@article{StolterfohtLeCorreFeuersteinetal.2019,
  author    = {Stolterfoht, Martin and Le Corre, Vincent M. and Feuerstein, Markus and Caprioglio, Pietro and Koster, Lambert Jan Anton and Neher, Dieter},
  title     = {Voltage-Dependent Photoluminescence and How It Correlates with the Fill Factor and Open-Circuit Voltage in Perovskite Solar Cells},
  series = {Acs energy letters},
  volume    = {4},
  journal   = {Acs energy letters},
  number    = {12},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2380-8195},
  doi       = {10.1021/acsenergylett.9b02262},
  pages     = {2887 -- 2892},
  year      = {2019},
  abstract  = {Optimizing the photoluminescence (PL) yield of a solar cell has long been recognized as a key principle to maximize the power conversion efficiency. While PL measurements are routinely applied to perovskite films and solar cells under open circuit conditions (V-OC), it remains unclear how the emission depends on the applied voltage. Here, we performed PL(V) measurements on perovskite cells with different hole transport layer thicknesses and doping concentrations, resulting in remarkably different fill factors (FFs). The results reveal that PL(V) mirrors the current-voltage (JV) characteristics in the power-generating regime, which highlights an interesting correlation between radiative and nonradiative recombination losses. In particular, high FF devices show a rapid quenching of PL(V) from open-circuit to the maximum power point. We conclude that, while the PL has to be maximized at V-OC at lower biases < V-OC the PL must be rapidly quenched as charges need to be extracted prior to recombination.},
  language  = {en}
}
@article{LeCorreStolterfohtPerdigonToroetal.2019,
  author    = {Le Corre, Vincent M. and Stolterfoht, Martin and Perdig{\´o}n-Toro, Lorena and Feuerstein, Markus and Wolff, Christian Michael and Gil-Escrig, Lidon and Bolink, Henk J. and Neher, Dieter and Koster, L. Jan Anton},
  title     = {Charge Transport Layers Limiting the Efficiency of Perovskite Solar Cells: How To Optimize Conductivity, Doping, and Thickness},
  series = {ACS Applied Energy Materials},
  volume    = {2},
  journal   = {ACS Applied Energy Materials},
  number    = {9},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2574-0962},
  doi       = {10.1021/acsaem.9b00856},
  pages     = {6280 -- 6287},
  year      = {2019},
  abstract  = {Perovskite solar cells (PSCs) are one of the main research topics of the photovoltaic community; with efficiencies now reaching up to 24\%, PSCs are on the way to catching up with classical inorganic solar cells. However, PSCs have not yet reached their full potential. In fact, their efficiency is still limited by nonradiative recombination, mainly via trap-states and by losses due to the poor transport properties of the commonly used transport layers (TLs). Indeed, state-of-the-art TLs (especially if organic) suffer from rather low mobilities, typically within 10(-5) and 10(-2) cm(-2) V-1 s(-1), when compared to the high mobilities, 1-10 cm(-2) V-1 s(-1), measured for perovskites. This work presents a comprehensive analysis of the effect of the mobility, thickness, and doping density of the transport layers based on combined experimental and modeling results of two sets of devices made of a solution-processed high-performing triple-cation (PCE approximate to 20\%). The results are also cross-checked on vacuum-processed MAPbI(3) devices. From this analysis, general guidelines on how to optimize a TL are introduced and especially a new and simple formula to easily calculate the amount of doping necessary to counterbalance the low mobility of the TLs.},
  language  = {en}
}