@article{ZenSaphiannikovaNeheretal.2006, author = {Zen, Achmad and Saphiannikova, Marina and Neher, Dieter and Grenzer, J{\"o}rg and Grigorian, Souren A. and Pietsch, Ullrich and Asawapirom, Udom and Janietz, Silvia and Scherf, Ullrich and Lieberwirth, Ingo and Wegner, Gerhard}, title = {Effect of molecular weight on the structure and crystallinity of poly(3-hexylthiophene)}, doi = {10.1021/Ma0521349}, year = {2006}, abstract = {Recently, two different groups have reported independently that the mobility of field-effect transistors made from regioregular poly(3-hexylthiophene) (P3HT) increases strongly with molecular weight. Two different models were presented: one proposing carrier trapping at grain boundaries and the second putting emphasis on the conformation and packing of the polymer chains in the thin layers for different molecular weights. Here, we present the results of detailed investigations of powders and thin films of deuterated P3HT fractions with different molecular weight. For powder samples, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and X-ray diffraction (XRD) were used to investigate the structure and crystallization behavior of the polymers. The GPC investigations show that all weight fractions possess a rather broad molecular weight distribution. DSC measurements reveal a strong decrease of the crystallization temperature and, most important, a significant decrease of the degree of crystallinity with decreasing molecular weight. To study the structure of thin layers in lateral and vertical directions, both transmission electron microscopy (TEM) and X-ray grazing incidence diffraction (GID) were utilized. These methods show that thin layers of the low molecular weight fraction consist of well-defined crystalline domains embedded in a disordered matrix. We propose that the transport properties of layers prepared from fractions of poly(3-hexylthiophene) with different molecular weight are largely determined by the crystallinity of the samples and not by the perfection of the packing of the chains in the individual crystallites}, language = {en} } @article{ZenSaphiannikovaNeheretal.2005, author = {Zen, Achmad and Saphiannikova, Marina and Neher, Dieter and Asawapirom, Udom and Scherf, Ullrich}, title = {Comparative study of the field-effect mobility of a copolymer and a binary blend based on poly(3- alkylthiophene)s}, issn = {0897-4756}, year = {2005}, abstract = {The performance of highly soluble regioregular poly[ (3-hexylthiophene)-co-(3-octylthiophetie)] (P3HTOT) as a semiconducting material in organic field-effect transistors (OFETs) is presented in comparison to that of the corresponding homopolymers. Transistors made from as-prepared layers of P3HTOT exhibit a mobility of ca. 7 x 10(-3) cm(2) V-1 s(-1), which is comparable to the performance of transistors made from as-prepared poly(3-hexylthiophene) (P3HT) and almost 6 times larger than the mobility of transistors prepared with poly(3-octylthiophene) (P3OT). On the other hand, the solubility parameter delta(p) of P3HTOT is close to that of the highly soluble P3OT. Moreover, compared to a physical blend of poly(3-hexylthiophene) and poly(3-octylthiophene), the mobility of P3HTOT devices is almost twice as large and the performance does not degrade upon annealing at elevated temperatures. Therefore, the copolymer approach outlined here may be one promising step toward an optimum balance between a Sufficient processability of the polymers from common organic solvents, a high solid state order, and applicable OFET performances}, language = {en} } @article{YadavalliSaphiannikovaSanter2014, author = {Yadavalli, Nataraja Sekhar and Saphiannikova, Marina and Santer, Svetlana}, title = {Photosensitive response of azobenzene containing films towards pure intensity or polarization interference patterns}, series = {Applied physics letters}, volume = {105}, journal = {Applied physics letters}, number = {5}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0003-6951}, doi = {10.1063/1.4891615}, pages = {5}, year = {2014}, abstract = {In this paper, we report on differences in the response of photosensitive azobenzene containing films upon irradiation with the intensity or polarization interference patterns. Two materials are studied differing in the molecular weight: an azobenzene-containing polymer and a molecular glass formed from a much smaller molecule consisting of three connected azobenzene units. Topography changes occurring along with the changes in irradiation conditions are recorded using a homemade set-up combining an optical part for generation and shaping of interference patterns and an atomic force microscope for acquiring the kinetics of film deformation. In this way, we could reveal the unique behavior of photosensitive materials during the first few minutes of irradiation: the change in topography is initially driven by an increase in the azobenzene free volume along with the transcis isomerization, followed by the mass transport finally resulting in the surface relief grating. This study demonstrates the great potential of our setup to experimentally highlight puzzling processes governing the formation of surface relief gratings. (C) 2014 AIP Publishing LLC.}, language = {en} } @article{YadavalliSaphiannikovaLomadzeetal.2013, author = {Yadavalli, Nataraja Sekhar and Saphiannikova, Marina and Lomadze, Nino and Goldenberg, Leonid M. and Santer, Svetlana}, title = {Structuring of photosensitive material below diffraction limit using far field irradiation}, series = {Applied physics : A, Materials science \& processing}, volume = {113}, journal = {Applied physics : A, Materials science \& processing}, number = {2}, publisher = {Springer}, address = {New York}, issn = {0947-8396}, doi = {10.1007/s00339-013-7945-3}, pages = {263 -- 272}, year = {2013}, abstract = {In this paper, we report on in-situ atomic force microscopy (AFM) studies of topographical changes in azobenzene-containing photosensitive polymer films that are irradiated with light interference patterns. We have developed an experimental setup consisting of an AFM combined with two-beam interferometry that permits us to switch between different polarization states of the two interfering beams while scanning the illuminated area of the polymer film, acquiring corresponding changes in topography in-situ. This way, we are able to analyze how the change in topography is related to the variation of the electrical field vector within the interference pattern. It is for the first time that with a rather simple experimental approach a rigorous assignment can be achieved. By performing in-situ measurements we found that for a certain polarization combination of two interfering beams [namely for the SP (a dagger center dot, a dagger") polarization pattern] the topography forms surface relief grating with only half the period of the interference patterns. Exploiting this phenomenon we are able to fabricate surface relief structures with characteristic features measuring only 140 nm, by using far field optics with a wavelength of 491 nm. We believe that this relatively simple method could be extremely valuable to, for instance, produce structural features below the diffraction limit at high-throughput, and this could significantly contribute to the search of new fabrication strategies in electronics and photonics industry.}, language = {en} } @article{StillerKarageorgievGeueetal.2004, author = {Stiller, Burkhard and Karageorgiev, Peter and Geue, Thomas and Morawetz, Knut and Saphiannikova, Marina and Mechau, Norman and Neher, Dieter}, title = {Optically induced mass transport studied by scanning near-field optical- and atomic force microscopy}, issn = {0204-3467}, year = {2004}, abstract = {Some functionalised thin organic films show a very unusual property, namely the light induced material transport. This effect enables to generate three-dimensional structures on surfaces of azobenzene containing films only caused by special optical excitation. The physical mechanisms underlying this phenomenon have not yet been fully understood, and in addition, the dimensions of structures created in that way are macroscopic because of the optical techniques and the wavelength of the used light. In order to gain deeper insight into the physical fundamentals of this phenomenon and to open possibilities for applications it is necessary to create and study structures not only in a macroscopic but also in nanometer range. We first report about experiments to generate optically induced nano structures even down to 100 nm size. The optical stimulation was therefore made by a Scanning Near-field Optical Microscope (SNOM). Secondly, physical conditions inside optically generated surface relief gratings were studied by measuring mechanical properties with high lateral resolution via pulse force mode and force distance curves of an AFM}, language = {en} } @article{StillerGeueMorawetzetal.2005, author = {Stiller, Burkhard and Geue, Thomas and Morawetz, Knut and Saphiannikova, Marina}, title = {Optical patterning in azobenzene polymer films}, issn = {0022-2720}, year = {2005}, abstract = {Thin azobenzene polymer films show a very unusual property, namely optically induced material transport. The underlying physics for this phenomenon has not yet been thoroughly explained. Nevertheless, this effect enables one to inscribe different patterns onto film surfaces, including one- and two-dimensional periodic structures. Typical sizes of such structures are of the order of micrometers, i.e. related to the interference pattern made by the laser used for optical excitation. In this study we have measured the mechanical properties of one- and two-dimensional gratings, with a high lateral resolution, using force-distance curves and pulse force mode of the atomic force microscope. We also report on the generation of considerably finer structures, with a typical size of 100 nm, which were inscribed onto the polymer surface by the tip of a scanning near-field optical microscope used as an optical pen. Such inscription not only opens new application possibilities but also gives deeper insight into the fundamentals physics underlying optically induced material transport}, language = {en} } @article{SaphiannikovaNeher2005, author = {Saphiannikova, Marina and Neher, Dieter}, title = {Thermodynamic theory of light-induced material transport in amorphous azobenzene polymer films}, issn = {1520-6106}, year = {2005}, abstract = {It was discovered 10 years ago that the exposure of an initially flat layer of an azobenzene-containing polymer to an inhomogeneous light pattern leads to the formation of surface relief structures, accompanied by a mass transport over several micrometers. However, the driving force of this process is still unclear. We propose a new thermodynamic approach that explains a number of experimental findings including the light-induced deformation of free-standing films and the formation of surface relief gratings for main inscription geometries. Our basic assumption is that under homogeneous illumination, an initially isotropic sample should stretch itself along the polarization direction to compensate the entropy decrease produced by the photoinduced reorientation of azobenzene chromophores. The magnitude of the elastic stress, estimated by taking the derivative of the free energy over the sample deformation, is shown to be sufficient to induce plastic deformation of the polymer film. Orientational distributions of chromophores predicted by our model are compared with those deduced from Raman intensity measurements}, language = {en} } @article{SaphiannikovaHennebergGeneetal.2004, author = {Saphiannikova, Marina and Henneberg, Oliver and Gene, T. M. and Pietsch, Ullrich and Rochon, Paul}, title = {Nonlinear effects during inscription of azobenzene surface relief gratings}, issn = {1520-6106}, year = {2004}, abstract = {Surface relief gratings were inscribed on azobenzene polymer films using a pulselike exposure of an Ar+ laser. The inscription process was initiated by a sequence of short pulses followed by much longer relaxation pauses. The development of the surface relief grating was probed by a He-Ne laser measuring the scattering intensity of the first- order grating peak. The growth time of the surface relief grating was found to be larger than the length of the pulses used. This unusual behavior can be considered as a nonlinear material response associated with the trans-cis isomerization of azobenzene moieties. In this study the polymer stress was assumed to be proportional to the number of cis-isomers. One-dimensional viscoelastic analysis was used to derive the polymer deformation. The rate of trans-cis isomerization increases with the intensity of the inscribing light; in the dark it is equal to the rate of thermal cis- trans isomerization. The respective relaxation times were estimated by fitting theoretical deformation curves to experimental data}, language = {en} } @article{SaphiannikovaGeueHennebergetal.2004, author = {Saphiannikova, Marina and Geue, Thomas and Henneberg, Oliver and Morawetz, Knut and Pietsch, Ullrich}, title = {Linear viscoelastic analysis of formation and relaxation of azobenzene polymer gratings}, doi = {10.1063/1.1642606}, year = {2004}, abstract = {Surface relief gratings on azobenzene containing polymer films were prepared under irradiation by actinic light. Finite element modeling of the inscription process was carried out using linear viscoelastic analysis. It was assumed that under illumination the polymer film undergoes considerable plastification, which reduces its original Young's modulus by at least three orders of magnitude. Force densities of about 10(11) N/m(3) were necessary to reproduce the growth of the surface relief grating. It was shown that at large deformations the force of surface tension becomes comparable to the inscription force and therefore plays an essential role in the retardation of the inscription process. In addition to surface profiling the gradual development of an accompanying density grating was predicted for the regime of continuous exposure. Surface grating development under pulselike exposure cannot be explained in the frame of an incompressible fluid model. However, it was easily reproduced using the viscoelastic model with finite compressibility. (C) 2004 American Institute of Physics}, language = {en} } @article{PietschSaphiannikovaHennebergetal.2004, author = {Pietsch, Ullrich and Saphiannikova, Marina and Henneberg, Oliver and Geue, Thomas}, title = {Non-linear effects during inscription of azobenzene surface relief gratings}, year = {2004}, language = {en} } @article{PietschGeueHennebergetal.2003, author = {Pietsch, Ullrich and Geue, Thomas and Henneberg, Oliver and Saphiannikova, Marina}, title = {X-ray investigations of formation efficiency of buried azobenzene polymer density gratings}, doi = {10.1063/1.1554753}, year = {2003}, language = {en} } @article{MechauSaphiannikovaNeher2006, author = {Mechau, Norman and Saphiannikova, Marina and Neher, Dieter}, title = {Molecular tracer diffusion in thin azobenzene polymer layers}, series = {Applied physics letters}, volume = {89}, journal = {Applied physics letters}, number = {25}, publisher = {Elsevier}, address = {Melville}, issn = {0003-6951}, doi = {10.1063/1.2405853}, pages = {3}, year = {2006}, abstract = {Translational diffusion of fluorescent tracer molecules in azobenzene polymer layers is studied at different temperatures and under illumination using the method of fluorescence recovery after photobleaching. Diffusion is clearly observed in the dark above the glass transition temperature, while homogeneous illumination at 488 nm and 100 mW/cm(2) does not cause any detectable diffusion of the dye molecules within azobenzene layers. This implies that the viscosity of azobenzene layers remains nearly unchanged under illumination with visible light in the absence of internal or external forces. (c) 2006 American Institute of Physics.}, language = {en} } @article{MechauSaphiannikovaNeher2005, author = {Mechau, Norman and Saphiannikova, Marina and Neher, Dieter}, title = {Dielectric and mechanical properties of azobenzene polymer layers under visible and ultraviolet irradiation}, issn = {0024-9297}, year = {2005}, abstract = {Photoinduced changes in the mechanical and dielectric properties of azobenzene polymer films were measured utilizing the method of electromechanical spectroscopy. The measurements revealed a strong correlation between the time- dependent behavior of the plate compliance and the dielectric constant under irradiation. Actinic light causes a light softening of the film that also manifests itself in the increase of the dielectric constant, whereas ultraviolet irradiation results in an initial plasticization of the film followed by its hardening. The latter is accompanied by decrease of the dielectric constant. A semiquantitative model based on the kinetics of the photoisomerization process in azobenzene polymers is proposed. We assume that both visible and ultraviolet irradiation increase the free volume in the layer due to photoisomerization. Additionally, ultraviolet light increases the modulus of the polymer matrix due to the presence of a high density of azobenzene moieties in the cis state. These assumptions allowed us to reproduce the time- dependent behavior of the bulk compliance as well as the dielectric constant at different irradiation intensities, for both visible and ultraviolet light, with only two adjustable parameters}, language = {en} } @article{LoebnerYadavLomadzeetal.2022, author = {Loebner, Sarah and Yadav, Bharti and Lomadze, Nino and Tverdokhleb, Nina and Donner, Hendrik and Saphiannikova, Marina and Santer, Svetlana}, title = {Local direction of optomechanical stress in azobenzene containing polymers during surface relief grating formation}, series = {Macromolecular materials and engineering}, volume = {307}, journal = {Macromolecular materials and engineering}, number = {8}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1438-7492}, doi = {10.1002/mame.202100990}, pages = {10}, year = {2022}, abstract = {In this work, it is revealed how the photoinduced deformation of azobenzene containing polymers relates to the local direction of optomechanical stresses generated during irradiation with interference patterns (IPs). It can be substantiated by the modeling approach proposed by Saphiannikova et al., which describes the directional photodeformations in glassy side-chain azobenzene polymers, and proves that these deformations arise from the reorientation of rigid backbone segments along the light polarization direction. In experiments and modeling, surface relief gratings in pre-elongated photosensitive colloids of few micrometers length are inscribed using different IPs such as SS, PP, +/- 45, SP, RL, and LR. The deformation of colloidal particles is studied in situ, whereby the local variation of polymer topography is assigned to the local distribution of the electrical field vector for all IPs. Experimentally observed shapes are reproduced exactly with modeling azopolymer samples as visco-plastic bodies in the finite element software ANSYS. Orientation approach correctly predicts local variations of the main axis of light-induced stress in each interference pattern for both initially isotropic and highly oriented materials. With this work, it is suggested that the orientation approach implements a self-sufficient and convincing mechanism to describe photoinduced deformation in azopolymer films that in principle does not require auxiliary assumptions.}, language = {en} } @article{LoebnerLomadzeKopyshevetal.2018, author = {Loebner, Sarah and Lomadze, Nino and Kopyshev, Alexey and Koch, Markus and Guskova, Olga and Saphiannikova, Marina and Santer, Svetlana}, title = {Light-Induced Deformation of Azobenzene-Containing Colloidal Spheres}, series = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, volume = {122}, journal = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, number = {6}, publisher = {American Chemical Society}, address = {Washington}, issn = {1520-6106}, doi = {10.1021/acs.jpcb.7b11644}, pages = {2001 -- 2009}, year = {2018}, abstract = {We report on light-induced deformation of colloidal spheres consisting of azobenzene-containing polymers. The colloids of the size between 60 nm and 2 mu m in diameter were drop casted on a glass surface and irradiated with linearly polarized light. It was found that colloidal particles can be deformed up to ca. 6 times of their initial diameter. The maximum degree of deformation depends on the irradiation wavelength and intensity, as well as on colloidal particles size. On the basis of recently proposed theory by Toshchevikov et al. [J. Phys. Chem. Lett. 2017, 8, 1094], we calculated the optomechanical stresses (ca. 100 MPa) needed for such giant deformations and compared them with the experimental results.}, language = {en} } @article{KochSaphiannikovaSanteretal.2017, author = {Koch, Markus and Saphiannikova, Marina and Santer, Svetlana and Guskova, Olga}, title = {Photoisomers of Azobenzene Star with a Flat Core: Theoretical Insights into Multiple States from DFT and MD Perspective}, series = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, volume = {121}, journal = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, publisher = {American Chemical Society}, address = {Washington}, issn = {1520-6106}, doi = {10.1021/acs.jpcb.7b07350}, pages = {8854 -- 8867}, year = {2017}, abstract = {This study focuses on comparing physical properties of photoisomers of an azobenzene star with benzene-1,3,5-tricarboxamide core. Three azobenzene arms of the molecule undergo a reversible trans-cis isomerization upon UV-vis light illumination giving rise to multiple states from the planar all-trans one, via two mixed states to the kinked all-cis isomer. Employing density functional theory, we characterize the structural and photophysical properties of each state indicating a role the planar core plays in the coupling between azobenzene chromophores. To characterize the light-triggered switching of solvophilicity/solvophobicity of the star, the difference in solvation free energy is calculated for the transfer of an azobenzene star from its gas phase to implicit or explicit solvents. For the latter case, classical all-atom molecular dynamics simulations of aqueous solutions of azobenzene star are performed employing the polymer consistent force field to shed light on the thermodynamics of explicit hydration as a function of the isomerization state and on the structuring of water around the star. From the analysis of two contributions to the free energy of hydration, the nonpolar van der Waals and the electrostatic terms, it is concluded that isomerization specificity largely determines the polarity of the molecule and the solute-solvent electrostatic interactions. This convertible hydrophilicity/hydrophobicity together with readjustable occupied volume and the surface area accessible to water, affects the self-assembly/disassembly of the azobenzene star with a flat core triggered by light.}, language = {en} } @article{IlnytskyiSaphiannikovaNeher2006, author = {Ilnytskyi, Jaroslav and Saphiannikova, Marina and Neher, Dieter}, title = {Photo-induced deformations in azobenzene-containing side-chain polymers : molecular dynamics study}, issn = {1607-324X}, year = {2006}, abstract = {We perform molecular dynamics simulations of azobenzene containing side-chain liquid crystalline polymer subject to an external model field that mimicks the reorientations of the azobenzenes upon irradiation with polarized light. The smectic phase of the polymer is studied with the field applied parallel to the nematic director, forcing the trans isomers to reorient perpendicularly to the field (the direction of which can be assosiated with the light polarization). The coupling between the reorientation of azobenzenes and mechanical deformation of the sample is found to depend on the field strength. In a weak field the original smectic order is melted gradually with no apparent change in the simulation box shape, whereas in a strong field two regimes are observed. During the first one a rapid melting of the liquid crystalline order is accompanied by the contraction of the polymer along the field direction (the effect similar to the one observed experimentally in azopenzene containing elastomers). During the slower second regime, the smectic layers are rebuilt to accomodate the preferential direction of chromophores perperdicular to the field.}, language = {en} } @article{IlnytskyiSaphiannikovaNeheretal.2012, author = {Ilnytskyi, Jaroslav M. and Saphiannikova, Marina and Neher, Dieter and Allen, Michael P.}, title = {Modelling elasticity and memory effects in liquid crystalline elastomers by molecular dynamics simulations}, series = {Soft matter}, volume = {8}, journal = {Soft matter}, number = {43}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, issn = {1744-683X}, doi = {10.1039/c2sm26499d}, pages = {11123 -- 11134}, year = {2012}, abstract = {We performed molecular dynamics simulations of a liquid crystal elastomer of side-chain architecture. The network is formed from a melt of 28 molecules each having a backbone of 100 hydrocarbon monomers, to which 50 side chains are attached in a syndiotactic way. Crosslinking is performed in the smectic A phase. We observe an increase of the smectic-isotropic phase transition temperature of about 5 degrees as compared to the uncrosslinked melt. Memory effects in liquid crystalline order and in sample shape are well reproduced when the elastomer is driven through the smectic-isotropic transition. Above this transition, in the isotropic phase, the polydomain smectic phase is induced by a uniaxial load. Below the transition, in a monodomain smectic A phase, both experimentally observed effects of homogeneous director reorientation and stripe formation are reproduced when the sample is stretched along the director. When the load is applied perpendicularly to the director, the sample demonstrates reversible deformation with no change of liquid crystalline order, indicating elasticity of the two-dimensional network of polymer layers.}, language = {en} } @article{IlnytskyiNeherSaphiannikova2011, author = {Ilnytskyi, Jaroslav M. and Neher, Dieter and Saphiannikova, Marina}, title = {Opposite photo-induced deformations in azobenzene-containing polymers with different molecular architecture molecular dynamics study}, series = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, volume = {135}, journal = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, number = {4}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-9606}, doi = {10.1063/1.3614499}, pages = {12}, year = {2011}, abstract = {Photo-induced deformations in azobenzene-containing polymers (azo-polymers) are central to a number of applications, such as optical storage and fabrication of diffractive elements. The microscopic nature of the underlying opto-mechanical coupling is yet not clear. In this study, we address the experimental finding that the scenario of the effects depends on molecular architecture of the used azo-polymer. Typically, opposite deformations in respect to the direction of light polarization are observed for liquid crystalline and amorphous azo-polymers. In this study, we undertake molecular dynamics simulations of two different models that mimic these two types of azo-polymers. We employ hybrid force field modeling and consider only trans-isomers of azobenzene, represented as Gay-Berne sites. The effect of illumination on the orientation of the chromophores is considered on the level of orientational hole burning and emphasis is given to the resulting deformation of the polymer matrix. We reproduce deformations of opposite sign for the two models being considered here and discuss the relevant microscopic mechanisms in both cases.}, language = {en} } @article{HennebergRochonPanzneretal.2004, author = {Henneberg, Oliver and Rochon, Paul and Panzner, Tobias and Finkelstein, Kenneth D. and Geue, Thomas and Saphiannikova, Marina and Pietsch, Ullrich}, title = {In-situ Investigation of Surface Relief Grating Formation in Photosensitive Polymers}, year = {2004}, language = {en} } @article{HennebergPanznerPietschetal.2004, author = {Henneberg, Oliver and Panzner, Tobias and Pietsch, Ullrich and Geue, Thomas and Saphiannikova, Marina and Rochon, Paul and Finkelstein, Kenneth D.}, title = {X-ray and VIS light scattering from light-induced polymer gratings}, issn = {0044-2968}, year = {2004}, abstract = {Sinusoidally shaped surface relief gratings made of polymer films containing, azobenzene moieties can be created by holographic illumination with laser light of about lambda approximate to 500 nm. The remarkable material transport takes place at temperatures far (100 K) below the glass transition temperature of the material. As probed by visible light scattering the efficiency of grating formation crucially depends on the polarization state of the laser light and is maximal when circular polarization is used. In contrast to VIS light scattering X-ray diffraction is most sensitive for periodic surface undulations with amplitudes below 10 nm. Thus, combined in-situ X-ray and visible light scattering at CHESS were used to investigate the dynamics of surface relief grating formations upon laser illumination. The time development of grating peaks up to 9th order at laser power of P = 20 mW/cm(2) could be investigated, even the onset of grating formation as a function of light polarization. A linear growth of grating amplitude was observed for all polarizations. The growth velocity is maximal using circularly polarized light but very small for s-polarized light}, language = {en} } @article{HennebergGeueSaphiannikovaetal.2001, author = {Henneberg, Oliver and Geue, Thomas and Saphiannikova, Marina and Pietsch, Ullrich and Rochon, Paul and Natansohn, Almeria}, title = {Formation and dynamics of polymer surface relief gratings}, issn = {0378-5963}, year = {2001}, language = {en} } @article{HennebergGeueSaphiannikovaetal.2003, author = {Henneberg, Oliver and Geue, Thomas and Saphiannikova, Marina and Pietsch, Ullrich and Rochon, Paul}, title = {X-ray and VIS light scattering from light-induced polymer gratings}, doi = {10.1088/0022-3727/36/10A/350}, year = {2003}, language = {en} } @article{HennebergGeueSaphiannikovaetal.2002, author = {Henneberg, Oliver and Geue, Thomas and Saphiannikova, Marina and Natansohn, Almeria and Rochon, Paul and Finkelstein, Kenneth D.}, title = {Investigation of material flow on inscribing a polymer surface grating probing X-ray and VIS light scattering}, issn = {0927-7757}, year = {2002}, language = {en} } @article{HennebergChiGeueetal.2001, author = {Henneberg, Oliver and Chi, Li Feng and Geue, Thomas and Saphiannikova, Marina and Pietsch, Ullrich and Rochon, Paul and Natansohn, Almeria}, title = {Atomic force microscopy inspection of the early state of formation of polymer surface relief grating}, year = {2001}, language = {en} } @article{GeueSaphiannikovaHennebergetal.2002, author = {Geue, Thomas and Saphiannikova, Marina and Henneberg, Oliver and Pietsch, Ullrich and Rochon, Paul and Natansohn, Almeria}, title = {Formation mechanism and dynamics in polymer surface gratings}, year = {2002}, language = {en} }