@article{AltafimRychkovWirgesetal.2012, author = {Altafim, Ruy Alberto Pisani and Rychkov, Dmitry and Wirges, Werner and Gerhard, Reimund and Basso, Heitor Cury and Altafim, Ruy Alberto Pisani and Melzer, Martin}, title = {Laminated tubular-channel ferroelectret systems from low-density Polyethylene Films and from Fluoroethylene-propylene Copolymer Films - A comparison}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {19}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {4}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, pages = {1116 -- 1123}, year = {2012}, abstract = {A template-based lamination technique for the manufacture of ferroelectrets from uniform electret films was recently reported. In the present work, this technique is used to prepare similar ferroelectret structures from low-density polyethylene (LDPE) films and from fluoro-ethylene-propylene (FEP) copolymer films. A comparative analysis of the pressure-, temperature-, and frequency-dependent piezoelectric properties has been performed on the two ferroelectret systems. It is observed that the FEP ferroelectrets exhibit better piezoelectric responses and are thermally more stable. The difference between the piezoelectric d(33) coefficients of the two ferroelectret systems is partially explained here by their different elastic moduli. The anti-resonance peaks of both structures have been investigated by means of dielectric resonance spectroscopy and electroacoustic sound-pressure measurements. A difference of more than 10 kHz is observed between the anti-resonance frequencies of the two ferroelectret systems.}, language = {en} } @article{AssagraAltafimdoCarmoetal.2020, author = {Assagra, Yuri A.O. and Altafim, Ruy Alberto Pisani and do Carmo, Joao P. and Altafim, Ruy A.C. and Rychkov, Dmitry and Wirges, Werner and Gerhard, Reimund}, title = {A new route to piezo-polymer transducers: 3D printing of polypropylene ferroelectrets}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {27}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {5}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2020.008461}, pages = {1668 -- 1674}, year = {2020}, abstract = {Here, a promising approach for producing piezo-polymer transducers in a one-step process is presented. Using 3D-printing technology and polypropylene (PP) filaments, we are able to print a two-layered film structure with regular cavities of precisely controlled size and shape. It is found that the 3D-printed samples exhibit piezoelectric coefficients up to 200 pC/N, similar to those of other PP ferroelectrets, and their temporal and thermal behavior is in good agreement with those known of PP ferroelectrets. The piezoelectric response strongly decreases for applied pressures above 20 kPa, as the pressure in the air-filled cavities strongly influences the overall elastic modulus of ferroelectrets.}, language = {en} } @misc{CheilakouTsopelasAnastasopoulosetal.2018, author = {Cheilakou, E. and Tsopelas, N. and Anastasopoulos, A. and Kourousis, D. and Rychkov, Dmitry and Gerhard, Reimund and Frankenstein, B. and Amditis, A. and Damigos, Y. and Bouklas, C.}, title = {Strain monitoring system for steel and concrete structures}, series = {Procedia Structural Integrity}, volume = {10}, journal = {Procedia Structural Integrity}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2452-3216}, doi = {10.1016/j.prostr.2018.09.005}, pages = {25 -- 32}, year = {2018}, abstract = {The present work is part of a collaborative H2020 European funded research project called SENSKIN, that aims to improve Structural Health Monitoring (SHM) for transport infrastructure through the development of an innovative monitoring and management system for bridges based on a novel, inexpensive, skin-like sensor. The integrated SENSKIN technology will be implemented in the case of steel and concrete bridges, and tested, field-evaluated and benchmarked on actual bridge environment against a conventional health monitoring solution developed by Mistras Group Hellas. The main objective of the present work is to implement the autonomous, fully functional strain monitoring system based on commercially available off-the-shelf components, that will be used to accomplish direct comparison between the performance of the innovative SENSKIN sensors and the conventional strain sensors commonly used for structural monitoring of bridges. For this purpose, the mini Structural Monitoring System (mini SMS) of Physical Acoustics Corporation, a comprehensive data acquisition unit designed specifically for long-term unattended operation in outdoor environments, was selected. For the completion of the conventional system, appropriate foil-type strain sensors were selected, driven by special conditioners manufactured by Mistras Group. A comprehensive description of the strain monitoring system and its peripheral components is provided in this paper. For the evaluation of the integrated system's performance and the effect of various parameters on the long-term behavior of sensors, several test steel pieces instrumented with different strain sensors configurations were prepared and tested in both laboratory and field ambient conditions. Furthermore, loading tests were performed aiming to validate the response of the system in monitoring the strains developed in steel beam elements subject to bending regimes. Representative results obtained from the above experimental tests have been included in this paper as well.}, language = {en} } @misc{LouposDamigosAmditisetal.2017, author = {Loupos, Konstantinos and Damigos, Yannis and Amditis, Angelos and Gerhard, Reimund and Rychkov, Dmitry and Wirges, Werner and Schulze, Manuel and Lenas, Sotiris-Angelos and Chatziandreoglou, Christos and Malliou, Christina and Tsaoussidis, Vassilis and Brady, Ken and Frankenstein, Bernd}, title = {Structural health monitoring system for bridges based on skin-like sensor}, series = {IOP conference series : Materials science and engineering}, volume = {236}, journal = {IOP conference series : Materials science and engineering}, publisher = {IOP Publ. Ltd.}, address = {Bristol}, issn = {1757-8981}, doi = {10.1088/1757-899X/236/1/012100}, pages = {10}, year = {2017}, abstract = {Structural health monitoring activities are of primal importance for managing transport infrastructure, however most SHM methodologies are based on point-based sensors that have limitations in terms of their spatial positioning requirements, cost of development and measurement range. This paper describes the progress on the SENSKIN EC project whose objective is to develop a dielectric-elastomer and micro-electronics-based sensor, formed from a large highly extensible capacitance sensing membrane supported by advanced microelectronic circuitry, for monitoring transport infrastructure bridges. Such a sensor could provide spatial measurements of strain in excess of 10\%. The actual sensor along with the data acquisition module, the communication module and power electronics are all integrated into a compact unit, the SENSKIN device, which is energy-efficient, requires simple signal processing and it is easy to install over various surface types. In terms of communication, SENSKIN devices interact with each other to form the SENSKIN system; a fully distributed and autonomous wireless sensor network that is able to self-monitor. SENSKIN system utilizes Delay-/Disruption-Tolerant Networking technologies to ensure that the strain measurements will be received by the base station even under extreme conditions where normal communications are disrupted. This paper describes the architecture of the SENSKIN system and the development and testing of the first SENSKIN prototype sensor, the data acquisition system, and the communication system.}, language = {en} } @misc{LouposDamigosTsertouetal.2019, author = {Loupos, Konstantinos and Damigos, Yannis and Tsertou, Athanasisa and Amditis, Angelos and Lenas, Sotiris-Angelos and Chatziandreoglou, Chistos and Malliou, Christina and Tsaoussidis, Vassilis and Gerhard, Reimund and Rychkov, Dmitry and Wirges, Werner and Frankenstein, Bernd and Camarinopoulos, Stephanos and Kalidromitis, Vassilis and Sanna, C. and Maier, Stephanos and Gordt, A. and Panetsos, P.}, title = {Innovative soft-material sensor, wireless network and assessment software for bridge life-cycle assessment}, series = {Life-cycle analysis and assessmanet in civil engineering : towards an integrated vision}, journal = {Life-cycle analysis and assessmanet in civil engineering : towards an integrated vision}, publisher = {CRC Press, Taylor \& Francis Group}, address = {Boca Raton}, isbn = {978-1-315-22891-4}, pages = {2085 -- 2092}, year = {2019}, abstract = {Nowadays, structural health monitoring of critical infrastructures is considered as of primal importance especially for managing transport infrastructure however most current SHM methodologies are based on point-sensors that show various limitations relating to their spatial positioning capabilities, cost of development and measurement range. This publication describes the progress in the SENSKIN EC co-funded research project that is developing a dielectric-elastomer sensor, formed from a large highly extensible capacitance sensing membrane and is supported by an advanced micro-electronic circuitry, for monitoring transport infrastructure bridges. The sensor under development provides spatial measurements of strain in excess of 10\%, while the sensing system is being designed to be easy to install, require low power in operation concepts, require simple signal processing, and have the ability to self-monitor and report. An appropriate wireless sensor network is also being designed and developed supported by local gateways for the required data collection and exploitation. SENSKIN also develops a Decision-Support-System (DSS) for proactive condition-based structural interventions under normal operating conditions and reactive emergency intervention following an extreme event. The latter is supported by a life-cycle-costing (LCC) and life-cycle-assessment (LCA) module responsible for the total internal and external costs for the identified bridge rehabilitation, analysis of options, yielding figures for the assessment of the economic implications of the bridge rehabilitation work and the environmental impacts of the bridge rehabilitation options and of the associated secondary effects respectively. The overall monitoring system will be evaluated and benchmarked on actual bridges of Egnatia Highway (Greece) and Bosporus Bridge (Turkey).}, language = {en} } @article{McCarthyStoyanovRychkovetal.2012, author = {McCarthy, Denis N. and Stoyanov, Hristiyan and Rychkov, Dmitry and Ragusch, Huelya and Melzer, Michael and Kofod, Guggi}, title = {Increased permittivity nanocomposite dielectrics by controlled interfacial interactions}, series = {Composites science and technology}, volume = {72}, journal = {Composites science and technology}, number = {6}, publisher = {Elsevier}, address = {Oxford}, issn = {0266-3538}, doi = {10.1016/j.compscitech.2012.01.026}, pages = {731 -- 736}, year = {2012}, abstract = {The use of nanoparticles in polymer composite dielectrics has promised great improvements, but useful results have been elusive. Here, the importance of the interfacial interactions between the nanoparticles and the polymer matrix are investigated in TiO2 nanocomposites for dielectric materials using surface functionalisation. The interface is observed to dominate the nanocomposite properties and leads to a threefold increase in permittivity at volume fractions as low as 10\%. Surface functionalisation of the filler nanoparticles with silanes allows control of this interface, avoiding significant degradation of the other important material properties, particularly electrical breakdown strength, and resulting in a material that is demonstrated successfully as an active material in a dielectric elastomer actuator application with increased work output compared to the pure polymer. Although further permittivity increases are observed when the interface regions have formed a percolation network, the other material properties deteriorate. The observation of percolation behaviour allows the interface thickness to be estimated.}, language = {en} } @misc{NguyenWangRychkovetal.2019, author = {Nguyen, Quyet Doan and Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Depth Profile and Transport of Positive and Negative Charge in Surface (2-D) and Bulk (3-D) Nanocomposite Films}, series = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, journal = {2nd International Conference on Electrical Materials and Power Equipment (ICEMPE 2019)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-8434-4}, doi = {10.1109/ICEMPE.2019.8727256}, pages = {298 -- 300}, year = {2019}, abstract = {In the present study, the charge distribution and the charge transport across the thickness of 2- and 3-dimensional polymer nanodielectrics was investigated. Chemically surface-treated polypropylene (PP) films and low-density polyethylene nanocomposite films with 3 wt \% of magnesium oxide (LDPE/MgO) served as examples of 2-D and 3-D nanodielectrics, respectively. Surface charges were deposited onto the non-metallized surfaces of the one-side metallized polymer films and found to broaden and to thus enter the bulk of the films upon thermal stimulation at suitable elevated temperatures. The resulting space-charge profiles in the thickness direction were probed by means of Piezoelectrically-generated Pressure Steps (PPSs). It was observed that the chemical surface treatment of PP which led to the formation of nano-structures or the use of bulk nanoparticles from LDPE/MgO nanocomposites enhance charge trapping on or in the respective polymer films and also reduce charge transport inside the respective samples.}, language = {en} } @misc{RychkovStojharovKuznetsovetal.2018, author = {Rychkov, Andrey and Stojharov, Valery and Kuznetsov, Alexey and Rychkov, Dmitry}, title = {The influence of recrystallization regimes on electret charge stability in low-density polyethylene films}, series = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, journal = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6389-9}, doi = {10.1109/ICD.2018.8514638}, pages = {4}, year = {2018}, abstract = {The electret state stability in nonpolar semicrystalline polymers is largely determined by the traps located at crystalline/ amorphous phase interfaces. Thus, the thermal history of such polymers should considerably influence their electret properties. In the present work, we investigate how recrystallization influences charge stability in low-density polyethylene corona electrets. It has been found that electret charge stability in quenched samples is higher than in slowly-crystallized ones. Phenomenologicaly, this can be explained by the increased number of deeper traps in samples with smaller crystallite size.}, language = {en} } @article{RychkovAltafim2018, author = {Rychkov, Dmitry and Altafim, Ruy Alberto Pisani}, title = {Template-based fluoroethylenepropylene ferroelectrets with enhanced thermal stability of piezoelectricity}, series = {Journal of applied physics}, volume = {124}, journal = {Journal of applied physics}, number = {17}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/1.5041374}, pages = {5}, year = {2018}, abstract = {In ferroelectrets, the piezoelectricity stems from the charges of both polarities trapped on the inner surfaces of the cavities in the material, so that its thermal stability is defined by the stability of the respective charges. In the present work, a template-based lamination technique has been employed to fabricate tubular-channel ferroelectrets from fluoroethylenepropylene (FEP) films. It has been shown that the piezoelectricity in FEP ferroelectrets decays at relatively low temperatures due to the inherently lower thermal stability of the positive charge. In order to improve charge trapping, we have treated both FEP films and inner surfaces of the ferroelectret cavities with titanium-tetrachloride vapor, using the atomic-layer-deposition technique. Using surface-potential-decay measurements on FEP films, we have found that the charge-decay curves shift by more than 100 degrees C to the higher temperatures as a result of the surface treatment. Direct measurements of piezoelectric d(33) coefficients as a function of temperature have shown that the piezoelectric stability is likewise improved with the d(33)-decay curves shifted by 60 degrees C to the right. The improvement of electret/ferroelectret properties can be attributed to the formation of the deeper traps on the chemically modified FEP surface. SEM micrographs and EDS analysis reveal island-like structures with titanium- and oxygen-containing species that can be responsible for the deeper trapping of the electret charges. Published by AIP Publishing.}, language = {en} } @article{RychkovAltafimQiuetal.2012, author = {Rychkov, Dmitry and Altafim, Ruy Alberto Pisani and Qiu, Xunlin and Gerhard, Reimund}, title = {Treatment with orthophosphoric acid enhances the thermal stability of the piezoelectricity in low-density polyethylene ferroelectrets}, series = {Journal of applied physics}, volume = {111}, journal = {Journal of applied physics}, number = {12}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/1.4729866}, pages = {5}, year = {2012}, abstract = {Ferroelectrets have been fabricated from low-density polyethylene (LDPE) films by means of a template-based lamination. The temperature dependence of the piezoelectric d(33) coefficient has been investigated. It was found that low-density polyethylene ferroelectrets have rather low thermal stability with the piezoelectric coefficient decaying almost to zero already at 100 degrees C. This behavior is attributed to the poor electret properties of the polyethylene films used for the fabrication of the ferroelectrets. In order to improve the charge trapping and the thermal stability of electret charge and piezoelectricity, LDPE ferroelectrets were treated with orthophosphoric acid. The treatment resulted in considerable improvements of the charge stability in LDPE films and in ferroelectret systems made from them. For example, the charge and piezoelectric-coefficient decay curves shifted to higher temperatures by 60 K and 40 K, respectively. It is shown that the decay of the piezoelectric coefficient in LDPE ferroelectrets is governed by the relaxation of less stable positive charges. The treatment also leads to noticeable changes in the chemical composition of the LDPE surface. Infrared spectroscopy reveals absorption bands attributed to phosphorus-containing structures, while scanning electron microscopy shows new island-like structures, 50-200 nm in diameter, on the modified surface.}, language = {en} } @article{RychkovGerhard2011, author = {Rychkov, Dmitry and Gerhard, Reimund}, title = {Stabilization of positive charge on polytetrafluoroethylene electret films treated with titanium-tetrachloride vapor}, series = {Applied physics letters}, volume = {98}, journal = {Applied physics letters}, number = {12}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0003-6951}, doi = {10.1063/1.3565166}, pages = {3}, year = {2011}, abstract = {The surface of polytetrafluoroethylene films was treated with titanium-tetrachloride vapor. The treatment was carried out in a flow reactor by means of molecular-layer deposition, a method from the arsenal of chemical nanotechnology. X-ray photoelectron spectroscopy reveals that such a treatment results in considerable changes in the chemical composition at and near the surface of the fluoropolymer film. Both, defluorination and oxidation of the surface were observed. At the same time, samples treated with titanium tetrachloride show a significant enhancement in the thermal stability of the positive homocharge. The thermally stimulated surface-potential-decay curves were observed to shift to higher temperatures by more than 100 degrees C.}, language = {en} } @article{RychkovGerhardIvanovetal.2012, author = {Rychkov, Dmitry and Gerhard, Reimund and Ivanov, Vadim and Rychkov, Andrey}, title = {Enhanced electret charge stability on Polyethylene Films treated with Titanium-Tetrachloride vapor}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {19}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {4}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, pages = {1305 -- 1311}, year = {2012}, abstract = {Low-density polyethylene (LDPE) films have been treated with titanium-tetrachloride vapor by means of the molecular-layer-deposition method. It is shown that such a treatment leads to a considerable improvement of the electret properties for both positively and negatively charged films. The temperature stability of the electret homo-charge has been increased by approximately 60 degrees C. At the same time, the temporal stability of charge is also considerably improved. Modified low-density polyethylene films show no "cross-over phenomenon" when charged to higher voltages. Thus, it is now possible to produce electrets from polyethylene films with high initial charge densities, but without a strongly reduced charge stability. The influence of a chemical treatment with titanium-tetrachloride vapor on charge injection from aluminum electrodes into polyethylene films was also investigated. It is found that the interface between an aluminum electrode and a modified LDPE surface layer has different injection properties for positive and negative charges. Electrons can be injected across the modified interface, whereas injection of holes is either very limited or non-existent.}, language = {en} } @article{RychkovGerhardKuznetsovetal.2018, author = {Rychkov, Dmitry and Gerhard, Reimund and Kuznetsov, Alexey and Rychkov, Andrey}, title = {Influence of charge density on the trap energy spectrum in fluoroethylenepropylene copolymer films with chemically modified surfaces}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {25}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {3}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2018.007437}, pages = {840 -- 844}, year = {2018}, abstract = {Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps.}, language = {en} } @article{RychkovKuznetsovRychkov2011, author = {Rychkov, Dmitry and Kuznetsov, Alexey and Rychkov, Andrey}, title = {Electret properties of polyethylene and polytetrafluoroethylene films with chemically modified surface}, series = {IEEE transactions on dielectrics and electrical insulation}, volume = {18}, journal = {IEEE transactions on dielectrics and electrical insulation}, number = {1}, publisher = {Inst. of Electr. and Electronics Engineers}, address = {Piscataway}, issn = {1070-9878}, doi = {10.1109/TDEI.2011.5704487}, pages = {8 -- 14}, year = {2011}, abstract = {This paper investigates the effect of chemical surface modification of polytetrafluoroethylene (PTFE) and low density polyethylene (LDPE) films on their electret properties. PTFE films were subjected to wet treatment with three different chemicals: orthophosphoric acid, tetrabutyl titanate and tetraethoxysilane. The technique based on the principles of molecular layer deposition (MLD) method was used to modify the surface of LDPE films with phosphorus trichloride vapors. The surfaces of the films were then corona charged, and the electret charge stability was studied by means of isothermal and thermally stimulated surface potential decay. Both PTFE and LDPE films, after the surface treatment, displayed a considerable enhancement in the charge stability compared to the virgin samples. It is important to note that the enhancement of the charge stability was achieved in the positively charged PTFE films, a result important to practical applications. We attribute this effect of charge stabilization to the formation of new energetically deep traps on the modified surface. Decrease in molecular mobility, due to attachment of new chemical structures to the surface macromolecules, may also contribute to the overall growth of the charge stability.}, language = {en} } @article{RychkovRychkovEfimovetal.2013, author = {Rychkov, Dmitry and Rychkov, A. and Efimov, N. and Malygin, A. and Gerhard, Reimund}, title = {Higher stabilities of positive and negative charge on tetrafluoroethylene-hexafluoropropylene copolymer (FEP) electrets treated with titanium-tetrachloride vapor}, series = {Applied physics : A, Materials science \& processing}, volume = {112}, journal = {Applied physics : A, Materials science \& processing}, number = {2}, publisher = {Springer}, address = {New York}, issn = {0947-8396}, doi = {10.1007/s00339-013-7821-1}, pages = {283 -- 287}, year = {2013}, abstract = {Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor in a molecular-layer deposition process. As a result of the surface treatment, significant improvements of the thermal and temporal charge stability were observed. Charge-decay measurements revealed enhancements of the half-value temperatures and the relaxation times of positively charged FEP electrets by at least 120 A degrees C and two orders of magnitude, respectively. Beyond previous publications on fluoropolymer electrets with surface modification, we here report enhanced charge stabilities of the FEP films charged in negative as well as in positive corona discharges. Even though the improvement for negatively charged FEP films is moderate (half-value temperature about 20 A degrees C higher), our experiments show that the asymmetry in positive and negative charge stability that is typical for FEP electrets can be overcome by means of chemical surface treatments. The results are discussed in the context of the formation of modified surface layers with enhanced charge-trapping properties.}, language = {en} } @article{RychkovYablokovRychkov2012, author = {Rychkov, Dmitry and Yablokov, M. and Rychkov, A.}, title = {Chemical and physical surface modification of PTFE films-an approach to produce stable electrets}, series = {Applied physics : A, Materials science \& processing}, volume = {107}, journal = {Applied physics : A, Materials science \& processing}, number = {3}, publisher = {Springer}, address = {New York}, issn = {0947-8396}, doi = {10.1007/s00339-012-6834-5}, pages = {589 -- 596}, year = {2012}, abstract = {The thermal stability of positive charge has been investigated in chemically and physically treated polytetrafluoroethylene (PTFE) films. It has been found that virgin films, oriented by the manufacturer, display an increase in thermal stability of positive charge with an increase of the initial value of surface potential. Such an anomalous behavior is explained by the influence of a negative tribocharge, trapped some small distance below the surface. In PTFE samples treated with orthophosphoric acid and with tetraethoxysilane, a considerable improvement of positive charge stability has been achieved, but no influence of the initial value of surface potential has been observed. However, this influence should be kept in mind when comparing charge stability in virgin and modified samples. In nonoriented PTFE films, no influence of the initial value of surface potential on charge stability has been observed. This could be due to the fact that these films did not possess a noticeable negative tribocharge. After the treatment in glow-discharge defluorination, oxidation and appearance of polar groups have been detected on the surface. These changes in chemical composition of a PTFE surface resulted in a noticeable improvement in thermal stability of positively charged electrets. This improvement is attributed to the formation of deeper traps on the modified surface.}, language = {en} } @article{WangRychkovGerhard2017, author = {Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Chemical modification with orthophosphoric acid enhances surface-charge stability on polypropylene electrets}, series = {Applied physics letters}, volume = {110}, journal = {Applied physics letters}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0003-6951}, doi = {10.1063/1.4983348}, pages = {5}, year = {2017}, abstract = {The low surface-charge stability of polypropylene (PP) frequently limits its application as an electret material. In this paper, we demonstrate how the treatment of PP-film surfaces with orthophosphoric acid (H3PO4) enhances their charge stability. To discriminate between the effects of chemical modification and thermal treatment, as-received and annealed PP films are used as reference samples. The electret properties of treated and non-treated PP films are characterized with thermally stimulated discharge (TSD) and isothermal surface-potential decay (ISPD) experiments, from which considerable improvement in thermal and temporal charge stability is observed for samples modified with H3PO4. The half-value temperature (T-1/2) observed on TSD curves of chemically treated PP increases to 131 and 145 degrees C for positive and negative charges, respectively. The enhancement might be attributed to the phosphoric compounds detected on the H3PO4-modified surfaces via attenuated-total-reflection infrared spectroscopy. Deeper surface traps formed at the "foreign" phosphorus-containing structures are able to capture the charges over longer time periods and at higher temperatures, thus leading to significant improvements in the temporal and thermal surface-charge stabilities of PP electrets. Published by AIP Publishing.}, language = {en} } @misc{WangRychkovGerhard2018, author = {Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Influence of Charge Density on Charge Decay in Chemically Modified Polypropylene Films}, series = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, journal = {2018 IEEE 2nd International Conference on Dielectrics (ICD)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6389-9}, doi = {10.1109/ICD.2018.8514718}, pages = {4}, year = {2018}, abstract = {Previous work has shown that surface modification with orthophosphoric acid can significantly enhance the charge stability on polypropylene (PP) surface by generating deeper traps. In the present study, thermally stimulated potential-decay measurements revealed that the chemical treatment may also significantly increase the number of available trapping sites on the surface. Thus, as a consequence, the so-called "cross-over" phenomenon, which is observed on as-received and thermally treated PP electrets, may be overcome in a certain range of initial charge densities. Furthermore, the discharge behavior of chemically modified samples indicates that charges can be injected from the treated surface into the bulk, and/or charges of opposite polarity can be pulled from the rear electrode into the bulk at elevated temperatures and at the high electric fields that are caused by the deposited charges. In the bulk, a lack of deep traps causes rapid charge decay already in the temperature range around 95 degrees C.}, language = {en} } @article{WangRychkovGerhard2021, author = {Wang, Jingwen and Rychkov, Dmitry and Gerhard, Reimund}, title = {Space-charge electret properties of polypropylene films with transcrystalline or spherulitic structures}, series = {Journal of applied physics : AIP's archival journal for significant new results in applied physics / publ. by the American Institute of Physics}, volume = {129}, journal = {Journal of applied physics : AIP's archival journal for significant new results in applied physics / publ. by the American Institute of Physics}, number = {6}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/5.0039867}, pages = {7}, year = {2021}, abstract = {Spherulite-related space-charge electret properties of polypropylene (PP) have been widely discussed in the past decades. In the present paper, a less-common crystalline structure in PP-transcrystalline PP-is studied regarding its electret behavior in comparison with the typical spherulitic morphology. Polarized light microscopy and differential scanning calorimetry were employed to characterize the crystallite types and crystallinities of transcrystalline and spherulitic PP. Their electret functionality is investigated by means of thermally stimulated discharge experiments, where the cross-over phenomenon is observed on transcrystalline PP films, whereas surface-potential saturation and undercharging on the surface occur on the spherulitic samples. Besides, an asymmetrical behavior of positive and negative surface-charge stabilities is found on PP with spherulites, the negatively charged spherulitic surfaces show a better charge stability. It is shown that PP electrets are very sensitive to changes in the microscopic crystalline structures and their interfaces as well as in the molecular conformations controlled through adjustments of the respective processing steps. In addition, surface and bulk nanocomposites of PP or low-density polyethylene with inorganic particles are included in the comparison. In view of recent developments in the areas of PP-based electret-fiber filters and cellular-foam ferroelectrets, the observed changes in the charge-storage properties may have particular relevance, as the required film, fiber, or foam processing might significantly modify crystalline morphologies and nano-scale interfaces in PP electrets. Limitations in the charge-storage capabilities of interface structures may also be of interest in the context of high-voltage electrical-insulation materials where reduced space-charge accumulation and slightly increased charge transport can be advantageous.}, language = {en} } @article{WangRychkovNguyenetal.2020, author = {Wang, Jingwen and Rychkov, Dmitry and Nguyen, Quyet Doan and Gerhard, Reimund}, title = {The influence of orthophosphoric-acid surface modification on charge-storage enhancement in polypropylene electrets}, series = {Journal of applied physics}, volume = {128}, journal = {Journal of applied physics}, number = {3}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-8979}, doi = {10.1063/5.0013805}, pages = {6}, year = {2020}, abstract = {Bipolar electrets from polypropylene (PP) are essential, e.g., in electret air filters and in cellular-foam ferroelectrets. Therefore, the mechanism of surface-charge stability enhancement on PP electrets via orthophosphoric-acid surface treatment is investigated in detail. It is shown that the significant charge-stability enhancement can be mainly attributed to deeper surface traps originating from deposited chemicals and topographic features on the modified surfaces. Thermally stimulated discharge of chemically treated and non-treated PP films with different surface-charge densities is used to test the limits of the newly formed deep traps in terms of the capacity for hosting surface charges. When the initial surface-charge density is very high, more charges are forced into shallower original traps on the surface or in the bulk of the treated PP samples, reducing the effect of the deeper surface traps brought by the surface modification. The well-known crossover phenomenon (of the surface-charge decay curves) has been observed between modified PP electrets charged to +/- 2kV and to +/- 3kV. Acoustically probed charge distributions in the thickness direction of PP electrets at different stages of thermal discharging indicate that the deep surface trapping sites may have preference for negative charges, resulting in the observed asymmetric charge stability of the modified PP films.}, language = {en} }