@article{AbdouAlonsoBrunetal.2022,
  author    = {Abdou, Nicole and Alonso, Bruno and Brun, Nicolas and Landois, Perine and Taubert, Andreas and Hesemann, Peter and Mehdi, Ahmad},
  title     = {Ionic guest in ionic host},
  series = {Materials chemistry frontiers},
  volume    = {6},
  journal   = {Materials chemistry frontiers},
  number    = {7},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {2052-1537},
  doi       = {10.1039/d2qm00021k},
  pages     = {939 -- 947},
  year      = {2022},
  abstract  = {Ionosilica ionogels, i.e. composites consisting of an ionic liquid (IL) guest confined in an ionosilica host matrix, were synthesized via a non-hydrolytic sol-gel procedure from a tris-trialcoxysilylated amine precursor using the IL [BMIM]NTf2 as solvent. Various ionosilica ionogels were prepared starting from variable volumes of IL in the presence of formic acid. The resulting brittle and nearly colourless monoliths are composed of different amounts of IL guests confined in an ionosilica host as evidenced via thermogravimetric analysis, FT-IR, and C-13 CP-MAS solid-state NMR spectroscopy. In the following, we focused on confinement effects between the ionic host and guest. Special host-guest interactions between the IL guest and the ionosilica host were evidenced by H-1 solid-state NMR, Raman spectroscopy, and broadband dielectric spectroscopy (BDS) measurements. The three techniques indicate a strongly reduced ion mobility in the ionosilica ionogel composites containing small volume fractions of confined IL, compared to conventional silica-based ionogels. We conclude that the ionic ionosilica host stabilizes an IL layer on the host surface; this then results in a strongly reduced ion mobility compared to conventional silica hosts. The ion mobility progressively increases for systems containing higher volume fractions of IL and finally reaches the values observed in conventional silica based ionogels. These results therefore point towards strong interactions and confinement effects between the ionic host and the ionic guest on the ionosilica surface. Furthermore, this approach allows confining high volume fractions of IL into self-standing monoliths while preserving high ionic conductivity. These effects may be of interest in domains where IL phases must be anchored on solid supports to avoid leaching or IL spilling, e.g., in catalysis, in gas separation/sequestration devices or for the elaboration of solid electrolytes for (lithium-ion) batteries and supercapacitors.},
  language  = {en}
}
@article{AbouserieZehbeMetzneretal.2017,
  author    = {Abouserie, Ahed and Zehbe, Kerstin and Metzner, Philipp and Kelling, Alexandra and G{\"u}nter, Christina and Schilde, Uwe and Strauch, Peter and K{\"o}rzd{\"o}rfer, Thomas and Taubert, Andreas},
  title     = {Alkylpyridinium Tetrahalidometallate Ionic Liquids and Ionic Liquid Crystals: Insights into the Origin of Their Phase Behavior},
  series = {European journal of inorganic chemistry : a journal of ChemPubSoc Europe},
  journal   = {European journal of inorganic chemistry : a journal of ChemPubSoc Europe},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1434-1948},
  doi       = {10.1002/ejic.201700826},
  pages     = {5640 -- 5649},
  year      = {2017},
  abstract  = {Six N-alkylpyridinium salts [CnPy](2)[MCl4] (n = 4 or 12 and M = Co, Cu, Zn) were synthesized, and their structure and thermal properties were studied. The [C4Py](2)[MCl4] compounds are monoclinic and crystallize in the space group P2(1)/n. The crystals of the longer chain analogues [C12Py](2)[MCl4] are triclinic and crystallize in the space group P (1) over bar. Above the melting temperature, all compounds are ionic liquids (ILs). The derivatives with the longer C12 chain exhibit liquid crystallinity and the shorter chain compounds only show a melting transition. Consistent with single-crystal analysis, electron paramagnetic resonance spectroscopy suggests that the [CuCl4](2-) ions in the Cu-based ILs have a distorted tetrahedral geometry.},
  language  = {en}
}
@article{AbouserieZehbeMetzneretal.2017,
  author    = {Abouserie, Ahed and Zehbe, Kerstin and Metzner, Philipp and Kelling, Alexandra and G{\"u}nter, Christina and Schilde, Uwe and Strauch, Peter and K{\"o}rzd{\"o}rfer, Thomas and Taubert, Andreas},
  title     = {Alkylpyridinium Tetrahalidometallate Ionic Liquids and Ionic Liquid Crystals: Insights into the Origin of Their Phase Behavior},
  series = {European journal of inorganic chemistry : a journal of ChemPubSoc Europe},
  journal   = {European journal of inorganic chemistry : a journal of ChemPubSoc Europe},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1434-1948},
  doi       = {10.1002/ejic.201700826},
  pages     = {5640 -- 5649},
  year      = {2017},
  abstract  = {Six N-alkylpyridinium salts [CnPy](2)[MCl4] (n = 4 or 12 and M = Co, Cu, Zn) were synthesized, and their structure and thermal properties were studied. The [C4Py](2)[MCl4] compounds are monoclinic and crystallize in the space group P2(1)/n. The crystals of the longer chain analogues [C12Py](2)[MCl4] are triclinic and crystallize in the space group P (1) over bar. Above the melting temperature, all compounds are ionic liquids (ILs). The derivatives with the longer C12 chain exhibit liquid crystallinity and the shorter chain compounds only show a melting transition. Consistent with single-crystal analysis, electron paramagnetic resonance spectroscopy suggests that the [CuCl4](2-) ions in the Cu-based ILs have a distorted tetrahedral geometry.},
  language  = {en}
}
@article{AyiKhareStrauchetal.2010,
  author    = {Ayi, Ayi A. and Khare, Varsha and Strauch, Peter and Girard, J{\`e}r{\^o}me and Fromm, Katharina M. and Taubert, Andreas},
  title     = {On the chemical synthesis of titanium nanoparticles from ionic liquids},
  issn      = {0026-9247},
  doi       = {10.1007/s00706-010-0403-4},
  year      = {2010},
  abstract  = {We report on attempts towards the synthesis of titanium nanoparticles using a wet chemical approach in imidazolium-based ionic liquids (ILs) under reducing conditions. Transmission electron microscopy finds nanoparticles in all cases. UV/Vis spectroscopy confirms the nanoparticulate nature of the precipitate, as in all cases an absorption band between ca. 280 and 300 nm is visible. IR spectroscopy shows that even after extensive washing and drying, some IL remains adsorbed on the nanoparticles. Raman spectroscopy suggests the formation of anatase nanoparticles, but X-ray diffraction reveals that, possibly, amorphous titania forms or that the nanoparticles are so small that a clear structure assignment is not possible. The report thus shows that (possibly amorphous) titanium oxides even form under reducing conditions and that the chemical synthesis of titanium nanoparticles in ILs remains elusive.},
  language  = {en}
}
@article{BagdahnTaubert2013,
  author    = {Bagdahn, Christian and Taubert, Andreas},
  title     = {Ionogel fiber mats - functional materials via electrospinning of PMMA and the ionic liquid bis(1-butyl-3-methyl-imidazolium) Tetrachloridocuprate(II), [Bmim](2)[CuCl4]},
  series = {Zeitschrift f{\"u}r Naturforschung : B, Chemical sciences},
  volume    = {68},
  journal   = {Zeitschrift f{\"u}r Naturforschung : B, Chemical sciences},
  number    = {10},
  publisher = {De Gruyter},
  address   = {T{\"u}bingen},
  issn      = {0932-0776},
  doi       = {10.5560/ZNB.2013-3195},
  pages     = {1163 -- 1171},
  year      = {2013},
  abstract  = {Ionogel fiber mats were made by electrospinning poly(methylmethacrylate) (PMMA) and the ionic liquid (IL) bis(1-butyl-3-methyl-imidazolium) tetrachloridocupraten, [Bmim](2)[CuCl4], from acetone. The morphology of the electrospun ionogels strongly depends on the spinning parameters. Dense and uniform fiber mats were only obtained at concentrations of 60 to 70 g of polymer and IL mass combined. Lower concentrations led to a low number of poorly defined fibers. High voltages of 20 to 25 kV led to well-defined and uniform fibers; voltages between 15 and 20 kV again led to less uniform and less dense fibers. At 10 kV and lower, no spinning could be induced. Finally, PMMA fibers electrospun without IL show a less well-defined morphology combining fibers and oblong droplets indicating that the IL has a beneficial effect on the electrospinning process. The resulting materials are prototypes for new functional materials, for example in sterile filtration.},
  language  = {en}
}
@article{BalischewskiBehrensZehbeetal.2020,
  author    = {Balischewski, Christian and Behrens, Karsten and Zehbe, Kerstin and G{\"u}nter, Christina and Mies, Stefan and Sperlich, Eric and Kelling, Alexandra and Taubert, Andreas},
  title     = {Ionic liquids with more than one metal},
  series = {Chemistry - a European journal},
  volume    = {26},
  journal   = {Chemistry - a European journal},
  number    = {72},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0947-6539},
  doi       = {10.1002/chem.202003097},
  pages     = {17504 -- 17513},
  year      = {2020},
  abstract  = {Thirteen N-butylpyridinium salts, including three monometallic [C4Py](2)[MCl4], nine bimetallic [C4Py](2)[(M1-xMxCl4)-M-a-Cl-b] and one trimetallic compound [C4Py](2)[(M1-y-zMyMz (c) Cl4)-M-a-M-b] (M=Co, Cu, Mn; x=0.25, 0.50 or 0.75 and y=z=0.33), were synthesized and their structure and thermal and electrochemical properties were studied. All compounds are ionic liquids (ILs) with melting points between 69 and 93 degrees C. X-ray diffraction proves that all ILs are isostructural. The conductivity at room temperature is between 10(-4) and 10(-8) S cm(-1). Some Cu-based ILs reach conductivities of 10(-2) S cm(-1), which is, however, probably due to IL dec. This correlates with the optical bandgap measurements indicating the formation of large bandgap semiconductors. At elevated temperatures approaching the melting points, the conductivities reach up to 1.47x10(-1) S cm(-1) at 70 degrees C. The electrochemical stability windows of the ILs are between 2.5 and 3.0 V.},
  language  = {en}
}
@article{BalischewskiBhattacharyyaSperlichetal.2022,
  author    = {Balischewski, Christian and Bhattacharyya, Biswajit and Sperlich, Eric and G{\"u}nter, Christina and Beqiraj, Alkit and Klamroth, Tillmann and Behrens, Karsten and Mies, Stefan and Kelling, Alexandra and Lubahn, Susanne and Holtzheimer, Lea and Nitschke, Anne and Taubert, Andreas},
  title     = {Tetrahalidometallate(II) ionic liquids with more than one metal},
  series = {Chemistry - a European journal},
  volume    = {28},
  journal   = {Chemistry - a European journal},
  number    = {64},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-3765},
  doi       = {10.1002/chem.202201068},
  pages     = {13},
  year      = {2022},
  abstract  = {Fifteen N-butylpyridinium salts - five monometallic [C4Py](2)[MBr4] and ten bimetallic [C4Py](2)[(M0.5M0.5Br4)-M-a-Br-b] (M=Co, Cu, Mn, Ni, Zn) - were synthesized, and their structures and thermal and electrochemical properties were studied. All the compounds are ionic liquids (ILs) with melting points between 64 and 101 degrees C. Powder and single-crystal X-ray diffraction show that all ILs are isostructural. The electrochemical stability windows of the ILs are between 2 and 3 V. The conductivities at room temperature are between 10(-5) and 10(-6) S cm(-1). At elevated temperatures, the conductivities reach up to 10(-4) S cm(-1) at 70 degrees C. The structures and properties of the current bromide-based ILs were also compared with those of previous examples using chloride ligands, which illustrated differences and similarities between the two groups of ILs.},
  language  = {en}
}
@article{BalischewskiChoiBehrensetal.2021,
  author    = {Balischewski, Christian and Choi, Hyung-Seok and Behrens, Karsten and Beqiraj, Alkit and K{\"o}rzd{\"o}rfer, Thomas and Gessner, Andre and Wedel, Armin and Taubert, Andreas},
  title     = {Metal sulfide nanoparticle synthesis with ionic liquids state of the art and future perspectives},
  series = {ChemistryOpen},
  volume    = {10},
  journal   = {ChemistryOpen},
  number    = {2},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {2191-1363},
  doi       = {10.1002/open.202000357},
  pages     = {272 -- 295},
  year      = {2021},
  abstract  = {Metal sulfides are among the most promising materials for a wide variety of technologically relevant applications ranging from energy to environment and beyond. Incidentally, ionic liquids (ILs) have been among the top research subjects for the same applications and also for inorganic materials synthesis. As a result, the exploitation of the peculiar properties of ILs for metal sulfide synthesis could provide attractive new avenues for the generation of new, highly specific metal sulfides for numerous applications. This article therefore describes current developments in metal sulfide nano-particle synthesis as exemplified by a number of highlight examples. Moreover, the article demonstrates how ILs have been used in metal sulfide synthesis and discusses the benefits of using ILs over more traditional approaches. Finally, the article demonstrates some technological challenges and how ILs could be used to further advance the production and specific property engineering of metal sulfide nanomaterials, again based on a number of selected examples.},
  language  = {en}
}
@article{BehrensBalischewskiSperlichetal.2022,
  author    = {Behrens, Karsten and Balischewski, Christian and Sperlich, Eric and Menski, Antonia Isabell and Balderas-Valadez, Ruth Fabiola and Pacholski, Claudia and G{\"u}nter, Christina and Lubahn, Susanne and Kelling, Alexandra and Taubert, Andreas},
  title     = {Mixed chloridometallate(ii) ionic liquids with tunable color and optical response for potential ammonia sensors},
  series = {RSC Advances},
  volume    = {12},
  journal   = {RSC Advances},
  publisher = {RSC},
  address   = {London},
  issn      = {2046-2069},
  doi       = {10.1039/d2ra05581c},
  pages     = {35072 -- 35082},
  year      = {2022},
  abstract  = {Eight d-metal-containing N-butylpyridinium ionic liquids (ILs) with the nominal composition (C4Py)2[Ni0.5M0.5Cl4] or (C4Py)2[Zn0.5M0.5Cl4] (M = Cu, Co, Mn, Ni, Zn; C4Py = N-butylpyridinium) were synthesized, characterized, and investigated for their optical properties. Single crystal and powder X-ray analysis shows that the compounds are isostructural to existing examples based on other d-metal ions. Inductively coupled plasma optical emission spectroscopy measurements confirm that the metal/metal ratio is around 50 : 50. UV-Vis spectroscopy shows that the optical absorption can be tuned by selection of the constituent metals. Moreover, the compounds can act as an optical sensor for the detection of gases such as ammonia as demonstrated via a simple prototype setup.},
  language  = {en}
}
@article{BhattacharyyaBalischewskiSperlichetal.2023,
  author    = {Bhattacharyya, Biswajit and Balischewski, Christian and Sperlich, Eric and G{\"u}nter, Christina and Mies, Stefan and Kelling, Alexandra and Taubert, Andreas},
  title     = {N-Butyl Pyridinium Diiodido Argentate(I)},
  series = {Advanced materials interfaces},
  volume    = {10},
  journal   = {Advanced materials interfaces},
  number    = {12},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {2196-7350},
  doi       = {10.1002/admi.202202363},
  pages     = {7},
  year      = {2023},
  abstract  = {A new solid-state material, N-butyl pyridinium diiodido argentate(I), is synthesized using a simple and effective one-pot approach. In the solid state, the compound exhibits 1D ([AgI2](-))(n) chains that are stabilized by the N-butyl pyridinium cation. The 1D structure is further manifested by the formation of long, needle-like crystals, as revealed from electron microscopy. As the general composition is derived from metal halide-based ionic liquids, the compound has a low melting point of 100-101 degrees C, as confirmed by differential scanning calorimetry. Most importantly, the compound has a conductivity of 10(-6) S cm(-1) at room temperature. At higher temperatures the conductivity increases and reaches to 10(-4 )S cm(-1) at 70 degrees C. In contrast to AgI, however, the current material has a highly anisotropic 1D arrangement of the ionic domains. This provides direct and tuneable access to fast and anisotropic ionic conduction. The material is thus a significant step forward beyond current ion conductors and a highly promising prototype for the rational design of highly conductive ionic solid-state conductors for battery or solar cell applications.},
  language  = {en}
}
@article{BlockGuenterRodriguesetal.2021,
  author    = {Block, Inga and G{\"u}nter, Christina and Rodrigues, Alysson Duarte and Paasch, Silvia and Hesemann, Peter and Taubert, Andreas},
  title     = {Carbon Adsorbents from Spent Coffee for Removal of Methylene Blue and Methyl Orange from Water},
  series = {Materials},
  volume    = {14},
  journal   = {Materials},
  number    = {14},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma14143996},
  pages     = {18},
  year      = {2021},
  abstract  = {Activated carbons (ACs) were prepared from dried spent coffee (SCD), a biological waste product, to produce adsorbents for methylene blue (MB) and methyl orange (MO) from aqueous solution. Pre-pyrolysis activation of SCD was achieved via treatment of the SCD with aqueous sodium hydroxide solutions at 90 °C. Pyrolysis of the pretreated SCD at 500 °C for 1 h produced powders with typical characteristics of AC suitable and effective for dye adsorption. As an alternative to the rather harsh base treatment, calcium carbonate powder, a very common and abundant resource, was also studied as an activator. Mixtures of SCD and CaCO3 (1:1 w/w) yielded effective ACs for MO and MB removal upon pyrolysis needing only small amounts of AC to clear the solutions. A selectivity of the adsorption process toward anionic (MO) or cationic (MB) dyes was not observed.},
  language  = {en}
}
@article{CasseShkilnyyLindersetal.2012,
  author    = {Casse, Olivier and Shkilnyy, Andriy and Linders, J{\"u}rgen and Mayer, Christian and H{\"a}ussinger, Daniel and V{\"o}lkel, Antje and Th{\"u}nemann, Andreas F. and Dimova, Rumiana and C{\"o}lfen, Helmut and Meier, Wolfgang P. and Schlaad, Helmut and Taubert, Andreas},
  title     = {Solution behavior of double-hydrophilic block copolymers in dilute aqueous solution},
  series = {Macromolecules : a publication of the American Chemical Society},
  volume    = {45},
  journal   = {Macromolecules : a publication of the American Chemical Society},
  number    = {11},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {0024-9297},
  doi       = {10.1021/ma300621g},
  pages     = {4772 -- 4777},
  year      = {2012},
  abstract  = {The self-assembly of double-hydrophilic poly(ethylene oxide)-poly(2-methyl-2-oxazoline) diblock copolymers in water has been studied. Isothermal titration calorimetry, small-angle X-ray scattering, and analytical ultracentrifugation suggest that only single polymer chains are present in solution. In contrast, light scattering and transmission electron microscopy detect aggregates with radii of ca. 100 nm. Pulsed field gradient NMR spectroscopy confirms the presence of aggregates, although only 2\% of the polymer chains undergo aggregation. Water uptake experiments indicate differences in the hydrophilicity of the two blocks, which is believed to be the origin of the unexpected aggregation behavior (in accordance with an earlier study by Ke et al. [Macromolecules 2009, 42, 5339-5344]). The data therefore suggest that even in double-hydrophilic block copolymers, differences in hydrophilicity are sufficient to drive polymer aggregation, a phenomenon that has largely been overlooked or ignored so far.},
  language  = {en}
}
@article{DelahayeGoebelLoebbickeetal.2012,
  author    = {Delahaye, Emilie and Goebel, Ronald and Loebbicke, Ruben and Guillot, Regis and Sieber, Christoph and Taubert, Andreas},
  title     = {Silica ionogels for proton transport},
  series = {Journal of materials chemistry},
  volume    = {22},
  journal   = {Journal of materials chemistry},
  number    = {33},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {0959-9428},
  doi       = {10.1039/c2jm00037g},
  pages     = {17140 -- 17146},
  year      = {2012},
  abstract  = {A number of ionogels - silica-ionic liquid (IL) hybrid materials - were synthesized and studied for their ionic conductivity. The materials are based on a sulfonated IL, 1-methyl-3-(3-sulfopropyl-)-imidazolium p-toluenesulfonate, [PmimSO(3)H][PTS], which contains a sulfonic acid/sulfonate group both in the IL anion and in the side chain of the IL cation. By way of the sulfonate-sulfonic acid proton transfer, the IL imparts the ionogel with a high ionic conductivity of ca. 10(-2) S cm(-1) in the as-synthesized state at 120 degrees C and 10(-3) S cm(-1) in the dry state at 120 degrees C. The ionogels are stable up to ca. 150 degrees C in dynamic thermogravimetric analysis. This suggests that these materials, which are relatively cheap and easily fabricated, could find application in fuel cells in intermediate temperature ranges where many other membrane materials are not suitable.},
  language  = {en}
}
@article{DelahayeXieSchaeferetal.2011,
  author    = {Delahaye, Emilie and Xie, Zailai and Sch{\"a}fer, Andreas and Douce, Laurent and Rogez, Guillaume and Rabu, Pierre and G{\"u}nter, Christina and Gutmann, Jochen S. and Taubert, Andreas},
  title     = {Intercalation synthesis of functional hybrid materials based on layered simple hydroxide hosts and ionic liquid guests - a pathway towards multifunctional ionogels without a silica matrix?},
  series = {Dalton transactions : a journal of inorganic chemistry, including bioinorganic, organometallic, and solid-state chemistry},
  volume    = {40},
  journal   = {Dalton transactions : a journal of inorganic chemistry, including bioinorganic, organometallic, and solid-state chemistry},
  number    = {39},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1477-9226},
  doi       = {10.1039/c1dt10841g},
  pages     = {9977 -- 9988},
  year      = {2011},
  abstract  = {Functional hybrid materials on the basis of inorganic hosts and ionic liquids (ILs) as guests hold promise for a virtually unlimited number of applications. In particular, the interaction and the combination of properties of a defined inorganic matrix and a specific IL could lead to synergistic effects in property selection and tuning. Such hybrid materials, generally termed ionogels, are thus an emerging topic in hybrid materials research. The current article addresses some of the recent developments and focuses on the question why silica is currently the dominating matrix used for (inorganic) ionogel fabrication. In comparison to silica, matrix materials such as layered simple hydroxides, layered double hydroxides, clay-type substances, magnetic or catalytically active solids, and many other compounds could be much more interesting because they themselves may carry useful functionalities, which could also be exploited for multifunctional hybrid materials synthesis. The current article combines experimental results with some arguments as to how new, advanced functional hybrid materials can be generated and which obstacles will need to be overcome to successfully achieve the synthesis of a desired target material.},
  language  = {en}
}
@article{DraudeGallaPelsteretal.2013,
  author    = {Draude, F. and Galla, S. and Pelster, Axel and Tentschert, J. and Jungnickel, H. and Haase, Alfred and Mantion, Alexandre and Thuenemann, Andreas F. and Taubert, Andreas and Luch, A. and Arlinghaus, H. F.},
  title     = {ToF-SIMS and Laser-SNMS analysis of macrophages after exposure to silver nanoparticles},
  series = {Surface and interface analysis : an international journal devoted to the development and application of techniques for the analysis surfaces, interfaces and thin films},
  volume    = {45},
  journal   = {Surface and interface analysis : an international journal devoted to the development and application of techniques for the analysis surfaces, interfaces and thin films},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Hoboken},
  issn      = {0142-2421},
  doi       = {10.1002/sia.4902},
  pages     = {286 -- 289},
  year      = {2013},
  abstract  = {Silver nanoparticles (SNPs) are among the most commercialized nanoparticles because of their antibacterial effects. Besides being employed, e. g. as a coatingmaterial for sterile surfaces in household articles and appliances, the particles are also used in a broad range of medical applications. Their antibacterial properties make SNPs especially useful for wound disinfection or as a coating material for prostheses and surgical instruments. Because of their optical characteristics, the particles are of increasing interest in biodetection as well. Despite the widespread use of SNPs, there is little knowledge of their toxicity. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and laser post-ionization secondary neutral mass spectrometry (Laser-SNMS) were used to investigate the effects of SNPs on human macrophages derived from THP-1 cells in vitro. For this purpose, macrophages were exposed to SNPs. The SNP concentration ranges were chosen with regard to functional impairments of the macrophages. To optimize the analysis of the macrophages, a special silicon wafer sandwich preparation technique was employed; ToF-SIMS was employed to characterize fragments originating from macrophage cell membranes. With the use of this optimized sample preparation method, the SNP-exposed macrophages were analyzed with ToF-SIMS and with Laser-SNMS. With Laser-SNMS, the three-dimensional distribution of SNPs in cells could be readily detected with very high efficiency, sensitivity, and submicron lateral resolution. We found an accumulation of SNPs directly beneath the cell membrane in a nanoparticular state as well as agglomerations of SNPs inside the cells.},
  language  = {en}
}
@article{FarraThielWinteretal.2011,
  author    = {Farra, Ramzi and Thiel, Kerstin and Winter, Alette and Klamroth, Tillmann and Poeppl, Andreas and Kelling, Alexandra and Schilde, Uwe and Taubert, Andreas and Strauch, Peter},
  title     = {Tetrahalidocuprates(II)-structure and EPR spectroscopy Part 1: Tetrabromidocuprates(II)},
  series = {New journal of chemistry},
  volume    = {35},
  journal   = {New journal of chemistry},
  number    = {12},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1144-0546},
  doi       = {10.1039/c1nj20271e},
  pages     = {2793 -- 2803},
  year      = {2011},
  abstract  = {Tetrahalidocuprates(II) show a high degree of structural flexibility. We present the results of crystallographic and electron paramagnetic resonance (EPR) spectroscopic analyses of four new tetrabromidocuprate(II) compounds and compare the results with previously reported data. The cations in the new compounds are the sterically demanding benzyltriphenylphosphonium, methyltriphenylphosphonium, tetraphenylphosphonium, and hexadecyltrimethylammonium ions; they were used to achieve a reasonable separation of the paramagnetic Cu(II) ions for EPR spectroscopy. X-Ray crystallography shows that in all four complexes the [CuBr4](2-) units have a distorted tetrahedral coordination geometry which is in agreement with DFT calculations. The EPR hyperfine structure was not resolved. This is due to the exchange broadening resulting from still incomplete separation of the paramagnetic Cu(II) centres. Nevertheless, the principal values of the electron Zeemann tensor (g(parallel to) and g(perpendicular to)) of the complexes could be determined. A correlation of structural (X-ray) parameters with the spin density at the copper centres (DFT) is well reflected in the EPR spectra of the bromidocuprates. This enables the correlation of X-ray and EPR parameters to predict the structure of tetrabromidocuprates in physical states other than the crystalline state. As a result, we provide a method to structurally characterize [CuBr4](2-) in, for example, ionic liquids or in solution, which has important implications for e.g. catalysis or materials science.},
  language  = {en}
}
@article{FigueroaCamposGKTKruizengaSaguTchewonpietal.2022,
  author    = {Figueroa Campos, Gustavo Adolfo and G. K. T. Kruizenga, Johannes and Sagu Tchewonpi, Sorel and Schwarz, Steffen and Homann, Thomas and Taubert, Andreas and Rawel, Harshadrai Manilal},
  title     = {Effect of the post-harvest processing on protein modification in green coffee beans by phenolic compounds},
  series = {Foods : open access journal},
  volume    = {11},
  journal   = {Foods : open access journal},
  edition   = {2},
  publisher = {MDPI},
  address   = {Basel, Schweiz},
  issn      = {2304-8158},
  doi       = {10.3390/foods11020159},
  pages     = {19},
  year      = {2022},
  abstract  = {The protein fraction, important for coffee cup quality, is modified during post-harvest treatment prior to roasting. Proteins may interact with phenolic compounds, which constitute the major metabolites of coffee, where the processing affects these interactions. This allows the hypothesis that the proteins are denatured and modified via enzymatic and/or redox activation steps. The present study was initiated to encompass changes in the protein fraction. The investigations were limited to major storage protein of green coffee beans. Fourteen Coffea arabica samples from various processing methods and countries were used. Different extraction protocols were compared to maintain the status quo of the protein modification. The extracts contained about 4-8 µg of chlorogenic acid derivatives per mg of extracted protein. High-resolution chromatography with multiple reaction monitoring was used to detect lysine modifications in the coffee protein. Marker peptides were allocated for the storage protein of the coffee beans. Among these, the modified peptides K.FFLANGPQQGGK.E and R.LGGK.T of the α-chain and R.ITTVNSQK.I and K.VFDDEVK.Q of β-chain were detected. Results showed a significant increase (p < 0.05) of modified peptides from wet processed green beans as compared to the dry ones. The present study contributes to a better understanding of the influence of the different processing methods on protein quality and its role in the scope of coffee cup quality and aroma. View Full-Text},
  language  = {en}
}
@article{FigueroaCamposPerezBlocketal.2021,
  author    = {Figueroa Campos, Gustavo Adolfo and Perez, Jeffrey Paulo H. and Block, Inga and Sagu Tchewonpi, Sorel and Saravia Celis, Pedro and Taubert, Andreas and Rawel, Harshadrai Manilal},
  title     = {Preparation of activated carbons from spent coffee and coffee parchment and assessment of their adsorbent efficiency},
  series = {Processes : open access journal},
  volume    = {9},
  journal   = {Processes : open access journal},
  number    = {8},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2227-9717},
  doi       = {10.3390/pr9081396},
  pages     = {18},
  year      = {2021},
  abstract  = {The valorization of coffee wastes through modification to activated carbon has been considered as a low-cost adsorbent with prospective to compete with commercial carbons. So far, very few studies have referred to the valorization of coffee parchment into activated carbon. Moreover, low-cost and efficient activation methods need to be more investigated. The aim of this work was to prepare activated carbon from spent coffee grounds and parchment, and to assess their adsorption performance. The co-calcination processing with calcium carbonate was used to prepare the activated carbons, and their adsorption capacity for organic acids, phenolic compounds and proteins was evaluated. Both spent coffee grounds and parchment showed yields after the calcination and washing treatments of around 9.0\%. The adsorption of lactic acid was found to be optimal at pH 2. The maximum adsorption capacity of lactic acid with standard commercial granular activated carbon was 73.78 mg/g, while the values of 32.33 and 14.73 mg/g were registered for the parchment and spent coffee grounds activated carbons, respectively. The Langmuir isotherm showed that lactic acid was adsorbed as a monolayer and distributed homogeneously on the surface. Around 50\% of total phenols and protein content from coffee wastewater were adsorbed after treatment with the prepared activated carbons, while 44, 43, and up to 84\% of hydrophobic compounds were removed using parchment, spent coffee grounds and commercial activated carbon, respectively; the adsorption efficiencies of hydrophilic compounds ranged between 13 and 48\%. Finally, these results illustrate the potential valorization of coffee by-products parchment and spent coffee grounds into activated carbon and their use as low-cost adsorbent for the removal of organic compounds from aqueous solutions.},
  language  = {en}
}
@article{GoebelHesemannFriedrichetal.2014,
  author    = {Goebel, Ronald and Hesemann, Peter and Friedrich, Alwin and Rothe, Regina and Schlaad, Helmut and Taubert, Andreas},
  title     = {Modular thiol-ene chemistry approach towards mesoporous silica monoliths with organically modified pore walls},
  series = {Chemistry - a European journal},
  volume    = {20},
  journal   = {Chemistry - a European journal},
  number    = {52},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0947-6539},
  doi       = {10.1002/chem.201403982},
  pages     = {17579 -- 17589},
  year      = {2014},
  abstract  = {The surface modification of mesoporous silica monoliths through thiol-ene chemistry is reported. First, mesoporous silica monoliths with vinyl, allyl, and thiol groups were synthesized through a sol-gel hydrolysis-poly-condensation reaction from tetramethyl orthosilicate (TMOS) and vinyltriethoxysilane, allyltriethoxysilane, and (3-mercaptopropyl) trimethoxysilane, respectively. By variation of the molar ratio of the comonomers TMOS and functional silane, mesoporous silica objects containing different amounts of vinyl, allyl, and thiol groups were obtained. These intermediates can subsequently be derivatized through radical photoaddition reactions either with a thiol or an olefin, depending on the initial pore wall functionality, to yield silica monoliths with different pore-wall chemistries. Nitrogen sorption, small-angle X-ray scattering, solid-state NMR spectroscopy, elemental analysis, thermogravimetric analysis, and redox titration demonstrate that the synthetic pathway influences the morphology and pore characteristics of the resulting monoliths and also plays a significant role in the efficiency of functionalization. Moreover, the different reactivity of the vinyl and allyl groups on the pore wall affects the addition reaction, and hence, the degree of the pore-wall functionalization. This report demonstrates that thiol-ene photoaddition reactions are a versatile platform for the generation of a large variety of organically modified silica monoliths with different pore surfaces.},
  language  = {en}
}
@article{GoebelHesemannWeberetal.2009,
  author    = {Goebel, Ronald and Hesemann, Peter and Weber, Jens and Moeller, El{\´e}onore and Friedrich, Alwin and Beuermann, Sabine and Taubert, Andreas},
  title     = {Surprisingly high, bulk liquid-like mobility of silica-confined ionic liquids},
  issn      = {1463-9076},
  doi       = {10.1039/B821833a},
  year      = {2009},
  abstract  = {Mesoporous silica monoliths were prepared by the sol - gel technique and. lled with 1-ethyl-3-methyl imidazolium [Emim]-X (X = dicyanamide [N(CN)(2)], ethyl sulfate [EtSO4], thiocyanate [SCN], and triflate [TfO]) ionic liquids (ILs) using a methanol-IL exchange technique. The structure and behavior of the ILs inside the silica monoliths were studied using X-ray scattering, nitrogen sorption, IR spectroscopy, solid-state NMR, and thermal analysis. DSC finds shifts in both the glass transition temperature and melting points (where applicable) of the ILs. Glass transition and melting occur well below room temperature. There is thus no conflict with the NMR and IR data, which show that the ILs are as mobile at room temperature as the bulk (not confined) ILs. The very narrow line widths of the NMR spectra suggest that the ILs in our materials have the highest mobility reported for confined ILs so far. As a result, our data suggest that it is possible to generate IL/silica hybrid materials (ionogels) with bulk-like properties of the IL. This could be interesting for applications in, e.g., the solar cell or membrane fields.},
  language  = {en}
}