@phdthesis{Haase2011,
  author    = {Haase, Martin F.},
  title     = {Modification of nanoparticle surfaces for emulsion stabilization and encapsulation of active molecules for anti-corrosive coatings},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-55413},
  school      = {Universit{\"a}t Potsdam},
  year      = {2011},
  abstract  = {Within this work, three physicochemical methods for the hydrophobization of initially hydrophilic solid particles are investigated. The modified particles are then used for the stabilization of oil-in-water (o/w) emulsions. For all introduced methods electrostatic interactions between strongly or weakly charged groups in the system are es-sential. (i) Short chain alkylammonium bromides (C4 - C12) adsorb on oppositely charged solid particles. Macroscopic contact angle measurements of water droplets under air and hexane on flat silica surfaces in dependency of the surface charge density and alkylchain-length allow the calculation of the surface energy and give insights into the emulsification properties of solid particles modified with alkyltrimethylammonium bromides. The measure-ments show an increase of the contact angle with increasing surface charge density, due to the enhanced adsorp-tion of the oppositely charged alkylammonium bromides. Contact angles are higher for longer alkylchain lengths. The surface energy calculations show that in particular the surface-hexane or surface-air interfacial en-ergy is being lowered upon alkylammonium adsorption, while a significant increase of the surface-water interfa-cial energy occurs only at long alkyl chain lengths and high surface charge densities. (ii) The thickness and the charge density of an adsorbed weak polyelectrolyte layer (e.g. PMAA, PAH) influence the wettability of nanoparticles (e.g. alumina, silica, see Scheme 1(b)). Furthermore, the isoelectric point and the pH range of colloidal stability of particle-polyelectrolyte composites depend on the thickness of the weak polye-lectrolyte layer. Silica nanoparticles with adsorbed PAH and alumina nanoparticles with adsorbed PMAA be-come interfacially active and thus able to stabilize o/w emulsions when the degree of dissociation of the polye-lectrolyte layer is below 80 \%. The average droplet size after emulsification of dodecane in water depends on the thickness and the degree of dissociation of the adsorbed PE-layer. The visualization of the particle-stabilized o/w emulsions by cryogenic SEM shows that for colloidally stable alumina-PMAA composites the oil-water interface is covered with a closely packed monolayer of particles, while for the colloidally unstable case closely packed aggregated particles deposit on the interface. (iii) By emulsifying a mixture of the corrosion inhibitor 8-hydroxyquinoline (8-HQ) and styrene with silica nanoparticles a highly stable o/w emulsion can be obtained in a narrow pH window. The amphoteric character of 8-HQ enables a pH dependent electrostatic interaction with silica nanoparticles, which can render them interfa-cially active. Depending on the concentration and the degree of dissociation of 8-HQ the adsorption onto silica results from electrostatic or aromatic interactions between 8-HQ and the particle-surface. At intermediate amounts of adsorbed 8-HQ the oil wettability of the particles becomes sufficient for stabilizing o/w emulsions. Cryogenic SEM visualization shows that the particles arrange then in a closely packed shell consisting of partly of aggregated domains on the droplet interface. For further increasing amounts of adsorbed 8-HQ the oil wet-tability is reduced again and the particles ability to stabilize emulsions decreases. By the addition of hexadecane to the oil phase the size of the droplets can be reduced down to 200 nm by in-creasing the silica mass fraction. Subsequent polymerization produces corrosion inhibitor filled (20 wt-\%) poly-styrene-silica composite particles. The measurement of the release of 8-hydroxyquinoline shows a rapid increase of 8-hydroxyquinoline in a stirred aqueous solution indicating the release of the total content in less than 5 min-utes. The method is extended for the encapsulation of other organic corrosion inhibitors. The silica-polymer-inhibitor composite particles are then dispersed in a water based alkyd emulsion, and the dispersion is used to coat flat aluminium substrates. After drying and cross-linking the polmer-film Confocal Laser Scanning Micros-copy is employed revealing a homogeneous distribution of the particles in the film. Electrochemical Impedance Spectroscopy in aqueous electrolyte solutions shows that films with aggregated particle domains degrade with time and don't provide long-term corrosion protection of the substrate. However, films with highly dispersed particles have high barrier properties for corrosive species. The comparison of films containing silica-polystyrene composite particles with and without 8-hydroxyquinoline shows higher electrochemical impedances when the inhibitor is present in the film. By applying the Scanning Vibrating Electrode Technique the localized corrosion rate in the fractured area of scratched polymer films containing the silica-polymer-inhibitor composite particles is studied. Electrochemical corrosion cannot be suppressed but the rate is lowered when inhibitor filled composite particles are present in the film. By depositing six polyelectrolyte layers on particle stabilized emulsion droplets their surface morphology changes significantly as shown by SEM visualization. When the oil wettability of the outer polyelectrolyte layer increases, the polyelectrolyte coated droplets can act as emulsion stabilizers themselves by attaching onto bigger oil droplets in a closely packed arrangement. In the presence of 3 mM LaCl3 8-HQ hydrophobized silica particles aggregate strongly on the oil-water inter-face. The application of an ultrasonic field can remove two dimensional shell-compartments from the droplet surface, which are then found in the aqueous bulk phase. Their size ranges up to 1/4th of the spherical particle shell.},
  language  = {en}
}
@phdthesis{Lerm2012,
  author    = {Lerm, Stephanie},
  title     = {Mikroorganismen in geothermischen Aquiferen : Einfluss mikrobieller Prozesse auf den Anlagenbetrieb},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-63705},
  school      = {Universit{\"a}t Potsdam},
  year      = {2012},
  abstract  = {In Fluid-, Filter- und Sedimentproben von vier geothermischen Anlagen des Norddeutschen Beckens wurden mit molekulargenetischen Verfahren unterschiedliche mikrobielle Gemeinschaften nachgewiesen. Die mikrobielle Zusammensetzung in den Prozessw{\"a}ssern wurde dabei durch die Aquiferteufe, die Salinit{\"a}t, die Temperatur und den verf{\"u}gbaren Elektronendonatoren und -akzeptoren beeinflusst. Die in den anoxischen Prozessw{\"a}ssern identifizierten Organismen zeichneten sich durch einen chemoheterotrophen oder chemoautotrophen Stoffwechsel aus, wobei Nitrat, Sulfat, Eisen (III) oder Bikarbonat als terminale Elektronenakzeptoren fungierten. Mikroorganismen beeinflussten den Betrieb von zwei Anlagen negativ. So reduzierten im Prozesswasser des K{\"a}ltespeichers am Berliner Reichstag vorhandene Eisenoxidierer, nahe verwandt zu der Gattung Gallionella, die Injektivit{\"a}t der Bohrungen durch Eisenhydroxidausf{\"a}llungen in den Filterschlitzen. Biofilme, die von schwefeloxidierenden Bakterien der Gattung Thiothrix in den Filtern der obert{\"a}gigen Anlage gebildet wurden, f{\"u}hrten ebenfalls zu Betriebsst{\"o}rungen, indem sie die Injektion des Fluids in den Aquifer behinderten. Beim W{\"a}rmespeicher in Neubrandenburg waren Sulfatreduzierer vermutlich an der Bildung von Eisensulfidausf{\"a}llungen in den obert{\"a}gigen Filtern und im bohrlochnahen Bereich beteiligt und verst{\"a}rkten Korrosionsprozesse an der Pumpe im Bohrloch der kalten Aquiferseite. Organische S{\"a}uren in den Fluiden sowie mineralische Ausf{\"a}llungen in den Filtern der obert{\"a}gigen Anlagen waren Belege f{\"u}r die Aktivit{\"a}t der in den verschiedenen Anlagen vorhandenen Mikroorganismen. Es wurde zudem deutlich, dass Mikroorganismen auf Grund der hohen Durchflussraten in den Anlagen chemische Ver{\"a}nderungen in den Prozessw{\"a}ssern deutlich sensitiver anzeigen als chemische Analyseverfahren. So deuteten {\"A}nderungen in der Zusammensetzung der mikrobiellen Bioz{\"o}nosen und speziell die Identifikation von Indikatororganismen wie Eisen- und Schwefeloxidierern, fermentativen Bakterien und Sulfatreduzierern auf eine erh{\"o}hte Verf{\"u}gbarkeit von Elektronendonatoren oder akzeptoren in den Prozessw{\"a}ssern hin. Die Ursachen f{\"u}r die an den Geothermieanlagen auftretenden Betriebsst{\"o}rungen konnten dadurch erkannt werden.},
  language  = {de}
}
@phdthesis{Latnikova2012,
  author    = {Latnikova, Alexandra},
  title     = {Polymeric capsules for self-healing anticorrosion coatings},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-60432},
  school      = {Universit{\"a}t Potsdam},
  year      = {2012},
  abstract  = {The present work is devoted to establishing of a new generation of self-healing anti-corrosion coatings for protection of metals. The concept of self-healing anticorrosion coatings is based on the combination of the passive part, represented by the matrix of conventional coating, and the active part, represented by micron-sized capsules loaded with corrosion inhibitor. Polymers were chosen as the class of compounds most suitable for the capsule preparation. The morphology of capsules made of crosslinked polymers, however, was found to be dependent on the nature of the encapsulated liquid. Therefore, a systematic analysis of the morphology of capsules consisting of a crosslinked polymer and a solvent was performed. Three classes of polymers such as polyurethane, polyurea and polyamide were chosen. Capsules made of these polymers and eight solvents of different polarity were synthesized via interfacial polymerization. It was shown that the morphology of the resulting capsules is specific for every polymer-solvent pair. Formation of capsules with three general types of morphology, such as core-shell, compact and multicompartment, was demonstrated by means of Scanning Electron Microscopy. Compact morphology was assumed to be a result of the specific polymer-solvent interactions and be analogues to the process of swelling. In order to verify the hypothesis, pure polyurethane, polyurea and polyamide were synthesized; their swelling behavior in the solvents used as the encapsulated material was investigated. It was shown that the swelling behavior of the polymers in most cases correlates with the capsules morphology. Different morphologies (compact, core-shell and multicompartment) were therefore attributed to the specific polymer-solvent interactions and discussed in terms of "good" and "poor" solvent. Capsules with core-shell morphology are formed when the encapsulated liquid is a "poor" solvent for the chosen polymer while compact morphologies are formed when the solvent is "good". Multicompartment morphology is explained by the formation of infinite networks or gelation of crosslinked polymers. If gelation occurs after the phase separation in the system is achieved, core-shell morphology is present. If gelation of the polymer occurs far before crosslinking is accomplished, further condensation of the polymer due to the crosslinking may lead to the formation of porous or multicompartment morphologies. It was concluded that in general, the morphology of capsules consisting of certain polymer-solvent pairs can be predicted on the basis of polymer-solvent behavior. In some cases, the swelling behavior and morphology may not match. The reasons for that are discussed in detail in the thesis. The discussed approach is only capable of predicting capsule morphology for certain polymer-solvent pairs. In practice, the design of the capsules assumes the trial of a great number of polymer-solvent combinations; more complex systems consisting of three, four or even more components are often used. Evaluation of the swelling behavior of each component pair of such systems becomes unreasonable. Therefore, exploitation of the solubility parameter approach was found to be more useful. The latter allows consideration of the properties of each single component instead of the pair of components. In such a manner, the Hansen Solubility Parameter (HSP) approach was used for further analysis. Solubility spheres were constructed for polyurethane, polyurea and polyamide. For this a three-dimensional graph is plotted with dispersion, polar and hydrogen bonding components of solubility parameter, obtained from literature, as the orthogonal axes. The HSP of the solvents are used as the coordinates for the points on the HSP graph. Then a sphere with a certain radius is located on a graph, and the "good" solvents would be located inside the sphere, while the "poor" ones are located outside. Both the location of the sphere center and the sphere radius should be fitted according to the information on polymer swelling behavior in a number of solvents. According to the existing correlation between the capsule morphology and swelling behavior of polymers, the solvents located inside the solubility sphere of a polymer give capsules with compact morphologies. The solvents located outside the solubility sphere of the solvent give either core-shell or multicompartment capsules in combination with the chosen polymer. Once the solubility sphere of a polymer is found, the solubility/swelling behavior is approximated to all possible substances. HSP theory allows therefore prediction of polymer solubility/swelling behavior and consequently the capsule morphology for any given substance with known HSP parameters on the basis of limited data. The latter makes the theory so attractive for application in chemistry and technology, since the choice of the system components is usually performed on the basis of a large number of different parameters that should mutually match. Even slight change of the technology sometimes leads to the necessity to find the analogue of this or that solvent in a sense of solvency but carrying different chemistry. Usage of the HSP approach in this case is indispensable. In the second part of the work examples of the HSP application for the fabrication of capsules with on-demand-morphology are presented. Capsules with compact or core-shell morphology containing corrosion inhibitors were synthesized. Thus, alkoxysilanes possessing long hydrophobic tail, combining passivating and water-repelling properties, were encapsulated in polyurethane shell. The mechanism of action of the active material required core-shell morphology of the capsules. The new hybrid corrosion inhibitor, cerium diethylhexyl phosphate, was encapsulated in polyamide shells in order to facilitate the dispersion of the substance and improve its adhesion to the coating matrix. The encapsulation of commercially available antifouling agents in polyurethane shells was carried out in order to control its release behavior and colloidal stability. Capsules with compact morphology made of polyurea containing the liquid corrosion inhibitor 2-methyl benzothiazole were synthesized in order to improve the colloidal stability of the substance. Capsules with compact morphology allow slower release of the liquid encapsulated material compared to the core-shell ones. If the "in-situ" encapsulation is not possible due to the reaction of the oil-soluble monomer with the encapsulated material, a solution was proposed: loading of the capsules should be performed after monomer deactivation due to the accomplishment of the polymerization reaction. Capsules of desired morphologies should be preformed followed by the loading step. In this way, compact polyurea capsules containing the highly effective but chemically active corrosion inhibitors 8-hydroxyquinoline and benzotriazole were fabricated. All the resulting capsules were successfully introduced into model coatings. The efficiency of the resulting "smart" self-healing anticorrosion coatings on steel and aluminium alloy of the AA-2024 series was evaluated using characterization techniques such as Scanning Vibrating Electron Spectroscopy, Electrochemical Impedance Spectroscopy and salt-spray chamber tests.},
  language  = {en}
}
@phdthesis{Borisova2012,
  author    = {Borisova, Dimitriya},
  title     = {Feedback active coatings based on mesoporous silica containers},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-63505},
  school      = {Universit{\"a}t Potsdam},
  year      = {2012},
  abstract  = {Metalle werden oft w{\"a}hrend ihrer Anwendung korrosiven Bedingungen ausgesetzt, was ihre Alterungsbest{\"a}ndigkeit reduziert. Deswegen werden korrosionsanf{\"a}llige Metalle, wie Aluminiumlegierungen mit Schutzbeschichtungen versehen, um den Korrosionsprozess aktiv oder passiv zu verhindern. Die klassischen Schutzbeschichtungen funktionieren als physikalische Barriere zwischen Metall und korrosiver Umgebung und bieten einen passiven Korrosionsschutz nur, wenn sie unbesch{\"a}digt sind. Im Gegensatz dazu kann die Korrosion auch im Fall einer Besch{\"a}digung mittels aktiver Schutzbeschichtungen gehemmt werden. Chromathaltige Beschichtungen bieten heutzutage den besten aktiven Korrosionsschutz f{\"u}r Aluminiumlegierungen. Aufgrund ihrer Giftigkeit wurden diese weltweit verboten und m{\"u}ssen durch neue umweltfreundliche Schutzbeschichtungen ersetzt werden. Ein potentieller Ersatz sind Schutzbeschichtungen mit integrierten Nano- und Mikrobeh{\"a}ltern, die mit ungiftigem Inhibitor gef{\"u}llt sind. In dieser Arbeit werden die Entwicklung und Optimierung solcher aktiver Schutzbeschichtungen f{\"u}r die industriell wichtige Aluminiumlegierung AA2024-T3 dargestellt Mesopor{\"o}se Silika-Beh{\"a}lter wurden mit dem ungiftigen Inhibitor (2-Mercaptobenzothiazol) beladen und dann in die Matrix anorganischer (SiOx/ZrOx) oder organischer (wasserbasiert) Schichten dispergiert. Zwei Sorten von Silika-Beh{\"a}ltern mit unterschiedlichen Gr{\"o}ßen (d ≈ 80 and 700 nm) wurden verwendet. Diese haben eine große spezifische Oberfl{\"a}che (≈ 1000 m² g-1), eine enge Porengr{\"o}ßenverteilung mit mittlerer Porenweite ≈ 3 nm und ein großes Porenvolumen (≈ 1 mL g-1). Dank dieser Eigenschaften k{\"o}nnen große Inhibitormengen im Beh{\"a}lterinneren adsorbiert und gehalten werden. Die Inhibitormolek{\"u}le werden bei korrosionsbedingter Erh{\"o}hung des pH-Wertes gel{\"o}st und freigegeben. Die Konzentration, Position und Gr{\"o}ße der integrierten Beh{\"a}lter wurden variiert um die besten Bedingungen f{\"u}r einen optimalen Korrosionsschutz zu bestimmen. Es wurde festgestellt, dass eine gute Korrosionsschutzleistung durch einen Kompromiss zwischen ausreichender Inhibitormenge und guten Barriereeigenschaften hervorgerufen wird. Diese Studie erweitert das Wissen {\"u}ber die wichtigsten Faktoren, die den Korrosionsschutz beeinflussen. Somit wurde die Entwicklung effizienter, aktiver Schutzbeschichtungen erm{\"o}glicht, die auf mit Inhibitor beladenen Beh{\"a}ltern basieren.},
  language  = {en}
}
@phdthesis{Soulie2015,
  author    = {Souli{\´e}, Virginie},
  title     = {Sessile droplets of salt solutions on inert and metallic surfaces},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-90329},
  school      = {Universit{\"a}t Potsdam},
  year      = {2015},
  abstract  = {In this thesis we investigate the evaporation behaviour of sessile droplets of aqueous saline solutions on planar inert and metallic surfaces and characterise the corrosion phenomenon for iron surfaces. First we study the evaporation behaviour of sessile salty droplets on inert surfaces for a wide range of salt concentrations, relative humidities, droplet sizes and contact angles. Our study reveals the range of validity of the well-accepted diffusion-controlled evaporation model and highlights the impact of salt concentration (surface tension) gradients driven Marangoni flows on the evaporation behaviour and the subsequent salty deposit patterns. Furthermore we study the spatial-temporal evolution of sessile droplets from saline solutions on metallic surfaces. In contrast to the simple, generally accepted Evans droplet model, we show that the corrosion spreads ahead of the macroscopic contact line with a peripheral film. The three-phase contact line is destabilized by surface tension gradients induced by ionic composition changes during the course of the corrosion process and migration of cations towards the droplet perimeter. Finally we investigate the corrosion behaviour under drying salty sessile droplets on metallic surfaces. The corrosion process, in particular the location of anodic and cathodic activities over the footprint droplet area is correlated to the spatial distribution of the salt inside the drying droplet.},
  language  = {en}
}