@article{TurhanSaracGencturketal.2012, author = {Turhan, Metehan C. and Sarac, A. Sezai and Gencturk, Asli and Gilsing, Hans-Detlev and Faltz, Heike and Schulz, Burkhard}, title = {Electrochemical impedance characterization and potential dependence of poly[3,4-(2,2-dibutylpropylenedioxy)thiophene] nanostructures on single carbon fiber microelectrode}, series = {Synthetic metals : the journal of electronic polymers and electronic molecular materials}, volume = {162}, journal = {Synthetic metals : the journal of electronic polymers and electronic molecular materials}, number = {5-6}, publisher = {Elsevier}, address = {Lausanne}, issn = {0379-6779}, doi = {10.1016/j.synthmet.2012.01.012}, pages = {511 -- 515}, year = {2012}, abstract = {The electropolymerization of 3,4-(2,2-dibutylpropylenedioxy)thiophene (ProDOT-Bu-2) onto single carbon fiber microelectrode (SCFME) was conducted in acetonitrile (ACN) containing sodium perchlorate (NaClO4) as electrolyte and investigated by cyclic voltammetry (CV). The nanostructured films of poly[3,4-(2,2-dibutyl-propyleneclioxy)thiophene] (PProDOT-Bu-2) which were depositing showed complete reversible redox behavior in monomer-free electrolyte solution. The capacitive behavior of the films was investigated by electrochemical impedance spectroscopy (EIS) at applied potentials from 0.1 V to 1.3 V. The analysis by equivalent circuit modeling revealed an applied potential around 0.4V to be most suitable for the system PProDOT-Bu-2/SCFME as a double layer supercapacitor component inducing a double layer capacitance C-d, value of 62 mFcm(-2).}, language = {en} } @article{SarauliPetersXuetal.2014, author = {Sarauli, David and Peters, Kristina and Xu, Chenggang and Schulz, Burkhard and Fattakhova-Rohlfing, Dina and Lisdat, Fred}, title = {3D-Electrode architectures for enhanced direct bioelectrocatalysis of pyrroloquinoline quinone-dependent glucose dehydrogenase}, series = {ACS applied materials \& interfaces}, volume = {6}, journal = {ACS applied materials \& interfaces}, number = {20}, publisher = {American Chemical Society}, address = {Washington}, issn = {1944-8244}, doi = {10.1021/am5046026}, pages = {17887 -- 17893}, year = {2014}, abstract = {We report on the fabrication of a complex electrode architecture for efficient direct bioelectrocatalysis. In the developed procedure, the redox enzyme pyrroloquinoline quinone-dependent glucose dehydrogenase entrapped in a sulfonated polyaniline [poly(2-methoxyaniline-5-sulfonic acid)-co-aniline] was immobilized on macroporous indium tin oxide (macroITO) electrodes. The use of the 3D-conducting scaffold with a large surface area in combination with the conductive polymer enables immobilization of large amounts of enzyme and its efficient communication with the electrode, leading to enhanced direct bioelectrocatalysis. In the presence of glucose, the fabricated bioelectrodes show an exceptionally high direct bioelectrocatalytical response without any additional mediator. The catalytic current is increased more than 200-fold compared to planar ITO electrodes. Together with a high long-term stability (the current response is maintained for >90\% of the initial value even after 2 weeks of storage), the transparent 3D macroITO structure with a conductive polymer represents a valuable basis for the construction of highly efficient bioelectronic units, which are useful as indicators for processes liberating glucose and allowing optical and electrochemical transduction.}, language = {en} } @article{SchoeneSchulzRichauetal.2014, author = {Sch{\"o}ne, Anne-Christin and Schulz, Burkhard and Richau, Klaus and Kratz, Karl and Lendlein, Andreas}, title = {Characterization of Langmuir films prepared from copolyesterurethanes based on oligo(omega-pentadecalactone) and oligo(epsilon-caprolactone)segments}, series = {Macromolecular chemistry and physics}, volume = {215}, journal = {Macromolecular chemistry and physics}, number = {24}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1352}, doi = {10.1002/macp.201400377}, pages = {2437 -- 2445}, year = {2014}, abstract = {A series of multiblock copolymers (PDLCL) synthesized from oligo(omega-pentadecalactone) diol (OPDL) and oligo(epsilon-caprolactone) diol (OCL), which are linked by 2,2(4), 4-trimethyl-hexamethylene diisocyanate (TMDI), is investigated by the Langmuir monolayer technique at the air-water interface. Brewster angle microscopy (BAM) and spectroscopic ellipsometry are employed to characterize the polymer film morphologies in situ. PDLCL containing >= 40 wt\% OCL segments form homogeneous Langmuir monofilms after spreading. The film elasticity modulus decreases with increasing amounts of OPDL segments in the copolymer. In contrast, the OCL-free polyesterurethane OPDL-TMDI cannot be spread to monomolecular films on the water surface properly, and movable slabs are observed by BAM even at low surface pressures. The results of the in situ morphological characterization clearly show that essential information concerning the reliability of Langmuir monolayer degradation (LMD) experiments cannot be obtained from the evaluation of the pi-A isotherms only. Consequently, in situ morphological characterization turns out to be indispensable for characterization of Langmuir layers before LMD experiments.}, language = {en} } @article{JetzschmannJagerszkiDechtriratetal.2015, author = {Jetzschmann, Katharina J. and Jagerszki, Gyula and Dechtrirat, Decha and Yarman, Aysu and Gajovic-Eichelmann, Nenad and Gilsing, Hans-Detlev and Schulz, Burkhard and Gyurcsanyi, Robert E. and Scheller, Frieder W.}, title = {Vectorially Imprinted Hybrid Nanofilm for Acetylcholinesterase Recognition}, series = {Advanced functional materials}, volume = {25}, journal = {Advanced functional materials}, number = {32}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1616-301X}, doi = {10.1002/adfm.201501900}, pages = {5178 -- 5183}, year = {2015}, abstract = {Effective recognition of enzymatically active tetrameric acetylcholinesterase (AChE) is accomplished by a hybrid nanofilm composed of a propidium-terminated self-assembled monolayer (Prop-SAM) which binds AChE via its peripheral anionic site (PAS) and an ultrathin electrosynthesized molecularly imprinted polymer (MIP) cover layer of a novel carboxylate-modified derivative of 3,4-propylenedioxythiophene. The rebinding of the AChE to the MIP/Prop-SAM nanofilm covered electrode is detected by measuring in situ the enzymatic activity. The oxidative current of the released thiocholine is dependent on the AChE concentration from approximate to 0.04 x 10(-6) to 0.4 x 10(-6)m. An imprinting factor of 9.9 is obtained for the hybrid MIP, which is among the best values reported for protein imprinting. The dissociation constant characterizing the strength of the MIP-AChE binding is 4.2 x 10(-7)m indicating the dominant role of the PAS-Prop-SAM interaction, while the benefit of the MIP nanofilm covering the Prop-SAM layer is the effective suppression of the cross-reactivity toward competing proteins as compared with the Prop-SAM. The threefold selectivity gain provided by i) the shape-specific MIP filter, ii) the propidium-SAM, iii) signal generation only by the AChE bound to the nanofilm shows promise for assessing AChE activity levels in cerebrospinal fluid.}, language = {en} } @article{GulerGilsingSchulzetal.2012, author = {Guler, Fatma G. and Gilsing, Hans-Detlev and Schulz, Burkhard and Sarac, A. Sezai}, title = {Impedance and morphology of hydroxy- and chloro-functionalized poly(3,4-propylenedioxythiophene) nanostructures}, series = {Journal of nanoscience and nanotechnolog}, volume = {12}, journal = {Journal of nanoscience and nanotechnolog}, number = {10}, publisher = {American Scientific Publ.}, address = {Valencia}, issn = {1533-4880}, doi = {10.1166/jnn.2012.6594}, pages = {7869 -- 7878}, year = {2012}, abstract = {The new 3,4-propylenedioxythiophenes (ProDOT) bearing hydroxy- or chloro-functionalized side chains of varying length and polarity were synthesized and electropolymerized on single carbon fiber microelectrode (SCFME) using cyclo-voltammetry. Electrochemical impedance spectroscopy (EIS) revealed highest capacitance values for the hydroxy-functionalized Poly 5 carrying a side chain of medium length. The EIS data were fitted with an equivalent electrical circuit giving a good correlation. AFM analysis of the topography showed higher roughness values for Poly 5 than for the two other polymers bearing longer side chains. Due to their reactive end groups the polymers should be useful for post-polymerization functionalization of the electrode surface.}, language = {en} } @article{HoffmannDietzelSchulzetal.2011, author = {Hoffmann, Katrin and Dietzel, Birgit and Schulz, Burkhard and Reck, Guenter and Hoffmann, Angelika and Orgzall, Ingo and Resch-Genger, Ute and Emmerling, Franziska}, title = {Combined structural and fluorescence studies of methyl-substituted 2,5-diphenyl-1,3,4-oxadiazoles - Relation between electronic properties and packing motifs}, series = {Journal of molecular structure}, volume = {988}, journal = {Journal of molecular structure}, number = {1-3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0022-2860}, doi = {10.1016/j.molstruc.2010.11.071}, pages = {35 -- 46}, year = {2011}, abstract = {Prerequisite for the rational design of functional organic materials with tailor-made electronic properties is the knowledge of the structure-property relationship for the specific class of molecules under consideration. This encouraged us to systematically study the influence of the molecular structure and substitution pattern of aromatically substituted 1,3,4-oxadiazoles on the electronic properties and packing motifs of these molecules and on the interplay of these factors. For this purpose, seven diphenyl-oxadiazoles equipped with methyl substituents in the ortho- and meta-position(s) were synthesized and characterized. Absorption and fluorescence spectra in solution served here as tools to monitor substitution-induced changes in the electronic properties of the individual molecules whereas X-ray and optical measurements in the solid state provided information on the interplay of electronic and packing effects. In solution, the spectral position of the absorption maximum, the size of Stokes shift, and the fluorescence quantum yield are considerably affected by ortho-substitution in three or four ortho-positions. This results in blue shifted absorption bands, increased Stokes shifts, and reduced fluorescence quantum yields whereas the spectral position and vibrational structure of the emission bands remain more or less unaffected. In the crystalline state, however, the spectral position and shape of the emission bands display a strong dependence on the molecular structure and/or packing motifs that seem to control the amount of dye-dye-interactions. These observations reveal the limited value of commonly reported absorption and fluorescence measurements in solution for a straightforward comparison of spectroscopic results with single X-ray crystallography. This underlines the importance of solid state spectroscopic studies for a better understanding of the interplay of electronic effects and molecular order.}, language = {en} } @article{EmmerlingOrgzallDietzeletal.2012, author = {Emmerling, Franziska and Orgzall, Ingo and Dietzel, Birgit and Schulz, Burkhard and Larrucea, Julen}, title = {Ordering the amorphous - Structures in PBD LED materials}, series = {Journal of molecular structure}, volume = {1030}, journal = {Journal of molecular structure}, number = {23}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0022-2860}, doi = {10.1016/j.molstruc.2012.04.040}, pages = {209 -- 215}, year = {2012}, abstract = {The class of 2,5 disubstituted-1,3,4-oxadiazoles containing a biphenyl unit on one side is intensively used as electron transport materials to enhance the performance of organic light emitting diodes (OLEDs). In contrast to the ongoing research on these materials insights in their structure-property relationships are still incomplete. To overcome the structural tentativeness and ambiguities the crystal structures of 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole, that of the related compound 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole and of 2-(4-biphenylyl)-5-(2,6-dimethylphenyl)-1,3,4-oxadiazole are determined. A comparison with the results of GAUSSIAN03 calculations and similar compounds in the Cambridge Structural Database leads to a profound characterization.}, language = {en} } @article{SchoeneRichauKratzetal.2015, author = {Sch{\"o}ne, Anne-Christin and Richau, Klaus and Kratz, Karl and Schulz, Burkhard and Lendlein, Andreas}, title = {Influence of Diurethane Linkers on the Langmuir Layer Behavior of Oligo[(rac-lactide)-co-glycolide]-based Polyesterurethanes}, series = {Macromolecular rapid communications}, volume = {36}, journal = {Macromolecular rapid communications}, number = {21}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1336}, doi = {10.1002/marc.201500316}, pages = {1910 -- 1915}, year = {2015}, abstract = {Three oligo[(rac-lactide)-co-glycolide] based polyesterurethanes (OLGA-PUs) containing different diurethane linkers are investigated by the Langmuir monolayer technique and compared to poly[(rac-lactide)-co-glycolide] (PLGA) to elucidate the influence of the diurethane junction units on hydrophilicity and packing motifs of these polymers at the air-water interface. The presence of diurethane linkers does not manifest itself in the Langmuir layer behavior both in compression and expansion experiments when monomolecular films of OLGA-PUs are spread on the water surface. However, the linker retard the evolution of morphological structures at intermediate compression level under isobaric conditions (with a surface pressure greater than 11 mN m(-1)) compared to the PLGA, independent on the chemical structure of the diurethane moiety. The layer thicknesses of both OLGA-PU and PLGA films decrease in the high compression state with decreasing surface pressure, as deduced from ellipsometric data. All films must be described with the effective medium approximation as water swollen layers.}, language = {en} } @article{SarauliXuDietzeletal.2012, author = {Sarauli, David and Xu, Chenggang and Dietzel, Birgit and Stiba, Konstanze and Leimk{\"u}hler, Silke and Schulz, Burkhard and Lisdat, Fred}, title = {Thin films of substituted polyanilines interactions with biomolecular systems}, series = {Soft matter}, volume = {8}, journal = {Soft matter}, number = {14}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, issn = {1744-683X}, doi = {10.1039/c2sm07261k}, pages = {3848 -- 3855}, year = {2012}, abstract = {We use substituted polyanilines for the construction of new polymer electrodes for interaction studies with the redox protein cytochrome c (cyt c) and the enzyme sulfite oxidase (SO). For these purposes four different polyaniline copolymers are chemically synthesized. Three of them are copolymers, containing 2-methoxyaniline-5-sulfonic acid with variable ratios of aniline; the fourth copolymer consists of 3-amino-benzoic acid and aniline. The results show that all polymers are suitable for being immobilized as thin stable films on gold wire and indium tin oxide (ITO) electrode surfaces from DMSO solution. This can be demonstrated by cyclic voltammetry and UV-Vis spectroscopy measurements. Moreover, cyt c can be electrochemically detected not only in solution, but also immobilized on top of the polymer films. Furthermore, the appearance of a significant catalytic current has been demonstrated for the sulfonated polyanilines, when the polymer-coated protein electrode is being measured upon addition of sulfite oxidase, confirming the establishment of a bioanalytical signal chain. Best results have been obtained for the polymer with highest sulfonation grade. The redox switching of the polymer by the enzymatic reaction can also be analyzed by following the spectral properties of the polymer electrode.}, language = {en} } @article{SchoeneSchulzLendlein2016, author = {Sch{\"o}ne, Anne-Christin and Schulz, Burkhard and Lendlein, Andreas}, title = {Stimuli Responsive and Multifunctional Polymers: Progress in Materials and Applications}, series = {Macromolecular rapid communications}, volume = {37}, journal = {Macromolecular rapid communications}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1336}, doi = {10.1002/marc.201600650}, pages = {1856 -- 1859}, year = {2016}, language = {en} } @article{SchoeneKratzSchulzetal.2016, author = {Sch{\"o}ne, Anne-Christin and Kratz, Karl and Schulz, Burkhard and Lendlein, Andreas}, title = {The relevance of hydrophobic segments in multiblock copolyesterurethanes for their enzymatic degradation at the air-water interface}, series = {Polymer : the international journal for the science and technology of polymers}, volume = {102}, journal = {Polymer : the international journal for the science and technology of polymers}, publisher = {Elsevier}, address = {Oxford}, issn = {0032-3861}, doi = {10.1016/j.polymer.2016.09.001}, pages = {92 -- 98}, year = {2016}, abstract = {The interplay of an enzyme with a multiblock copolymer PDLCL containing two segments of different hydrophilicity and degradability is explored in thin films at the air-water interface. The enzymatic degradation was studied in homogenous Langmuir monolayers, which are formed when containing more than 40 wt\% oligo(epsilon-caprolactone) (OCL). Enzymatic degradation rates were significantly reduced with increasing content of hydrophobic oligo(omega-pentadecalactone) (OPDL). The apparent deceleration of the enzymatic process is caused by smaller portion of water-soluble degradation fragments formed from degradable OCL fragments. Beside the film degradation, a second competing process occurs after adding lipase from Pseudomonas cepacia into the subphase, namely the enrichment of the lipase molecules in the polymeric monolayer. The incorporation of the lipase into the Langmuir film is experimentally revealed by concurrent surface area enlargement and by Brewster angle microscopy (BAM). Aside from the ability to provide information about the degradation behavior of polymers, the Langmuir monolayer degradation (LMD) approach enables to investigate polymer-enzyme interactions for non-degradable polymers. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{SchoeneKratzSchulzetal.2016, author = {Sch{\"o}ne, Anne-Christin and Kratz, Karl and Schulz, Burkhard and Lendlein, Andreas}, title = {Polymer architecture versus chemical structure as adjusting tools for the enzymatic degradation of oligo(epsilon-caprolactone) based films at the air-water interface}, series = {Polymer Degradation and Stability}, volume = {131}, journal = {Polymer Degradation and Stability}, publisher = {Elsevier}, address = {Oxford}, issn = {0141-3910}, doi = {10.1016/j.polymdegradstab.2016.07.010}, pages = {114 -- 121}, year = {2016}, abstract = {The enzymatic degradation of oligo(epsilon-caprolactone) (OCL) based films at the air-water interface is investigated by Langmuir monolayer degradation (LMD) experiments to elucidate the influence of the molecular architecture and of the chemical structure on the chain scission process. For that purpose, the interactions of 2D monolayers of two star-shaped poly(epsilon-caprolactone)s (PCLs) and three linear OCL based copolyesterurethanes (P(OCL-U)) with the lipase from Pseudomonas cepacia are evaluated in comparison to linear OCL. While the architecture of star-shaped PCL Langmuir layers slightly influences their degradability compared to OCL films, significantly retarded degradations are observed for P(OCL-U) films containing urethane junction units derived from 2, 2 (4), 4-trimethyl hexamethylene diisocyanate (TMDI), hexamethylene diisocyanate (HDI) or lysine ethyl ester diisocyanate (LDI). The enzymatic degradation of the OCL based 2D structures is related to the presence of hydrophilic groups within the macromolecules rather than to the packing density of the film or to the molecular weight. The results reveal that the LMD technique allows the parallel analysis of both the film/enzyme interactions and the degradation process on the molecular level. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{SarauliBorowskiPetersetal.2016, author = {Sarauli, David and Borowski, Anja and Peters, Kristina and Schulz, Burkhard and Fattakhova-Rohlfing, Dina and Leimk{\"u}hler, Silke and Lisdat, Fred}, title = {Investigation of the pH-Dependent Impact of Sulfonated Polyaniline on Bioelectrocatalytic Activity of Xanthine Dehydrogenase}, series = {ACS catalysis}, volume = {6}, journal = {ACS catalysis}, publisher = {American Chemical Society}, address = {Washington}, issn = {2155-5435}, doi = {10.1021/acscatal.6b02011}, pages = {7152 -- 7159}, year = {2016}, abstract = {We report on the pH-dependent bioelectrocatalytic activity of the redox enzyme xanthine dehydrogenase (XDH) in the presence of sulfonated polyaniline PMSA1 (poly(2-methoxyaniline-5-sulfonic acid)-co-aniline). Ultraviolet-visible (UV-vis) spectroscopic measurements with both components in solution reveal electron transfer from the hypoxanthine (HX)-reduced enzyme to the polymer. The enzyme shows bioelectrocatalytic activity on indium tin oxide (ITO) electrodes, when the polymer is present. Depending on solution pH, different processes can be identified. It can be demonstrated that not only product-based communication with the electrode but also efficient polymer-supported bioelectrocatalysis occur. Interestingly, substrate dependent catalytic currents can be obtained in acidic and neutral solutions, although the highest activity of XDH with natural reaction partners is in the alkaline region. Furthermore, operation of the enzyme electrode without addition of the natural cofactor of XDH is feasible. Finally, macroporous ITO electrodes have been used as an immobilization platform for the fabrication of HX-sensitive electrodes. The study shows that the efficient polymer/enzyme interaction can be advantageously combined with the open structure of an electrode material of controlled pore size, resulting in good processability, stability, and defined signal transfer in the presence of a substrate.}, language = {en} } @article{HamaciucBrumaKoepnicketal.2001, author = {Hamaciuc, E. and Bruma, Maria and K{\"o}pnick, Thomas and Kaminorz, Yvette and Schulz, Burkhard}, title = {Synthesis and Study of New Silicon-containing Polyoxadiazoles}, year = {2001}, abstract = {A series of new poly-1,3,4-oxadiazoles has been synthesized by polycondensation reaction of hydrazine sulfate with a mixture of a dicarboxylic acid containing unsaturated bonds and a dicarboxylic acid containing silicon, by using methanesulfonic acid/phosphorus pentoxide as a reaction medium. These polymers were highly thermostable but they were only soluble in strong inorganic acids such as sulfuric or methanesulfonic ones. An alternative way was followed by using the corresponding dihydrazides containing unsaturated bonds and the corresponding diacid chloride containing silicon that reacted in N-methylpyrrolidinone (NMP) to give soluble silicon-containing unsaturated polyhydrazides, which were cyclodehydrated either by thermal or chemical treatment to give the corresponding polyoxadiazoles. Very thin coatings of polyhydrazides and polyoxadiazoles were deposited onto silicon wafers and they showed a very smooth surface, free of pinholes, when studied by atomic force microscopy (AFM). Some polyoxadiazole films showed strong blue photoluminescence.}, language = {en} } @article{KaminorzSchulzBrehmer2000, author = {Kaminorz, Yvette and Schulz, Burkhard and Brehmer, Ludwig}, title = {Optical and Electrical Properties of Substituted 2,5-Diphenyl-1,3,4-Oxadiazoles}, year = {2000}, abstract = {New substituted 2,5-diphenyl-1,3,4-oxadiazoles are reported as luminescent materials in light emitting diodes LEDs . The investigated new oxadiazoles show efficient blue and green emission in single layer devices. The combination with a hole transporting and red emitting polythiophene led to a white emission with higher quantum efficiency (QE).}, language = {en} } @article{KarageorgievStillerPrescheretal.2000, author = {Karageorgiev, Peter and Stiller, Burkhard and Prescher, Dietrich and Dietzel, Birgit and Schulz, Burkhard and Brehmer, Ludwig}, title = {Modification of the surface potential of azobenzene-containing langmuir-blodgett films in the near field of a scanning kelvin microscope tip by irradiation}, year = {2000}, language = {en} } @article{GieblerSchulzReicheetal.1999, author = {Giebler, Rainer and Schulz, Burkhard and Reiche, J{\"u}rgen and Brehmer, Ludwig and W{\"u}hn, Mario and W{\"o}ll, Christoph and Smith, Andrew Phillip and Urquhart, Steven G. and Ade, Harald W. and Unger, Wolfgang E. S.}, title = {Near-edge x-ray absorption fine structure spectroscopy on ordered films of an amphiphilic derivate of 2,5- Diphenyl-1,3,4-oxadiazole}, year = {1999}, abstract = {The surfaces of ordered films formed from an amphiphilic derivative of 2,5-diphenyl-1,3,4-oxadiazole by the Langmuir-Blodgett (LB) technique and organic molecular beam deposition (OMBD) were investigated by the use of near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. For the assignment of the spectral features of the C, N, and O K- edge absorption spectra, fingerprint spectra of poly(p-phenylene terephthalamide)(Kevlar), poly(ethylene terephthalate), poly(p-phenylene-1,3,4-oxadiazole), and 2,5-di- (pentadecyl)-1,3,4-oxadiazole, which contain related chemical moieties, were recorded. Ab initio molecular orbital calculations, performed with explicit treatment of the core hole, are used to support the spectral interpretations. Angle-resolved NEXAFS spectroscopy at the C, N, and O K-edges suggests a preferentially upright orientation of the oxadiazole derivative in the outermost layer of the films. X-ray specular reflectivity data and molecular modeling results suggest a similar interpretation.}, language = {en} } @article{BrumaSchulzKoepnicketal.1999, author = {Bruma, Maria and Schulz, Burkhard and K{\"o}pnick, Thomas and Stiller, Burkhard and Belomoina, Nataliya and Mercer, Frank W.}, title = {Synthesis and study of aromatic polyamides containing silicon and phenylquinoxaline rings in the main chain}, year = {1999}, abstract = {New poly(phenylquinoxaline-amide)s with silicon in the main chain have been prepared by polycondensation reaction of a diacid chloride, namely bis(p-chlorocarbonyl-phenyl)-diphenylsilane, with aromatic diamines containing one or two phenylquinoxaline rings separated by a flexible bridge such as ether or methylene. These polymers were easily soluble in polar aprotic solvents such as N-methylpyrrolidinone (NMP) and dimethylformamide (DMF) and showed high thermal stability with decomposition temperature being above 450°C and glass transition temperature in the range of 260- 304°C. Polymer solutions in NMP were processed into thin flexible films which exhibited very smooth surfaces, free of pinholes when studied by atomic force microscopy. The free-standing films showed a dielectric constant in the range of 3.6-3.7.}, language = {en} } @article{BrumaHamciucSchulzetal.1999, author = {Bruma, Maria and Hamciuc, Elena and Schulz, Burkhard and K{\"o}pnick, Thomas and Stiller, Burkhard and Mercer, Frank W.}, title = {Synthesis of fluorinated poly(phenylquinoxaline-amide)s and study of thin films made therefrom}, year = {1999}, abstract = {A series of five fluorinated poly(phenylquinoxaline-amide)s were synthesized by a polycondensation reaction of a diacid chloride containing the hexafluoroisopropylidene (6F) group, namely 2,2-bis(p-chlorocarbonylphenyl)- hexafluoropropane, with various aromatic diamines incorporating two phenyl-substituted quinoxaline rings. These polymers were easily soluble in polar aprotic solvents such as N-methylpyrrolione (NMP), dimethylformamide (DMF), and tetrahydrofurane (THF), and showed a high thermal stability with decomposition temperatures above 400 °C and glass transition temperatures in the range of 260-290 Tg. Polymer solutions in NMP were processed into free-standing films that showed low dielectric constant values, in the range of 3.4-3.9, and good mechanical properties, with tensile strength in the range of 40-80 MPa and elongation to break in the range of 22-55\%. Very thin films, in the range of tens of nanometer, which were deposited onto silicon wafers exhibited very smooth surfaces, free of pinholes when studied by atomic force microscopy (AFM).}, language = {en} } @article{BrumaSchulzKoepnicketal.1999, author = {Bruma, Maria and Schulz, Burkhard and K{\"o}pnick, Thomas and Stiller, Burkhard and Mercer, Frank W.}, title = {Study of thin films made from aromatic polyamides with silicon and phenylquinoxaline rings in the main chain}, year = {1999}, abstract = {Aromatic polyamides containing silicon and phenylquinoxaline rings in the main chain have been prepared by polycondensation reaction of a silicon-containing diacid chloride, namely bis(p-chlorocarbonylphenyl) -diphenylsilane, with various aromatic diamines having preformed phenylquinoxaline units. These polymers were easily soluble in polar aprotic solvents, such as N-methylpyrrolidinone (NMP) and dimethylformamide (DMF), and in tetrahydrofurane. They showed high thermal stability with decomposition temperature being above 450°C and glass transition temperature in the range of 253-304°C. Polymer solutions in NMP were processed into thin films having the thickness of tens of nanometer to 10 mm, by spin-coating onto glass plates or silicon wafers. The films had strong adhesion to substrates and exhibited very smooth surfaces, free of pinholes, in atomic force microscopy (AFM) studies. The free-standing films had dielectric constant in the range of 3.48-3.69. Thermal treatment of the films up to 350°C rendered them completely insoluble in organic solvents, while maintaining their smoothness and strong adhesion to the silicon substrate, and with no Tg in DSC experiments. Their FTIR spectra did not show any changes compared to the untreated films, meaning that polymers maintain their structural integrity at high temperature. {\´O} 1999 Elsevier Science S.A. All rights reserved.}, language = {en} }