@phdthesis{Tronci2010, author = {Tronci, Giuseppe}, title = {Synthesis, characterization, and biological evaluation of gelatin-based scaffolds}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-49727}, school = {Universit{\"a}t Potsdam}, year = {2010}, abstract = {This work presents the development of entropy-elastic gelatin based networks in the form of films or scaffolds. The materials have good prospects for biomedical applications, especially in the context of bone regeneration. Entropy-elastic gelatin based hydrogel films with varying crosslinking densities were prepared with tailored mechanical properties. Gelatin was covalently crosslinked above its sol gel transition, which suppressed the gelatin chain helicity. Hexamethylene diisocyanate (HDI) or ethyl ester lysine diisocyanate (LDI) were applied as chemical crosslinkers, and the reaction was conducted either in dimethyl sulfoxide (DMSO) or water. Amorphous films were prepared as measured by Wide Angle X-ray Scattering (WAXS), with tailorable degrees of swelling (Q: 300-800 vol. \%) and wet state Young's modulus (E: 70 740 kPa). Model reactions showed that the crosslinking reaction resulted in a combination of direct crosslinks (3-13 mol.-\%), grafting (5-40 mol.-\%), and blending of oligoureas (16-67 mol.-\%). The knowledge gained with this bulk material was transferred to the integrated process of foaming and crosslinking to obtain porous 3-D gelatin-based scaffolds. For this purpose, a gelatin solution was foamed in the presence of a surfactant, Saponin, and the resulting foam was fixed by chemical crosslinking with a diisocyanate. The amorphous crosslinked scaffolds were synthesized with varied gelatin and HDI concentrations, and analyzed in the dry state by micro computed tomography (µCT, porosity: 65±11-73±14 vol.-\%), and scanning electron microscopy (SEM, pore size: 117±28-166±32 µm). Subsequently, the work focused on the characterization of the gelatin scaffolds in conditions relevant to biomedical applications. Scaffolds showed high water uptake (H: 630-1680 wt.-\%) with minimal changes in outer dimension. Since a decreased scaffold pore size (115±47-130±49 µm) was revealed using confocal laser scanning microscopy (CLSM) upon wetting, the form stability could be explained. Shape recoverability was observed after removal of stress when compressing wet scaffolds, while dry scaffolds maintained the compressed shape. This was explained by a reduction of the glass transition temperature upon equilibration with water (dynamic mechanical analysis at varied temperature (DMTA)). The composition dependent compression moduli (Ec: 10 50 kPa) were comparable to the bulk micromechanical Young's moduli, which were measured by atomic force microscopy (AFM). The hydrolytic degradation profile could be adjusted, and a controlled decrease of mechanical properties was observed. Partially-degraded scaffolds displayed an increase of pore size. This was likely due to the pore wall disintegration during degradation, which caused the pores to merge. The scaffold cytotoxicity and immunologic responses were analyzed. The porous scaffolds enabled proliferation of human dermal fibroblasts within the implants (up to 90 µm depth). Furthermore, indirect eluate tests were carried out with L929 cells to quantify the material cytotoxic response. Here, the effect of the sterilization method (Ethylene oxide sterilization), crosslinker, and surfactant were analyzed. Fully cytocompatible scaffolds were obtained by using LDI as crosslinker and PEO40 PPO20-PEO40 as surfactant. These investigations were accompanied by a study of the endotoxin material contamination. The formation of medical-grade materials was successfully obtained (<0.5 EU/mL) by using low-endotoxin gelatin and performing all synthetic steps in a laminar flow hood.}, language = {en} } @article{CuiYashchenokZhangetal.2014, author = {Cui, Qianling and Yashchenok, Alexey and Zhang, Lu and Li, Lidong and Masic, Admir and Wienskol, Gabriele and Moehwald, Helmuth and Bargheer, Matias}, title = {Fabrication of Bifunctional Gold/Gelatin Hybrid Nanocomposites and Their Application}, series = {ACS applied materials \& interfaces}, volume = {6}, journal = {ACS applied materials \& interfaces}, number = {3}, publisher = {American Chemical Society}, address = {Washington}, issn = {1944-8244}, doi = {10.1021/am5000068}, pages = {1999 -- 2002}, year = {2014}, abstract = {Herein, a facile method is presented to integrate large gold nanoflowers (similar to 80 nm) and small gold nanoparticles (2-4 nm) into a single entity, exhibiting both surface-enhanced Raman scattering (SERS) and catalytic activity. The as-prepared gold nanoflowers were coated by a gelatin layer, in which the gold precursor was adsorbed and in situ reduced into small gold nanoparticles. The thickness of the gelatin shell is controlled to less than 10 nm, ensuring that the small gold nanoparticles are still in a SERS-active range of the inner Au core. Therefore, the reaction catalyzed by these nanocomposites can be monitored in situ using label-free SERS spectroscopy. In addition, these bifunctional nanocomposites are also attractive candidates for application in SERS monitoring of bioreactions because of their excellent biocompatibility.}, language = {en} } @article{BlockiLoewenbergJiangetal.2017, author = {Blocki, Anna and L{\"o}wenberg, Candy and Jiang, Yi and Kratz, Karl and Neffe, Axel T. and Jung, Friedrich and Lendlein, Andreas}, title = {Response of encapsulated cells to a gelatin matrix with varied bulk and microenvironmental elastic properties}, series = {Polymers for advanced technologies}, volume = {28}, journal = {Polymers for advanced technologies}, publisher = {Wiley}, address = {Hoboken}, issn = {1042-7147}, doi = {10.1002/pat.3947}, pages = {1245 -- 1251}, year = {2017}, abstract = {Gelatin-based hydrogels offer various biochemical cues that support encapsulated cells and are therefore suitable as cell delivery vehicles in regenerative medicine. However, besides the biochemical signals, biomechanical cues are crucial to ensure an optimal support of encapsulated cells. Hence, we aimed to correlate the cellular response of encapsulated cells to macroscopic and microscopic elastic properties of glycidylmethacrylate (GMA)-functionalized gelatin-based hydrogels. To ensure that different observations in cellular behavior could be attributed to differences in elastic properties, an identical concentration as well as degree of functionalization of biopolymers was utilized to form covalently crosslinked hydrogels. Elastic properties were merely altered by varying the average gelatin-chain length. Hydrogels exhibited an increased degree of swelling and a decreased bulk elastic modulus G with prolonged autoclaving of the starting solution. This was accompanied by an increase of hydrogel mesh size and thus by a reduction of crosslinking density. Tougher hydrogels retained the largest amount of cells; however, they also interfered with cell viability. Softer gels contained a lower cell density, but supported cell elongation and viability. Observed differences could be partially attributed to differences in bulk properties, as high crosslinking densities interfere with diffusion and cell spreading and thus can impede cell viability. Interestingly, a microscopic elastic modulus in the range of native soft tissue supported cell viability and elongation best while ensuring a good cell entrapment. In conclusion, gelatin-based hydrogels providing a soft tissue-like microenvironment represent adequate cell delivery vehicles for tissue engineering approaches. Copyright (c) 2016 John Wiley \& Sons, Ltd.}, language = {en} } @misc{SchneiderGuenterTaubert2018, author = {Schneider, Matthias and G{\"u}nter, Christina and Taubert, Andreas}, title = {Co-deposition of a hydrogel/calcium phosphate hybrid layer on 3D printed poly(lactic acid) scaffolds via dip coating}, series = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, journal = {Postprints der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, number = {1057}, issn = {1866-8372}, doi = {10.25932/publishup-47442}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-474427}, pages = {21}, year = {2018}, abstract = {The article describes the surface modification of 3D printed poly(lactic acid) (PLA) scaffolds with calcium phosphate (CP)/gelatin and CP/chitosan hybrid coating layers. The presence of gelatin or chitosan significantly enhances CP co-deposition and adhesion of the mineral layer on the PLA scaffolds. The hydrogel/CP coating layers are fairly thick and the mineral is a mixture of brushite, octacalcium phosphate, and hydroxyapatite. Mineral formation is uniform throughout the printed architectures and all steps (printing, hydrogel deposition, and mineralization) are in principle amenable to automatization. Overall, the process reported here therefore has a high application potential for the controlled synthesis of biomimetic coatings on polymeric biomaterials.}, language = {en} } @article{SchneiderGuenterTaubert2018, author = {Schneider, Matthias and G{\"u}nter, Christina and Taubert, Andreas}, title = {Co-deposition of a hydrogel/calcium phosphate hybrid layer on 3D printed poly(lactic acid) scaffolds via dip coating}, series = {Polymers}, volume = {10}, journal = {Polymers}, number = {3}, publisher = {MDPI}, address = {Basel}, issn = {2073-4360}, doi = {10.3390/polym10030275}, pages = {19}, year = {2018}, abstract = {The article describes the surface modification of 3D printed poly(lactic acid) (PLA) scaffolds with calcium phosphate (CP)/gelatin and CP/chitosan hybrid coating layers. The presence of gelatin or chitosan significantly enhances CP co-deposition and adhesion of the mineral layer on the PLA scaffolds. The hydrogel/CP coating layers are fairly thick and the mineral is a mixture of brushite, octacalcium phosphate, and hydroxyapatite. Mineral formation is uniform throughout the printed architectures and all steps (printing, hydrogel deposition, and mineralization) are in principle amenable to automatization. Overall, the process reported here therefore has a high application potential for the controlled synthesis of biomimetic coatings on polymeric biomaterials.}, language = {en} } @article{LoewenbergTripodoJulichGruneretal.2020, author = {L{\"o}wenberg, Candy and Tripodo, Giuseppe and Julich-Gruner, Konstanze K. and Neffe, Axel T. and Lendlein, Andreas}, title = {Supramolecular gelatin networks based on inclusion complexes}, series = {Macromolecular bioscience}, volume = {20}, journal = {Macromolecular bioscience}, number = {10}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1616-5187}, doi = {10.1002/mabi.202000221}, pages = {8}, year = {2020}, abstract = {Hydrogel forming physical networks based on gelatin are an attractive approach toward multifunctional biomaterials with the option of reshaping, self-healing, and stimuli-sensitivity. However, it is challenging to design such gelatin-based hydrogels to be stable at body temperature. Here, gelatin functionalized with desaminotyrosine (DAT) or desaminotyrosyl tyrosine (DATT) side chains is crosslinked with cyclodextrin (CD) dimers under formation of inclusions complexes. The supramolecular networks displayed at room temperature decreased water uptake (200-600 wt\% for DAT-based systems, 200 wt\% for DATT based systems), and increased storage moduli up to 25.6 kPa determined by rheology compared to DAT(T) gelatin. The gel-sol transition temperature increased from 33 up to 42 degrees C. The presented system that is completely based on natural building blocks may form the basis for materials that may potentially respond by dissolution or changes of properties to changes in environmental conditions or to the presence of CD guest molecules.}, language = {en} }