@misc{ArandaSchoelzelMendezetal.2018, author = {Aranda, Juan and Sch{\"o}lzel, Mario and Mendez, Diego and Carrillo, Henry}, title = {An energy consumption model for multiModal wireless sensor networks based on wake-up radio receivers}, series = {2018 IEEE Colombian Conference on Communications and Computing (COLCOM)}, journal = {2018 IEEE Colombian Conference on Communications and Computing (COLCOM)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6820-7}, doi = {10.1109/ColComCon.2018.8466728}, pages = {6}, year = {2018}, abstract = {Energy consumption is a major concern in Wireless Sensor Networks. A significant waste of energy occurs due to the idle listening and overhearing problems, which are typically avoided by turning off the radio, while no transmission is ongoing. The classical approach for allowing the reception of messages in such situations is to use a low-duty-cycle protocol, and to turn on the radio periodically, which reduces the idle listening problem, but requires timers and usually unnecessary wakeups. A better solution is to turn on the radio only on demand by using a Wake-up Radio Receiver (WuRx). In this paper, an energy model is presented to estimate the energy saving in various multi-hop network topologies under several use cases, when a WuRx is used instead of a classical low-duty-cycling protocol. The presented model also allows for estimating the benefit of various WuRx properties like using addressing or not.}, language = {en} } @misc{DiazMendezSchoelzel2018, author = {Diaz, Sergio and Mendez, Diego and Sch{\"o}lzel, Mario}, title = {Dynamic Gallager-Humblet-Spira Algorithm for Wireless Sensor Networks}, series = {2018 IEEE Colombian Conference on Communications and Computing (COLCOM)}, journal = {2018 IEEE Colombian Conference on Communications and Computing (COLCOM)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-6820-7}, pages = {6}, year = {2018}, abstract = {The problem of constructing and maintaining a tree topology in a distributed manner is a challenging task in WSNs. This is because the nodes have limited computational and memory resources and the network changes over time. We propose the Dynamic Gallager-Humblet-Spira (D-GHS) algorithm that builds and maintains a minimum spanning tree. To do so, we divide D-GHS into four phases, namely neighbor discovery, tree construction, data collection, and tree maintenance. In the neighbor discovery phase, the nodes collect information about their neighbors and the link quality. In the tree construction, D-GHS finds the minimum spanning tree by executing the Gallager-Humblet-Spira algorithm. In the data collection phase, the sink roots the minimum spanning tree at itself, and each node sends data packets. In the tree maintenance phase, the nodes repair the tree when communication failures occur. The emulation results show that D-GHS reduces the number of control messages and the energy consumption, at the cost of a slight increase in memory size and convergence time.}, language = {en} } @misc{MuehlbauerSchroederSkoncejetal.2017, author = {M{\"u}hlbauer, Felix and Schr{\"o}der, Lukas and Skoncej, Patryk and Sch{\"o}lzel, Mario}, title = {Handling manufacturing and aging faults with software-based techniques in tiny embedded systems}, series = {18th IEEE Latin American Test Symposium (LATS 2017)}, journal = {18th IEEE Latin American Test Symposium (LATS 2017)}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-0415-1}, doi = {10.1109/LATW.2017.7906756}, pages = {6}, year = {2017}, abstract = {Non-volatile memory area occupies a large portion of the area of a chip in an embedded system. Such memories are prone to manufacturing faults, retention faults, and aging faults. The paper presents a single software based technique that allows for handling all of these fault types in tiny embedded systems without the need for hardware support. This is beneficial for low-cost embedded systems with simple memory architectures. A software infrastructure and a flow are presented that demonstrate how the presented technique is used in general for fault handling right after manufacturing and in-the-field. Moreover, a full implementation is presented for a MSP430 microcontroller, along with a discussion of the performance, overhead, and reliability impacts.}, language = {en} } @misc{MuehlbauerSchroederSchoelzel2017, author = {M{\"u}hlbauer, Felix and Schr{\"o}der, Lukas and Sch{\"o}lzel, Mario}, title = {On hardware-based fault-handling in dynamically scheduled processors}, series = {20th International Symposium on Design and Diagnostics of Electronic Circuits \& Systems (DDECS) 2017}, journal = {20th International Symposium on Design and Diagnostics of Electronic Circuits \& Systems (DDECS) 2017}, publisher = {IEEE}, address = {New York}, isbn = {978-1-5386-0472-4}, issn = {2334-3133}, doi = {10.1109/DDECS.2017.7934572}, pages = {201 -- 206}, year = {2017}, abstract = {This paper describes architectural extensions for a dynamically scheduled processor, so that it can be used in three different operation modes, ranging from high-performance, to high-reliability. With minor hardware-extensions of the control path, the resources of the superscalar data-path can be used either for high-performance execution, fail-safe-operation, or fault-tolerant-operation. This makes the processor-architecture a very good candidate for applications with dynamically changing reliability requirements, e.g. for automotive applications. The paper reports the hardware-overhead for the extensions, and investigates the performance penalties introduced by the fail-safe and fault-tolerant mode. Furthermore, a comprehensive fault simulation was carried out in order to investigate the fault-coverage of the proposed approach.}, language = {en} }