@article{ThiedeCabezaMishurovaetal.2018, author = {Thiede, Tobias and Cabeza, Sandra and Mishurova, Tatiana and Nadammal, Naresh and Kromm, Arne and Bode, Johannes and Haberland, Christoph and Bruno, Giovanni}, title = {Residual Stress in Selective Laser Melted Inconel 718}, series = {Materials performance and characterization}, volume = {7}, journal = {Materials performance and characterization}, number = {4}, publisher = {American Society for Testing and Materials}, address = {West Conshohocken}, issn = {2379-1365}, doi = {10.1520/MPC20170119}, pages = {717 -- 735}, year = {2018}, abstract = {The residual stress distribution in IN718 elongated prisms produced by selective laser melting was studied by means of neutron (bulk) and laboratory X-ray (surface) diffraction. Two deposition hatch lengths were considered. A horizontal plane near the top surface (perpendicular to the building direction) and a vertical plane near the lateral surface (parallel to the building direction) were investigated. Samples both in as-built (AB) condition and removed from the base plate (RE) were characterized. While surface stress fields seem constant for the AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements. Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e., with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the base plate.}, language = {en} } @article{StegemannCabezaPelkneretal.2018, author = {Stegemann, Robert and Cabeza, Sandra and Pelkner, Matthias and Lyamkin, Viktor and Pittner, Andreas and Werner, Daniel and Wimpory, Robert and Boin, Mirko and Kreutzbruck, Marc and Bruno, Giovanni}, title = {Influence of the microstructure on magnetic stray fields of low-carbon steel welds}, series = {Journal of Nondestructive Evaluation}, volume = {37}, journal = {Journal of Nondestructive Evaluation}, number = {3}, publisher = {Springer}, address = {New York}, issn = {0195-9298}, doi = {10.1007/s10921-018-0522-0}, pages = {18}, year = {2018}, abstract = {This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction. Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields.}, language = {en} } @article{SevostianovBruno2018, author = {Sevostianov, Igor and Bruno, Giovanni}, title = {Maxwell scheme for internal stresses in multiphase composites}, series = {Mechanics of Materials}, volume = {129}, journal = {Mechanics of Materials}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0167-6636}, doi = {10.1016/j.mechmat.2018.12.005}, pages = {320 -- 331}, year = {2018}, abstract = {The paper focuses on the reformulation of classic Maxwell's (1873) homogenization method for calculation of the residual stresses in matrix composites. For this goal, we equate the far fields produced by a set of inhomogeneities subjected to known eigenstrains and by a fictitious domain with unknown eigenstrain. The effect of interaction between the inhomogeneities is reduced to the calculation of the additional field acting on an inhomogeneity due to the eigenstrains in its neighbors. An explicit formula for residual stresses is derived for the general case of a multiphase composite. The method is illustrated by several examples. The results are compared with available experimental data as well as with predictions provided by the non-interaction approximation (Eshelby solution). It is shown that accounting for interaction can explain many experimentally observed phenomena and is required for adequate quantitative analytical modeling of the residual stresses in matrix composites.}, language = {en} } @article{NellesenLaquaiMuelleretal.2018, author = {Nellesen, Jens and Laquai, R. and M{\"u}ller, B. R. and Kupsch, Andreas and Hentschel, M. P. and Anar, N. B. and Soppa, E. and Tillmann, W. and Bruno, Giovanni}, title = {In situ analysis of damage evolution in an Al/ Al2O3 MMC under tensile load by synchrotron X-ray refraction imaging}, series = {Journal of materials science}, volume = {53}, journal = {Journal of materials science}, number = {8}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-017-1957-x}, pages = {6021 -- 6032}, year = {2018}, abstract = {The in situ analysis of the damage evolution in a metal matrix composite (MMC) using synchrotron X-ray refraction radiography (SXRR) is presented. The investigated material is an Al alloy (6061)/10 vol MMC after T6 heat treatment. In an interrupted tensile test the gauge section of dog bone-shaped specimens is imaged in different states of tensile loading. On the basis of the SXRR images, the relative change of the specific surface (proportional to the amount of damage) in the course of tensile loading was analyzed. It could be shown that the damage can be detected by SXRR already at a stage of tensile loading, in which no observation of damage is possible with radiographic absorption-based imaging methods. Moreover, the quantitative analysis of the SXRR images reveals that the amount of damage increases homogeneously by an average of 25\% with respect to the initial state. To corroborate the experimental findings, the damage distribution was imaged in 3D after the final tensile loading by synchrotron X-ray refraction computed tomography (SXRCT) and absorption-based synchrotron X-ray computed tomography (SXCT). It could be evidenced that defects and damages cause pronounced indications in the SXRCT images.}, language = {en} } @misc{MuellerKupschLaquaietal.2018, author = {M{\"u}ller, Bernd Randolf and Kupsch, Andreas and Laquai, Rene and Nellesen, Jens and Tillmann, Wolfgang and Kasperovich, Galina and Bruno, Giovanni}, title = {Microstructure Characterisation of Advanced Materials via 2D and 3D X-Ray Refraction Techniques}, series = {Materials Science Forum}, volume = {941}, journal = {Materials Science Forum}, publisher = {Trans Tech Publications Ltd}, address = {Zurich}, isbn = {978-3-0357-1208-7}, issn = {0255-5476}, doi = {10.4028/www.scientific.net/MSF.941.2401}, pages = {2401 -- 2406}, year = {2018}, abstract = {3D imaging techniques have an enormous potential to understand the microstructure, its evolution, and its link to mechanical, thermal, and transport properties. In this conference paper we report the use of a powerful, yet not so wide-spread, set of X-ray techniques based on refraction effects. X-ray refraction allows determining internal specific surface (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with a nanometric detectability. We demonstrate showcases of ceramics and composite materials, where microstructural parameters could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. We present in situ analysis of the damage evolution in an Al/Al2O3 metal matrix composite during tensile load and the identification of void formation (different kinds of defects, particularly unsintered powder hidden in pores, and small inhomogeneity's like cracks) in Ti64 parts produced by selective laser melting using synchrotron X-ray refraction radiography and tomography.}, language = {en} } @article{MishurovaCabezaThiedeetal.2018, author = {Mishurova, Tatiana and Cabeza, Sandra and Thiede, Tobias and Nadammal, Naresh and Kromm, Arne and Klaus, Manuela and Genzel, Christoph and Haberland, Christoph and Bruno, Giovanni}, title = {The Influence of the Support Structure on Residual Stress and Distortion in SLM Inconel 718 Parts}, series = {Metallurgical and Materials Transactions A}, volume = {49A}, journal = {Metallurgical and Materials Transactions A}, number = {7}, publisher = {Springer}, address = {New York}, issn = {1073-5623}, doi = {10.1007/s11661-018-4653-9}, pages = {3038 -- 3046}, year = {2018}, abstract = {The effect of support structure and of removal from the base plate on the residual stress state in selective laser melted IN718 parts was studied by means of synchrotron X-ray diffraction. The residual stresses in subsurface region of two elongated prisms in as-built condition and after removal from the base plate were determined. One sample was directly built on a base plate and another one on a support structure. Also, the distortion on the top surface due to stress release was measured by contact profilometry. High tensile residual stress values were found, with pronounced stress gradient along the hatching direction. In the sample on support, stress redistribution took place after removal from the base plate, as opposed to simple stress relaxation for the sample without support. The sample on support structure showed larger distortion compared to sample without support. We conclude that the use of a support decreases stress values but stress-relieving heat treatments are still needed.}, language = {en} } @article{MishurovaArtztHaubrichetal.2018, author = {Mishurova, Tatiana and Artzt, Katia and Haubrich, Jan and Requena, Guillermo and Bruno, Giovanni}, title = {New aspects about the search for the most relevant parameters optimizing SLM materials}, series = {Additive manufacturing}, volume = {25}, journal = {Additive manufacturing}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2214-8604}, doi = {10.1016/j.addma.2018.11.023}, pages = {325 -- 334}, year = {2018}, abstract = {While the volumetric energy density is commonly used to qualify a process parameter set, and to quantify its influence on the microstructure and performance of additively manufactured (AM) materials and components, it has been already shown that this description is by no means exhaustive. In this work, new aspects of the optimization of the selective laser melting process are investigated for AM Ti-6Al-4V. We focus on the amount of near-surface residual stress (RS), often blamed for the failure of components, and on the porosity characteristics (amount and spatial distribution). First, using synchrotron x-ray diffraction we show that higher RS in the subsurface region is generated if a lower energy density is used. Second, we show that laser de-focusing and sample positioning inside the build chamber also play an eminent role, and we quantify this influence. In parallel, using X-ray Computed Tomography, we observe that porosity is mainly concentrated in the contour region, except in the case where the laser speed is small. The low values of porosity (less than 1\%) do not influence RS.}, language = {en} } @article{FernandezSerranoBrunoGonzalezDoncel2018, author = {Fernandez Serrano, Ricardo and Bruno, Giovanni and Gonzalez-Doncel, Gaspar}, title = {Fractal nature of aluminum alloys substructures under creep and its implications}, series = {Journal of applied physics}, volume = {123}, journal = {Journal of applied physics}, number = {14}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/1.5012035}, pages = {8}, year = {2018}, abstract = {The present work offers an explanation for the variation of the power-law stress exponent, n, with the stress sigma normalized to the shear modulus G in aluminum alloys. The approach is based on the assumption that the dislocation structure generated with deformation has a fractal nature. It fully explains the evolution of n with sigma/G even beyond the so-called power law breakdown region. Creep data from commercially pure Al99.8\%, Al-3.85\%Mg, and ingot AA6061 alloy tested at different temperatures and stresses are used to validate the proposed ideas. Finally, it is also shown that the fractal description of the dislocation structure agrees well with current knowledge. Published by AIP Publishing.}, language = {en} } @article{FernandezCabezaMishurovaetal.2018, author = {Fernandez, R. and Cabeza, Sandra and Mishurova, Tatiana and Fernandez-Castrillo, P. and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Residual stress and yield strength evolution with annealing treatments in an age-hardenable aluminum alloy matrix composite}, series = {Materials Science and Engineering: A}, volume = {731}, journal = {Materials Science and Engineering: A}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.06.031}, pages = {344 -- 350}, year = {2018}, abstract = {We investigated the possibility of minimizing tensile matrix residual stresses in age hardenable aluminum alloy metal matrix composites without detrimentally affect their mechanical properties (such as yield strength). Specifically, we performed thermal treatments at different temperatures and times in an age-hardenable aluminum matrix composite 2014Al-15vol\%Al2O3. Using X-ray synchrotron radiation diffraction and mechanical tests, we show that below a certain treatment temperature (250 degrees C) it is possible to identify an appropriate thermal treatment capable of relaxing residual stress in this composite while even increasing its yield strength, with respect to the as processed conditions.}, language = {en} } @article{EvsevleevMishurovaCabezaetal.2018, author = {Evsevleev, Sergei and Mishurova, Tatiana and Cabeza, Sandra and Koos, R. and Sevostianov, Igor and Garc{\´e}s, Gonzales and Requena, Guillermo and Fernandez, R. and Bruno, Giovanni}, title = {The role of intermetallics in stress partitioning and damage evolution of AlSil2CuMgNi alloy}, series = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, volume = {736}, journal = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.08.070}, pages = {453 -- 464}, year = {2018}, abstract = {Load partitioning between phases in a cast AlSi12CuMgNi alloy was investigated by in-situ compression test during neutron diffraction experiments. Computed tomography (CT) was used to determine volume fractions of eutectic Si and intermetallic (IM) phases, and to assess internal damage after ex-situ compression tests. The CT reconstructed volumes showed the interconnectivity of IM phases, which build a 3D network together with eutectic Si. Large stresses were found in IMs, revealing their significant role as a reinforcement for the alloy. An existing micromechanical model based on Maxwell scheme was extended to the present case, assuming the alloy as a three-phase composite (Al matrix, eutectic Si, IM phases). The model agrees well with the experimental data. Moreover, it allows predicting the principal stresses in each phase, while experiments can only determine stress differences between the axial and radial sample directions. Finally, we showed that the addition of alloying elements not only allowed developing a 3D interconnected network, but also improved the strength of the Al matrix, and the ability of the alloy constituents to bear mechanical load.}, language = {en} } @article{CabezaMuellerPereyraetal.2018, author = {Cabeza, Sandra and M{\"u}ller, Bernd R. and Pereyra, Ricio and Fernandez, Ricardo and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Evidence of damage evolution during creep of Al-Mg alloy using synchrotron X-ray refraction}, series = {Journal of applied crystallography}, volume = {51}, journal = {Journal of applied crystallography}, publisher = {International Union of Crystallography}, address = {Chester}, issn = {1600-5767}, doi = {10.1107/S1600576718001449}, pages = {420 -- 427}, year = {2018}, abstract = {In order to provide further evidence of damage mechanisms predicted by the recent solid-state transformation creep (SSTC) model, direct observation of damage accumulation during creep of Al-3.85Mg was made using synchrotron X-ray refraction. X-ray refraction techniques detect the internal specific surface (i.e. surface per unit volume) on a length scale comparable to the specimen size, but with microscopic sensitivity. A significant rise in the internal specific surface with increasing creep time was observed, providing evidence for the creation of a fine grain substructure, as predicted by the SSTC model. This substructure was also observed by scanning electron microscopy.}, language = {en} } @article{BuljakBruno2018, author = {Buljak, Vladimir and Bruno, Giovanni}, title = {Numerical modeling of thermally induced microcracking in porous ceramics}, series = {Journal of the European Ceramic Society}, volume = {38}, journal = {Journal of the European Ceramic Society}, number = {11}, publisher = {Elsevier}, address = {Oxford}, issn = {0955-2219}, doi = {10.1016/j.jeurceramsoc.2018.03.041}, pages = {4099 -- 4108}, year = {2018}, abstract = {A numerical framework is developed to study the hysteresis of elastic properties of porous ceramics as a function of temperature. The developed numerical model is capable of employing experimentally measured crystallographic orientation distribution and coefficient of thermal expansion values. For realistic modeling of the microstructure, Voronoi polygons are used to generate polycrystalline grains. Some grains are considered as voids, to simulate the material porosity. To model intercrystalline cracking, cohesive elements are inserted along grain boundaries. Crack healing (recovery of the initial properties) upon closure is taken into account with special cohesive elements implemented in the commercial code ABAQUS. The numerical model can be used to estimate fracture properties governing the cohesive behavior through inverse analysis procedure. The model is applied to a porous cordierite ceramic. The obtained fracture properties are further used to successfully simulate general non-linear macroscopic stress-strain curves of cordierite, thereby validating the model.}, language = {en} } @article{BrunoKachanovSevostianovetal.2018, author = {Bruno, Giovanni and Kachanov, Mark and Sevostianov, Igor and Shyam, Amit}, title = {Micromechanical modeling of non-linear stress-strain behavior of polycrystalline microcracked materials under tension}, series = {Acta materialia}, volume = {164}, journal = {Acta materialia}, publisher = {Elsevier}, address = {Oxford}, issn = {1359-6454}, doi = {10.1016/j.actamat.2018.10.024}, pages = {50 -- 59}, year = {2018}, abstract = {The stress-strain behavior of microcracked polycrystalline materials (such as ceramics or rocks) under conditions of tensile, displacement-controlled, loading is discussed. Micromechanical explanation and modeling of the basic features, such as non-linearity and hysteresis in stress-strain curves, is developed, with stable microcrack propagation and "roughness" of intergranular cracks playing critical roles. Experiments involving complex loading histories were done on large- and medium grain size beta-eucryptite ceramic. The model is shown to reproduce the basic features of the observed stress-strain curves. (C) 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.}, language = {en} }