@phdthesis{Aich2015,
  author    = {Aich, Valentin},
  title     = {Floods in the Niger River Basin in the face of global change},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-91577},
  school      = {Universit{\"a}t Potsdam},
  pages     = {xxi, 275},
  year      = {2015},
  abstract  = {In the last decade, the number and dimensions of catastrophic flooding events in the Niger River Basin (NRB) have markedly increased. Despite the devastating impact of the floods on the population and the mainly agriculturally based economy of the riverine nations, awareness of the hazards in policy and science is still low. The urgency of this topic and the existing research deficits are the motivation for the present dissertation. The thesis is an initial detailed assessment of the increasing flood risk in the NRB. The research strategy is based on four questions regarding (1) features of the change in flood risk, (2) reasons for the change in the flood regime, (3) expected changes of the flood regime given climate and land use changes, and (4) recommendations from previous analysis for reducing the flood risk in the NRB. The question examining the features of change in the flood regime is answered by means of statistical analysis. Trend, correlation, changepoint, and variance analyses show that, in addition to the factors exposure and vulnerability, the hazard itself has also increased significantly in the NRB, in accordance with the decadal climate pattern of West Africa. The northern arid and semi-arid parts of the NRB are those most affected by the changes. As potential reasons for the increase in flood magnitudes, climate and land use changes are attributed by means of a hypothesis-testing framework. Two different approaches, based on either data analysis or simulation, lead to similar results, showing that the influence of climatic changes is generally larger compared to that of land use changes. Only in the dry areas of the NRB is the influence of land use changes comparable to that of climatic alterations. Future changes of the flood regime are evaluated using modelling results. First ensembles of statistically and dynamically downscaled climate models based on different emission scenarios are analyzed. The models agree with a distinct increase in temperature. The precipitation signal, however, is not coherent. The climate scenarios are used to drive an eco-hydrological model. The influence of climatic changes on the flood regime is uncertain due to the unclear precipitation signal. Still, in general, higher flood peaks are expected. In a next step, effects of land use changes are integrated into the model. Different scenarios show that regreening might help to reduce flood peaks. In contrast, an expansion of agriculture might enhance the flood peaks in the NRB. Similarly to the analysis of observed changes in the flood regime, the impacts of climate- and land use changes for the future scenarios are also most severe in the dry areas of the NRB. In order to answer the final research question, the results of the above analysis are integrated into a range of recommendations for science and policy on how to reduce flood risk in the NRB. The main recommendations include a stronger consideration of the enormous natural climate variability in the NRB and a focus on so called "no-regret" adaptation strategies which account for high uncertainty, as well as a stronger consideration of regional differences. Regarding the prevention and mitigation of catastrophic flooding, the most vulnerable and sensitive areas in the basin, the arid and semi-arid Sahelian and Sudano-Sahelian regions, should be prioritized. Eventually, an active, science-based and science-guided flood policy is recommended. The enormous population growth in the NRB in connection with the expected deterioration of environmental and climatic conditions is likely to enhance the region´s vulnerability to flooding. A smart and sustainable flood policy can help mitigate these negative impacts of flooding on the development of riverine societies in West Africa.},
  language  = {en}
}
@phdthesis{Brosinsky2015,
  author    = {Brosinsky, Arlena},
  title     = {Spectral fingerprinting},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-83369},
  school      = {Universit{\"a}t Potsdam},
  pages     = {VI, 117},
  year      = {2015},
  abstract  = {Current research on runoff and erosion processes, as well as an increasing demand for sustainable watershed management emphasize the need for an improved understanding of sediment dynamics. This involves the accurate assessment of erosion rates and sediment transfer, yield and origin. A variety of methods exist to capture these processes at the catchment scale. Among these, sediment fingerprinting, a technique to trace back the origin of sediment, has attracted increasing attention by the scientific community in recent years. It is a two-step procedure, based on the fundamental assumptions that potential sources of sediment can be reliably discriminated based on a set of characteristic 'fingerprint' properties, and that a comparison of source and sediment fingerprints allows to quantify the relative contribution of each source. This thesis aims at further assessing the potential of spectroscopy to assist and improve the sediment fingerprinting technique. Specifically, this work focuses on (1) whether potential sediment sources can be reliably identified based on spectral features ('fingerprints'), whether (2) these spectral fingerprints permit the quantification of relative source contribution, and whether (3) in situ derived source information is sufficient for this purpose. Furthermore, sediment fingerprinting using spectral information is applied in a study catchment to (4) identify major sources and observe how relative source contributions change between and within individual flood events. And finally, (5) spectral fingerprinting results are compared and combined with simultaneous sediment flux measurements to study sediment origin, transport and storage behaviour. For the sediment fingerprinting approach, soil samples were collected from potential sediment sources within the Is{\´a}bena catchment, a meso-scale basin in the central Spanish Pyrenees. Undisturbed samples of the upper soil layer were measured in situ using an ASD spectroradiometer and subsequently sampled for measurements in the laboratory. Suspended sediment was sampled automatically by means of ISCO samplers at the catchment as well as at the five major subcatchment outlets during flood events, and stored fine sediment from the channel bed was collected from 14 cross-sections along the main river. Artificial mixtures of known contributions were produced from source soil samples. Then, all source, sediment and mixture samples were dried and spectrally measured in the laboratory. Subsequently, colour coefficients and physically based features with relation to organic carbon, iron oxide, clay content and carbonate, were calculated from all in situ and laboratory spectra. Spectral parameters passing a number of prerequisite tests were submitted to principal component analyses to study natural clustering of samples, discriminant function analyses to observe source differentiation accuracy, and a mixing model for source contribution assessment. In addition, annual as well as flood event based suspended sediment fluxes from the catchment and its subcatchments were calculated from rainfall, water discharge and suspended sediment concentration measurements using rating curves and Quantile Regression Forests. Results of sediment flux monitoring were interpreted individually with respect to storage behaviour, compared to fingerprinting source ascriptions and combined with fingerprinting to assess their joint explanatory potential. In response to the key questions of this work, (1) three source types (land use) and five spatial sources (subcatchments) could be reliably discriminated based on spectral fingerprints. The artificial mixture experiment revealed that while (2) laboratory parameters permitted source contribution assessment, (3) the use of in situ derived information was insufficient. Apparently, high discrimination accuracy does not necessarily imply good quantification results. When applied to suspended sediment samples of the catchment outlet, the spectral fingerprinting approach was able to (4) quantify the major sediment sources: badlands and the Villacarli subcatchment, respectively, were identified as main contributors, which is consistent with field observations and previous studies. Thereby, source contribution was found to vary both, within and between individual flood events. Also sediment flux was found to vary considerably, annually as well as seasonally and on flood event base. Storage was confirmed to play an important role in the sediment dynamics of the studied catchment, whereas floods with lower total sediment yield tend to deposit and floods with higher yield rather remove material from the channel bed. Finally, a comparison of flux measurements with fingerprinting results highlighted the fact that (5) immediate transport from sources to the catchment outlet cannot be assumed. A combination of the two methods revealed different aspects of sediment dynamics that none of the techniques could have uncovered individually. In summary, spectral properties provide a fast, non-destructive, and cost-efficient means to discriminate and quantify sediment sources, whereas, unfortunately, straight-forward in situ collected source information is insufficient for the approach. Mixture modelling using artificial mixtures permits valuable insights into the capabilities and limitations of the method and similar experiments are strongly recommended to be performed in the future. Furthermore, a combination of techniques such as e.g. (spectral) sediment fingerprinting and sediment flux monitoring can provide comprehensive understanding of sediment dynamics.},
  language  = {en}
}
@phdthesis{Schrameier2015,
  author    = {Schrameier, Matthias},
  title     = {Zielsteuerung im {\"o}ffentlichen Sektor und deren Integration in die Managementroutinen},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-79659},
  school      = {Universit{\"a}t Potsdam},
  pages     = {206},
  year      = {2015},
  abstract  = {Die Arbeit geht der Frage nach, wie Innovationen in einer Organisation des {\"o}ffentlichen Sektors aufgenommen wurden und zu welchen Ver{\"a}nderungen dies f{\"u}hrte. Im Vordergrund steht hier nicht die Innovation selbst, sondern vielmehr die Anpassungsmechanismen in der Organisation. Folgende Forschungsfragen wurden dazu gew{\"a}hlt: 1. Wie wurde das Instrument Zielsteuerung bzw. Zielvereinbarung im {\"o}ffentlichen Sektor eingef{\"u}hrt und in die Managementroutinen integriert? 2. Welche Faktoren f{\"u}hren zu einer Integration der Zielsteuerung in die Managementroutinen? 3. Welche Empfehlungen f{\"u}r die Praxis lassen sich daraus ableiten? Dazu wurde ein Landesbetrieb in Brandenburg detailliert untersucht und 31 Interviews mit F{\"u}hrungskr{\"a}ften der zweiten und dritten Managementebene gef{\"u}hrt. In dieser Organisation wurde im Rahmen der deutschlandweiten Reformbewegung in der {\"o}ffentlichen Verwaltung das Instrument Zielsteuerung bzw. Zielvereinbarung eingef{\"u}hrt und mit ganz konkreten Erwartungen verbunden. Als Untersuchungseinheit der m{\"o}glichen Anpassungen und Ver{\"a}nderungen wurde das Konstrukt der Managementroutinen herangezogen, welche als kollektive Handlungsmuster ganz bewusst individuelle Verhaltensweisen ausklammerten. Die Arbeit konnte eine Reihe von fr{\"u}heren Erkenntnissen best{\"a}tigen und zudem nachweisen, dass, entgegen des h{\"a}ufigen Vorurteils, Innovationen aus dem privatwirtschaftlichem Raum doch auch zu positiven Ver{\"a}nderungen in Organisationen der {\"o}ffentlichen Hand f{\"u}hren k{\"o}nnen. Es kam hier jedoch nicht zur Entwicklung neuer, sondern zu einer Anpassung der bestehenden Routinen. Auf dieser Basis konnte festgestellt werden, dass ein stufenweiser Einf{\"u}hrungsvorgang zun{\"a}chst auf der Ebene der ver{\"a}nderten Zielvorstellungen der F{\"u}hrungskr{\"a}fte zum Erfolg f{\"u}hrte. Erst nach der Anpassung auf dieser „ostentativen" Ebene kam es mit etwas Verz{\"o}gerung zu einer Ver{\"a}nderung auf der Ebene der konkreten Handlungen. Im Hinblick auf die Einflussfaktoren der Innovation konnte festgestellt werden, dass viele Aspekte der Zielsetzungstheorie nach wie vor relevant sind und instabile politische Rahmenbedingungen zu wesentlichen Einschr{\"a}nkungen der Entfaltungsm{\"o}glichkeiten der Innovation f{\"u}hren k{\"o}nnen. F{\"u}r viele Einflussfaktoren konnten allerdings sowohl positive als auch negative Wirkungen identifiziert werden.},
  language  = {de}
}
@phdthesis{Kniepert2015,
  author    = {Kniepert, Juliane},
  title     = {Correlation between dynamic parameters and device performance of organic solar cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-90087},
  school      = {Universit{\"a}t Potsdam},
  pages     = {129},
  year      = {2015},
  abstract  = {Organic bulk heterojunction (BHJ) solar cells based on polymer:fullerene blends are a promising alternative for a low-cost solar energy conversion. Despite significant improvements of the power conversion efficiency in recent years, the fundamental working principles of these devices are yet not fully understood. In general, the current output of organic solar cells is determined by the generation of free charge carriers upon light absorption and their transport to the electrodes in competition to the loss of charge carriers due to recombination. The object of this thesis is to provide a comprehensive understanding of the dynamic processes and physical parameters determining the performance. A new approach for analyzing the characteristic current-voltage output was developed comprising the experimental determination of the efficiencies of charge carrier generation, recombination and transport, combined with numerical device simulations. Central issues at the beginning of this work were the influence of an electric field on the free carrier generation process and the contribution of generation, recombination and transport to the current-voltage characteristics. An elegant way to directly measure the field dependence of the free carrier generation is the Time Delayed Collection Field (TDCF) method. In TDCF charge carriers are generated by a short laser pulse and subsequently extracted by a defined rectangular voltage pulse. A new setup was established with an improved time resolution compared to former reports in literature. It was found that charge generation is in general independent of the electric field, in contrast to the current view in literature and opposed to the expectations of the Braun-Onsager model that was commonly used to describe the charge generation process. Even in cases where the charge generation was found to be field-dependend, numerical modelling showed that this field-dependence is in general not capable to account for the voltage dependence of the photocurrent. This highlights the importance of efficient charge extraction in competition to non-geminate recombination, which is the second objective of the thesis. Therefore, two different techniques were combined to characterize the dynamics and efficiency of non-geminate recombination under device-relevant conditions. One new approach is to perform TDCF measurements with increasing delay between generation and extraction of charges. Thus, TDCF was used for the first time to measure charge carrier generation, recombination and transport with the same experimental setup. This excludes experimental errors due to different measurement and preparation conditions and demonstrates the strength of this technique. An analytic model for the description of TDCF transients was developed and revealed the experimental conditions for which reliable results can be obtained. In particular, it turned out that the \$RC\$ time of the setup which is mainly given by the sample geometry has a significant influence on the shape of the transients which has to be considered for correct data analysis. Secondly, a complementary method was applied to characterize charge carrier recombination under steady state bias and illumination, i.e. under realistic operating conditions. This approach relies on the precise determination of the steady state carrier densities established in the active layer. It turned out that current techniques were not sufficient to measure carrier densities with the necessary accuracy. Therefore, a new technique {Bias Assisted Charge Extraction} (BACE) was developed. Here, the charge carriers photogenerated under steady state illumination are extracted by applying a high reverse bias. The accelerated extraction compared to conventional charge extraction minimizes losses through non-geminate recombination and trapping during extraction. By performing numerical device simulations under steady state, conditions were established under which quantitative information on the dynamics can be retrieved from BACE measurements. The applied experimental techniques allowed to sensitively analyse and quantify geminate and non-geminate recombination losses along with charge transport in organic solar cells. A full analysis was exemplarily demonstrated for two prominent polymer-fullerene blends. The model system P3HT:PCBM spincast from chloroform (as prepared) exhibits poor power conversion efficiencies (PCE) on the order of 0.5\%, mainly caused by low fill factors (FF) and currents. It could be shown that the performance of these devices is limited by the hole transport and large bimolecular recombination (BMR) losses, while geminate recombination losses are insignificant. The low polymer crystallinity and poor interconnection between the polymer and fullerene domains leads to a hole mobility of the order of 10^-7 cm^2/Vs which is several orders of magnitude lower than the electron mobility in these devices. The concomitant build up of space charge hinders extraction of both electrons and holes and promotes bimolecular recombination losses. Thermal annealing of P3HT:PCBM blends directly after spin coating improves crystallinity and interconnection of the polymer and the fullerene phase and results in comparatively high electron and hole mobilities in the order of 10^-3 cm^2/Vs and 10^-4 cm^2/Vs, respectively. In addition, a coarsening of the domain sizes leads to a reduction of the BMR by one order of magnitude. High charge carrier mobilities and low recombination losses result in comparatively high FF (>65\%) and short circuit current (J_SC ≈ 10 mA/cm^2). The overall device performance (PCE ≈ 4\%) is only limited by a rather low spectral overlap of absorption and solar emission and a small V_OC, given by the energetics of the P3HT. From this point of view the combination of the low bandgap polymer PTB7 with PCBM is a promising approach. In BHJ solar cells, this polymer leads to a higher V_OC due to optimized energetics with PCBM. However, the J_SC in these (unoptimized) devices is similar to the J_SC in the optimized blend with P3HT and the FF is rather low (≈ 50\%). It turned out that the unoptimized PTB7:PCBM blends suffer from high BMR, a low electron mobility of the order of 10^-5 cm^2/Vs and geminate recombination losses due to field dependent charge carrier generation. The use of the solvent additive DIO optimizes the blend morphology, mainly by suppressing the formation of very large fullerene domains and by forming a more uniform structure of well interconnected donor and acceptor domains of the order of a few nanometers. Our analysis shows that this results in an increase of the electron mobility by about one order of magnitude (3 x 10^-4 cm^2/Vs), while BMR and geminate recombination losses are significantly reduced. In total these effects improve the J_SC (≈ 17 mA/cm^2) and the FF (> 70\%). In 2012 this polymer/fullerene combination resulted in a record PCE for a single junction OSC of 9.2\%. Remarkably, the numerical device simulations revealed that the specific shape of the J-V characteristics depends very sensitively to the variation of not only one, but all dynamic parameters. On the one hand this proves that the experimentally determined parameters, if leading to a good match between simulated and measured J-V curves, are realistic and reliable. On the other hand it also emphasizes the importance to consider all involved dynamic quantities, namely charge carrier generation, geminate and non-geminate recombination as well as electron and hole mobilities. The measurement or investigation of only a subset of these parameters as frequently found in literature will lead to an incomplete picture and possibly to misleading conclusions. Importantly, the comparison of the numerical device simulation employing the measured parameters and the experimental \$J-V\$ characteristics allows to identify loss channels and limitations of OSC. For example, it turned out that inefficient extraction of charge carriers is a criticical limitation factor that is often disobeyed. However, efficient and fast transport of charges becomes more and more important with the development of new low bandgap materials with very high internal quantum efficiencies. Likewise, due to moderate charge carrier mobilities, the active layer thicknesses of current high-performance devices are usually limited to around 100 nm. However, larger layer thicknesses would be more favourable with respect to higher current output and robustness of production. Newly designed donor materials should therefore at best show a high tendency to form crystalline structures, as observed in P3HT, combined with the optimized energetics and quantum efficiency of, for example, PTB7.},
  language  = {en}
}
@phdthesis{Ramelli2015,
  author    = {Ramelli, Christian},
  title     = {Die Rheinische Verlaufsform im rheinfr{\"a}nkischen Dialekt},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-102797},
  school      = {Universit{\"a}t Potsdam},
  pages     = {x, 260},
  year      = {2015},
  abstract  = {Diese Arbeit befasst sich mit der Rheinischen Verlaufsform (RV) im rheinfr{\"a}nkischen Dialekt. Nach dem DUDEN handelt es sich bei der RV um eine Konstruktion, die aus dem Kopulaverb sein und einer PP mit am und nominalisiertem Infinitiv besteht und dem Ausdruck von progressivem Aspekt dient. Die vorliegenden Arbeiten zur RV besch{\"a}ftigen sich im Wesentlichen entweder mit der Auspr{\"a}gung der Konstruktion im Standarddeutschen (z.B. Reimann (1999), Krause (2002), R{\"o}del (2003), R{\"o}del (2004a), R{\"o}del (2004b), van Pottelberge (2004)) oder im Ripuarischen (z.B. Andersson (1989), Bhatt \& Schmidt (1993)) und kommen zu unterschiedlichen Ergebnissen bez{\"u}glich der Verwendungsm{\"o}glichkeiten und des Aufbaus der Konstruktion, insbesondere des Status des Infinitivs in der Verlaufsform. Hauptziel dieser Arbeit ist es, zu zeigen, dass sich die Grammatikalisierung der Verlaufsform von der im DUDEN beschriebenen Konstruktion zu einer analytischen Verbform entlang eines festen Grammatikalisierungspfades vollzieht und die entsprechenden Teilschritte bei der Entwicklung zu einer analytischen Verbform herauszuarbeiten. Auf dieser Grundlage wird in der Arbeit dargestellt, wie sich mittels eines geeigneten Sets an Indikatoren der Grammatikalisierungsgrad der Verlaufsform in einem Dialektraum oder einem diatopischen Register konkret feststellen l{\"a}sst.},
  language  = {de}
}
@phdthesis{Mitzscherling2015,
  author    = {Mitzscherling, Steffen},
  title     = {Polyelectrolyte multilayers for plasmonics and picosecond ultrasonics},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-80833},
  school      = {Universit{\"a}t Potsdam},
  pages     = {93},
  year      = {2015},
  abstract  = {This thesis investigates the application of polyelectrolyte multilayers in plasmonics and picosecond acoustics. The observed samples were fabricated by the spin-assisted layer-by-layer deposition technique that allowed a precise tuning of layer thickness in the range of few nanometers. The first field of interest deals with the interaction of light-induced localized surface plasmons (LSP) of rod-shaped gold nanoparticles with the particles' environment. The environment consists of an air phase and a phase of polyelectrolytes, whose ratio affects the spectral position of the LSP resonance. Measured UV-VIS spectra showed the shift of the LSP absorption peak as a function of the cover layer thickness of the particles. The data are modeled using an average dielectric function instead of the dielectric functions of air and polyelectrolytes. In addition using a measured dielectric function of the gold nanoparticles, the position of the LSP absorption peak could be simulated with good agreement to the data. The analytic model helps to understand the optical properties of metal nanoparticles in an inhomogeneous environment. The second part of this work discusses the applicability of PAzo/PAH and dye-doped PSS/PAH polyelectrolyte multilayers as transducers to generate hypersound pulses. The generated strain pulses were detected by time-domain Brillouin scattering (TDBS) using a pump-probe laser setup. Transducer layers made of polyelectrolytes were compared qualitatively to common aluminum transducers in terms of measured TDBS signal amplitude, degradation due to laser excitation, and sample preparation. The measurements proved that fast and easy prepared polyelectrolyte transducers provided stronger TDBS signals than the aluminum transducer. AFM topography measurements showed a degradation of the polyelectrolyte structures, especially for the PAzo/PAH sample. To quantify the induced strain, optical barriers were introduced to separate the transducer material from the medium of the hypersound propagation. Difficulties in the sample preparation prohibited a reliable quantification. But the experiments showed that a coating with transparent polyelectrolytes increases the efficiency of aluminum transducers and modifies the excited phonon distribution. The adoption of polyelectrolytes to the scientific field of picosecond acoustics enables a cheap and fast fabrication of transducer layers on most surfaces. In contrast to aluminum layers the polyelectrolytes are transparent over a wide spectral range. Thus, the strain modulation can be probed from surface and back.},
  language  = {en}
}
@phdthesis{Schmidt2015,
  author    = {Schmidt, Andreas},
  title     = {Charakterisierung der Lipopolysaccharid-Bindungseigenschaften von Adh{\"a}sionsproteinen aus Salmonella-Bakteriophagen},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-79529},
  school      = {Universit{\"a}t Potsdam},
  pages     = {VIII, 114},
  year      = {2015},
  abstract  = {Die Interaktionen von komplexen Kohlenhydraten und Proteinen sind ubiquit{\"a}r. Sie spielen wichtige Rollen in vielen physiologischen Prozessen wie Zelladh{\"a}sion, Signaltransduktion sowie bei viralen Infektionen. Die molekularen Grundlagen der Interaktion sind noch nicht komplett verstanden. Ein Modellsystem f{\"u}r Kohlenhydrat-Protein-Interaktionen besteht aus Adh{\"a}sionsproteinen (Tailspikes) von Bakteriophagen, die komplexe Kohlenhydrate auf bakteriellen Oberfl{\"a}chen (O-Antigen) erkennen. Das Tailspike-Protein (TSP), das in dieser Arbeit betrachtet wurde, stammt aus dem Bakteriophagen 9NA (9NATSP). 9NATSP weist eine hohe strukturelle Homologie zum gut charakterisierten TSP des Phagen P22 (P22TSP) auf, bei einer niedriger sequenzieller {\"A}hnlichkeit. Die Substratspezifit{\"a}ten beider Tailspikes sind {\"a}hnlich mit Ausnahme der Toleranz gegen{\"u}ber den glucosylierten Formen des O-Antigens. Die Struktur der beiden Tailspikes ist bekannt, sodass sie ein geeignetes System f{\"u}r vergleichende Bindungsstudien darstellen, um die strukturellen Grundlagen f{\"u}r die Unterschiede der Spezifit{\"a}t zu untersuchen. Im Rahmen dieser Arbeit wurde der ELISA-like tailspike adsorption assay (ELITA) etabliert, um Binderpaare aus TSPs und O-Antigen zu identifizieren. Dabei wurden 9NATSP und P22TSP als Sonden eingesetzt, deren Bindung an die intakten, an die Mikrotiterplatte adsorbierten Bakterien getestet wurde. Beim Test einer Sammlung aus 44 Salmonella-St{\"a}mmen wurden St{\"a}mme identifiziert, die bindendes O-Antigen exprimieren. Gleichzeitig wurden Unterschiede in der Bindung der beiden TSPs an Salmonella-St{\"a}mme mit gleichem O-Serotyp beobachtet. Die Ergebnisse der ELITA-Messung wurden qualitativ durch eine FACS-basierte Bindungsmessung best{\"a}tigt. Zus{\"a}tzlich erm{\"o}glichte die FACS-Messung bei St{\"a}mmen, die teilweise modifizierte O-Antigene herstellen, den Anteil an Zellen mit und ohne Modifikation zu erfassen. Die Oberfl{\"a}chenplasmonresonanz (SPR)-basierten Interaktionsmessungen wurden eingesetzt, um Bindungsaffinit{\"a}ten f{\"u}r eine TSP-O-Antigen Kombination zu quantifizieren. Daf{\"u}r wurden zwei Methoden getestet, um die Oligosaccharide auf einem SPR-Chip zu immobilisieren. Zum einen wurden die enzymatisch hergestellten O-Antigenfragmente mit einem bifunktionalen Oxaminadapter derivatisiert, der eine prim{\"a}re Aminogruppe f{\"u}r die Immobilisierung bereitstellt. Ein Versuch, diese Oligosaccharidfragmente zu immobilisieren, war jedoch nicht erfolgreich. Dagegen wurde das nicht derivatisierte Polysaccharid, bestehend aus repetitivem O-Antigen und einem konservierten Kernsaccharid, erfolgreich auf einem SPR-Chip immobilisiert. Die Immobilisierung wurde durch Interaktionsmessungen mit P22TSP best{\"a}tigt. Durch die Immobilisierung des Polysaccharids sind somit quantitative SPR-Bindungsmessungen mit einem polydispersen Interaktionspartner m{\"o}glich. Eine Auswahl von Salmonella-St{\"a}mmen mit einer ausgepr{\"a}gt unterschiedlichen Bindung von 9NATSP und P22TSP im ELITA-Testsystem wurde hinsichtlich der Zusammensetzung des O-Antigens mittels HPLC, Kapillargelelektrophorese und MALDI-MS analysiert. Dabei wurden nicht-st{\"o}chiometrische Modifikationen der O-Antigene wie Acetylierung und Glucosylierung detektiert. Das Ausmaß der Glucosylierung korrelierte negativ mit der Effizienz der Bindung und des Verdaus durch die beiden TSPs, wobei der negative Effekt bei 9NATSP weniger stark ausgepr{\"a}gt war als bei P22TSP. Dies stimmt mit den Literaturdaten zu Infektivit{\"a}tsstudien mit 9NA und P22 {\"u}berein, die mit St{\"a}mmen mit vergleichbaren O-Antigenvarianten durchgef{\"u}hrt wurden. Die Korrelation zwischen der Glucosylierung und Bindungseffizienz konnte strukturell interpretiert werden. Auf Grundlage der O-Antigenanalysen sowie der Ergebnisse der ELITA- und FACS-Bindungstests wurden die Salmonella-St{\"a}mme Brancaster und Kalamu identifiziert, die ann{\"a}hernd quantitativ glucosyliertes O-Antigen exprimieren. Damit eignen sich diese St{\"a}mme f{\"u}r weiterf{\"u}hrende Studien, um die Zusammenh{\"a}nge zwischen der Spezifit{\"a}t und der Organisation der Bindestellen der beiden TSPs zu untersuchen.},
  language  = {de}
}
@phdthesis{Maerten2015,
  author    = {Maerten, Lena},
  title     = {Spectroscopic perspectives on ultrafast coupling phenomena in perovskite oxides},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-77623},
  school      = {Universit{\"a}t Potsdam},
  year      = {2015},
  abstract  = {In this thesis, I study ultrafast dynamics in perovskite oxides using time resolved broadband spectroscopy. I focus on the observation of coherent phonon propagation by time resolved Brillouin scattering: following the excition of metal transducer films with a femtosecond infrared pump pulse, coherent phonon dynamics in the GHz frequency range are triggered. Their propagation is monitored using a delayed white light probe pulse. The technique is illustrated on various thin films and multilayered samples. I apply the technique to investigate the linear and nonlinear acoustic response in bulk SrTiO_3, which displays a ferroelastic phase transition from a cubic to a tetragonal structural phase at T_a=105 K. In the linear regime, I observe a coupling of the observed acoustic phonon mode to the softening optic modes describing the phase transition. In the nonlinear regime, I find a giant slowing down of the sound velocity in the low temperature phase that is only observable for a strain amplitude exceeding the tetragonality of the material. It is attributed to a coupling of the high frequency phonons to ferroelastic domain walls in the material. I propose a new mechanism for the coupling of strain waves to the domain walls that is only effective for high amplitude strain. A detailed study of the phonon attenuation across a wide temperature range shows that the phonon attenuation at low temperatures is influenced by the domain configuration, which is determined by interface strain. Preliminary measurements on magnetic-ferroelectric multilayers reveal that the excitation fluence needs to be carefully controlled when dynamics at phase transitions are studied.},
  language  = {en}
}