@article{YanFangNoecheletal.2015,
  author    = {Yan, Wan and Fang, Liang and N{\"o}chel, Ulrich and Kratz, Karl and Lendlein, Andreas},
  title     = {Influence of deformation temperature on structural variation and shape-memory effect of a thermoplastic semi-crystalline multiblock copolymer},
  series = {eXPRESS polymer letters},
  volume    = {9},
  journal   = {eXPRESS polymer letters},
  number    = {7},
  publisher = {Budapest University of Technology and Economics, Department of Polymer Engineering},
  address   = {Budapest},
  issn      = {1788-618X},
  doi       = {10.3144/expresspolymlett.2015.58},
  pages     = {624 -- 635},
  year      = {2015},
  abstract  = {A multiblock copolymer termed as PCL-PIBMD, consisting of crystallizable poly(epsilon-caprolactone) (PCL) segments and crystallizable poly(3S-isobutyl-morpholine-2,5-dione) (PIBMD) segments, has been reported as a material showing a thermally-induced shape-memory effect. While PIBMD crystalline domains act as netpoints to determine the permanent shape, both PCL crystalline domains and PIBMD amorphous domains, which have similar transition temperatures (T-trans) can act as switching domains. In this work, the influence of the deformation temperature (T-deform = 50 or 20 degrees C), which was above or below T-trans, on the structural changes of PCL-PIBMD during uniaxial deformation and the shapememory properties were investigated. Furthermore, the relative contribution of crystalline PCL and PIBMD amorphous phases to the fixation of the temporary shape were distinguished by a toluene vapor treatment approach. The results indicated that at 50 degrees C, both PCL and PIBMD amorphous phases can be orientated during deformation, resulting in thermally-induced crystals of PCL domains and joint contribution to the switching domains. In contrast at 20 degrees C, the temporary shape was mainly fixed by PCL crystals generated via strain-induced crystallization.},
  language  = {en}
}
@phdthesis{Wang2018,
  author    = {Wang, Li},
  title     = {Reprogrammable, magnetically controlled polymer actuators},
  school      = {Universit{\"a}t Potsdam},
  pages     = {xxviii, 107},
  year      = {2018},
  abstract  = {Polymeric materials, which can perform reversible shape changes after programming, in response to a thermal or electrical stimulation, can serve as (soft) actuating components in devices like artificial muscles, photonics, robotics or sensors. Such polymeric actuators can be realized with hydrogels, liquid crystalline elastomers, electro-active polymers or shape-memory polymers by controlling with stumuli such as heat, light, electrostatic or magnetic field. If the application conditions do not allow the direct heating or electric stimulation of these smart devices, noncontact triggering will be required. Remotely controlled actuation have been reported for liquid crystalline elastomer composites or shape-memory polymer network composites, when a persistent external stress is applied during inductive heating in an alternating magnetic field. However such composites cannot meet the demands of applications requiring remotely controlled free-standing motions of the actuating components. The current thesis investigates, whether a reprogrammable remotely controlled soft actuator can be realized by magneto-sensitive multiphase shape-memory copolymer network composites containing magnetite nanoparticles as magneto-sensitive multivalent netpoints. A central hypothesis was that a magnetically controlled two-way (reversible bidirectional) shape-memory effect in such nanocomposites can be achieved without application of external stress (freestanding), when the required orientation of the crystallizable actuation domains (ADs) can be ensured by an internal skeleton like structure formed by a second crystallizable phase determing the samples´s geometry, while magneto-sensitive iron oxide nanoparticles covalently integrated in the ADs allow remote temperature control. The polymer matrix of these composites should exhibit a phase-segregated morphology mainly composed of cyrstallizable ADs, whereby a second set of higher melting crystallites can take a skeleton like, geometry determining function (geometry determining domains, GDs) after programming of the composite and in this way the orientation of the ADs is established and maintained during actuation. The working principle for the reversible bidirectional movements in the multiphase shape-memory polymer network composite is related to a melting-induced contraction (MIC) during inductive heating and the crystallization induced elongation (CIE) of the oriented ADs during cooling. Finally, the amount of multivalent magnetosensitive netpoints in such a material should be as low as possible to ensure an adequate overall elasticity of the nanocomposite and at the same time a complete melting of both ADs and GDs via inductive heating, which is mandatory for enabling reprogrammability. At first, surface decorated iron oxide nanoparticles were synthesized and investigated. The coprecipitation method was applied to synthesize magnetic nanoparticles (mNPs) based on magnetite with size of 12±3 nm and in a next step a ring-opening polymerization (ROP) was utilized for covalent surface modification of such mNPs with oligo(ϵ-caprolactone) (OCL) or oligo(ω-pentadecalactone) (OPDL) via the "grafting from" approach. A successful coating of mNPs with OCL and OPDL was confirmed by differential scanning calorimetry (DSC) experiments showing melting peaks at 52±1 °C for mNP-OCL and 89±1 °C for mNP-OPDL. It was further explored whether two-layered surface decorated mNPs, can be prepared via a second surface-initiated ROP of mNP-OCL or mNP-OPDL with ω-pentadecalactone or ϵ-caprolactone. The observation of two distinct melting transitions in DSC experiments as well as the increase in molecular weight of the detached coatings determined by GPC and 1H-NMR indicated a successful synthesis of the twolayered nanoparticles mNP-OCL-OPDL and mNP-OPDL-OCL. In contrast TEM micrographs revealed a reduction of the thickness of the polymeric coating on the nanoparticles after the second ROP, indicating that the applied synthesis and purification required further optimization. For evaluating the impact of the dispersion of mNPs within a polymer matrix on the resulting inductive heating capability of composites, plain mNPs as well as OCL coated magnetite nanoparticles (mNP-OCLs) were physically incorporated into crosslinked poly(ε-caprolactone) (PCL) networks. Inductive heating experiments were performed with both networks cPCL/mNP and cPCL/mNP-OCL in an alternating magnetic field (AMF) with a magnetic field strength of H = 30 kA·m-1. Here a bulk temperature of Tbulk = 74±2 °C was achieved for cPCL/mNP-OCL, which was almost 20 °C higher than the melting transition of the PCL-based polymer matrix. In contrast, the composite with plain mNPs could only reach a Tbulk of 48±2 °C, which is not sufficient for a complete melting of all PCL crystallites as required for actuation. The inductive heating capability of a multiphase copolymer nanocomposite network (designed as soft actuators) containing surface decorated mNPs as covalent netpoints was investigated. Such composite was synthesized from star-shaped OCL and OPDL precursors, as well as mNP-OCLs via reaction with HDI. The weight ratio of OPDL and OCL in the starting reaction mixture was 15/85 (wt\%/wt\%) and the amount of iron oxide in the nanocomposite was 4 wt\%. DSC experiments revealed two well separated melting and crystallization peaks confirming the required phase-segregated morphology in the nanocomposite NC-mNP-OCL. TEM images could illustrate a phase-segregated morphology of the polymer matrix on the microlevel with droplet shaped regions attributed to the OPDL domains dispersed in an OCL matrix. The TEM images could further demonstrate that the nanoparticulate netpoints in NC-mNP-OCL were almost homogeneously dispersed within the OCL domains. The tests of the inductive heating capability of the nanocomposites at a magnetic field strength of Hhigh = 11.2 kA·m-1 revealed a achievable plateau surface temperature of Tsurf = 57±1 °C for NC-mNP-OCL recorded by an infrared video camera. An effective heat generation constant (̅P) can be derived from a multi-scale model for the heat generation, which is proportional to the rate of heat generation per unit volume of the sample. NC-mNP-OCL with homogeneously dispersed mNP-OCLs exhibited a ̅P value of 1.04±0.01 K·s- 1 at Hhigh, while at Hreset = 30.0 kA·m-1 a Tsurf of 88±1 °C (where all OPDL related crystallite are molten) and a ̅P value of 1.93±0.02 K·s-1 was obtained indicating a high magnetic heating capability of the composite. The free-standing magnetically-controlled reversible shape-memory effect (mrSME) was explored with originally straight nanocomposite samples programmed by bending to an angle of 180°. By switching the magnetic field on and off the composite sample was allowed to repetitively heat to 60 °C and cool to the ambient temperature. A pronounced mrSME, characterized by changes in bending angle of Δϐrev = 20±3° could be obtained for a composite sample programmed by bending when a magnetic field strength of Hhigh = 11.2 kA·m-1 was applied in a multi-cyclic magnetic bending experiment with 600 heating-cooling cycles it could be shown that the actuation performance did not change with increasing number of test cycles, demonstrating the accuracy and reproducibility of this soft actuator. The degree of actuation as well as the kinetics of the shape changes during heating could be tuned by variation of the magnetic filed strength between Hlow and Hhigh or the magnetic field exposure time. When Hreset = 30.0 kA·m-1 was applied the programmed geometry was erased and the composite sample returned to it´s originally straight shape. The reprogrammability of the nanocomposite actuators was demonstrated by one and the same test specimen first exhibiting reversible angle changes when programmed by bending, secondly reprogrammed to a concertina, which expands upon inductive heating and contracts during cooling and finally reprogrammed to a clip like shape, which closes during cooling and opens when Hhigh was applied. In a next step the applicability of the presented remote controllable shape-memory polymer actuators was demonstrated by repetitive opening and closing of a multiring device prepared from NC-mNP-OCL, which repetitively opens and closes when a alternating magnetic field (Hhigh = 11.2 kA·m-1) was switched on and off. For investigation of the micro- and nanostructural changes related to the actuation of the developed nanocomposite, AFM and WAXS experiments were conducted with programmed nanocomposite samples under cyclic heating and cooling between 25 °C and 60 °C. In AFM experiments the change in the distance (D) between representative droplet-like structures related to the OPDL geometry determining domains was used to calculate the reversible change in D. Here Drev = 3.5±1\% was found for NC-mNP-OCL which was in good agreement with the results of the magneto-mechanical actuation experiments. Finally, the analysis of azimuthal (radial) WAXS scattering profiles could support the oriented crystallization of the OCL actuation domains at 25 °C. In conclusion, the results of this work successfully demonstrated that shape-memory polymer nanocomposites, containing mNPs as magneto-sensitive multifunctional netpoints in a covalently crosslinked multiphase polymer matrix, exhibit magnetically (remotely) controlled actuations upon repetitive exposure to an alternating magnetic field. Furthermore, the (shape) memory of such a nanocomposite can be erased by exposing it to temperatures above the melting temperature of the geometry forming domains, which allows a reprogramming of the actuator. These findings would be relevant for designing novel reprogrammable remotely controllable soft polymeric actuators.},
  language  = {en}
}
@phdthesis{Liu2021,
  author    = {Liu, Yue},
  title     = {Polymeric objects switchable between two shapes},
  school      = {Universit{\"a}t Potsdam},
  pages     = {xv, 73},
  year      = {2021},
  abstract  = {As the ongoing trend of developing smart materials that can reversibly switch geometry stimulated by environmental control addressed increasing attention in many research fields, especially for biomedical or soft robotic applications. Shape-memory polymers (SMPs), which can change shape, stiffness, size, and structure when exposed to an external stimulus, are intensively explored as encouraging material candidates for achieving multifunctionality, and for miniaturizing into micro-components to expand the applications. Besides, the geometrical design has gained growing attention for creating engineering applications, such as bi-stable mechanisms, and has the potential to be explored by implementing SMP for new functions. In this context, this thesis aimed to develop smart micro-/nano-objects based on SMP and explore new functions by geometrical design using SMP. Here, two types of stimuli-responsive objects capable of one-way temperature-memory effect (TME) or free-standing reversible actuation e.g., micro/nanofibers (i) and microcuboids (ii) at different aspects were explored. At first, it was hypothesized that the advanced atomic force microscopy (AFM) platform can be established to study individual polymeric micro-/nanofibers (i) in terms of incorporation and characterization of a reversible shape-memory actuation capability. Crystallizable material was chosen for preparing the fibers and the molecular alignment within the fibers among different diameters will influence the crystallization-induced elongation during cooling that determined the reversible effect. For the second type, microcuboids (ii), it was hypothesized that a programming and quantification approach can be developed to enable the realization and characterization of a one-way micro-TME and micro-shape-memory polymer actuation (SMPA) in microcuboids. The responsive temperature of one-way shape transformation can be tuned by programming temperature (Tp) and the separation temperature (Tsep) for post-programming can influence the actuation. Finally, a geometrical design with bi-stability was combined with SME to create new functions of shape actuation. It was hypothesized that the predicted bi-stable or mono-stable structures can be achieved with the aid of digital fabrication methods. Using shape-memory effect (SME), the alteration of bi-stable and mono-stable can initiate shape transformation with a larger magnitude and higher energy output. In the first part, the method to quantify the reversible SMPA of a single micro/nano crystallizable fiber with geometry change during the actuation was explored. Electrospinning was used to prepare poly (ε-caprolactone) (PCL) micro/nanofiber with different diameters, which were fixed by UV glue and crosslinked on the structured silicon wafer. Using AFM, the programming, as well as the observation of recovery and reversible displacement of the fiber, were performed by vertical three-point bending at the free suspended part. A plateau tip was chosen to achieve stable contact and longer working distance for performing larger deformation, enabling intensified reversible SMPA of single fibers. In this way, programming strains of 39 ± 1\% or 46 ± 1\% were realized for fiber with a diameter of 1 ± 0.2 µm and 300 ± 50 nm, which were bent at 80 °C and fixed at 10 °C. Values for the reversible elongation of εrev = 3.4 ± 0.1\% and 10.5 ± 0.1\% were obtained for a single micro and nanofiber respectively between 10 and 60 °C. The higher actuation effect observed for nanofiber demonstrated that the highly compact and oriented crystallites in nanofibers, which determined the pronounced εrev compared to the thick microfibers. Besides, a stable reversible actuation of a nanofiber can be tracked by AFM tip up to 10 cycles, indicating a sustainable application can be achieved on the fiber actuators. The findings obtained for cPCL micro-/nano-fibers will help design and evaluate the next generation polymeric microactuators or micromanipulators. The second part of the thesis studies the shape-memory effect (SME) of a single individual SMP micro-object by controlling deformation temperatures during programming and actuation temperatures during reversible change. In this work, microcuboids of crosslinked poly[ethylene-co-(vinyl acetate)] (cPEVA) elastomers with 18 wt\% vinyl acetate (VA) contents were successfully prepared by template-based replication from polydimethylsiloxane (PDMS) mold. The micro-TME and micro-SMPA were observed and studied based on micro-geometry change using optical microscopy (OM) and AFM. Different switching temperatures of shape recovery were achieved from 55 °C to 86 °C by tuning Tp from 55 °C to 100 °C, indicating a successful implementation of micro-TME on individual microcuboid. For micro-SMPA functionalization, microcuboids were deformed by compression at 100 °C and the change in single particle height was monitored during cyclic heating and cooling between various Tseps from 60 °C to 85 °C and 20 °C. The micro-SMPA on a single microcuboid was achieved with a reversible strain in the range of 2 to 7\%, whereby higher compression ratio CR and Tsep induced prominent reversible strain. The results achieved in this work demonstrated the successful functionalization of microcuboids with different SMEs by controlling temperatures during programming and actuation processes. Based on these achievements, such micro-objects can be further designed as on demand switchable microactuators or release systems with adjustable working temperatures. In the last part of the work, a new function of shape-memory polymeric bi-stable 3D structured film was designed and fabricated. The SME and geometrical design of compliant mechanics were merged to enable switching between bi-stable and mono-stable states, which generate snap movement that mimics the Venus flytrap. A truncated tetrahedron structure with a slope angle as a tunable parameter to alter the bi-stability was chosen for the study to combine with SME. It was anticipated that the structured film designed with a slope angle of 30° exhibited mono-stable behavior, and such a structure with a slope angle of 45° exhibited bi-stable behavior. Then the structured SMP film of designed mono-stable shape was successfully fabricated using soft lithography based on 3D printed master molds supported from digital manufacturing. The structured mold was also used in programming the SMP film into the structure with a higher slope angle to attain bi-stability. Finally, the switching between bi-stable and mono-stable states was successfully realized using SME, which introduces snapping movement triggered by heat. The implementation of compliant mechanisms by the SME increased the magnitude of thermally induced reconfiguration without additional external force. To sum up, the results of the thesis support the development of smart objects capable of one-way micro-TME, free-standing reversible actuation, or bi-stability mediated shape-memory reconfiguration. Electrospinning and template-based method were used for fabrication with good control of geometry and low size dispersity. Microscopy methods especially the AFM platform with decent sensitivity was developed for implementation as well as characterization of SME on individual micro-/nanoobjects. Implementation of bi-stability improves the shape transformation amplitude of thermally triggered SMP. These findings can give novel insights for designing polymer-based actuators or soft robotics.},
  language  = {en}
}