@article{LangKoehnenWarbyetal.2021,
  author    = {Lang, Felix and K{\"o}hnen, Eike and Warby, Jonathan and Xu, Ke and Grischek, Max and Wagner, Philipp and Neher, Dieter and Korte, Lars and Albrecht, Steve and Stolterfoht, Martin},
  title     = {Revealing fundamental efficiency limits of monolithic perovskite/silicon tandem photovoltaics through subcell characterization},
  series = {ACS Energy Letters},
  volume    = {6},
  journal   = {ACS Energy Letters},
  number    = {11},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2380-8195},
  doi       = {10.1021/acsenergylett.1c01783},
  pages     = {3982 -- 3991},
  year      = {2021},
  abstract  = {Perovskite/silicon tandem photovoltaics (PVs) promise to accelerate the decarbonization of our energy systems. Here, we present a thorough subcell diagnosis methodology to reveal deep insights into the practical efficiency limitations of state-of-the-art perovskite/silicon tandem PVs. Our subcell selective intensity-dependent photoluminescence (PL) and injection-dependent electroluminescence (EL) measurements allow independent assessment of pseudo-V-OC and power conversion efficiencies (PCEs) for both subcells. We reveal identical metrics from PL and EL, which implies well-aligned energy levels throughout the entire cell. Relatively large ideality factors and insufficient charge extraction, however, cause each a fill factor penalty of about 6\% (absolute). Using partial device stacks, we then identify significant losses in standard perovskite subcells due to bulk and interfacial recombination. Lastly, we present strategies to minimize these losses using triple halide (CsFAPb(IBrCI)(3)) based perovskites. Our results give helpful feedback for device development and lay the foundation toward advanced perovskite/silicon tandem PVs capable of exceeding 33\% PCE.},
  language  = {en}
}
@article{KegelmannTockhornWolffetal.2019,
  author    = {Kegelmann, Lukas and Tockhorn, Philipp and Wolff, Christian Michael and M{\´a}rquez, Jos{\´e} A. and Caicedo D{\´a}vila, Sebasti{\´a}n and Korte, Lars and Unold, Thomas and Loevenich, Wilfried and Neher, Dieter and Rech, Bernd and Albrecht, Steve},
  title     = {Mixtures of Dopant-Free Spiro-OMeTAD and Water-Free PEDOT as a Passivating Hole Contact in Perovskite Solar Cells},
  series = {ACS applied materials \& interfaces},
  volume    = {11},
  journal   = {ACS applied materials \& interfaces},
  number    = {9},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1944-8244},
  doi       = {10.1021/acsami.9b01332},
  pages     = {9172 -- 9181},
  year      = {2019},
  abstract  = {Doped spiro-OMeTAD at present is the most commonly used hole transport material (HTM) in n-i-p-type perovskite solar cells, enabling high efficiencies around 22\%. However, the required dopants were shown to induce nonradiative recombination of charge carriers and foster degradation of the solar cell. Here, in a novel approach, highly conductive and inexpensive water-free poly(3,4-ethylenedioxythiophene) (PEDOT) is used to replace these dopants. The resulting spiro-OMeTAD/PEDOT (SpiDOT) mixed films achieve higher lateral conductivities than layers of doped spiro-OMeTAD. Furthermore, combined transient and steady-state photoluminescence studies reveal a passivating effect of PEDOT, suppressing nonradiative recombination losses at the perovskite/HTM interface. This enables excellent quasi-Fermi level splitting values of up to 1.24 eV in perovskite/SpiDOT layer stacks and high open-circuit voltages (V-OC) up to 1.19 V in complete solar cells. Increasing the amount of dopant-free spiro-OMeTAD in SpiDOT layers is shown to enhance hole extraction and thereby improves the fill factor in solar cells. As a consequence, stabilized efficiencies up to 18.7\% are realized, exceeding cells with doped spiro-OMeTAD as a HTM in this study. Moreover, to the best of our knowledge, these results mark the lowest nonradiative recombination loss in the V-OC (140 mV with respect to the Shockley-Queisser limit) and highest efficiency reported so far for perovskite solar cells using PEDOT as a HTM.},
  language  = {en}
}
@article{KegelmannWolffAwinoetal.2017,
  author    = {Kegelmann, Lukas and Wolff, Christian Michael and Awino, Celline and Lang, Felix and Unger, Eva L. and Korte, Lars and Dittrich, Thomas and Neher, Dieter and Rech, Bernd and Albrecht, Steve},
  title     = {It Takes Two to Tango-Double-Layer Selective Contacts in Perovskite Solar Cells for Improved Device Performance and Reduced Hysteresis},
  series = {ACS applied materials \& interfaces},
  volume    = {9},
  journal   = {ACS applied materials \& interfaces},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1944-8244},
  doi       = {10.1021/acsami.7b00900},
  pages     = {17246 -- 17256},
  year      = {2017},
  abstract  = {Solar cells made from inorganic organic perovskites have gradually approached market requirements as their efficiency and stability have improved tremendously in recent years. Planar low-temperature processed perovskite solar cells are advantageous for possible large-scale production but are more prone to exhibiting photocurrent hysteresis, especially in the regular n-i-p structure. Here, a systematic characterization of different electron selective contacts with a variety of chemical and electrical properties in planar n-i-p devices processed below 180 degrees C is presented. The inorganic metal oxides TiO2 and SnO2, the organic fullerene derivatives C-60, PCBM, and ICMA, as well as double-layers with a metal oxide/PCBM structure are used as electron transport materials (ETMs). Perovskite layers deposited atop, the different ETMs with the herein applied fabrication method show a similar morphology according to scanning electron microscopy. Further, surface photovoltage spectroscopy measurements indicate comparable perovskite absorber qualities on all ETMs, except TiO2, which shows a more prominent influence of defect states. Transient photoluminescence studies together with current voltage scans over a broad range of scan speeds reveal faster charge extraction, less pronounced hysteresis effects, and higher efficiencies for devices with fullerene compared to those with metal oxide ETMs. Beyond this, only double-layer ETM structures substantially diminish hysteresis effects for all performed scan speeds and strongly enhance the power conversion efficiency up to a champion stabilized value of 18.0\%. The results indicate reduced recombination losses for a double-layer TiO2/PCBM contact design: First, a reduction of shunt paths through the fullerene to the ITO layer. Second, an improved hole blocking by the wide band gap metal oxide. Third, decreased transport losses due to an energetically more favorable contact, as implied by photoelectron spectroscopy measurements. The herein demonstrated improvements of multilayer selective contacts may serve as a general design guideline for perovskite solar cells.},
  language  = {en}
}
@article{JoštAlbrechtKegelmannetal.2017,
  author    = {Jošt, Marko and Albrecht, Steve and Kegelmann, Lukas and Wolff, Christian Michael and Lang, Felix and Lipovšek, Benjamin and Krč, Janez and Korte, Lars and Neher, Dieter and Rech, Bernd and Topič, Marko},
  title     = {Efficient light management by textured nanoimprinted layers for perovskite solar cells},
  series = {ACS photonics},
  volume    = {4},
  journal   = {ACS photonics},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2330-4022},
  doi       = {10.1021/acsphotonics.7b00138},
  pages     = {1232 -- 1239},
  year      = {2017},
  abstract  = {Inorganic-organic perovskites like methylammonium-lead-iodide have proven to be an effective class of 17 materials for fabricating efficient solar cells. To improve their performance, light management techniques using textured surfaces, similar to those used in established solar cell technologies, should be considered. Here, we apply a light management foil created by UV nanoimprint lithography on the glass side of an inverted (p-i-n) perovskite solar cell with 16.3\% efficiency. The obtained 1 mA cm(-2) increase in the short-circuit current density translates to a relative improvement in cell performance of 5\%, which results in a power conversion efficiency of 17.1\%. Optical 3D simulations based on experimentally obtained parameters were used to support the experimental findings. A good match between the simulated and experimental data was obtained, validating the model. Optical simulations reveal that the main improvement in device performance is due to a reduction in total reflection and that relative improvement in the short-circuit current density of up to 10\% is possible for large-area devices. Therefore, our results present the potential of light management foils for improving the device performance of perovskite solar cells and pave the way for further use of optical simulations in the field of perovskite solar cells.},
  language  = {en}
}
@article{GrischekCaprioglioZhangetal.2022,
  author    = {Grischek, Max and Caprioglio, Pietro and Zhang, Jiahuan and Pena-Camargo, Francisco and Sveinbjornsson, Kari and Zu, Fengshuo and Menzel, Dorothee and Warby, Jonathan H. and Li, Jinzhao and Koch, Norbert and Unger, Eva and Korte, Lars and Neher, Dieter and Stolterfoht, Martin and Albrecht, Steve},
  title     = {Efficiency Potential and Voltage Loss of Inorganic CsPbI2Br Perovskite Solar Cells},
  series = {Solar RRL},
  volume    = {6},
  journal   = {Solar RRL},
  number    = {11},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {2367-198X},
  doi       = {10.1002/solr.202200690},
  pages     = {12},
  year      = {2022},
  abstract  = {Inorganic perovskite solar cells show excellent thermal stability, but the reported power conversion efficiencies are still lower than for organic-inorganic perovskites. This is mainly caused by lower open-circuit voltages (V(OC)s). Herein, the reasons for the low V-OC in inorganic CsPbI2Br perovskite solar cells are investigated. Intensity-dependent photoluminescence measurements for different layer stacks reveal that n-i-p and p-i-n CsPbI2Br solar cells exhibit a strong mismatch between quasi-Fermi level splitting (QFLS) and V-OC. Specifically, the CsPbI2Br p-i-n perovskite solar cell has a QFLS-e center dot V-OC mismatch of 179 meV, compared with 11 meV for a reference cell with an organic-inorganic perovskite of similar bandgap. On the other hand, this study shows that the CsPbI2Br films with a bandgap of 1.9 eV have a very low defect density, resulting in an efficiency potential of 20.3\% with a MeO-2PACz hole-transporting layer and 20.8\% on compact TiO2. Using ultraviolet photoelectron spectroscopy measurements, energy level misalignment is identified as a possible reason for the QFLS-e center dot V-OC mismatch and strategies for overcoming this V-OC limitation are discussed. This work highlights the need to control the interfacial energetics in inorganic perovskite solar cells, but also gives promise for high efficiencies once this issue is resolved.},
  language  = {en}
}
@article{BraungerMundtWolffetal.2018,
  author    = {Braunger, Steffen and Mundt, Laura E. and Wolff, Christian Michael and Mews, Mathias and Rehermann, Carolin and Jost, Marko and Tejada, Alvaro and Eisenhauer, David and Becker, Christiane and Andres Guerra, Jorge and Unger, Eva and Korte, Lars and Neher, Dieter and Schubert, Martin C. and Rech, Bernd and Albrecht, Steve},
  title     = {Cs(x)FA(1-x)Pb(l(1-y)Br(y))(3) Perovskite Compositions},
  series = {The journal of physical chemistry : C, Nanomaterials and interfaces},
  volume    = {122},
  journal   = {The journal of physical chemistry : C, Nanomaterials and interfaces},
  number    = {30},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {1932-7447},
  doi       = {10.1021/acs.jpcc.8b06459},
  pages     = {17123 -- 17135},
  year      = {2018},
  abstract  = {We report on the formation of wrinkle-patterned surface morphologies in cesium formamidinium-based Cs(x)FA(1-y)Pb(I1-yBry)(3) perovskite compositions with x = 0-0.3 and y = 0-0.3 under various spin-coating conditions. By varying the Cs and Br contents, the perovskite precursor solution concentration and the spin-coating procedure, the occurrence and characteristics of the wrinkle-shaped morphology can be tailored systematically. Cs(0.17)FA(0.83)Pb(I0.83Br0.17)(3) perovskite layers were analyzed regarding their surface roughness, microscopic structure, local and overall composition, and optoelectronic properties. Application of these films in p-i-n perovskite solar cells (PSCs) with indium-doped tin oxide/NiOx/perovskite/C-60/bathocuproine/Cu architecture resulted in up to 15.3 and 17.0\% power conversion efficiency for the flat and wrinkled morphology, respectively. Interestingly, we find slightly red-shifted photoluminescence (PL) peaks for wrinkled areas and we are able to directly correlate surface topography with PL peak mapping. This is attributed to differences in the local grain size, whereas there is no indication for compositional demixing in the films. We show that the perovskite composition, crystallization kinetics, and layer thickness strongly influence the formation of wrinkles which is proposed to be related to the release of compressive strain during perovskite crystallization. Our work helps us to better understand film formation and to further improve the efficiency of PSCs with widely used mixed-perovskite compositions.},
  language  = {en}
}