@article{LuetzowWeigelLendlein2020,
  author    = {L{\"u}tzow, Karola and Weigel, Thomas and Lendlein, Andreas},
  title     = {Solvent-based fabrication method for magnetic, shape-memory nanocomposite foams},
  series = {MRS advances},
  volume    = {5},
  journal   = {MRS advances},
  number    = {14-15},
  publisher = {Cambridge Univ. Press},
  address   = {Cambridge},
  issn      = {2059-8521},
  doi       = {10.1557/adv.2019.422},
  pages     = {785 -- 795},
  year      = {2020},
  abstract  = {This paper presents shape-memory foams that can be temporarily fixed in their compressed state and be expanded on demand. Highly porous, nanocomposite foams were prepared from a solution of polyetherurethane with suspended nanoparticles (mean aggregate size 90 nm) which have an iron(III) oxide core with a silica shell. The polymer solution with suspended nanoparticles was cooled down to -20 degrees C in a two-stage process, which was followed by freeze-drying. The average pore size increases with decreasing concentration of nanoparticles from 158 mu m to 230 mu m while the foam porosity remained constant. After fixation of a temporary form of the nanocomposite foams, shape recovery can be triggered either by heat or by exposure to an alternating magnetic field. Compressed foams showed a recovery rate of up to 76 +/- 4\% in a thermochamber at 80 degrees C, and a slightly lower recovery rate of up to 65 +/- 4\% in a magnetic field.},
  language  = {en}
}
@article{IzraylitGouldKratzetal.2020,
  author    = {Izraylit, Victor and Gould, Oliver E. C. and Kratz, Karl and Lendlein, Andreas},
  title     = {Investigating the phase-morphology of PLLA-PCL multiblock copolymer/PDLA blends cross-linked using stereocomplexation},
  series = {MRS advances},
  volume    = {5},
  journal   = {MRS advances},
  number    = {14-15},
  publisher = {Cambridge Univ. Press},
  address   = {New York},
  issn      = {2059-8521},
  doi       = {10.1557/adv.2019.465},
  pages     = {699 -- 707},
  year      = {2020},
  abstract  = {The macroscale function of multicomponent polymeric materials is dependent on their phase-morphology. Here, we investigate the morphological structure of a multiblock copolymer consisting of poly(L-lactide) and poly(epsilon-caprolactone) segments (PLLA-PCL), physically cross-linked by stereocomplexation with a low molecular weight poly(D-lactide) oligomer (PDLA). The effects of blend composition and PLLA-PCL molecular structure on the morphology are elucidated by AFM, TEM and SAXS. We identify the formation of a lattice pattern, composed of PLA domains within a PCL matrix, with an average domain spacing d0 = 12 - 19 nm. The size of the PLA domains were found to be proportional to the block length of the PCL segment of the copolymer and inversely proportional to the PDLA content of the blend. Changing the PLLA-PCL / PDLA ratio caused a shift in the melt transition Tm attributed to the PLA stereocomplex crystallites, indicating partial amorphous phase dilution of the PLA and PCL components within the semicrystalline material. By elucidating the phase structure and thermal character of multifunctional PLLA-PCL / PDLA blends, we illustrate how composition affects the internal structure and thermal properties of multicomponent polymeric materials. This study should facilitate the more effective incorporation of a variety of polymeric structural units capable of stimuli responsive phase transitions, where an understanding the phase-morphology of each component will enable the production of multifunctional soft-actuators with enhanced performance.},
  language  = {en}
}
@article{BehlZhaoLendlein2020,
  author    = {Behl, Marc and Zhao, Qian and Lendlein, Andreas},
  title     = {Glucose-responsive shape-memory cryogels},
  series = {Journal of materials research : JMR},
  volume    = {35},
  journal   = {Journal of materials research : JMR},
  number    = {18},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0884-2914},
  doi       = {10.1557/jmr.2020.204},
  pages     = {2396 -- 2404},
  year      = {2020},
  abstract  = {Boronic ester bonds can be reversibly formed between phenylboronic acid (PBA) and triol moieties. Here, we aim at a glucose-induced shape-memory effect by implementing such bonds as temporary netpoints, which are cleavable by glucose and by minimizing the volume change upon stimulation by a porous cryogel structure. The polymer system consisted of a semi-interpenetrating network (semi-IPN) architecture, in which the triol moieties were part of the permanent network and the PBA moieties were located in the linear polymer diffused into the semi-IPN. In an alkaline medium (pH = 10), the swelling ratio was approximately 35, independent of C-glu varied between 0 and 300 mg/dL. In bending experiments, shape fixity R-f approximate to 80\% and shape recovery R-r approximate to 100\% from five programming/recovery cycles could be determined. R-r was a function of C-glu in the range from 0 to 300 mg/dL, which accords with the fluctuation range of C-glu in human blood. In this way, the shape-memory hydrogels could play a role in future diabetes treatment options.},
  language  = {en}
}
@article{BalkBehlLendlein2020,
  author    = {Balk, Maria and Behl, Marc and Lendlein, Andreas},
  title     = {Actuators based on oligo[(epsilon-caprolactone)-co-glycolide] with accelerated hydrolytic degradation},
  series = {MRS advances : a journal of the Materials Research Society (MRS)},
  volume    = {5},
  journal   = {MRS advances : a journal of the Materials Research Society (MRS)},
  number    = {12-13},
  publisher = {Cambridge University Press},
  address   = {New York, NY},
  issn      = {2059-8521},
  doi       = {10.1557/adv.2019.447},
  pages     = {655 -- 666},
  year      = {2020},
  abstract  = {Polyester-based shape-memory polymer actuators are multifunctional materials providing reversible macroscopic shape shifts as well as hydrolytic degradability. Here, the function-function interdependencies (between shape shifts and degradation behaviour) will determine actuation performance and its life time. In this work, glycolide units were incorporated in poly(epsilon-caprolactone) based actuator materials in order to achieve an accelerated hydrolytic degradation and to explore the function-function relationship. Three different oligo[(epsilon-caprolactone)-co-glycolide] copolymers (OCGs) with similar molecular weights (10.5 +/- 0.5 kg center dot mol(-1)) including a glycolide content of 8, 16, and 26 mol\% (ratio 1:1:1 wt\%) terminated with methacrylated moieties were crosslinked. The obtained actuators provided a broad melting transition in the range from 27 to 44 degrees C. The hydrolytic degradation of programmed OCG actuators (200\% of elongation) resulted in a reduction of sample mass to 51 wt\% within 21 days at pH = 7.4 and 40 degrees C. Degradation results in a decrease of T-m associated to the actuating units and increasing T-m associated to the skeleton forming units. The actuation capability decreased almost linear as function of time. After 11 days of hydrolytic degradation the shape-memory functionality was lost. Accordingly, a fast degradation behaviour as required, e.g., for actuator materials intended as implant material can be realized.},
  language  = {en}
}