gas field; and (3) the M-w 6.1 Emilia 2012, Northern Italy, earthquake in the vicinity of a hydrocarbon reservoir. The three test cases cover the complete range of possible causes: clearly human induced, not even human triggered, and a third case in between both extremes.}, language = {en} } @article{HannemannKruegerDahm2014, author = {Hannemann, Katrin and Kr{\"u}ger, Frank and Dahm, Torsten}, title = {Measuring of clock drift rates and static time offsets of ocean bottom stations by means of ambient noise}, series = {Geophysical journal international}, volume = {196}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggt434}, pages = {1034 -- 1042}, year = {2014}, abstract = {Marine seismology usually relies on temporary deployments of stand alone seismic ocean bottom stations (OBS), which are initialized and synchronized on ship before deployment and re-synchronized and stopped on ship after recovery several months later. In between, the recorder clocks may drift and float at unknown rates. If the clock drifts are large or not linear and cannot be corrected for, seismological applications will be limited to methods not requiring precise common timing. Therefore, for example, array seismological methods, which need very accurate timing between individual stations, would not be applicable for such deployments. We use an OBS test-array of 12 stations and 75 km aperture, deployed for 10 months in the deep sea (4.5-5.5 km) of the mid-eastern Atlantic. The experiment was designed to analyse the potential of broad-band array seismology at the seafloor. After recovery, we identified some stations which either show unusual large clock drifts and/or static time offsets by having a large difference between the internal clock and the GPS-signal (skew). We test the approach of ambient noise cross-correlation to synchronize clocks of a deep water OBS array with km-scale interstation distances. We show that small drift rates and static time offsets can be resolved on vertical components with a standard technique. Larger clock drifts (several seconds per day) can only be accurately recovered if time windows of one input trace are shifted according to the expected drift between a station pair before the cross-correlation. We validate that the drifts extracted from the seismometer data are linear to first order. The same is valid for most of the hydrophones. Moreover, we were able to determine the clock drift at a station where no skew could be measured. Furthermore, we find that instable apparent drift rates at some hydrophones, which are uncorrelated to the seismometer drift recorded at the same digitizer, indicate a malfunction of the hydrophone.}, language = {en} } @article{DahmStillerMechieetal.2020, author = {Dahm, Torsten and Stiller, Manfred and Mechie, James and Heimann, Sebastian and Hensch, Martin and Woith, Heiko and Schmidt, Bernd and Gabriel, Gerald and Weber, Michael}, title = {Seismological and geophysical signatures of the deep crustal magma systems of the cenozoic volcanic fields Beneath the Eifel, Germany}, series = {Geochemistry, geophysics, geosystems}, volume = {21}, journal = {Geochemistry, geophysics, geosystems}, number = {9}, publisher = {American Geophysical Union}, address = {Washington}, issn = {1525-2027}, doi = {10.1029/2020GC009062}, pages = {21}, year = {2020}, abstract = {The Quaternary volcanic fields of the Eifel (Rhineland-Palatinate, Germany) had their last eruptions less than 13,000 years ago. Recently, deep low-frequency (DLF) earthquakes were detected beneath one of the volcanic fields showing evidence of ongoing magmatic activity in the lower crust and upper mantle. In this work, seismic wide- and steep-angle experiments from 1978/1979 and 1987/1988 are compiled, partially reprocessed and interpreted, together with other data to better determine the location, size, shape, and state of magmatic reservoirs in the Eifel region near the crust-mantle boundary. We discuss seismic evidence for a low-velocity gradient layer from 30-36 km depth, which has developed over a large region under all Quaternary volcanic fields of the Rhenish Massif and can be explained by the presence of partial melts. We show that the DLF earthquakes connect the postulated upper mantle reservoir with the upper crust at a depth of about 8 km, directly below one of the youngest phonolitic volcanic centers in the Eifel, where CO(2)originating from the mantle is massively outgassing. A bright spot in the West Eifel between 6 and 10 km depth represents a Tertiary magma reservoir and is seen as a model for a differentiated reservoir beneath the young phonolitic center today. We find that the distribution of volcanic fields is controlled by the Variscan lithospheric structures and terrane boundaries as a whole, which is reflected by an offset of the Moho depth, a wedge-shaped transparent zone in the lower crust and the system of thrusts over about 120 km length.}, language = {en} } @article{HannemannKruegerDahmetal.2016, author = {Hannemann, Katrin and Kr{\"u}ger, Frank and Dahm, Torsten and Lange, Dietrich}, title = {Oceanic lithospheric S-wave velocities from the analysis of P-wave polarization at the ocean floor}, series = {Geophysical journal international}, volume = {207}, journal = {Geophysical journal international}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggw342}, pages = {1796 -- 1817}, year = {2016}, abstract = {Our knowledge of the absolute S-wave velocities of the oceanic lithosphere is mainly based on global surface wave tomography, local active seismic or compliance measurements using oceanic infragravity waves. The results of tomography give a rather smooth picture of the actual S-wave velocity structure and local measurements have limitations regarding the range of elastic parameters or the geometry of the measurement. Here, we use the P-wave polarization (apparent P-wave incidence angle) of teleseismic events to investigate the S-wave velocity structure of the oceanic crust and the upper tens of kilometres of the mantle beneath single stations. In this study, we present an up to our knowledge new relation of the apparent P-wave incidence angle at the ocean bottom dependent on the half-space S-wave velocity. We analyse the angle in different period ranges at ocean bottom stations (OBSs) to derive apparent S-wave velocity profiles. These profiles are dependent on the S-wave velocity as well as on the thickness of the layers in the subsurface. Consequently, their interpretation results in a set of equally valid models. We analyse the apparent P-wave incidence angles of an OBS data set which was collected in the Eastern Mid Atlantic. We are able to determine reasonable S-wave-velocity-depth models by a three-step quantitative modelling after a manual data quality control, although layer resonance sometimes influences the estimated apparent S-wave velocities. The apparent S-wave velocity profiles are well explained by an oceanic PREM model in which the upper part is replaced by four layers consisting of a water column, a sediment, a crust and a layer representing the uppermost mantle. The obtained sediment has a thickness between 0.3 and 0.9 km with S-wave velocities between 0.7 and 1.4 km s(-1). The estimated total crustal thickness varies between 4 and 10 km with S-wave velocities between 3.5 and 4.3 km s(-1). We find a slight increase of the total crustal thickness from similar to 5 to similar to 8 km towards the South in the direction of a major plate boundary, the Gloria Fault. The observed crustal thickening can be related with the known dominant compression in the vicinity of the fault. Furthermore, the resulting mantle S-wave velocities decrease from values around 5.5 to 4.5 km s(-1) towards the fault. This decrease is probably caused by serpentinization and indicates that the oceanic transform fault affects a broad region in the uppermost mantle. Conclusively, the presented method is useful for the estimation of the local S-wave velocity structure beneath ocean bottom seismic stations. It is easy to implement and consists of two main steps: (1) measurement of apparent P-wave incidence angles in different period ranges for real and synthetic data, and (2) comparison of the determined apparent S-wave velocities for real and synthetic data to estimate S-wave velocity-depth models.}, language = {en} } @article{HannemannKruegerDahmetal.2017, author = {Hannemann, Katrin and Kr{\"u}ger, Frank and Dahm, Torsten and Lange, Dietrich}, title = {Structure of the oceanic lithosphere and upper mantle north of the Gloria Fault in the eastern mid-Atlantic by receiver function analysis}, series = {Journal of geophysical research : Solid earth}, volume = {122}, journal = {Journal of geophysical research : Solid earth}, publisher = {American Geophysical Union}, address = {Washington}, issn = {2169-9313}, doi = {10.1002/2016JB013582}, pages = {7927 -- 7950}, year = {2017}, abstract = {Receiver functions (RF) have been used for several decades to study structures beneath seismic stations. Although most available stations are deployed on shore, the number of ocean bottom station (OBS) experiments has increased in recent years. Almost all OBSs have to deal with higher noise levels and a limited deployment time (approximate to 1year), resulting in a small number of usable records of teleseismic earthquakes. Here we use OBSs deployed as midaperture array in the deep ocean (4.5-5.5km water depth) of the eastern mid-Atlantic. We use evaluation criteria for OBS data and beamforming to enhance the quality of the RFs. Although some stations show reverberations caused by sedimentary cover, we are able to identify the Moho signal, indicating a normal thickness (5-8km) of oceanic crust. Observations at single stations with thin sediments (300-400m) indicate that a probable sharp lithosphere-asthenosphere boundary (LAB) might exist at a depth of approximate to 70-80km which is in line with LAB depth estimates for similar lithospheric ages in the Pacific. The mantle discontinuities at approximate to 410km and approximate to 660km are clearly identifiable. Their delay times are in agreement with PREM. Overall the usage of beam-formed earthquake recordings for OBS RF analysis is an excellent way to increase the signal quality and the number of usable events.}, language = {en} } @article{KaramzadehToularoudHeimannDahmetal.2018, author = {Karamzadeh Toularoud, Nasim and Heimann, Sebastian and Dahm, Torsten and Kr{\"u}ger, Frank}, title = {Application based seismological array design by seismicity scenario modelling}, series = {Geophysical journal international}, volume = {216}, journal = {Geophysical journal international}, number = {3}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, pages = {1711 -- 1727}, year = {2018}, abstract = {The design of an array configuration is an important task in array seismology during experiment planning. Often the array response function (ARF), which depends on the relative position of array stations and frequency content of the incoming signals, is used as the array design criterion. In practice, additional constraints and parameters have to be taken into account, for example, land ownership, site-specific noise levels or characteristics of the seismic sources under investigation. In this study, a flexible array design framework is introduced that implements a customizable scenario modelling and optimization scheme by making use of synthetic seismograms. Using synthetic seismograms to evaluate array performance makes it possible to consider additional constraints. We suggest to use synthetic array beamforming as an array design criterion instead of the ARF. The objective function of the optimization scheme is defined according to the monitoring goals, and may consist of a number of subfunctions. The array design framework is exemplified by designing a seven-station small-scale array to monitor earthquake swarm activity in Northwest Bohemia/Vogtland in central Europe. Two subfunctions are introduced to verify the accuracy of horizontal slowness estimation; one to suppress aliasing effects due to possible secondary lobes of synthetic array beamforming calculated in horizontal slowness space and the other to reduce the event's mislocation caused by miscalculation of the horizontal slowness vector. Subsequently, a weighting technique is applied to combine the subfunctions into one single scalar objective function to use in the optimization process.}, language = {en} } @article{FischerHrubcovaDahmetal.2022, author = {Fischer, Tomas and Hrubcova, Pavla and Dahm, Torsten and Woith, Heiko and Vylita, Tomas and Ohrnberger, Matthias and Vlcek, Josef and Horalek, Josef and Dedecek, Petr and Zimmer, Martin and Lipus, Martin P. and Pierdominici, Simona and Kallmeyer, Jens and Kr{\"u}ger, Frank and Hannemann, Katrin and Korn, Michael and K{\"a}mpf, Horst and Reinsch, Thomas and Klicpera, Jakub and Vollmer, Daniel and Daskalopoulou, Kyriaki}, title = {ICDP drilling of the Eger Rift observatory}, series = {Scientific Drilling}, volume = {31}, journal = {Scientific Drilling}, publisher = {Copernicus}, address = {G{\"o}ttingen}, issn = {1816-8957}, doi = {10.5194/sd-31-31-2022}, pages = {31 -- 49}, year = {2022}, abstract = {The new in situ geodynamic laboratory established in the framework of the ICDP Eger project aims to develop the most modern, comprehensive, multiparameter laboratory at depth for studying earthquake swarms, crustal fluid flow, mantle-derived CO2 and helium degassing, and processes of the deep biosphere. In order to reach a new level of high-frequency, near-source and multiparameter observation of earthquake swarms and related phenomena, such a laboratory comprises a set of shallow boreholes with high-frequency 3-D seismic arrays as well as modern continuous real-time fluid monitoring at depth and the study of the deep biosphere. This laboratory is located in the western part of the Eger Rift at the border of the Czech Republic and Germany (in the West Bohemia-Vogtland geodynamic region) and comprises a set of five boreholes around the seismoactive zone. To date, all monitoring boreholes have been drilled. This includes the seismic monitoring boreholes S1, S2 and S3 in the crystalline units north and east of the major Novy Kostel seismogenic zone, borehole F3 in the Hartousov mofette field and borehole S4 in the newly discovered Bazina maar near Liba. Supplementary borehole P1 is being prepared in the Neualbenreuth maar for paleoclimate and biological research. At each of these sites, a borehole broadband seismometer will be installed, and sites S1, S2 and S3 will also host a 3-D seismic array composed of a vertical geophone chain and surface seismic array. Seismic instrumenting has been completed in the S1 borehole and is in preparation in the remaining four monitoring boreholes. The continuous fluid monitoring site of Hartousov includes three boreholes, F1, F2 and F3, and a pilot monitoring phase is underway. The laboratory also enables one to analyze microbial activity at CO2 mofettes and maar structures in the context of changes in habitats. The drillings into the maar volcanoes contribute to a better understanding of the Quaternary paleoclimate and volcanic activity.}, language = {en} } @article{KaramzadehToularoudHeimannDahmetal.2020, author = {Karamzadeh Toularoud, Nasim and Heimann, Sebastian and Dahm, Torsten and Kr{\"u}ger, Frank}, title = {Earthquake source arrays}, series = {Geophysical journal international}, volume = {221}, journal = {Geophysical journal international}, number = {1}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggaa002}, pages = {352 -- 370}, year = {2020}, abstract = {A collection of earthquake sources recorded at a single station, under specific conditions, are considered as a source array (SA), that is interpreted as if earthquake sources originate at the station location and are recorded at the source location. Then, array processing methods, that is array beamforming, are applicable to analyse the recorded signals. A possible application is to use source array multiple event techniques to locate and characterize near-source scatterers and structural interfaces. In this work the aim is to facilitate the use of earthquake source arrays by presenting an automatic search algorithm to configure the source array elements. We developed a procedure to search for an optimal source array element distribution given an earthquake catalogue including accurate origin time and hypocentre locations. The objective function of the optimization process can be flexibly defined for each application to ensure the prerequisites (criteria) of making a source array. We formulated four quantitative criteria as subfunctions and used the weighted sum technique to combine them in one single scalar function. The criteria are: (1) to control the accuracy of the slowness vector estimation using the time domain beamforming method, (2) to measure the waveform coherency of the array elements, (3) to select events with lower location error and (4) to select traces with high energy of specific phases, that is, sp- or ps-phases. The proposed procedure is verified using synthetic data as well as real examples for the Vogtland region in Northwest Bohemia. We discussed the possible application of the optimized source arrays to identify the location of scatterers in the velocity model by presenting a synthetic test and an example using real waveforms.}, language = {en} } @article{KruegerDahmHannemann2020, author = {Kr{\"u}ger, Frank and Dahm, Torsten and Hannemann, Katrin}, title = {Mapping of Eastern North Atlantic Ocean seismicity from Po/So observations at a mid-aperture seismological broad-band deep sea array}, series = {Geophysical journal international}, volume = {221}, journal = {Geophysical journal international}, number = {2}, publisher = {Oxford Univ. Press}, address = {Oxford}, issn = {0956-540X}, doi = {10.1093/gji/ggaa054}, pages = {1055 -- 1080}, year = {2020}, abstract = {A mid-aperture broad-band test array (OBS array DOCTAR) was deployed from June 2011 to April 2012 about 100 km north of the Gloria fault in the Eastern North Atlantic in about 5000 m water depth. In addition arrays were installed on Madeira Island and in western Portugal mainland. For the first time in the Eastern North Atlantic, we recorded a large number of high frequency Po and So waves from local and regional small and moderate earthquakes (M-L < 4). An incoherent beamforming method was adapted to scan continuous data for such Po and So arrivals applying a sliding window waveform migration and frequency-wavenumber technique. We identify about 320 Po and 1550 So arrivals and compare the phase onsets with the ISC catalogue (ISC 2015) for the same time span. Up to a distance of 6 degrees to the DOCTAR stations all events listed in the ISC catalogue could be associated to Po and So phases. Arrivals from events in more than 10 degrees distance could be identified only in some cases. Only few Po and/or So arrivals were detected for earthquakes from the European and African continental area, the continental shelf regions and for earthquakes within or northwest of the Azores plateau. Unexpectedly, earthquake clusters are detected within the oceanic plates north and south of the Gloria fault and far from plate boundaries, indicating active intraplate structures. We also observe and locate numerous small magnitude earthquakes on the segment of the Gloria fault directly south of DOCTAR, which likely coincides with the rupture of the 25 November 1941 event. Local small magnitude earthquakes located beneath DOCTAR show hypocentres up to 30 km depth and strike-slip focal mechanisms. A comparison with detections at temporary mid-aperture arrays on Madeira and in western Portugal shows that the deep ocean array performs much better than the island and the continental array regarding the detection threshold for events in the oceanic plates. We conclude that sparsely distributed mid-aperture seismic arrays in the deep ocean could decrease the detection and location threshold for seismicity with M-L < 4 in the oceanic plate and might constitute a valuable tool to monitor oceanic plate seismicity.}, language = {en} } @misc{KriegerowskiCescaOhrnbergeretal.2018, author = {Kriegerowski, Marius and Cesca, Simone and Ohrnberger, Matthias and Dahm, Torsten and Kr{\"u}ger, Frank}, title = {Event couple spectral ratio Q method for earthquake clusters}, series = {Postprints der Universit{\"a}t Potsdam Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam Mathematisch-Naturwissenschaftliche Reihe}, number = {683}, doi = {10.25932/publishup-42602}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-426029}, pages = {12}, year = {2018}, abstract = {We develop an amplitude spectral ratio method for event couples from clustered earthquakes to estimate seismic wave attenuation (Q-1) in the source volume. The method allows to study attenuation within the source region of earthquake swarms or aftershocks at depth, independent of wave path and attenuation between source region and surface station. We exploit the high-frequency slope of phase spectra using multitaper spectral estimates. The method is tested using simulated full wave-field seismograms affected by recorded noise and finite source rupture. The synthetic tests verify the approach and show that solutions are independent of focal mechanisms but also show that seismic noise may broaden the scatter of results. We apply the event couple spectral ratio method to northwest Bohemia, Czech Republic, a region characterized by the persistent occurrence of earthquake swarms in a confined source region at mid-crustal depth. Our method indicates a strong anomaly of high attenuation in the source region of the swarm with an averaged attenuation factor of Qp < 100. The application to S phases fails due to scattered P-phase energy interfering with S phases. The Qp anomaly supports the common hypothesis of highly fractured and fluid saturated rocks in the source region of the swarms in northwest Bohemia. However, high temperatures in a small volume around the swarms cannot be excluded to explain our observations.}, language = {en} } @article{KriegerowskiCescaOhrnbergeretal.2019, author = {Kriegerowski, Marius and Cesca, Simone and Ohrnberger, Matthias and Dahm, Torsten and Kr{\"u}ger, Frank}, title = {Event couple spectral ratio Q method for earthquake clusters}, series = {Solid Earth}, journal = {Solid Earth}, number = {10}, publisher = {Copernicus Publications}, address = {G{\"o}ttingen}, issn = {1869-9529}, doi = {10.5194/se-10-317-2019}, pages = {317 -- 328}, year = {2019}, abstract = {We develop an amplitude spectral ratio method for event couples from clustered earthquakes to estimate seismic wave attenuation (Q-1) in the source volume. The method allows to study attenuation within the source region of earthquake swarms or aftershocks at depth, independent of wave path and attenuation between source region and surface station. We exploit the high-frequency slope of phase spectra using multitaper spectral estimates. The method is tested using simulated full wave-field seismograms affected by recorded noise and finite source rupture. The synthetic tests verify the approach and show that solutions are independent of focal mechanisms but also show that seismic noise may broaden the scatter of results. We apply the event couple spectral ratio method to northwest Bohemia, Czech Republic, a region characterized by the persistent occurrence of earthquake swarms in a confined source region at mid-crustal depth. Our method indicates a strong anomaly of high attenuation in the source region of the swarm with an averaged attenuation factor of Qp < 100. The application to S phases fails due to scattered P-phase energy interfering with S phases. The Qp anomaly supports the common hypothesis of highly fractured and fluid saturated rocks in the source region of the swarms in northwest Bohemia. However, high temperatures in a small volume around the swarms cannot be excluded to explain our observations.}, language = {en} }