@article{AlSa'diJaiserBagnichetal.2012,
  author    = {Al-Sa'di, Mahmoud and Jaiser, Frank and Bagnich, Sergey A. and Unger, Thomas and Blakesley, James C. and Wilke, Andreas and Neher, Dieter},
  title     = {Electrical and optical simulations of a polymer-based phosphorescent organic light-emitting diode with high efficiency},
  series = {Journal of polymer science : B, Polymer physics},
  volume    = {50},
  journal   = {Journal of polymer science : B, Polymer physics},
  number    = {22},
  publisher = {Wiley-Blackwell},
  address   = {Hoboken},
  issn      = {0887-6266},
  doi       = {10.1002/polb.23158},
  pages     = {1567 -- 1576},
  year      = {2012},
  abstract  = {A comprehensive numerical device simulation of the electrical and optical characteristics accompanied with experimental measurements of a new highly efficient system for polymer-based light-emitting diodes doped with phosphorescent dyes is presented. The system under investigation comprises an electron transporter attached to a polymer backbone blended with an electronically inert small molecule and an iridium-based green phosphorescent dye which serves as both emitter and hole transporter. The device simulation combines an electrical and an optical model. Based on the known highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels of all components as well as the measured electrical and optical characteristics of the devices, we model the emissive layer as an effective medium using the dye's HOMO as hole transport level and the polymer LUMO as electron transport level. By fine-tuning the injection barriers at the electron and hole-injecting contact, respectively, in simulated devices, unipolar device characteristics were fitted to the experimental data. Simulations using the so-obtained set of parameters yielded very good agreement to the measured currentvoltage, luminancevoltage characteristics, and the emission profile of entire bipolar light-emitting diodes, without additional fitting parameters. The simulation was used to gain insight into the physical processes and the mechanisms governing the efficiency of the organic light-emitting diode, including the position and extent of the recombination zone, carrier concentration profiles, and field distribution inside the device. The simulations show that the device is severely limited by hole injection, and that a reduction of the hole-injection barrier would improve the device efficiency by almost 50\%.},
  language  = {en}
}
@article{ProctorKimNeheretal.2013,
  author    = {Proctor, Christopher M. and Kim, Chunki and Neher, Dieter and Thuc-Quyen Nguyen,},
  title     = {Nongeminate recombination and charge transport limitations in diketopyrrolopyrrole-based solution-processed small molecule solar cells},
  series = {Advanced functional materials},
  volume    = {23},
  journal   = {Advanced functional materials},
  number    = {28},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1616-301X},
  doi       = {10.1002/adfm.201202643},
  pages     = {3584 -- 3594},
  year      = {2013},
  abstract  = {Charge transport and nongeminate recombination are investigated in two solution-processed small molecule bulk heterojunction solar cells consisting of diketopyrrolopyrrole (DPP)-based donor molecules, mono-DPP and bis-DPP, blended with [6,6]-phenyl-C71-butyric acid methyl ester (PCBM). While the bis-DPP system exhibits a high fill factor (62\%) the mono-DPP system suffers from pronounced voltage dependent losses, which limit both the fill factor (46\%) and short circuit current. A method to determine the average charge carrier density, recombination current, and effective carrier lifetime in operating solar cells as a function of applied bias is demonstrated. These results and light intensity measurements of the current-voltage characteristics indicate that the mono-DPP system is severely limited by nongeminate recombination losses. Further analysis reveals that the most significant factor leading to the difference in fill factor is the comparatively poor hole transport properties in the mono-DPP system (2 x 10(-5) cm(2) V-1 s(-1) versus 34 x 10(-5) cm(2) V-1 s(-1)). These results suggest that future design of donor molecules for organic photovoltaics should aim to increase charge carrier mobility thereby enabling faster sweep out of charge carriers before they are lost to nongeminate recombination.},
  language  = {en}
}