@phdthesis{Lontsi2016, author = {Lontsi, Agostiny Marrios}, title = {1D shallow sedimentary subsurface imaging using ambient noise and active seismic data}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-103807}, school = {Universit{\"a}t Potsdam}, pages = {xix, 119}, year = {2016}, abstract = {The Earth's shallow subsurface with sedimentary cover acts as a waveguide to any incoming wavefield. Within the framework of my thesis, I focused on the characterization of this shallow subsurface within tens to few hundreds of meters of sediment cover. I imaged the seismic 1D shear wave velocity (and possibly the 1D compressional wave velocity). This information is not only required for any seismic risk assessment, geotechnical engineering or microzonation activities, but also for exploration and global seismology where site effects are often neglected in seismic waveform modeling. First, the conventional frequency-wavenumber (f - k) technique is used to derive the dispersion characteristic of the propagating surface waves recorded using distinct arrays of seismometers in 1D and 2D configurations. Further, the cross-correlation technique is applied to seismic array data to estimate the Green's function between receivers pairs combination assuming one is the source and the other the receiver. With the consideration of a 1D media, the estimated cross-correlation Green's functions are sorted with interstation distance in a virtual 1D active seismic experiment. The f - k technique is then used to estimate the dispersion curves. This integrated analysis is important for the interpretation of a large bandwidth of the phase velocity dispersion curves and therefore improving the resolution of the estimated 1D Vs profile. Second, the new theoretical approach based on the Diffuse Field Assumption (DFA) is used for the interpretation of the observed microtremors H/V spectral ratio. The theory is further extended in this research work to include not only the interpretation of the H/V measured at the surface, but also the H/V measured at depths and in marine environments. A modeling and inversion of synthetic H/V spectral ratio curves on simple predefined geological structures shows an almost perfect recovery of the model parameters (mainly Vs and to a lesser extent Vp). These results are obtained after information from a receiver at depth has been considered in the inversion. Finally, the Rayleigh wave phase velocity information, estimated from array data, and the H/V(z, f) spectral ratio, estimated from a single station data, are combined and inverted for the velocity profile information. Obtained results indicate an improved depth resolution in comparison to estimations using the phase velocity dispersion curves only. The overall estimated sediment thickness is comparable to estimations obtained by inverting the full micortremor H/V spectral ratio.}, language = {en} } @misc{Hennemann2016, author = {Hennemann, Anja}, title = {A cognitive-constructionist approach to Spanish creo {\O} and creo yo '[I] think'}, series = {Postprints der Universit{\"a}t Potsdam : Philosophische Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Philosophische Reihe}, number = {121}, issn = {1866-8380}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-397485}, pages = {26}, year = {2016}, abstract = {The present study approaches the Spanish postposed constructions creo {\O} and creo yo '[p], [I] think' from a cognitive-constructionist perspective. It is argued that both constructions are to be distinguished from one another because creo {\O} has a subjective function, while in creo yo, it is the intersubjective dimension that is particularly prominent. The present investigation takes both a qualitative and a quantitative perspective. With regard to the latter, the problem of quantitative representativity is addressed. The discussion posed the question of how empirical research can feed back into theory, more precisely, into the framework of Cognitive Construction Grammar. The data to be analyzed here are retrieved from the corpora Corpus de Referencia del Espa{\~n}ol Actual and Corpus del Espa{\~n}ol.}, language = {en} } @article{Dulgheru2016, author = {Dulgheru, Elena}, title = {A Conjunction of Mysteries}, series = {Andrej Tarkovskij: Klassiker - Классик - Classic - Classico : Beitr{\"a}ge zum internationalen Tarkovskij-Symposium an der Universit{\"a}t Potsdam ; Band 1}, journal = {Andrej Tarkovskij: Klassiker - Классик - Classic - Classico : Beitr{\"a}ge zum internationalen Tarkovskij-Symposium an der Universit{\"a}t Potsdam ; Band 1}, publisher = {Universit{\"a}t Potsdam}, address = {Potsdam}, isbn = {978-3-86956-351-0}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-95594}, pages = {201 -- 214}, year = {2016}, language = {en} } @misc{EhlertHolzweberLippitzetal.2016, author = {Ehlert, Christopher and Holzweber, Markus and Lippitz, Andreas and Unger, Wolfgang E. S. and Saalfrank, Peter}, title = {A detailed assignment of NEXAFS resonances of imidazolium based ionic liquids}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-394417}, pages = {8654 -- 8661}, year = {2016}, abstract = {In Near Edge X-Ray Absorption Fine Structure (NEXAFS) spectroscopy X-Ray photons are used to excite tightly bound core electrons to low-lying unoccupied orbitals of the system. This technique offers insight into the electronic structure of the system as well as useful structural information. In this work, we apply NEXAFS to two kinds of imidazolium based ionic liquids ([CnC1im]+[NTf2]- and [C4C1im]+[I]-). A combination of measurements and quantum chemical calculations of C K and N K NEXAFS resonances is presented. The simulations, based on the transition potential density functional theory method (TP-DFT), reproduce all characteristic features observed by the experiment. Furthermore, a detailed assignment of resonance features to excitation centers (carbon or nitrogen atoms) leads to a consistent interpretation of the spectra.}, language = {en} } @misc{MaoNakamuraViottietal.2016, author = {Mao, Hailiang and Nakamura, Moritaka and Viotti, Corrado and Grebe, Markus}, title = {A framework for lateral membrane trafficking and polar tethering of the PEN3 ATP-Binding cassette transporter}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, number = {909}, issn = {1866-8372}, doi = {10.25932/publishup-44130}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-441302}, pages = {2245 -- 2260}, year = {2016}, abstract = {The outermost cell layer of plants, the epidermis, and its outer (lateral) membrane domain facing the environment are continuously challenged by biotic and abiotic stresses. Therefore, the epidermis and the outer membrane domain provide important selective and protective barriers. However, only a small number of specifically outer membrane-localized proteins are known. Similarly, molecular mechanisms underlying the trafficking and the polar placement of outer membrane domain proteins require further exploration. Here, we demonstrate that ACTIN7 (ACT7) mediates trafficking of the PENETRATION3 (PEN3) outer membrane protein from the trans-Golgi network (TGN) to the plasma membrane in the root epidermis of Arabidopsis (Arabidopsis thaliana) and that actin function contributes to PEN3 endocytic recycling. In contrast to such generic ACT7-dependent trafficking from the TGN, the EXOCYST84b (EXO84b) tethering factor mediates PEN3 outer-membrane polarity. Moreover, precise EXO84b placement at the outer membrane domain itself requires ACT7 function. Hence, our results uncover spatially and mechanistically distinct requirements for ACT7 function during outer lateral membrane cargo trafficking and polarity establishment. They further identify an exocyst tethering complex mediator of outer lateral membrane cargo polarity.}, language = {en} } @misc{LiaimerJensenDittmannThuenemann2016, author = {Liaimer, Anton and Jensen, John B. and Dittmann-Th{\"u}nemann, Elke}, title = {A genetic and chemical perspective on symbiotic recruitment of cyanobacteria of the genus Nostoc into the host plant Blasia pusilla L.}, series = {Frontiers in microbiology}, journal = {Frontiers in microbiology}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-407179}, pages = {16}, year = {2016}, abstract = {Liverwort Blasia pusilla L. recruits soil nitrogen-fixing cyanobacteria of genus Nostoc as symbiotic partners. In this work we compared Nostoc community composition inside the plants and in the soil around them from two distant locations in Northern Norway. STRR fingerprinting and 16S rDNA phylogeny reconstruction showed a remarkable local diversity among isolates assigned to several Nostoc clades. An extensive web of negative allelopathic interactions was recorded at an agricultural site, but not at the undisturbed natural site. The cell extracts of the cyanobacteria did not show antimicrobial activities, but four isolates were shown to be cytotoxic to human cells. The secondary metabolite profiles of the isolates were mapped by MALDI-TOF MS, and the most prominent ions were further analyzed by Q-TOF for MS/MS aided identification. Symbiotic isolates produced a great variety of small peptide-like substances, most of which lack any record in the databases. Among identified compounds we found microcystin and nodularin variants toxic to eukaryotic cells. Microcystin producing chemotypes were dominating as symbiotic recruits but not in the free-living community. In addition, we were able to identify several novel aeruginosins and banyaside-like compounds, as well as nostocyclopeptides and nosperin.}, language = {en} } @unpublished{AlsaedyTarkhanov2016, author = {Alsaedy, Ammar and Tarkhanov, Nikolai Nikolaevich}, title = {A Hilbert boundary value problem for generalised Cauchy-Riemann equations}, volume = {5}, number = {1}, publisher = {Universit{\"a}tsverlag Potsdam}, address = {Potsdam}, issn = {2193-6943}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-86109}, pages = {21}, year = {2016}, abstract = {We elaborate a boundary Fourier method for studying an analogue of the Hilbert problem for analytic functions within the framework of generalised Cauchy-Riemann equations. The boundary value problem need not satisfy the Shapiro-Lopatinskij condition and so it fails to be Fredholm in Sobolev spaces. We show a solvability condition of the Hilbert problem, which looks like those for ill-posed problems, and construct an explicit formula for approximate solutions.}, language = {en} } @misc{ClusellaPolitiRosenblum2016, author = {Clusella, Pau and Politi, Antonio and Rosenblum, Michael}, title = {A minimal model of self-consistent partial synchrony}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch Naturwissenschaftliche Reihe}, number = {890}, issn = {1866-8372}, doi = {10.25932/publishup-43626}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-436266}, pages = {19}, year = {2016}, abstract = {We show that self-consistent partial synchrony in globally coupled oscillatory ensembles is a general phenomenon. We analyze in detail appearance and stability properties of this state in possibly the simplest setup of a biharmonic Kuramoto-Daido phase model as well as demonstrate the effect in limit-cycle relaxational Rayleigh oscillators. Such a regime extends the notion of splay state from a uniform distribution of phases to an oscillating one. Suitable collective observables such as the Kuramoto order parameter allow detecting the presence of an inhomogeneous distribution. The characteristic and most peculiar property of self-consistent partial synchrony is the difference between the frequency of single units and that of the macroscopic field.}, language = {en} } @misc{KrupinskiBozorgLarssonetal.2016, author = {Krupinski, Pawel and Bozorg, Behruz and Larsson, Andr{\´e} and Pietra, Stefano and Grebe, Markus and J{\"o}nsson, Henrik}, title = {A model analysis of mechanisms for radial microtubular patterns at root hair initiation sites}, series = {Frontiers in plant science}, journal = {Frontiers in plant science}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-407181}, pages = {12}, year = {2016}, abstract = {Plant cells have two main modes of growth generating anisotropic structures. Diffuse growth where whole cell walls extend in specific directions, guided by anisotropically positioned cellulose fibers, and tip growth, with inhomogeneous addition of new cell wall material at the tip of the structure. Cells are known to regulate these processes via molecular signals and the cytoskeleton. Mechanical stress has been proposed to provide an input to the positioning of the cellulose fibers via cortical microtubules in diffuse growth. In particular, a stress feedback model predicts a circumferential pattern of fibers surrounding apical tissues and growing primordia, guided by the anisotropic curvature in such tissues. In contrast, during the initiation of tip growing root hairs, a star-like radial pattern has recently been observed. Here, we use detailed finite element models to analyze how a change in mechanical properties at the root hair initiation site can lead to star-like stress patterns in order to understand whether a stress-based feedback model can also explain the microtubule patterns seen during root hair initiation. We show that two independent mechanisms, individually or combined, can be sufficient to generate radial patterns. In the first, new material is added locally at the position of the root hair. In the second, increased tension in the initiation area provides a mechanism. Finally, we describe how a molecular model of Rho-of-plant (ROP) GTPases activation driven by auxin can position a patch of activated ROP protein basally along a 2D root epidermal cell plasma membrane, paving the way for models where mechanical and molecular mechanisms cooperate in the initial placement and outgrowth of root hairs.}, language = {en} } @misc{ZieglerHeidbachReineckeretal.2016, author = {Ziegler, Moritz O. and Heidbach, Oliver and Reinecker, John and Przybycin, Anna M. and Scheck-Wenderoth, Magdalena}, title = {A multi-stage 3-D stress field modelling approach exemplified in the Bavarian Molasse Basin}, series = {Postprints der Universit{\"a}t Potsdam Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam Mathematisch-Naturwissenschaftliche Reihe}, number = {556}, issn = {1866-8372}, doi = {10.25932/publishup-40980}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-409806}, pages = {18}, year = {2016}, abstract = {The knowledge of the contemporary in situ stress state is a key issue for safe and sustainable subsurface engineering. However, information on the orientation and magnitudes of the stress state is limited and often not available for the areas of interest. Therefore 3-D geomechanical-numerical modelling is used to estimate the in situ stress state and the distance of faults from failure for application in subsurface engineering. The main challenge in this approach is to bridge the gap in scale between the widely scattered data used for calibration of the model and the high resolution in the target area required for the application. We present a multi-stage 3-D geomechanical-numerical approach which provides a state-of-the-art model of the stress field for a reservoir-scale area from widely scattered data records. Therefore, we first use a large-scale regional model which is calibrated by available stress data and provides the full 3-D stress tensor at discrete points in the entire model volume. The modelled stress state is used subsequently for the calibration of a smaller-scale model located within the large-scale model in an area without any observed stress data records. We exemplify this approach with two-stages for the area around Munich in the German Molasse Basin. As an example of application, we estimate the scalar values for slip tendency and fracture potential from the model results as measures for the criticality of fault reactivation in the reservoir-scale model. The modelling results show that variations due to uncertainties in the input data are mainly introduced by the uncertain material properties and missing S-Hmax magnitude estimates needed for a more reliable model calibration. This leads to the conclusion that at this stage the model's reliability depends only on the amount and quality of available stress information rather than on the modelling technique itself or on local details of the model geometry. Any improvements in modelling and increases in model reliability can only be achieved using more high-quality data for calibration.}, language = {en} } @misc{NeherKniepertElimelechetal.2016, author = {Neher, Dieter and Kniepert, Juliane and Elimelech, Arik and Koster, L. Jan Anton}, title = {A New Figure of Merit for Organic Solar Cells with Transport-limited Photocurrents}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-91414}, pages = {9}, year = {2016}, abstract = {Compared to their inorganic counterparts, organic semiconductors suffer from relatively low charge carrier mobilities. Therefore, expressions derived for inorganic solar cells to correlate characteristic performance parameters to material properties are prone to fail when applied to organic devices. This is especially true for the classical Shockley-equation commonly used to describe current-voltage (JV)-curves, as it assumes a high electrical conductivity of the charge transporting material. Here, an analytical expression for the JV-curves of organic solar cells is derived based on a previously published analytical model. This expression, bearing a similar functional dependence as the Shockley-equation, delivers a new figure of merit α to express the balance between free charge recombination and extraction in low mobility photoactive materials. This figure of merit is shown to determine critical device parameters such as the apparent series resistance and the fill factor.}, language = {en} } @phdthesis{Falter2016, author = {Falter, Daniela}, title = {A novel approach for large-scale flood risk assessments}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-90239}, school = {Universit{\"a}t Potsdam}, pages = {95}, year = {2016}, abstract = {In the past, floods were basically managed by flood control mechanisms. The focus was set on the reduction of flood hazard. The potential consequences were of minor interest. Nowadays river flooding is increasingly seen from the risk perspective, including possible consequences. Moreover, the large-scale picture of flood risk became increasingly important for disaster management planning, national risk developments and the (re-) insurance industry. Therefore, it is widely accepted that risk-orientated flood management ap-proaches at the basin-scale are needed. However, large-scale flood risk assessment methods for areas of several 10,000 km² are still in early stages. Traditional flood risk assessments are performed reach wise, assuming constant probabilities for the entire reach or basin. This might be helpful on a local basis, but where large-scale patterns are important this approach is of limited use. Assuming a T-year flood (e.g. 100 years) for the entire river network is unrealistic and would lead to an overestimation of flood risk at the large scale. Due to the lack of damage data, additionally, the probability of peak discharge or rainfall is usually used as proxy for damage probability to derive flood risk. With a continuous and long term simulation of the entire flood risk chain, the spatial variability of probabilities could be consider and flood risk could be directly derived from damage data in a consistent way. The objective of this study is the development and application of a full flood risk chain, appropriate for the large scale and based on long term and continuous simulation. The novel approach of 'derived flood risk based on continuous simulations' is introduced, where the synthetic discharge time series is used as input into flood impact models and flood risk is directly derived from the resulting synthetic damage time series. The bottleneck at this scale is the hydrodynamic simu-lation. To find suitable hydrodynamic approaches for the large-scale a benchmark study with simplified 2D hydrodynamic models was performed. A raster-based approach with inertia formulation and a relatively high resolution of 100 m in combination with a fast 1D channel routing model was chosen. To investigate the suitability of the continuous simulation of a full flood risk chain for the large scale, all model parts were integrated into a new framework, the Regional Flood Model (RFM). RFM consists of the hydrological model SWIM, a 1D hydrodynamic river network model, a 2D raster based inundation model and the flood loss model FELMOps+r. Subsequently, the model chain was applied to the Elbe catchment, one of the largest catchments in Germany. For the proof-of-concept, a continuous simulation was per-formed for the period of 1990-2003. Results were evaluated / validated as far as possible with available observed data in this period. Although each model part introduced its own uncertainties, results and runtime were generally found to be adequate for the purpose of continuous simulation at the large catchment scale. Finally, RFM was applied to a meso-scale catchment in the east of Germany to firstly perform a flood risk assessment with the novel approach of 'derived flood risk assessment based on continuous simulations'. Therefore, RFM was driven by long term synthetic meteorological input data generated by a weather generator. Thereby, a virtual time series of climate data of 100 x 100 years was generated and served as input to RFM providing subsequent 100 x 100 years of spatially consistent river discharge series, inundation patterns and damage values. On this basis, flood risk curves and expected annual damage could be derived directly from damage data, providing a large-scale picture of flood risk. In contrast to traditional flood risk analysis, where homogenous return periods are assumed for the entire basin, the presented approach provides a coherent large-scale picture of flood risk. The spatial variability of occurrence probability is respected. Additionally, data and methods are consistent. Catchment and floodplain processes are repre-sented in a holistic way. Antecedent catchment conditions are implicitly taken into account, as well as physical processes like storage effects, flood attenuation or channel-floodplain interactions and related damage influencing effects. Finally, the simulation of a virtual period of 100 x 100 years and consequently large data set on flood loss events enabled the calculation of flood risk directly from damage distributions. Problems associated with the transfer of probabilities in rainfall or peak runoff to probabilities in damage, as often used in traditional approaches, are bypassed. RFM and the 'derived flood risk approach based on continuous simulations' has the potential to provide flood risk statements for national planning, re-insurance aspects or other questions where spatially consistent, large-scale assessments are required.}, language = {en} } @article{Salvestroni2016, author = {Salvestroni, Simonetta}, title = {A Recurring Theme in Tarkovsky's Cinema}, series = {Andrej Tarkovskij: Klassiker - Классик - Classic - Classico : Beitr{\"a}ge zum internationalen Tarkovskij-Symposium an der Universit{\"a}t Potsdam ; Band 2}, journal = {Andrej Tarkovskij: Klassiker - Классик - Classic - Classico : Beitr{\"a}ge zum internationalen Tarkovskij-Symposium an der Universit{\"a}t Potsdam ; Band 2}, publisher = {Universit{\"a}tsverlag Potsdam}, address = {Potsdam}, isbn = {978-3-86956-352-7}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-100472}, pages = {399 -- 407}, year = {2016}, language = {en} } @misc{LevermannWinkelmann2016, author = {Levermann, Anders and Winkelmann, Ricarda}, title = {A simple equation for the melt elevation feedback of ice sheets}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, number = {529}, issn = {1866-8372}, doi = {10.25932/publishup-40983}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-409834}, pages = {9}, year = {2016}, abstract = {In recent decades, the Greenland Ice Sheet has been losing mass and has thereby contributed to global sea-level rise. The rate of ice loss is highly relevant for coastal protection worldwide. The ice loss is likely to increase under future warming. Beyond a critical temperature threshold, a meltdown of the Greenland Ice Sheet is induced by the self-enforcing feedback between its lowering surface elevation and its increasing surface mass loss: the more ice that is lost, the lower the ice surface and the warmer the surface air temperature, which fosters further melting and ice loss. The computation of this rate so far relies on complex numerical models which are the appropriate tools for capturing the complexity of the problem. By contrast we aim here at gaining a conceptual understanding by deriving a purposefully simple equation for the self-enforcing feedback which is then used to estimate the melt time for different levels of warming using three observable characteristics of the ice sheet itself and its surroundings. The analysis is purely conceptual in nature. It is missing important processes like ice dynamics for it to be useful for applications to sea-level rise on centennial timescales, but if the volume loss is dominated by the feedback, the resulting logarithmic equation unifies existing numerical simulations and shows that the melt time depends strongly on the level of warming with a critical slow-down near the threshold: the median time to lose 10\% of the present-day ice volume varies between about 3500 years for a temperature level of 0.5 degrees C above the threshold and 500 years for 5 degrees C. Unless future observations show a significantly higher melting sensitivity than currently observed, a complete meltdown is unlikely within the next 2000 years without significant ice-dynamical contributions.}, language = {en} } @misc{Wack2016, type = {Master Thesis}, author = {Wack, Christian}, title = {Acceptance criteria as part of the German energy turnaround}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-395173}, school = {Universit{\"a}t Potsdam}, pages = {88}, year = {2016}, abstract = {Die vorliegende Arbeit ist eine Fallstudie zum Netzausbauprojekt „Suedlink". Sie gliedert sich demnach in vier wesentliche Abschnitte: 1. In einem theoretischen Teil werden die f{\"u}r diese Arbeit wichtigen Theorien der „Sozialen Akzeptanz" nach W{\"u}stenhagen et al. (2007), der „Schritte der Partizipation" nach M{\"u}nnich (2014) und der Governance-Theorie nach Benz und Dose (2011) erl{\"a}utert. 2. In einem methodischen Teil werden die f{\"u}r diese Arbeit relevanten Methoden diskutiert und kritisch erl{\"a}utert. 3. In einem qualitativ-empirischen Teil werden die Informationen der Experteninterviews ausgewertet und anhand der vorgestellten Theorien eingeordnet. In dem vierten und letzten Teil der Arbeit wird eine empirisch-quantitative Analyse der gesellschaftlichen Akzeptanz gegen{\"u}ber S{\"u}dlink vorgenommen. In dieser Arbeit soll mithilfe qualitativer und quantitativer Methoden zwei Fragen gekl{\"a}rt werden. 1. Welche Governance-Aspekte waren f{\"u}r eine gesetzliche Priorit{\"a}t von Erdkabeln im Ausbau von Hochspannungs{\"u}bertragungsgleichstromleitungen entscheidend? Hierf{\"u}r wurden intensive Dokumentenanalysen und verschiedene Experteninterviews durchgef{\"u}hrt. 2. Die zentrale Fragestellung dieser Arbeit besch{\"a}ftigt sich mit der Frage, inwiefern lokale und individuelle Faktoren die Akzeptanz von Suedlink beeinflussen. Hierbei ist interessant zu sehen, welchen Einfluss der gesetzliche Erdkabelvorrang bei der Akzeptanzbildung der Bev{\"o}lkerung gegen{\"u}ber Suedlink gespielt hat. F{\"u}r die Beantwortung wurde ein Online-survey konzipiert, welcher zwischen M{\"a}rz und Juli 2016 {\"u}ber B{\"u}rgerinitiativen, Landr{\"a}te und soziale Netzwerke verteilt wurde. Nach Abschluss der Datenerhebung wurden dieser unter Verwendung deskriptiv-quantitativer Methoden ausgewertet. Die Auswertung der Umfrage zeigt auf, das Erdkabel alleine keine nennenswerte Akzeptanz schaffen (vgl. dazu Menges und Beyer, 2013). Vielmehr stehen individuell und lokale Faktoren und Kriterien im Vordergrund der Beurteilung. Zum Beispiel spielt die Qualit{\"a}t der Partizipation und Einbindung der B{\"u}rger sowie die N{\"a}he zur Erdverkabelung und die finanzielle Mehrbelastung eine Rolle bei der Beurteilung von Erdkabeln. Zudem wird deutlich, das Befragte aus B{\"u}rgerinitiativen wesentlich kritischer gegen Suedlink allgemein und gegen{\"u}ber Erdkabeln im speziellen sind. Ferner ist signifikant, dass Eigenheimbesitzer jegliche Bauform ablehnen.}, language = {en} } @misc{BonacheGonzalezMendezKrahe2016, author = {Bonache, Helena and Gonzalez-Mendez, Rosaura and Krah{\´e}, Barbara}, title = {Adult attachment styles, destructive conflict resolution, and the experience of intimate partner violence}, series = {Postprints der Universit{\"a}t Potsdam : Humanwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Humanwissenschaftliche Reihe}, number = {405}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-405132}, pages = {23}, year = {2016}, abstract = {Although there is ample evidence linking insecure attachment styles and intimate partner violence (IPV), little is known about the psychological processes underlying this association, especially from the victim's perspective. The present study examined how attachment styles relate to the experience of sexual and psychological abuse, directly or indirectly through destructive conflict resolution strategies, both self-reported and attributed to their opposite-sex romantic partner. In an online survey, 216 Spanish undergraduates completed measures of adult attachment style, engagement and withdrawal conflict resolution styles shown by self and partner, and victimization by an intimate partner in the form of sexual coercion and psychological abuse. As predicted, anxious and avoidant attachment styles were directly related to both forms of victimization. Also, an indirect path from anxious attachment to IPV victimization was detected via destructive conflict resolution strategies. Specifically, anxiously attached participants reported a higher use of conflict engagement by themselves and by their partners. In addition, engagement reported by the self and perceived in the partner was linked to an increased probability of experiencing sexual coercion and psychological abuse. Avoidant attachment was linked to higher withdrawal in conflict situations, but the paths from withdrawal to perceived partner engagement, sexual coercion, and psychological abuse were non-significant. No gender differences in the associations were found. The discussion highlights the role of anxious attachment in understanding escalating patterns of destructive conflict resolution strategies, which may increase the vulnerability to IPV victimization.}, language = {en} } @techreport{Kahombo2016, type = {Working Paper}, author = {Kahombo, Balingene}, title = {Africa Within the Justice System of the International Criminal Court}, series = {KFG Working Paper Series}, journal = {KFG Working Paper Series}, number = {2}, issn = {2509-3770}, doi = {10.25932/publishup-41953}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-419537}, pages = {42}, year = {2016}, abstract = {This article re-examines the relationship between Africa and the International Criminal Court (ICC). It traces the successive changes of the African attitude towards this Court, from states' euphoria, to hostility against its work, to regional counter-initiatives through the umbrella of the African Union (AU). The main argument goes beyond the idea of "the Court that Africa wants" in order to identify concrete reasons behind such a formal argument which may have fostered, if not enticed, the majority of African states to become ICC members and actively cooperate with it, when paradoxically some great powers have decided to stay outside its jurisdiction. It also seeks to understand, from a political and legal viewpoint, which parameters have changed since then to provoke that hostile attitude against the Court's work and the entrance of the AU into the debate through the African Common Position on the ICC. Lastly, this article explores African alternatives to the contested ICC justice system. It examines the need to reform the Rome Statute in order to give more independence, credibility and legitimacy to the ICC and its duplication to some extent by the new "Criminal Court of the African Union". Particular attention is paid to the resistance against this idea to reform the ICC justice system.}, language = {en} } @phdthesis{Raeling2016, author = {R{\"a}ling, Romy}, title = {Age of acquisition and semantic typicality effects}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-95943}, school = {Universit{\"a}t Potsdam}, pages = {x, 133}, year = {2016}, abstract = {Age of acquisition (AOA) is a psycholinguistic variable that significantly influences behavioural measures (response times and accuracy rates) in tasks that require lexical and semantic processing. Its origin is - unlike the origin of semantic typicality (TYP), which is assumed at the semantic level - controversially discussed. Different theories propose AOA effects to originate either at the semantic level or at the link between semantics and phonology (lemma-level). The dissertation aims at investigating the influence of AOA and its interdependence with the semantic variable TYP on particularly semantic processing in order to pinpoint the origin of AOA effects. Therefore, three studies have been conducted that considered the variables AOA and TYP in semantic processing tasks (category verifications and animacy decisions) by means of behavioural and partly electrophysiological (ERP) data and in different populations (healthy young and elderly participants and in semantically impaired individuals with aphasia (IWA)). The behavioural and electrophysiological data of the three studies provide evidence for distinct processing levels of the variables AOA and TYP. The data further support previous assumptions on a semantic origin for TYP but question the same for AOA. The findings, however, support an origin of AOA effects at the transition between the word form (phonology) and the semantic level that can be captured at the behavioural but not at the electrophysiological level.}, language = {en} } @misc{KuikLauerChurkinaetal.2016, author = {Kuik, Friderike and Lauer, Axel and Churkina, Galina and Denier Van der Gon, Hugo Anne Cornelis and Fenner, Daniel and Mar, Kathleen A. and Butler, Tim M.}, title = {Air quality modelling in the Berlin-Brandenburg region using WRF-Chem v3.7.1}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, number = {531}, issn = {1866-8372}, doi = {10.25932/publishup-41013}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-410131}, pages = {25}, year = {2016}, abstract = {Air pollution is the number one environmental cause of premature deaths in Europe. Despite extensive regulations, air pollution remains a challenge, especially in urban areas. For studying summertime air quality in the Berlin-Brandenburg region of Germany, the Weather Research and Forecasting Model with Chemistry (WRF-Chem) is set up and evaluated against meteorological and air quality observations from monitoring stations as well as from a field campaign conducted in 2014. The objective is to assess which resolution and level of detail in the input data is needed for simulating urban background air pollutant concentrations and their spatial distribution in the Berlin-Brandenburg area. The model setup includes three nested domains with horizontal resolutions of 15, 3 and 1 km and anthropogenic emissions from the TNO-MACC III inventory. We use RADM2 chemistry and the MADE/SORGAM aerosol scheme. Three sensitivity simulations are conducted updating input parameters to the single-layer urban canopy model based on structural data for Berlin, specifying land use classes on a sub-grid scale (mosaic option) and downscaling the original emissions to a resolution of ca. 1 km x 1 km for Berlin based on proxy data including traffic density and population density. The results show that the model simulates meteorology well, though urban 2m temperature and urban wind speeds are biased high and nighttime mixing layer height is biased low in the base run with the settings described above. We show that the simulation of urban meteorology can be improved when specifying the input parameters to the urban model, and to a lesser extent when using the mosaic option. On average, ozone is simulated reasonably well, but maximum daily 8 h mean concentrations are underestimated, which is consistent with the results from previous modelling studies using the RADM2 chemical mechanism. Particulate matter is underestimated, which is partly due to an underestimation of secondary organic aerosols. NOx (NO + NO2) concentrations are simulated reasonably well on average, but nighttime concentrations are overestimated due to the model's underestimation of the mixing layer height, and urban daytime concentrations are underestimated. The daytime underestimation is improved when using downscaled, and thus locally higher emissions, suggesting that part of this bias is due to deficiencies in the emission input data and their resolution. The results further demonstrate that a horizontal resolution of 3 km improves the results and spatial representativeness of the model compared to a horizontal resolution of 15 km. With the input data (land use classes, emissions) at the level of detail of the base run of this study, we find that a horizontal resolution of 1 km does not improve the results compared to a resolution of 3 km. However, our results suggest that a 1 km horizontal model resolution could enable a detailed simulation of local pollution patterns in the Berlin-Brandenburg region if the urban land use classes, together with the respective input parameters to the urban canopy model, are specified with a higher level of detail and if urban emissions of higher spatial resolution are used.}, language = {en} } @phdthesis{Steeples2016, author = {Steeples, Elliot}, title = {Amino acid-derived imidazolium salts: platform molecules for N-Heterocyclic carbene metal complexes and organosilica materials}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-101861}, school = {Universit{\"a}t Potsdam}, pages = {139}, year = {2016}, abstract = {In the interest of producing functional catalysts from sustainable building-blocks, 1, 3-dicarboxylate imidazolium salts derived from amino acids were successfully modified to be suitable as N-Heterocyclic carbene (NHC) ligands within metal complexes. Complexes of Ag(I), Pd(II), and Ir(I) were successfully produced using known procedures using ligands derived from glycine, alanine, β-alanine and phenylalanine. The complexes were characterized in solid state using X-Ray crystallography, which allowed for the steric and electronic comparison of these ligands to well-known NHC ligands within analogous metal complexes. The palladium complexes were tested as catalysts for aqueous-phase Suzuki-Miyaura cross-coupling. Water-solubility could be induced via ester hydrolysis of the N-bound groups in the presence of base. The mono-NHC-Pd complexes were seen to be highly active in the coupling of aryl bromides with phenylboronic acid; the active catalyst of which was determined to be mostly Pd(0) nanoparticles. Kinetic studies determined that reaction proceeds quickly in the coupling of bromoacetophenone, for both pre-hydrolyzed and in-situ hydrolysis catalyst dissolution. The catalyst could also be recycled for an extra run by simply re-using the aqueous layer. The imidazolium salts were also used to produce organosilica hybrid materials. This was attempted via two methods: by post-grafting onto a commercial organosilica, and co-condensation of the corresponding organosilane. The co-condensation technique harbours potential for the production of solid-support catalysts.}, language = {en} }