@article{AlbrechtJanietzSchindleretal.2012,
  author    = {Albrecht, Steve and Janietz, Silvia and Schindler, Wolfram and Frisch, Johannes and Kurpiers, Jona and Kniepert, Juliane and Inal, Sahika and Pingel, Patrick and Fostiropoulos, Konstantinos and Koch, Norbert and Neher, Dieter},
  title     = {Fluorinated Copolymer PCPDTBT with enhanced open-circuit voltage and reduced recombination for highly efficient polymer solar cells},
  series = {Journal of the American Chemical Society},
  volume    = {134},
  journal   = {Journal of the American Chemical Society},
  number    = {36},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {0002-7863},
  doi       = {10.1021/ja305039j},
  pages     = {14932 -- 14944},
  year      = {2012},
  abstract  = {A novel fluorinated copolymer (F-PCPDTBT) is introduced and shown to exhibit significantly higher power conversion efficiency in bulk heterojunction solar cells with PC70BM compared to the well-known low-band-gap polymer PCPDTBT. Fluorination lowers the polymer HOMO level, resulting in high open-circuit voltages well exceeding 0.7 V. Optical spectroscopy and morphological studies with energy-resolved transmission electron microscopy reveal that the fluorinated polymer aggregates more strongly in pristine and blended layers, with a smaller amount of additives needed to achieve optimum device performance. Time-delayed collection field and charge extraction by linearly increasing voltage are used to gain insight into the effect of fluorination on the field dependence of free charge-carrier generation and recombination. F-PCPDTBT is shown to exhibit a significantly weaker field dependence of free charge-carrier generation combined with an overall larger amount of free charges, meaning that geminate recombination is greatly reduced. Additionally, a 3-fold reduction in non-geminate recombination is measured compared to optimized PCPDTBT blends. As a consequence of reduced non-geminate recombination, the performance of optimized blends of fluorinated PCPDTBT with PC70BM is largely determined by the field dependence of free-carrier generation, and this field dependence is considerably weaker compared to that of blends comprising the non-fluorinated polymer. For these optimized blends, a short-circuit current of 14 mA/cm(2), an open-circuit voltage of 0.74 V, and a fill factor of 58\% are achieved, giving a highest energy conversion efficiency of 6.16\%. The superior device performance and the low band-gap render this new polymer highly promising for the construction of efficient polymer-based tandem solar cells.},
  language  = {en}
}
@article{LangeKniepertPingeletal.2013,
  author    = {Lange, Ilja and Kniepert, Juliane and Pingel, Patrick and Dumsch, Ines and Allard, Sybille and Janietz, Silvia and Scherf, Ullrich and Neher, Dieter},
  title     = {Correlation between the open circuit voltage and the energetics of organic bulk heterojunction solar cells},
  series = {The journal of physical chemistry letters},
  volume    = {4},
  journal   = {The journal of physical chemistry letters},
  number    = {22},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1948-7185},
  doi       = {10.1021/jz401971e},
  pages     = {3865 -- 3871},
  year      = {2013},
  abstract  = {A detailed investigation of the open circuit voltage (V-OC) of organic bulk heterojunction solar cells comprising three different donor polymers and two different fullerene-based acceptors is presented. Bias amplified charge extraction (BACE) is combined with Kelvin Probe measurements to derive information on the relevant energetics in the blend. On the example of P3HT:PC70BM the influence of composition and preparation conditions on the relevant transport levels will be shown. Moderate upward shifts of the P3HT HOMO depending on crystallinity are observed, but contrarily to common believe, the dependence of V-OC on blend composition and thermal history is found to be largely determined by the change in the PCBM LUMO energy. Following this approach, we quantified the energetic contribution to the V-OC in blends with fluorinated polymers or higher adduct fullerenes.},
  language  = {en}
}
@article{PingelArvindKoellnetal.2016,
  author    = {Pingel, Patrick and Arvind, Malavika and K{\"o}lln, Lisa and Steyrleuthner, Robert and Kraffert, Felix and Behrends, Jan and Janietz, Silvia and Neher, Dieter},
  title     = {p-Type Doping of Poly(3-hexylthiophene) with the Strong Lewis Acid Tris(pentafluorophenyl)borane},
  series = {Advanced electronic materials},
  volume    = {2},
  journal   = {Advanced electronic materials},
  publisher = {Wiley-Blackwell},
  address   = {Hoboken},
  issn      = {2199-160X},
  doi       = {10.1002/aelm.201600204},
  pages     = {7},
  year      = {2016},
  abstract  = {State-of-the-art p-type doping of organic semiconductors is usually achieved by employing strong -electron acceptors, a prominent example being tetrafluorotetracyanoquinodimethane (F(4)TCNQ). Here, doping of the semiconducting model polymer poly(3-hexylthiophene), P3HT, using the strong Lewis acid tris(pentafluorophenyl)borane (BCF) as a dopant, is investigated by admittance, conductivity, and electron paramagnetic resonance measurements. The electrical characteristics of BCF- and F(4)TCNQ-doped P3HT layers are shown to be very similar in terms of the mobile hole density and the doping efficiency. Roughly 18\% of the employed dopants create mobile holes in either F-4 TCNQ- or BCF-doped P3HT, while the majority of doping-induced holes remain strongly Coulomb-bound to the dopant anions. Despite similar hole densities, conductivity and hole mobility are higher in BCF-doped P3HT layers than in F(4)TCNQ-doped samples. This and the good solubility in many organic solvents render BCF very useful for p-type doping of organic semiconductors.},
  language  = {en}
}