@article{TitovSharmaLomadzeetal.2021, author = {Titov, Evgenii and Sharma, Anjali and Lomadze, Nino and Saalfrank, Peter and Santer, Svetlana and Bekir, Marek}, title = {Photoisomerization of an azobenzene-containing surfactant within a micelle}, series = {ChemPhotoChem}, volume = {5}, journal = {ChemPhotoChem}, number = {10}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {2367-0932}, doi = {10.1002/cptc.202100103}, pages = {926 -- 932}, year = {2021}, abstract = {Photosensitive azobenzene-containing surfactants have attracted great attention in past years because they offer a means to control soft-matter transformations with light. At concentrations higher than the critical micelle concentration (CMC), the surfactant molecules aggregate and form micelles, which leads to a slowdown of the photoinduced trans -> cis azobenzene isomerization. Here, we combine nonadiabatic dynamics simulations for the surfactant molecules embedded in the micelles with absorption spectroscopy measurements of micellar solutions to uncover the reasons responsible for the reaction slowdown. Our simulations reveal a decrease of isomerization quantum yields for molecules inside the micelles. We also observe a reduction of extinction coefficients upon micellization. These findings explain the deceleration of the trans -> cis switching in micelles of the azobenzene-containing surfactants.}, language = {en} } @article{GarnierLaschewsky2006, author = {Garnier, Sebastien and Laschewsky, Andre}, title = {Non-ionic amphiphilic block copolymers by RAFT-polymerization and their self-organization}, series = {Colloid and polymer science : official journal of the Kolloid-Gesellschaft}, volume = {284}, journal = {Colloid and polymer science : official journal of the Kolloid-Gesellschaft}, publisher = {Springer}, address = {Berlin}, issn = {0303-402X}, doi = {10.1007/s00396-006-1484-9}, pages = {1243 -- 1254}, year = {2006}, abstract = {Water-soluble, amphiphilic diblock copolymers were synthesized by reversible addition fragmentation chain transfer polymerization. They consist of poly(butyl acrylate) as hydrophobic block with a low glass transition temperature and three different nonionic water-soluble blocks, namely, the classical hydrophilic block poly(dimethylacrylamide), the strongly hydrophilic poly(acryloyloxyethyl methylsulfoxide), and the thermally sensitive poly(N-acryloylpyrrolidine). Aqueous micellar solutions of the block copolymers were prepared and characterized by static and dynamic light scattering analysis (DLS and SLS). No critical micelle concentration could be detected. The micellization was thermodynamically favored, although kinetically slow, exhibiting a marked dependence on the preparation conditions. The polymers formed micelles with a hydrodynamic diameter from 20 to 100 nm, which were stable upon dilution. The micellar size was correlated with the composition of the block copolymers and their overall molar mass. The micelles formed with the two most hydrophilic blocks were particularly stable upon temperature cycles, whereas the thermally sensitive poly(N-acryloylpyrrolidine) block showed a temperature-induced precipitation. According to combined SLS and DLS analysis, the micelles exhibited an elongated shape such as rods or worms. It should be noted that the block copolymers with the most hydrophilic poly(sulfoxide) block formed inverse micelles in certain organic solvents.}, language = {en} } @phdthesis{tenBrummelhuis2011, author = {ten Brummelhuis, Niels}, title = {Self-assembly of cross-linked polymer micelles into complex higher-order aggregates}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-52320}, school = {Universit{\"a}t Potsdam}, year = {2011}, abstract = {The creation of complex polymer structures has been one of the major research topics over the last couple of decades. This work deals with the synthesis of (block co-)polymers, the creation of complex and stimuli-responsive aggregates by self-assembly, and the cross-linking of these structures. Also the higher-order self-assembly of the aggregates is investigated. The formation of poly-2-oxazoline based micelles in aqueous solution and their simultaneous functionalization and cross-linking using thiol-yne chemistry is e.g. presented. By introducing pH responsive thiols in the core of the micelles the influence of charged groups in the core of micelles on the entire structure can be studied. The charging of these groups leads to a swelling of the core and a decrease in the local concentration of the corona forming block (poly(2-ethyl-2-oxazoline)). This decrease in concentration yields a shift in the cloud point temperature to higher temperatures for this Type I thermoresponsive polymer. When the swelling of the core is prohibited, e.g. by the introduction of sufficient amounts of salt, this behavior disappears. Similar structures can be prepared using complex coacervate core micelles (C3Ms) built through the interaction of weakly acidic and basic polymer blocks. The advantage of these structures is that two different stabilizing blocks can be incorporated, which allows for more diverse and complex structures and behavior of the micelles. Using block copolymers with either a polyanionic or a polycationic block C3Ms could be created with a corona which contains two different soluble nonionic polymers, which either have a mixed corona or a Janus type corona, depending on the polymers that were chosen. Using NHS and EDC the micelles could easily be cross-linked by the formation of amide bonds in the core of the micelles. The higher-order self-assembly behavior of these core cross-linked complex coacervate core micelles (C5Ms) was studied. Due to the cross-linking the micelles are stabilized towards changes in pH and ionic strength, but polymer chains are also no longer able to rearrange. For C5Ms with a mixed corona likely network structures were formed upon the collapse of the thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm), whereas for Janus type C5Ms well defined spherical aggregates of micelles could be obtained, depending on the pH of the solution. Furthermore it could be shown that Janus micelles can adsorb onto inorganic nanoparticles such as colloidal silica (through a selective interaction between PEO and the silica surface) or gold nanoparticles (by the binding of thiol end-groups). Asymmetric aggregates were also formed using the streptavidin-biotin binding motive. This is achieved by using three out of the four binding sites of streptavidin for the binding of one three-arm star polymer, end-functionalized with biotin groups. A homopolymer with one biotin end-group can be used to occupy the last position. This binding of two different polymers makes it possible to create asymmetric complexes. This phase separation is theoretically independent of the kind of polymer since the structure of the protein is the driving force, not the intrinsic phase separation between polymers. Besides Janus structures also specific cross-linking can be achieved by using other mixing ratios.}, language = {en} } @phdthesis{Nazaran2008, author = {Nazaran, Pantea}, title = {Nucleation in emulsion polymerization : steps towards a non-micellar nucleation theory}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-17521}, school = {Universit{\"a}t Potsdam}, year = {2008}, abstract = {For more than 70 years, understanding of the mechanism of particle nucleation in emulsion polymerization has been one of the most challenging issues in heterophase polymerization research. Within this work a comprehensive experimental study of particle nucleation in emulsion polymerization of styrene at 70 °C and variety of conditions has been performed. To follow the onset of nucleation, on-line conductivity measurements were applied. This technique is highly sensitive to the mobility of conducting species and hence, it can be employed to follow aggregation processes leading to particle formation. On the other hand, by recording the optical transmission (turbidity) of the reaction mixture particle growth was followed. Complementary to the on-line investigations, off-line characterizations of the particle morphology and the molecular weight have been performed. The aim was to achieve a better insight in the processes taking place after starting the reaction via particle nucleation until formation of colloidally stable latex particles. With this experimental protocol the initial period of styrene emulsion polymerization in the absence as well as in the presence of various surfactants (concentrations above and below the critical micellization concentration) and also in the presence of seed particles has been investigated. Ionic and non-ionic initiators (hydrophilic and hydrophobic types) have been applied to start the polymerizations. Following the above algorithm, experimental evidence has been obtained showing the possibility of performing surfactant-free emulsion polymerization of styrene with oil-soluble initiators. The duration of the pre-nucleation period (that is the time between starting the polymerization and nucleation) can be precisely adjusted with the initiator hydrophobicity, the equilibration time of styrene in water, and the surfactant concentration. Spontaneous emulsification of monomer in water, as soon as both phases are brought into contact, is a key factor to explain the experimental results. The equilibration time of monomer in water as well as the type and concentration of other materials in water (surfactants, seed particles, etc.) control the formation rate and the size of the emulsified droplets and thus, have a strong influence on the particle nucleation and the particle morphology. One of the main tasks was to investigate the effect of surfactant molecules and especially micelles on the nucleation mechanism. Experimental results revealed that in the presence of emulsifier micelles the conductivity pattern does not change essentially. This means that the presence of emulsifiers does not change the mechanism of particle formation qualitatively. However, surfactants assist in the nucleation process as they lower the activation free energy of particle formation. Contrary, seed particles influence particle nucleation, substantially. In the presence of seed particles above a critical volume fraction the formation of new particles can be suppressed. However, micelles and seed particles as absorbers exhibit a common behavior under conditions where monomer equilibration is not allowed. Results prove that the nucleation mechanism comprises the initiation of water soluble oligomers in the aqueous phase followed by their aggregation. The process is heterogeneous in nature due to the presence of monomer droplets.}, language = {en} } @phdthesis{Kubowicz2005, author = {Kubowicz, Stephan}, title = {Design and characterization of multicompartment micelles in aqueous solution}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-5752}, school = {Universit{\"a}t Potsdam}, year = {2005}, abstract = {Self-assembly of polymeric building blocks is a powerful tool for the design of novel materials and structures that combine different properties and may respond to external stimuli. In the past decades, most studies were focused on the self-assembly of amphiphilic diblock copolymers in solution. The dissolution of these block copolymers in a solvent selective for one block results mostly in the formation of micelles. The micellar structure of diblock copolymers is inherently limited to a homogeneous core surrounded by a corona, which keeps the micelle in solution. Thus, for drug-delivery applications, such structures only offer a single domain (the hydrophobic inner core) for drug entrapment. Whereas multicompartment micelles composed of a water-soluble shell and a segregated hydrophobic core are novel, interesting morphologies for applications in a variety of fields including medicine, pharmacy and biotechnology. The separated incompatible compartments of the hydrophobic core could enable the selective entrapment and release of various hydrophobic drugs while the hydrophilic shell would permit the stabilization of these nanostructures in physiological media. However, so far, the preparation and control of stable multicompartment micellar systems are in the first stages and the number of morphological studies concerning such micelles is rather low. Thus considerably little is known about their exact inner structures. In the present study, we concentrate on four different approaches for the preparation of multicompartment micelles by self-assembly in aqueous media. A similarity of all approaches was that hydrocarbon and fluorocarbon blocks were selected for all employed copolymers since such segments tend to be strongly incompatible, and thus favor the segregation into distinct domains. Our studies have shown that the self-assembly of the utilized copolymers in aqueous solution leads in three cases to the formation of multicompartment micelles. As expected the shape and size of the micelles depend on the molecular architecture and to some extent also on the way of preparation. These novel structured colloids may serve as models as well as mimics for biological structures such as globular proteins, and may open interesting opportunities for nanotechnology applications.}, subject = {Amphiphile Verbindungen}, language = {en} } @phdthesis{Krasia2003, author = {Krasia, Theodora}, title = {Synthese und kolloidale Eigenschaften neuartiger Blockcopolymere mit beta-Dicarbonyl Einheiten = Synthesis and colloidal properties of a novel type of block copolymers bearing beta-dicarbonyl residues}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-0000787}, school = {Universit{\"a}t Potsdam}, year = {2003}, abstract = {The present work is dealing with the first synthesis and characterisation of amphiphilic diblock copolymers bearing b-dicarbonyl (acetoacetoxy) chelating residues. Polymers were obtained by Group Transfer Polymerisation (GTP)/acetoacetylation and controlled radical polymerisation techniques (RAFT).Different micellar morphologies of poly(n-butyl methacrylate)-block-poly[2-(acetoacetoxy)ethyl methacrylate] (pBuMA-b-pAEMA) were observed in cyclohexane as a selective solvent. Depending on the block length ratio, either spherical, elliptical, or cylindrical micelles were formed. The density of the polymer chains at the core/corona interface is considerably higher as compared to any other strongly segregating system reported in the literature. It is demonstrated that there are H-bond interactions existing between acetoacetoxy groups, which increase the incompatibility between block segments. In addition, such interactions lead to the formation of secondary structures (such as b-sheets or globular structures) and larger superstructures in the micrometer length scale.Block copolymers were also used to solubilise metal ion salts of different geometries and oxidation states in organic media, in which are otherwise insoluble. Sterically stabilised colloidal hybrid materials are formed, i.e. monodisperse micelles having the metal ion salt incorporated in their core upon complexation with the ligating pAEMA block, whereas pBuMA forms the solvating corona responsible for stabilisation in solution. Systematic studies show that the aggregation behaviour is dependent on different factors, such as the tautomeric form of the beta-dicarbonyl ligand (keto/enol) as well as the nature and amount of added metal ion salt.}, language = {en} }