@article{SerranoMunozFernandezSerranoSaliwanNeumannetal.2022, author = {Serrano-Munoz, Itziar and Fern{\´a}ndez Serrano, Ricardo and Saliwan-Neumann, Romeo and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Dislocation substructures in pure aluminium after creep deformation as studied by electron backscatter diffraction}, series = {Journal of applied crystallography / International Union of Crystallography}, volume = {55}, journal = {Journal of applied crystallography / International Union of Crystallography}, publisher = {Munksgaard}, address = {Copenhagen}, issn = {1600-5767}, doi = {10.1107/S1600576722005209}, pages = {860 -- 869}, year = {2022}, abstract = {In the present work, electron backscatter diffraction was used to determine the microscopic dislocation structures generated during creep (with tests interrupted at the steady state) in pure 99.8\% aluminium. This material was investigated at two different stress levels, corresponding to the power-law and power-law breakdown regimes. The results show that the formation of subgrain cellular structures occurs independently of the crystallographic orientation. However, the density of these cellular structures strongly depends on the grain crystallographic orientation with respect to the tensile axis direction, with (111) grains exhibiting the highest densities at both stress levels. It is proposed that this behaviour is due to the influence of intergranular stresses, which is different in (111) and (001) grains.}, language = {en} } @misc{MuellerKupschLaquaietal.2018, author = {M{\"u}ller, Bernd Randolf and Kupsch, Andreas and Laquai, Rene and Nellesen, Jens and Tillmann, Wolfgang and Kasperovich, Galina and Bruno, Giovanni}, title = {Microstructure Characterisation of Advanced Materials via 2D and 3D X-Ray Refraction Techniques}, series = {Materials Science Forum}, volume = {941}, journal = {Materials Science Forum}, publisher = {Trans Tech Publications Ltd}, address = {Zurich}, isbn = {978-3-0357-1208-7}, issn = {0255-5476}, doi = {10.4028/www.scientific.net/MSF.941.2401}, pages = {2401 -- 2406}, year = {2018}, abstract = {3D imaging techniques have an enormous potential to understand the microstructure, its evolution, and its link to mechanical, thermal, and transport properties. In this conference paper we report the use of a powerful, yet not so wide-spread, set of X-ray techniques based on refraction effects. X-ray refraction allows determining internal specific surface (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with a nanometric detectability. We demonstrate showcases of ceramics and composite materials, where microstructural parameters could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. We present in situ analysis of the damage evolution in an Al/Al2O3 metal matrix composite during tensile load and the identification of void formation (different kinds of defects, particularly unsintered powder hidden in pores, and small inhomogeneity's like cracks) in Ti64 parts produced by selective laser melting using synchrotron X-ray refraction radiography and tomography.}, language = {en} } @article{FernandezGonzalezDoncelGarcesetal.2020, author = {Fernandez, Ricardo and Gonzalez-Doncel, Gaspar and Garces, Gerardo and Bruno, Giovanni}, title = {Towards a comprehensive understanding of creep}, series = {Materials science \& engineering. A, Structural materials: properties, microstructure and processing}, volume = {776}, journal = {Materials science \& engineering. A, Structural materials: properties, microstructure and processing}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2020.139036}, pages = {7}, year = {2020}, abstract = {We show that the equation proposed by Takeuchi and Argon to explain the creep behavior of Al-Mg solid solution can be used to describe also the creep behavior of pure aluminum. In this frame, it is possible to avoid the use of the classic pre-exponential fitting parameter in the power law equation to predict the minimum creep strain rate. The effect of the fractal arrangement of dislocations, developed at the mesoscale, must be considered to fully explain the experimental data. These ideas allow improving the recently introduced SSTC model, fully describing the primary and secondary creep regimes of aluminum alloys without the need for fitting. Creep data from commercially pure A199.8\% and Al-Mg alloys tested at different temperatures and stresses are used to validate the proposed ideas.}, language = {en} } @article{CabezaMuellerPereyraetal.2018, author = {Cabeza, Sandra and M{\"u}ller, Bernd R. and Pereyra, Ricio and Fernandez, Ricardo and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Evidence of damage evolution during creep of Al-Mg alloy using synchrotron X-ray refraction}, series = {Journal of applied crystallography}, volume = {51}, journal = {Journal of applied crystallography}, publisher = {International Union of Crystallography}, address = {Chester}, issn = {1600-5767}, doi = {10.1107/S1600576718001449}, pages = {420 -- 427}, year = {2018}, abstract = {In order to provide further evidence of damage mechanisms predicted by the recent solid-state transformation creep (SSTC) model, direct observation of damage accumulation during creep of Al-3.85Mg was made using synchrotron X-ray refraction. X-ray refraction techniques detect the internal specific surface (i.e. surface per unit volume) on a length scale comparable to the specimen size, but with microscopic sensitivity. A significant rise in the internal specific surface with increasing creep time was observed, providing evidence for the creation of a fine grain substructure, as predicted by the SSTC model. This substructure was also observed by scanning electron microscopy.}, language = {en} }