@article{ZhangChenArminetal.2017, author = {Zhang, Kai and Chen, Zhiming and Armin, Ardalan and Dong, Sheng and Xia, Ruoxi and Yip, Hin-Lap and Shoaee, Safa and Huang, Fei and Cao, Yong}, title = {Efficient large area organic solar cells processed by blade-coating with single-component green solvent}, series = {Solar Rrl}, volume = {2}, journal = {Solar Rrl}, number = {1}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {2367-198X}, doi = {10.1002/solr.201700169}, pages = {9}, year = {2017}, abstract = {While the performance of laboratory-scale organic solar cells (OSCs) continues to grow, development of high efficiency large area OSCs remains a big challenge. Although a few attempts to produce large area organic solar cells (OSCs) have been reported, there are still challenges on the way to realizing efficient module devices, such as the low compatibility of the thickness-sensitive active layer with large area coating techniques, the frequent need for toxic solvents and tedious optimization processes used during device fabrication. In this work, highly efficient thickness-insensitive OSCs based on PTB7-Th:PC71BM that processed with single-component green solvent 2-methylanisole are presented, in which both junction thickness limitation and solvent toxicity issues are simultaneously addressed. Careful investigation reveals that this green solvent prevents the evolution of PC71BM into large area clusters resulting in reduced charge carrier recombination, and largely eliminates trapping centers, and thus improves the thickness tolerance of the films. These findings enable us to address the scalability and solvent toxicity issues and to fabricate a 16 cm(2) OSC with doctor-blade coating with a state-of-the-art power conversion efficiency of 7.5\% using green solvent.}, language = {en} } @article{YazmaciyanStolterfohtBurnetal.2018, author = {Yazmaciyan, Aren and Stolterfoht, Martin and Burn, Paul L. and Lin, Qianqian and Meredith, Paul and Armin, Ardalan}, title = {Recombination losses above and below the transport percolation threshold in bulk heterojunction organic solar cells}, series = {Advanced energy materials}, volume = {8}, journal = {Advanced energy materials}, number = {18}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201703339}, pages = {8}, year = {2018}, abstract = {Achieving the highest power conversion efficiencies in bulk heterojunction organic solar cells requires a morphology that delivers electron and hole percolation pathways for optimized transport, plus sufficient donor:acceptor contact area for near unity charge transfer state formation. This is a significant structural challenge, particularly in semiconducting polymer:fullerene systems. This balancing act in the model high efficiency PTB7:PC70BM blend is studied by tuning the donor:acceptor ratio, with a view to understanding the recombination loss mechanisms above and below the fullerene transport percolation threshold. The internal quantum efficiency is found to be strongly correlated to the slower carrier mobility in agreement with other recent studies. Furthermore, second-order recombination losses dominate the shape of the current density-voltage curve in efficient blend combinations, where the fullerene phase is percolated. However, below the charge transport percolation threshold, there is an electric-field dependence of first-order losses, which includes electric-field-dependent photogeneration. In the intermediate regime, the fill factor appears to be limited by both first- and second-order losses. These findings provide additional basic understanding of the interplay between the bulk heterojunction morphology and the order of recombination in organic solar cells. They also shed light on the limitations of widely used transport models below the percolation threshold.}, language = {en} } @article{VollbrechtBrus2021, author = {Vollbrecht, Joachim and Brus, Viktor V.}, title = {Effects of recombination order on open-circuit voltage decay measurements of organic and perovskite solar cells}, series = {Energies : open-access journal of related scientific research, technology development and studies in policy and management / Molecular Diversity Preservation International (MDPI)}, volume = {14}, journal = {Energies : open-access journal of related scientific research, technology development and studies in policy and management / Molecular Diversity Preservation International (MDPI)}, number = {16}, publisher = {MDPI}, address = {Basel}, issn = {1996-1073}, doi = {10.3390/en14164800}, pages = {16}, year = {2021}, abstract = {Non-geminate recombination, as one of the most relevant loss mechanisms in organic and perovskite solar cells, deserves special attention in research efforts to further increase device performance. It can be subdivided into first, second, and third order processes, which can be elucidated by the effects that they have on the time-dependent open-circuit voltage decay. In this study, analytical expressions for the open-circuit voltage decay exhibiting one of the aforementioned recombination mechanisms were derived. It was possible to support the analytical models with experimental examples of three different solar cells, each of them dominated either by first (PBDBT:CETIC-4F), second (PM6:Y6), or third (irradiated CH3NH3PbI3) order recombination. Furthermore, a simple approach to estimate the dominant recombination process was also introduced and tested on these examples. Moreover, limitations of the analytical models and the measurement technique itself were discussed.}, language = {en} } @misc{ShoaeeStolterfohtNeher2018, author = {Shoaee, Safa and Stolterfoht, Martin and Neher, Dieter}, title = {The Role of Mobility on Charge Generation, Recombination, and Extraction in Polymer-Based Solar Cells}, series = {dvanced energy materials}, volume = {8}, journal = {dvanced energy materials}, number = {28}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201703355}, pages = {20}, year = {2018}, abstract = {Organic semiconductors are of great interest for a broad range of optoelectronic applications due to their solution processability, chemical tunability, highly scalable fabrication, and mechanical flexibility. In contrast to traditional inorganic semiconductors, organic semiconductors are intrinsically disordered systems and therefore exhibit much lower charge carrier mobilities-the Achilles heel of organic photovoltaic cells. In this progress review, the authors discuss recent important developments on the impact of charge carrier mobility on the charge transfer state dissociation, and the interplay of free charge extraction and recombination. By comparing the mobilities on different timescales obtained by different techniques, the authors highlight the dispersive nature of these materials and how this reflects on the key processes defining the efficiency of organic photovoltaics.}, language = {en} } @article{ShoaeeSannaSforazzini2021, author = {Shoaee, Safa and Sanna, Anna Laura and Sforazzini, Giuseppe}, title = {Elucidating charge generation in green-solvent processed organic solar cells}, series = {Molecules : a journal of synthetic chemistry and natural product chemistry / Molecular Diversity Preservation International}, volume = {26}, journal = {Molecules : a journal of synthetic chemistry and natural product chemistry / Molecular Diversity Preservation International}, number = {24}, publisher = {MDPI}, address = {Basel}, issn = {1420-3049}, doi = {10.3390/molecules26247439}, pages = {13}, year = {2021}, abstract = {Organic solar cells have the potential to become the cheapest form of electricity. Rapid increase in the power conversion efficiency of organic solar cells (OSCs) has been achieved with the development of non-fullerene small-molecule acceptors. Next generation photovoltaics based upon environmentally benign "green solvent" processing of organic semiconductors promise a step-change in the adaptability and versatility of solar technologies and promote sustainable development. However, high-performing OSCs are still processed by halogenated (non-environmentally friendly) solvents, so hindering their large-scale manufacture. In this perspective, we discuss the recent progress in developing highly efficient OSCs processed from eco-compatible solvents, and highlight research challenges that should be addressed for the future development of high power conversion efficiencies devices.}, language = {en} } @phdthesis{Schubert2014, author = {Schubert, Marcel}, title = {Elementary processes in layers of electron transporting Donor-acceptor copolymers : investigation of charge transport and application to organic solar cells}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-70791}, school = {Universit{\"a}t Potsdam}, year = {2014}, abstract = {Donor-acceptor (D-A) copolymers have revolutionized the field of organic electronics over the last decade. Comprised of a electron rich and an electron deficient molecular unit, these copolymers facilitate the systematic modification of the material's optoelectronic properties. The ability to tune the optical band gap and to optimize the molecular frontier orbitals as well as the manifold of structural sites that enable chemical modifications has created a tremendous variety of copolymer structures. Today, these materials reach or even exceed the performance of amorphous inorganic semiconductors. Most impressively, the charge carrier mobility of D-A copolymers has been pushed to the technologically important value of 10 cm^{2}V^{-1}s^{-1}. Furthermore, owed to their enormous variability they are the material of choice for the donor component in organic solar cells, which have recently surpassed the efficiency threshold of 10\%. Because of the great number of available D-A copolymers and due to their fast chemical evolution, there is a significant lack of understanding of the fundamental physical properties of these materials. Furthermore, the complex chemical and electronic structure of D-A copolymers in combination with their semi-crystalline morphology impede a straightforward identification of the microscopic origin of their superior performance. In this thesis, two aspects of prototype D-A copolymers were analysed. These are the investigation of electron transport in several copolymers and the application of low band gap copolymers as acceptor component in organic solar cells. In the first part, the investigation of a series of chemically modified fluorene-based copolymers is presented. The charge carrier mobility varies strongly between the different derivatives, although only moderate structural changes on the copolymers structure were made. Furthermore, rather unusual photocurrent transients were observed for one of the copolymers. Numerical simulations of the experimental results reveal that this behavior arises from a severe trapping of electrons in an exponential distribution of trap states. Based on the comparison of simulation and experiment, the general impact of charge carrier trapping on the shape of photo-CELIV and time-of-flight transients is discussed. In addition, the high performance naphthalenediimide (NDI)-based copolymer P(NDI2OD-T2) was characterized. It is shown that the copolymer posses one of the highest electron mobilities reported so far, which makes it attractive to be used as the electron accepting component in organic photovoltaic cells.\par Solar cells were prepared from two NDI-containing copolymers, blended with the hole transporting polymer P3HT. I demonstrate that the use of appropriate, high boiling point solvents can significantly increase the power conversion efficiency of these devices. Spectroscopic studies reveal that the pre-aggregation of the copolymers is suppressed in these solvents, which has a strong impact on the blend morphology. Finally, a systematic study of P3HT:P(NDI2OD-T2) blends is presented, which quantifies the processes that limit the efficiency of devices. The major loss channel for excited states was determined by transient and steady state spectroscopic investigations: the majority of initially generated electron-hole pairs is annihilated by an ultrafast geminate recombination process. Furthermore, exciton self-trapping in P(NDI2OD-T2) domains account for an additional reduction of the efficiency. The correlation of the photocurrent to microscopic morphology parameters was used to disclose the factors that limit the charge generation efficiency. Our results suggest that the orientation of the donor and acceptor crystallites relative to each other represents the main factor that determines the free charge carrier yield in this material system. This provides an explanation for the overall low efficiencies that are generally observed in all-polymer solar cells.}, language = {en} } @phdthesis{Roland2017, author = {Roland, Steffen}, title = {Charge carrier recombination and open circuit voltage in organic solar cells}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-397721}, school = {Universit{\"a}t Potsdam}, pages = {VI, 145}, year = {2017}, abstract = {Tremendous progress in the development of thin film solar cell techniques has been made over the last decade. The field of organic solar cells is constantly developing, new material classes like Perowskite solar cells are emerging and different types of hybrid organic/inorganic material combinations are being investigated for their physical properties and their applicability in thin film electronics. Besides typical single-junction architectures for solar cells, multi-junction concepts are also being investigated as they enable the overcoming of theoretical limitations of a single-junction. In multi-junction devices each sub-cell operates in different wavelength regimes and should exhibit optimized band-gap energies. It is exactly this tunability of the band-gap energy that renders organic solar cell materials interesting candidates for multi-junction applications. Nevertheless, only few attempts have been made to combine inorganic and organic solar cells in series connected multi-junction architectures. Even though a great diversity of organic solar cells exists nowadays, their open circuit voltage is usually low compared to the band-gap of the active layer. Hence, organic low band-gap solar cells in particular show low open circuit voltages and the key factors that determine the voltage losses are not yet fully understood. Besides open circuit voltage losses the recombination of charges in organic solar cells is also a prevailing research topic, especially with respect to the influence of trap states. The exploratory focus of this work is therefore set, on the one hand, on the development of hybrid organic/inorganic multi-junctions and, on the other hand, on gaining a deeper understanding of the open circuit voltage and the recombination processes of organic solar cells. In the first part of this thesis, the development of a hybrid organic/inorganic triple-junction will be discussed which showed at that time (Jan. 2015) a record power conversion efficiency of 11.7\%. The inorganic sub-cells of these devices consist of hydrogenated amorphous silicon and were delivered by the Competence Center Thin-Film and Nanotechnology for Photovoltaics in Berlin. Different recombination contacts and organic sub-cells were tested in conjunction with these inorganic sub-cells on the basis of optical modeling predictions for the optimal layer thicknesses to finally reach record efficiencies for this type of solar cells. In the second part, organic model systems will be investigated to gain a better understanding of the fundamental loss mechanisms that limit the open circuit voltage of organic solar cells. First, bilayer systems with different orientation of the donor and acceptor molecules were investigated to study the influence of the donor/acceptor orientation on non-radiative voltage loss. Secondly, three different bulk heterojunction solar cells all comprising the same amount of fluorination and the same polymer backbone in the donor component were examined to study the influence of long range electrostatics on the open circuit voltage. Thirdly, the device performance of two bulk heterojunction solar cells was compared which consisted of the same donor polymer but used different fullerene acceptor molecules. By this means, the influence of changing the energetics of the acceptor component on the open circuit voltage was investigated and a full analysis of the charge carrier dynamics was presented to unravel the reasons for the worse performance of the solar cell with the higher open circuit voltage. In the third part, a new recombination model for organic solar cells will be introduced and its applicability shown for a typical low band-gap cell. This model sheds new light on the recombination process in organic solar cells in a broader context as it re-evaluates the recombination pathway of charge carriers in devices which show the presence of trap states. Thereby it addresses a current research topic and helps to resolve alleged discrepancies which can arise from the interpretation of data derived by different measurement techniques.}, language = {en} } @article{RanLoveHeiberetal.2018, author = {Ran, Niva A. and Love, John A. and Heiber, Michael C. and Jiao, Xuechen and Hughes, Michael P. and Karki, Akchheta and Wang, Ming and Brus, Viktor V. and Wang, Hengbin and Neher, Dieter and Ade, Harald and Bazan, Guillermo C. and Thuc-Quyen Nguyen,}, title = {Charge generation and recombination in an organic solar cell with low energetic offsets}, series = {dvanced energy materials}, volume = {8}, journal = {dvanced energy materials}, number = {5}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201701073}, pages = {12}, year = {2018}, abstract = {Organic bulk heterojunction (BHJ) solar cells require energetic offsets between the donor and acceptor to obtain high short-circuit currents (J(SC)) and fill factors (FF). However, it is necessary to reduce the energetic offsets to achieve high open-circuit voltages (V-OC). Recently, reports have highlighted BHJ blends that are pushing at the accepted limits of energetic offsets necessary for high efficiency. Unfortunately, most of these BHJs have modest FF values. How the energetic offset impacts the solar cell characteristics thus remains poorly understood. Here, a comprehensive characterization of the losses in a polymer:fullerene BHJ blend, PIPCP:phenyl-C61-butyric acid methyl ester (PC61BM), that achieves a high V-OC (0.9 V) with very low energy losses (E-loss = 0.52 eV) from the energy of absorbed photons, a respectable J(SC) (13 mA cm(-2)), but a limited FF (54\%) is reported. Despite the low energetic offset, the system does not suffer from field-dependent generation and instead it is characterized by very fast nongeminate recombination and the presence of shallow traps. The charge-carrier losses are attributed to suboptimal morphology due to high miscibility between PIPCP and PC61BM. These results hold promise that given the appropriate morphology, the J(SC), V-OC, and FF can all be improved, even with very low energetic offsets.}, language = {en} } @article{PranavBenduhnNymanetal.2021, author = {Pranav, Manasi and Benduhn, Johannes and Nyman, Mathias and Hosseini, Seyed Mehrdad and Kublitski, Jonas and Shoaee, Safa and Neher, Dieter and Leo, Karl and Spoltore, Donato}, title = {Enhanced charge selectivity via anodic-C60 layer reduces nonradiative losses in organic solar cells}, series = {ACS applied materials \& interfaces}, volume = {13}, journal = {ACS applied materials \& interfaces}, number = {10}, publisher = {American Chemical Society}, address = {Washington}, issn = {1944-8244}, doi = {10.1021/acsami.1c00049}, pages = {12603 -- 12609}, year = {2021}, abstract = {Interfacial layers in conjunction with suitable charge-transport layers can significantly improve the performance of optoelectronic devices by facilitating efficient charge carrier injection and extraction. This work uses a neat C-60 interlayer on the anode to experimentally reveal that surface recombination is a significant contributor to nonradiative recombination losses in organic solar cells. These losses are shown to proportionally increase with the extent of contact between donor molecules in the photoactive layer and a molybdenum oxide (MoO3) hole extraction layer, proven by calculating voltage losses in low- and high-donor-content bulk heterojunction device architectures. Using a novel in-device determination of the built-in voltage, the suppression of surface recombination, due to the insertion of a thin anodic-C-60 interlayer on MoO3, is attributed to an enhanced built-in potential. The increased built-in voltage reduces the presence of minority charge carriers at the electrodes-a new perspective on the principle of selective charge extraction layers. The benefit to device efficiency is limited by a critical interlayer thickness, which depends on the donor material in bilayer devices. Given the high popularity of MoO3 as an efficient hole extraction and injection layer and the increasingly popular discussion on interfacial phenomena in organic optoelectronic devices, these findings are relevant to and address different branches of organic electronics, providing insights for future device design.}, language = {en} } @article{PhuongHosseiniSandbergetal.2020, author = {Phuong, Le Quang and Hosseini, Seyed Mehrdad and Sandberg, Oskar J. and Zou, Yingping and Woo, Han Young and Neher, Dieter and Shoaee, Safa}, title = {Quantifying quasi-fermi level splitting and open-circuit voltage losses in highly efficient nonfullerene organic solar cells}, series = {Solar RRL}, volume = {5}, journal = {Solar RRL}, number = {1}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {2367-198X}, doi = {10.1002/solr.202000649}, pages = {6}, year = {2020}, abstract = {The power conversion efficiency (PCE) of state-of-the-art organic solar cells is still limited by significant open-circuit voltage (V-OC) losses, partly due to the excitonic nature of organic materials and partly due to ill-designed architectures. Thus, quantifying different contributions of the V-OC losses is of importance to enable further improvements in the performance of organic solar cells. Herein, the spectroscopic and semiconductor device physics approaches are combined to identify and quantify losses from surface recombination and bulk recombination. Several state-of-the-art systems that demonstrate different V-OC losses in their performance are presented. By evaluating the quasi-Fermi level splitting (QFLS) and the V-OC as a function of the excitation fluence in nonfullerene-based PM6:Y6, PM6:Y11, and fullerene-based PPDT2FBT:PCBM devices with different architectures, the voltage losses due to different recombination processes occurring in the active layers, the transport layers, and at the interfaces are assessed. It is found that surface recombination at interfaces in the studied solar cells is negligible, and thus, suppressing the non-radiative recombination in the active layers is the key factor to enhance the PCE of these devices. This study provides a universal tool to explain and further improve the performance of recently demonstrated high-open-circuit-voltage organic solar cells.}, language = {en} } @misc{PhuongHosseiniSandbergetal.2020, author = {Phuong, Le Quang and Hosseini, Seyed Mehrdad and Sandberg, Oskar J. and Zou, Yingping and Woo, Han Young and Neher, Dieter and Shoaee, Safa}, title = {Quantifying quasi-fermi level splitting and open-circuit voltage losses in highly efficient nonfullerene organic solar cells}, series = {Zweitver{\"o}ffentlichungen der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, journal = {Zweitver{\"o}ffentlichungen der Universit{\"a}t Potsdam : Mathematisch-Naturwissenschaftliche Reihe}, number = {1}, issn = {1866-8372}, doi = {10.25932/publishup-57001}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-570018}, pages = {8}, year = {2020}, abstract = {The power conversion efficiency (PCE) of state-of-the-art organic solar cells is still limited by significant open-circuit voltage (V-OC) losses, partly due to the excitonic nature of organic materials and partly due to ill-designed architectures. Thus, quantifying different contributions of the V-OC losses is of importance to enable further improvements in the performance of organic solar cells. Herein, the spectroscopic and semiconductor device physics approaches are combined to identify and quantify losses from surface recombination and bulk recombination. Several state-of-the-art systems that demonstrate different V-OC losses in their performance are presented. By evaluating the quasi-Fermi level splitting (QFLS) and the V-OC as a function of the excitation fluence in nonfullerene-based PM6:Y6, PM6:Y11, and fullerene-based PPDT2FBT:PCBM devices with different architectures, the voltage losses due to different recombination processes occurring in the active layers, the transport layers, and at the interfaces are assessed. It is found that surface recombination at interfaces in the studied solar cells is negligible, and thus, suppressing the non-radiative recombination in the active layers is the key factor to enhance the PCE of these devices. This study provides a universal tool to explain and further improve the performance of recently demonstrated high-open-circuit-voltage organic solar cells.}, language = {en} } @phdthesis{PerdigonToro2022, author = {Perdig{\´o}n-Toro, Lorena}, title = {On the Generation and Fate of Free Carriers in Non-Fullerene Acceptor Organic Solar Cells}, doi = {10.25932/publishup-55807}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-558072}, school = {Universit{\"a}t Potsdam}, pages = {ix, 191}, year = {2022}, abstract = {Organic solar cells offer an efficient and cost-effective alternative for solar energy harvesting. This type of photovoltaic cell typically consists of a blend of two organic semiconductors, an electron donating polymer and a low molecular weight electron acceptor to create what is known as a bulk heterojunction (BHJ) morphology. Traditionally, fullerene-based acceptors have been used for this purpose. In recent years, the development of new acceptor molecules, so-called non-fullerene acceptors (NFA), has breathed new life into organic solar cell research, enabling record efficiencies close to 19\%. Today, NFA-based solar cells are approaching their inorganic competitors in terms of photocurrent generation, but lag in terms of open circuit voltage (V_OC). Interestingly, the V_OC of these cells benefits from small offsets of orbital energies at the donor-NFA interface, although previous knowledge considered large energy offsets to be critical for efficient charge carrier generation. In addition, there are several other electronic and structural features that distinguish NFAs from fullerenes. My thesis focuses on understanding the interplay between the unique attributes of NFAs and the physical processes occurring in solar cells. By combining various experimental techniques with drift-diffusion simulations, the generation of free charge carriers as well as their recombination in state-of-the-art NFA-based solar cells is characterized. For this purpose, solar cells based on the donor polymer PM6 and the NFA Y6 have been investigated. The generation of free charge carriers in PM6:Y6 is efficient and independent of electric field and excitation energy. Temperature-dependent measurements show a very low activation energy for photocurrent generation (about 6 meV), indicating barrierless charge carrier separation. Theoretical modeling suggests that Y6 molecules have large quadrupole moments, leading to band bending at the donor-acceptor interface and thereby reducing the electrostatic Coulomb dissociation barrier. In this regard, this work identifies poor extraction of free charges in competition with nongeminate recombination as a dominant loss process in PM6:Y6 devices. Subsequently, the spectral characteristics of PM6:Y6 solar cells were investigated with respect to the dominant process of charge carrier recombination. It was found that the photon emission under open-circuit conditions can be almost entirely attributed to the occupation and recombination of Y6 singlet excitons. Nevertheless, the recombination pathway via the singlet state contributes only 1\% to the total recombination, which is dominated by the charge transfer state (CT-state) at the donor-acceptor interface. Further V_OC gains can therefore only be expected if the density and/or recombination rate of these CT-states can be significantly reduced. Finally, the role of energetic disorder in NFA solar cells is investigated by comparing Y6 with a structurally related derivative, named N4. Layer morphology studies combined with temperature-dependent charge transport experiments show significantly lower structural and energetic disorder in the case of the PM6:Y6 blend. For both PM6:Y6 and PM6:N4, disorder determines the maximum achievable V_OC, with PM6:Y6 benefiting from improved morphological order. Overall, the obtained findings point to avenues for the realization of NFA-based solar cells with even smaller V_OC losses. Further reduction of nongeminate recombination and energetic disorder should result in organic solar cells with efficiencies above 20\% in the future.}, language = {en} } @article{PerdigonToroZhangMarkinaetal.2020, author = {Perdigon-Toro, Lorena and Zhang, Huotian and Markina, Anastaa si and Yuan, Jun and Hosseini, Seyed Mehrdad and Wolff, Christian Michael and Zuo, Guangzheng and Stolterfoht, Martin and Zou, Yingping and Gao, Feng and Andrienko, Denis and Shoaee, Safa and Neher, Dieter}, title = {Barrierless free charge generation in the high-performance PM6:Y6 bulk heterojunction non-fullerene solar cell}, series = {Advanced materials}, volume = {32}, journal = {Advanced materials}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0935-9648}, doi = {10.1002/adma.201906763}, pages = {9}, year = {2020}, abstract = {Organic solar cells are currently experiencing a second golden age thanks to the development of novel non-fullerene acceptors (NFAs). Surprisingly, some of these blends exhibit high efficiencies despite a low energy offset at the heterojunction. Herein, free charge generation in the high-performance blend of the donor polymer PM6 with the NFA Y6 is thoroughly investigated as a function of internal field, temperature and excitation energy. Results show that photocurrent generation is essentially barrierless with near-unity efficiency, regardless of excitation energy. Efficient charge separation is maintained over a wide temperature range, down to 100 K, despite the small driving force for charge generation. Studies on a blend with a low concentration of the NFA, measurements of the energetic disorder, and theoretical modeling suggest that CT state dissociation is assisted by the electrostatic interfacial field which for Y6 is large enough to compensate the Coulomb dissociation barrier.}, language = {en} } @article{NikolisBenduhnHolzmuelleretal.2017, author = {Nikolis, Vasileios C. and Benduhn, Johannes and Holzmueller, Felix and Piersimoni, Fortunato and Lau, Matthias and Zeika, Olaf and Neher, Dieter and Koerner, Christian and Spoltore, Donato and Vandewal, Koen}, title = {Reducing Voltage Losses in Cascade Organic Solar Cells while Maintaining High External Quantum Efficiencies}, series = {dvanced energy materials}, volume = {7}, journal = {dvanced energy materials}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201700855}, pages = {122 -- 136}, year = {2017}, abstract = {High photon energy losses limit the open-circuit voltage (V-OC) and power conversion efficiency of organic solar cells (OSCs). In this work, an optimization route is presented which increases the V-OC by reducing the interfacial area between donor (D) and acceptor (A). This optimization route concerns a cascade device architecture in which the introduction of discontinuous interlayers between alpha-sexithiophene (alpha-6T) (D) and chloroboron subnaphthalocyanine (SubNc) (A) increases the V-OC of an alpha-6T/SubNc/SubPc fullerene-free cascade OSC from 0.98 V to 1.16 V. This increase of 0.18 V is attributed solely to the suppression of nonradiative recombination at the D-A interface. By accurately measuring the optical gap (E-opt) and the energy of the charge-transfer state (E-CT) of the studied OSC, a detailed analysis of the overall voltage losses is performed. E-opt - qV(OC) losses of 0.58 eV, which are among the lowest observed for OSCs, are obtained. Most importantly, for the V-OC-optimized devices, the low-energy (700 nm) external quantum efficiency (EQE) peak remains high at 79\%, despite a minimal driving force for charge separation of less than 10 meV. This work shows that low-voltage losses can be combined with a high EQE in organic photovoltaic devices.}, language = {en} } @article{LoveChouHuangetal.2016, author = {Love, John A. and Chou, Shu-Hua and Huang, Ye and Bazan, Guillermo C. and Thuc-Quyen Nguyen,}, title = {Effects of solvent additive on "s-shaped" curves in solution-processed small molecule solar cells}, series = {Beilstein journal of organic chemistry}, volume = {12}, journal = {Beilstein journal of organic chemistry}, publisher = {Beilstein-Institut zur F{\~A}\Prderung der Chemischen Wissenschaften}, address = {Frankfurt, Main}, issn = {1860-5397}, doi = {10.3762/bjoc.12.249}, pages = {2543 -- 2555}, year = {2016}, abstract = {A novel molecular chromophore, p-SIDT(FBTThCA8)(2), is introduced as an electron-donor material for bulk heterojunction (BHJ) solar cells with broad absorption and near ideal energy levels for the use in combination with common acceptor materials. It is found that films cast from chlorobenzene yield devices with strongly s-shaped current-voltage curves, drastically limiting performance. We find that addition of the common solvent additive diiodooctane, in addition to facilitating crystallization, leads to improved vertical phase separation. This yields much better performing devices, with improved curve shape, demonstrating the importance of morphology control in BHJ devices and improving the understanding of the role of solvent additives.}, language = {en} } @phdthesis{Kurpiers2019, author = {Kurpiers, Jona}, title = {Probing the pathways of free charge generation and recombination in organic solar cells}, doi = {10.25932/publishup-42909}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-429099}, school = {Universit{\"a}t Potsdam}, pages = {VI, 128, xxi}, year = {2019}, abstract = {Organic semiconductors are a promising class of materials. Their special properties are the particularly good absorption, low weight and easy processing into thin films. Therefore, intense research has been devoted to the realization of thin film organic solar cells (OPVs). Because of the low dielectric constant of organic semiconductors, primary excitations (excitons) are strongly bound and a type II heterojunction needs to be introduced to split these excitations into free charges. Therefore, most organic solar cells consist of at least an electron donor and electron acceptor material. For such donor acceptor systems mainly three states are relevant; the photoexcited exciton on the donor or acceptor material, the charge transfer state at the donor-acceptor interface and the charge separated state of a free electron and hole. The interplay between these states significantly determines the efficiency of organic solar cells. Due to the high absorption and the low charge carrier mobilities, the active layers are usually thin but also, exciton dissociation and free charge formation proceeds rapidely, which makes the study of carrier dynamics highly challenging. Therefore, the focus of this work was first to install new experimental setups for the investigation of the charge carrier dynamics in complete devices with superior sensitivity and time resolution and, second, to apply these methods to prototypical photovoltaic materials to address specific questions in the field of organic and hybrid photovoltaics. Regarding the first goal, a new setup combining transient absorption spectroscopy (TAS) and time delayed collection field (TDCF) was designed and installed in Potsdam. An important part of this work concerned the improvement of the electronic components with respect to time resolution and sensitivity. To this end, a highly sensitive amplifier for driving and detecting the device response in TDCF was developed. This system was then applied to selected organic and hybrid model systems with a particular focus on the understanding of the loss mechanisms that limit the fill factor and short circuit current of organic solar cells. The first model system was a hybrid photovoltaic material comprising inorganic quantum dots decorated with organic ligands. Measurements with TDCF revealed fast free carrier recombination, in part assisted by traps, while bias-assisted charge extraction measurements showed high mobility. The measured parameters then served as input for a successful description of the device performance with an analytical model. With a further improvement of the instrumentation, a second topic was the detailed analysis of non-geminate recombination in a disordered polymer:fullerene blend where an important question was the effect of disorder on the carrier dynamics. The measurements revealed that early time highly mobile charges undergo fast non-geminate recombination at the contacts, causing an apparent field dependence of free charge generation in TDCF experiments if not conducted properly. On the other hand, recombination the later time scale was determined by dispersive recombination in the bulk of the active layer, showing the characteristics of carrier dynamics in an exponential density of state distribution. Importantly, the comparison with steady state recombination data suggested a very weak impact of non-thermalized carriers on the recombination properties of the solar cells under application relevant illumination conditions. Finally, temperature and field dependent studies of free charge generation were performed on three donor-acceptor combinations, with two donor polymers of the same material family blended with two different fullerene acceptor molecules. These particular material combinations were chosen to analyze the influence of the energetic and morphology of the blend on the efficiency of charge generation. To this end, activation energies for photocurrent generation were accurately determined for a wide range of excitation energies. The results prove that the formation of free charge is via thermalized charge transfer states and does not involve hot exciton splitting. Surprisingly, activation energies were of the order of thermal energy at room temperature. This led to the important conclusion that organic solar cells perform well not because of predominate high energy pathways but because the thermalized CT states are weakly bound. In addition, a model is introduced to interconnect the dissociation efficiency of the charge transfer state with its recombination observable with photoluminescence, which rules out a previously proposed two-pool model for free charge formation and recombination. Finally, based on the results, proposals for the further development of organic solar cells are formulated.}, language = {en} } @phdthesis{Kniepert2015, author = {Kniepert, Juliane}, title = {Correlation between dynamic parameters and device performance of organic solar cells}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-90087}, school = {Universit{\"a}t Potsdam}, pages = {129}, year = {2015}, abstract = {Organic bulk heterojunction (BHJ) solar cells based on polymer:fullerene blends are a promising alternative for a low-cost solar energy conversion. Despite significant improvements of the power conversion efficiency in recent years, the fundamental working principles of these devices are yet not fully understood. In general, the current output of organic solar cells is determined by the generation of free charge carriers upon light absorption and their transport to the electrodes in competition to the loss of charge carriers due to recombination. The object of this thesis is to provide a comprehensive understanding of the dynamic processes and physical parameters determining the performance. A new approach for analyzing the characteristic current-voltage output was developed comprising the experimental determination of the efficiencies of charge carrier generation, recombination and transport, combined with numerical device simulations. Central issues at the beginning of this work were the influence of an electric field on the free carrier generation process and the contribution of generation, recombination and transport to the current-voltage characteristics. An elegant way to directly measure the field dependence of the free carrier generation is the Time Delayed Collection Field (TDCF) method. In TDCF charge carriers are generated by a short laser pulse and subsequently extracted by a defined rectangular voltage pulse. A new setup was established with an improved time resolution compared to former reports in literature. It was found that charge generation is in general independent of the electric field, in contrast to the current view in literature and opposed to the expectations of the Braun-Onsager model that was commonly used to describe the charge generation process. Even in cases where the charge generation was found to be field-dependend, numerical modelling showed that this field-dependence is in general not capable to account for the voltage dependence of the photocurrent. This highlights the importance of efficient charge extraction in competition to non-geminate recombination, which is the second objective of the thesis. Therefore, two different techniques were combined to characterize the dynamics and efficiency of non-geminate recombination under device-relevant conditions. One new approach is to perform TDCF measurements with increasing delay between generation and extraction of charges. Thus, TDCF was used for the first time to measure charge carrier generation, recombination and transport with the same experimental setup. This excludes experimental errors due to different measurement and preparation conditions and demonstrates the strength of this technique. An analytic model for the description of TDCF transients was developed and revealed the experimental conditions for which reliable results can be obtained. In particular, it turned out that the \$RC\$ time of the setup which is mainly given by the sample geometry has a significant influence on the shape of the transients which has to be considered for correct data analysis. Secondly, a complementary method was applied to characterize charge carrier recombination under steady state bias and illumination, i.e. under realistic operating conditions. This approach relies on the precise determination of the steady state carrier densities established in the active layer. It turned out that current techniques were not sufficient to measure carrier densities with the necessary accuracy. Therefore, a new technique {Bias Assisted Charge Extraction} (BACE) was developed. Here, the charge carriers photogenerated under steady state illumination are extracted by applying a high reverse bias. The accelerated extraction compared to conventional charge extraction minimizes losses through non-geminate recombination and trapping during extraction. By performing numerical device simulations under steady state, conditions were established under which quantitative information on the dynamics can be retrieved from BACE measurements. The applied experimental techniques allowed to sensitively analyse and quantify geminate and non-geminate recombination losses along with charge transport in organic solar cells. A full analysis was exemplarily demonstrated for two prominent polymer-fullerene blends. The model system P3HT:PCBM spincast from chloroform (as prepared) exhibits poor power conversion efficiencies (PCE) on the order of 0.5\%, mainly caused by low fill factors (FF) and currents. It could be shown that the performance of these devices is limited by the hole transport and large bimolecular recombination (BMR) losses, while geminate recombination losses are insignificant. The low polymer crystallinity and poor interconnection between the polymer and fullerene domains leads to a hole mobility of the order of 10^-7 cm^2/Vs which is several orders of magnitude lower than the electron mobility in these devices. The concomitant build up of space charge hinders extraction of both electrons and holes and promotes bimolecular recombination losses. Thermal annealing of P3HT:PCBM blends directly after spin coating improves crystallinity and interconnection of the polymer and the fullerene phase and results in comparatively high electron and hole mobilities in the order of 10^-3 cm^2/Vs and 10^-4 cm^2/Vs, respectively. In addition, a coarsening of the domain sizes leads to a reduction of the BMR by one order of magnitude. High charge carrier mobilities and low recombination losses result in comparatively high FF (>65\%) and short circuit current (J_SC ≈ 10 mA/cm^2). The overall device performance (PCE ≈ 4\%) is only limited by a rather low spectral overlap of absorption and solar emission and a small V_OC, given by the energetics of the P3HT. From this point of view the combination of the low bandgap polymer PTB7 with PCBM is a promising approach. In BHJ solar cells, this polymer leads to a higher V_OC due to optimized energetics with PCBM. However, the J_SC in these (unoptimized) devices is similar to the J_SC in the optimized blend with P3HT and the FF is rather low (≈ 50\%). It turned out that the unoptimized PTB7:PCBM blends suffer from high BMR, a low electron mobility of the order of 10^-5 cm^2/Vs and geminate recombination losses due to field dependent charge carrier generation. The use of the solvent additive DIO optimizes the blend morphology, mainly by suppressing the formation of very large fullerene domains and by forming a more uniform structure of well interconnected donor and acceptor domains of the order of a few nanometers. Our analysis shows that this results in an increase of the electron mobility by about one order of magnitude (3 x 10^-4 cm^2/Vs), while BMR and geminate recombination losses are significantly reduced. In total these effects improve the J_SC (≈ 17 mA/cm^2) and the FF (> 70\%). In 2012 this polymer/fullerene combination resulted in a record PCE for a single junction OSC of 9.2\%. Remarkably, the numerical device simulations revealed that the specific shape of the J-V characteristics depends very sensitively to the variation of not only one, but all dynamic parameters. On the one hand this proves that the experimentally determined parameters, if leading to a good match between simulated and measured J-V curves, are realistic and reliable. On the other hand it also emphasizes the importance to consider all involved dynamic quantities, namely charge carrier generation, geminate and non-geminate recombination as well as electron and hole mobilities. The measurement or investigation of only a subset of these parameters as frequently found in literature will lead to an incomplete picture and possibly to misleading conclusions. Importantly, the comparison of the numerical device simulation employing the measured parameters and the experimental \$J-V\$ characteristics allows to identify loss channels and limitations of OSC. For example, it turned out that inefficient extraction of charge carriers is a criticical limitation factor that is often disobeyed. However, efficient and fast transport of charges becomes more and more important with the development of new low bandgap materials with very high internal quantum efficiencies. Likewise, due to moderate charge carrier mobilities, the active layer thicknesses of current high-performance devices are usually limited to around 100 nm. However, larger layer thicknesses would be more favourable with respect to higher current output and robustness of production. Newly designed donor materials should therefore at best show a high tendency to form crystalline structures, as observed in P3HT, combined with the optimized energetics and quantum efficiency of, for example, PTB7.}, language = {en} } @article{FoertigKniepertGlueckeretal.2014, author = {Foertig, Alexander and Kniepert, Juliane and Gluecker, Markus and Brenner, Thomas J. K. and Dyakonov, Vladimir and Neher, Dieter and Deibel, Carsten}, title = {Nongeminate and geminate recombination in PTB7: PCBM solar cells}, series = {Advanced functional materials}, volume = {24}, journal = {Advanced functional materials}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1616-301X}, doi = {10.1002/adfm.201302134}, pages = {1306 -- 1311}, year = {2014}, language = {en} } @article{BenduhnPiersimoniLondietal.2018, author = {Benduhn, Johannes and Piersimoni, Fortunato and Londi, Giacomo and Kirch, Anton and Widmer, Johannes and Koerner, Christian and Beljonne, David and Neher, Dieter and Spoltore, Donato and Vandewal, Koen}, title = {Impact of triplet excited states on the open-circuit voltage of organic solar cells}, series = {dvanced energy materials}, volume = {8}, journal = {dvanced energy materials}, number = {21}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201800451}, pages = {7}, year = {2018}, abstract = {The best organic solar cells (OSCs) achieve comparable peak external quantum efficiencies and fill factors as conventional photovoltaic devices. However, their voltage losses are much higher, in particular those due to nonradiative recombination. To investigate the possible role of triplet states on the donor or acceptor materials in this process, model systems comprising Zn- and Cu-phthalocyanine (Pc), as well as fluorinated versions of these donors, combined with C-60 as acceptor are studied. Fluorination allows tuning the energy level alignment between the lowest energy triplet state (T-1) and the charge-transfer (CT) state, while the replacement of Zn by Cu as the central metal in the Pcs leads to a largely enhanced spin-orbit coupling. Only in the latter case, a substantial influence of the triplet state on the nonradiative voltage losses is observed. In contrast, it is found that for a large series of typical OSC materials, the relative energy level alignment between T-1 and the CT state does not substantially affect nonradiative voltage losses.}, language = {en} } @article{ArminChenJinetal.2018, author = {Armin, Ardalan and Chen, Zhiming and Jin, Yaocheng and Zhang, Kai and Huang, Fei and Shoaee, Safa}, title = {A Shockley-Type polymer}, series = {Advanced energy materials}, volume = {8}, journal = {Advanced energy materials}, number = {7}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201701450}, pages = {9}, year = {2018}, abstract = {Charge extraction rate in solar cells made of blends of electron donating/accepting organic semiconductors is typically slow due to their low charge carrier mobility. This sets a limit on the active layer thickness and has hindered the industrialization of organic solar cells (OSCs). Herein, charge transport and recombination properties of an efficient polymer (NT812):fullerene blend are investigated. This system delivers power conversion efficiency of >9\% even when the junction thickness is as large as 800 nm. Experimental results indicate that this material system exhibits exceptionally low bimolecular recombination constant, 800 times smaller than the diffusion-controlled electron and hole encounter rate. Comparing theoretical results based on a recently introduced modified Shockley model for fill factor, and experiments, clarifies that charge collection is nearly ideal in these solar cells even when the thickness is several hundreds of nanometer. This is the first realization of high-efficiency Shockley-type organic solar cells with junction thicknesses suitable for scaling up.}, language = {en} } @article{AlqahtaniBabicsGorenflotetal.2018, author = {Alqahtani, Obaid and Babics, Maxime and Gorenflot, Julien and Savikhin, Victoria and Ferron, Thomas and Balawi, Ahmed H. and Paulke, Andreas and Kan, Zhipeng and Pope, Michael and Clulow, Andrew J. and Wolf, Jannic and Burn, Paul L. and Gentle, Ian R. and Neher, Dieter and Toney, Michael F. and Laquai, Frederic and Beaujuge, Pierre M. and Collins, Brian A.}, title = {Mixed Domains Enhance Charge Generation and Extraction in Bulk-Heterojunction Solar Cells with Small-Molecule Donors}, series = {Advanced energy materials}, volume = {8}, journal = {Advanced energy materials}, number = {19}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1614-6832}, doi = {10.1002/aenm.201702941}, pages = {16}, year = {2018}, abstract = {The interplay between nanomorphology and efficiency of polymer-fullerene bulk-heterojunction (BHJ) solar cells has been the subject of intense research, but the generality of these concepts for small-molecule (SM) BHJs remains unclear. Here, the relation between performance; charge generation, recombination, and extraction dynamics; and nanomorphology achievable with two SM donors benzo[1,2-b:4,5-b]dithiophene-pyrido[3,4-b]-pyrazine BDT(PPTh2)(2), namely SM1 and SM2, differing by their side-chains, are examined as a function of solution additive composition. The results show that the additive 1,8-diiodooctane acts as a plasticizer in the blends, increases domain size, and promotes ordering/crystallinity. Surprisingly, the system with high domain purity (SM1) exhibits both poor exciton harvesting and severe charge trapping, alleviated only slightly with increased crystallinity. In contrast, the system consisting of mixed domains and lower crystallinity (SM2) shows both excellent exciton harvesting and low charge recombination losses. Importantly, the onset of large, pure crystallites in the latter (SM2) system reduces efficiency, pointing to possible differences in the ideal morphologies for SM-based BHJ solar cells compared with polymer-fullerene devices. In polymer-based systems, tie chains between pure polymer crystals establish a continuous charge transport network, whereas SM-based active layers may in some cases require mixed domains that enable both aggregation and charge percolation to the electrodes.}, language = {en} } @article{AlbrechtVandewalTumblestonetal.2014, author = {Albrecht, Steve and Vandewal, Koen and Tumbleston, John R. and Fischer, Florian S. U. and Douglas, Jessica D. and Frechet, Jean M. J. and Ludwigs, Sabine and Ade, Harald W. and Salleo, Alberto and Neher, Dieter}, title = {On the efficiency of charge transfer state splitting in polymer: Fullerene solar cells}, series = {Advanced materials}, volume = {26}, journal = {Advanced materials}, number = {16}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0935-9648}, doi = {10.1002/adma.201305283}, pages = {2533 -- 2539}, year = {2014}, language = {en} } @phdthesis{Albrecht2014, author = {Albrecht, Steve}, title = {Generation, recombination and extraction of charges in polymer}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-72285}, school = {Universit{\"a}t Potsdam}, pages = {144}, year = {2014}, abstract = {A dramatic efficiency improvement of bulk heterojunction solar cells based on electron-donating conjugated polymers in combination with soluble fullerene derivatives has been achieved over the past years. Certified and reported power conversion efficiencies now reach over 9\% for single junctions and exceed the 10\% benchmark for tandem solar cells. This trend brightens the vision of organic photovoltaics becoming competitive with inorganic solar cells including the realization of low-cost and large-area organic photovoltaics. For the best performing organic materials systems, the yield of charge generation can be very efficient. However, a detailed understanding of the free charge carrier generation mechanisms at the donor acceptor interface and the energy loss associated with it needs to be established. Moreover, organic solar cells are limited by the competition between charge extraction and free charge recombination, accounting for further efficiency losses. A conclusive picture and the development of precise methodologies for investigating the fundamental processes in organic solar cells are crucial for future material design, efficiency optimization, and the implementation of organic solar cells into commercial products. In order to advance the development of organic photovoltaics, my thesis focuses on the comprehensive understanding of charge generation, recombination and extraction in organic bulk heterojunction solar cells summarized in 6 chapters on the cumulative basis of 7 individual publications. The general motivation guiding this work was the realization of an efficient hybrid inorganic/organic tandem solar cell with sub-cells made from amorphous hydrogenated silicon and organic bulk heterojunctions. To realize this project aim, the focus was directed to the low band-gap copolymer PCPDTBT and its derivatives, resulting in the examination of the charge carrier dynamics in PCPDTBT:PC70BM blends in relation to by the blend morphology. The phase separation in this blend can be controlled by the processing additive diiodooctane, enhancing domain purity and size. The quantitative investigation of the free charge formation was realized by utilizing and improving the time delayed collection field technique. Interestingly, a pronounced field dependence of the free carrier generation for all blends is found, with the field dependence being stronger without the additive. Also, the bimolecular recombination coefficient for both blends is rather high and increases with decreasing internal field which we suggest to be caused by a negative field dependence of mobility. The additive speeds up charge extraction which is rationalized by the threefold increase in mobility. By fluorine attachment within the electron deficient subunit of PCPDTBT, a new polymer F-PCPDTBT is designed. This new material is characterized by a stronger tendency to aggregate as compared to non-fluorinated PCPDTBT. Our measurements show that for F-PCPDTBT:PCBM blends the charge carrier generation becomes more efficient and the field-dependence of free charge carrier generation is weakened. The stronger tendency to aggregate induced by the fluorination also leads to increased polymer rich domains, accompanied in a threefold reduction in the non-geminate recombination coefficient at conditions of open circuit. The size of the polymer domains is nicely correlated to the field-dependence of charge generation and the Langevin reduction factor, which highlights the importance of the domain size and domain purity for efficient charge carrier generation. In total, fluorination of PCPDTBT causes the PCE to increase from 3.6 to 6.1\% due to enhanced fill factor, short circuit current and open circuit voltage. Further optimization of the blend ratio, active layer thickness, and polymer molecular weight resulted in 6.6\% efficiency for F-PCPDTBT:PC70BM solar cells. Interestingly, the double fluorinated version 2F-PCPDTBT exhibited poorer FF despite a further reduction of geminate and non-geminate recombination losses. To further analyze this finding, a new technique is developed that measures the effective extraction mobility under charge carrier densities and electrical fields comparable to solar cell operation conditions. This method involves the bias enhanced charge extraction technique. With the knowledge of the carrier density under different electrical field and illumination conditions, a conclusive picture of the changes in charge carrier dynamics leading to differences in the fill factor upon fluorination of PCPDTBT is attained. The more efficient charge generation and reduced recombination with fluorination is counterbalanced by a decreased extraction mobility. Thus, the highest fill factor of 60\% and efficiency of 6.6\% is reached for F-PCPDTBT blends, while 2F-PCPDTBT blends have only moderate fill factors of 54\% caused by the lower effective extraction mobility, limiting the efficiency to 6.5\%. To understand the details of the charge generation mechanism and the related losses, we evaluated the yield and field-dependence of free charge generation using time delayed collection field in combination with sensitive measurements of the external quantum efficiency and absorption coefficients for a variety of blends. Importantly, both the yield and field-dependence of free charge generation is found to be unaffected by excitation energy, including direct charge transfer excitation below the optical band gap. To access the non-detectable absorption at energies of the relaxed charge transfer emission, the absorption was reconstructed from the CT emission, induced via the recombination of thermalized charges in electroluminescence. For a variety of blends, the quantum yield at energies of charge transfer emission was identical to excitations with energies well above the optical band-gap. Thus, the generation proceeds via the split-up of the thermalized charge transfer states in working solar cells. Further measurements were conducted on blends with fine-tuned energy levels and similar blend morphologies by using different fullerene derivatives. A direct correlation between the efficiency of free carrier generation and the energy difference of the relaxed charge transfer state relative to the energy of the charge separated state is found. These findings open up new guidelines for future material design as new high efficiency materials require a minimum energetic offset between charge transfer and the charge separated state while keeping the HOMO level (and LUMO level) difference between donor and acceptor as small as possible.}, language = {en} }