@article{SunDongOsenbergetal.2018,
  author    = {Sun, Fu and Dong, Kang and Osenberg, Markus and Hilger, Andre and Risse, Sebastian and Lu, Yan and Kamm, Paul H. and Klaus, Manuela and Markoetter, Henning and Garcia-Moreno, Francisco and Arlt, Tobias and Manke, Ingo},
  title     = {Visualizing the morphological and compositional evolution of the interface of InLi-anode|thio-LISION electrolyte in an all-solid-state Li-S cell by in operando synchrotron X-ray tomography and energy dispersive diffraction},
  series = {Journal of materials chemistry : A, Materials for energy and sustainability},
  volume    = {6},
  journal   = {Journal of materials chemistry : A, Materials for energy and sustainability},
  number    = {45},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {2050-7488},
  doi       = {10.1039/c8ta08821g},
  pages     = {22489 -- 22496},
  year      = {2018},
  abstract  = {Dynamic and direct visualization of interfacial evolution is helpful in gaining fundamental knowledge of all-solid-state-lithium battery working/degradation mechanisms and clarifying future research directions for constructing next-generation batteries. Herein, in situ and in operando synchrotron X-ray tomography and energy dispersive diffraction were simultaneously employed to record the morphological and compositional evolution of the interface of InLi-anode|sulfide-solid-electrolyte during battery cycling. Compelling morphological evidence of interfacial degradation during all-solid-state-lithium battery operation has been directly visualized by tomographic measurement. The accompanying energy dispersive diffraction results agree well with the observed morphological deterioration and the recorded electrochemical performance. It is concluded from the current investigation that a fundamental understanding of the phenomena occurring at the solid-solid electrode|electrolyte interface during all-solid-state-lithium battery cycling is critical for future progress in cell performance improvement and may determine its final commercial viability.},
  language  = {en}
}
@article{MishurovaCabezaThiedeetal.2018,
  author    = {Mishurova, Tatiana and Cabeza, Sandra and Thiede, Tobias and Nadammal, Naresh and Kromm, Arne and Klaus, Manuela and Genzel, Christoph and Haberland, Christoph and Bruno, Giovanni},
  title     = {The Influence of the Support Structure on Residual Stress and Distortion in SLM Inconel 718 Parts},
  series = {Metallurgical and Materials Transactions A},
  volume    = {49A},
  journal   = {Metallurgical and Materials Transactions A},
  number    = {7},
  publisher = {Springer},
  address   = {New York},
  issn      = {1073-5623},
  doi       = {10.1007/s11661-018-4653-9},
  pages     = {3038 -- 3046},
  year      = {2018},
  abstract  = {The effect of support structure and of removal from the base plate on the residual stress state in selective laser melted IN718 parts was studied by means of synchrotron X-ray diffraction. The residual stresses in subsurface region of two elongated prisms in as-built condition and after removal from the base plate were determined. One sample was directly built on a base plate and another one on a support structure. Also, the distortion on the top surface due to stress release was measured by contact profilometry. High tensile residual stress values were found, with pronounced stress gradient along the hatching direction. In the sample on support, stress redistribution took place after removal from the base plate, as opposed to simple stress relaxation for the sample without support. The sample on support structure showed larger distortion compared to sample without support. We conclude that the use of a support decreases stress values but stress-relieving heat treatments are still needed.},
  language  = {en}
}
@article{MishurovaCabezaArtztetal.2017,
  author    = {Mishurova, Tatiana and Cabeza, Sandra and Artzt, Katia and Haubrich, Jan and Klaus, Manuela and Genzel, Christoph and Requena, Guillermo and Bruno, Giovanni},
  title     = {An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V},
  series = {Materials},
  volume    = {10},
  journal   = {Materials},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma10040348},
  pages     = {14},
  year      = {2017},
  abstract  = {Ti-6Al-4V bridges were additively fabricated by selective laser melting (SLM) under different scanning speed conditions, to compare the effect of process energy density on the residual stress state. Subsurface lattice strain characterization was conducted by means of synchrotron diffraction in energy dispersive mode. High tensile strain gradients were found at the frontal surface for samples in an as-built condition. The geometry of the samples promotes increasing strains towards the pillar of the bridges. We observed that the higher the laser energy density during fabrication, the lower the lattice strains. A relief of lattice strains takes place after heat treatment.},
  language  = {en}
}